Lenovo IdeaPad Yoga 2 Maintenance Manual

Lenovo Yoga 2 11

Hardware

Maintenance

Manual

Notes:

• Before using this information and the product it supports, be sure to read the general information under

“Notices” on page 71.

First Edition (Dec. 2013)

© Copyright Lenovo 2013. All rights reserved.

LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General

Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.

© 2013 Lenovo

Contents

About this manual ....................................... iv

Safety information ........................................ 1

General safety ................................................ 2

Electrical safety .............................................. 3

Safety inspection guide .................................. 5

Handling devices that are sensitive to electrostatic discharge .................................... 6

Grounding requirements ................................. 6

Safety notices: multilingual translations.......... 7

Laser compliance statement......................... 14

Important service information ................... 16

Strategy for replacing FRUs ......................... 16

Strategy for replacing a hard disk drive ............17

Important notice for replacing a system board ................................................................17

Important information about replacing RoHS compliant FRUs ............................................ 18

General checkout ...................................... 19

What to do first ............................................. 20

Power system checkout................................ 21

Checking the AC adapter .................................21

Checking operational charging .........................21

Related service information ...................... 23

Restoring the factory contents by using

OneKey Recovery ........................................ 23

Restore of factory default .................................23

Passwords .................................................... 24

Power-on password ..........................................24

Hard-disk password ..........................................24

Supervisor password ........................................24

Power management ..................................... 25

Screen blank state ............................................25

Putting the computer to sleep or shutting it down .................................................................25

Putting your computer to sleep .........................25

Shutting down the computer .............................26

Lenovo Yoga 2 11 ....................................... 27

Specifications ............................................... 27

Status indicators ........................................... 29

Fn key combinations..................................... 30

FRU replacement notices ............................. 31

Screw notices ..................................................31

Removing and replacing an FRU ................. 32

1010 Base cover ...............................................33

1020 Battery pack .............................................35

1030 Hard disk drive ........................................36

1040 PCI Express Mini Card for wireless

LAN ...................................................................38

1050 System board ..........................................39

1060 Speakers .................................................42

1070 LCD unit ...................................................43

1080 Power board and power assembly ..........45

1090 LCD front cover .......................................46

1100 Win8 home board, LCD cover, and hinges ...............................................................48

1110 LCD module .............................................51

Locations ...................................................... 54

Front view and right-side view ..........................54

Bottom and Left-side view ...............................55

Parts list ........................................................ 56

Overall ..............................................................57

LCD FRUs ........................................................61

Keyboard ..........................................................63

Miscellaneous parts ..........................................65

Screw ................................................................65

AC adapters ......................................................66

Power cords ......................................................67

Notices......................................................... 71

Trademarks .................................................. 72 iii

About this manual

This manual contains service and reference information for the following

Lenovo product:

Lenovo Yoga 2 11

Use this manual to troubleshoot problems.

The manual is divided into the following sections:

• The common sections provide general information, guidelines, and safety information required for servicing computers.

• The product-specific section includes service, reference, and product-specific parts information.

Important:

This manual is intended only for trained servicers who are familiar with Lenovo products. Use this manual to troubleshoot problems effectively.

Before servicing a Lenovo product, make sure to read all the information under

“Safety information” on page 1 and “Important service information” on page 16. iv

Safety information

Safety information

This chapter presents the following safety information that you need to get familiar with before you service a Lenovo Yoga 2 11 computer:

• “General safety” on page 2

• “Electrical safety” on page 3

• “Safety inspection guide” on page 5

• “Handling devices that are sensitive to electrostatic discharge” on page 6

• “Grounding requirements” on page 6

• “Safety notices: multilingual translations” on page 7

• “Laser compliance statement” on page 14

1

2

Lenovo Yoga 2 11 Hardware Maintenance Manual

General safety

Follow these rules below to ensure general safety:

• Observe a good housekeeping in the area where the machines are put during and after the maintenance.

• When lifting any heavy object:

1. Make sure that you can stand safely without slipping.

2. Distribute the weight of the object equally between your feet.

3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift it.

4. Lift it by standing or pushing up with your leg muscles; this action could avoid the strain from the muscles in your back. Do not attempt to lift any object that weighs more than 16 kg (35 lb) or that you think is too heavy for you.

• Do not perform any action that causes hazards to the customer, or that makes the machine unsafe.

• Before you start the machine, make sure that other service representatives and the customer are not in a hazardous position.

• Please remove covers and other parts in a safe place, away from all personnel, while you are servicing the machine.

• Keep your toolcase away from walk areas so that other people will not trip over it.

• Do not wear loose clothing that can be trapped in the moving parts of the machine. Make sure that your sleeves are fastened or rolled up above your elbows. If your hair is long, fasten it.

• Insert the ends of your necktie or scarf inside clothing or fasten it with the nonconductive clip, about 8 centimeters (3 inches) from the end.

• Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your clothing.

Attention: Metal objects are good electrical conductors.

• Wear safety glasses when you are hammering, drilling, soldering, cutting wire, attaching springs, using solvents, or working in any other conditions that may be hazardous to your eyes.

• After service, reinstall all safety shields, guards, labels, and ground wires.

Replace any safety device that is worn or defective.

• Reinstall all covers correctly before returning the machine to the customer.

• Fan louvers on the machine help to prevent the overheating of internal components. Do not obstruct fan louvers or cover them with labels or stickers.

About this manual

Electrical safety

Observe the following rules when working on electrical equipments.

Important:

Use only approved tools and test equipments. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents.

Many customers have rubber floor mats near their machines that contain small conductive fibers to decrease electrostatic discharges. Do not use such kind of mat to protect yourself from electrical shock.

• Find the room emergency power-off (EPO) switch, disconnecting switch or electrical outlet. If an electrical accident occurs, you can then operate the switch or unplug the power cord quickly.

• Do not work alone under hazardous conditions or near the equipment that has hazardous voltages.

• Disconnect all power before:

– Performing a mechanical inspection

– Working near power supplies

– Removing or installing main units

• Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer to power-off the wall box that supplies power to the machine, and to lock the wall box in the off position.

• If you need to work on a machine that has exposed electrical circuits, observe the following precautions:

– Ensure that another person, familiar with the power-off controls, is near you.

Attention: Another person must be there to switch off the power, if necessary.

– Use only one hand when working with powered-on electrical equipment; keep the other hand in your pocket or behind your back.

Attention: An electrical shock can occur only when there is a complete circuit. By observing the above rule, you may prevent a current from passing through your body.

– When using testers, set the controls correctly and use the approved probe leads and accessories for that tester.

– Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as metal floor strips and machine frames.

Observe the special safety precautions when you work with very high voltages; instructions for these precautions are in the safety sections of maintenance information. Be extremely careful when you measure the high voltages.

• Regularly inspect and maintain your electrical hand tools for safe operational condition.

• Do not use worn or broken tools and testers.

• Never assume that power has been disconnected from a circuit. First, check it to make sure that it has been powered off.

3

4


• Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors, nongrounded power extension cables, power surges, and missing safety grounds.

• Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage.

• Do not service the following parts with the power on when they are removed from their normal operating places in a machine:

– Power supply units

– Pumps

– Blowers and fans

– Motor generators and similar units. (This practice ensures correct grounding of the units.)

• If an electrical accident occurs:

– Caution: do not become a victim yourself.

– Switch off the power.

– Send the victim to get medical aid.

About this manual

Safety inspection guide

The purpose of this inspection guide is to assist you in identifying potential unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service personnel from injury. This guide addresses only those items. You should use good judgment to identify potential safety hazards according to the attachment of non-Lenovo features or options not covered by this inspection guide.

If any unsafe conditions are present, you must determine how serious the apparent hazard could be and whether you can continue without first correcting the problem.

Consider these conditions and the safety hazards they present:

• Electrical hazards, especially primary power (primary voltage on the frame can cause serious or fatal electrical shock)

• Explosive hazards, such as a damaged CRT face or a bulging capacitor

• Mechanical hazards, such as loose or missing hardware

To determine whether there are any potential unsafe conditions, use the following checklist at the beginning of every service task. Begin the checks with the power off, and the power cord disconnected.

Checklist:

1. Check exterior covers for damage (loose, broken, or sharp edges).

2. Turn off the computer. Disconnect the power cord.

3. Check the power cord for: a. A third-wire ground connector in good condition. Use a meter to measure third-wire ground continuity for 0.1 ohm or less between the external ground pin and the frame ground.

b. The power cord should be the type specified in the parts list.

c. Insulation must not be frayed or worn.

4. Check for cracked or bulging batteries.

5. Remove the cover.

6. Check for any obvious non-Lenovo alterations. Use good judgment as to the safety of any non-Lenovo alterations.

7. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or other liquids, or signs of fire or smoke damage.

8. Check for worn, frayed, or pinched cables.

9. Check that the power-supply cover fasteners (screws or rivets) have not been removed or tampered with.

5

6


Handling devices that are sensitive to electrostatic discharge

Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge.

Notes:

1. Use product-specific ESD procedures when they exceed the requirements noted here.

2. Make sure that the ESD protective devices you use have been certified (ISO

9000) as fully effective.

When handling ESD-sensitive parts:

• Keep the parts in protective packages until they are inserted into the product.

• Avoid contact with other people.

• Wear a grounded wrist strap against your skin to eliminate static on your body.

• Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when you are wearing a wrist strap.

• Use the black side of a grounded work mat to provide a static-free work surface. The mat is especially useful when handling ESD-sensitive devices.

• Select a grounding system, such as those listed below, to provide protection that meets the specific service requirement.

Note:

The use of a grounding system to guard against ESD damage is desirable but not necessary.

– Attach the ESD ground clip to any frame ground, ground braid, or greenwire ground.

– When working on a double-insulated or battery-operated system, use an

ESD common ground or reference point. You can use coax or connectoroutside shells on these systems.

– Use the round ground prong of the ac plug on ac-operated computers.

Grounding requirements

Electrical grounding of the computer is required for operator safety and correct system function. Proper grounding of the electrical outlet can be verified by a certified electrician.

About this manual

Safety notices: multilingual translations

The safety notices in this section are provided in English, French, German,

Hebrew, Italian, Japanese, and Spanish.

Safety notice 1

Before the computer is powered on after FRU replacement, make sure all screws, springs, and other small parts are in place and are not left loose inside the computer. Verify this by shaking the computer and listening for rattling sounds.

Metallic parts or metal flakes can cause electrical shorts.

Avant de remettre l’ordinateur sous tension après remplacement d’une unité en clientèle, vérifiez que tous les ressorts, vis et autres pièces sont bien en place et bien fixées. Pour ce faire, secouez l’unité et assurez-vous qu’aucun bruit suspect ne se produit. Des pièces métalliques ou des copeaux de métal pourraient causer un court-circuit.

Bevor nach einem FRU-Austausch der Computer wieder angeschlossen wird, muß sichergestellt werden, daß keine Schrauben, Federn oder andere Kleinteile fehlen oder im Gehäuse vergessen wurden. Der Computer muß geschüttelt und auf

Klappergeräusche geprüft werden. Metallteile oder-splitter können Kurzschlüsse erzeugen.

Prima di accendere l’elaboratore dopo che é stata effettuata la sostituzione di una

FRU, accertarsi che tutte le viti, le molle e tutte le altri parti di piccole dimensioni siano nella corretta posizione e non siano sparse all’interno dell’elaboratore.

Verificare ciò scuotendo l’elaboratore e prestando attenzione ad eventuali rumori; eventuali parti o pezzetti metallici possono provocare cortocircuiti pericolosi.

Antes de encender el sistema despues de sustituir una FRU, compruebe que todos los tornillos, muelles y demás piezas pequeñas se encuentran en su sitio y no se encuentran sueltas dentro del sistema. Compruébelo agitando el sistema y escuchando los posibles ruidos que provocarían. Las piezas metálicas pueden causar cortocircuitos eléctricos.

7

8


Safety notice 2

DANGER

Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble a standby battery, recharge it, throw it into fire or water, or shortcircuit it. Dispose of the battery as required by local ordinances or regulations.

Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery.

Certaines batteries de secours contiennent du nickel et du cadmium. Ne les démontez pas, ne les rechargez pas, ne les exposez ni au feu ni à l’eau. Ne les mettez pas en court-circuit. Pour les mettre au rebut, conformez-vous à la réglementation en vigueur. Lorsque vous remplacez la pile de sauvegarde ou celle de l’horloge temps réel, veillez à n’utiliser que les modèles cités dans la liste de pièces détachées adéquate. Une batterie ou une pile inappropriée risque de prendre feu ou d’exploser.

Die Bereitschaftsbatterie, die sich unter dem Diskettenlaufwerk befindet, kann geringe Mengen Nickel und Cadmium enthalten. Sie darf nicht zerlegt, wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden.

Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Beim

Ersetzen der Bereitschafts-oder Systembatterie nur Batterien des Typs verwenden, der in der Ersatzteilliste aufgeführt ist. Der Einsatz falscher Batterien kann zu

Entzündung oder Explosion führen.

Alcune batterie di riserva contengono una piccola quantità di nichel e cadmio.

Non smontarle, ricaricarle, gettarle nel fuoco o nell’acqua né cortocircuitarle.

Smaltirle secondo la normativa in vigore (DPR 915/82, successive disposizioni e disposizioni locali). Quando si sostituisce la batteria dell’RTC (real time clock) o la batteria di supporto, utilizzare soltanto i tipi inseriti nell’appropriato Catalogo parti. L’impiego di una batteria non adatta potrebbe determinare l’incendio o l’esplosione della batteria stessa.

Algunas baterías de reserva contienen una pequeña cantidad de níquel y cadmio.

No las desmonte, ni recargue, ni las eche al fuego o al agua ni las cortocircuite.

Deséchelas tal como dispone la normativa local. Utilice sólo baterías que se encuentren en la lista de piezas. La utilización de una batería no apropiada puede provocar la ignición o explosión de la misma.

About this manual

Safety notice 3

DANGER

The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or water, or short-circuit it. Dispose of the battery pack as required by local ordinances or regulations. Use only the battery in the appropriate parts listing when replacing the battery pack. Use of an incorrect battery can result in ignition or explosion of the battery.

La batterie contient du nickel. Ne la démontez pas, ne l’exposez ni au feu ni à l’eau.

Ne la mettez pas en court-circuit. Pour la mettre au rebut, conformez-vous à la réglementation en vigueur. Lorsque vous remplacez la batterie, veillez à n’utiliser que les modèles cités dans la liste de pièces détachées adéquate. En effet, une batterie inappropriée risque de prendre feu ou d’exploser.

Akkus enthalten geringe Mengen von Nickel. Sie dürfen nicht zerlegt, wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden.

Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Beim

Ersetzen der Batterie nur Batterien des Typs verwenden, der in der Ersatzteilliste aufgeführt ist. Der Einsatz falscher Batterien kann zu Entzündung oder Explosion führen.

La batteria contiene piccole quantità di nichel. Non smontarla, gettarla nel fuoco o nell’acqua né cortocircuitarla. Smaltirla secondo la normativa in vigore (DPR

915/82, successive disposizioni e disposizioni locali). Quando si sostituisce la batteria, utilizzare soltanto i tipi inseriti nell’appropriato Catalogo parti. L’impiego di una batteria non adatta potrebbe determinare l’incendio o l’esplosione della batteria stessa.

Las baterías contienen pequeñas cantidades de níquel. No las desmonte, ni recargue, ni las eche al fuego o al agua ni las cortocircuite. Deséchelas tal como dispone la normativa local. Utilice sólo baterías que se encuentren en la lista de piezas al sustituir la batería. La utilización de una batería no apropiada puede provocar la ignición o explosión de la misma.

9

10


Safety notice 4

DANGER

The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it, remove its polarized connector, disassemble it, heat it above 100°C

(212°F), incinerate it, or expose its cell contents to water. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery.

La pile de sauvegarde contient du lithium. Elle présente des risques d’incendie, d’explosion ou de brûlures graves. Ne la rechargez pas, ne retirez pas son connecteur polarisé et ne la démontez pas. Ne l’exposez pas à une temperature supérieure à 100°C, ne la faites pas brûler et n’en exposez pas le contenu à l’eau.

Mettez la pile au rebut conformément à la réglementation en vigueur. Une pile inappropriée risque de prendre feu ou d’exploser.

Die Systembatterie ist eine Lithiumbatterie. Sie kann sich entzünden, explodieren oder schwere Verbrennungen hervorrufen. Batterien dieses Typs dürfen nicht aufgeladen, zerlegt, über 100 C erhitzt oder verbrannt werden. Auch darf ihr

Inhalt nicht mit Wasser in Verbindung gebracht oder der zur richtigen Polung angebrachte Verbindungsstecker entfernt werden. Bei der Entsorgung die örtlichen

Bestimmungen für Sondermüll beachten. Beim Ersetzen der Batterie nur Batterien des Typs verwenden, der in der Ersatzteilliste aufgeführt ist. Der Einsatz falscher

Batterien kann zu Entzündung oder Explosion führen.

La batteria di supporto e una batteria al litio e puo incendiarsi, esplodere o procurare gravi ustioni. Evitare di ricaricarla, smontarne il connettore polarizzato, smontarla, riscaldarla ad una temperatura superiore ai 100 gradi centigradi, incendiarla o gettarla in acqua. Smaltirla secondo la normativa in vigore (DPR

915/82, successive disposizioni e disposizioni locali). L’impiego di una batteria non adatta potrebbe determinare l’incendio o l’esplosione della batteria stessa.

La batería de repuesto es una batería de litio y puede provocar incendios, explosiones o quemaduras graves. No la recargue, ni quite el conector polarizado, ni la desmonte, ni caliente por encima de los 100°C (212°F), ni la incinere ni exponga el contenido de sus celdas al agua. Deséchela tal como dispone la normativa local.

About this manual

Safety notice 5

If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands, immediately wash the affected areas with water at least for 15 minutes.

Seek medical care if any symptoms caused by the fluid are present after washing.

Si le panneau d’affichage à cristaux liquides se brise et que vous recevez dans les yeux ou sur les mains une partie du fluide, rincez-les abondamment pendant au moins quinze minutes. Consultez un médecin si des symptômes persistent après le lavage.

Die Leuchtstoffröhre im LCD-Bildschirm enthält Quecksilber. Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Der LCD-Bildschirm besteht aus Glas und kann zerbrechen, wenn er unsachgemäß behandelt wird oder der Computer auf den Boden fällt. Wenn der Bildschirm beschädigt ist und die darin befindliche Flüssigkeit in Kontakt mit Haut und Augen gerät, sollten die betroffenen Stellen mindestens 15 Minuten mit Wasser abgespült und bei

Beschwerden anschließend ein Arzt aufgesucht werden.

Nel caso che caso l’LCD si dovesse rompere ed il liquido in esso contenuto entrasse in contatto con gli occhi o le mani, lavare immediatamente le parti interessate con acqua corrente per almeno 15 minuti; poi consultare un medico se i sintomi dovessero permanere.

Si la LCD se rompe y el fluido de su interior entra en contacto con sus ojos o sus manos, lave inmediatamente las áreas afectadas con agua durante 15 minutos como mínimo. Obtenga atención medica si se presenta algún síntoma del fluido despues de lavarse.

11

12


Safety notice 6

DANGER

To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card.

Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique protégeant la partie inférieure de la carte d’alimentation.

Aus Sicherheitsgründen die Kunststoffabdeckung, die den unteren Teil der

Spannungswandlerplatine umgibt, nicht entfernen.

Per evitare scosse elettriche, non rimuovere la copertura in plastica che avvolge la parte inferiore della scheda invertitore.

Para evitar descargas, no quite la cubierta de plástico que rodea la parte baja de la tarjeta invertida.

Safety notice 7

DANGER

Though the main batteries have low voltage, a shorted or grounded battery can produce enough current to burn personnel or combustible materials.

Bien que le voltage des batteries principales soit peu élevé, le court-circuit ou la mise à la masse d’une batterie peut produire suffisamment de courant pour brûler des matériaux combustibles ou causer des brûlures corporelles graves.

Obwohl Hauptbatterien eine niedrige Spannung haben, können sie doch bei

Kurzschluß oder Erdung genug Strom abgeben, um brennbare Materialien zu entzünden oder Verletzungen bei Personen hervorzurufen.

Sebbene le batterie di alimentazione siano a basso voltaggio, una batteria in corto circuito o a massa può fornire corrente sufficiente da bruciare materiali combustibili o provocare ustioni ai tecnici di manutenzione.

Aunque las baterías principales tienen un voltaje bajo, una batería cortocircuitada o con contacto a tierra puede producir la corriente suficiente como para quemar material combustible o provocar quemaduras en el personal.

About this manual

Safety notice 8

DANGER

Before removing any FRU, turn off the computer, unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any interconnecting cables.

Avant de retirer une unité remplaçable en clientèle, mettez le système hors tension, débranchez tous les cordons d’alimentation des socles de prise de courant, retirez la batterie et déconnectez tous les cordons d’interface.

Die Stromzufuhr muß abgeschaltet, alle Stromkabel aus der Steckdose gezogen, der Akku entfernt und alle Verbindungskabel abgenommen sein, bevor eine FRU entfernt wird.

Prima di rimuovere qualsiasi FRU, spegnere il sistema, scollegare dalle prese elettriche tutti i cavi di alimentazione, rimuovere la batteria e poi scollegare i cavi di interconnessione.

Antes de quitar una FRU, apague el sistema, desenchufe todos los cables de las tomas de corriente eléctrica, quite la batería y, a continuación, desconecte cualquier cable de conexión entre dispositivos.

13


Laser compliance statement

Some models of Lenovo computer are equipped from the factory with an optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are also sold separately as options. If one of these drives is installed, it is certified in the U.S. to conform to the requirements of the Department of

Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR)

Subchapter J for Class 1 laser products. Elsewhere, the drive is certified to conform to the requirements of the International Electrotechnical Commission

(IEC) 825 and CENELEC EN 60 825 for Class 1 laser products.

If a CD-ROM drive, a DVD-ROM drive, or another laser device is installed, note the following:

CAUTION

Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure.

O uso de controles, ajustes ou desempenho de procedimentos diferentes daqueles aqui especificados pode resultar em perigosa exposição à radiação.

Pour éviter tout risque d’exposition au rayon laser, respectez les consignes de réglage et d’utilisation des commandes, ainsi que les procédures décrites.

Werden Steuer- und Einstellelemente anders als hier festgesetzt verwendet, kann gefährliche Laserstrahlung auftreten.

L’utilizzo di controlli, regolazioni o l’esecuzione di procedure diverse da quelle specificate possono provocare l’esposizione a.

El uso de controles o ajustes o la ejecución de procedimientos distintos de los aquí especificados puede provocar la exposición a radiaciones peligrosas.

Opening the CD-ROM drive, the DVD-ROM drive, or any other optical storage device could result in exposure to hazardous laser radiation. There are no serviceable parts inside those drives. Do not open.

14

About this manual

A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may contain an embedded Class 3A or Class 3B laser diode. Note the following:

DANGER

Emits visible and invisible laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam.

Radiação por raio laser ao abrir. Não olhe fixo no feixe de luz, não olhe diretamente por meio de instrumentos óticos e evite exposição direta com o feixe de luz.

Rayonnement laser si carter ouvert. Évitez de fixer le faisceau, de le regarder directement avec des instruments optiques, ou de vous exposer au rayon.

Laserstrahlung bei geöffnetem Gerät. Nicht direkt oder über optische Instrumente in den Laserstrahl sehen und den Strahlungsbereich meiden.

Kinyitáskor lézersugár ! Ne nézzen bele se szabad szemmel, se optikai eszközökkel. Kerülje a sugárnyalábbal való érintkezést!

Aprendo l’unità vengono emesse radiazioni laser. Non fissare il fascio, non guardarlo direttamente con strumenti ottici e evitare l’esposizione diretta al fascio.

Radiación láser al abrir. No mire fijamente ni examine con instrumental óptico el haz de luz. Evite la exposición directa al haz.

15


Important service information

This chapter presents the following important service information:

• “Strategy for replacing FRUs” on page 16

– “Strategy for replacing a hard disk drive” on page 17

– “Important notice for replacing a system board” on page 17

• “Important information about replacing RoHS compliant FRUs” on page 18

Important:

BIOS and device driver fixes are customer-installable. The BIOS and device drivers are posted on the customer support site: http://support.lenovo.com.

Strategy for replacing FRUs

Before replacing parts:

Make sure that all software fixes, drivers, and BIOS downloads are installed before replacing any FRUs listed in this manual.

After a system board is replaced, ensure that the latest BIOS is loaded to the system board before completing the service action.

To download software fixes, drivers, and BIOS, follow the steps below:

1. Go to http://support.lenovo.com.

2. Enter the serial number or select a product or use Lenovo smart downloading.

3. Select the BIOS/Driver/Applications and download.

4. Follow the directions on the screen and install the necessary software.

16

Important service information

Use the following strategy to prevent unnecessary expense for replacing and servicing FRUs:

• If you are instructed to replace an FRU, but the replacement does not solve the problem, reinstall the original FRU before you continue.

• Some computers have both a processor board and a system board. If you are instructed to replace either of them, and replacing one of them does not solve the problem, reinstall that board, and then replace the other one.

