ISM-WF200 英文.cdr

MN - ISM-WF200 -E
www.insize.com
ISM-WF200
WIFI DIGITAL MEASURING MICROSCOPE
OPERATION MANUAL
V0
Description
Attention
Thank you for choosing ISM-WF200 microscope!
The ISM-WF200 microscope is an exciting and dual-usage digital
microscope; it can be used either with a WiFi connection or
with a USB wired connection. The dual-usage microscope enables
you to clearly study micro-objects, the WiFi connect not
only gives you freedom to move away from a laptop/PC, it also
enables you to share your study with others connected to the
WiFi. The ISM-WF200 has a wide scope of applications, such as,
 Industrial Inspection
 Computer Parts inspection
 Telecom module inspection
 Scientific teaching tool
 Medical analysis
 School Research tool
 Insect dissection / examination
 Plant dissection / examination
 Skin examination
 Textile Inspection
 Collections / Coin/ Jewelry Inspection
 Printing Inspection
 And more…………..
Please read this manual carefully before using ISM-WF200
microscope!!!
1. Avoid touching the lens.
2. Protect the product from electrostatic damage.
3. Do not attempt to disassembly any part of this product.
4. Do not attempt to service this product yourself. Opening the
covers may expose you to dangerous
voltage points or other risks.
5. Store and operate ISM-WF200 microscope at Temp: -20 ~ 45°C,
Humidity: 45% ~ 85%, storing
and operating outside these limits may reduce the life of the product.
6. Do not expose this product to water or other liquids. If water or
other liquids enter the product,
immediately power off the product. Continued use of the product may
result in fire or an electrical
shock.
7. Do not use any detergent or volatile solution, as this will damage
the camera case, painted surfaces
and lens. To clean the product uses only a soft cleaning cloth.
8. Do not place this product near a heat source or expose direct
flame, avoid the lens damaged by
high temperature or humidity
9. If the lens is dirty, please use a kens brush on soft cloth to wipe
clean. Avoid touching it with your
fingers. Exercise care to avoid scratching the lens.
10. Need to read ISM-WF200 microscope User’s Manual before
using and storing it.
11. To avoid electric shock, remove all electricity source before
removing PC.
1
2
Using with iPad
Structure
The Power “OFF/USB—WiFi” Switch:
WiFi: ISM-WF200 Microscope works in WiFi mode when switch is
moved to “WiFi” side.
OFF/USB: Power-off WiFi Microscope when switch is moved to
“OFF/USB” side; also, USB microscope works if connected to PC’s
USB port via MiniUSB cable.
WiFi Indicator (Blue LED):
Flashing light indicates data transmission; Constant light indicates
no data transmission.
Power Indicator (Blue LED):
Lights when power on WiFi or connected to PC or AC adaptor via
MiniUSB cable.
Battery Indicator (Blue LED or Red LED):
Red LED lights when battery level low; Blue LED lights when battery
charging full.
Charge Indicator (Red LED):
Lights when the battery is being charged; turn off when the
battery is fully charged.
Charging Instructions:
Connect the DC Adapter (plug the AC adapter into an AC outlet) or
PC’s USB cable, it charges whether the power switch is on WiFi or
OFF/USB. (We DO NOT recommend charging WiFi Microscope while
using)
3
1. Download and install the “ISM-PAD” app from “App Store”
or the Disc enclosed for your Windows or IOS device.
Note 1: Search “ISM-PAD” in App Store.
2. Slide the Power switch to the “WiFi”, and the power LED
indicator will light, wait for ~20 seconds until the WiFi indicator
and the illumination LEDs light, then the WiFi signal will be
transmitting correctly.
3. Check the wireless connection on your Phone/Tablet or PC
and a list of available networks will appear. Select the SSID
“ WiFi2SCOPE_xxxxxx” network from the list to connect; the
network “WiFi2SCOPE_xxxxxx” requires a password: enter the
password “12345678” and click Ok.
4. Once connected, open the “ ISM-PAD” application to see
your images. The WiFi indicator LED flashes and video stream
signal should be displayed in the app. Video streaming can be
broadcasted to many devices, but the frame rate of live video
will decrease as the number of receiving devices increase.
Capture photo or record video (You must set the pixel resolution
to 640x480 when recording video).
4
Photos folder or videos folder.
Input the actual length of the line; click “ ok” and on the live
video to pop-up this below screen:
Navigation icon—moving a dot left/up/down/right for
calibration or measurement operation.
Calibration and measurement icon.
Switch between photo taking and video.
Resolution Setting . ( When changing the resolution, you must
wait until the illumination LED is off and lights up again
before clicking live video ‐ it takes about 5 seconds).
Calibration and Measurement’s Guide:
To obtain the accurate measurement data, please calibrate before
any measurement function at each magnification. Use the enclosed
calibration ruler as the to-be-observed object. Bring photo into focus
by turning the “Focus & Magnification adjustment wheel”; Click
to
pop‐up this below screen:
Now the calibration is completed, you can make measurement
features accurately on the live video at this same focus. (Don’t
subsequently adjust the “Focus & Magnification adjustment wheel”)
If the new photo object is not in focus, please only adjust the distance
between the microscope and the object till the photo is clear. This
measurement data can be saved inside the taken photo.
Using with Windows in WiFi mode
Double‐click ISM‐WF Partner icon after completing installation
to pop‐up the below screen:
Click “ Calibration” to back the live video, click two dots ( moving
the dot by clicking navigation icons,which draw a your desired line,
then click on the live video to pop-up this screen:
5
6
Click “ Preview
” icon and the ISM‐ WF200 main screen will
display video as below: (it waits about 5 seconds to display video; if
the frame rate of live video is slow, please click “Preview” icon once
again to try.)
When you change the resolution, you must wait until the
illumination LED is off and lights up again before clicking OK-it
takes about 5 seconds.
Setting: click to pop‐up the pen setting: (If the " Line width" is
2 or 3 Pixel, the " Pen Type" must be Solid-Line)
Menu:
File
Select a photo or video, click “File”on menu bar or right‐key
to pop‐up the drop‐down menu for operation.
Open: Open the selected photo or video to be viewed.
Save As: Save the selected photo or video file as the desired
folder and file format.
Delete: Delete the selected photo or video.
Delete All: Delete the all photos or videos in the photo or video
folder.
E‐ Mail: Email the selected photos through your default email
account.
Favorites: Open the folder which contains the captured photos
and recorded videos.
Setting
Device Setting: Select “ Video setting” to pop‐ up the window
below for video parameter setting:
7
8
Language: The language selection allows you to select the
ISM‐WF200 interface language.
Capture
Take Picture: You can capture a photo by clicking the snapshot
Button .
Take/ Stop Video: In the active live video window, click on
to
record a video.
Video Processing
Please click “Preview” to resume the live video after finished
operation of video processing below.
Horizontal Mirror
Vertical Mirror
Negative
Binary Segmentation
Monochrome display (Red)
Monochrome display (Green)
Monochrome display (Blue)
Calibration on Video:
1. Frame rate: is the number of frames or photos that are
projected or displayed per second. The number range is 1~30.
2. Timer limit: is the time of video recording to avoid video file
size exceeding the disk space. The number range is 1~99999.
Take time‐lapsed pictures: Press the time‐lapsed button
on
the active preview window
It is strongly suggestion: To obtain the accurate measurement
data, please calibrate before any measurement function at each
magnification.
Select a known measurement standard as the to-be-observed
object, such as a ruler, to be used for calibration. Bring photo
of the selected ruler into focus by turning the “ Focus &
Magnification adjustment wheel” , determine the magnification
by taking a reading from the scale on the focus dial as below:
Enter the scale value in the “ Scale” box in the right‐ hand
scale box of the screen as below:
9
10
In the live video window click on the calibration button
, and then
click and drag to 2mm length, a small window pop up, enter the actual
length(The example is 2mm) to click “OK” Button.
Now the calibration is completed, you can make measurement
features accurately on taken photos or real‐ time video at this
focus point (Don’t subsequently adjust the “Focus & Magnification
adjustment wheel”).If the new photo object is not in focus, please
only adjust the distance between the microscope and the object till
the photo is clear, and then capture the photo to measure it.
Line measurement:
This allows you to measure the linear distance between two
points. Simply click and drag to the desired length, and click
again to finish.
Point to Line Measurement
This allows measurement of a line 90 degree from a certain line.
Simply create a line to represent the base by clicking once to
start, drag, and then click again to set the endpoint. Branch off
from the base line to start measuring the line that is 90 degree
from the base line and a final click to finish the measurement.
The software will automatically calibrate the scale of
magnification and will show the calibrated scale of magnification
at the right‐hand box of calibration button as below:
Continuous Line Measurement
This allows measurement of the distance between multiple
connecting lines. Simply click and drag to form one section
of distance, click again to start another section. Continue
until the total desired distance is measured. Double‐click to
finish.
Polygon Measurement
This allows measurement of a polygon. Simply click and drag
to form the desired length, and click again to start the next
section, double‐click to finish the polygon measurement.
Radius of Circle Measurement
This allows you to measure the circumference, area, and radius
of a circle. Simply click and extend out to the desired radius.
Diameter of Circle Measurement
This allows you to measure the circumference, area, and radius
of a circle. Simply click and extend out to the desired diameter.
Three Point Circle Measurement
This allows the measurement of the circumference, area, and
radius of a circle. Simply click on any three points on the circle
you wish to measure.
11
12
Three Point Arc Measurement
This allows a measurement of an arc. Click on three consecutive
points on an arc to measure.
Three Point Angle Measurement
This allows the measurement of an angle. Start at the pivot point
and extend out to start measuring an angle.
Four Points Angle Measurement
This allows the measurement of an angle by selecting four points.
Simply select two points from one line segment and another two
points from another line segment to complete the angle
measurement.
Photo Viewing, Measure and Calibration
You can double‐click the selected Photo to measure and view it
as below shown:
:Open a photo for measure from a folder.
: Save as
: Print this photo.
: Select one target.
: Measure function items.
: Pen setting.
: Add text into photo.
: Delete the selected target.
: Move the selected target.
: Calibration.
For measure, please enter the magnification if there is not
number. The number is the scale value of roller at the baseline
of the captured photo.
Photo file name: yyyymmddhhmmss_ nnnx_Nxxxx is combined by
date, time, magnification and serial number. For example,
Still_ 2009‐ 03‐ 06_ 102949_ 060X_ N0002 figures: Number is
0002, magnification is 60, date is Mar‐ 06‐ 2009, time is
AM10: 29: 49.
The program will auto load the magnification when you measured
it if you put the scale before you capture the photo.
13
14