Barcode positioning system BPS 34 for the

Barcode positioning system BPS 34 for the
Leuze electronic
Barcode positioning system BPS 34
for the PROFIBUS DP
Technical Description
© All rights reserved, especially the right of reproduction and translation.
This document may not be duplicated or reproduced in any form without the written permission of
Leuze electronic GmbH + Co. KG
It is subject to changes due to technical progress.
Leuze electronic
Table of contents
1
General information ........................................................................................................... 3
1.1
1.2
1.3
Explanation of symbols ........................................................................................................ 3
Declaration of conformity ..................................................................................................... 3
Description of the BPS 34 functions .................................................................................... 4
2
Safety notices..................................................................................................................... 5
2.1
2.2
2.3
2.4
General safety notices ......................................................................................................... 5
Safety standards .................................................................................................................. 5
Intended use ........................................................................................................................ 5
Working safely ..................................................................................................................... 6
3
Commissioning steps at a glance .................................................................................... 8
4
Specifications BPS 34 ..................................................................................................... 13
4.1
4.2
4.3
General specifications BPS 34 .......................................................................................... 13
Dimensioned drawings....................................................................................................... 14
Electrical connection .......................................................................................................... 16
4.3.1
4.3.2
4.3.3
4.3.4
4.3.5
PWR IN - voltage supply and switching input/output ................................................................... 18
DP IN - PROFIBUS DP incoming ................................................................................................ 19
DP OUT - PROFIBUS DP outgoing............................................................................................. 19
SW IN/OUT - switching input/switching output ............................................................................ 20
BPS 34 reading field curve .......................................................................................................... 21
5
Connector units MS 34 … / MSD 1 101........................................................................... 22
5.1
Modular hoods with integrated connectors MS 34 103 and MS 34 105 ............................ 22
5.1.1
5.1.2
5.1.3
5.1.4
5.1.5
General information ..................................................................................................................... 22
Specifications of the connector units ........................................................................................... 22
Dimensioned drawings ................................................................................................................ 23
Electrical connection.................................................................................................................... 24
Description of the LED states ...................................................................................................... 24
5.2
Modular Service Display MSD 1 101 ................................................................................. 25
5.2.1
5.2.2
5.2.3
General information ..................................................................................................................... 25
Dimensioned drawing .................................................................................................................. 26
Electrical connection.................................................................................................................... 26
6
Barcode tape .................................................................................................................... 27
6.1
6.2
6.3
6.4
General information ........................................................................................................... 27
Specifications of the barcode tape ..................................................................................... 28
Mounting the barcode tape ................................................................................................ 29
Control barcode ................................................................................................................. 32
6.4.1
Controllable functions .................................................................................................................. 33
6.5
Repair kit ............................................................................................................................ 35
7
Mounting ........................................................................................................................... 37
7.1
7.2
7.3
Mounting the BPS 34 ......................................................................................................... 37
Device arrangement........................................................................................................... 40
Mounting the barcode tape ................................................................................................ 41
Leuze electronic
BPS 34
1
Leuze electronic
Table of contents
8
Device parameters and interfaces.................................................................................. 42
8.1
PROFIBUS......................................................................................................................... 42
8.1.1
8.1.2
8.1.3
8.1.4
8.1.5
8.1.6
8.1.7
General information......................................................................................................................42
Electrical connection ....................................................................................................................42
PROFIBUS address .....................................................................................................................45
General information on the GSE file ............................................................................................45
Structure of the GSE modules .....................................................................................................46
Overview of the GSE modules .....................................................................................................47
Detailed description of the modules .............................................................................................50
9
Diagnostics and troubleshooting................................................................................... 92
9.1
9.2
General causes of errors ................................................................................................... 92
PROFIBUS errors .............................................................................................................. 92
10
Type overview and accessories ..................................................................................... 94
10.1
10.2
10.3
10.4
10.5
10.6
10.7
Type overview: BPS 34...................................................................................................... 94
Accessory modular hoods with integrated connectors....................................................... 94
Accessory modular service display.................................................................................... 94
Accessory termination........................................................................................................ 94
Accessory connectors........................................................................................................ 94
Accessory mounting device ............................................................................................... 94
Accessory ready-made cables for voltage supply.............................................................. 95
10.7.1
10.7.2
10.7.3
Contact assignment of PWR IN connection cable........................................................................95
Specifications of voltage supply cable .........................................................................................95
Order codes for voltage supply cables .........................................................................................95
10.8
Accessory ready-made cables for PROFIBUS connection................................................ 96
10.8.1
10.8.2
10.8.3
10.8.4
General ........................................................................................................................................96
Contact assignment for PROFIBUS connection cable KB PB…..................................................96
Specifications of PROFIBUS connection cable............................................................................97
Order codes for PROFIBUS connection cables ...........................................................................97
10.9
Type overview: Barcode tape ............................................................................................ 98
11
Maintenance ..................................................................................................................... 99
11.1
11.2
11.3
General maintenance information...................................................................................... 99
Repairs, servicing .............................................................................................................. 99
Disassembling, packing, disposing .................................................................................... 99
12
Appendix......................................................................................................................... 100
12.1
EU Declaration of Conformity .......................................................................................... 100
2
BPS 34
Leuze electronic
Leuze electronic
1
General information
1.1
Explanation of symbols
General information
The symbols used in this operating manual are explained below.
Attention!
This symbol appears before text passages which must absolutely be observed. Failure to
heed this information can lead to injuries to personnel or damage to the equipment.
Attention Laser!
This symbol warns of possible danger through hazardous laser radiation.
Notice!
This symbol indicates text passages containing important information.
Declaration of conformity
The barcode positioning system BPS 34, the modular hood with integrated connectors
MS 34 103/MS 34 105, and the optional modular service display MSD 1 101 have been
developed and manufactured under observation of the applicable European standards and
directives.
The devices of the BPS 34 series also fulfil the cUL requirements (Underwriters Laboratory
Inc.) for the USA and Canada.
Notice!
A copy of all declarations of conformity available for the product can be found in the appendix of this handbook (see chapter 12.1 "EU Declaration of Conformity" on page 100).
The manufacturer of the product, Leuze electronic GmbH + Co. KG in D-73277 Owen/Teck,
possesses a certified quality assurance system in accordance with ISO 9001.
C
UL
US
LISTED
Leuze electronic
BPS 34
3
TNT 35/7-24V
1.2
Leuze electronic
General information
1.3
Description of the BPS 34 functions
The BPS 34 uses visible red laser light to determine its position relative to the barcode tape.
This essentially takes place in three steps:
1.
Reading a code on the barcode tape
2.
Determining the position of the read code in the scanning area of the scanning beam
3.
Calculating the position to within a millimetre using the code information and the code
position relative to the device's centre.
The position value is then output via the interface.
4
BPS 34
Leuze electronic
Leuze electronic
2
Safety notices
2.1
General safety notices
Safety notices
Documentation
All entries in this technical description must be heeded, in particular those in section "Safety
notices". Keep this technical description in a safe place. It should be accessible at all times.
Safety regulations
Observe the locally applicable legal regulations and the rules of the employer's liability insurance association.
Repair
Repairs must only be carried out by the manufacturer or an authorised representative.
2.2
Safety standards
The devices of the BPS 34 series were developed, manufactured and tested in accordance
with the applicable safety standards. They correspond to the state of the art.
Intended use
Barcode positioning systems of the BPS 34 series are optical measuring systems which use
visible red laser light to determine the position of the BPS relative to a permanently mounted
barcode tape.
The modular hoods with integrated connectors MS 34 103/MS 34 105 are intended for the
easy connection of barcode positioning systems of type BPS 34 in a PROFIBUS system.
The modular service display MSD 1 101, which is optionally available, displays operational
data of the BPS 34 and is used as a simple means of access to the service interface of the
MS 34 105.
In particular, unauthorised uses include:
• rooms with explosive atmospheres
• operation for medical purposes
Attention!
The protection of personnel and the device is guaranteed only if the device is operated in a
manner corresponding to its intended use.
Leuze electronic
BPS 34
5
TNT 35/7-24V
2.3
Leuze electronic
Safety notices
Areas of application
The barcode positioning system BPS 34 has been developed for positioning tasks in the
following areas of application:
•
•
•
•
•
2.4
High-bay storage devices: Positioning in the travel and lifting axes
Crane bridges and trolleys
Side-tracking skates
Telpher lines
Lifts
Working safely
Attention!
Access to or changes on the device, except where expressly described in this operating
manual, are not authorised.
Safety Regulations
Observe the locally applicable legal regulations and the rules of the employer's liability insurance association.
Qualified personnel
Mounting, commissioning and maintenance of the device may only be carried out by qualified personnel.
Electrical work must be carried out by a certified electrician.
Attention, laser radiation!
Warning: The barcode positioning system BPS 34 operates with a red light laser of
class 2 acc. to EN 60825-1. If you look into the beam path over a longer time period,
the retina of your eye may be damaged!
Never look directly into the beam path!
Do not point the laser beam of the BPS 34 at persons!
When mounting and aligning the BPS 34, take care to avoid reflections of the laser
beam off reflective surfaces!
Heed the laser safety regulations according to DIN EN 60825-1 in their most current
version! The output power of the laser beam at the reading window is at most 1.8 mW
acc. to EN 60825-1.
The BPS 34 uses a laser diode with low power in the visible red light range with an
emitted wavelength of 650 … 690 nm.
Attention!
CAUTION! The use of operating and adjusting devices other than those specified here
or carrying out of differing procedures may lead to dangerous exposure to radiation!
6
BPS 34
Leuze electronic
Leuze electronic
Safety notices
The barcode positioning system BPS 34 is provided with the following warning notices on
the housing, as well as below and next to the reading window:
B
A
C
AVOID EXPOSURE- LASER LIGHT
IS EMITTED FROM THIS APERTURE
CAUTION: LASER LIGHT IF OPEN
DO NOT STARE INTO BEAM
D
TNT 35/7-24V
LASER LIGHT
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
Maximum output:
1.8 mW
Pulse duration:
120 µs
Emitted wavelength: 650 … 690 nm
IEC 60825-1:1993 + A2:2001
Complies with 21 CFR 1040.10 and 1040.11
except for deviations pursuant to
Laser Notice No. 50, dated July 2001
I
A
B
C
D
I
Hazard warning & logotype
Aperture label
Non-interlocked protective housing label
Warning label and certification label
Name plate
Figure 2.1: Attachment of the sticky labels with warning notices at the BPS 34
Leuze electronic
BPS 34
7
Leuze electronic
Commissioning steps at a glance
3
Commissioning steps at a glance
Notice!
Below you will find a short description for the initial commissioning of the barcode positioning system BPS 34. Detailed explanations for all listed points can be found throughout
the handbook.
➀
Mechanical design
Mounting the barcode tape
The barcode tape is to be affixed without tension to a dust- and grease-free mounting
surface.
➔ chapter 6.3 on page 29
Mounting the BPS 34 device
There are two different types of mounting arrangements for the BPS 34:
1.
Using 4 M4x6 screws on the rear of the device.
2.
Using a mounting device (BT 56) on the dovetail fastening grooves.
Notice!
The installation dimensions listed in the following figure must absolutely be adhered to. Optically, it must be ensured that the scanner has an unobstructed view of the barcode tape at
all times. ➔ chapter 7.2 on page 40
Centre of the scanning beam
(device centre, output position value)
Barcode tape
Scanning beam
10˚
000204
000208
0002122
000216
Beam exit
10˚
10 ° pitch
in the vertical
axis
(dependent on
the tape height,
see notice)
Read distance
all dimensions
in mm
Figure 3.1:
103 ± 2
0002000
Beam exit and device arrangement of the BPS 34
➔ chapter 7.1 on page 37
8
BPS 34
Leuze electronic
Leuze electronic
Commissioning steps at a glance
Notice!
During mounting, the following angles of inclination must be taken into account in the vertical
axis:
10 ° for a tape height of 47 mm,
7 ° for a tape height of 30 mm and
5 ° for a tape height of 25 mm; the working range of the reading field curve must also be taken into account.
Attention!
For the position calculation, the scanning beam of the BPS 34 must be incident on the barcode tape without interruption. Ensure that the scanning beam is always incident on the barcode tape when the system is moving.
➁
Connecting the voltage supply and PROFIBUS
The BPS 34, in combination with an MS 34 103 or MS 34 105, is connected via M12
connectors.
Connecting the voltage supply
The voltage supply is connected via the PWR IN M 12 connection.
Socket
(A-coded)
Socket
(A-coded)
MSD
SW IN/OUT
/SERV 1
DP OUT
GND
7
A (N)
2
VCC 1
3 GND
4
PE
B (P)
Socket
(B-coded)
Figure 3.2:
Leuze electronic
SWOUT
2
TXD
3
4
6
SDA
5
RXD
SCL
3 GND
VOUT 1
4
SWIN
DP IN
A (N)
2
GND 3
1 VCC
4
B (P)
PE
PE
TNT 35/7-24V
VIN
2
/INT
PWR IN
SWOUT
2
GND 3
PE
Plug
(B-coded)
1 VIN
4
SWIN
Plug
(A-coded)
BPS 34 with MS 34 103/MS 34 105 - Connection PWR IN
BPS 34
9
Leuze electronic
Commissioning steps at a glance
Connecting the PROFIBUS
The PROFIBUS is connected via DP IN or, in the case of a continuing network, via DP OUT.
If DP OUT is not used, the PROFIBUS must be terminated at this point with an M 12 terminator plug (see chapter 10.4 "Accessory termination").
Socket
(A-coded)
Socket
(A-coded)
MSD
SW IN/OUT
VIN
2
/INT
/SERV 1
DP OUT
GND
7
A (N)
2
VCC 1
3 GND
RXD
4
6
SDA
5
SCL
4
SWIN
DP IN
GND 3
PE
PWR IN
SWOUT
2
GND 3
1 VCC
4
B (P)
PE
Socket
(B-coded)
3 GND
VOUT 1
A (N)
2
4
PE
B (P)
Figure 3.3:
SWOUT
2
TXD
3
PE
Plug
(B-coded)
1 VIN
4
SWIN
Plug
(A-coded)
BPS 34 with MS 34 103/MS 34 105 - Connections DP IN and DP OUT
Setting the PROFIBUS address
The PROFIBUS address must be set in the MS 34 10x connector plug hood. The correct
address setting on the PROFIBUS network is indicated by the green LED on the MS 34 10x.
Slide switch for the hundreds (marked with 102)
Rotary switch for the tens (marked with 101)
Rotary switch for the single digits (marked with 100)
Position of the slide
switch:
Top
address
100 - 126
Bottom
address
1 - 99
Connector to the BPS 34
Figure 3.4:
10
View of the inside of the MS 34
BPS 34
Leuze electronic
Leuze electronic
Commissioning steps at a glance
PROFIBUS manager
Install the GSE file associated with the BPS 34… in the PROFIBUS manager of your control.
Activate the desired modules (at least module 1 - position value).
Figure 3.5:
Example PROFIBUS manager
Store the slave address for the BPS 34 in the PROFIBUS manager. Ensure that the address
is the same as the address configured in the device.
The switching input/switching output is connected via SW IN/OUT.
Socket
(A-coded)
Socket
(A-coded)
MSD
SW IN/OUT
VIN
2
/INT
DP OUT
GND
7
A (N)
2
VCC 1
3 GND
4
PE
B (P)
Socket
(B-coded)
Figure 3.6:
Leuze electronic
SWOUT
2
TXD
3
/SERV 1
4
6
SDA
5
TNT 35/7-24V
➂
Connecting the switching input/switching output at the BPS 34
RXD
SCL
3 GND
VOUT 1
4
SWIN
DP IN
A (N)
2
GND 3
1 VCC
4
B (P)
PE
Plug
(B-coded)
PE
PWR IN
SWOUT
2
GND 3
1 VIN
4
SWIN
PE
Plug
(A-coded)
BPS 34 with MS 34 103/MS 34 105 - Connection SW IN/OUT
BPS 34
11
Leuze electronic
Commissioning steps at a glance
➃
Connecting the Modular Service Display MSD 1 101
The MSD 1 101 is connected via cable KB 034-2000 (M12 connection on MSD and M12
connection on MSD 1 101, see chapter 10.3 "Accessory modular service display" on
page 94).
Socket
(A-coded)
Socket
(A-coded)
MSD
SW IN/OUT
VIN
2
/INT
/SERV 1
DP OUT
GND
7
A (N)
2
VCC 1
3 GND
4
PE
B (P)
Socket
(B-coded)
SWOUT
2
TXD
3
4
6
SDA
5
RXD
SCL
3 GND
VOUT 1
4
SWIN
DP IN
A (N)
2
GND 3
1 VCC
4
B (P)
PE
Plug
(B-coded)
PE
PWR IN
SWOUT
2
GND 3
1 VIN
4
SWIN
PE
Plug
(A-coded)
Figure 3.7:BPS 34 with MS 34 103/MS 34 105 - Connection MSD
The BPS 34 can be accessed via the MS 1 101 using the service interface.
Notice!
Changes which were made via the service interface on the BPS 34 are lost following initialisation on the PROFIBUS.
12
BPS 34
Leuze electronic
Leuze electronic
Specifications BPS 34
4
Specifications BPS 34
4.1
General specifications BPS 34
Measurement data
Reproducible accuracy
Integration time
Measurement value output
Working range
Max. traverse rate
Electrical data
Interface type
Service interface
Switching input / output
LED green
Operating voltage
Power consumption
Mechanical data
Protection class
Weight
Dimensions (W x H x D)
Housing
Laser diode 650 nm
by means of rotating polygon mirror wheel
see reading field (figure 4.3.5)
glass with scratch-resistant Indium coating
2 acc. to EN 60825-1 1),
II acc. to CDRH (U.S. 21 CFR 1040.10 and 1040.11)
±1 (2) mm
16 (8) ms
2 ms (500 values/s)
90 … 170 mm
10 m/s
PROFIBUS DP, up to 12 MBd
RS 232 with default data format
9600 Bd, 8 data bits, no parity, 1 stop bit
1 switching input, 1 switching output, each is programmable
device ready (power on) and bus O.K.
without optics heating: 10 … 30 V DC
with optics heating:
22 … 26 V DC 2)
without optics heating: 5 W
with optics heating:
max. 30 W
IP 653)
without optics heating:
with optics heating:
without optics heating:
with optics heating:
diecast aluminium
400 g
480 g
120 x 90 x 43 mm
120 x 90 x 52 mm
Environmental data
Operating temperature range without optics heating:
0 °C … +40 °C
with optics heating:
-30 °C … +40 °C
High temperature version:
0 °C … +50 °C
Storage temperature range
-20 °C … +60 °C
Air humidity
max. 90 % rel. humidity, non-condensing
Vibration
IEC 60068-2-6, test FC
Shock
IEC 60068-2-27, test Ea
Continuous shock
IEC 60068-2-29, test Eb
Electromagnetic compatibility EN 55022, EN 55024, EN 61000-4-2, -3, -4 and -6,
EN 61000-6-2 and -3 1)
Leuze electronic
BPS 34
13
TNT 35/7-24V
Optical data
Light source
Beam deflection
Reading distance
Optical window
Laser safety class
Leuze electronic
Specifications BPS 34
Barcode tape
Max. length
(measurement length)
Ambient temperature
Mech. properties
1)
2)
3)
10000 m
-40 °C … +120 °C
scratch and wipe resistant, UV resistant,
moisture resistant, partly chemical resistant
For details see Declaration of Conformity on page 100
To ensure constant heat emission
With MS 34 10x plugged in and M12 connectors/caps screwed into place
Table 4.1:
General specifications
Notice!
The warm-up time before devices with integrated heating are ready for operation is approx.
30 min. (depending on the environmental conditions).
For devices with integrated heating (…H models), window heating is in constant operation.
Regulation of device-internal heating is temperature dependent.
4.2
Dimensioned drawings
BPS 34 SM 100 / BPS 34 SM 100 H / BPS 34 SM 100 HT
Rear view
Plan view
(without heating)
Plan view
(with heating)
All dimensions in mm
Figure 4.1:
14
Dimensioned drawing BPS 34
BPS 34
Leuze electronic
Leuze electronic
Specifications BPS 34
MS 34 103 / MS 34 105
MS 34 105
Notice!
The MSD and SW IN/OUT
connections are sealed with caps
upon delivery.
A = BPS 34
All dimensions in mm
Figure 4.2:Dimensioned drawing MS 34 103 / MS 34 105
Leuze electronic
BPS 34
15
TNT 35/7-24V
MS 34 103
Leuze electronic
Specifications BPS 34
4.3
Electrical connection
The BPS 34 can be connected via the MS 34 103/MS 34 105 using M12 connectors. For the
locations of the individual device connections, please refer to the device detail shown in
figure 4.3.
The corresponding mating connectors and ready-made cables are available as accessories
for all connections. For additional information, refer to chapter 10 starting on page 94.
Attention!
Connection of the device and cleaning must only be carried out by a qualified electrician.
If faults cannot be corrected, the device should be removed from operation and protected
against possible use.
Before connecting the device, be sure that the supply voltage agrees with the value printed
on the name plate.
The power supply unit for the generation of the supply voltage for the BPS 34 and the respective connection units must have a secure electrical insulation through double insulation
and safety transformers according to EN 60742 (corresponds to IEC 60742).
Be sure that the protective conductor is connected correctly. Error-free operation is only
guaranteed if the device is properly earthed.
16
BPS 34
Leuze electronic
Leuze electronic
PWR IN
DP IN
DP OUT
MSD
SW IN/OUT
Specifications BPS 34
= voltage supply
= PROFIBUS IN
= PROFIBUS OUT
= Modular Service Display (MS 34 105 only)
= switching input/output (MS 34 105 only)
All dimensions in mm
Notice!
The MSD and SW IN/OUT
connections are sealed with caps upon delivery.
Socket
(A-coded)
Socket
(A-coded)
MSD
SW IN/OUT
/SERV 1
DP OUT
GND
7
A (N)
2
VCC 1
3 GND
4
PE
B (P)
Socket
(B-coded)
SWOUT
2
TXD
3
4
6
SDA
5
RXD
SCL
3 GND
VOUT 1
4
SWIN
DP IN
A (N)
2
GND 3
1 VCC
4
B (P)
PE
Plug
(B-coded)
PE
TNT 35/7-24V
VIN
2
/INT
PWR IN
SWOUT
2
GND 3
PE
1 VIN
4
SWIN
Plug
(A-coded)
Figure 4.3:Connection assignment of the BPS 34 with MS 34 103 / MS 34 105
Attention!
Protection class IP 65 is achieved only if the connectors and caps are screwed into place!
Leuze electronic
BPS 34
17
Leuze electronic
Specifications BPS 34
4.3.1
PWR IN - voltage supply and switching input/output
Attention!
For devices with integrated heating, the supply voltage must be wired with a minimum
0.5 mm² (recommended 0.75 mm²) core cross section. It is not possible to loop the
supply voltage through to other loads!
Notice!
Cables with a core cross section of 0.5 mm² or 0.75 mm² are not available as ready-made
cables from Leuze electronic.
PWR IN (5-pin plug, A-coded)
Pin
PWR IN
SWOUT
2
GND 3
PE
M 12 plug
(A-coded)
Figure 4.4:
1
1 VIN
4
SWIN
Name
VIN
2
Remark
Positive supply voltage
without optics heating: +10 … +30 V DC
with optics heating: +22 … +26 V DC
SWOUT Switching output
3
GND
Negative supply voltage 0 V DC
4
SWIN
Switching input
5
PE
Functional earth
Thread
PE
Functional earth (housing)
Pin assignment PWR IN
Connection of the functional earth PE
BPS 34 including hood with integrated connectors MS 34 103/MS 34 105:
! Connect PE to PIN 5 of the M 12 connector PWR IN for the voltage supply!
Notice!
Programming of the switching input/switching output is performed via module 7 (Switching
input) and module 8 (Switching output). For further information, see also chapter 8.1.7.7,
page 59 ff.
Notice!
The switching input/switching output of the PWR IN plug connection is identical to the SWIN
switching input and SWOUT switching output of the SW IN/OUT plug connection on the
MS 34 105.
Attention!
Protection class IP 65 is achieved only if the connectors and caps are screwed into place!
18
BPS 34
Leuze electronic
Leuze electronic
4.3.2
Specifications BPS 34
DP IN - PROFIBUS DP incoming
DP IN (5-pin plug, B-coded)
Pin
DP IN
A (N)
2
GND 3
PE
1 VCC
4
B (P)
M 12 plug
(B-coded)
Figure 4.5:
Name
Remark
1
VCC
5 V DC for bus termination
2
A (N)
Receive/transmit data A-line (N)
3
GND
Functional earth for bus termination
4
B (P)
Receive/transmit data B-line (P)
5
PE
Functional earth
Thread
PE
Functional earth (housing)
Pin assignment DP IN
Attention!
Protection class IP 65 is achieved only if the connectors and caps are screwed into place!
4.3.3
DP OUT - PROFIBUS DP outgoing
DPOUT (5-pin socket, B-coded)
A (N)
2
VCC 1
3 GND
4
PE
B (P)
M 12 socket
(B-coded)
Figure 4.6:
Pin
Name
1
VCC
5 V DC for bus termination
Remark
2
A (N)
Receive/transmit data A-line (N)
3
GND
Functional earth for bus termination
4
B (P)
Receive/transmit data B-line (P)
5
PE
Functional earth
Thread
PE
Functional earth (housing)
TNT 35/7-24V
DP OUT
Pin assignment DP IN
Attention!
Protection class IP 65 is achieved only if the connectors and caps are screwed into place!
Notice!
If the PROFIBUS is not connected to another subscriber via the MS 34 10x, the DP OUT
connection must be fitted with a TS 02-4-SA terminator plug for the purpose of bus termination. For further information, see also chapter 10.4 on page 94.
Leuze electronic
BPS 34
19
Leuze electronic
Specifications BPS 34
4.3.4
SW IN/OUT - switching input/switching output
SW IN/OUT (5-pin socket, A-coded)
Pin
Name
1
VOUT
SW IN/OUT
SWOUT
2
3 GND
VOUT 1
4
SWIN
M 12 socket
(A-coded)
Figure 4.7:
PE
2
Remark
Supply voltage for sensors
(VOUT identical to VIN at PWR IN)
without optics heating: +10 … +30 V DC
with optics heating: +22 … +26 V DC
SWOUT Switching output
3
GND
Supply voltage for sensors 0 V DC
4
SWIN
Switching input
5
PE
Functional earth
Thread
PE
Functional earth (housing)
Pin assignment SW IN/OUT
Attention!
Protection class IP 65 is achieved only if the connectors and caps are screwed into place!
Notice!
Programming of the switching input/switching output is performed via module 7 (Switching
input) and module 8 (Switching output). For further information, see also chapter 8.1.7.7,
page 59 ff.
Notice!
The switching input/switching output of the PWR IN plug connection is identical to the SWIN
switching input and SWOUT switching output of the SW IN/OUT plug connection on the
MS 34 105.
Attention!
If you use a sensor with a standard M 12 connector, then please note the following:
Only use sensors on which the switching output does not lie on pin 2, i.e. only sensor cables
on which pin 2 is not assigned. Otherwise, the switching output is not protected against feedback on the switching input. If the inverted sensor output lies on pin 2, erroneous behaviour
of the switching output will result!
20
BPS 34
Leuze electronic
Leuze electronic
Specifications BPS 34
Connecting the switching input / switching output
The BPS 34 is provided with a switching input and a switching output. The connection is
performed as shown in figure 4.8:
Connector SW IN/OUT
4
SWIN
1
V OUT
2
SW OUT
3
GND
5
PE
1
V IN
3
GND IN
A
Sensor
max.
100 mA
Connector PWR
Figure 4.8:Connection of the switching input/output of the BPS 34
4.3.5
BPS 34 reading field curve
80
TNT 35/7-24V
60
Reading field width [mm]
40
20
Working range of
the BPS 34
0
-20
-40
-60
-80
0
25
50
75
90 100
125
150
170 175
200
225
250
Read distance [mm]
Figure 4.9:
Leuze electronic
BPS 34 reading field curve
BPS 34
21
Connector units MS 34 … / MSD 1 101
Leuze electronic
5
Connector units MS 34 … / MSD 1 101
5.1
Modular hoods with integrated connectors MS 34 103 and MS 34 105
A modular hood of type MS 34 103 or MS 34 105 with integrated connectors is part of every
BPS 34. The two hoods with integrated connectors are used to connect the BPS 34 to the
PROFIBUS. For this, they feature one DP IN and one DP OUT connection each, as well as
switches for address setting.
If only the connection to the PROFIBUS is intended, type MS 34 103 is sufficient.
If, in addition, switching input/output or a modular service display are to be connected, an
MS 34 105 is required. Although switching input and output are available on the voltage
supply connector PWR IN, the switching input of the MS 34 105 has the advantage that a
standard sensor connector can be used.
5.1.1
General information
The modular hoods with integrated connectors are necessary accessories for connecting a
BPS 34 in a PROFIBUS system. On the MS 34 10x, the PROFIBUS is connected, the
PROFIBUS address set and the BPS 34 supplied with voltage.
MS 34 103
The MS 34 103 offers the following interfaces:
• PROFIBUS incoming DP IN
• PROFIBUS outgoing DP OUT
• Voltage supply PWR IN with switching input and switching output
MS 34 105
In addition to the MS 34 103, the MS 34 105 offers the following interfaces:
• for the modular service display MSD
• M 12 connection for switching input and switching output SW IN/OUT
5.1.2
Specifications of the connector units
Mechanical data
Protection class
Weight
Dimensions (W x H x D)
Housing
1)
22
IP 65 1)
160 g
38 x 90 x 39 mm
diecast zinc
with M12 connectors/caps screwed into place
BPS 34
Leuze electronic
Leuze electronic
Dimensioned drawings
MS 34 103
MS 34 105
A = BPS 34
Notice!
The MSD and SW IN/OUT
connections are sealed with caps
upon delivery.
All dimensions in mm
Figure 5.1:Dimensioned drawing MS 34 103 / MS 34 105
Leuze electronic
BPS 34
23
TNT 35/7-24V
5.1.3
Connector units MS 34 … / MSD 1 101
Connector units MS 34 … / MSD 1 101
5.1.4
Electrical connection
Electrical data
Interface type
Service interface1)
PROFIBUS DP, up to 12 MBd
RS232 with default data format,
9600 Bd, 8 data bits, no parity, 1 stop bit
1 switching input, 1 switching output, each is programmable
without optics heating:
10 … 30 V DC
with optics heating:
22 … 26 V DC
without optics heating:
5W
with optics heating:
max. 30 W
Switching input / output
Operating voltage
Power consumption
1)
5.1.5
Leuze electronic
Only in combination with the MS 34 105 and MSD 1 101 devices
Description of the LED states
MS 34 103 / MS 34 105
At the modular hood with integrated connectors a status LED is located between the M 12
connectors DP IN and DP OUT. It indicates the state of the PROFIBUS connection.
State
Meaning
off
voltage off or device not yet recognised by the PROFIBUS 2)
green flashing
initialisation of the device, establishing the PROFIBUS communication
green, continuous light
data operation
red, flashing
error on the PROFIBUS, error can be resolved by a reset of the control
red, continuous light
error on the PROFIBUS, error cannot be resolved by a reset of the control
orange, continuous light
service operation active
2)
24
Note: The LED remains off until the BPS 34 is recognised by the PROFIBUS. Only after
the PROFIBUS has addressed the BPS 34 for the first time, the following status descriptions apply.
BPS 34
Leuze electronic
Leuze electronic
Connector units MS 34 … / MSD 1 101
5.2
Modular Service Display MSD 1 101
5.2.1
General information
The modular service display is used to display the calculated positions and operational data
on the one hand, and as simple access to the service interface on the other. The RS 232
service interface of the BPS 34 is located on the 9-pin sub-D connector of the MSD.
To connect the MSD 1 101 to the MS 34 105, an 8-pin cable (M 12) with a length of 2 m is
used (see chapter 10.3 "Accessory modular service display").
Using the service display, new settings for the BPS 34 can be tried quickly and easily,
without having to configure these settings via the PROFIBUS. The settings can be made via
PC using the BPS Configuration Tool.
Once optimal settings for standard operation have been found, these must be configured in
the PROFIBUS project in order for them to become permanently active.
Notice!
The BPS 34, in combination with the MS 34 10x, is equipped with an internal parameter
memory in which all configured settings are stored. When switching back from maintenance
mode to PROFIBUS mode, the settings specified in maintenance mode are overwritten by
the settings stored in the control.
TNT 35/7-24V
Attention!
If parameters are changed that can also be set via the PROFIBUS, they are overwritten with
the parameter setting defined in the PROFIBUS project after PROFIBUS start-up. If device
or module parameters are to be changed permanently, they must be set in the PROFIBUS
project.
Leuze electronic
BPS 34
25
Connector units MS 34 … / MSD 1 101
5.2.2
Leuze electronic
Dimensioned drawing
A LED indicator
B M12 device plug, 8-pin, for connecting to the MS 34 105
Figure 5.2:
5.2.3
Modular Service Display MSD 1 101
Electrical connection
MSD 1 101
The connection between the MSD 1 101 and the MS 34 105 is established via the preconfigured cable KB 034 2000. The service interface for connecting a PC is located inside
the MSD 1 101 and is designed as a 9-pin sub-D connector. The pin configuration of the 9pin sub-D connector corresponds to a standard RS 232 interface:
• PIN 2 = RxD
• PIN 3 = TxD
• PIN 5 = GND
26
BPS 34
Leuze electronic
Leuze electronic
6
Barcode tape
6.1
General information
Barcode tape
The barcode tape (BCT) is delivered on a roll. A roll contains up to 200 m of BCT, with the
wrapping direction from the outside to the inside (smallest number on the outside). If a BCT
is ordered which is considerably longer than 200 m, the total length is divided into rolls of
200 m each (see chapter 10.9 "Type overview: Barcode tape" on page 98).
Figure 6.1:
Roll with barcode tape
Leuze electronic
BPS 34
TNT 35/7-24V
Features:
• Robust and durable polyester adhesive tape
• High dimensional stability
• Max. length 10’000 m
• Self-adhesive, high adhesive strength
27
Leuze electronic
Barcode tape
6.2
Specifications of the barcode tape
Dimensions
Standard height
Length
Construction
Manufacturing process
Surface protection
Base material
Adhesive
Adhesive thickness
Adhesive strength
(average values)
Environmental data
Recom. processing temperature
Temperature resistance
Dimensional stability
Curing
Thermal expansion
Tearing resistance
Elongation at tear
Weathering resistance
Chemical resistance
(tested at 23 °C for 24 h)
Behaviour in fire
Mounting surface
Table 6.1:
28
47 mm (other heights on request)
0 … 5 m, 0 … 10 m, 0 … 20 m, …, 0 … 150 m, 0 … 200 m,
special lengths and special codings for lengths from
150 m, for details see order guide in chapter 10.9, page 98
Filmsetting
Polyester, matt
Polyester film, affixed without silicone
Acrylate adhesive
0.1 mm
on aluminium:
25 N/25 mm
on steel:
25 N/25 mm
on polycarbonate: 22 N/25 mm
on polypropylene: 20 N/25 mm
0 °C … +45 °C
-40 °C … +120 °C
no shrinkage, tested according to DIN 30646
final curing after 72 h, the position can be detected immediately by the BPS 34 after the BCT is affixed
due to the high elasticity of the BCT, thermal expansion of
the base material on which the BCT is affixed is not
known to have an effect
150 N
min. 80 %, tested in accordance with DIN 50014,
DIN 51220
UV-light, humidity,
salt spray (150 h/5 %)
transformer oil, diesel oil, white spirit, heptane,
ethylene glycol (1:1)
self-extinguishing after 15 s, does not drip
grease-free, dry, clean, smooth
Specifications of the barcode tape
BPS 34
Leuze electronic
Leuze electronic
6.3
Barcode tape
Mounting the barcode tape
To prevent deposits of dirt from forming, it is recommended that the BCT be affixed vertically, possibly with a roof-like cover. If the application does not permit this, permanent
cleaning of the BCT by on-board cleaning devices such as brushes or sponges is not
permitted in any case. Permanent on-board cleaning devices polish the BCT and give it a
glossy finish. The read quality deteriorates as a result.
Notice!
When mounting the BCT, it must be ensured that neither strong sources of extraneous light
nor reflections of the base on which the BCT is affixed occur in the area of the scanning
beam.
The recommended interruption points on the BCT are at the provided cut marks.
000028
000032
00
Cut mark
Cut mark on the barcode tape
Notice!
Cutting the BCT and affixing the tape so that a gap forms which is so large that a label can
no longer be reliably detected in the scanning beam results in double positions during the
position calculation of the BPS. The gap must not be greater than the distance from one cut
mark to the next (max. one label).
max. 40 mm
Gap
000020
000024
000028
000032
000036
Cut mark
Figure 6.3:
Leuze electronic
Gap in the cut barcode tape
BPS 34
29
TNT 35/7-24V
Figure 6.2:
Leuze electronic
Barcode tape
Procedure:
• Examine the mounting surface. It must be flat, without warping, free of grease and
dust, and dry.
• Define a reference edge (e.g. metal edge of the busbar)
• Remove the backing and affix the BCT along the reference edge tension free.
Secure the BCT to the mounting surface by pressing down with the palm of your
hand. When affixing, make certain that the BCT is free of folds and creases and that
no air pockets form.
• Never pull the BCT. Because this is a plastic tape, forceful pulling may stretch it. This
results in a distortion of the measurement units on the tape. While the BPS 34 can
still perform the position calculation, the accuracy in this case is no longer ensured. If
the values are taught using a teach-in process, distortions are irrelevant.
• Expansion joints with widths up to several millimetres can simply be covered with the
barcode tape. The tape must not be interrupted at this location.
• Protruding screw heads can simply be taped over. Cut out the bar code which covers
the screw head at the cut marks.
• If the application dictates the necessity of a gap, the tape is to be affixed over this gap
and the affected cut marks cut out. If the gap is small enough that the scanning beam
can detect the label to the left or to the right of the gap, measurement values are
delivered without interruption. If the scanning beam cannot completely scan any label,
the BPS 34 returns the value 0. As soon as the BPS 34 can again scan a complete
label, it calculates the next position value.
• The maximum gap between two barcode positions without affecting the measurement
value is 40 mm.
Notice!
If the barcode tape was damaged, e.g. by falling parts, a repair kit can be downloaded from
the Internet (www.leuze.de -> Under the heading Download ->
Logistics -> Optical barcode positioning -> Repair Kit for Barcode Tape).
Notice!
You can also view a video which illustrates how to affix the barcode tape on the Internet at
www.leuze.de -> Download -> Logistics -> Optical barcode positioning -> Videos ->
How to mount BPS 34/37.
Attention!
Barcode tapes with different value ranges may not directly follow one another. If the value
ranges are different, the gap between the two BCTs must be greater than the detection
range of the scanning beam or control barcodes must be used (for further information see
chapter 6.4 on page 32).
Notice!
When working with the BCT in cold warehouses, it should be ensured that the BCT be affixed before the warehouse is cooled. However, if it should be necessary to work with the
BCT at temperatures outside of the specified processing temperature, please make certain
that the bonding surface as well as the BCT are at the processing temperature.
30
BPS 34
Leuze electronic
Leuze electronic
Barcode tape
Notice!
When working with BCT in curves, the BCT should only be partially cut at the cut mark and
affixed along the curve like a fan; it must also be ensured that the BCT is affixed without tension (see figure 6.3).
007000
007004
0070
08
00
70
12
Partial cutting of the barcode tape in curves
TNT 35/7-24V
Figure 6.4:
Leuze electronic
BPS 34
31
Leuze electronic
Barcode tape
6.4
Control barcode
With the aid of control barcodes, which are simply affixed over the barcode tape at the
necessary locations, functions can be activated and deactivated in the BPS 34.
Notice!
The control of functions using control barcodes is a new feature of the BPS 34. The implementation of additional control options via control barcodes is in preparation.
Structure of the control barcode
The control barcodes utilise code type Code128 with character set B; the position barcodes,
on the other hand, utilise Code128 with character set C. Code 128 with character set B
enables the display of all letters and numbers in the ASCII character set.
System arrangement
Control barcode
The control barcode is decoded in the
scans which are marked with this symbol
Figure 6.5:
System arrangement of control barcodes
The control barcode is affixed either within one or between two barcode tapes in such a way
that one position barcode is replaced or two barcode tapes are seamlessly connected to one
another.
Attention!
It must be ensured that only one control barcode is located in the scanning beam at any one
time. Thus, the minimum distance between two control barcodes is determined by the distance between the BPS and barcode tape and the resulting length of the scanning beam.
32
BPS 34
Leuze electronic
Leuze electronic
Barcode tape
For error-free function, when using control barcodes it must absolutely be ensured that the
distance between the BPS and barcode tape is selected large enough. The scanning beam
of the BPS should cover three or more barcodes; this is ensured at a distance which lies in
the working range of the reading field curve.
The control barcodes are simply affixed over the existing tape. When affixing the control
barcodes, make certain to cover entire barcodes to ensure that a barcode spacing of 4 cm
is maintained.
Control barcode correctly affixed on the
barcode tape
Figure 6.6:
6.4.1
TNT 35/7-24V
Control barcode incorrectly affixed on
the barcode tape
Correct positioning of the control barcode
Controllable functions
Measurement value switching between 2 barcode tapes with different value
ranges
The "MVS" control barcode is used to switch between two barcode tapes. The end of one
tape and the start of the next can end and begin, respectively, with completely different position barcodes. If the centre of the BPS 34 reaches the transition point of the control barcode,
the device switches to the second tape, provided the next position label is in its scanning
beam. As a result, the output position can always be uniquely associated with one tape.
Leuze electronic
BPS 34
33
Leuze electronic
Barcode tape
Figure 6.7:
"MVS" control barcode for switching between tapes
Use of the "MVS" control barcode for switching between tapes is not dependent on direction.
This means that it functions for switching from tape 1 to tape 2 and vice versa.
BPS centre
+ hysteresis
± 5 mm
Centre of
control label
Scanning beam
MVS
SM1
08504
Positions values
Direction of movement
8500
1808
Measurements
Figure 6.8:
Switching position with the "MVS" control barcode
If the "MVS" label is passed over, the new tape value is always output relative to the centre
of the device or label (see figure 6.8). In this situation, the hysteresis of ±5 mm is irrelevant.
If, however, the device is stopped within the hysteresis on the "MVS" label and the direction
changed, the starting position values have an inaccuracy ±5 mm.
34
BPS 34
Leuze electronic
Leuze electronic
Barcode tape
Notice!
When affixing the BCT in a system in which the end of one BCT meets the start of another
BCT (position value X with position value 0), ensure that position labels 0 - 20 are not used.
This means that position label 24 must be the first label used on the continuing barcode tape.
Notice!
If only the "MVS" label is read within the scanning beam, the scanning beam must not be
interrupted during the read operation until the scanner can again read a complete position
label.
If only the "MVS" label is located in the scanning beam, the voltage on the BPS 34 must not
be switched off. Otherwise the BPS 34 will return a position value of zero when the voltage
is switched back on.
Moreover, the scanner must not be configured while in this position. Otherwise, a value of
zero is output as long as no position label is present in the scanning beam due to the fact
that the scanning beam is switched off during configuration.
6.5
Repair kit
In these 4 files you will find all code information for a tape with lengths of 0 … 500 m,
500 … 1000 m, 1000 … 1500 m and 1500 … 2000 m. 1 m of barcode tape is provided on
each A4 sheet. Each metre is divided into 5 lines of 20 cm, each with 5 code segments of
information covering lengths of 4 cm each.
Procedure when replacing the defective area:
1.
2.
3.
Determine the coding of the defective area.
Print out the area determined to be defective
Affix the printed area over the defective location
Leuze electronic
BPS 34
35
TNT 35/7-24V
Notice!
If the barcode tape was damaged, e.g. by falling parts, a repair kit can be downloaded from
the Internet (www.leuze.de -> Under the heading Download ->
Logistics -> Optical barcode positioning -> Repair Kit for Barcode Tape).
Leuze electronic
Barcode tape
Important note for printing:
1.
2.
3.
4.
Select only those pages that are actually required.
Change the printer settings so that the code is not distorted.
Suggestion for printer settings, see figure 6.9.
Verify the printing result by measuring the distance between two codes (see
figure 6.10).
Cut the code strips and concatenate them. It is important that the code content
always increases or decreases in blocks of 4 cm.
Figure 6.9:
Printer settings for BCT repair kit
40 mm
000020
000024
000028
000032
000036
Figure 6.10: Checking the print results of the BCT repair kit
36
BPS 34
Leuze electronic
Leuze electronic
7
Mounting
7.1
Mounting the BPS 34
Mounting
There are two different types of mounting arrangements for the BPS 34:
• Using 4 M4x6 screws on the rear of the device.
• Using the BT 56 mounting device on the fastening grooves.
Dovetail fastening grooves
Laser-beam beam
hole
15-pin sub-D connector on the underside of the unit
4 fastening threads M 4 on the
rear of the device
BPS 34 mounting options
BT 56 mounting device
The BT 56 mounting device is available for mounting the BPS 34 using the fastening
grooves. It is designed for rod installation (Ø 16 mm to 20 mm). For ordering instructions,
please refer to chapter 10.6 on page 94.
Leuze electronic
BPS 34
37
TNT 35/7-24V
Figure 7.1:
Leuze electronic
Mounting
Clamping jaws for
mounting on the BPS
Clamp profile for
mounting to round or
oval pipes
Ø 16 … 20 mm
All dimensions in mm
A Rod holder, turnable 360 °
B Rods Ø 16 … 20 mm
Figure 7.2:
38
BT 56 mounting device
BPS 34
Leuze electronic
Leuze electronic
Mounting
Mounting example BPS 34
BPS 34
Modular hood with integrated connectors
MS 34 103 or
MS 34 105
Modular Service Display
MSD 1 101
BT 56 mounting device
Mounting example BPS 34
Notice!
During mounting, the following angles of inclination must be taken into account in the vertical
axis:
10 ° for a tape height of 47 mm,
7 ° for a tape height of 30 mm and
5 ° for a tape height of 25 mm; the working range of the reading field curve must also be taken into account.
Attention!
For the position calculation, the scanning beam of the BPS 34 must be incident on the barcode tape without interruption. Ensure that the scanning beam is always incident on the barcode tape when the system is moving.
Leuze electronic
BPS 34
39
TNT 35/7-24V
Figure 7.3:
Leuze electronic
Mounting
7.2
Device arrangement
Selecting a mounting location
In order to select the right mounting location, several factors must be considered:
• The scanning range determined from the scanning curve must be adhered to at all
locations where a position determination is to be made
• The BPS should be mounted at an angle of 10° (depending on the tape height, see
notice page 39) in the vertical axis relative to the barcode tape to ensure continued
reliable positioning results even in the event of soiling of the barcode tape.
• On the BPS 34, the beam is not emitted perpendicular to the cover of the housing, but
with an angle of 10 ° towards the top. This angle is intended to prevent total reflection
on the barcode tape. This beam exit is already integrated in the device. As a result,
the BPS can be at the minimum read distance and mounted parallel to the barcode
tape.
Centre of the scanning beam
(device centre, output position value)
Barcode tape
X
Scanning beam
000204
000208
0002122
000216
Beam exit
10˚
10 ° pitch
in the vertical
axis
(dependent on
the tape height,
see notice)
103 ± 2
0002000
10˚
Read distance
All dimensions in mm
Figure 7.4:
Beam exit and device arrangement of the BPS 34
Dimension X in figure 7.4 shows the mounting height of the BCT centre relative to the
housing of the BPS 34. Dimension X is dependent on the read distance. Please refer to the
following table for the value:
Read distance [mm]
40
Dimension X
Dimension X
Dimension X
Read distance [mm]
Read distance [mm]
[mm]
[mm]
[mm]
90
16
120
21
150
26
100
18
130
23
160
28
110
19
140
25
170
30
BPS 34
Leuze electronic
Leuze electronic
Mounting
Notice!
The best functionality is obtained when:
• the BPS is guided parallel to the tape.
• the permitted working range is not exited.
Mounting location
! When selecting a mounting location, pay attention to
• maintaining the required environmental conditions (humidity, temperature),
• possible soiling of the reading window due to liquids, abrasion by boxes, or packaging
material residues.
Mounting outdoors/devices with integrated heating
When mounting outdoors or for devices with integrated heating, also observe the following
points:
• mount the BPS 34 in a way which provides maximum thermal isolation, e.g. using
rubber-bonded metal.
• mount in such a way that the device is protected from relative wind; mount additional
shields if necessary.
Notice!
When installing the BPS 34 in a protective housing, it must be ensured that the scanning
beam can exit the protective housing without obstruction.
Mounting the barcode tape
The BPS 34 and barcode tape combination is mounted in such a way that the scanning
beam is unobstructed and is incident on the barcode tape as described in figure 7.4 on
page 40.
Notice!
For further information on mounting the barcode tape, please refer to chapter 6.3 on
page 29.
Leuze electronic
BPS 34
41
TNT 35/7-24V
7.3
Leuze electronic
Device parameters and interfaces
8
Device parameters and interfaces
8.1
PROFIBUS
8.1.1
General information
The BPS 34 with MS 34 103/MS 34 105 is designed as a PROFIBUS device (PROFIBUS
DP-V0 acc. to IEC 61784-1) with a baud rate of 12 MBd. The functionality of the device is
defined via parameter sets which are clustered in modules. These modules are contained in
a GSE file. The GSE file can be downloaded from the Leuze Homepage at www.leuze.de
-> under the heading Download -> Logistics -> Optical barcode positioning. By using
a user-specific project tool, such as, e.g., Simatic Manager for the Siemens programmable
logic control, the required modules are integrated into a project during commissioning and
its settings and parameters are adjusted accordingly. These modules are provided by the
GSE file.
All input and output modules described in this documentation are described from the
controller's perspective:
• Input data arrives at the controller
• Output data are sent out by the controller.
8.1.2
Electrical connection
Socket
(A-coded)
Socket
(A-coded)
MSD
SW IN/OUT
VIN
2
/INT
/SERV 1
DP OUT
GND
7
A (N)
2
3 GND
VCC 1
4
PE
B (P)
Socket
(B-coded)
SWOUT
2
TXD
3
4
6
SDA
5
RXD
SCL
3 GND
VOUT 1
4
SWIN
DP IN
A (N)
2
GND 3
1 VCC
4
B (P)
PE
Plug
(B-coded)
PE
PWR IN
SWOUT
2
GND 3
PE
1 VIN
4
SWIN
Plug
(A-coded)
Figure 8.1:Electrical connection of PROFIBUS connections DP IN and DP OUT
42
BPS 34
Leuze electronic
Leuze electronic
Device parameters and interfaces
DP IN - PROFIBUS DP incoming
DP IN (5-pin plug, B-coded)
Pin
DP IN
A (N)
2
GND 3
PE
1 VCC
4
B (P)
M 12 plug
(B-coded)
Figure 8.2:
Name
Remark
1
VCC
5 V DC for bus termination
2
A (N)
Receive/transmit data A-line (N)
3
GND
Functional earth for bus termination
4
B (P)
Receive/transmit data B-line (P)
5
PE
Functional earth
Thread
PE
Functional earth (housing)
Pin assignment DP IN
DP OUT - PROFIBUS DP outgoing
DPOUT (5-pin socket, B-coded)
A (N)
2
VCC 1
3 GND
4
PE
B (P)
M 12 socket
(B-coded)
Figure 8.3:
Pin
Name
1
VCC
5 V DC for bus termination
Remark
2
A (N)
Receive/transmit data A-line (N)
3
GND
Functional earth for bus termination
4
B (P)
Receive/transmit data B-line (P)
5
PE
Functional earth
Thread
PE
Functional earth (housing)
Pin assignment DP IN
Attention!
Protection class IP 65 is achieved only if the connectors and caps are screwed into place!
Leuze electronic
BPS 34
43
TNT 35/7-24V
DP OUT
Leuze electronic
Device parameters and interfaces
Notice!
For connecting DP IN and DP OUT, we recommend our ready-made PROFIBUS cables.
For further information, see chapter 10.8 on page 96.
The BPS 34 can be used in combination with an MS 34 103/MS 34 105 to branch out the
PROFIBUS network. The continuing network is connected via DP OUT.
If the PROFIBUS is not connected to another subscriber via the MS 34 10x, the DP OUT
connection must be fitted with a TS 02-4-SA terminator plug for the purpose of bus termination. For further information, see also chapter 10.4 on page 94.
Attention!
Never open the device yourself, as this may compromise protection class IP 65.
Before connecting the device, be sure that the supply voltage agrees with the value printed
on the name plate.
Connection of the device and cleaning must only be carried out by a qualified electrician.
The power supply unit for the generation of the supply voltage for the BPS 34 and the respective connection units must have a secure electrical insulation through double insulation
and safety transformers according to EN 60742 (corresponds to IEC 60742).
Be sure that the earthing conductor is connected correctly. Error-free operation is only guaranteed if the device is properly earthed.
If faults cannot be corrected, the device should be removed from operation and protected
against possible use.
To then further isolate the error, proceed as described in chapter 9 on page 92.
44
BPS 34
Leuze electronic
Leuze electronic
8.1.3
Device parameters and interfaces
PROFIBUS address
In the modular hoods with integrated connectors MS 34 103 and MS 34 105, the
PROFIBUS address can be set via two rotary switches and one slide switch.
The configuration and function of the address switches is shown in figure 8.4.
Slide switch for the hundreds (marked with 102)
Rotary switch for the tens (marked with 101)
Rotary switch for the single digits (marked with 100)
Position of the slide
switch:
Top
address
100 - 126
Bottom
address
1 - 99
Connector to the BPS 34
Figure 8.4:Setting the PROFIBUS address in the MS 34 103/MS 34 105
8.1.4
General information on the GSE file
This file stores all the data required for the operation of the BPS 34. This data consists of
device parameters required for operation of the BPS 34 and the definition of the control and
status bits. If parameters are changed in the project tool, for example, these changes are
stored in the project, not in the GSE file.
The GSE file is part of the device and must not be changed manually. The file is not changed
by the system either.
If the BPS 34 is operated in a PROFIBUS network, configuration must be performed exclusively via the PROFIBUS. The functionality of the BPS 34 is defined via GSE parameter
sets. The parameters and their functions are structured in the GSE file using module. A userspecific configuration tool is used during PLC program creation to integrate the required
modules and configure them appropriately for their respective use.
During operation of the BPS 34 on the PROFIBUS, all parameters are set to default values.
If these parameters are not changed by the user, the device functions with the default
settings delivered by Leuze electronic. For the default settings of the BPS 34, please refer
to the following module descriptions.
Notice!
A least one module in the GSE file must be activated in the configuration tool for the control,
usually the "Position value" module 1.
Leuze electronic
BPS 34
45
TNT 35/7-24V
You can find the GSE file at www.leuze.de -> Download -> Logistics -> Optical barcode
positioning.
Leuze electronic
Device parameters and interfaces
Notice!
Some controls make available a so-called "universal module". This module must not be activated for the laser.
Attention!
The BPS 34 does not permanently store parameters changed via the PROFIBUS. Following
Power off/on, the currently configured parameters are downloaded from the PROFIBUS
manager. If no PROFIBUS manager is available following Power OFF/ON, the BPS 34 activates its stored default settings.
8.1.5
Structure of the GSE modules
In the current version, a total of 27 modules are available for use. The modules may be
included into the project according to requirements and application.
The modules fall into the following categories:
• Parameter module for the configuration of the BPS 34.
• Status or control modules that influence the input/output data.
• Modules that may include both parameters and control or status information.
Notice!
All input and output modules described in this documentation are described from the
controller's perspective.
Described inputs (I) are inputs in the control.
Described outputs (O) are outputs in the control.
Described parameters (P) are parameters of the GSE file in the control.
Notice!
At least one module must be activated to permit operation of the device at the PROFIBUS
DP.
Notice!
Under some circumstances, not all 27 modules can be activated simultaneously in the configuration tool. Otherwise, the available memory for a subscriber may be exceeded. The
maximum available memory for a device is control dependent.
46
BPS 34
Leuze electronic
Leuze electronic
8.1.6
Device parameters and interfaces
Overview of the GSE modules
Notice!
Inputs and outputs are described from the perspective of the PROFIBUS master.
Module name
Module contents
(P) = Parameter, (O) = Output, (I) = Input
Page
M1
page 51
M2
page 52
M3
page 53
M4
page 55
M5
page 56
M6
page 57
M7
page 59
M8
page 61
M9
page 63
M10
page 65
M11
page 66
Leuze electronic
Position value
Resolution
Static preset
Dynamic preset
Offset value
Scaling
Switching input
Switching output
Control
Measurement value
acquisition
Measurement value
preparation
(P) Sign
(I) Position value
(P) Resolution for the position value
(P) Preset value added to tape value
(O) Preset teach
(O) Preset reset
(O) Preset teach
(O) Preset reset
(O) Preset value
(P) Offset value
(P) Scaling factor
(P) Inversion
(P) Mode
(P) Debounce time
(P) Start-up delay
(P) Pulse duration
(P) Switch-off delay
(P) Function
(I) State
(P) DC bias level
(P) Selection of the velocity limit value
(P) Pulse duration
(P) Switch-on function
(P) Switch-off function
(O) Switching output "PROFIBUS edge"
(P) Measurement start mode
(P) Measurement stop mode
(P) Stop timeout
(I) Status of position controller
(O) Start event
(O) Stop event
(O) BPS standby
(P) Maximum permitted measurement length
(P) Minimum permitted measurement length
(P) Integration depth
(O) Count direction for position calculation
BPS 34
TNT 35/7-24V
Module
47
Leuze electronic
Device parameters and interfaces
Module
Module name
Module contents
(P) = Parameter, (O) = Output, (I) = Input
Page
M12
page 68
M13
page 69
M14
page 71
M15
page 72
M16
page 73
M17
page 74
M18
page 75
M19
page 76
M20
page 77
M21
page 78
48
(I) Measurement error
(I) Range status (outside of measurement range)
(I) Preset active
(I) Dynamic preset teach
Status
(I) State
(I) Position limit value status 1
(I) Position limit value status 2
(I) Standby status
(P) Min/Max mode
(P) Min/Max duration
Min/Max position
(I) Min position
(I) Max position
(O) Min/Max reset
(P) Limit value checking on/off
(P) Switching mode (value is above or below the
Static position limit
defined limits)
value 1
(P) Hysteresis
(P) Limit value
(P) Limit value checking on/off
(P) Switching mode (value is above or below the
Static position limit
defined limits)
value 2
(P) Hysteresis
(P) Limit value
(P) Limit value checking on/off
(P) Switching mode (value is above or below the
Dynamic position limit
defined limits)
value 1
(P) Hysteresis
(O) Limit value
(P) Limit value checking on/off
(P) Switching mode (value is above or below the
Dynamic position limit
defined limits)
value 2
(P) Hysteresis
(O) Limit value
Measuring error toler- (P) Position tolerance time
ance
(P) Error output delay
(I) Status
Service
(O) Reset to factory settings
Velocity
Velocity parameters
(I) Current velocity
(P) Resolution
(P) Scaling factor
(P) Integration depth
(P) Tolerance time (on error message)
(P) Error output delay
BPS 34
Leuze electronic
Leuze electronic
Module name
Module contents
(P) = Parameter, (O) = Output, (I) = Input
Page
M22
page 80
M23
page 82
M24
page 84
M25
page 85
M26
page 88
M27
page 90
Table 8.1:
Leuze electronic
(P) Start mode of velocity measurement
(P) Velocity measurement stop mode
Control
(I) Velocity measurement status
velocity
(O) Start event
measurement
(O) Stop event
(O) Min/Max velocity mode
(O) Min/Max velocity reset
(I) Measurement error
(I) Limit value status 1 exceeded
(I) Limit value status 2 exceeded
(I) Limit value status 3 exceeded
(I) Limit value status 4 exceeded
Status
(I) Dynamic limit value status exceeded
velocity
(I) Movement status
measurement
(I) Direction of movement
(I) Compare limit value status 1
(I) Compare limit value status 2
(I) Compare limit value status 3
(I) Compare limit value status 4
(I) Compare dynamic limit value status
Min/Max
(I) Minimum velocity
velocity
(I) Maximum velocity
(P) Velocity limit value mode (active/not active)
(P) Direction selection (both directions or only one)
(P) Switching mode (value is above or below the
Static velocity limit
defined limits)
values
(P) Velocity limit value
(for limit value 1 … 4)
(P) Hysteresis
(P) Range start
(P) Range end
(O) Limit value control
(O) Switching mode (value is above or below the
defined limits)
Dynamic
(O) Direction selection
velocity
(O) Limit value
limit values
(O) Hysteresis
(O) Range start
(O) Range end
(P) Actual length
Tape value correction (P) Range start
(P) Range end
TNT 35/7-24V
Module
Device parameters and interfaces
Overview of the GSE modules
BPS 34
49
Leuze electronic
Device parameters and interfaces
8.1.7
Detailed description of the modules
Notice!
In the following detailed descriptions of the modules, you will find in the last column of the
tables cross references (CR) to parameters and input/output data of other modules
which are directly related to the described parameter. These cross references must be observed during configuration.
The individual modules are numerically labelled from 1 … 27.
The parameters and input/output data within a module are alphanumerically labelled
from a … z .
Example:
The a Static preset value in [mm] parameter in module 3 becomes active only when the
preset teach occurs via module 12 c , 7 g or 3 b .
50
BPS 34
Leuze electronic
Leuze electronic
Device parameters and interfaces
8.1.7.1 Module 1: Position value
Description:
With this module, the current position value is output.
Notice!
The position value is the position value calculated from the tape value and the settings for
resolution, preset and offset.
Parameter
Parameter
Sign
a
Description
Output mode for sign.
Rel.
addr.
0
Data
Value range
type
unsign 0: Two's complement
8
1: Sign + magnitude
Default
Unit
CR to
module
0
–
–
Parameter length: 1 byte
Hex coding of module 1 "Position value"
Sign
13
00
Input data
Input data
b
Position
value
Description
Output of the current position.
Rel.
addr.
Data
type
Value range
Default
Unit
CR to
module
0
sign
32
-10’000’000 … +10’000’000
(for a resolution in mm)
0
scaled
–
Input data length: 4 byte
Notice!
A negative number is represented in the input data by a 1 in the most significant bit.
Output data
none
Leuze electronic
BPS 34
51
TNT 35/7-24V
Internal address
of module 1
The value listed in the table shows the hex coding of the default settings.
Leuze electronic
Device parameters and interfaces
8.1.7.2 Module 2: Resolution
Description
With this module, the resolution for the position value of module 1 is defined. The BPS 34
also performs a rounding correction (The position value is divided by the defined value
range).
Notice!
The resolution only determines the mathematical decimal value and has no effect on the
measurement accuracy.
Parameter
Parameter
Description
The parameter specifies the
resolution for the position value.
The resolution has no effect on
Resolution
- Static preset
in [mm]
- Dynamic preset
- Offset
Rel.
addr.
a
0
Data
type
1: 0.01
2: 0.1
unsign 3: 1
8
4: 10
5: 100
6: 1’000
Value range
Default
Unit
CR to
module
3
mm
–
Parameter length: 1 byte
Hex coding of module 2 "Resolution"
Internal address
of module 2
Resolution
The value listed in the table shows the hex coding of the default settings.
0A
03
Input data
none
Output data
none
52
BPS 34
Leuze electronic
Leuze electronic
Device parameters and interfaces
8.1.7.3 Module 3: Static preset
Notice!
Underlined in the CR column are the modules which must be activated in addition to the current module.
Description
With this module, a preset value can be defined which the BPS 34 outputs following a teach
event. Defined as a teach event is either bit 0.0 in the output data of this module or a
switching input function. After reading in the teach event, the current position value is
replaced by the preset value and the position value now calculated and output on the basis
of the preset value. The preset remains stored in the BPS 34 and remains active even
following a new start. In order for the BPS 34 to again output the position value without the
preset, bit 0.1 in the output data must be set.
Notice!
In the event of a device change, the preset value is retained in the MS 34 10x. The activation
of the preset value (preset teach) at the intended position is not necessary.
Parameter
Parameter
Description
Rel.
addr.
a
Static pre- New position value after teach
set value in event
[mm]
0
Data
type
Value range
unsign
0 … 10’000’000
32
Default
Unit
0
mm
CR to
module
12c
7g
or
3b
Notice!
The preset value is always entered in units of mm, independent of the resolution setting
(module 2). The scaling factor (module 6) has no effect on the static preset value.
Hex coding of module 3 "Static preset"
Internal address
of module 3
Static preset
The value listed in the table shows the hex coding of the default settings.
06
00 00 00 00
Leuze electronic
BPS 34
53
TNT 35/7-24V
Parameter length: 4 byte
Leuze electronic
Device parameters and interfaces
Input data
none
Output data
Output
data
b
Preset
teach
c
Preset
reset
Description
Rel.
addr.
Data
type
Read in the preset value
0.0
Bit
Preset value is deactivated.
0.1
Bit
Value range
Default
Unit
CR to
module
0->1 = Teach
0
–
–
0->1 = Reset
0
–
–
Output data length: 1 byte
54
BPS 34
Leuze electronic
Leuze electronic
Device parameters and interfaces
8.1.7.4 Module 4: Dynamic preset
Notice!
Underlined in the CR column are the modules which must be activated in addition to the current module.
Description
With this module, a preset value can be defined which the BPS 34 outputs following a teach
event. Defined as a teach event is either bit 0.0 in the output data of this module or a
switching input function. After reading in the preset, the current position value is replaced by
the preset value and the position now calculated and output on the basis of the preset. The
preset remains stored in the BPS 34 and remains active even following a new start. In order
for the BPS 34 to again output the tape value, bit 0.1 in the output data must be set (preset
reset). The preset value is transmitted to the BPS 34 together with the output data of the
PROFIBUS master. Thus, it can be changed during operation (dynamically).
Parameter
none
Input data
none
Output
data
a
Preset
teach
b
Preset
reset
c
Preset
value
Description
Rel.
addr.
Data
type
Read in the preset value
0.0
Bit
Reset to default,
deactivate preset value
0.1
Bit
New position value after preset
teach
1
Value range
Default
Unit
0->1 = Teach
0
–
0->1 = Reset
0
–
0
mm
unsign
0 … 10’000’000
32
CR to
module
12c
12d
7g
or
4a
Output data length: 5 byte
Notice!
The preset value is always entered in units of mm, independent of the resolution setting
(module 2). The scaling factor (module 6) has no effect on the dynamic preset value.
Leuze electronic
BPS 34
55
TNT 35/7-24V
Output data
Leuze electronic
Device parameters and interfaces
8.1.7.5 Module 5: Offset value
Notice!
Underlined in the CR column are the modules which must be activated in addition to the current module.
Description
This module adds an offset value to the tape value.
Parameter
Parameter
Description
Rel.
addr.
Offset value added to tape value
0
Data
type
Value range
Default
Unit
CR to
module
0
mm
1
a
Offset
value in
[mm]
sign32 -10’000’000 … 10’000’000
Parameter length: 4 byte
Notice!
If module 3 "Static preset" or module 4 "Dynamic preset" is activated and, as a result, a new
value assigned to the tape value, the offset function no longer affects the position value. The
offset is not reactivated until the preset function (static and dynamic) is cancelled. The offset
value is entered in mm. When entering the offset value, the scaling in module 6 must be taken into account.
Hex coding of module 5 "Offset value"
Internal address
of module 5
Offset value
The value listed in the table shows the hex coding of the default settings.
09
00 00 00 00
Input data
none
Output data
none
56
BPS 34
Leuze electronic
Leuze electronic
Device parameters and interfaces
8.1.7.6 Module 6: Scaling
Notice!
Underlined in the CR column are the modules which must be activated in addition to the current module.
Description
The scaling function is used to convert the tape values to any unit of measurement. To do
this, the tape value is multiplied by the scaling factor.
Parameter
Parameter
a
Scaling
factor in
[‰]
Description
Scaling factor used to convert
the position values
Rel.
addr.
0
Data
type
Value range
unsign
0 … 65’535
16
Default
Unit
1’000
Per
thousand
CR to
module
1
Parameter length: 2 byte
Affected by this module are:
• Offset value (module 5)
• Static position limit values 1 and 2 (modules 14 and 15)
• Hysteresis of static position limit values 1 and 2 (modules 14 and 15)
• Dynamic position limit values 1 and 2 (modules 16 and 17)
• Hysteresis of dynamic position limit values 1 and 2 (modules 16 and 17)
The static preset or dynamic preset modules (module 3 or module 4) are not affected by the
scaling.
Leuze electronic
BPS 34
57
TNT 35/7-24V
Notice!
When entering offset values in module 5, it must be ensured that the scaling factor is taken
into account.
Leuze electronic
Device parameters and interfaces
Hex coding of module 6 "Scaling"
Internal address
of module 6
Scaling factor
The value listed in the table shows the hex coding of the default settings.
08
03 E8
Input data
none
Output data
none
58
BPS 34
Leuze electronic
Leuze electronic
Device parameters and interfaces
8.1.7.7 Module 7: Switching input
Notice!
Underlined in the CR column are the modules which must be activated in addition to the current module.
Description
The module defines the mode of operation of the digital switching input.
Parameter
Parameter
Description
a
The parameter defines the logic
of the pending signal. In case of
an inversion, an external HIGH
level is interpreted as an internal
LOW level.
This parameter controls the
release of the switching input.
This parameter defines a
debounce time which is implemented in software.
b
Mode
c
Debounce
time in
[ms]
d
Value range
Default
Unit
CR to
module
0
unsign 0: No (active high)
8
1: Yes (active low)
0
–
–
1
unsign 0: Off
8
1: On
1
–
–
2
unsign
0 … 255
8
5
ms
–
3
unsign
0 … 65’535
16
0
ms
–
5
unsign
0 … 65’535
16
0
ms
–
The parameter influences the
timing during switch-on
Start-up
delay in
[ms]
e
Data
type
TNT 35/7-24V
Inversion
Rel.
addr.
The parameter defines the minimum pulse duration of the input
signal.
Pulse duration in [ms]
Leuze electronic
BPS 34
59
Leuze electronic
Device parameters and interfaces
The parameter defines a time
delay for the signal during switchoff.
f
Switch-off
delay in
[ms]
7
unsign
0 … 65’535
16
g
0
ms
0: No function
–
3a
or
4c
13e
4: Teach preset
The parameter specifies the
function which is to be activated
or deactivated by a change of
state at the switching input.
Function
9
–
5: Reset min/max position
7: Start position measureunsign ment
9: Stop position measurement
8
10: Teach limit value 1
11: Teach limit value 2
9a
7
–
9b
14a 16a
15a 17a
22b
24
22a
22b
Default
Unit
CR to
module
0
–
–
12: Reset min/max velocity
13: Start velocity measurement
14: Stop velocity measurement
Parameter length: 10 bytes
Hex coding of module 7 "Switching input"
Internal address
of module 7
Inversion
address 0
Mode
address 1
Debounce time
address 2
Start-up delay
address 3
Pulse duration
address 5
Switch-off delay
address 7
Function
address 9
The value listed in the table shows the hex coding of the default settings.
01
00
01
05
00 00
00 00
00 00
04
Input data
Input data
Description
h
State of the signal of the switching input
State
Rel.
addr.
Data
type
0.0
Bit
Value range
0: Input not active
1: Input active
Input data length: 1 byte
Output data
none
60
BPS 34
Leuze electronic
Leuze electronic
Device parameters and interfaces
8.1.7.8 Module 8: Switching output
Notice!
Underlined in the CR column are the modules which must be activated in addition to the current module.
Description
The module defines the mode of operation of the digital switching output.
Parameter
Description
a
The parameter defines the DC bias
level of the switching output.
b
Defines whether the switching output is controlled by
DC bias
level
Velocity
limit value
selection
static velocity limit value 1,
static velocity limit value 2,
static velocity limit value 3,
static velocity limit value 4
or the
dynamic velocity limit value
The parameter defines the switch-on
c
Pulse dura- time period for the switching output. If
tion in [ms] the value is 0, the signal is static.
d
Switch-on
function
[ON]
The parameter defines the events
which set the switching output:
- velocity valid
- velocity not valid
- position limit value 1 reached
- position limit value 1 not reached
- outside measurement range
- inside measurement range
- position limit value 2 reached
- position limit value 2 not reached
- erroneous measurement
- successful measurement
- PROFIBUS positive edge
- PROFIBUS negative edge
- velocity limit value reached
- velocity limit value not reached
Leuze electronic
Rel.
addr.
Data
type
Value range
unsign 0: LOW (0 V)
8
1: HIGH (+UB)
0
1.0
1.1
1.2
1.3
Bits
for each
0: No
1: Yes
1.4
4.0
4.1
4.2
4.3
4.4
4.5
4.6
4.7
5.2
5.3
5.4
5.5
5.6
5.7
Unit
CR to
module
0
–
–
0
0
0
0
25 for
static
–
26 for
dynamic
0
unsign
0 … 1’300
16
2
Default
Bits
BPS 34
for each
0: Not active
1: Active
400
0
0
0
0
0
0
0
0
1
0
0
0
0
0
ms
–
–
22
22
14 + 16
14 + 16
10
10
15 + 17
15 + 17
1+9
1+9
8
8
25
25
61
TNT 35/7-24V
Parameter
Leuze electronic
Device parameters and interfaces
e
Switch-off
function
[OFF]
The parameter specifies the events
which reset the switching output:
- velocity valid
- velocity not valid
- position limit value 1 reached
- position limit value 1 not reached
- outside measurement range
- inside measurement range
- position limit value 2 reached
- position limit value 2 not reached
- erroneous measurement
- successful measurement
- PROFIBUS positive edge
- PROFIBUS negative edge
- velocity limit value reached
- velocity limit value not reached
6.0
6.1
6.2
6.3
6.4
6.5
6.6
6.7
7.2
7.3
7.4
7.5
7.6
7.7
Bits
for each
0: Not active
1: Active
0
0
0
0
0
0
0
0
0
1
0
0
0
0
–
22
22
14 + 16
14 + 16
10
10
15 + 17
15 + 17
1+9
1+9
8
8
25
25
Parameter length: 8 byte
Notice!
The events of the switch-on function and switch-off function are both linked to one another
with a logical OR.
Hex coding of module 8 "Switching output"
Internal address
of module 8
DC bias level
address 0
Velocity limit value
selection
address 1
Pulse duration
address 2
Switch-on function
address 4
Switch-off function
address 6
The value listed in the table shows the hex coding of the default settings.
02
00
00
01 90
04 00
08 00
Input data
none
Output data
Output data
Description
This bit can be used to operate
f
the switching output if the
Switching output
"PROFIBUS edge" function is
PROFIBUS edge
configured.
Rel.
addr.
Data
type
0.0
Bit
Value range
Default
Unit
CR to
module
0 -> 1: Positive edge
1 -> 0: Negative edge
0
–
–
Output data length: 1 byte
Notice!
With the "PROFIBUS edge" function, the switching output can be directly activated or deactivated by setting bit 0.0.
62
BPS 34
Leuze electronic
Leuze electronic
Device parameters and interfaces
8.1.7.9 Module 9: Controller
Description
The Control module manages timing of the position calculation by starting and stopping the
decoding. Control is performed depending on certain events such as the switching input,
time functions or PROFIBUS output bits. Using parameters, the events which influence the
states are determined.
Parameter
a
Measurement start
mode
Description
Rel.
addr.
The start mode determines by
which event the position measurement is started.
0
The measurement stop mode
determines after which event
the position measurement is
stopped.
1
Time for stop timeout
2
b
Measurement stop
mode
c
Stop timeout in [ms]
Data
type
Value range
0: Deactivated
1: After initialisation
unsign
2: By event:
8
Switching input or start event
by setting output bit 0.0
0: No function
1: After valid measurement
result
2: After timeout (stop timeout)
3: After timeout with retrigger
(stop timeout) by setting outunsign
put bit 0.0 or by the switching
8
input
4: By stop event or by setting output bit 0.1 or by the
switching input (the switching
input must be programmed
for this purpose)
5: By an error
unsign
0 … 65’535
16
Default
Unit
CR to
module
1
–
7g
4
–
7g
10’000
ms
–
TNT 35/7-24V
Parameter
Parameter length: 4 byte
Hex coding of module 9 "Control"
Internal address of module 9
Measurement start mode
address 0
Measurement stop mode
address 1
Stop timeout
address 2
The value listed in the table shows the hex coding of the default settings.
03
01
04
27 10
Leuze electronic
BPS 34
63
Leuze electronic
Device parameters and interfaces
Input data
Input data
d
Description
Signals the current state of the
internal position control of the
BPS 34
Status of
position
controller
Rel.
addr.
0
Data
type
Value range
0: Init
unsign 1: Idle
8
2: Measure
4: Standby
Default
Unit
CR to
module
0
–
–
Input data length: 1 byte
Notice!
These input data signal the state of the BPS 34:
•
•
•
•
Init: Base setting during initial startup of the BPS 34
Idle: The BPS 34 is in idle state (scanning beam is off, but motor is running)
Measure: The BPS 34 is in measurement state (data are output in module 1)
Standby: The BPS 34 is in waiting state (laser off and motor off).
Output data
Output
data
Description
e
Start
event
f
Stop event
g
BPS
standby
Rel.
addr.
Data
type
Event starts position measurement
0.0
Bit
Event stops position measurement
0.1
Switches the BPS 34 to standby
operation
0.7
Value range
Default
Unit
CR to
module
0 -> 1: Start
0
–
7g
Bit
0 -> 1: Stop
0
–
–
Bit
0: BPS active
1: BPS in standby
0
–
–
Output data length: 1 byte
Notice!
The standby function can only be activated while in "Measure" state. This function switches
off the motor and laser. It takes approx. 2 sec. to switch the BPS 34 back on (valid measurement values at the interface)
In "Idle" state, the motor continues to run. Only the laser is switched off. It takes approx.
1 sec. to switch the BPS 34 back on (valid measurement values at the interface)
If the start-stop event is to occur at the switching input, the "function" parameter must be
configured with the "start/stop measurement" parameter in module 7 "Switching input".
64
BPS 34
Leuze electronic
Leuze electronic
Device parameters and interfaces
8.1.7.10 Module 10: Measurement value acquisition
Description
With this module, a working range on the barcode tape can be defined. The BPS 34 outputs
position values within these minimum and maximum limits. Outside of these limits, a position
value of zero is output.
Parameter
Parameter
Description
Rel.
addr.
a
Maximum permitted measMax.
measurement urement length
length in [mm]
Value range
Default
Unit
CR to
module
0
unsign
0 … 2’147’483’647
32
10’000’000
mm
8d
4
unsign
0 … 2’147’483’647
32
0
mm
8d
b
Minimum permitted measMin.
measurement urement length
length in [mm]
Data
type
Parameter length: 8 byte
Notice!
The signal output can be used to indicate that the measured value is outside of the measurement range. To enable this function, the "outside measurement range" or "inside measurement range" parameter must be activated in module 8.
Hex coding of module 10 "Measurement value acquisition"
Max. measurement length
address 0
Min. measurement length
address 4
04
00 98 96 80
00 00 00 00
TNT 35/7-24V
Internal address
of module 10
The value listed in the table shows the hex coding of the default settings.
Input data
none
Output data
none
Leuze electronic
BPS 34
65
Leuze electronic
Device parameters and interfaces
8.1.7.11 Module 11: Measurement value processing
Description
The integration depth parameter is used to specify the number of raw position data which is
used for integration in order to determine the position value.
In order to obtain positive or negative position values depending on the direction of movement of the BPS 34, the count direction can be selected as normal or inverted in the output
data of this module.
In order to obtain more exact measurement data while in the static state or for very slow
travel speeds, the integration depth can be increased here. If, however, a high integration
depth is used for high speeds, the contouring error is increased. With respect to contouring
error and exact measurement data, very good results have been obtained using
8 integration steps. Using 8 integration steps, the integration time is 16 ms. Thus, the
BPS 34 delivers a new position value to the interface every 2 ms which is 8 ms old.
Parameter
Parameter
Description
Number of consecutive scans
a
Integration which are to be used for position
determination.
depth
Rel.
addr.
0
Data
type
Value range
unsign
4 … 15
8
Default
Unit
8
Measurements
CR to
module
8d
Parameter length: 2 byte
Integration depth
66
Integration time [ms]
4
8
5
10
6
12
7
14
8 (default)
16
9
18
10
20
11
22
12
24
13
26
14
28
15
30
BPS 34
Leuze electronic
Leuze electronic
Device parameters and interfaces
Hex coding of module 11 "Measurement value preparation"
Internal address
of module 11
Integration depth
address 0
The value listed in the table shows the hex coding of the default settings.
05
00 08
Input data
none
Output data
Output
data
b
Count
direction
Description
Count direction for position calculation
Rel.
addr.
Data
type
0.0
Bit
Value range
0: Normal
: Inverted
Default
Unit
CR to
module
0
–
–
Output data length: 1 byte
The position value is output with "normal" count direction. With the "inverted" count direction,
10’000’000 mm minus the position value is output. This behaviour can be influenced using
the "Static preset"/"Dynamic preset" modules (module 3 and module 4, respectively) and
the "Offset" module (module 5).
Count direction "normal"
Position value = tape value
1’400’000 mm
0 mm
10’000’000 mm
Count direction
Count direction "inverted"
Position value
8’600’000 mm (=10’000’000 mm - tape value)
0 mm
10’000’000 mm
Count direction
Figure 8.12: Count direction for position calculation
Leuze electronic
BPS 34
67
TNT 35/7-24V
Notice!
The BPS 34 is set as follows by default:
Leuze electronic
Device parameters and interfaces
8.1.7.13 Module 12: Status
Notice!
Underlined in the CR column are the modules which must be activated in addition to the current module.
Description
This module supplies various BPS 34 status information to the PROFIBUS master.
Parameter
none
Input data
Input data
Description
Default
Unit
CR to
module
0: OK
1: Error
0
–
–
Bit
0: OK, within measurement
range
1: Measurement range
exceeded
0
–
10
0.2
Bit
0: No preset active
1: Preset active
0
–
3a
4c
0.3
Bit
0,1: Dyn. preset teach
0
–
3a
4c
Indicates that limit value 1 has
been exceeded (measurement
value monitoring module).
0.4
Bit
0: No limit value violation
1: Value greater than limit
0
–
14d
16d
Indicates that limit value 2 has
been exceeded (measurement
value monitoring module).
0.5
Bit
0: No limit value violation
1: Value greater than limit
0
–
15d
17d
Signals the standby status
(Control module)
0.7
Bit
0: BPS active
1: BPS in standby
0
–
9d
Indicates that no valid integration value could be determined
(measurement value preparation module).
Indicates that measurement
b
range has been exceeded
Range sta(measurement value acquisitus
tion module)
Indicates a position-value output
c
with active static preset or
Preset
dynamic preset (Preset module)
active
Toggle bit, changes during the
d
teach event for the static and
Preset
dynamic preset value (Preset
teach
module)
Rel.
addr.
Data
type
0.0
Bit
0.1
a
Measurement error
Value range
e
Position
limit value
status 1
(static or
dynamic)
f
Position
limit value
status 2
(static or
dynamic)
g
Standby
status
Input data length: 1 byte
Output data
none
68
BPS 34
Leuze electronic
Leuze electronic
Device parameters and interfaces
8.1.7.14 Module 13: Min/Max position
Notice!
Underlined in the CR column are the modules which must be activated in addition to the current module.
Description
The Min/Max position function monitors the position value and transfers the maximum/
minimum value to the PROFIBUS master.
The acquisition time can be adjusted by means of two different modes:
• The "all values" mode detects all values since the start of measurement or since a
reset event.
• The "in measurement value window only" mode only detects extreme values which
occur in the time period defined in the "MinMax period" parameter.
Parameter
Parameter
a
MinMax
mode
b
MinMax
period
Description
Rel.
addr.
Data
type
Value range
Default
Unit
CR to
module
Parameter activates Min/Max
evaluation function.
0
0: Off
unsign 1: All values
8
2: In measurement value
window only
0
–
–
Defines the measurement value
window for the min-max values.
1
unsign
0 … 255
8
10
Measurements
–
TNT 35/7-24V
Parameter length: 2 byte
Hex coding of module 13 "Min/Max position"
Internal address
of module 13
MinMax mode
address 0
MinMax period
address 1
The value listed in the table shows the hex coding of the default settings.
0C
00
0A
Leuze electronic
BPS 34
69
Leuze electronic
Device parameters and interfaces
Input data
Input data
Description
c
Minimum position for
detected period.
0
sign32 -10’000’000 … 10’000’000
d
Maximum position for
Max position detected period.
4
sign32 -10’000’000 … 10’000’000
Min position
Rel.
addr.
Data
type
Value range
Default
Unit
CR to
module
scaled
–
scaled
–
Default
Unit
CR to
module
0
–
7
0
Reset:
2’147’483’647
0
Reset:
-2’147’483’647
Input data length: 8 byte
Output data
Output data
Description
Signal for resetting
e
MinMax reset extreme values
Rel.
addr.
Data
type
0.0
Bit
Value range
0 -> 1: Reset
Output data length: 8 byte
Notice!
With "MinMax reset", the input data are reset to 155812h.
With this module, the settings for the Preset (module 3), Offset (module 5) and Scaling
(module 6) modules must be taken into account.
70
BPS 34
Leuze electronic
Leuze electronic
Device parameters and interfaces
8.1.7.15 Module 14: Static position limit value 1
Description
The limit value function compares the output position value with a position stored during
configuring. If the value is above or below the limit value, the limit value status 1 (module 12)
is set and, if configured, the switching output (module 8) is appropriately set.
Parameter
Parameter
Description
Rel.
addr.
Data
type
Value range
Default
Unit
CR to
module
a
Parameter activates limit
value checking.
0
unsign 0: Off
8
1: On
0
–
7g
b
Condition for the signal
change of the switching output/status bit.
1
unsign 0: Value greater than limit
8
1: Value less than limit
0
–
8d
c
Relative offset of switching
point
2
unsign
0 … 65’535
16
0
mm
–
4
sign32 -10’000’000 … 10’000’000
0
mm
12e
Limit value
mode 1
Switching
mode 1
Hysteresis 1
in [mm]
d
Limit value is compared to the
Limit value 1
current position value.
in [mm]
Parameter length: 8 byte
Hex coding of module 14 "Static position limit value 1"
Limit value mode 1
address 0
Switching mode 1
address 1
Hysteresis 1
address 2
Limit value 1
address 4
0D
00
00
00 00
00 00 00 00
TNT 35/7-24V
Internal address
of module 14
The value listed in the table shows the hex coding of the default settings.
Input data
none
Output data
none
Notice!
With this module, the settings for the Preset (module 3), Offset (module 5) and Scaling
(module 6) modules must be taken into account.
Leuze electronic
BPS 34
71
Leuze electronic
Device parameters and interfaces
8.1.7.16 Module 15: Static position limit value 2
Description
The limit value function compares the output position value with a position stored during
parameterisation. If the value is above or below the limit value, the limit value status 2
(module 12) is set and, if configured, the switching output (module 8) is appropriately set.
Parameter
Parameter
Description
Rel.
addr.
Data
type
Value range
Default
Unit
CR to
module
a
Parameter activates limit
value checking.
0
unsign 0: Off
8
1: On
0
–
7g
b
Condition for the signal
change of the switching output/status bit.
1
unsign 0: Value greater than limit
8
1: Value less than limit
0
–
8d
c
Relative offset of switching
point
2
unsign
0 … 65’535
16
0
mm
–
4
sign32 -10’000’000 … 10’000’000
0
mm
12f
Limit value
mode 2
Switching
mode 2
Hysteresis 2
in [mm]
d
Limit value is compared to the
Limit value 2
current position value.
in [mm]
Parameter length: 8 byte
Hex coding of module 15 "Static position limit value 2"
Internal address
of module 15
Limit value mode 2
address 0
Switching mode 2
address 1
Hysteresis 2
address 2
Limit value 2
address 4
The value listed in the table shows the hex coding of the default settings.
0E
00
00
00 00
00 00 00 00
Input data
none
Output data
none
Notice!
With this module, the settings for the Preset (module 3), Offset (module 5) and Scaling
(module 6) modules must be taken into account.
72
BPS 34
Leuze electronic
Leuze electronic
Device parameters and interfaces
8.1.7.17 Module 16: Dynamic position limit value 1
Description
The limit value function compares the position value with a stored position. If the value is
above or below the limit value, the limit value status 1 in module 12 is set and, if configured,
the switching output is appropriately set.
The limit value is transferred to the BPS 34 together with the output data of this module by
the PROFIBUS master.
Parameter
Parameter
a
Limit value
mode 1
b
Switching
mode 1
Description
Rel.
addr.
Data
type
Value range
Default
Unit
CR to
module
Parameter activates limit value
checking.
0
unsign 0: Off
8
1: On
0
–
7g
Condition for the signal change
of the switching output/status
bit.
1
unsign 0: Value greater than limit
8
1: Value less than limit
0
–
8d
12e
2
unsign
0 … 65’535
16
0
mm
–
Default
Unit
CR to
module
0
mm
–
c
Relative offset of switching
Hysteresis 1
point.
in [mm]
Parameter length: 4 byte
Hex coding of module 16 "Dynamic position limit value 1"
Limit value mode 1
address 0
Switching mode 1
address 1
Hysteresis 1
address 2
0F
00
00
00 00
TNT 35/7-24V
Internal address
of module 16
The value listed in the table shows the hex coding of the default settings.
Input data
none
Output data
Output data
Description
d
Limit value is compared to the
Limit value 1
current position value.
in [mm]
Rel.
addr.
0
Data
type
Value range
sign32 -10’000’000 … 10’000’000
Output data length: 4 byte
Notice!
With this module, the settings for the Preset (module 3), Offset (module 5) and Scaling
(module 6) modules must be taken into account.
Leuze electronic
BPS 34
73
Leuze electronic
Device parameters and interfaces
8.1.7.18 Module 17: Dynamic position limit value 2
Description
The limit value function compares the position value with a stored position. If the value is
above or below the limit value, the limit value status 2 in module 12 is set and, if configured,
the switching output is appropriately set.
The limit value is transferred to the BPS 34 together with the output data of this module by
the PROFIBUS master.
Parameter
Parameter
a
Limit value
mode 2
b
Switching
mode 2
c
Hysteresis 2
in [mm]
Description
Rel.
addr.
Data
type
Value range
Default
Unit
CR to
module
Parameter activates limit
value checking.
0
unsign 0: Off
8
1: On
0
–
7g
Condition for the signal
change of the switching output/status bit.
1
unsign 0: Value greater than limit
8
1: Value less than limit
0
–
8d
12f
Relative offset of switching
point.
2
unsign
0 … 65’535
16
0
mm
–
Default
Unit
CR to
module
0
mm
–
Parameter length: 4 byte
Hex coding of module 17 "Dynamic position limit value 2"
Internal address
of module 17
Limit value mode 2
address 0
Switching mode 2
address 1
Hysteresis 2
address 2
The value listed in the table shows the hex coding of the default settings.
10
00
00
00 00
Input data
none
Output data
Output data
Description
d
Limit value is compared to the
Limit value 2
current position value.
in [mm]
Rel.
addr.
0
Data
type
Value range
sign32 -10’000’000 … 10’000’000
Output data length: 4 byte
Notice!
With this module, the settings for the Preset (module 3), Offset (module 5) and Scaling
(module 6) modules must be taken into account.
74
BPS 34
Leuze electronic
Leuze electronic
Device parameters and interfaces
8.1.7.19 Module 18: Measuring error tolerance
Description
The measuring error tolerance function is used to configure a time which results in an
extended output of the last position value (module 1) in the event of an error. If the position
value changes momentarily to zero, e.g. due to a brief interruption of the laser beam, soiling
of the barcode tape or other short-term disturbances, the BPS transmits the last valid position value.
If the error disappears within the configured time, the control notices nothing or only a small
change in the position value. The availability of the system is thereby ensured. No new
values are delivered by the BPS 34, however, for a period of time extending up to the configured tolerance time. With the "delay error output" parameter, an integration error (corresponds to a missing position value) can be signalled immediately or after the tolerance time
has elapsed. If the error persists after the tolerance time has elapsed, a position value of
zero is output.
Parameter
Parameter
a
Description
Rel.
addr.
Data
type
Value range
Default
Unit
CR to
module
Specifies the time for the output
of the last position value following an error
0
unsign
0 … 65’535
16
50
ms
–
Delays the output of an integrab
Delay error tion error by the configured tolerance time.
output
2
unsign 0: No, error delay deactivated
8
1: Yes, error delay activated
1
–
–
Position
tolerance
time in
[ms]
Parameter length: 3 bytes
TNT 35/7-24V
Hex coding of module 18 "Measuring error tolerance"
Internal address
of module 18
Position
tolerance time
address 0
Delay error output
address 2
The value listed in the table shows the hex coding of the default settings.
14
00 32
01
Input data
none
Output data
none
Leuze electronic
BPS 34
75
Leuze electronic
Device parameters and interfaces
8.1.7.20 Module 19: Service
Description
The "service" function is used to reset the parameter set of the BPS 34 to default settings.
This reset only occurs directly in the BPS 34. After the reset function has been activated, the
device carries out a reset and is freshly configured on the PROFIBUS. This results in the
reactivation of all modules and parameter settings selected in the PROFIBUS project.
Parameter
none
Input data
Input data
Description
Rel.
addr.
a
Shows the state of the reset to
Status byte factory settings
0
Data
type
Value range
Default
Unit
CR to
module
0x00
–
–
Value range
Default
Unit
CR to
module
0 -> 1: Reset the parameters
1 -> 0: Standard operation
0
–
–
0x00: Not active or sucunsign
cessfully concluded
8
0xFF: Reset active
0xF1: EEPROM access error
Input data length: 1 byte
Output data
Output
data
b
Factory
settings
Description
Reset of parameters to factory
settings.
Rel.
addr.
Data
type
0.0
Bit
Output data length: 1 byte
Notice!
The preset function (module 3) must be retaught following a reset.
76
BPS 34
Leuze electronic
Leuze electronic
Device parameters and interfaces
8.1.7.21 Module 20: Velocity
Notice!
Underlined in the CR column are the modules which must be activated in addition to the current module.
Description
Outputs the current velocity with the configured resolution and the desired scaling factor. In
order for the velocity to be calculated in the BPS 34 and output in this module, module 22
(Control velocity) must also be activated in the PROFIBUS project.
Parameter
none
Input data
Input data
a
Velocity
Description
Current velocity
Rel.
addr.
0
Data
Value range
type
unsign
0 … 10’000’000
32
Default
Unit
CR to
module
0
scaled
22
Input data length: 4 byte
Notice!
The scaling of the position value has no effect on the scaling or output of the velocity.
TNT 35/7-24V
The direction of movement of the BPS 34 is displayed in module 23 "Velocity measurement
status" (see page 82) under h "Direction of movement".
Output data
none
Leuze electronic
BPS 34
77
Leuze electronic
Device parameters and interfaces
8.1.7.22 Module 21: Velocity parameters
Description
The velocity parameter influences the fundamental method of operation and output of the
velocity measurement. The resolution, scaling, integration depth and error tolerance for the
velocity measurement can be defined.
The resolution function defines the resolution for the velocity value (module 20). The scaling
function allows the velocity values to be converted to any unit of measurement. To do this,
the velocity value (module 20) is multiplied by the scaling factor. The velocity integration
depth parameter averages the selected number of velocity values to produce the velocity
output in module 20.
The velocity tolerance time function is used to configure a time which results in an extended
output of the last velocity (module 20) in the event of an error. If the speed could not be
calculated momentarily, e.g. due to a brief interruption of the scanning beam, soiling of the
barcode tape or other short-term disturbances, the BPS transmits the last valid velocity. If
the error disappears within the configured time, the control notices nothing or only a small
change in the velocity value. The availability of the system is thereby ensured.
The "delay velocity error output" parameter can be used to signal a velocity error with bit 0.0
either immediately or after the velocity tolerance time in module 23 has elapsed. If the error
persists after the tolerance time has elapsed, a velocity value of zero is output.
Parameter
Parameter
Description
Rel.
addr.
Data
type
Value range
Default
Unit
3
mm/s
1’000
Per
thousand
0
3: 1
unsign 4: 10
8
5: 100
6: 1’000
1
unsign
0 … 65’535
16
3
unsign
2 … 128
8
8
ms
d
Specifies the time for the disVelocity tolplay of the last velocity followerance time
ing an error
in [ms]
4
unsign
0 … 65’535
16
50
ms
e
Delays the output of a velocity
Delay velocerror by the configured tolerity error outance time.
put
6
unsign 0: No, error delay deactivated
8
1: Yes, error delay activated
1
–
a
Velocity res- The parameter specifies the
resolution for the velocity value.
olution in
[mm/s]
b
Scaling factor used to convert
Velocity
the velocity
scaling
factor in [‰]
Number of consecutive measc
urements which are to be used
for velocity determination.
Velocity
integration Specified here is the integration time (see table on
depth
page 79).
CR to
module
20a
23a
Parameter length: 7 bytes
78
BPS 34
Leuze electronic
Leuze electronic
Device parameters and interfaces
Velocity integration depth
Integration time [ms]
1
2
2
4
3
6
4 (default)
8
5
10
:
:
63
126
64
128
Hex coding of module 21 "Velocity parameters"
08
00 32
Delay
velocity error output
address 6
address 4
03 E8
Velocity
tolerance time
Velocity
scaling factor
address 1
03
address 3
Velocity
resolution
address 0
17
Velocity
integration depth
Internal address
of module 21
The value listed in the table shows the hex coding of the default settings.
01
TNT 35/7-24V
Input data
none
Output data
none
Leuze electronic
BPS 34
79
Leuze electronic
Device parameters and interfaces
8.1.7.23 Module 22: Velocity measurement control
Description
The control manages the timing of the velocity measurement by starting or stopping the
measurement function. Control is performed depending on certain events such as the
switching input, time functions or PROFIBUS output bits. Using parameters, it determines
the events which influence the states.
Parameter
Parameter
Description
Rel.
addr.
a
Velocity
measurement start
mode
b
Velocity
measurement stop
mode
The start mode determines by
which event the velocity measurement is started.
0
The stop mode determines after
which event the velocity measurement is stopped.
1
Data
type
Value range
0: Deactivated
1: After initialisation
unsign 2: Following event:
8
either by the switching input
or by a signal from the
PROFIBUS master
0: Deactivated
1: By an error
unsign
2: By a stop event:
8
either by output bit 0.1 or by
the switching input function
Defaul
t
Unit
CR to
module
0
–
7g
0
–
7g
Parameter length: 2 byte
Hex coding of module 22 "Velocity measurement"
80
Internal address
of module 22
Velocity measurement
start mode
address 0
Velocity measurement
stop mode
address 1
The value listed in the table shows the hex coding of the default settings.
18
00
00
BPS 34
Leuze electronic
Leuze electronic
Device parameters and interfaces
Input data
Input data
c
Description
Signals the current state of the
internal velocity measurement
of the BPS 34
State
Rel.
addr.
0
Data
type
Value range
0: Init
unsign 1: Idle
2: Measure
8
4: Standby
Default
Unit
CR to
module
0
–
–
Input data length: 1 byte
Notice!
These input data signal the state of the BPS 34:
•
•
•
•
Init: Base setting during initial startup of the BPS 34
Idle: The BPS 34 is in idle state (scanning beam is off, but motor is running)
Measure: The BPS 34 is in measurement state (data are output in module 1)
Standby: The BPS 34 is in waiting state (laser off and motor off).
Output data
Description
Rel.
addr.
Data
type
Value range
Default
Unit
CR to
module
d
Event starts velocity measurement.
0.0
Bit
0 -> 1: Start
0
–
–
e
Event stops velocity measurement.
0.1
Bit
0 -> 1: Stop
0
–
–
Defines whether the current
velocity is included in min/max
recording.
0.2
Bit
0: Do not record min/max
1: Record min/max
0
–
24
Reset the min/max velocity values.
0.3
Bit
0 -> 1: Reset
0
–
24
Start
event
Stop event
f
Min/Max
velocity
mode
TNT 35/7-24V
Output
data
g
Min/Max
velocity
reset
Output data length: 1 byte
Leuze electronic
BPS 34
81
Leuze electronic
Device parameters and interfaces
8.1.7.24 Module 23: Velocity measurement status
Description
This module supplies various status information regarding the velocity measurement of the
BPS 34 to the PROFIBUS master.
Parameter
none
Input data
Input data
Description
Signals that no valid
velocity could be ascertained.
Signals that velocity limit
b
value 1 has been
Velocity limit
exceeded.
value status 1
Signals that velocity limit
c
value 2 has been
Velocity limit
exceeded.
value status 2
Signals that velocity limit
d
value 3 has been
Velocity limit
exceeded.
value status 3
Signals that velocity limit
e
value 4 has been
Velocity limit
exceeded.
value status 4
Signals that the dynamic
f
velocity limit value has
Dyn. velocity
limit value status been exceeded.
Signals whether a moveg
ment is currently being
Movement status
detected.
If bit 6 is set, the direction
h
of movement can be read
Direction of
here.
movement
Signals whether the curi
rent velocity is compared
Velocity limit
with this limit value.
value status 1
Signals whether the curj
rent velocity is compared
Velocity limit
with this limit value.
value status 2
Signals whether the curk
rent velocity is compared
Velocity limit
with this limit value.
value status 3
Signals whether the curl
rent velocity is compared
Velocity limit
with this limit value.
value status 4
Signals whether the curm
rent velocity is compared
Dyn. velocity
limit value status with this limit value.
a
Velocity measurement error
Rel.
addr.
Data
type
0.0
Bit
0.1
Value range
Default
Unit
CR to
module
0: OK
1: Error
0
–
21
Bit
0: No limit value violation
1: Value greater than limit
0
–
25a
0.2
Bit
0: No limit value violation
1: Value greater than limit
0
–
25a
0.3
Bit
0: No limit value violation
1: Value greater than limit
0
–
25a
0.4
Bit
0: No limit value violation
1: Value greater than limit
0
–
25a
0.5
Bit
0: No limit value violation
1: Value greater than limit
0
–
26b
0.6
Bit
0: No movement
1: Movement
0
–
–
0.7
Bit
0: Direction - tape start
1: Direction - tape end
0
–
–
1.1
Bit
0: Comparison not active
1: Comparison active
0
–
25a
1.2
Bit
0: Comparison not active
1: Comparison active
0
–
25a
1.3
Bit
0: Comparison not active
1: Comparison active
0
–
25a
1.4
Bit
0: Comparison not active
1: Comparison active
0
–
25a
1.5
Bit
0: Comparison not active
1: Comparison active
0
–
26a
Input data length: 2 byte
82
BPS 34
Leuze electronic
Leuze electronic
Device parameters and interfaces
Notice!
The movement status g is displayed for velocities from 0.01 m/s.
Attention!
The "Dynamic preset" module (module 4), the "MVS label" function and the "error tolerance
time" can be used to activate the a … f messages of the input data. Depending on the configuration, these may be normal states.
Output data
TNT 35/7-24V
none
Leuze electronic
BPS 34
83
Leuze electronic
Device parameters and interfaces
8.1.7.25 Module 24: Min/Max velocity
Description
The Min/Max velocity function monitors the velocity value and transfers the maximum and
minimum value to the PROFIBUS master. Recording can be controlled via module 22
"Velocity measurement control". It is also possible to reset values to the initialisation value
via module 22.
Parameter
none
Input data
Input data
Description
Rel.
addr.
Data
type
Value range
Default
Unit
a
Minimum velocity for detected
period.
0
unsign
0 … 10’000’000
32
0
scaled
b
Maximum velocity for detected
period.
4
unsign
0 … 10’000’000
32
0
scaled
Minimum
velocity
Maximum
velocity
CR to
module
22
Input data length: 8 byte
Output data
none
84
BPS 34
Leuze electronic
Leuze electronic
Device parameters and interfaces
8.1.7.26 Module 25: Static velocity limit values
Notice!
Underlined in the CR column are the modules which must be activated in addition to the current module.
Description
The limit value function compares the current velocity with a limit velocity stored in the
configuration. This occurs in the range defined by the range start and end. If a directiondependent limit value check is activated with the "direction selection" parameter, the values
of range start and end define the direction. The check is always performed from range start
to range end. For example, if the range start is 5500 and the range end is 5000, the directiondependent check is only performed in the direction from 5500 to 5000. The limit value is not
active in the opposite direction. If the check is independent of direction, the order of range
start and end is without meaning. If the value is above or below the limit value, the limit value
status in module 23 is set and, if configured, the switching output is appropriately set.
Parameter
Description
a
Parameter activates or deactivates limit value checking for
Velocity limit value 1,
Velocity limit value 2,
Velocity limit value 3,
Velocity limit value 4,
on or off.
Selection of direction-dependent or direction-independent
limit value checking for
Velocity limit value 1,
Velocity limit value 2,
Velocity limit value 3,
Velocity limit value 4,
Condition for the signal change
of the switching output and the
status bits for
Velocity limit value 1,
Velocity limit value 2,
Velocity limit value 3,
Velocity limit value 4,
Velocity
limit value
mode
b
Direction
selection
c
Switching
mode
Rel.
addr.
0.0
0.1
0.2
0.3
for each limit value
0: Limit value not active
1: Limit value activated
0.4
0.5
0.6
0.7
Bits
for each limit value
0: Check in both directions
1: Only check in one direction
1.0
1.1
1.2
1.3
Bits
for each limit value
0: Value greater than limit
1: Value less than limit
2
unsign
0 … 20’000
16
4
unsign
0 … 20’000
16
Leuze electronic
Default
0
0
0
0
Unit
–
0
0
0
0
–
0
0
0
0
–
0
mm/s
CR to
module
8b
22
23b
e
Relative offset of switching
Velocity
hysteresis 1 point.
in [mm/s]
Value range
Bits
d
Limit value is compared to the
Velocity
limit value 1 current velocity.
in [mm/s]
Data
type
TNT 35/7-24V
Parameter
BPS 34
0
mm/s
85
Leuze electronic
Device parameters and interfaces
f
Range start The velocity limit value is monilimit value 1 tored beginning at this position.
in [mm]
6
sign32 -10’000’000 … 10’000’000
0
mm
23b
g
Range end The velocity limit value is monilimit value 1 tored up to this position.
in [mm]
10
sign32 -10’000’000 … 10’000’000
0
mm
14
unsign
0 … 20’000
16
0
mm/s
16
unsign
0 … 20’000
16
0
mm/s
h
Limit value is compared to the
Velocity
limit value 2 current velocity.
in [mm/s]
i
Relative offset of switching
Velocity
hysteresis 2 point.
in [mm/s]
23c
j
Range start The velocity limit value is monilimit value 2 tored beginning at this position.
in [mm]
18
sign32 -10’000’000 … 10’000’000
0
mm
22
sign32 -10’000’000 … 10’000’000
0
mm
26
unsign
0 … 20’000
16
0
mm/s
28
unsign
0 … 20’000
16
0
mm/s
k
Range end The velocity limit value is monilimit value 2 tored up to this position.
in [mm]
l
Limit value is compared to the
Velocity
limit value 3 current velocity.
in [mm/s]
m
Relative offset of switching
Velocity
hysteresis 3 point.
in [mm/s]
23d
n
Range start The velocity limit value is monilimit value 3 tored beginning at this position.
in [mm]
30
sign32 -10’000’000 … 10’000’000
0
mm
34
sign32 -10’000’000 … 10’000’000
0
mm
38
unsign
0 … 20’000
16
0
mm/s
40
unsign
0 … 20’000
16
0
mm/s
42
sign32 -10’000’000 … 10’000’000
0
mm
o
Range end The velocity limit value is monilimit value 3 tored up to this position.
in [mm]
p
Limit value is compared to the
Velocity
limit value 4 current velocity.
in [mm/s]
23e
q
Relative offset of switching
Velocity
hysteresis 4 point.
in [mm/s]
r
Range start The velocity limit value is monilimit value 4 tored beginning at this position.
in [mm]
23e
s
Range end The velocity limit value is monilimit value 4 tored up to this position.
in [mm]
46
sign32 -10’000’000 … 10’000’000
0
mm
Parameter length: 50 bytes
86
BPS 34
Leuze electronic
Velocity
hysteresis 4
address 40
Range start
limit value 4
address 42
Range end
limit value 4
address 46
Velocity
limit value 2
address 14
Velocity
hysteresis 2
address 16
Range start
limit value 2
address 18
Range end
limit value 2
address 22
Velocity
limit value 3
address 26
Velocity
hysteresis 3
address 28
Range start
limit value 3
address 30
Range end
limit value 3
address 34
Internal address of module 25
Velocity limit
value mode
address 0
Direction selection
address 0
Switching mode
address 1
Velocity
limit value 1
address 2
Velocity
hysteresis 1
address 4
Range start
limit value 1
address 6
Range end
limit value 1
address 10
1B
00
00
00
00 00
00 00
00 00 00 00
00 00 00 00
00 00
00 00
00 00 00 00
00 00 00 00
Input data
none
Leuze electronic
BPS 34
TNT 35/7-24V
Velocity
limit value 4
address 38
Leuze electronic
Device parameters and interfaces
Hex coding of module 25 "Static velocity limit values"
The value listed in the table shows the hex coding of the default settings.
00 00
00 00
00 00 00 00
00 00 00 00
00 00
00 00
00 00 00 00
00 00 00 00
Output data
none
87
Leuze electronic
Device parameters and interfaces
8.1.7.27 Module 26: Dynamic velocity limit value
Notice!
Underlined in the CR column are the modules which must be activated in addition to the current module.
Description
The velocity limit value function compares the current velocity with a stored velocity within
the defined range. If the value is above or below the limit value, the dynamic limit value
status in module 23 is set and, if configured, the switching output is appropriately set. Limit
value, hysteresis, range start and range end are transferred with the output data of this
module by the PROFIBUS master. The transferred values are activated by bit 0.0, i.e. if this
bit is set, the BPS 34 compares the current velocity with the new limit value conditions.
Parameter
none
Input data
none
88
BPS 34
Leuze electronic
Leuze electronic
Device parameters and interfaces
Output data
Output data
Description
a
Controls internal processing
of the transferred dynamic
limit value parameters.
Condition for the signal
change of the switching output
and the status bit for dynamic
velocity limit value.
Selection of direction-dependent or direction-independent
limit value checking for
dynamic velocity limit value
Limit value
control
b
Switching
mode
c
Direction
selection
Rel.
addr.
Data
type
0.0
Bit
0.1
0.2
d
Limit value is compared to the
Dyn. velocity limit value current velocity.
in [mm/s]
f
The dynamic velocity limit
Range start
value is monitored beginning
dyn. limit
at this position.
value in [mm]
Default
Unit
0: Do not process
1: Parameter now valid /
process
0
–
Bit
0: Value greater than limit
1: Value less than limit
0
–
Bits
0: Check in both directions
1: Only check in one direction
0
–
1
unsign
0 … 20’000
16
0
mm/s
3
unsign
0 … 20’000
16
0
mm/s
5
sign32 -10’000’000 … 10’000’000
0
mm
9
sign32 -10’000’000 … 10’000’000
0
mm
e
Relative offset of switching
Dyn. velocity hysteresis point.
in [mm/s]
Value range
g
The dynamic velocity limit
Range end
value is monitored up to this
dyn. limit
position.
value in [mm]
CR to
module
8d
22
23f
23m
8d
22
23f
23m
TNT 35/7-24V
Output data length: 13 byte
Leuze electronic
BPS 34
89
Leuze electronic
Device parameters and interfaces
8.1.7.28 Module 27: Tape value correction
Description
The tape value correction function can be used to correct the length deviation of the barcode
tape length from the actual tape length (calibration) which results from the production
process. For this purpose, a suitable measuring device must be used to determine the actual
length of one metre of barcode tape (as printed). If, for example, one metre of tape has an
absolute value of 1001.4 millimetres, the value 10014 is entered in the "real length" parameter of this module. The real length is specified with a resolution of 0.1 millimetres. To use
the exact resolution, it is useful to measure a longer section of barcode tape and convert the
deviation to a length of one metre.
Nominal length: 1000.0 mm
1 m barcode tape
000000
000004
000008
000012
000016
000020
000024
000028
000036
000032
000040
000044
000048
000052
000056
000060
000064
000068
000072
000076
000080
000084
000088
000092
000096
000100
measured actual length: 1001.4 mm
§ real length in [mm/10] = 10014
Figure 8.29: Tape value correction
The "range start" parameter must be configured according to the real starting value of the
used barcode tape. If several different barcode tapes are connected to one another in
sequence, the "range end" of the corrected tape section must also be entered. The entire
barcode tape is corrected with the default value of 10’000’000 for the range end.
Parameter
Parameter
Description
Specifies the real (calibrated)
a
Real length length of one metre of barcode
in [mm/10] tape (as printed).
Rel.
addr.
Data
type
Value range
Default
Unit
CR to
module
10’000
mm/10
1
0
unsign
0 … 65’535
16
The tape value is corrected with
the real length starting from this
position.
2
sign32 0 … 10’000’000
0
mm
–
The tape value is corrected with
c
Range end the real length up to this position.
in [mm]
6
sign32 0 … 10’000’000
10’000’000
mm
–
b
Range
start in
[mm]
Parameter length: 10 bytes
90
BPS 34
Leuze electronic
Leuze electronic
Device parameters and interfaces
Hex coding of module 27 "Tape value correction"
Internal address
of module 27
Real length
address 0
Range start
address 2
Range end
address 6
The value listed in the table shows the hex coding of the default settings.
1D
27 10
00 00 00 00
00 98 96 80
Input data
none
Output data
TNT 35/7-24V
none
Leuze electronic
BPS 34
91
Leuze electronic
Diagnostics and troubleshooting
9
Diagnostics and troubleshooting
9.1
General causes of errors
Error
LED MS 34 10x =
"off"
LED MS 34 10x =
"flashes red"
LED MS 34 10x =
"red continuous light"
(no communication via
PROFIBUS)
LED MS 34 10x =
"orange continuous
light"
Position error
9.2
Possible error cause
• No supply voltage connected to
the device.
• Device not yet recognised by the
PROFIBUS
Notice: The LED remains off until
the BPS 34 is recognised by the
PROFIBUS. Only after the
PROFIBUS has addressed the
BPS 34 for the first time do the
following status descriptions
apply.
• Error on the PROFIBUS.
•
•
•
•
•
Incorrect wiring.
Wrong termination.
Incorrect PROFIBUS address set.
PROFIBUS deactivated.
Incorrect configuration.
❏ Check PROFIBUS settings.
❏ Reset device
❏
❏
❏
❏
❏
(switch voltage on/off).
Check wiring.
Check termination.
Check PROFIBUS address.
Activate PROFIBUS interface.
Check configuration of the device in the configuration tool.
Reduce number of modules.
• Parameter-memory overflow in
the control.
❏
• Service operation active.
❏ Set the service switch in MSD 1 101 to
• No barcode tape present.
• Scanner positioned in total reflection
• Scanner not properly mounted
❏ Check positioning of barcode tape.
❏ Change the angle of the scanning beam by
"Operation"
tilting the BPS 34.
❏ Check mounting.
PROFIBUS errors
Error
Sporadic errors at the
PROFIBUS
Possible error cause
• Incorrect wiring.
• Wrong termination.
• Electromagnetic influences.
• Overall network expansion
exceeded.
92
Measures
❏ Check supply voltage.
BPS 34
❏
❏
❏
❏
❏
Measures
Check wiring.
Check termination.
Check shielding.
Check grounding concept and connection to
FE.
Check max. network expansion as a function of the set baud rate.
Leuze electronic
Leuze electronic
Diagnostics and troubleshooting
Notice!
Please use page 92 and page 93 as a master copy should servicing be required.
Cross the items in the "Measures" column which you have already examined, fill out the following address field and fax both pages together with your service contract to the fax
number listed below.
Customer data (please complete) Leuze service fax number: +49 7021 573-199
Device type:
Company:
Contact partner / department:
Phone (direct):
Fax:
Street / No:
ZIP code/City:
TNT 35/7-24V
Country:
Leuze electronic
BPS 34
93
Leuze electronic
Type overview and accessories
10
Type overview and accessories
10.1
Type overview: BPS 34
Part No.
50038007
50038008
50103179
10.2
Type designation
MSD 1 101
KB 034-2000
Remark
Modular Service Display for BPS 34
Connection cable MS 34 105 to MSD 1 101
Type designation
TS 02-4-SA
Remark
M 12 connector with integrated terminating resistor for DP OUT (B-coded)
Type designation
KD 02-5-BA
KD 02-5-SA
KD 095-5A
Remark
M 12 socket connector for DP IN (B-coded)
M 12 plug connector for DP OUT (B-coded)
M 12 connector for voltage supply (A-coded)
Accessory mounting device
Part No.
50027375
94
Remark
Modular hood with integrated connectors for BPS 34 with three M 12 connectors
Modular hood with integrated connectors for BPS 34 with five M 12 connectors
Accessory connectors
Part No.
50038538
50038537
50020501
10.6
Type designation
MS 34 103
MS 34 105
Accessory termination
Part No.
50038539
10.5
PROFIBUS DP interface, max. temp up to 50 °C
Accessory modular service display
Part No.
50037232
50037543
10.4
Remark
PROFIBUS DP interface
PROFIBUS DP interface and heating
Accessory modular hoods with integrated connectors
Part No.
50037230
50037231
10.3
Type designation
BPS 34 S M 100
BPS 34 S M 100 H
BPS 34 S M 100
HT
Type designation
BT 56
Remark
Mounting device with dovetail and rod
BPS 34
Leuze electronic
Leuze electronic
Type overview and accessories
10.7
Accessory ready-made cables for voltage supply
10.7.1
Contact assignment of PWR IN connection cable
PWR connection cable (5-pin socket, A-coded)
PWR IN
Pin
Name
Core colour
SWOUT
2
1
VIN
brown
2
SWOUT
white
GND 3
PE
blue
SWIN
black
5
PE
grey
Thread
PE
bare
Specifications of voltage supply cable
Operating temperature range
in rest state: -30°C … +70°C
in motion: -5°C … +70°C
Material
Sheathing: PVC
Bending radius
> 50 mm
Order codes for voltage supply cables
Part No.
50104557
50104559
Leuze electronic
Type designation
Remark
K-D M12A-5P-5m-PVC
M 12 socket for PWR IN, axial connector, open line end, cable length 5 m
K-D M12A-5P-10m-PVC M 12 socket for PWR IN, axial connector, open line end, cable length 10 m
BPS 34
95
TNT 35/7-24V
10.7.3
GND
4
4
SWIN
M 12 socket
(A-coded)
10.7.2
3
1 VIN
Leuze electronic
Type overview and accessories
10.8
Accessory ready-made cables for PROFIBUS connection
10.8.1
General
• Cable KB PB… for connecting to the DP IN/DP OUT M 12 connector
• Standard cables available in lengths from 2 … 30m
• Special cables on request.
10.8.2
Contact assignment for PROFIBUS connection cable KB PB…
PROFIBUS connection cable (5-pin socket/connector, B-coded)
Pin
A (N)
2
N.C. 1
3 N.C.
4
N.C.
B (P)
M 12 socket
(B-coded)
Name
Core colour
1
N.C.
–
2
A (N)
green
3
N.C.
–
4
B (P)
red
5
N.C.
–
Thread
FE
bare
A (N)
2
N.C.
3
N.C.
1 N.C.
4
B (P)
M 12 plug
(B-coded)
1
2
3
4
Conductor with insulation red
Conductor with insulation green
Drain wire
Fibrous fleece
Figure 10.1:Cable structure of PROFIBUS connection cable
96
BPS 34
Leuze electronic
Leuze electronic
10.8.4
Specifications of PROFIBUS connection cable
Operating temperature range
in rest state: -40°C … +80°C
in motion: -5°C … +80°C
Material
The lines fulfil the PROFIBUS requirements,
free of halogens, silicone and PVC
Bending radius
> 80 mm, suitable for drag chains
Order codes for PROFIBUS connection cables
Part No.
50104181
50104180
50104179
50104178
50104177
50104176
50104175
Type designation
KB PB-2000-BA
KB PB-5000-BA
KB PB-10000-BA
KB PB-15000-BA
KB PB-20000-BA
KB PB-25000-BA
KB PB-30000-BA
Remark
M 12 socket for DP IN, axial connector, open line end, cable length 2 m
M 12 socket for DP IN, axial connector, open line end, cable length 5 m
M 12 socket for DP IN, axial connector, open line end, cable length 10 m
M 12 socket for DP IN, axial connector, open line end, cable length 15 m
M 12 socket for DP IN, axial connector, open line end, cable length 20 m
M 12 socket for DP IN, axial connector, open line end, cable length 25 m
M 12 socket for DP IN, axial connector, open line end, cable length 30 m
50104188
50104187
50104186
50104185
50104184
50104183
50104182
KB PB-2000-SA
KB PB-5000-SA
KB PB-10000-SA
KB PB-15000-SA
KB PB-20000-SA
KB PB-25000-SA
KB PB-30000-SA
M 12 plug for DP OUT, axial connector, open line end, cable length 2 m
M 12 plug for DP OUT, axial connector, open line end, cable length 5 m
M 12 plug for DP OUT, axial connector, open line end, cable length 10 m
M 12 plug for DP OUT, axial connector, open line end, cable length 15 m
M 12 plug for DP OUT, axial connector, open line end, cable length 20 m
M 12 plug for DP OUT, axial connector, open line end, cable length 25 m
M 12 plug for DP OUT, axial connector, open line end, cable length 30 m
50104096
50104097
50104098
50104099
50104100
50104101
50104174
50104173
KB PB-1000-SBA
KB PB-2000-SBA
KB PB-5000-SBA
KB PB-10000-SBA
KB PB-15000-SBA
KB PB-20000-SBA
KB PB-25000-SBA
KB PB-30000-SBA
M 12 plug, M 12 socket for PROFIBUS, axial connectors, cable length 1 m
M 12 plug, M 12 socket for PROFIBUS, axial connectors, cable length 2 m
M 12 plug, M 12 socket for PROFIBUS, axial connectors, cable length 5 m
M 12 plug, M 12 socket for PROFIBUS, axial connectors, cable length 10 m
M 12 plug, M 12 socket for PROFIBUS, axial connectors, cable length 15 m
M 12 plug, M 12 socket for PROFIBUS, axial connectors, cable length 20 m
M 12 plug, M 12 socket for PROFIBUS, axial connectors, cable length 25 m
M 12 plug, M 12 socket for PROFIBUS, axial connectors, cable length 30 m
Leuze electronic
BPS 34
97
TNT 35/7-24V
10.8.3
Type overview and accessories
Leuze electronic
Type overview and accessories
10.9
Type overview: Barcode tape
Part No.
50038895
50040041
50037489
50037491
50037492
50038894
50038893
50038892
50038891
50038890
50037493
50040042
50040043
50040044
50040045
50040046
50037494
50037495
50102600
98
Type designation
BCB 005
BCB 010
BCB 020
BCB 030
BCB 040
BCB 050
BCB 060
BCB 070
BCB 080
BCB 090
BCB 100
BCB 110
BCB 120
BCB 130
BCB 140
BCB 150
BCB 200
BCB / special lengths starting at 150 m
BCB special length 25 mm high
BPS 34
Remark
Barcode tape, 5 m long
Barcode tape, 10 m long
Barcode tape, 20 m long
Barcode tape, 30 m long
Barcode tape, 40 m long
Barcode tape, 50 m long
Barcode tape, 60 m long
Barcode tape, 70 m long
Barcode tape, 80 m long
Barcode tape, 90 m long
Barcode tape, 100 m long
Barcode tape, 110 m long
Barcode tape, 120 m long
Barcode tape, 130 m long
Barcode tape, 140 m long
Barcode tape, 150 m long
Barcode tape, 200 m long
Barcode tape with special length and special height
Barcode tape with special length 25 mm high
Leuze electronic
Leuze electronic
Maintenance
11
Maintenance
11.1
General maintenance information
Usually, the BPS 34 does not require any maintenance by the operator.
In the event of dust build-up, clean the optical window with a soft cloth; use a cleaning agent
(commercially available glass cleaner) if necessary.
Also check the barcode tape for possible soiling.
Attention!
Do not use solvents and cleaning agents containing acetone. Use of improper cleaning
agents can damage the optical window.
11.2
Repairs, servicing
Repairs to the device must only be carried out by the manufacturer.
! Contact your Leuze distributor or service organisation should repairs be required.
The addresses can be found on the inside of the cover and on the back.
Notice!
When sending devices to Leuze electronic for repair, please provide an accurate description
of the error.
Disassembling, packing, disposing
Repacking
For later re-use, the device is to be packed so that it is protected.
Notice!
Electrical scrap is a special waste product! Observe the locally applicable regulations regarding disposal of the product.
Leuze electronic
BPS 34
99
TNT 35/7-24V
11.3
Leuze electronic
Appendix
12
Appendix
12.1
EU Declaration of Conformity
100
BPS 34
Leuze electronic
Leuze electronic
Index
A
Absolute accuracy . . . . . . . . . . . . . . . . . .30
Accessories . . . . . . . . . . . . . . . . . . . 22, 94
Connectors . . . . . . . . . . . . . . . . . . . . .94
Modular hoods w. integrated connectors .94
Modular service display . . . . . . . . . . . .94
Mounting device . . . . . . . . . . . . . . . . .94
Ready-made cables . . . . . . . . . . . 95, 96
Termination . . . . . . . . . . . . . . . . . . . . .94
Actual length . . . . . . . . . . . . . . . . . . . . . .90
Air pockets . . . . . . . . . . . . . . . . . . . . . . .30
Angle of inclination . . . . . . . . . . . . . . . 9, 39
Areas of application . . . . . . . . . . . . . . . . . .6
B
Barcode tape . . . . . . .
Cut mark . . . . . . . .
defective . . . . . . . .
Repair kit . . . . . . .
Type overview . . . .
Wrapping direction .
Beam exit . . . . . . . . .
Bonding surface . . . . .
BPS Configuration Tool
Bus address . . . . . . .
Bus termination . . . . .
. . . . . . . . . . . . . . .27
. . . . . . . . . . . . . . .29
. . . . . . . . . . . . . . .35
. . . . . . . . . . . . . . .35
. . . . . . . . . . . . . . .98
. . . . . . . . . . . . . . .27
. . . . . . . . . . . . 8, 40
. . . . . . . . . . . . . . .30
. . . . . . . . . . . . . . .25
. . . . . . . . . . . 10, 45
. . . . . . . . . . . . . . .19
C
Cable
PROFIBUS connection . . . . . . . . . . . . .96
Voltage supply . . . . . . . . . . . . . . . . . . .95
Calibration . . . . . . . . . . . . . . . . . . . . . . . .90
Caps . . . . . . . . . . . . . . . . . . 17, 18, 19, 43
Causes of errors . . . . . . . . . . . . . . . . . . . .92
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . .16
Cleaning agents . . . . . . . . . . . . . . . . . . . .99
Commissioning steps at a glance . . . . . . . . .8
Configuration tool . . . . . . . . . . . . . . . . . . .45
Connection . . . . . . . . . . . . . . . . . . . . . . .16
Accessories . . . . . . . . . . . . . . . . . . . .22
Functional earth PE . . . . . . . . . . . . . . .18
Modular Service Display . . . . . . . . . . . .12
MSD 1 101 . . . . . . . . . . . . . . . . . . . . .26
PROFIBUS . . . . . . . . . . . . . . . . . 10, 42
Switching input . . . . . . . . . . . . . . . . . .11
Switching output . . . . . . . . . . . . . . . . .11
Leuze electronic
Voltage supply . . . .
Connection assignment
Connector unit . . . . . .
Control barcode . . . . .
MVS . . . . . . . . . . .
Positioning . . . . . .
Structure . . . . . . . .
Core cross section . . .
Count direction . . . . . .
cUL . . . . . . . . . . . . . .
Curves . . . . . . . . . . .
Cut mark . . . . . . . . . .
............... 9
. . . . . . . . . . . . . . 17
. . . . . . . . . . . . . . 22
. . . . . . . . . . . . . . 32
. . . . . . . . . . . . . . 33
. . . . . . . . . . . . . . 33
. . . . . . . . . . . . . . 32
. . . . . . . . . . . . . . 18
. . . . . . . . . . . . . . 67
............... 3
. . . . . . . . . . . . . . 31
. . . . . . . . . . . . . . 29
D
DC bias level . . . . . . . . . .
Debounce time . . . . . . . . .
Declaration of conformity . .
Default settings . . . . . . . .
Description of functions . . .
Device arrangement . . . . .
Device parameters . . . . . .
Diagnosis . . . . . . . . . . . .
Dimensioned drawing
Connector unit . . . . . . .
Modular Service Display
MS 34 105 . . . . . . . . . .
MS 34 103 . . . . . . . . . .
MSD 1 101 . . . . . . . . .
Dimensioned drawings
BPS 34 . . . . . . . . . . . .
MS 34 105 . . . . . . . . . .
MS 34 103 . . . . . . . . . .
Direction of movement . . . .
Disassembling . . . . . . . . .
Disposing . . . . . . . . . . . .
Double insulation . . . . . . .
Download . . . . . . . . . . . .
GSE file . . . . . . . . . . .
DP IN . . . . . . . . . . . . . . .
DP OUT . . . . . . . . . . . . .
Dust . . . . . . . . . . . . . . . .
. . . . . . . . . . . 61
. . . . . . . . . . . 59
. . . . . . . . 3, 100
. . . . . . . . . . . 76
............ 4
. . . . . . . . . 8, 40
. . . . . . . . . . . 42
. . . . . . . . . . . 92
...........
...........
...........
...........
...........
23
26
23
23
26
...........
...........
...........
...........
...........
...........
...........
...........
...........
. . . . . . . . 19,
. . . . . . . . 19,
...........
14
15
15
66
99
99
16
30
45
43
43
99
E
Electrical connection . . . . . . . . . . . . . . . . 16
Error
on PROFIBUS . . . . . . . . . . . . . . . . . . 92
BPS 34
101
Leuze electronic
Index
Error case . . . . . . . . . . . . .
Error output . . . . . . . . . . . .
EU Declaration of Conformity
Expansion joints . . . . . . . . .
. . . . . . . . . . .75
. . . . . . . . . . .75
. . . . . . . . . .100
. . . . . . . . . . .30
F
Factory settings . . . . . . . . . . . . . . . . . . . .76
Fastening grooves . . . . . . . . . . . . . . . . . .37
Faults . . . . . . . . . . . . . . . . . . . . . . . . . . .16
G
Gap . . . . . .
GSE file . . .
GSE modules
Overview
Structure .
. . . . . . . . . . . . . . . . . . . . . .29
. . . . . . . . . . . . . . . . . . 42, 45
. . . . . . . . . . . . . . . . . . . . . .47
. . . . . . . . . . . . . . . . . . . . . .46
H
Heating
Integrated . . . . . . . . . . . . . . . . . . 18, 41
Hood with integrated connectors . . . . . . . .22
I
Input data . . . . .
Integrated heating
Integration depth
Integration error .
Integration time .
Intended use . . .
Interface
PROFIBUS . .
. . . . . . . . . . . . . . . . . . .42
. . . . . . . . . . . . . . . . . .41
. . . . . . . . . . . . . . . 66, 78
. . . . . . . . . . . . . . . . . . .75
. . . . . . . . . . . . . . . . . . .79
. . . . . . . . . . . . . . . . . . . .5
. . . . . . . . . . . . . . . . . . .42
L
Laser radiation .
LED states . . . .
Length deviation
Limit value . . . .
Limit velocity . .
Limits . . . . . . .
. . . . . . . . . . . . . . . . . . . . .6
. . . . . . . . . . . . . . . . . . . .24
. . . . . . . . . . . . . . . . . . . .90
. . . . . . . 71, 72, 73, 74, 85
. . . . . . . . . . . . . . . . . . . .85
. . . . . . . . . . . . . . . . . . . .68
M
Maintenance . . . . . . . . . . . . . . . . . . . . . .99
Maximum velocity . . . . . . . . . . . . . . . . . . .84
102
Measurement error . . . . . . . . . . . . . . . . . 68
Measurement length . . . . . . . . . . . . . . . . 65
Measurement start mode . . . . . . . . . . . . . 63
Velocity . . . . . . . . . . . . . . . . . . . . . . . 80
Measurement stop mode . . . . . . . . . . . . . 63
Velocity . . . . . . . . . . . . . . . . . . . . . . . 80
Measurement value switching . . . . . . . . . 33
Measuring error tolerance . . . . . . . . . . . . 75
Minimum velocity . . . . . . . . . . . . . . . . . . 84
Modular hood with integrated connectors
MS 34 103 . . . . . . . . . . . . . . . . . . . . 22
Modular Service Display . . . . . . . . . . . . . 25
Module
Control . . . . . . . . . . . . . . . . . . . . . . . 63
Dynamic position limit value 1 . . . . . . . 73
Dynamic position limit value 2 . . . . . . . 74
Dynamic preset . . . . . . . . . . . . . . . . . 55
Dynamic velocity limit value . . . . . . . . . 88
Measurement value acquisition . . . . . . 65
Measurement value preparation . . . . . . 66
Measuring error tolerance . . . . . . . . . . 75
Min/Max position . . . . . . . . . . . . . . . . 69
Min/Max velocity . . . . . . . . . . . . . . . . 84
Offset value . . . . . . . . . . . . . . . . . . . . 56
Position value . . . . . . . . . . . . . . . . . . 51
Resolution . . . . . . . . . . . . . . . . . . . . . 52
Scaling . . . . . . . . . . . . . . . . . . . . . . . 57
Service . . . . . . . . . . . . . . . . . . . . . . . 76
Static position limit value 1 . . . . . . . . . 71
Static position limit value 2 . . . . . . . . . 72
Static preset . . . . . . . . . . . . . . . . . . . 53
Static velocity limit values . . . . . . . . . . 85
Status . . . . . . . . . . . . . . . . . . . . . . . . 68
Switching input . . . . . . . . . . . . . . . . . 59
Switching output . . . . . . . . . . . . . . . . 61
Tape value correction . . . . . . . . . . . . . 90
Velocity . . . . . . . . . . . . . . . . . . . . . . . 77
Velocity measurement control . . . . . . . 80
Velocity measurement status . . . . . . . . 82
Velocity parameters . . . . . . . . . . . . . . 78
Modules . . . . . . . . . . . . . . . . . . . . . . . . 47
Mounting . . . . . . . . . . . . . . . . . . . . . . . . 37
Angle of inclination . . . . . . . . . . . . . . . 39
Barcode tape . . . . . . . . . . . . . . 8, 29, 41
BPS 34 . . . . . . . . . . . . . . . . . . . . . . . 37
BT 56 . . . . . . . . . . . . . . . . . . . . . . . . 37
Device . . . . . . . . . . . . . . . . . . . . . . . . 8
Mounting device . . . . . . . . . . . . . . . . . 37
BPS 34
Leuze electronic
Leuze electronic
Outdoors . . . . .
Mounting device
BT 56 . . . . . . .
Mounting example
Mounting location .
Mounting surface .
Moving system . . .
MS 34 103 . . . . . .
MSD 1 101 . . . . .
MVS . . . . . . . . . .
Index
. . . . . . . . . . . . . . . . . .41
. . . . . . . . . . . . . . . . . .37
. . . . . . . . . . . . . . . . . .39
. . . . . . . . . . . . . . . . . .40
. . . . . . . . . . . . . . . . . .30
. . . . . . . . . . . . . . . . . . .9
. . . . . . . . . . . . . . . . . .22
. . . . . . . . . . . . . . . . . .25
. . . . . . . . . . . . . . . . . .33
N
Name plate . . . . . . . . . . . . . . . . . . . . 7, 16
Nominal length . . . . . . . . . . . . . . . . . . . . .90
O
Optical window . . . . . . . . . . . .
Order codes
PROFIBUS connection cable
Voltage supply cable . . . . .
Output data . . . . . . . . . . . . . .
Overview
Modules . . . . . . . . . . . . . .
. . . . . . . . .99
. . . . . . . .97
. . . . . . . . .95
. . . . . . . . .42
. . . . . . . . .47
P
Packing . . . . . . . . .
Parameter memory .
Position limit value .
Position value . . . .
Positioning
Control barcode .
Power supply unit . .
Preset value . . . . .
PROFIBUS . . . . . .
Address . . . . . .
Communication .
DP . . . . . . . . . .
Error . . . . . . . . .
GSE file . . . . . .
Incoming . . . . . .
Outgoing . . . . . .
Project . . . . . . .
PROFIBUS address
PROFIBUS manager
Protection class . . .
Leuze electronic
. . . . . . . . . . . . . . . . .99
. . . . . . . . . . . . . . . . .25
. . . . . . . 71, 72, 73, 74
. . . . . . . . . . . . . . . . .51
. . . . . . . . . . . . . . . . .33
. . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . 53, 55
. . . . . . . . . . . . . . . . .42
. . . . . . . . . . . . . . . . .45
. . . . . . . . . . . . . . . . .24
. . . . . . . . . . . . . . . . .42
. . . . . . . . . . . . . . . . .92
. . . . . . . . . . . . . . . . .42
. . . . . . . . . . . . . 19, 43
. . . . . . . . . . . . . 19, 43
. . . . . . . . . . . . . . . . .25
. . . . . . . . . . . . . . . . .10
. . . . . . . . . . . . . . . .11
. . . . . . . 17, 18, 19, 43
protective conductor
Protective housing .
Pulse duration . . . .
PWR IN . . . . . . . . .
................
................
. . . . . . . . . . . . . 59,
................
16
41
61
18
Q
Quality assurance . . . . . . . . . . . . . . . . . . . 3
R
Range end . . . . .
Range start . . . .
Reading field
Curve . . . . . .
Read distance
Width . . . . . .
Working range
Real length . . . .
Repair . . . . . . . .
Repair kit . . . . . .
Download . . .
Reset . . . . . . . .
Resolution . . . . .
Rod mounting . . .
Rotary switch . . .
. . . . . . . . . . . . . . . . . . 90
. . . . . . . . . . . . . . . . . . 90
..................
..................
..................
..................
..................
. . . . . . . . . . . . . . . . 5,
..................
..................
..................
..................
..................
..................
21
21
21
21
90
99
35
35
76
52
37
10
S
Safety notices . . . . .
Safety transformer . .
Scaling . . . . . . . . . .
Scaling factor . . . . . .
Service . . . . . . . . . .
Service fax . . . . . . . .
Service interface . . . .
Service order . . . . . .
Servicing . . . . . . . . .
Slide switch . . . . . . .
Soiling . . . . . . . . . . .
Specifications . . . . . .
Barcode tape . . . .
Connector units . .
Electrical data . . .
Environmental data
Measurement data
Mechanical data . .
Optical data . . . . .
BPS 34
................ 5
. . . . . . . . . . . . . . . 16
. . . . . . . . . . . . . . . 78
. . . . . . . . . . . . . . . 57
. . . . . . . . . . . . . . . 76
. . . . . . . . . . . . . . . 93
. . . . . . . . . . . . 24, 25
. . . . . . . . . . . . . . . 93
. . . . . . . . . . . . . . . 99
. . . . . . . . . . . . . . . 10
. . . . . . . . . . . . . . . 41
. . . . . . . . . . . . . . . 13
. . . . . . . . . . . . 14, 28
. . . . . . . . . . . . . . . 22
. . . . . . . . . . . . . . . 13
. . . . . . . . . . . . . . 13
. . . . . . . . . . . . . . . 13
. . . . . . . . . . . . . . . 13
. . . . . . . . . . . . . . . 13
103
Leuze electronic
Index
PROFIBUS connection cable
Voltage supply cable . . . . .
Start-up delay . . . . . . . . . . . .
Status
PROFIBUS . . . . . . . . . . . .
Status information . . . . . . . . .
Status LED . . . . . . . . . . . . . .
Sub-D connector . . . . . . . . . .
Supply voltage . . . . . . . . . . . .
SW IN/OUT . . . . . . . . . . . . . .
Switching input . . . . . . . . . . . .
Switching output . . . . . . . . . . .
Switch-off delay . . . . . . . . . . .
Switch-off function . . . . . . . . .
Switch-on function . . . . . . . . .
Symbols . . . . . . . . . . . . . . . .
T
Tape height . . . . . . . . . .
Tape switching . . . . . . . .
Tape value correction . . .
Termination
Connector TS 02-4-SA
Total reflection . . . . . . . .
Troubleshooting . . . . . . .
Type overview . . . . . . . .
Barcode tape . . . . . . .
BPS 34 . . . . . . . . . . .
. . . . . . . .97
. . . . . . . . .95
. . . . . . . . .59
. . . . . . . . .24
. . . . . 68, 82
. . . . . . . . .24
. . . . . . . . .26
. . . . . . . . .16
. . . . . . . . .20
. . . . . 20, 59
. . . . . . . . .20
. . . . . . . . .60
. . . . . . . . .62
. . . . . . . . .61
. . . . . . . . . .3
. . . . . . . . . . 9, 39
. . . . . . . . . . . . .34
. . . . . . . . . . . . .90
. . . . . . . . . . . . .19
. . . . . . . . . . . . .40
. . . . . . . . . . . . .92
. . . . . . . . . . . . .94
. . . . . . . . . . . . .98
. . . . . . . . . . . . .94
U
Universal module . . . . . . . . . . . . . . . . . . .46
V
Velocity . . . . . . . . . .
Velocity limit value . .
Velocity measurement
Velocity parameter . .
. . . . . . . . . . . . . . . .77
. . . . . . . . . . . . . . . .88
. . . . . . . . . 78, 80, 82
. . . . . . . . . . . . . . . .78
W
Warning label and certification label . . . . . . .7
Working range . . . . . . . . . . . . . . . . . . . . .21
104
BPS 34
Leuze electronic
Leuze electronic
Leuze electronic GmbH + Co. KG
P.O. Box 11 11, D- 73277 Owen / Teck
Tel. +49(0)7021/ 573-0,
Fax +49(0)7021/ 573-199
E-mail: [email protected]e, www.leuze.de
Sales and Service
Sales Region East
Phone 035027/629-106
Fax 035027/629-107
Sales Region North
Phone 07021/573-306
Fax 07021/9850950
Postal code areas
20000-38999
40000-53999
56000-65999
97000-97999
Hamburg
Berlin
Hannover
Postal code areas
01000-19999
39000-39999
98000-99999
Düsseldorf
Dresden
Frankfurt
Nürnberg
Stuttgart
Owen/Teck
München
Sales Region South
Phone 07021/573-307
Fax 07021/9850911
Postal code areas
54000-55999
66000-96999
Worldwide
JP (Japan)
C. Illies & Co., Ltd.
Tel. Int. + 81 (0) 3 /34434111
Fax Int. + 81 (0) 3 /34434118
AT (Austria)
Ing. Franz Schmachtl KG
Tel. Int. + 43 (0) 732/7646 -0
Fax Int. + 43 (0) 732/785036
FI (Finland)
SKS-automaatio Oy
Tel. Int. + 358 (0) 9/85 26 61
Fax Int. + 358 (0) 9/852 68 20
KR (South Korea)
Leuze electronic Co., Ltd.
Tel. Int. + 82 (0) 31/382 82 28
Fax Int. + 82 (0) 31/382 85 22
AU + NZ (Australia + New Zealand)
Balluff-Leuze Pty. Ltd.
Tel. Int. + 61 (0) 3 /9764 23 66
Fax Int. + 61 (0) 3 /9753 32 62
FR (France)
Leuze electronic sarl.
Tel. Int. + 33 (0) 1/60051220
Fax Int. + 33 (0) 1/60050365
MX (Mexico)
Leuze Lumiflex México, S.A. de C.V.
Tel. Int. + 52 (0) 81/83 71 86 16
Fax Int. + 52 (0) 81/83 71 85 88
BE (Belgium)
Leuze electronic nv /sa
Tel. Int. + 32 (0) 2/2531600
Fax Int. + 32 (0) 2/2531536
GB (United Kingdom)
Leuze Mayser electronic Ltd.
Tel. Int. + 44 (0) 1480/408500
Fax Int. + 44 (0) 1480/403808
MY (Malaysia)
Ingermark (M) SDN.BHD
Tel. Int. + 60 (0) 3 /60 34 27 88
Fax Int. + 60 (0) 3 /60 34 21 88
BR (Brasil)
Leuze electronic Ltda.
Tel. Int. + 55 (0) 11/ 4195 -6134
Fax Int. + 55 (0) 11/ 4195 -6177
GR (Greece)
UTECO A.B.E.E.
Tel. Int. + 30 (0) 210/ 4 2100 50
Fax Int. + 30 (0) 210/ 4 2120 33
NL (Netherlands)
Leuze electronic B.V.
Tel. Int. + 31 (0) 418 /65 35 44
Fax Int. + 31 (0) 418 /6538 08
CH (Switzerland)
Leuze electronic AG
Tel. Int. + 41 (0) 1/8340204
Fax Int. + 41 (0) 1/8332626
HK (Hong Kong)
Sensortech Company
Tel. Int. + 852/26 51 01 88
Fax Int. + 852/26 51 03 88
NO (Norway)
Elteco AS
Tel. Int. + 47 (0) 35 /562070
Fax Int. + 47 (0) 35 /562099
CL (Chile)
Imp. Tec. Vignola S.A.I.C.
Tel. Int. + 56 (0) 32/351111
Fax Int. + 56 (0) 32/351128
HU (Hungary)
Kvalix Automatika Kft.
Tel. Int. + 36 (0) 1/2 7222 42
Fax Int. + 36 (0) 1/2 72 2244
PL (Poland)
Balluff Sp. z. o. o.
Tel. Int. + 48 (0) 22/833 15 64
Fax Int. + 48 (0) 22/833 09 69
CN (China)
Leuze electronic GmbH + Co. KG
Shanghai Representative Office
Tel. Int. + 86(0)21/ 6888 0920
Fax Int. + 86(0)21/ 6888 0919
IL (Israel)
Galoz electronics Ltd.
Tel. Int. + 972 (0) 3/9023456
Fax Int. + 972 (0) 3/9021990
PT (Portugal)
LA2P, Lda.
Tel. Int. + 351 (0) 21/444 70 70
Fax Int. + 351 (0) 21/4 44 70 75
IN (India)
Global Tech (India) Pvt. Ltd.
Tel. Int. + 91 (0) 20 /24 4700 85
Fax Int. + 91 (0) 20 /24 47 0086
RO (Romania)
O`Boyle s.r.l.
Tel. Int. + 40 (0) 56 /20 13 46
Fax Int. + 40 (0) 56 /2210 36
IR (Iran)
Tavan Ressan Co. Ltd.
Tel. Int. + 98 (0) 21/2606766
Fax Int. + 98 (0) 21/2002883
RU (Russian Federation)
All Impex
Tel. + Fax +7 095/ 9332097
CO (Colombia)
Componentes Electronicas Ltda.
Tel. Int. + 57 (0) 4/35110 49
Fax Int. + 57 (0) 4/3511019
CZ (Czech Republic)
Schmachtl CZ s.r.o.
Tel. Int. + 420 (0) 2 /44 00 1500
Fax Int. + 420 (0) 2 /44 91 0700
DK (Denmark)
Desim Elektronik APS
Tel. Int. + 45/ 70220066
Fax Int. + 45/ 70222220
IT (Italy)
Leuze electronic S.r.l.
Tel. Int. + 39 02 /2611 0643
Fax Int. + 39 02 /261106 40
SE (Sweden)
Leuze SensorGruppen AB
Tel. + 46 (0) 8 /731 51 90
Fax + 46 (0) 8 /731 51 05
SG + PH + ID (Singapore +
Philippines + Indonesia)
Balluff Asia Pte. Ltd.
Tel. Int. + 65 / 62 5243 84
Fax Int. + 65 / 62 5290 60
SI (Slovenia)
Tipteh d.o.o.
Tel. Int. + 386 (0) 1/ 200 5150
Fax Int. + 386 (0) 1/ 200 5151
SK (Slovakia)
Schmachtl SK s.r.o.
Tel. Int. + 421 (0) 2/ 58 27 56 00
Fax Int. + 421 (0) 2/ 58 27 56 01
TH (Thailand)
Industrial Electrical Co. Ltd.
Tel. Int. + 66 (0) 2/6 42- 67 00
Fax Int. + 66 (0) 2/6 42-42 49
TR (Turkey)
Balluff Sensör Ltd. Sti.
Tel. Int. + 90 (0) 212/320 04 11
Fax Int. + 90 (0) 212/320 0416
TW (Taiwan)
Great Cofue Technology Co., Ltd.
Tel. Int. + 886 (0) 2/29 83 80 77
Fax Int. + 886 (0) 2/29 85 33 73
UA (Ukraine)
Beverly-Foods Ltd.
Tel. Int. + 38 044/525 59 27
Fax Int. + 38 044/525 78 07
US + CA (United States +
Canada)
Leuze Lumiflex Inc.
Tel. Int. + 1 (0) 248/ 4864466
Fax Int. + 1 (0) 248/ 486 66 99
ZA (South Africa)
Countapulse Controls (PTY.) Ltd.
Tel. Int. + 27 (0) 11/6157556
Fax Int. + 27 (0) 11/6157513
Part. No. 501 05 437
ES (Spain)
Leuze electronic S.A.
Tel. Int. + 34 93/4 09 79 00
Fax Int. + 34 93/490 58 20
GB 167/03 – 01/06
AR (Argentina)
Nortécnica S. R. L.
Tel. Int. + 54 (0) 11 /4757 -31 29
Fax Int. + 54 (0) 11 /4757 -1088
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement