User Guide Summit Edge 700 Quick Reference Guide

User Guide Summit Edge 700 Quick Reference Guide
Important Safety Information
To prevent the unexpected danger or damage please read this information before installing and
repairing the phone. There are “Warning”, it means as follows;
Warning: To reduce the possibility of electric shock, do not expose your phone to high humidity areas,
such as a bathroom, swimming area, etc.
Warning
1.
Only trained and qualified service personnel shall install, replace or service the phone.
2.
Do not spill liquid like water on the phone. If so, call for the service center as this may result in
a fire or an electric shock.
3.
If you see smoke or smell something during, unplug the phone line. Call for service centre
immediately.
4.
Do not tug the power cord or the phone line. This may result in a fire, an electric shock or
equipment damage.
5.
Do not use the phone during a thunderstorm. Lightning strike may result in a fire, severe electrical or
acoustic shock.
6.
Ensure that children do not pull on phone cords. This may injure children or result in equipment
damage.
7.
The ear-piece houses a magnetic device which may attract pins or small metal objects. Keep handset
clear of such objects and check before use.
8.
Avoid placing the phone in an area that is dusty, damp or subject to vibration.
9.
Choose a site that is dry and well ventilated.
10.
Do not put the heavy things on the phone.
11.
Do not drop or throw the phone.
12.
Static electricity discharge will damage electronic components.
13.
Keep out of direct sunlight and away from heat.
14.
No user serviceable parts inside. No not insert a screw driver or any metal objects into the phone.
This may cause electric shock or damage the equipment and will render the warranty void.
15.
Clean the phone with a soft, dry cloth only. Do not use volatile liquids such as petrol, alcohol or
acetone as this may cause a fire or result in discoloration or damage to plastics. Do not clean with
wax or silicon products as these may enter the equipment and cause operation to become unreliable.
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol is attached to a product it means the product
is covered by the European Directive 2012/19/EC.
2.
All electrical and electronic products should be disposed of separately from the municipal
waste stream via designated collection facilities appointed by the government or the local
authorities.
3.
The correct disposal of your old appliance will help prevent potential negative
consequences for the environment and human health.
4.
For more detailed information about disposal of your old appliance, please contact your
city office, waste disposal service or the shop where you purchased the product.
EDGE 700 24-Button Digital Telephone Description
Button
4
LCD Display
5
3 Soft
Quick Guide
Description
Displays information about telephone status, dialing directories, and test
message information
Used in conjunction with fixed and flexible features, and the function changes in
relation to call progress, as indicated on the LCD display.
6
Visual LED
Illuminates when the phone is ringing.
7
Flexible
Buttons
Some flexible buttons are pre-programmed in the system for line appearances,
loop functions etc. The remaining flexible buttons can be user-programmed.
8
Hands-free
Microphone
Microphone is used for hands-free speakerphone function
9
Trans/PGM
This button is used to initiate a call transfer (TRS) or to enter programming
mode (PGM).
Speed
Used to access speed dialing, speed programming, save number redial, and
last number redial.
DND
The DND (Do Not Disturb) feature blocks all incoming calls. When DND is
active, the red LED in this button is illuminated.
Call Back
A station can initiate a call back request to a busy station. Once that station
becomes idle, the initiating station is signaled.
10
Nav Button
Navigate through (and make selections on) the display/menus
11
Volume
The volume button adjusts the audio levels for ringing, handset and
speakerphone functions.
12
Hold/Save
This button is used to put a call on hold or save information when programming.
14
Speaker
Speaker toggles the speakerphone state, and the red LED is illuminated when
the speakerphone is active.
LDP Keyset User Operation
Receiving calls _ Answering a Call While Idle :
1. Lift the handset and press the flashing Flex button (as
needed), the call will be connected.
Responding to a Call While Busy
1. Press [Hold/Save] and/or
2. Press the flashing CO line button.
Answering Calls to Other Stations
To answer a call ringing at another station:
1. Lift the handset,
2. Dial 7 (Directed Call Pick-Up code),
3. Dial the Intercom Number of the ringing station; the
call will be connected.
To answer a call ringing at a station in your
group:
1. Lift the handset,
2. Dial * * (Group Call Pick-Up code), the call is
connected.
Using Do-Not-Disturb (DND) to Block Incoming
Calls
To toggle DND ON and OFF:
1. Press the [DND] button.
Forwarding calls to another Station or Voice
Mail
To activate Call Forward from your phone to
another phone or internal system resource:
1.
2.
3.
4.
Lift the handset,
Press the [Fwd] Soft button,
Dial the type of forward code 1-4
Dial the destination number.
Placing Intercom calls
To place an Intercom call:
1. Lift the handset,
To enter a Station Speed Dial number with CO
Line and Name:
1.
2.
3.
4.
5.
6.
7.
Press [Trans/PGM],
Press [Speed],
Dial the desired Station Speed Dial bin number,
Select/dial the CO line/group,
Dial the desired number to be stored,
Press [Hold/Save],
Enter the associated name if desired, using the
alpha-numeric entry chart,
8. Press [Hold/Save].
To assign a Station Speed Dial number directly
to a Flex button:
1. Press [Trans/PGM],
2. Press the desired [Flexible] button,
3. Dial the desired number including CO Line/Group
access code
4. Press [Hold/Save],
5. Enter the associated name if desired, using the
Character Entry chart,
6. Press [Hold/Save].
ACNR: To retry a busy external number until
answered
To set up an ACNR, while on an outgoing call:
1. Use the Navigation button to display the next menu
and select the [ACNR] Soft button,
2. Hang-up handset.
To cancel the ACNR request:
1. Press the [ACNR] Soft button.
Call Transfer: Sending a call to a different
destination
To Transfer an active call:
2. Dial the Intercom number of the desired station,
3. On answer or Splash tone, speak to the called party.
1. Press [Trans/PGM],
2. Call receiving party,
3. Hang-up with or without announcement.
Using Camp-On when calling a busy station
To Camp-On (wait off-hook) for a busy station:
Call Hold: Placing a call in a waiting state
To place a call on Hold:
1. Press [*] and wait an answer.
Using Last Number Redial (LNR)
To dial the Last Number for an external call:
1. Lift the handset,
2. Select the [Redial] Soft button,
3. Press [▼ volume ▲] to select from the last 10
numbers dialed,
4. Press the [Send] Soft button or [Hold/Save].
Using System Speed Dial Numbers
To place a call using System Speed Dial:
1. Lift the handset,
2. Press the [Speed] button,
3. Dial the desired System Speed Dial bin number
Using and Entering Station Speed Dial
Numbers
To place a call using Station Speed Dial:
1. Lift the handset,
2. Press [Speed],
3. Dial the desired Station Speed Dial bin number
1. Press [Hold/Save].
Joining Multiple People in a Conference
To establish a Conference:
1. Establish call with one of the desired conference
parties,
2. Select the [Conf] Soft button,
3. Establish call with the other conference party,
4. Select the [Conf] Soft button,
5. Select the [Conf] Soft button again to establish the
conference.
To place a Conference on Hold:
1. Press the [Hold/Save] button.
To retrieve the Conference:
1. Select the [Conf] Soft button.
To make an External-parties-only Conference:
1. Establish conference with two external parties,
2. Select the [Conf] Soft button to exit.
To enter pre-opened Conference Room:
1. Dial 5 7 X when X is the conference room number.
User Program Codes for SUMMIT
• ▶ Press the [Trans/PGM] button
• ▶ Enter the desired feature code below table
CODE
FUNCTION
CODE
FUNCTION
11
Station Ring Type
51
Set Preselected: Custom Message
12
CO Ring Type
52
PGM Custom Message
13
Answer Mode
53
Active Conference Room
14
Call Coverage Attribute
54
De-active Conference Room
15
Station Ring Download
55
Monitor Conference Group
19
EAR-Mic. Headset
61
Headset or Speaker Mode
21
COS Down
62
Headset Ring Mode
22
COS Restore
71
LCD Display Language
23
Walking COS
72
MPB Version
24
ICR Scenario
73
BGM
25
LIP Keyset Status
74
Register STA Name
26
Call Profile
75
Display Phone IP Address
31
Message Retrieve Method
76
Change Phone IP Address
32
Message Retrieve Example
77
Display MAC Address
33
User Authorization Register
78
Network Configuration
34
DID DISA Call Wait
79
Display Phone Version
35
Choice Executive/Secretary Message
7*
Display Add-On Package
36
Send SMS Message
*0
Hot Desk Login
37
Register Mobile – Extension
*6
Set Forced Forward Destination
38
Active Mobile-Extension
*7
Forced Forward to Destination
39
Register Mobile CLI
*8
Register Bluetooth (N/A)
30
VM Mobile Notify
*9
Bluetooth Usage (N/A)
41
Set Wake Up Time
**
Hot Desk Log Out
42
Wake Up Disable
*#
Enter Admin
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement