Corporation of the Township of Amaranth Tender for 2018 Tandem

Corporation of the Township of Amaranth Tender for 2018 Tandem
Corporation of the Township of Amaranth
Ben Ryzebol – Director of Public Works
Public Works Department – 374028 6th Line, Amaranth ON L9W 0M6
Tel: (519) 941-1065
Fax: (519) 941-1802
Tender for 2018 Tandem Truck Cab & Chassis
Complete with Plow Equipment
Sealed Tender to be delivered to:
Ben Ryzebol
Director of Public Works
Township of Amaranth
Administration Office
374028 6th Line
Amaranth, ON L9W 0M6
May 24, 2017
Courier Address:
374028 6th Line
Amaranth, ON L9W 0M6
1. Tender closes at 4:00 p.m. on Thursday, June 15, 2017. Sealed tender to be clearly marked.
2. This specification covers a 6 ton Diesel Snow Plow Truck.
3. This specification lists only the major details of a unit, therefore it is the supplier’s responsibility to
deliver a fully equipped vehicle with compatible components to provide dependable efficient service.
4. Where minimums are called for, the vehicle must meet or exceed the capacity, size or performance
specified.
5. Vehicles shall meet or surpass the mandatory requirements of the “Canadian Motor Vehicle Safety
Regulation: and must bear the National Safety mark.
6. Signed manufacturer’s factory warranty shall be supplied.
7. Lowest or any tender not necessarily accepted.
8. Tender price to be valid for 120 days.
9. Tender must be sealed and clearly marked “Truck Tender”.
10. Further information may be obtained by contacting the above.
11. Tenders are to be returned in hard copy (paper) format. Electronic formats will not be accepted.
Unit Price for Cab and Chassis,
complete with Plow Equipment
Air Conditioning Tax:
$
Tire Tax:
$
Delivery Charges:
For completed unit to works yard –
393045 County Rd 12, Amaranth, ON
Discount for payment of cab and chassis
within 30 days of delivery to body builder.
H.S.T.
TOTAL TENDER PRICE
$
$
$
$
$
Approx. Delivery Date:
Company:
Address:
Telephone
Email:
Signature:
Print:
Tender: 2018 Tandem Truck Cab & Chassis Complete with Plow Equipment
Closing Date: 4:00 p.m. June 15, 2017
Township of Amaranth
Appendix A
Vehicle Specifications
Vehicles must be supplied with suitable components to comply with the following specifications in all
aspects:
MAKE:
YEAR:
MODEL:
Specify body builder for plow equipment:
AXLES
Yes
No
Yes
No
Front axle shall be a Meritor MFS-20-133A set back front axle of 22,000 lbs
minimum capacity with torque rods.
Front shock absorbers
Front axle bearings to be oil fed.
Rear axle shall be 46,000 lbs. minimum capacity. Lube: Synthetic Oil.
Rear axle shall be tandem, dual drive, lube oil pump with interaxle differential and
driver controlled main locking differential in rear-rear axle and forward rear.
Rear axle ratio shall be 4.88
Rear tandem axles shall have a 56-inch spread between the axles. Must comply and
be labelled with SPIF Regulations.
The rear axle make shall be Meritor (Rockwell) model RT-46-164-P
BRAKES
Service Brakes – Full Air brakes – ABS
“S” Cam Air Brake System with Dust Shields Front and Rear.
Front brakes size 16 ½” x 6” minimum
Rear brakes size 16 ½” x 7” minimum with asphalt spreader clearance mounting.
Air tanks to have manual drains included.
Air compressor – 19.0 cfm capacity minimum with dry type air cleaner on intake
shall be supplied.
Tender: 2018 Tandem Truck Cab & Chassis Complete with Plow Equipment
Closing Date: 4:00 p.m. June 15, 2017
Heated Air dryer shall be supplied. Type: AD-9
Brake chambers must be 24 square inch minimum on front brakes and 30 square
inch minimum on rear brakes.
Automatic slack adjusters, front and rear (HALDEX), safety brake travel indicators
Tractor Package- Lines extended to end of frame, including glad hands & 7-way
trailer cord receptacle. Hand control valve and tractor protection valve.
POWER STEERING
Yes
No
Yes
No
Yes
No
Yes
No
Dual power steering boxes shall be supplied
FRAME
Frame reinforcement must be full length, outer “C” Channel, heat
treated alloy steel (120,000 PSI Yield); 10.813 inch x 3.892 x 0.312
inch x 480 OAL
Frame rails heat treated alloy steel 120,000 PSI yield;
10.125 inch x 3.58 inch x 0.312 X 400 maximum OAL
SPECIFY:
SPECIFY:
Mounting of snow plow cheek plates shall be possible.
Front frame extension shall be 24 inches minimum with 1/4 inch insert
Front bumper shall be supplied, Heavy Duty Painted Steel
SUSPENSION
C.A. shall be 138" approx. to accept the combination plow equipment
NOTE: dealer to check with body builder prior to ordering chassis
Front spring capacity at the ground - 22,000 lbs
Rear suspension Tuftrac Model 46,000 lbs minimum shall be supplied with shock
absorbers, both axles
WHEELS, TIRES AND RIMS
Tire size front:
425-65R-22.5 Michelin XZY3 L20 ply
Tire size back:
11R x 22.5 Michelin XDE M/S
Rim size front:
Disc, 22.5 inch 10-stud (285.75 MM BC) hub piloted, flanged nut, metric mount,
22.5 x 12.25 Steel Disc Wheels
Tender: 2018 Tandem Truck Cab & Chassis Complete with Plow Equipment
Closing Date: 4:00 p.m. June 15, 2017
Rim size back:
22.5 x 8.25, 10 Stud Hub piloted .625 Thick Centres, Steel rims, powder coated.
White
Rims shall have load and pressure ratings equal to or greater than those of the
tires. Spacers shall be supplied & installed between rims & drums
ENGINE
Engine shall be wet sleeve, 12.8 litre minimum, 410 HP with 1550 lb/ft
torque @1000 RPM 2100 RPM governed. Current EPA emissions
Compliant
Yes
No
Yes
No
Yes
No
SPECIFY:
Exhaust system shall be single, vertical, aluminized steel muffler, chrome spout, tail
pipe including stainless steel muffler guard and grab handles, mounted on the right
hand side, cab mounted. To be discussed with body builder.
Front PTO Crankshaft Adapter
Prior to the delivery of truck, engine shall be set up using proper electronic diagnostic
equipment to the specifications of the Township of Amaranth
TRANSMISSION & CLUTCH
Approved transmission:
RTLO(F)-16913A 13 Speed Manual with double overdrive, Air Shift and Internal Lube
Oil Pump. Synthetic transmission oil and transmission oil cooler, air to oil type.
NOTE: Requires transmission lube pump
Approved clutch:
Eaton Fuller MP152-CLS with 2050 lb./ft. torque rating
Cast iron clutch housing
Clutch Extension hose at clutch release bearing
Driveline – 1800 Series with half round yoke
ENGINE EQUIPMENT
Engine shall be supplied with compression brake with dash mount selector and on/off
switches.
Batteries: 3 - 12 volt batteries shall be supplied, 2775 CCA total.
The battery box and lid shall be mounted under passenger seat in cab, vented.
Battery shut off switch inside cab out board of driver’s seat.
Air cleaner - Heavy duty dual stage dry type shall be supplied with cab controlled
inside/outside air induction with dash mounted air restriction gauge.
Tender: 2018 Tandem Truck Cab & Chassis Complete with Plow Equipment
Closing Date: 4:00 p.m. June 15, 2017
Alternator - 160 amp. capacity Model 36SI minimum
A Borg Warner K26 fan drive with automatic on/off shall be supplied.
Fan over ride manual custom switch in cab with above
PTO Effects – engine front adapter plate, mounted.
Block heater 1500 watt mounted left side of cab under driver’s door with flap and
current sensor light.
Spin on Coolant Filter / Premium Radiator hoses
Fuel/Water separator
Starter to be Delco RV 39MT with OCP
CAB
Conventional cab with the following equipment shall be supplied:
Custom interior trim package 2 in-dash cup holders, padded insulated headliner,
insulated firewall and insulated rear cab wall, door panels with map pocket,
overhead console with dual storage pockets and retainer net. Dark grey in colour
Driver seat :
Air suspension, high back cloth with dual arm rests and lumbar supports. Four way
adjustable (national 2000-195)
Passenger Seat: Stationary, midback, cloth, matching colour
5 lb. fire extinguisher mounted on floor beside driver’s seat and accessible when
driver’s door opened.
Steering Column shall be telescoping and tilting with 18” steering wheel.
Air ride conventional cab, rear mounted
Windshield –curved glass, all glass to be O.E.M. tinted. Cowl tray lid at bottom of
windshield stopping snow from packing below wipers.
2 rectangular 16 inch x 7 inch stainless steel west coast mirrors, heated and two
8 inch convex mirrors, heated
Exterior sunshade visor to include flush mounted LED clearance marker lights.
6 additional O.E.M. powered body builder light switches, mounted in- dash,
connected to electrical box.
Complete gauge cluster to include engine oil pressure, water temperature,
voltmeter and air pressure (dual) with alarm or buzzer and light warning system.
Inner skirt under hood sound abatement package to prevent road dirt from
engine.
Factory installed AM/FM Weatherband radio and 29 channel Cobra CB with (2)
antennas shall be supplied with blue tooth and weather band.
Yes
No
Tender: 2018 Tandem Truck Cab & Chassis Complete with Plow Equipment
Closing Date: 4:00 p.m. June 15, 2017
Dual chrome air horns with covers shall be supplied.
Engine hour meter and tachometer shall be supplied.
Chrome Grab Bars on each side to assist easy entry and exit shall be supplied
with single rubber insert.
Factory Air conditioning - integrated heater and defroster shall be supplied
Heater must be high output
Back-up 102 DBA Alarm, to be supplied and installed.
Electric Power Windows and door locks on drivers and passenger side factory
installed
Electric wipers dual two speed, intermittent and electric washer pump
Superior Custom rubber floor mats to be included.
Cab skirts, both sides, to be supplied.
Triangle Roadside stand alone safety markers included in cab
Circuit breakers with manual reset – replaces all fuses except 5 amp.
O.E.M electrical junction box in-cab behind driver’s seat for body builder access
for all body lights. All connections must be in cab, no multiplex wiring.
FUEL TANK
Yes
No
Yes
No
Single non-polished aluminium 80 US gallon with stainless steel straps mounted on
drivers side. Expanded aluminium tread plate cab entry steps both sides.
PAINT
Outside paint shall be solid Dupont N6661-HP Shell Yellow 2MR ON 5000. Must be
base coat/clear coat.
Chassis Gloss Black
HOOD/FENDER/GRILLE
Must be forward tilting with hood service hatch, left side for checking engine fluid
levels with enhanced dip stick location.
Must be provided with fender extensions with extended full width front fender mud
flaps.
Stationary chrome grill with bug screen behind grill.
Yes
No
Tender: 2018 Tandem Truck Cab & Chassis Complete with Plow Equipment
Closing Date: 4:00 p.m. June 15, 2017
WARRANTY
Optional Warranty pricing to be included in unit price:
SPECIFY
Engine: 7 years (84 months) 250,000 miles including turbo and
injectors
SHOP MANUALS
Yes
No
Yes
No
Shop & parts repair manuals for the truck and engine shall be supplied.
NOTE
Truck Dealer to submit complete specification sheets for Cab and Chassis with bid
submission.
Tender: 2018 Tandem Truck Cab & Chassis Complete with Plow Equipment
Closing Date: 4:00 p.m. June 15, 2017
ALL SEASON COMBINATION DUMP BODY/SPREADER and PLOW EQUIPMENT
Ontario O.E.M. Manufacturer to be ISO9001-2008 Registered & Installed in Ontario
1.
GENERAL
These specifications described an All Season Combination Dump Body
and Sand/Salt Spreader. The dump box shall remain stationary on the
chassis frame while spreading. Rear discharge shall be front hoist tilt
action as per conventional dump bodies. The unit will be oval shaped to
permit gravity flow unloading. The main conveyor will be centred and
recessed along the length of the box. The cross conveyor will be chassis
frame mounted and shall be positive belt drive and bi-directional with R.H
poly lined material chute.
YES: ______
NO: ______
SPECIFY:
Viking model Proline 1415 HW-HT Hi-Tensile Hardox 450 steel or
approved equivalent.
MAKE: _______________
MODEL :
_______________
The bidder will arrange a working demonstration of any unit offered as an
approved equivalent at the municipality’s location prior to the tender closing
date.
2.
YES: ______
NO: ______
YES: ______
NO: ______
DIMENSIONS
To provide optimum combination of legal payload and capacity all
dimensions below are maximum/minimum and will be exactly as specified.
Body shall be smooth rolled oval shaped- no breaks or formed bends,
permitting materials to unload by gravity, flow into spreading positions.
Total weight of the complete body assembly in ready to work condition
including hoist, tarp, tailgate, cross conveyor, main conveyor and all other
required components not to exceed 7,595 lbs.
YES: ______ NO: ______
YES: ______
NO: ______
SPECIFY: __________
LBS.
Water level capacity will be 14.0 cu. yd.
YES: ______
NO: ______
10" Hardwood sideboards painted black
YES: ______
NO: ______
Water level capacity with 10" sideboards will be 17.0 cu. yd.
YES: ______
NO: ______
Outside length 15' minimum.
YES: ______
NO: ______
Inside length 14' minimum.
YES: ______
NO: ______
Tender: 2018 Tandem Truck Cab & Chassis Complete with Plow Equipment
Closing Date: 4:00 p.m. June 15, 2017
Overall width 8' maximum
YES: ______
NO: ______
Height of sides 53" from conveyor floor
YES: ______
NO: ______
Height of tailgate 62" from conveyor floor.
YES: ______
NO: ______
Include Shovel holder on front of body, drivers side.
YES: ______
NO: ______
Height of front panel approx. 60".
YES: ______
NO: ______
Top rail of body will be 6" x 4" x 3/8" square tubing
YES: ______
NO: ______
All body welds will be 100% continuous inside and outside
YES: ______
NO: ______
Specify _______________
Smooth rolled body sides to be fabricated from:
3/16" Hardox 450 steel 180,000 > 203,000 P.S.I
_____________________
Body front panel will be 3/16" Hardox 450 steel 180,000 > 203,000 P.S.I
YES: ______
NO: ______
Dump box access aluminum ladder shall be 15" wide located on drivers
side at front of box and be M.T.O. fold-up.
YES: ______
NO: ______
3.
HOIST
Hoist shall be a front mounted top lift nitrated three (3) stage telescopic
with 5 ½” bore.
YES: ______
NO: ______
Hoist class shall be 80/30 ton.
YES: ______
NO: ______
Cylinder stroke shall be 330 cm (130") minimum
YES: ______
NO: ______
Dump box tipping angle shall be 50 degrees.
YES: ______
NO: ______
The front head of the body will be completely clean and clear of any type
of recesses or protrusions into the body including hoist dog house,
bulkhead, etc.
YES: ______
NO: ______
Hinge Dia. shall be 2.5" with grease fittings and integral body prop.
YES: ______
NO: ______
Hoist control valve shall be air operated.
YES: ______
NO: ______
Tailgate height shall be double acting.
YES: ______
NO: ______
Tailgate height shall be 55" from conveyor floors.
YES: ______
NO: ______
Tailgate shall be U shaped.
YES: ______
NO: ______
Construction shall be of 3/16" Hardox 450 steel with 3/16" formed cross
bracing
Specify:
4.
TAILGATE
Tender: 2018 Tandem Truck Cab & Chassis Complete with Plow Equipment
Closing Date: 4:00 p.m. June 15, 2017
Latch mechanism for the tailgate shall be air trip and latch using two air
pot boosters, complete with bolt on brake pot chamber covers with in cab
control.
YES: ______
NO: ______
Spreader chains and brackets shall be supplied on tailgate and rear post.
Chains shall be grade 70 coil proof 3/8" minimum.
YES: ______
NO: ______
Tailgate will include asphalt door with adjustable cantilever handle to
outer curbside of body.
YES: ______
NO: ______
The main conveyor shall be recessed along the length of dump box floor,
rear conveyor or cover screen to be pinned on - not bolted.
YES: ______
NO: ______
The conveyor chain shall be a minimum of 30,000 lbs. tensile strength
self cleaning pintle chain.
YES: ______
NO: ______
½" x 1 ½" cross flights welded to every 2nd. link (approx.4 ½”)
YES: ______
NO: ______
The main conveyor shall be a single 25:1 high efficiency planetary drive
with high torque low speed motor.
YES: ______
NO: ______
This drive shall deliver 50000 IN/LB torque intermittent with 34000 IN/LB
constant.
YES: ______
NO: ______
Planetary drive close coupled to main conveyor shaft.
YES: ______
NO: ______
5.
MAIN CONVEYOR
MAKE: _______________
Specify make and model of planetary.
MODEL:______________
The flow control gate between main and cross shall be screw adjustable
by hand crank from drivers side of dump body and have a gate height
calibration sticker.
YES: ______
NO: ______
The cross conveyor shall be a positive rubber belt drive, bi-directional
cross conveyor with right hand poly lined material chute.
YES: ______
NO: ______
The cross conveyor shall be hydraulic direct drive.
YES: ______
NO: ______
The main conveyor will be a minimum of 25" in width measured from the
outside to the outside of the convey or chain link.
YES: ______
NO: ______
To provide optimum safety and the lowest possible centre of gravity the
conveyor bed will measure a minimum of 33 ½" measured from side to
side
YES: ______
NO: ______
The unit must be capable of spreading and discharging “A” gravel via the
main conveyor, cross conveyor and spinner chute, without clogging,
jamming or other such problems and the manufacture will warranty the
unit as suitable for this operation and application.
YES: ______
NO: ______
Tender: 2018 Tandem Truck Cab & Chassis Complete with Plow Equipment
Closing Date: 4:00 p.m. June 15, 2017
The main conveyor cover will be manufacture from 3/16" Hardox 450
steel and will bolt into place for summer use.
YES: ______
NO: ______
The conveyor floor will be 1/4" Hardox 450 180,000 > 203,000 P.S.I.
YES: ______
NO: ______
Cross conveyor table to have extended poly guarding front and rear to
prevent material from falling onto hoist frame saddle and onto chassis
frame. Flush hose attachment for washing.
YES: ______
NO: ______
Cross conveyor table assembly to be prepped and painted Imron 5000
Elite SS Medium Gloss BLACK.
YES: ______
NO: ______
A polyurethane spinner and poly lined chute shall be installed on the left
hand side (driver side) to spread ahead of rear wheels.
YES: ______
NO: ____
Spinner disc will be hydraulic direct drive.
YES: ______
NO: ____
To provide a Grote 6" spinner light with switch in cab.
YES: ______
NO: ____
Anti-coning device on spinner assembly.
YES: ______
NO: ____
Fold down window salt chute for spinner assembly.
YES: ______
NO: ____
Swing up and lock horizontal storage position plus Safeway S70 dripless
quick couplers for ease of removal. Assembly to be square tube mounted
to chassis and round tube for spinner assembly – for ease of removal.
YES: ______
NO: ____
Spinner height shall be adjustable to accommodate various chassis
heights and capable of a discharge rate from 100 lbs./lane mile to 2,500
lbs./lane mile.
YES: ______
NO: ____
Bosch-Rexroth CS520 electronic spreader controller (2 section valve /
spinner and conveyors) supplied and installed below controls on swivel
pedestal between seats.
YES: ______
NO: ____
The regulator to be pressure compensated so that the selected flow will
not change as load or engine speed changes.
YES: ______
NO: ____
MP Filtri H.P. 10 Micron Absolute Filter Assembly
YES: ______
NO: ______
A by-pass switch to be provided to start or stop the spreader without
changing the settings.
YES: ______
NO: ____
YES: ______
NO: ____
6.
7.
8.
SPINNER
SANDER CONTROLS
FENDERS
Body mounted aluminum fenders pinned to underside of body to suit 56"
spread and to provide cover for wheels and protect body.
Tender: 2018 Tandem Truck Cab & Chassis Complete with Plow Equipment
Closing Date: 4:00 p.m. June 15, 2017
Mud flaps shall be provided fore and aft of rear wheels frame mounted.
Mudflaps not mounted to aluminum fenders.
YES: ______
NO: ____
The dump body shall be shot blasted and epoxy zinc primed.
YES: ______
NO: ____
Finish paint acrylic urethane - Imron 5000 Elite SS ‘Baked Finish”
YES: ______
NO: ______
Yellow match to Cab & Chassis. Dupoint N6661-HP Shell Yellow.
YES: ______
NO: ______
Top of integral steel body fenders including side rub rails and face of
rear body corner posts –to be Line X’d. colour coded to match body.
YES: ______
NO: ______
9.
10.
PAINT
LOAD COVER
An air tarp, mesh style shall be standard equipment with in cab switch,
dual air cylinders and 1 ½” x 1 ½” tubular steel dog legged tarp arms to
allow loader access. In-cab switch on floor pedestal.
YES: ______
NO: ______
Lights and wiring shall be completely sealed with corrosion and vapour
proof lamps and electrical junction boxes. Auxiliary relay box. All electrical
junction boxes to be mounted at B.O.C. above frame.
YES: ______
NO: ______
For improved rear visibility rear lamps to be rectangular mounted in rear
corner posts within 3" of the outside of the tailgate.
YES: ______
NO: ______
Light and Wiring kit shall be Grote Ultra blue seal only and include Grote
L.E.D. lights, junction box and wiring.
YES: ______
NO: ______
Grote 6" backup light at rear of body hooked into O.E.M reverse switch.
YES: ______
NO: ______
LED lights in rear corner posts of dump box shall be stop, turn, tail, backup
- 3 sets of lights each side.
YES: ______
NO: ______
Two raised detachable MTO upper body plug in aluminum light poles at
rear top corners of body to include stop, tail, directional, upper reads and
flashing blue and amber. Two Grote L.E.D. flood / spot lights - aimed at
ground – one light each tree - hooked into O.E.M. reverse switch.
YES: ______
NO: ______
4" amber and 4" blue LED strobe in stainless steel boxes, mounted at rear
of chassis frame with separate in cab switches.
YES: ______
NO: ______
Separate Amber and Blue Star 200A Strobe Lights mounted at front
behind cab on adjustable pole marked switches on cable pedestal.
YES: ______
NO: ______
Amber and Blue Grote strobe light each side of gate at top upper corners
of body.
YES: ______
NO: ______
All LED Blue strobe on separate switch
YES: ______
NO: ______
11.
LIGHTS AND WIRING
Tender: 2018 Tandem Truck Cab & Chassis Complete with Plow Equipment
Closing Date: 4:00 p.m. June 15, 2017
All LED Amber Strobe on separate switch
YES: ______
NO: ______
License plate mount and light up on rear body x-member – drivers side.
YES: ______
NO: ______
Note: All lighting and electrical add on circuits to be protected through H.D.
electronic solenoid in control box, key activated. Do not re-install O.E.M.
Tail Lights. Ship loose in truck cab.
YES: ______
NO: ______
12.
HYDRAULICS
All fittings, valves hoses and drive shaft shall be supplied and installed.
All hoses shall be equipped with swivels on both ends and be two wire, 3
½" bend rating, min. 4500>5300 PSI., -70̊ + 260 degree temperature
rated.
YES: ______
NO: ______
The hydraulic reservoir shall be 35 US Gallons minimum to supply
necessary oil supply. Reservoir must not interfere with the box
installation.
YES: ______
NO: ______
A sight temperature gauge to allow easy checking of the hydraulic oil level
in the reservoir shall be supplied.
YES: ______
NO: ______
The hydraulic controls in cab shall be designed to swivel and adjust on a
mounted pedestal. Under cab floor stiffener plate for swivel pedestal.
YES: ______
NO: ______
YES: ______
NO: ______
13. PINTLE HOOK
Heavy duty pintle hook plate rated >30,000 lb. MGTW with frame
reinforcing and 2 safety chain loops. Holland PH400AR11 100,000 lb.
MGTW ‘air’ cushioned hook installed at ____” lunette height (level ground
to bottom inside of hook. Hook to have separate in-cab control on floor
pedestal for air plunger. Install O.E.M. 7 wire electrical plug and Viking
switched out Traction Tech #9311 #9312 swing away glad hands into
face plate. Angle iron bracket over top of hook with small rubber flap to
prevent dirt building up on hook. Prep and paint pintle hook plate
assembly Imron 5000 Elite SS Medium Gloss BLACK.
Tender: 2018 Tandem Truck Cab & Chassis Complete with Plow Equipment
Closing Date: 4:00 p.m. June 15, 2017
SNOW PLOW TRUCK HARNESS
Viking VCL500T tilt harness.
Specify:_____________________
Hydraulic tilt front plow harness with in cab control functions.
YES: ______
NO: ______
Quick attach plow push frame pockets.
YES: ______
NO: ______
The design and construction of the truck harness shall be in
compliance with M.T.O. standard ES-401, or be of equivalent design
approved by M.T.O.
YES: ______
NO: ______
The harness shall be mounted at the front end of the frame and be
bolted to the compatible ½” cheek plates. Fasteners attaching cheek
plates to chassis frame rails will be minimum grade 8 N.C. hex head
bolts.
YES: ______
NO: ______
The lifting frame shall be bolted to the push plate and shall be braced
to conform with M.T.O. standards. Two mounting locations in lift
yoke cylinder – winter operation position and stored summer
position. Three grab links shall be supplied.
YES: ______
NO: ______
Lifting Ram Diameter - 4" D.A. minimum.
SPECIFY: __________________
Lifting Ram Stroke - shall be 10" minimum.
SPECIFY: __________________
The cylinder rod shall be fully chrome plated.
YES: ______
NO: ______
Drive ears shall be 30 ½ " centre to centre.
YES: ______
NO: ______
Height to lower drive connection shall be 19" when mounted, truck
empty.
YES: ______
NO: ______
Five grab links shall be supplied.
YES: ______
NO: ______
Male Coupler: male hinged swing arm and its enclosed rigid
mounting bracket shall form as integral assembly and is to be fitted
to the side cheek plate. The assembly remains permanently with the
vehicle even after the female coupler has been detached.
YES: ______
NO: ______
Tender: 2018 Tandem Truck Cab & Chassis Complete with Plow Equipment
Closing Date: 4:00 p.m. June 15, 2017
The swing arm is to be operated by two double acting hydraulic lock
/ unlock cylinders with remote controls at front drivers side corner of
chassis. Air control switches in steel enclosure for locking / unlocking
cylinder pins. Cylinders specifications: 2 ½” piston diameter, 1 1/8”
piston chromed piston rod diameter with 6” stroke.
YES: ______
NO: ______
All structural steel plate used in the plow harness will be 44W
complying with CSA G40.21.
YES: ______
NO: ______
Tensile strength will be 65-90 KSI and the minimum yield strength
will be 44 KSI.
YES: ______
NO: ______
Hydraulic quick coupler on angled manifold mounting plate at front
of truck to have Safeway S70 drip less quick couplers with plugs –
all lines to be colour tagged for ease of hook up.
YES: ______
NO: ______
Two sealed beams Halogen type headlamps with high and low beam
shall be supplied including twin signals with plow headlight relay
board and in-dash headlight switch.
YES: ______
NO: ______
Right front helper spring shall be provided. 5,000 lb. capacity Aeon
Rubber shall be used and shall be easily removable.
YES: ______
NO: ______
The plow lights and signals shall be equipped with“Quick-Tack”
ends.
YES: ______
NO: ______
All hydraulic hoses and wiring shall be adequately supported to
ensure that wear and sag is completely eliminated
YES: ______
NO: ______
The front plow harness shall tilt forward to allow the hood to tilt over
centre of its pivots and stay open without the need of any additional
supports.
YES: ______
NO: ______
The harness will be supplied with two double acting hydraulic
cylinders, one cylinder to perform the plow lift function and a second
separate cylinder used to perform the tilt function exclusively with in
cab control.
YES: ______
NO: ______
2 – Par 36 #64123 yellow fog lights with chrome bezels on top of
harness with in cab switch
YES: ______
NO: ______
The tilt cylinder will be 2 ½ " with a 6" stroke and the cylinder rod
shall be fully chromed.
YES: ______
NO: ______
Tender: 2018 Tandem Truck Cab & Chassis Complete with Plow Equipment
Closing Date: 4:00 p.m. June 15, 2017
License plate mount at top of harness – drivers side.
YES: ______
NO: ______
Harness assembly prepped and painted Imron 5000 Elite SS
Medium Gloss BLACK.
YES: ______
NO: ______
Front bumper to be cut and re-installed to chassis.
YES: ______
NO: ______
A parts manual shall be supplied with unit(s).
YES: ______
NO: ______
Tender: 2018 Tandem Truck Cab & Chassis Complete with Plow Equipment
Closing Date: 4:00 p.m. June 15, 2017
SNOW PLOW EQUIPMENT - 9' ONE WAY SNOW PLOW
VIKING VCL 135 HSE-9 or equivalent.
Specify:
______________________
This one way snow plow shall conform with the provisions of M.T.O.
standards ES-414, except that the dimensions of this specification
shall prevail when the two contradict.
YES: ______
NO: ______
The plow shall operate effectively and without modification with the
M.T.O. snow plow truck harness ES-401.
YES: ______
NO: ______
The weight of the plow shall range from 2,000 to 2,300 lbs. and shall
be constructed to prevent the accumulation of water in any area.
Specify: _________________
All ribs shall be of one piece construction 100% welded both sides of
the mouldboard. The top edge of the mouldboard shall be
manufactured of 2 ½ " x 2 ½ " angle iron and welded securely to the
ribs and mouldboard with a continuous bead. All other welds must
also be 100%.
YES: ______
NO: ______
Hydraulic tilt moldboard with angle rod indicator to include in-cab
tilting lever.
YES: ______
NO: ______
The mouldboard brace rod shall be adjustable for plow angles of 45
degree, 50 degree and 55 degree.
YES: ______
NO: ______
Holes in drive bars for push frame shall be 1 1/4 " diameter.
YES: ______
NO: ______
The height of the mouldboard at the top of curve shall be as follows:
Intake: 35" min.
Specify: ________________
Discharge: 64" min.
Specify: ________________
The overall length shall be 15'10" minimum.
Plow shall clear 10'3" @ 37.
Specify: ________________
Specify: ________________
Tender: 2018 Tandem Truck Cab & Chassis Complete with Plow Equipment
Closing Date: 4:00 p.m. June 15, 2017
There shall be eight vertical ribs, 3 ½ " high by 3/8" thick. Minimum
weld between the mouldboard and rib shall be 100% weld each side.
YES: ______
NO: ______
The bottom rail on the mouldboard shall be 5" x 3" x ½" angle below
with a 3" x 2" x 3/8" gussets shall be welded between the two legs of
the bottom angle, between each bolthole, except for the two sets of
end holes and between two holes in the middle of the mouldboard.
The mouldboard shall be continuously welded to the bottom rails.
YES: ______
NO: ______
Sleeved moldboard safety check cable shall be installed for plow to
push frame to prevent plow from going over center if moldboard pin
malfunctions
YES: ______
NO: ______
Fluorescent orange plow marker on each end of plow installed
YES: ______
NO: ______
12" x ½" rubber deflector bolted across mold board to be installed
YES: ______
NO: ______
Moldboard cutting edge to be CARBIDE tipped VBL VAL STRIP
hardened plate with nose piece and 3 plow edge shoes
YES: ______
NO: ______
Trip link safety mechanism shall be incorporated the blade
mechanism must return to the normal plowing position automatically.
Trip springs must be secured with lock nuts.
YES: ______
NO: ______
Two separate lift chains shall be used and these shall pick upon the
drive frame at points approximately 48" apart.
YES: ______
NO: ______
These lift chains shall be ½" dia. minimum. Grade 70
Specify: _______________
The height of the shoes shall be adjustable as shown on M.T.O. ES521. Height adjustable one way snow plow shoe holder.
YES: ______
NO: ______
The shoes shall oscillate.
YES: ______
NO: ______
The mouldboard shall be formed in the shape of a smooth curve no
breaks or formed bends.
YES: ______
NO: ______
A sturdy eye ½" thickness shall be provided at the centre of gravity
for handling of the mouldboard.
YES: ______
NO: ______
Quick attach swivel shall be supplied. Sleeved mold board check
cable.
YES: ______
NO: ______
The design and quality shall meet M.T.O. requirements.
YES: ______
NO: ______
Tender: 2018 Tandem Truck Cab & Chassis Complete with Plow Equipment
Closing Date: 4:00 p.m. June 15, 2017
The complete snow plow unit shall be prepped and painted Imron
5000 Elite SS Medium Gloss BLACK.
YES: ______
NO: ______
A spare parts manual shall be supplied.
YES: ______
NO: ______
A signed manufacturer’s warranty shall be supplied.
YES: ______
NO: ______
Tender: 2018 Tandem Truck Cab & Chassis Complete with Plow Equipment
Closing Date: 4:00 p.m. June 15, 2017
FRONT MOUNT PUMP
The hydraulic pump supplied shall be front mounted 90cc Sauer
Danfoss variable displacement pump with Bosch Rexroth AISV shut
off over ride function.
YES: ______ NO: ______
Pump mounting plate and splined, machined and balanced tube drive
shaft shall be supplied.
YES: ______
NO: ______
The pump shall be driven from the crankshaft.
YES: ______
NO: ______
The pump shall have a manufacturer’s R.P.M. rating equivalent or
higher than that of the truck engine at governed speed.
YES: ______
NO: ______
Hydraulic hoses to connect pump shall be supplied.
YES: ______
NO: ______
The drive shaft shall be supplied with spline long enough to allow
telescopic retraction of the shaft in order to change fan belt without
removing the pump.
YES: ______
NO: ______
The hydraulic system must be set up so all other hydraulic functions
do not “rob” the sander equipment.
YES: ______
NO: ______
A parts manual shall be supplied with each unit.
YES: ______
NO: ______
The control valve will include the following NINE sections:
1-D.A. Plow Lift
1-D.A. Hydraulic Tilt Moldboard Cylinder
1-D.A. Tilt Harness
1-D.A. Hydraulic Harness Lock Cylinder
1 D.A. Hydraulic Harness Unlock Cylinder
1-D.A. Front of Wing
1-D.A. Rear Wing Slide
1-D.A. Wing Braces
1-S.A. Body Hoist
YES: ______
NO: ____
Their size shall be adequate for quick operation of all hydraulic
operations and shall be 2 ply braided steel SAE100RS, with swivel
on both ends.
Tender: 2018 Tandem Truck Cab & Chassis Complete with Plow Equipment
Closing Date: 4:00 p.m. June 15, 2017
HYDRAULIC CONTROLS
The hydraulic controls valves will be operated by proportional
featherable in cab air controls.
YES: ______
NO: ____
The control panel assembly shall be of a remote design pedestal
mounted and adjustable.
YES: ______
NO: ____
An oil reservoir of adequate capacity shall be supplied complete with
oil filter level sight gauge, breather type filter cap, drain plug and oil
shut off valve.
YES: ______
NO: ____
The complete valve stack assembly will be mounted vertically on a
1/4" mounting plate, integral with the rear wing tower assembly.
YES: ______
NO: ____
The valve mounting plate will be welded to the horizontal channel and
sloping diagonal brace.
YES: ______
NO: ____
The valve assembly will be completely open and easily accessible
from the drivers side of the chassis for washing and maintenance and
to include a chromed override handle for valves at back of cab.
YES: ______
NO: ____
Tender: 2018 Tandem Truck Cab & Chassis Complete with Plow Equipment
Closing Date: 4:00 p.m. June 15, 2017
FRONT VIKING 8" VCL 350 SCL WING POST - WITH CABLE AND SHEAVES
MAKE AND MODEL
SPECIFY:
The design and construction of the wing post shall be in compliance
with MTO ES403, or shall be equivalent design approved by the MTO.
Brace "A" li ES403 shall be replaced by a second sturdy cross member.
This cross member shall be bolted to both cheek plates. Alternate
braces must be approved.
The wing post shall be made of 8" I-Beam, 18.4lb.ft. minimum. Cross
member shall be of heavy construction to sustain snow plowing
operation in severe conditions.
The sheave pin shall be provided with a grease fitting and an elite
bushing.
A safety stop, limited slide travel shall be supplied.
Lifting cable shall not be mounted to the hinge pin.
An 8"grab link shall be located halfway between upper and lower
position of bolt "D"as shown on ES403.
Front slide shall be provided with a tipover arrangement. A spring shall
be included to return the blade to normal position after it has tripped.
Front Slide to be 5/8"thick x 24"Long
Bottom of wing post shall be approx. 11" from the ground, truck empty,
and shall be protected by a shoe.
Specify:
_____________________
YES: ______
NO: ______
A 3"x 30"stroke D.A. cylinder shall be mounted on the inside of the front
post and shall operate the front wing slide.
YES: ______
NO: ______
Cross member must be bolted to wing post.
YES: ______
NO: ______
Tender: 2018 Tandem Truck Cab & Chassis Complete with Plow Equipment
Closing Date: 4:00 p.m. June 15, 2017
6"overhang shall be left on cross members to allow lateral
YES: ______
NO: ______
Guide bars for the slide shall be welded 100% up 2' from bottom
YES: ______
NO: ______
The wing post and cross member shall be painted gloss black
YES: ______
NO: ______
A parts manual shall be supplied with each unit.
YES: ______
NO: ______
Grote 12" #12020 convex mirror on 10" angle iron bracket shall be
mounted to back side of post to enable driver to view down the curbside
of the truck .
YES: ______
NO: ______
One 6" front post spot lights facing forward with separate marked
switches in cab on pedestal. Lights mounted on adjustable 16" pedestal.
YES: ______
NO: ____
Aeon auxiliary rubber helper kit installed to factory chassis springs on
curbside to aid in winging operation.
YES: ______ NO: ____
Hydraulic fittings to be "Safeway S70 Quick couplers" for case of
installing or removing wing.
YES: ______
movement for mounting the wing post on future trucks
NO: ____
Tender: 2018 Tandem Truck Cab & Chassis Complete with Plow Equipment
Closing Date: 4:00 p.m. June 15, 2017
VIKING VCL 350 SCL FULL HYDRAULIC SNOW PLOW WING TOWER
WITH CABLE AND SHEAVES
MAKE AND MODEL
SPECIFY:
Additional M.T.O. Cross member at rear of cab to be added by body YES: ______ NO: ____
builder to compensate for rear wing tower and hydraulics
The harness assembly shall be of heavy construction to sustain snow YES: ______ NO: ____
plowing operations under sever conditions.
A reservoir of adequate capacity shall be supplied but must not interfere YES: ______ NO: ____
with the operation of the box. Valves shall be installed on outlet lines at
reservoir.
Bottom of wing tower shall be protected by shoe and shall have a road YES: ______ NO: ____
clearance of 14" minimum, truck empty.
Approved size of ram controlling the front end of wing shall be 3" diameter YES: ______ NO: ____
x 30" stroke.
Approved size of ram controlling wing brace slide shall be 3" diameter x YES: ______ NO: ____
36" stroke approximately and shall be double acting.
Brace slide to be 3/4" thick x 24" long.
SPECIFY:_______________
________________________
________________
6" sealed beam wing light shall be provided with separate marked switch YES: ______ NO: ____
inside cab.
Wing tower shall be painted gloss black.
YES: ______ NO: ____
The wing tower shall be of 10" channel construction with a 25 degree YES: ______ NO: ____
onset and its mountings shall be sufficient to sustain snow plowing
operations under severe conditions.
One piece brace 2 3/4" diameter shall connect the bottom of the wing YES: ______ NO: ____
tower and the truck chassis near the forward mount of the right rear
springs to reduce the shock of the truck frame.
The rear wing tower shall be heavily braced and gusseted to the frame YES: ______ NO: ____
cheek plate.
Hydraulic hoses shall connect the rams of the tower with the valves in the YES: ______ NO: ____
control box. Hoses shall be two ply braided steel, SAE100R2 with swivels
on both ends.
A safety chain shall be provided for securing wing when not in use.
YES: ______ NO: ____
Tender: 2018 Tandem Truck Cab & Chassis Complete with Plow Equipment
Closing Date: 4:00 p.m. June 15, 2017
Guide bars to contain the rear wing slide shall be welded 100% in front of YES: ______ NO: ____
the bottom up 2 feet.
Parts manual shall be supplied with each unit.
YES: ______ NO: ____
Tender: 2018 Tandem Truck Cab & Chassis Complete with Plow Equipment
Closing Date: 4:00 p.m. June 15, 2017
SPECIFICATION FOR SNOW PLOWING EQUIPMENT
13' SNOW LEVELLING WING
Viking VCL156AHW 3/16” smooth paneled wing with no ribs.
Specify:
The snow leveling wing shall comply with the provisions of M.T.O. ES406, except for the length which is designated by the specification.
YES: ______
NO: ____
The inside height of the wing shall be 29" minimum.
YES: ______
NO: ____
The outside height of the wing shall be 39" minimum.
YES: ______
NO: ____
Overall length of the wing shall be 13 feet.
YES: ______
NO: ____
The plate for mounting the wing to the wing post shall be 1" thick. The
mounting hole shall be far enough from the edge of the plate to avoid
failure in this area.
YES: ______
NO: ____
The mounting of the nose end of the wing to the wing post shall be by
means of a hinges and retractable spring, to allow tipping over the wing.
YES: ______
NO: ____
Two adjustable wing braces shall be supplied.
YES: ______
NO: ____
The upper brace shall be of a shock release type, including a spring
retraction. The spring shall provide adequate stability of the wing in
normal operation conditions, and shall retract the wing from tip-over
position.
YES: ______
NO: ____
A 36" fluorescent orange marker on discharge end of wing.
YES: ______
NO: ____
One spare pin for adjusting the wing braces shall be supplied with each
brace.
YES: ______
NO: ____
The wing shall be fitted with the following:
YES: ______
NO: ____
One wing shoe M.T.O. ES-409
YES: ______
NO: ____
The wing shall be prepped and painted Imron 5000 Elite SS Medium
Gloss BLACK.
YES: ______
NO: ____
A parts manual shall be supplied with each unit.
YES: ______
NO: ____
One snow plow blade M.T.O. ES-504 - High Wearing
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement