User manual | Mounting

l i nda b | we si mpl i f y c onstr u ction
LindabPlexus
Supply air beam
Installation instructions
lin dab | w e s i m p l i fy c o n s t r u c t i o n
Plexus
1 Content and symbols
1.1 Content
1. Content and symbols....................................... 2
1.1 Content..................................................................... 2
1.2 Symbols................................................................... 3
2. Control of delivery........................................... 3
2.1 Before you start........................................................ 3
2.2 Safe operation.......................................................... 3
2.3 Receipt of goods..................................................... 3
2.4 Unloading of goods................................................. 3
2.5 Handling / Carrying.................................................. 3
2.6 Tools......................................................................... 4
2.7 Installation................................................................ 4
2.8 Where to find additional instructions or technical
documentation......................................................... 4
2.9 Cleaning after assembly/before commissioning..... 4
2.10 Packing, unpacking guideline................................ 5
2.11 Product labelling..................................................... 6
2.12 Order code............................................................. 7
2.13 Order code examples............................................. 7
2.14 Label....................................................................... 7
2.15 Contents of order................................................... 8
2.16 Plus features........................................................... 8
2.16.1 Inlet faceplates..................................................... 8
2.16.2 Outlet front grilles...................................................... 8
2.16.3 Integrated valves................................................. 8
2.16.4 Integrated Actuators............................................ 8
2.16.5 Integrated Regula components.......................... 8
2.17 Accessories............................................................ 8
3. Product specification....................................... 9
3.1 Product description................................................. 9
3.2 Dimensions.............................................................. 9
3.3 Plexus....................................................................... 9
3.4 Material data.......................................................... 10
3.5 Environmental Declarations................................... 10
3.6 Working and test pressure.................................... 10
3.7 Water quality.......................................................... 10
3.8 Air quality............................................................... 10
3.9 Capacity test.......................................................... 10
4 Connections.....................................................11
4.1 Water connections................................................. 11
4.1.1 Before installation................................................ 11
4.1.2 Push on fitting..................................................... 12
4.1.3 Compression fitting............................................. 12
4.1.4 Flexible hoses...................................................... 12
4.1.5 Additional Lindab accessories for water
connections......................................................... 13
4.1.6 Possible connections water cooling
(2-pipe, Standard).................................................. 14
4.1.7 Possible connections water cooling and
heating (4-pipe, Plus feature) ................................. 14
4.2. Air connections..................................................... 16
4.2.1 Air connection installation................................... 16
2
4.2.2 Possible connections supply air......................... 16
4.2.3 Possible connections exhaust air....................... 16
4.3 Possible combination of connections................... 16
4.4 Electrical connections........................................... 17
4.4.1 Regula components on the beam....................... 17
4.4.2 Example 1: Wiring scheme with Regula
Connect multi...................................................... 18
4.4.3 Example 2: Wiring scheme with Regula
Connect basic..................................................... 18
4.4.4 Regula Connect on the beam............................. 19
4.4.5 Regula Secura on the beam............................... 19
4.4.6 Valves and Actuators on the beam..................... 19
4.4.7 Regula Combi on/with the beam........................ 19
4.4.8 Actuators............................................................. 19
5 Installation of product..................................... 20
5.1 Handling of product............................................... 20
5.2 Ceiling systems...................................................... 20
5.3 General installation principles............................... 21
5.3.1 Recessed in suspended T-bar ceiling................ 21
5.3.2 Exposed, sealed to the ceiling........................... 21
5.3.3 Exposed, free hanging........................................ 21
5.3.4 Free hanging above perforated or eggcrate
ceiling.................................................................. 21
5.3.5 Recessed in suspended (permanent)
ceiling.................................................................. 21
5.3.6 Recessed in suspended (permanent) ceiling
without cover flanges.......................................... 21
5.4 Preparation for installation on the product............ 22
5.5 Preparation for installations of the product........... 23
5.5.1 Basics steps of installing the product................ 24
6 Adjustment and commissioning...................... 28
6.1 Airflow and pressure.............................................. 28
6.1.1 Jet cone 2 adjustment pins................................. 28
6.1.2 Finding values for JetCone pins ......................... 29
6.1.3 Adjusting air flow and pressure with JetCone
pins....................................................................... 29
6.2 Adjustment of air distribution profile..................... 30
6.3 Measuring air pressure and calculating the air
flow......................................................................... 30
6.3.1 Measuring static nozzle pressure and air
pressure.............................................................. 30
6.3.2 Calculating the actual air flow............................ 30
6.3.3 Changing the actual air flow............................... 30
6.3.4 Changing the air distribution profile................... 30
6.3.5 Plexus pressure / airflow diagrams.................... 31
6.4 Water flow rate....................................................... 32
6.4.1 Pre-setting of valves........................................... 32
6.4.2 Balancing strategy.............................................. 32
7. Maintenance................................................... 33
7.1 Remove the outlet front grille................................. 33
7.2 Open inlet faceplate............................................... 33
7.3 Opening inspection hatch...................................... 33
7.4 Lower battery......................................................... 34
8 Accessories..................................................... 35
We reserve the right to make changes without prior notice
03-04-2017
l i nda b | we si mpl i f y c onst ru ction
Plexus
1.2 Symbols
Hot water
Cold water
2.4 Unloading of goods
10-25
kg !
Heavy Load - 2 man job It is recommended to use
a “lift” for mounting.
Hand-pull
The beams and panels are normally delivered packed on
wooden pallets. Lift the pallets carefully with a fork lift and
place them on a dry and plain surface/ground. If the beams
are delivered in single boxes, wooden blocks should be
placed on the ground at one-metre intervals (or a pallet),
before the boxes are been placed to store. Lindabs water
products must be stored on a plane surface in a dry and
well ventilated place, preferably indoors. If they have to
be stored outdoors, protect them with a waterproof cover
and store them protected from rain beneath a roof or other
until they are fitted.
2.5 Handling / Carrying
2 Control of delivery
2.1 Before you start
The beam or panel must be handled with care, ensuring that
it will not be scratched or bended during transportation,
preparation and installation.
Read through the entire installation instruction before
commencing installation in order to determine which parts
that needs to be performed and in what order to be done.
Always carry the beams or panels piecewise into the
building. Keep the product in the package as long as you
can.
Lindab is a supplier of complete water products, but we
offer also a wide range of accessories which suit perfectly
to our water products simplifying your installation work,
e.g. different type of hangers, Tektite-couplings, closing
valves, thermostatic valves and actuators, flexible hoses,
customized regulation components, customized cabeling
and more. See also the separate document “Accessories”.
Lindab will also provide you with a full ventilation system,
with a wide range of Lindab Safe components. See also
“Air Duct Systems”.
10-25
2.2 Safe operation
kg !
Beware of sharp edges, especially of the coils. Always
wear thin gloves and protective clothing.
All existing safety regulations must be observed when
working with Lindab water products. Check the weights
of the beams or the panels with the installation instruction
before carrying.
2.3 Receipt of goods
Start by checking that the delivery is complete according
to the order and that everything listed on the consignment
note has been delivered. Then carry out a review of the
products and make sure that nothing was damaged during
transportation. If you discover damage that has occurred
during delivery, it must be notified immediately.
Lindab is not responsible for costs associated with the
replacement of products that have been installed in any
way other than shown in these installation instructions.
Never use piping connections or edges to lift them, neither
when you unpack them nor when you carry them towards
the construction site.
Do not place the product directly on the floor. Use the
protective corners from package or other clean means
from package to place the product before installation.
Be careful if you must carry a long panel horizontally; if
the panels are bended lengthwise, the profiles may be
deformed and the piping could be loosen from the panel.
When opening the box with a knife, be careful not to
damage the product.
Each beam is equipped with protective film to avoid any
damage during transportation and handling on building
site. The film needs to be removed before commissioning
the products.
We reserve the right to make changes without prior notice
03-04-2017
3
lin dab | w e s i m p l i fy c o n s t r u c t i o n
Plexus
2.6 Tools
To install the beam, panel or facade unit, the following tools are required.
Knife
Gloves
Tape measure
Pencil
Spanner
Drill machine
Percussion drill
Crowbar
Tectite tool 12mm
(Order no: 884087)
Tectite tool small 12mm
(Order no: 646881)
Screwdriver
Spirit level
Lindab PC410
(Order no: 103344)
Deburring tool
Bits and drills
Vacum cleaner
Dust-cleaner
2.7 Installation
It is important to use the correct hangers and the
recommended amount for all installation principles.
Different possible installation principles are shown in the
installation instruction and hangers from Lindab should be
used to ensure, that they are intended for the purpose and
are safe to use.
Lindab´s water products can be ordered, to be adapted
to a wide range of different ceiling systems, please check
installation instruction to ensure best adaptation.
The Lindab water products should always be installed
separately hanged up from the recessed ceiling. The weight
of the product should not be covered by the ceiling system.
Use plastic folio or other to protect the product during on
site construction continually to keep the products in best
condition and avoid any scratches.
4
Shoes with soft soles
2.8 Where to find additional instructions or
technical documentation
In the following chapters we will refer to additional technical
documents or/and instructions by a certain keyword written
as a link.
If so you will easily find it with our Lindab Quick Selection
Tool: www.lindqst.com
1. Visit www.lindqst.com
2. Select “documentation finder”
3. Select keyword (product name)
4. Follow the link
5. Find your document under “Related documents”
2.9 Cleaning after assembly/ before
commissioning
Please remember to remove plastic folio and other
protection material before commissioning and clean the
product before hand over.
We reserve the right to make changes without prior notice
03-04-2017
l i nda b | we si mpl i f y c onst ru ction
Plexus
2.10 Packing, unpacking guideline
10-25
kg !
We reserve the right to make changes without prior notice
03-04-2017
5
lin dab | w e s i m p l i fy c o n s t r u c t i o n
Plexus
2.11 Product labelling
Order : xx-xxxxx
Pos : xx
xx
Plexus
x-x-xx-xx-xxx-Xx
Munio-I-xxx-12-125-AX
Pressure:
xx Pa
AA
x,xx m
Flow:
Project : xxxxxx
xxxxxxxx
xxxx-xxxx-xxxx
xx-xx
Mark :
xxxxx
xx Plugs : N/A
xx
Nozzles : N/A
xx-xx
Product ID :
xxxxxxx
xx l/s
BB
Sign. : xx
ΔpStat [Pa]
JetCones
Plexus S60
0
120
1
2
3
Position of JetCone adjustment pins
4
5
6
7
8
9
100
1
3
Date
Pstat [Pa]
qa [l/s]
1
2
3
4
Signature
Pos.
0-9
2
80
70
60
50
40
30
4
4
5
6
20
Rev. 04-2012
7
8
9
30
10
15
40
Plexus_label.indd 1
6
50
20
60
70
25
80
30
100
35
40
150
qa [l/s]
qa [m3/h]
09-02-2016 14:15:56
We reserve the right to make changes without prior notice
03-04-2017
l i nda b | we si mpl i f y c onst ru ction
Plexus
2.12 Order code
Order : xx-xxxxx
Pos : xx
xx
Plexus
x-x-xx-xx-xxx-Xx
Munio-I-xxx-12-125-AX
Plexus I, (X, U, Y, Z)
Pressure:
xx Pa
AA
x,xx m
Flow:
Project : xxxxxx
xxxxxxxx
xxxx-xxxx-xxxx
xx-xx
Mark :
xxxxx
xx Plugs : N/A
xx
Nozzles : N/A
Product ID : xx-xx
xxxxxxx
Plexus
X
I
X
Y
Z
X
S*
L*
M*
H*
SA***
F
Plexus
F
X
XXX
12
60
62
67
120*
122*
Sign. : xx
XXX
Ø12
(2 x 2 )
x2
60
120*
x2
XXX
12
Plexus F
xx l/s
BB
Ø125**
Ø160**
( x1 )
XX
XX
XX
Preset static pressure
before nozzles [Pa]
Preset airflow [l/s]
XX
XX
A5
A6
B5
B6
A1
B1
XXX
XX
* 120 and 122 only available when S-configuration has been selected. L, M, H configurations only available in 60, 62, 67 versions.
**ØH (Side air connection (A)) = 125 only.
**ØV (Top air connection (B)) = 125 only for S-configuration. ØV = 160 only for L,M,H configurations. (See also dimension table 3.2).
***The type SA (integrated steel frame) is available for version ISA-60 and 120 only (for T24/T15 lay-in 600 (ceiling type 1)
2.13 Order code examples
Order : xx-xxxxx
Pos :
xx
Plexus I-S-60-12-125-A5
Munio-I-xxx-12-125-AX
Pressure:
AA
Pa
60 Pa
x,xx m
Flow:
Project : xxxxxx xxxxxxxx
Mark :
xxxxx
xx
N/A
Nozzles : N/A
Plugs : N/A
Product ID :
xxxxxxx
Order : xx-xxxxx
Pos :
xx
Plexus I-S-60-12-125-B6
Munio-I-xxx-12-125-AX
Pressure:
AA
Pa
60 Pa
x,xx m
Flow:
Project : xxxxxx xxxxxxxx
Mark :
xxxxx
xx
N/A
Nozzles : N/A
Plugs : N/A
Product ID :
xxxxxxx
Order : xx-xxxxx
Pos :
xx
Plexus F-S-60-12-125-A1
Munio-I-xxx-12-125-AX
Pressure:
AA
Pa
60 Pa
BB
24
l/sl/s
Sign. :
BB
24
l/sl/s
Sign. :
x,xx m
Flow:
Project : xxxxxx xxxxxxxx
Mark :
xxxxx
xx
N/A
Nozzles : N/A
Plugs : N/A
Product ID :
xxxxxxx
BB
24
l/sl/s
Sign. :
Plexus I - S - 60 - 12 - 125 - A5 - 60 Pa - 24 l/s
Plexus I - S - 60 - 12 - 125 - B6 - 60 Pa - 24 l/s
Plexus F - S - 60 - 12 - 125 - A1 - 60 Pa - 24 l/s
2.14 Label
Order : xx-xxxxx
Pos : xx
xx
Plexus
x-x-xx-xx-xxx-Xx
Munio-I-xxx-12-125-AX
On the label you will find:
•
•
•
•
•
•
•
Order: Order identification number.
Pos: Order position.
Product: Product configuration.
Project: Project name.
Mark: Marking noted on order.
Product ID: Product number.
Sign: To be signed when checked and commissioned on site.
Pressure:
xx Pa
AA
x,xx m
Flow:
Project : xxxxxx
xxxxxxxx
xxxx-xxxx-xxxx
xx-xx
Mark :
xxxxx
xx Plugs : N/A
xx
Nozzles : N/A
Product ID : xx-xx
xxxxxxx
We reserve the right to make changes without prior notice
03-04-2017
xx l/s
BB
Sign. : xx
7
lin dab | w e s i m p l i fy c o n s t r u c t i o n
Plexus
2.15 Contents of order
2.17 Accessories
Standard package/order contains:
Here you see some general accessories. For full range
see separate Accessories document.
•
•
•
•
Beam
Plus features (pre-installed in factory)
4 pc/beam of copper insets (separate in smaller box)
Accessories (separate in smaller box)
Go to Accessories for details.
Threaded rod kit
M6/M8
2.16 Plus features
x4
2.16.1 Inlet faceplates
Order no: see Accessories
Not relevant for Plexus
2.16.2 Outlet front grilles
Not relevant for Plexus
Flexible hoses
2.16.3 Integrated valves
Order no: 680080 (0,4m push on, 12 and 12mm).
See Accessories
Transformer
Go to TTR/TTV water valves for details.
2.16.4 Integrated Actuators
Order no: see Accessories
Tectite fittings
Go to Actuators for details.
Order no: 647690, 884050 and 884014 (12mm)
see Accessories
2.16.5 Integrated Regula components
Regula Combi
Condensation sensor and Regula Secura
LINDAB
Heating link - S
Cooling link - S
Supply link - N
Supply link - L
Supply in - N
Supply in 24V - L
Heating link - S
Cooling link - S
Supply link - N
Supply link - L
Heating in - S
Cooling in - S
Supply out - N
Supply out - L
Cooling out - S
Cooling out - N
Cooling out - L
Heating out - S
Heating out - N
Heating out - L
Presence in - S
Presence in - S
Presence out - N
Presence out - L
Damper out - S
Damper out - N
Damper out - L
RC in/out
CO2 in - S
CO2 in - S
CO2 out - N
CO2 out - L
N = Neutral
L = Load
S = Signal
Rc LINK
Rc LINK
Multi
REGULA CONNECT
Regula Multi connect card
Go to Regula for details.
8
We reserve the right to make changes without prior notice
03-04-2017
l i nda b | we si mpl i f y c onst ru ction
Plexus
3 Product specification
3.1 Product description
The Plexus beam is a 360° comfort unit and is standardly prepared for ventilation and cooling (2-Pipe connection).
It is available in an integrateable (I 60 / I 120) and an exposed version (F 60 / F 120).
3.2 Dimensions
Plexus I, ( X, U, Y, Z )
Plexus F
B
mm
ØH
mm
ØV
mm
I ( S/SA, L, M, H) 60
594
594
125
125/160
1, 2, 3, 8
X ( S, L, M, H) 60
599
599
125
125/160
4, 5, 6, 7, 14
U ( S, L, M, H) 60
599
599
125
125/160
USA 2’ x 2’
Y ( S, L, M, H) 60
575
575
125
B
125/160
9, 11
Z ( S, L, M, H) 60
584
584
125
125/160
B
10
I ( S, L, M, H) 62
619
619
125
I ( S/SA, L, M, H) 67
669
669
125
I S 120
594
1194
125
599
1199
B/2
21
125/160
31, 32
F ( S, L, M, H) 60
669
669
125
125/160
F S 120
669
1269
125
160
!
1, 2, 3, 8
Plexus (F) - (S)
=> Øv = 125
4, 5, 6, 7, 14
70
17.5
Y S 120
575
1174
125
160
Z S 120
584
1183
125
B/2
160
U S 120
599
1209
125
160
USA 2' x 2'
I S 122
619
1244
125
160
21
!
ØV
mm
76.2
Øv
125/160
160
ØH
mm
A
Øv
Plexus (F) - (L, M, H)
=> Øv = 160
A
Øv
ØH
225
76.2
40
40
125
B
mm
9, 11
ØH
225
X S 120
Øv
160
A
mm
Ceiling type
70
17.5
10
333
79
333
79
Plexus (I, X, U,Y, Z) - (L, M, H)
=> Øv = 160
Plexus (I, X, Y, Z) - (S)
=> Øv = 125
128
128
1111
4040
B
476
476
Øv
Øv
220
220
ØHØH
B
225
225
A
mm
4949
40
40
A
A
3.3 Plexus
BB
480 (Plexus
(Plexus120
120= =1080)
1080)
480
365
365
We reserve the right to make changes without prior notice
03-04-2017
9
lin dab | w e s i m p l i fy c o n s t r u c t i o n
Plexus
3.4 Material data
Type
Plexus I 60
Plexus I 120
Plexus F 60
Plexus F 120
Cooling/Heating
Cooling/Heating
Cooling/Heating
Cooling/Heating
Weight, kg
11.6
Water content, cooling, l
1.0
1.3
1.0
1.3
Water content, heating, l
0.2
0.4
0.2
0.4
Water content, cooling only, l
1.2
1.3
1.2
1.3
EN 12735-2
CU-DHP
EN 12735-2
CU-DHP
EN 12735-2
CU-DHP
EN 12735-2
CU-DHP
Copper pipes, quality
18.6
20
17.2
28.9
30.3
3.5 Environmental Declarations
3.7 Water quality
Please visit www.lindqst.com
Lindab recommend water treatment and quality to be
according to VDI 2035-2.
• Select Documentation Finder
• The water preparation and maintenance for the chilled
beam water circuit must be handled by a specialist.
• Select “Plexus”
• Select “Related Documents” Building product
declaration or Declaration of conformity.
• To prevent corrosion, the water circuit must be
airtight.
3.6 Working and test pressure
Lindab’s waterborne products have been manufactured
and tested according to Pressure Equipment Directive
97/237EC. The products are classified as SEP - Sound
Engineering Practice.
• The water system must also be equipped with
aerators to remove any build-up air in the system.
• The water must be oxygen free, to prevent corrosion.
• The water system must be filled with potable water
that complies with the “EC directive 98/83/EC”.
• pH value of water must be between approximately 6-9
pH.
Pressure table
Pressure class
PN10
Max. working pressure
10 bar
Max. recommended dynamic pressure
0.2 bar
Max. test pressure
16 bar
• The water velocities should not exceed 1m/s, and
should be kept as close to the nominal flow as
possible to minimize noise and optimize the energy
yield.
• Use in-line strainers to remove dirt particles from the
water.
• If the water contains any additive inhibitor, then it must
be appropriate to use with copper and solder.
3.8 Air quality
Primary supply air have to be clean, dry and filtered
before reaching the beam.
3.9 Capacity test
Lindabs active chilled beams are Eurovent-certified and
tested according to EN-15116.
Please visit Plexus on www.lindqst.com and see
Eurovent for more details.
10
We reserve the right to make changes without prior notice
03-04-2017
l i nda b | we si mpl i f y c onst ru ction
Plexus
4 Connections
4.1. Water connections
Flow indication arrows are shown on the inlet and return pipes in order to assist the installer.
If the beam has been ordered with integrated valves, a special direction of the flow must be upheld to ensure correct flow
through the thermostatic valve. Please note the flow direction indicator on the valve to insure correct installation in relation to
the desired flow.
When connecting a panel or a beam with the piping system either a push-on fitting or a compression coupling should be
used. Lindab have tested and recommends push-on fittings from Tectite (which are available as accessory. See Accessories.
To avoid sound being transported over the beam, we recommend to use flexible hoses between the piping and the beam
connections.
4.1.1 Before installation
• Notice! The connection pipes are internally soft-welded, therefore it’s not allowed to solder the beam to the pipes. For
other than Lindab fittings and valves, please consult the installation guide for the specific fitting for further details on
proper installation.
• Both inlet- and return pipes are covered by a plastic or rubber protection cover, which must be removed before installation.
• After removing the protection cover, make sure that the pipe is intact and undamaged, especially at the pipe end, as even
small dents and scratches potentially pose a risk of leakage in the system.
• Eventually deburr the pipe ends on the inside and the outside, using a deburring tool before installation.
• Always remember to do a pressure test after assembly the pipe work.
We reserve the right to make changes without prior notice
03-04-2017
11
lin dab | w e s i m p l i fy c o n s t r u c t i o n
Plexus
4.1.2 Push-on fitting
• Mount a push-on fitting to the pipe. Make sure to press the fitting all the way onto the pipe.
Picture 8.b
Push-on fitting on
Picture 8.a
Push-on fitting of
• Mount a push-on valve to the pipe. Make sure the valve has the correct flow direction (see indication arrow on the valve)
and that you have the correct valve, when integrated valve has been chosen (see indication on valve or follow cabelling
to Regula Connect card).
4.1.3 Compression fitting
• While mounting a compression fitting, the pipe will be exposed to a big amount of force, creating a risk of crushing
the pipe. To ensure that the pipe will not be crushed when mounting the compression fitting, a copper insert must be
inserted into the pipe (always part of the delivery).
• The copper insert should be placed inside the pipe on the beam. Always support the copper pipe coil when inserting the
copper insert into position.
• Mount a compression coupling and/or a valve to the pipe. Don’t stress the nut too much, since this may crush the pipe.
• Please refer to the suppliers manual.
4.1.4 Flexible hoses
• Our flexible hoses can be used with both push-on and compression fitting. We recommend to use Tectite fittings, for
easier and faster mounting.
12
We reserve the right to make changes without prior notice
03-04-2017
l i nda b | we si mpl i f y c onst ru ction
Plexus
4.1.5 Additional Lindab accessories for water
connections
Valves and fittings
Lindab TTR and TTV water valves
The Lindab TTR and TTV valves must be used with all
standard application chilled beams, radiant panels and
facade units. The TTR and TTV valves ensures easy and
fast installation thanks to the simple yet effective Tectite
push-on connections.
For further information,
please see TTR/
TTV water valves
documentation.
Valves and Actuators installation
When actuator and valves are ordered together with
the Plexus and other Regula components, the cables
are pre-connected to the Connect card / Secura
from factory - (depending on your chosen solution).
The actuator and valve is taped to the side of the Plexus
and has to be connected to the correct water-pipe, turning
the right way.
Example
Push on valve with Actuator installed on the battery’s cold
water outlet.
Valve arrow indicator must point in same direction as arrow
on beam pipe label.
Ballorex Dynamic
For application in systems where pressure alterations may
occur, the Ballorex Dynamic ensures an easy and precise
dynamic flow regulation.
Further information on request.
Push on valve with air vent (aerator)
If a waterborne unit is mounted in a location where
issues with build up air may
occur, applying an aerator is
recommendable. As our aerators
comes complete with Tectite
fittings, installation is done in mere
seconds.
Order no: 647690 (12mm)
Ballofix valves
For easy closing off water connection pipes (available with
or without handle).
Order no: 642663 / 642662
(without handle, 12mm)
For more details see: Accessories
Actuators
The actuator is a thermoelectric
actuator for opening and closing
valves on heating circuit distributors
of concealed floor heating and
cooling systems. Features, as
protection in case of leaky valves,
compact and modern casing,
versions in normally closed and
normally open, valve adapter
concept and an enhanced life time
makes the actuator competitive and flexible. The actuator
is controlled by a room thermostat with two-point output
or pulse-width modulation.
See Actuators
We reserve the right to make changes without prior notice
03-04-2017
13
lin dab | w e s i m p l i fy c o n s t r u c t i o n
Plexus
4.1.6 Possible connections water cooling
(2-pipe, Standard)
4.1.7 Possible connections water cooling and
heating (4-pipe, Plus feature)
All the Plexus active chilled beams are in the standard
version equipped with a so called “2-pipe connection”
and contain one water circuit (cooling).
All Plexus’ can have a 4-pipe water connection (plus
feature), which beside the cooling circuit also includes a
heating circuit.
The dimension for all water pipe connections are 12 mm.
The dimension for all water pipe connections are 12 mm.
Plexus 60 I, (X, U, Y, Z). Cooling. (Standard).
Plexus 60. I, (X, U, Y, Z). Cooling and heating.
6
6
5
5
44
44
79
327
238
105
35
35
70
70
17.5
70
17.5
79
327
238
Plexus 120. I, (X, U, Y, Z). Cooling. (Standard).
Plexus 120. I, (X, U, Y, Z). Cooling and heating.
327
238
327
238
385
192.5
35
385
192.5
87.5
70
70
105
Plexus I, (X, U, Y, Z). 60/120, cooling and heating. In /outs
60
14
120
We reserve the right to make changes without prior notice
03-04-2017
l i nda b | we si mpl i f y c onst ru ction
Plexus
Plexus F 60/120. Cooling. (Standard)
Plexus F 60/120. Cooling and heating.
1
1
44
44
79
79
225
ØH
70
70
334,5 (Plexus F120 = 634,5)
We reserve the right to make changes without prior notice
03-04-2017
17.5
333
55
79
B
17.5
B
334,5 (Plexus F120 = 634,5)
225
A
Øv
15
lin dab | w e s i m p l i fy c o n s t r u c t i o n
Plexus
4.2 Air connections
4.3 Possible combination of connections
4.2.1 Air connection installation
The primary air supply must be connected with instructions
from a ventilation specialist. Lindab’s chilled beams can
beneficially be used together with Lindab’s Safe® duct
systems.
We recommend a flexible duct connection, like Lindab
DRATMFU-125, to balance out different installation heights
or directions between connection and duct and avoid
sound will be diverted from piping system to the ceiling.
B
6
A
5
I, (X, U, Y, Z) 60 / 120
4.2.2 Possible connections supply air
B
B
A
A
1
I, (X, U, Y, Z) 60 / 120
F 60 / 120
B
A
F 60 / 120
4.2.3 Possible connections exhaust air
Not relevant for Plexus
16
We reserve the right to make changes without prior notice
03-04-2017
l i nda b | we si mpl i f y c onst ru ction
Plexus
4.4 Electrical connections
Electrical connections on the beam are only necessary, when plus features are chosen and thanks to the pre-fabrication it is as
easy as “plug and play”. The components are always installed near the water-connection at the end of the beam.
For further information, see Regula .
4.4.1 Regula components on the beam
5
1
Regula Secura Sensor
Regula Convert
Power
Regula Convert
Regula Sensor Philips
Regula Secura
2
3
Regula Connect Cards
Multi
Pascal
Basic
REGULA CONNECT
REGULA CONNECT
REGULA CONNECT
Multi
Rc LINK
N = Neutral
L = Load
S = Signal
Pascal
Rc LINK
N = Neutral
L = Load
S = Signal
Rc LINK
Rc LINK
RC in/out
RC in / out
CO2 in - S
CO2 in - S
CO2 out - N
CO2 out - L
CO2 in - S1
CO2 in - S2
CO2 out - N
CO2 out - L
Presence in - S
Presence in - S
Presence out - N
Presence out - L
Presence in - S1
Presence in - S2
Presence out - N
Presence out - L
Damper out - S
Damper out - N
Damper out - L
Damper in - Pos
Damper out - S
Damper out - N
Damper out - L
Heating out - S
Heating out - N
Heating out - L
Cooling out - S
Cooling out - N
Cooling out - L
Heating in - S
Cooling in - S
Supply out - N
Supply out - L
Heating link - S
Cooling link - S
Supply link - N
Heating 0-10V- S
Heating 0-10V- N
Heating 0-10V- L
4
Regula Combi
Presence sensor
Basic
N = Neutral
L = Load
S = Signal
Heating out - S
Heating out - N
Heating out - L
Cooling out - S
Cooling out - N
Cooling out - L
Heating in - S
Cooling in - S
Supply out - N
Supply out - L
Heating link_S
Cooling link_S
Supply link - N
Supply link - L
Heating link_S
Cooling link_S
Supply link - N
Supply link - L
Supply in - N
Supply in - 24V - L
LINDAB
Supply Link2 - N
Supply Link2 - L
Supply Link1 - N
Supply Link1 - L
Supply in - N
Supply in-24V - L
LINDAB
Supply link - L
Heating link - S
Cooling link - S
Supply link - N
Supply link - L
Supply in - N
Supply in 24V - L
LINDAB
(with protection covers, optional).
We reserve the right to make changes without prior notice
03-04-2017
17
lin dab | w e s i m p l i fy c o n s t r u c t i o n
Plexus
4.4.2 Example 1: Wiring scheme with
Regula Connect multi
Regula Combi
Please visit www.lindqst.com and check out the
“Wiring scheme configurator” for your set-up.
REGULA CONNECT
T568B
T
21
22
40
32
31
41
ends must
be insulated
Regula Presence
Power
{
White/Orange
Orange
White/Green
Blue
White/Blue
Green
White/Brown
Brown
1
2
3
4
5
6
7
8
Regula Convert
Multi
Rc LINK
N = Neutral
L = Load
S = Signal
Rc LINK
RC in/out
CO2 in - S
CO2 in - S
CO2 out - N
CO2 out - L
Regula Sensor Philips
Presence
adapter
4 wire RJ11 6P4C, Straight through
Presence in - S
Presence in - S
Presence out - N
Presence out - L
Damper out - S
Damper out - N
Damper out - L
Actuator on/off
24V heating
23
24
11
10
To other Regula Connect Multi
1
2
4.4.3 Example 2: Wiring scheme with
Regula Connect basic
Bro
Blu
24 V
4
5
230 V
Bro
Blu
To other Regula Connect Multi
Transformator
Actuator on/off
24V cooling
Condensation sensor
1
7
2
8
N
L
Blu
Bro
Blu
Bro
Whi
Grn
Bro
Yel
4
3
2
1
4
3
2
1
Blu
Bro
Heating out - S
Heating out - N
Heating out - L
Cooling out - S
Cooling out - N
Cooling out - L
Heating in - S
Cooling in - S
Supply out - N
Supply out - L
Heating link - S
Cooling link - S
Supply link - N
Supply link - L
Heating link - S
Cooling link - S
Supply link - N
Supply link - L
Supply in - N
Supply in 24V - L
LINDAB
Regula Combi
REGULA CONNECT
Basic
N = Neutral
L = Load
S = Signal
Actuator on/off
24V heating
23
24
11
10
To other Regula Connect Basic
Condensation sensor
1
7
2
8
18
1
2
Bro
Blu
We reserve the right to make changes without prior notice
03-04-2017
24 V
4
5
230 V
Bro
Blu
To other Regula Connect Basic
Transformator
Actuator on/off
24V cooling
N
L
Blu
Bro
Blu
Bro
Whi
Grn
Bro
Yel
4
3
2
1
4
3
2
1
Blu
Bro
Heating out - S
Heating out - N
Heating out - L
Cooling out - S
Cooling out - N
Cooling out - L
Heating in - S
Cooling in - S
Supply out - N
Supply out - L
Heating link_S
Cooling link_S
Supply link - N
Supply link - L
Heating link_S
Cooling link_S
Supply link - N
Supply link - L
Supply in - N
Supply in - 24V - L
LINDAB
LINDAB
Supply in - N
Supply in 24V - L
Heating link - S
Cooling link - S
Supply link - N
Supply link - L
Heating link - S
Cooling link - S
Supply link - N
Supply link - L
Heating in - S
Cooling in - S
Supply out - N
Supply out - L
Cooling out - S
Cooling out - N
Cooling out - L
Heating out - S
Heating out - N
Heating out - L
Damper out - S
Damper out - N
Damper out - L
Presence in - S
Presence in - S
Presence out - N
Presence out - L
CO2 in - S
CO2 in - S
CO2 out - N
CO2 out - L
RC in/out
Rc LINK
N = Neutral
L = Load
S = Signal
Rc LINK
Multi
REGULA CONNECT
LINDAB
Supply in - N
Supply in-24V - L
Supply Link2 - N
Supply Link2 - L
Supply Link1 - N
Supply Link1 - L
Heating 0-10V- S
Heating 0-10V- N
Heating 0-10V- L
Damper in - Pos
Damper out - S
Damper out - N
Damper out - L
Presence in - S1
Presence in - S2
Presence out - N
Presence out - L
CO2 in - S1
CO2 in - S2
CO2 out - N
CO2 out - L
RC in / out
Rc LINK
N = Neutral
L = Load
S = Signal
Rc LINK
Pascal
REGULA CONNECT
4.4.4 Regula Connect on the beam
4.4.6 Valves and Actuators on the beam
Connect cards are pre-installed when the beam is ordered
with PLUS-features. See Regula Connect for more details.
Description, see 4.1.5.
Regula Connect Basic
The Regula Combi can be
controlled and programmed
locally in the display, or at a
remote location by a EXOLINE
or MODBUS communication
system. Handles both 24V and
0-10V devices.
LINDAB
Supply in - N
Supply in - 24V - L
Heating link_S
Cooling link_S
Supply link - N
Supply link - L
Heating link_S
Cooling link_S
Supply link - N
Supply link - L
Heating in - S
Cooling in - S
Supply out - N
Supply out - L
Cooling out - S
Cooling out - N
Cooling out - L
Heating out - S
Heating out - N
Heating out - L
N = Neutral
L = Load
S = Signal
Basic
REGULA CONNECT
l i nda b | we si mpl i f y c onst ru ction
Plexus
Regula Connect Pascal
Regula Connect Multi
4.4.7 Regula Combi on/with the beam
See the Regula Combi documentation.
4.4.8 Actuators
Description, see 4.1.5.
4.4.5 Regula Secura on the beam
Regula Secura is pre-installed when the beam is ordered
with PLUS-features. See Regula Secura for more details.
Condensation sensor and Regula Secura
Cable to Regula
Secura
Condensation sensor
We reserve the right to make changes without prior notice
03-04-2017
19
lin dab | w e s i m p l i fy c o n s t r u c t i o n
Plexus
5 Installation of product
5.1 Handling of product
For the handling of the product please refer to 2.5.
5.2 Ceiling systems
1 T24/T15 Lay-in 600
( I-60 ) Water
Danotile T24/T25
Echophon T24
Rockfon A24
595x595
2 T24/T15 Lay-in 600
not cleanable
( I-60 ) Water
3 Permanent ceiling
( I ) Water
6 Luxalon SQ Clip-In
( X ) Water
595x595
Frame follows the box
( X ) Water
5 Dampa Clip-in square edge
( X ) Water
600x600
600x600
8 Ecophon Focus DG
592x592
9 Rockfon E10 24
Ecophon - E / T24
( Y ) Water
575x575
11
599x599
( I ) Water
chamfer 45°x3
10
( X ) Water
15
7 Danotile Contur
Ecophon D
Rockfon D-XL
chamfer 45°x5
13
600x600
16
26
4 Dampa Clip-in bevelled edge
8
10 Rockfon E10 15
Ecophon - E / T15
( Z ) Water
11 Danotile Markant
( Y ) Water
14 Ecophon Focus DS
Rockfon Sonar X
( X ) Water
599x599
584x584
21 T24/T15 Lay-in-625
( I-62 ) Water
31 T24/T15 Lay-in-675
( I-67 ) Water
22 T24/T15 Lay-in- 625
not cleanable
( I-62 ) Water
32 T24/T15 Lay-in- 675
not cleanable
( I-67 ) Water
619x619
20
669x669
We reserve the right to make changes without prior notice
03-04-2017
15
10
13
575x575
l i nda b | we si mpl i f y c onst ru ction
Plexus
5.3 General installation principles
5.3.1 Recessed in suspended T-bar ceiling
5.3.4 Free hanging above perforated or eggcrate ceiling
5.3.2 Exposed, sealed to the ceiling
5.3.5 Recessed in suspended (permanent)
ceiling
5.3.3 Exposed, free hanging
5.3.6 Recessed in suspended (permanent)
ceiling without cover flanges
We reserve the right to make changes without prior notice
03-04-2017
21
lin dab | w e s i m p l i fy c o n s t r u c t i o n
Plexus
476
128
11
5.4 Preparation for installation on the product
40
Øv
ØH
The beam is prepared for installation by hangers (4 x per beam). 4 turnable/bendable brackets on the Plexus’ models
ensures the possibility to use different hanger systems.
35
17.5
49
220
• Threaded rods M6/M8
Plexus 60 : 371 x 497mm Plexus 120 : 371 x 1097mm
• Pendulum hangers (in different sizes)
: 371 x 477mm: 371 x 1077mm
: 371 x 477mm:40371 x 1077mm
• Lindab FH-System (Gripple® - hang fast system)
70
1
x4
2
x4
3
x4
497 (Plexus 120 = 1097)
A
371
22
We reserve the right to make changes without prior notice
03-04-2017
l i nda b | we si mpl i f y c onst ru ction
Plexus
A
B
C
D
E
A
B
C
D
We reserve the right to make changes without prior notice
03-04-2017
23
lin dab | w e s i m p l i fy c o n s t r u c t i o n
Plexus
5.5.1 Basics steps of installing the product
Plexus
Plexus
Plexus
Plexus
Plexus
Ceilingtype 1, 2, 8, 9 ,10, 11, 21, 22, 31, 32 (Plexus I, Y, Z)
8, 9, 10, 11
1, 2, 21, 22, 31, 32
A
x4
C
B
10-25
kg !
24
S/SA-60 (1)
I-62
(21, 22)
I-67
(31, 32)
Y
(9, 11)
Z
(10)
We reserve the right to make changes without prior notice
03-04-2017
x4
l i nda b | we si mpl i f y c onst ru ction
Plexus
Ceilingtype 3 Permanent ceiling, (Plexus I)
Cutout dimensions in permanent ceilings:
Plexus I (S/SA, L, M, H) 60 =
Plexus I (S/SA) 120
=
Plexus I-62 (S, L, M, H)
=
Plexus I-67 (S, L, M, H)
=
544 x 544 mm
544 x 1144 mm
569 x 569 mm
619 x 619 mm
3
x4
A
C
x4
B
10-25
kg !
We reserve the right to make changes without prior notice
03-04-2017
25
lin dab | w e s i m p l i fy c o n s t r u c t i o n
Plexus
Ceilingtype 4, 5, 6, 7, 14 (Plexus X)
4, 5, 6, 7, 14
x4
A
C
B
10-25
kg !
26
We reserve the right to make changes without prior notice
03-04-2017
x4
l i nda b | we si mpl i f y c onst ru ction
Plexus
Freehanging, exposed (Plexus F)
A
x2
B
x4
C
x4
D
x4
E
x4
F
x2
We reserve the right to make changes without prior notice
03-04-2017
27
lin dab | w e s i m p l i fy c o n s t r u c t i o n
Plexus
6 Adjustment and commissioning
6.1 Airflow and pressure
The JetCone System enables an easy and fast adjustment in both pressure and air volume (primary airflow rate) through
the front side.
6.1.1 Jetcone adjustment pins
Plexus S/SA seen from below with faceplate of.
Plexus L, M, H seen from below with faceplate of.
Adjustment pins
Adjustment pins
Plexus S/SA
Plexus L, M, H
x4
x4
Fixed parts
Fixed parts
Pos. 4
Pos. 4
}
Plexus
S
Plexus - S/SA
pos. 0
28
Plexus L - M - H
pos. 4
We reserve the right to make changes without prior notice
03-04-2017
}
Plexus
L, M, H
nature
l i nda b | we si mpl i f y c onst ru ction
Plexus
6.1.2 Finding values for JetCone pins
Example:
Plexus-I-L-60-12-125-A5-70-16
∆pstat = 70 Pa
(Static pressure).
qa
= 16 (l/s)
(Primary airflow rate)
Δpstat [Pa]
JetCones
Plexus L60
0
120
1
2
3
Position of JetCone adjustment pins
4
5
6
7
8
9
100
1
3
Date
Pstat [Pa]
qa [l/s]
1
2
3
4
Signature
80
70
60
Pos.
0-9
2
50
40
4
30
4
5
6
20
Rev. 04-2012
7
8
9
10
30
15
40
50
20
60
70
25
80
30
35
100
Plexus_label.indd 3
Δpstat [Pa]
40
150
qa [l/s]
qa [m3/h]
25-02-2016 15:48:12
Plexus L60
0
120
1
2
3
Position of JetCone adjustment pins
4
5
6
7
8
9
100
80
70
60
50
40
30
4
5
6
7
20
8
9
30
10
15
40
50
20
60
70
25
80
30
35
40
100
150
qa [l/s]
qa [m3/h]
25-02-2016 15:48:12
6.1.3 Finding values for JetCone pins
Symmetric adjustment
Asymmetric adjustment
2
4
3
Keep average value as read in diagram. (=4)
6
We reserve the right to make changes without prior notice
03-04-2017
5
29
lin dab | w e s i m p l i fy c o n s t r u c t i o n
Plexus
6.2 Adjustment of air distribution profile
Plexus comes as standard (S) with fixed angled JetCone Nozzles and (L, M, H) with fixed air deflectors, which provide
360˚ optimal air distribution.
6.3 Measuring air pressure and calculating the air flow
Before calculating the airflow, the static nozzle pressure must first be measured. The static nozzle pressure is the air
pressure available at the nozzles.
6.3.1 Measuring static nozzle pressure and air pressure
• To measure the air pressure, a manometer, ( analogue or digital ) will be needed. Lindab recommends PC410.
• Insert the measuring tube onto the specialized measuring nozzle.
• Read of the static nozzle pressure from the manometer (PC410).
Lindab PC410
Order no: 103344
Pstat
Room
6.3.2 Calculating the actual air flow
• After measuring the static pressure, read the settings of the four JetCone adjustment pins to find the mean value of the
pins.
• Locate the diagram inside the openable perforated faceplate, (also see next page), and use the static nozzle pressure
and the mean value of the pins to find the current airflow.
6.3.3 Changing the actual air flow
• Measure the static nozzle pressure.
• Locate the air pressure/airflow diagram inside the openable perforated faceplate. (Also see diagrams on next page).
• Find the mean value of the 4 pins to reach the desired airflow, in the diagram. Use the static nozzle pressure and the
desired airflow to find the mean value of the 4 pins.
• Adjust the 4 pins in the Plexus, so the mean value of the pins will correspond with the mean value found in the diagram.
• See example in 6.1.3 , asymmetric pin setting: 2 + 3 + 5 + 6 = 16/4 = 4 . ( Where (4) was the value read in diagram).
6.3.4 Changing the air distribution profile
See 6.1.3.
30
We reserve the right to make changes without prior notice
03-04-2017
nature
nature
nature
nature
l i nda b | we si mpl i f y c onst ru ction
Plexus
6.3.5 Plexus pressure / airflow diagrams
Plexus S/SA60
S60
ΔpStat [Pa] Plexus
0
120
1
2
3
Position of JetCone adjustment pins
4
5
6
7
8
9
100
80
70
60
50
40
30
4
5
6
7
8
20
9
10
30
40
20
50
60
25
70
30
80
35
100
40
150
qa [l/s]
qa [m3/h]
09-02-2016 14:15:56
Plexus
Plexus S/SA120
S120
Δpstat [Pa]
15
0
120
1
2
3
Position of JetCone adjustment pins
4
5
6
35
40
7
8
9
100
80
70
60
50
40
30
8
9
10
30
11
13
40
15
50
20
60
25
70
80
100
50
60
150
200
70
250
qa [l/s]
qa [m3/h]
09-02-2016 14:15:58
Plexus L60
Δpstat [Pa]
30
0
120
1
2
3
Position of JetCone adjustment pins
4
5
6
7
8
9
100
80
70
60
50
40
30
4
5
6
7
8
20
Δpstat [Pa]
9
10
30
15
40
20
50
Plexus M60
0
120
60
1
2
25
70
80
30
35
100
40
150
qa [l/s]
qa [m3/h]
25-02-2016
Position of JetCone adjustment
pins 15:48:12
3
4
5
6
7 8
9
100
80
70
60
50
40
30
10
15
40
50
20
60
70
25
80
30
100
35
40
150
50
60
200
qa [l/s]
qa [m3/h]
09-02-2016 14:16:00
We reserve the right to make changes without prior notice
03-04-2017
31
lin dab | w e s i m p l i fy c o n s t r u c t i o n
Plexus
Δpstat [Pa]
Plexus H60
0 1
120
Position of JetCone adjustment pins
2
3 4
5 6 7 8 9
100
Signature
80
70
60
50
40
30
20
70
25
80
90
30
35
40
100
50
150
60
200
70
250
80
300
qa [l/s]
qa [m3/h]
09-02-2016 14:16:02
6.4 Water flow rate
6.4.1 Pre-setting of valves
For the presetting of valves, please see the TTR/TTV water valves documentation.
6.4.2 Balancing strategy
Lindab recommends always balancing the water system to guarantee thermal comfort in all areas, to avoid noise nuisance
problems and to safe energy. A hydraulic balance is obvious to ensure that all the beams (panels or facade units) in the
system will be always supplied with their required (planned) water flow rates (calculated with “Water Calculator on www.
lindQST.com).
Lindab refers to the proportional method, where all beams (panels or facade units) are balanced to the same proportion of
the requested water flow rate (for example Broen, www.ballorex.com)
32
We reserve the right to make changes without prior notice
03-04-2017
l i nda b | we si mpl i f y c onst ru ction
Plexus
7. Maintenance
The interval of cleaning depends on the indoor environment where the beam is placed. Under optimal conditions the
beams only need cleaning every 5 years.
•
•
•
•
•
•
•
Open the inlet plate using no tools (7.2)
Clean the battery downside and the inlet faceplate inner parts with a dust cleaner / vacuum cleaner.
Only use lukewarm water and a mild detergent and a piece of wet cloth to clean the inlet face plate.
Open the inspection hatch (7.3)
Clean the air plenum chamber and air connection with a vacuum cleaner
Lower battery if water pipe connections are connected to system by flexhoses. ( Otherwise this is not possible, See7.4).
Clean the top side of the battery, nozzle plate, JetCones and the mixing chamber with a dust cleaner / vacuum cleaner.
7.1 Remove the outlet front grille
Not relevant for Plexus.
7.2 Open inlet faceplate
7.3 Opening inspection hatch
Service wires
We reserve the right to make changes without prior notice
03-04-2017
33
lin dab | w e s i m p l i fy c o n s t r u c t i o n
Plexus
7.4 Lower battery
Battery can only be lowered when the plus feature “dropdown battery” is ordered.
A
x2
M4x30
B
B
A
!
A
Do not unscrew completely!
B x2
X
Plexus 60 => X = 25 mm
Plexus 120 => X = 15 mm
Plexus 120
Plexus 60
C
Flex-tubes
Service wire
34
We reserve the right to make changes without prior notice
03-04-2017
l i nda b | we si mpl i f y c onst ru ction
Plexus
8 Accessories
Ask Lindab for the accessories mentioned in this document. Additional accessories (or additional dimensions) are
available on request.**
Order code
Order number
2-way valve Broen TTR-12 Thermostatic valve - Tectite
647832
2-way valve Broen TTV-12 Thermostatic valve - Tectite
647834
Actuator A 40405 24 V on/off NC - 1m, non-halogen cable
684601
Actuator A 41405 24 V on/off NO - 1m, non-halogen cable
684603
Actuator APR 40405 0-10 V mod. NC, 1m, non-halogen cable
684667
Actuator APR 40405 0-10 V mod. NC, 1m, cable
684604
Ballofix Broen 12mm with handle - shut-off valve
642663
Ballofix Broen 12mm without handle - shut-off valve
642662
Ballorex dynamics 15mm Push-on
682474
Copper insert 12x1,0mm
884022
Lindab FHS-2-1000 (incl. M8 drop-in anchor)
100089
Flexible hose 0,4m push-on 12 and 12 mm
680080
Lindab PC 410
103344
Pendulum 180-300mm
642480
Pendulum 540-1000mm
646742
**
Regula Combi see: "Accessories"
Regula Connect Card Basic
*/**
Regula Connect Card Multi
*/**
**
Regula Secura
Aerator 12mm - tectite
647690
Tectite angle 12mm
884014
Tectite straight 12mm
884050
Tectite demounting tool 12mm
884087
Tectite demounting tool 12mm small
646881
4 pcs Threaded rod M8 -100mm + 4 pcs z-brackets + 16 pcs screw nuts
on request
642531
Touch-up paint RAL 9010 - 10ml
*/**
Transformer 24V AC output
*see: ”Regula Connect – What do I get?”
**see: ”Accessories”
We reserve the right to make changes without prior notice
03-04-2017
35
At Lindab, good thinking is a philosophy that guides us in everything we do. We have made it our
mission to create a healthy indoor climate – and
to simplify the construction of sustainable buildings. We do that by designing innovative products and solutions that are easy to use, as well
as offering efficient availability and logistics. We
are also working on ways to reduce our impact on
our environment and climate. We do that by developing methods to produce our solutions using
a minimum of energy and natural resources, and
by reducing negative effects on the environment.
We use steel in our products. It’s one of few materials that can be recycled an infinite number of times
without losing any of its properties. That means
less carbon emissions in nature and less energy
wasted.
We simplify construction
www.lindab.com

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project