• If an adapter or a device consists of more than one FRU, any of the FRUs may be the cause of the error. Before replacing the adapter or device, remove the FRUs one by one to see if the symptoms change. Replace only the FRU that changed the symptoms.

Attention: The setup configuration on the computer you are servicing may have been customized. Running Automatic Configuration may alter the settings. Note the current configuration settings (using the View Configuration option); then, when service has been completed, verify that those settings remain in effect.

Strategy for replacing a hard disk drive

Always try to run a low-level format before replacing a hard disk drive. This will cause all customer data on the hard disk to be lost. Make sure that the customer has a current backup of the data before performing this action.

Attention: The drive startup sequence in the computer you are servicing may have been changed. Be extremely careful during write operations such as copying, saving, or formatting. If you select an incorrect drive, data or programs can be overwritten.

Important notice for replacing a system board

Some components mounted on a system board are very sensitive. Improper handling can cause damage to those components, and may cause a system malfunction.

Attention: When handling a system board:

• Do not drop the system board or apply any excessive force to it.

• Avoid rough handling of any kind.

• Avoid bending the system board and hard pushing to prevent cracking at each BGA (Ball Grid Array) chipset.

17


Important information about replacing RoHS compliant FRUs

RoHS, The Restriction of Hazardous Substances in Electrical and

Electronic Equipment Directive (2002/95/EC) is a European Union legal requirement affecting the global electronics industry. RoHS requirements must be implemented on Lenovo products placed on the market after

June 2006. Products on the market before June 2006 are not required to have RoHS compliant parts. If the original FRU parts are non-compliant, replacement parts can also be non-compliant. In all cases if the original

FRU parts are RoHS compliant, the replacement part must also be RoHS compliant.

Note: RoHS and non-RoHS FRU part numbers with the same fit and function are identified with unique FRU part numbers.

Lenovo plans to transit to RoHS compliance well before the implementation date and expects its suppliers to be ready to support Lenovo’s requirements and schedule in the EU. Products sold in 2005 and 2006 will contain some

RoHS compliant FRUs. The following statement pertains to these products and any product Lenovo produces containing RoHS compliant FRUs.

RoHS compliant FRUs have unique FRU part numbers. Before or after the

RoHS implementation date, failed RoHS compliant parts must always be replaced with RoHS compliant ones, so only the FRUs identified as compliant in the system HMM or direct substitutions for those FRUs may be used.

Products marketed before June 2006 Products marketed after June 2006

Current or original part

Replacement FRU Current or original part

Replacement FRU

Non-RoHS Can be Non-RoHS

Non-RoHS Can be RoHS

Must be RoHS Must be RoHS

Non-RoHS

RoHS

Can sub to RoHS

Must be RoHS

Note: A direct substitution is a part with a different FRU part number that is automatically shipped by the distribution center at the time of the order.

18

General checkout

General checkout

This chapter presents the following information:

• “What to do first” on page 20

• “Power system checkout” on page 21

Before you go to the checkout, make sure to read the following important notes:

Important notes:

• Only certified trained personnel can service the computer.

• Before replacing any FRU, read the entire page on removing and replacing

FRUs.

• Carefully remove screws for reuse when replacing FRUs.

• Be extremely careful during such write operations as copying, saving, or

formatting. Drives in the computer that you are servicing sequence might have been altered. If you select an incorrect drive, data or programs might be overwritten.

• Replace an FRU only with another FRU of the correct model. When you replace an FRU, make sure that the machine model and the FRU part number are correct by referring to the FRU parts list.

• An FRU should not be replaced just because of a single, unreproducible

failure. Single failures can occur for a variety of reasons that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. Consider replacing an FRU only when a problem recurs. If you suspect that an FRU is defective, clear the error logs and run the test again. If the error does not recur, do not replace the FRU.

• Be careful not to replace a nondefective FRU.

19


What to do first

When you do return an FRU, you must include the following information in the parts exchange form or parts return form that you attach to it:

1. Name and phone number of servicer

2. Date of service

3. Date on which the machine failed

4. Date of purchase

5. Procedure index and page number in which the failing FRU was detected

6. Failing FRU name and part number

7. Machine type, model number, and serial number

8. Customer’s name and address

Note for warranty: During the warranty period, the customer may be responsible for repair costs if the computer damage was caused by misuse, accident, modification, unsuitable physical or operating environment, or improper maintenance by the customer.

The following is a list of some common items that are not covered under warranty and some symptoms that might indicate that the system was subjected to stress beyond normal use.

Before checking problems with the computer, determine whether the damage is covered under the warranty by referring to the following list:

The following are not covered under warranty:

• LCD panel cracked from the application of excessive force or from being dropped

• Scratched (cosmetic) parts

• Distortion, deformation, or discoloration of the cosmetic parts

• Plastic parts, latches, pins, or connectors that have been cracked or broken by excessive force

• Damage caused by liquid spilled into the system

• Damage caused by the improper insertion of a PC Card or the installation of an incompatible card

• Improper disk insertion or use of an optical drive

• Diskette drive damage caused by pressure on the diskette drive cover, foreign material in the drive, or the insertion of a diskette with multiple labels

• Damaged or bent diskette eject button

• Fuses blown by attachment of a nonsupported device

• Forgotten computer password (making the computer unusable)

• Sticky keys caused by spilling a liquid onto the keyboard

• Use of an incorrect AC adapter on laptop products

The following symptoms might indicate damage caused by nonwarranted activities:

• Missing parts might be a symptom of unauthorized service or modification.

• If the spindle of a hard disk drive becomes noisy, it may have been subjected to excessive force, or dropped.

20

General checkout

Power system checkout

To verify a symptom, follow the steps below:

1. Turn off the computer.

2. Connect the AC adapter.

3. Make sure that power is supplied when you turn on the computer.

4. Turn off the computer.

5. Disconnect the AC adapter.

6. Make sure that the battery pack supplies power when you turn on the computer.

If you suspect a power problem, see the appropriate power supply checkout:

• “Checking the AC adapter” on page 21

• “Checking operational charging” on page 21

Checking the AC adapter

You are here because the computer fails only when the AC adapter is used.

• If the power-on indicator does not turn on, check the power cord of the AC adapter for correct continuity and installation.

• If the computer does not charge during operation, go to “Checking operational charging”.

To check the AC adapter, follow the steps below:

1. Unplug the AC adapter cable from the computer.

2. Measure the output voltage at the plug of the AC adapter cable. See the following figure:

Note: Output voltage for the AC adapter pin No. 2 may differ from the one you are servicing.

3. If the voltage is not correct, replace the AC adapter.

4. If the voltage is acceptable, do the following:

• Replace the system board.

• If the problem persists, go to “Lenovo Yoga 2 11” on page 27.

Note: Noise from the AC adapter does not always indicate a defect.

Checking operational charging

To check whether the battery charges properly during operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer.

21

22


Perform operational charging. If the battery status indicator or icon is not lit, remove the battery pack and let it return to room temperature. Reinstall the battery pack. If the charge indicator or icon is still off, replace the battery pack.

If the charge indicator is still not lit, replace the system board.

Related service information

Related service information

This chapter presents the following information:

• “ Restoring the factory contents by using OneKey Recovery” on page 23

• “Passwords” on page 24

• “Power management” on page 25

Restoring the factory contents by using OneKey Recovery

Restore of factory default

The Lenovo Yoga 2 11 computer comes with pre-installed OneKey Recovery

System.In order to save application files and the initial backed up files of the system, the hard disk in a Lenovo computer includes a hidden partition when it is shipped. If you need to restore the system to the point of your first boot up, just enter Lenovo OneKey Recovery System and run System Recovery.

For details of OneKey Recovery System, see the User Guide for Lenovo OneKey

Recovery system .

Note: This will delete all the new data on the system partition (C drive), which is not recoverable. Make sure to back up your critical data before you perform this action.

23


Passwords

As many as three passwords may be needed for any Lenovo computer: the power-on password (POP), the hard disk password (HDP), and the supervisor password.

If any of these passwords has been set, a prompt for it appears on the screen whenever the computer is turned on. The computer does not start until the password is entered.

Power-on password

A power-on password (POP) protects the system from being powered on by an unauthorized person. The password must be entered before an operating system can be booted.

Hard-disk password

There are two hard-disk passwords (HDPs):

+ User HDP - for the user

+ Master HDP - for the system administrator, who can use it to get access to the hard disk drive even if the user has changed the user HDP

Attention: If the user HDP has been forgotten, check whether a master HDP has been set. If it has, it can be used for access to the hard disk drive. If no master HDP is available, neither Lenovo nor Lenov authorized service technicians provide any services to reset either the user or the master HDP, or to recover data from the hard disk drive. The hard disk drive can be replaced for a scheduled fee.

Supervisor password

A supervisor password protects the system information stored in the BIOS. The user must enter the supervisor password to get access to the BIOS and change the system configuration.

Attention: If you forget the password, there is no service procedure to reset the password. The system board must be replaced for a scheduled fee.

24

Related service information

Power management

Note: Power management modes are not supported for an APM operating system.

To reduce power consumption, the computer has two power management modes: screen blank and sleep (standby).

Screen blank state

If the time set on the “Turn off monitor” timer in the operating system expires, the LCD backlight turns off. You can also turn off the LCD backlight by pressing .

To end screen blank state and resume normal operation, press .

Putting the computer to sleep or shutting it down

When you have finished working with your computer, you can put it to sleep or shut it down.

Putting your computer to sleep

If you will be away from your computer briefly, put the computer to sleep.

When the computer is in sleep mode, you can quickly wake it to resume use, bypassing the startup process.

To put the computer to sleep, do one of the following:

• Close the display panel.

• Press the Power button.

• Open the charms and then select Settings → Power → Sleep.

Note: Put your computer to sleep before you move it. Moving your computer while the hard disk drive is spinning can damage the hard disk, causing loss of data.

To wake the computer, do one of the following:

• Press any key on the keyboard. (Notebook mode only)

• Press the Power button.

• Press the Windows button.

25

26


Shutting down the computer

If you are not going to use your computer for a long time, shut it down.

Open the charms, and then select Settings → Power → Shut down.

Lenovo Yoga 2 11

Lenovo Yoga 2 11

This chapter presents the following product-specific service references and product-specific parts information:

• “Specifications” on page 27

• “Status indicators” on page 29

• “Fn key combinations” on page 30

• “FRU replacement notices” on page 31

• “Removing and replacing an FRU” on page 32

• “Locations” on page 58

• “Parts list” on page 60

Specifications

The following table lists the specifications of the Lenovo Yoga 2 11:

Table 1. Specifications

Feature Description

Processor View the system properties of your computer.You can do this as follows: Open the Control Panel,and then select System and

Security → System.

Bus architecture • PCIe 2.0

DDR3L 1666MHz

HDMI 1.4

EDP 5.4G/2.7G

SATA 3.0

LPC 1.1

USB 2.0

USB 3.0

SMBus

HDA

SPI

I2C

Graphic Chipset • Intel Baytrail M

Display • 11.6-inch

Standard memory

CMOS

SSHD

Optical drive

I/O port

• DDR3L-1600MHz (max 4 GB)

• 256 bytes

• 500GB+8GB / 500GB+16GB

• NA

• Combo audio jack × 1

• Micro HDMI × 1

• USB 2.0 port × 1, USB 3.0 port × 1

• 2 in 1 card reader (SD/MMC)

27

28


Table 1. Specifications (continued)

Feature

Audio

Description

• 1/8" Stereo Headphone Output & Microphone input combo jack

• Integrated Speakers Stereo × 2

• Built-in microphone × 2

• 1 slot

PCI Express

Mini Card slot

Bluetooth wireless

Keyboard

Touch pad

Integrated camera

Battery

AC adapter

Pre-installed operating system

• Combined in combo card

• 6-Row, Lenovo Keyboard

• Multi-touch type

• 1.0 Mega or 720P HD

• 4 cells, 34 Wh

• 20 V, 45 W

• Win 8 64 bit, Windows 8.1(launch by wave,currently TTM w/ win8 64 bit)

Lenovo Yoga 2 11

Status indicators

The system status indicators below show the computer status:

1 2

Table 2. Status indicators

Indicator

Battery status indicator

Power status indicator

Indicator status Meaning

On (solid white)

Solid amber

The battery has more than 20% charge.

The battery has between 5% and

20% charge.

Fast blinking amber The battery has less than 5% charge.

Slow blinking amber

Slow blinking white

On (solid white)

Blinking

Off

The battery is being charged. When battery charge reaches 20%, the blinking color changes to white.

The battery has between 20% and

80% charge and is still charging.

When the battery reaches 80% charge the light will stop blinking, but charging will continue until the battery is fully charged.

The computer is powered on.

The computer is in sleep mode.

The computer is powered off.

29


Fn key combinations

The following table describes the functions of Fn key combinations.

Table 3. Function key combinations

: Mutes/unmutes the sound.

:

:

:

:

:

:

:

:

:

:

:

Decreases the volume level.

Increases the volume level.

Closes the currently active window.

Refreshes the desktop or the currently active window.

Enables/disables the touch pad.

Enables/disables Airplane mode.

Displays all currently active apps.

Turns on/off the backlight of the LCD screen.

Toggles the display between the computer and an external device.

Decreases display brightness.

Increases display brightness.

30

Lenovo Yoga 2 11

FRU replacement notices

This section presents notices related to removing and replacing parts. Read this section carefully before replacing any FRU.

Screw notices

Loose screws can cause a reliability problem. In the Lenovo computer, this problem is addressed with special nylon-coated screws that have the following characteristics:

• They maintain tight connections.

• They do not easily come loose, even with shock or vibration.

• They are harder to tighten.

Do the following when you service this machine:

• Keep the screw kit in your tool bag.

• Carefully remove screws for reuse when replacing FRUs.

• Use a torque screwdriver if you have one.

Tighten screws as follows:

• Plastic to plastic

Turn an additional 90° after the screw head touches the surface of the plastic part: more than 90°

(Cross-section)

• Logic card to plastic

Turn an additional 180° after the screw head touches the surface of the logic card: more than 180°

(Cross-section)

• Torque driver

If you have a torque screwdriver , refer to the “Torque” column for each step.

• Make sure that you use the correct screws. If you have a torque screwdriver, tighten all screws firmly to the torque shown in the table. Carefully remove screws for reuse when replacing FRUs. Make sure that all screws are tightened firmly.

• Ensure torque screwdrivers are calibrated correctly following country specifications.

31


Removing and replacing an FRU

This section presents exploded figures with the instructions to indicate how to remove and replace the FRU. Make sure to observe the following general rules:

1. Do not attempt to service any computer unless you have been trained and certified. An untrained person runs the risk of damaging parts.

2. Before replacing any FRU, review “FRU replacement notices” on page 31.

3. Begin by removing any FRUs that have to be removed before the failing

FRU. Any of such FRUs are listed at the top of the page. Remove them in the order in which they are listed.

4. Follow the correct sequence in the steps to remove the FRU, as given in the figures by the numbers in square callouts.

5. When turning a screw to replace an FRU, turn it in the direction as given by the arrow in the figure.

6. When removing the FRU, move it in the direction as given by the arrow in the figure.

7. To put the new FRU in place, reverse the removal procedures and follow any of the notes that pertain to replacement. For information about connecting and arranging internal cables, see “Locations” on page 58.

8. When replacing an FRU, use the correct screw as shown in the procedures.

DANGER

Before removing any FRU, turn off the computer, unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any of the interconnecting cables.

Attention: After replacing an FRU, do not turn on the computer until you have made sure that all screws, springs, and other small parts are in place and none are loose inside the computer. Verify this by shaking the computer gently and listening for rattling sounds. Metallic parts or metal flakes can cause electrical short circuits.

Attention: The system board is sensitive to, and can be damaged by, electrostatic discharge. Before touching it, establish personal grounding by touching a ground point with one hand or using an electrostatic discharge (ESD) strap (P/N 6405959) to remove potential shock reasons.

32

Lenovo Yoga 2 11

1010 Base cover

Figure 1. Removal steps of base cover

Remove the screws 1 . Then remove the base cover 2 .

1

1

1 1

2

1

1

1

1

1

1

Step Screw (quantity)

1

M2 × 6 mm, flat-head, nylok-coated

(10) Lower to Upper

Color Torque P/N

Silver 1.85+/-0.15 kgf*cm 90204957

33

34


Note: Applying labels to the base cover

The new base cover FRU is shipped with a kit containing labels of several kinds. When you replace the base cover, you need to apply the following labels: f g h i j

The following labels need to be peeled off from the old base cover and put on the new base cover. a b win8 OS label

Rating label(ww or China) c d e

Rating label print

India BIS label

KCC label

Indonesia D side label

BT WL label FOR US/CA/TW/BRAZIL/INDONESIA/ISRAEL label

SIRIM BT label

SIRIM WL label

BRAZIL BT or WL label

For some models, you also need to apply one or two FCC labels. Check the old base cover; if it has one or two FCC labels, find duplicates of them in the label kit and apply them to the new base cover.

For the location of each label, refer to the following figure: g h i f j d e a b c

Lenovo Yoga 2 11

1020 Battery pack

For access, remove this FRU:

• “1010 Base cover” on page 33

DANGER

Only use the battery specified in the parts list for your computer. Any other battery could ignite or explode.

Figure 2. Removal steps of battery pack

Unplug the battery connector 1 and remove the screws remove the battery pack in the direction shown by arrow

2

4 .

and screw 3 . Then

2

2

2

4

3

2

2

2

1


2

M2 × 3.5 mm, flat-head, nylok-coated

(6) Bty to Upper


(1) Bty to Upper

Color Torque

Black 1.85+/-0.15 kgf*cm

P/N

90204954


When installing: Make sure that the battery connector is attached firmly.

35

36


1030 Hard disk drive

For access, remove these FRUs in order:


• “1020 Battery pack” on page 35

Attention:

• Do not drop the hard disk drive or apply any physical shock to it. The hard disk drive is sensitive to physical shock. Improper handling can cause damages and permanent loss of data.

• Before removing the drive, suggest the customer to backup all the information on it if possible.

• Never remove the drive while the system is operating or is in suspend mode.

Figure 3. Removal steps of hard disk drive

Detach connector in the direction shown by arrow screws

1 . Remove the frame fixing

2

, then remove the hard disk drive in the direction shown by arrow

3

.

1

2

2

2

2 3


1

M2 × 3.5 mm, flat-head, nylok-coated (4)

HDD to Upper

Color Torque


Lenovo Yoga 2 11

Figure 3. Removal steps of hard disk drive (continued)

Remove four screws

4

and detach the metal frame from the hard disk drive.

4

4

4

4


1

M3.0 × 3.0 mm, flat-head, nylokcoated

(4) HDD to HDD BRKT


Silver 1.85+/-0.15 kgfcm 90204955

When installing: Make sure that the HDD connector is attached firmly.

37

38


1040 PCI Express Mini Card for wireless LAN




Figure 4. Removal steps of PCI Express Mini Card for wireless LAN

Disconnect the two wireless LAN cables (black, white) screw

1 , and then remove the

2 . Remove the card in the direction shown by arrow 3 .

2

3

1 1

In step 1 , unplug the jacks by using the removal tool antenna RF connector

(P/N: 08K7159), or pick up the connectors with your fingers and gently unplug them in the direction shown by the arrows.

Notes: The wireless LAN card has 2 cables in step 1 .

The wireless LAN card in some models might have 3 cables in step

1

.


2


WLAN to Upper

Color Torque


When installing:

When installing the wireless LAN card, plug the black cable into the jack labeled MAIN and the white cable into the jack labeled AUX.

Lenovo Yoga 2 11

1050 System board

Important notices for handling the system board:

When handling the system board, bear the following in mind.

• Be careful not to drop the system board on a bench top that has a hard surface, such as metal, wood, or composite.

• Avoid rough handling of any kind.

• During the whole process, make sure not to drop or stack the system board.

• If you put a system board down, make sure to put it only on a padded surface, such as an ESD mat or conductive corrugated material.




• “1030 Hard disk drive” on page 36

• “1040 PCI Express Mini Card for wireless LAN” on page 38

39

40


Figure 5. Removal steps of system board

Detach keyboard connector in the directions shown by arrows power board connector in the directions shown by arrows pad connector in the directions shown by arrows connectors in the direction shown by arrow direction shown by arrow shown by arrow screws K .

H

J

G

5 and 6

3

1

and

and

4

2 ,

, touch

, unplug speaker

, DC-IN cable connector in the

, disconnect camera connector in the direction

,LCD connector in the direction shown by arrow I . Remove

3

4

11

7

8

11

11

11

11

11

9

11

11

10

1

2

6

5 7

When installing: Make sure that all the connectors are attached firmly


5


MB to Upper

Color Torque


Lenovo Yoga 2 11

Figure 5. Removal steps of system board (continued)

Remove the system board in the direction shown by arrow L .

12

41

42


1060 Speakers






• “1050 System board” on page 39

Figure 6. Removal steps of speakers

Remove screws 1 . Lift the speakers in the direction shown by arrows 2 .

2

1

1 1

2

1


1

M2 × 2 mm, flat-head, nylok-coated

(4) speaker to Upper


Black 1.85+/-0.15 kgf*cm 90204952

When installing: Make sure that the connectors are attached firmly.

Lenovo Yoga 2 11

1070 LCD unit







Figure 7. Removal steps of LCD unit

Remove the screws 1 .

1 1

1 1


3


(6) Hinge to Upper


Silver 1.85+/-0.15 kgf*cm 90204956

43

44


Figure 7. Removal steps of LCD unit (continued)

Open the hinges 2 , then remove the upper case from the LCD unit in the direction shown by arrow 3 .

2

2

3

Lenovo Yoga 2 11

1080 Power board and power assembly







• “1070 LCD unit” on page 43

Figure 8. Removal steps of power board and power assembly

Remove the screw arrow

2

.

1 , then remove the power board in the direction shown by

2

1


1


Power board to Upper

Color Torque


Remove the power assembly in the direction shown by arrow 1 .

1

45

46


1090 LCD front cover







• “1060 Speakers” on page 42


• “1080 Power board and power assembly” on page 45

Figure 9. Removal steps of LCD front cover

Remove LCD bezel screw pad 1 and the screws 2 .

1

2

1

2


2


Hinge cover to LCD cover

Color Torque


Lenovo Yoga 2 11

Figure 9. Removal steps of LCD front cover (continued)

Remove the hinge cover in the direction shown by arrows 3 .

3

3

3

47

48


1100 Win8 home board, LCD cover, and hinges










• “1090 LCD front cover” on page 46

Figure 10. Removal steps of Win8 home board, LCD cover, and hinges

Remove the screw by arrow by arrow 3 .

1 then remove the Win8 home board in the direction shown

2 , disconnect the Win8 home board connector in the direction shown

1

2

3


2


Win8 home board to LCD cover

Color Torque


Lenovo Yoga 2 11


(continued)

Adjust the hinges in the direction shown by arrows rubbers 5 and pull out the cables.

4 . Then remove the hinge

4

4

5

Remove the screws arrows 7 .

6 , then remove the hinges in the directions shown by

6 6

7

7

6

6


8


Hinge to LCD cover

M2 × 2 mm, flat-head, nylok-coated (2) Hinge

BKT to LCD cover

M2 × 2.5 mm, flat-head, nylok-coated (2) Hinge

BKT to LCD cover

Color Torque

Silver 1.85+/-0.15 kgf*cm



49

50



(continued)

Remove screws by arrow 9 .

8 . and then remove the LCD module in the direction shown

8

9

8


6


(2) LCD module to LCD cover


Black 1.85+/-0.15 kgf*cm 90204950

Lenovo Yoga 2 11

1110 LCD module










• “1090 LCD front cover” on page 46

• “1100 Win8 home board, LCD cover, and hinges” on page 48

Figure 11. Removal steps of LCD module

Detach the connector in the directions shown by arrows remove the LCD cable.

1

and

2

. Then

2

1

51

52


Figure 11. Removal steps of LCD module (continued)

Remove the screw 3 . Lift the camera and the camera bracket slightly 4

Unplug the integrated camera connector in the direction shown by arrow

.

5 .

Remove the integrated camera bracket and integrated camera from the LCD module.

4

3

5


3

M1.6 × 2.5 mm, flat-head, nylok-coated (1)

Camera to LCD cover

Color Torque


Lenovo Yoga 2 11

Figure 11. Removal steps of LCD module (continued)

Remove screws arrow

1 then remove the sensor board in the direction shown by

2 , unplug the connector in the direction shown by arrow 3 .

1 2 1

3


2

M1.6 × 2.5 mm, flat-head, nylok-coated

(2) Sensor to LCD cover


Black 1.00+/-0.20 kgf*cm 90204951

53


Locations

Front view and right-side view

1 Integrated camera (on select models)

2 Multi-touch screen

3 Windows button

4

Built-in microphones

5 Wireless LAN antennas

6 Touch pad

7 Battery status indicator

Note: For the description of each indicator, see “Status indicators” on page 29.

8 Power button and power status indicator

9 Novo button

J Rotation lock button

K

Volume down button

L Volume up button

M Combo audio jack

N USB port

1

2

3

5

4

6

7

8

9 10

11 12

13

14

54

Bottom and Left-side view

1 Speakers

2

Micro HDMI port

3 Memory card slot

4 USB 3.0 port

5 AC power adapter jack

1

Lenovo Yoga 2 11

1

2

3

4

5

55


Parts list

This section presents the following service parts:

• “Overall” on page 61

• “LCD FRUs” on page 63

• “Keyboard” on page 65

• “Miscellaneous parts” on page 67

• “Screw” on page 67

• “AC adapters” on page 68

• “Power cords” on page 69

Notes:

• Each FRU is available for all types or models, unless specific types or models are specified.

56

Overall

1

2

4

7 b c a

6

5

11

3 d

8

9

10

12

11

13 e

14

Lenovo Yoga 2 11

57

58


Table 4. Parts list—Overall

No. FRU

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2 a-e See "Miscellaneous parts" on page 67.

1 LCD unit (see "LCD FRUs" on page 63.)

Vienna Upper Case SV W/KB-US

Vienna Upper Case SV W/KB-GK

Vienna Upper Case SV W/KB-INT'E US

Vienna Upper Case SV W/KB-KO

Vienna Upper Case SV W/KB-CH

Vienna Upper Case SV W/KB-RU

Vienna Upper Case SV W/KB-AR-E

Vienna Upper Case SV W/KB-HB

Vienna Upper Case SV W/KB-TI

Vienna Upper Case SV W/KB-INDIA

Vienna Upper Case SV W/KB-UK

Vienna Upper Case SV W/KB-IT

Vienna Upper Case SV W/KB-SP

Vienna Upper Case SV W/KB-TR

Vienna Upper Case SV W/KB-PO

Vienna Upper Case SV W/KB-LA

Vienna Upper Case SV W/KB-CF-E

Vienna Upper Case SV W/KB-ND

Vienna Upper Case SV W/KB-FR

Vienna Upper Case SV W/KB-GR

Vienna Upper Case SV W/KB-NL

Vienna Upper Case SV W/KB-HG

Vienna Upper Case SV W/KB-BE

Vienna Upper Case SV W/KB-ICE

Vienna Upper Case SV W/KB-SA

Vienna Upper Case SV W/KB-SW

Vienna Upper Case SV W/KB-BU

Vienna Upper Case SV W/KB-CZ-SK

Vienna Upper Case SV W/KB-BZ

Vienna Upper Case SV W/KB-JA

Vienna Upper Case BK W/KB-US

Vienna Upper Case BK W/KB-GK

Vienna Upper Case BK W/KB-INT'E US

Vienna Upper Case BK W/KB-KO

Vienna Upper Case BK W/KB-CH

Vienna Upper Case BK W/KB-RU

Vienna Upper Case BK W/KB-AR-E

Vienna Upper Case BK W/KB-HB

Vienna Upper Case BK W/KB-TI

Vienna Upper Case BK W/KB-INDIA

Vienna Upper Case BK W/KB-UK

Vienna Upper Case BK W/KB-IT

Vienna Upper Case BK W/KB-SP

Vienna Upper Case BK W/KB-TR

Vienna Upper Case BK W/KB-PO

Vienna Upper Case BK W/KB-LA

FRU no.

CRU ID.

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

90204974

90204975

90204976

90204977

90204978

90204979

90204980

90204981

90204982

90204983

90204984

90204985

90204986

90204987

90204988

90204989

90204958

90204959

90204960

90204961

90204962

90204963

90204964

90204965

90204966

90204967

90204968

90204969

90204970

90204971

90204972

90204973

90204990

90204991

90204992

90204993

90204994

90204995

90204996

90204997

90204998

90204999

90205000

90205001

90205002

90205003

Lenovo Yoga 2 11

Table 4. Parts list—Overall (continued)

4

4

4

4

5

6

4

4

4

4

4

4

4

4

4

4

3

4

3

3

2

2

2

2

2

2

2

2

2

2

2

2

2

2

No. FRU

6

6

6

6

6

6

FRU no.

Vienna Upper Case BK W/KB-CF-E

Vienna Upper Case BK W/KB-ND

Vienna Upper Case BK W/KB-FR

Vienna Upper Case BK W/KB-GR

Vienna Upper Case BK W/KB-NL

Vienna Upper Case BK W/KB-HG

Vienna Upper Case BK W/KB-BE

Vienna Upper Case BK W/KB-ICE

Vienna Upper Case BK W/KB-SA

Vienna Upper Case BK W/KB-SW

Vienna Upper Case BK W/KB-BU

Vienna Upper Case BK W/KB-CZ-SK

Vienna Upper Case BK W/KB-BZ

Vienna Upper Case BK W/KB-JA

Intel N3520 2G 2M 4cBGA CPU, N3520

Intel N2920 1.6G 2M 4cBGA CPU, N2920

Intel N2815 2G 1M 2cBGA CPU, N2815

Vienna MB N2815 2G

Vienna MB W8P N2815 2G

Vienna MB W8S N2815 2G

Vienna MB N3520 2G



Vienna MB N2920 2G



Vienna MB N3520 4G



Vienna MB N2920 4G



Vienna Thermal

H5TC4G63AFR-PBA(D/4Gb/29nm), 2G DDRIIIL1333

ONBOARD

MT41K256M16HA-125:E(V80A/4Gb/30nm), 2G

DDRIIIL1333 ONBOARD

K4B4G1646Q-HYK0(Q/4Gb/35nm), 2G DDRIIIL1333

ONBOARD

EDJ4216EFBG-GN-F(F/4Gb/30nm), 2G DDRIIIL1333

ONBOARD

H5TC4G63AFR-PBA(D/4Gb/29nm), 4G DDRIIIL1333

ONBOARD

MT41K256M16HA-125:E(V80A/4Gb/30nm), 4G

DDRIIIL1333 ONBOARD

K4B4G1646Q-HYK0(Q/4Gb/35nm), 4G DDRIIIL1333

ONBOARD

102500681

90005650

90005651

90005652

90005653

90005654

90005655

90005656

90005657

90005658

90005659

90204919

90005660

90005661

90005662

90005663

90204929

1100847

90205004

90205005

90205006

90205007

90205008

90205009

90205010

90205011

90205012

90205013

90205014

90205015

90205016

90205017

102500678

102500679

1100828

1100918

1100848

1100847

1100828

1100918

CRU ID.

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

59

60


Table 4. Parts list—Overall (continued)

No. FRU FRU no.

7

7

7

7

6

8

8

EDJ4216EFBG-GN-F(F/4Gb/30nm), 4G DDRIIIL1333

ONBOARD

ST500LT032 6G 5mm 500G HDD, 500G 5400RPM

WD5000MPCK-24AWHT0 6G 5mm 500G HDD, 500G

5400RPM

HYBRID 500G 5400RPM SSHD (8G)

WD5000M22K-24Z1LT0 MJ500Sh-2 16GB, HYBRID

500G 5400RPM SSHD (16G)

Cbt BCM943142HM 1x1BGN+BT4.0 HMC WLAN,

NON-INTEL 1X1 BGN+BT4.0

Liteon WB335 1x1BGN+BT4.0 HMC WLAN, NON-

INTEL 1X1 BGN+BT4.0

Vienna Power Board 9

10 Simplo battery 2S2P 7.4V 34Wh (ATL cell, 8.5Wh),

4CELL 34WH

10 LG battery 2S2P 7.4V 34Wh ( LG cell, 8.5Wh), 4CELL

34WH

11 Vienna Speaker R+L

12 Vienna DC-IN Cable

13 Vienna Antenna

14 Vienna Lower Case Orange

14 Vienna Lower Case SV

14 Vienna Lower Case BK

1100848

16200575

16200584

TBD

16200616

20200222

20200437

90005666

121500223

121500224

90204930

90204936

90204938

90204920

90204921

90204922

CRU ID.

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

Lenovo Yoga 2 11

LCD FRUs

In Lenovo Yoga 2 11, the type of LCD is 11.6-inch high definition (HD).

1

2

2

3

4

6

3

8

7

15

9

10

12

7

4

5

11

14

13

16

61

62


Table 5. Parts list—11.6-inch LCD FRUs

No. FRU FRU no. CRU ID.

4

5

5

6

1

1

2

3

Vienna LCD Module

Vienna LCD Module LG

Vienna Hinge R+L

Vienna Hinge Cap Rubber

Vienna LCD Bezel Screw PAD

Vienna LCD Bezel CAP

Vienna LCD Bezel CAP LG

Vienna WIN8 Home Board

7

8

Vienna MIC Rubber

Vienna Sensor Board

9 Vienna Camera Bracket

10 Vienna Camera

11 Vienna Panel control board Mylar

12 Vienna Camera Cable

13 Vienna LCD Cable

13 Vienna LCD Cable LG

14 Panel 11.6 HD LED MULTI-TOUCH AUO B116XAT02.0

5A HD G W LED1 NB LCD(T)

14 Panel 11.6 HD LED MULTI-TOUCH BOE

HN116WXA-100 HD G W NB LCD(T)

15 Vienna LCM Rubber

16 Vienna LCD Cover Orange

16 Vienna LCD Cover SV

16 Vienna LCD Cover BK

18201247

90204947

90204924

90204925

90204926

90400279

90400280

90204923

90204948

90204942

90204927

90204928

90005664

90204949

90005665

90204939

90005667

90204946

90204931

90204932

90204933

18201388

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

Lenovo Yoga 2 11

Keyboard

Table 6. Parts list—Keyboard

Language

Chicony KB

Darfon KB

English

U.K. English

Italian

Spanish

Turkish

Thai

Portuguese

Latin

Canadian Bilingual (En+Fr)

Korean

Traditional Chinese

Russian

French

German

Arabic

Brazilian

Japanese

Dutch

Greek

Hebrew

Hungarian

Nordic

Belgian

Icelandic

Slovenian

Swiss

US international

Bulgarian

Czech&Slovak

India

English

U.K. English

Italian

Spanish

Turkish

Thai

Portuguese

Latin


Korean

Traditional Chinese

Russian

French

German

Arabic

CRU ID.

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

P/N

25214403

25214404

25214405

25214406

25214407

25214409

25214408

25214410

25214440

25214441

25214442

25214443

25214444

25214445

25214446

25214447

25214448

25214449

25214450

25214451

25214452

25214453

25214454

25214381

25214382

25214383

25214384

25214385

25214386

25214387

25214388

25214389

25214390

25214391

25214392

25214393

25214394

25214395

25214396

25214397

25214398

25214399

25214400

25214401

25214402

63

64


Table 6. Parts list—Keyboard (continued)

Language

Darfon KB

(continued)

Sunrex KB

Brazilian

Japanese

Dutch

Greek

Hebrew

Hungarian

Nordic

Belgian

Icelandic

Slovenian

Swiss

US international

Bulgarian

Czech&Slovak

India

English

U.K. English

Italian

Spanish

Turkish

Thai

Portuguese

Latin


Korean

Traditional Chinese

Russian

French

German

Arabic

Brazilian

Dutch

Greek

Hebrew

Hungarian

Nordic

Belgian

Icelandic

Slovenian

Swiss

US international

Bulgarian

Czech&Slovak

India

CRU ID.

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

P/N

25214455

25214456

25214421

25214422

25214423

25214424

25214425

25214426

25214427

25214428

25214429

25214430

25214431

25214432

25214433

25214434

25214435

25214436

25214438

25214437

25214439

25214457

25214458

25214459

25214460

25214461

25214462

25214463

25214464

25214465

25214466

25214468

25214467

25214469

25214411

25214412

25214413

25214414

25214415

25214416

25214417

25214418

25214419

25214420

Lenovo Yoga 2 11

Miscellaneous parts

Table 7. Parts list—Miscellaneous parts

FRU

System miscellaneous parts:

• ( a) Vienna HDD AL Foil Mylar

• ( b) Vienna HDD Bracket

P/N

90204941

90204940

Cable miscellaneous parts:

• ( c) Vienna HDD Cable SEAGET

• ( c) Vienna HDD Cable WD

• ( d ) Vienna Power Board Cable

• ( e) Vienna TP Cable

Note: Italicized letters in parentheses are references to the exploded view in “Overall” on page 61.

90204934

90204935

90204937

90204945

CRU ID.

N

Screw

Table 8. Parts list—screws

FRU

Vienna SCREW M M 2.0D 2.5L K 4.5D 0.5T







Vienna SCREW M M 2D 6L K 3.5D 0.7T NI

P/N

90204950

90204951

90204952

90204953

90204954

90204955

90204956

90204957

CRU ID.

N

N

N

N

N

N

N

N

65

66


AC adapters

Table 9. Parts list—AC adapters

FRU

Adapter, BLACK 45W 3-PIN, Delta ADLX45NDC3A

20V2.25A adapter

Adapter, BLACK 45W 3-PIN, Liteon ADLX45NLC3A

20V2.25A adapter

Adapter, BLACK 45W 3-PIN, Chicony ADLX45NCC3A

20V2.25A adapter

P/N

36200245

CRU ID.

36200246

36200247

*

*

*

Lenovo Yoga 2 11

Power cords

A Lenovo power cord for a specific country or region is usually available only in that country or region:

Table 10. Parts list—2-pin power cords

Region

CCC

• LINETEK PC323+RVV300/300+LS15 1m

ARGENTINA

• LINETEK LS15+H03VV-F+LP39 1m

Danmark

• LINETEK LS15+H03VV-F+LP-38 1m

Switzerland


Brazil

• LINETEK LS15 H03VV-F LP26A 1m

Israel


UL

• LINETEK LP-30B + SPT-2 + LS15 1m

UK

• LINETEK LP-61L+ H03VV-F+ LS15 1m

Indian

• LINETEK PE-361+ H05VV-F+ LS15 1m

Italy

• LINETEK LS15+H03VV-F+PE-336 1m

Korea

• LINETEK LS15+H05VV-F+LP-E04A 1m

Australia

• LINETEK LS15+H03VV-F+LP-23A 1m

Taiwan

• LINETEK LS15+VCTF+LP-53 1m

Japan

• LINETEK LS15+VCTF+LP-54 1m

Africa

• LINETEK LS15+H03VV-F+PE-364 1m

CE

• LINETEK LP-34+H03VV-F + LS15 1m

CCC

• Longwell LSG-31+RVV300/300+LS-18 1m

Argentina

• Longwell LP-24+H03VV-F+LS-18 1m

Danmark


Switzerland


Brazil


P/N

145000600

145000599

145000598

145000597

145000596

145000595

145000594

145000593

145000592

145000591

145000590

145000589

145000588

145000587

145000586

145000585

145000568

145000567

145000566

145000565

145000564

CRU ID.

*

*

*

*

*

*

*

*

*

*

*

*

*

*

*

*

*

*

*

*

*

67

68


Table 10. Parts list—2-pin power cords (continued)

Region

Israel


UL

• Longwell LP-30B+SPT-2 18AWG+LS-18 1m

UK

• Longwell LP-61L+H03VV-F+LS-18 1m

Indian

• Longwell LP-67+BIS+LS-18 1m

Italy


Korea

• Longwell LP-486+KTLH03VV-F+LS-5 1m

Australia

• Longwell LP-23A+LFC-3R+LS-18 1m

Taiwan

• Longwell LP-71+VCTF+LS-33 1m

Japan

• Longwell LP-54+VCTF+LS-18 1m

Africa


CE

• Longwell LP-34A+H03VV-F+LS-18 1m

CCC

• VOLEX GB10S3+RVV 300/500+VAC5S 1m

UL

• Volex US15S3+SPT-2 +VAC5S 1m

Italy

• VOLEX IT10S3+H03VV-F+VAC5S 1m

Denmark

• VOLEX MP233D+H03VV-F+VAC5S 1m

Korea

• VOLEX M2511+KETI IEC+VAC5S 1m

Australia

• VOLEX AU10S3+H03VV-F+VAC5S 1m

Taiwan

• VOLEX TW15CS3+VCTF+VAC5S 1m

Japan

• VOLEX VAC5S+VCTF+M755 1m

Argentina

• VOLEX VA2073+H03VV-F+VAC5S 1m

Brazil

• VOLEX CH10S3+H03VV-F+VAC5S 1m

145000556

145000555

145000554

145000553

145000538

145000537

145000535

145000534

P/N

145000563

145000562

145000561

145000560

145000559

145000558

145000557

145000533

145000532

145000531

145000530

145000528

145000527

CRU ID.

*

*

*

*

*

*

*

*

*

*

*

*

*

*

*

*

*

*

*

*

*

Lenovo Yoga 2 11

Table 10. Parts list—2-pin power cords (continued)

Region

Israel

• VOLEX SI16S3+H03VV-F+VAC5S 1m

CE

• VOLEX M2511+H03VV-F+VAC5S 1m

Switzerland

• VOLEX MP232+H03VV-F+VAC5S 1m

UK

• VOLEX MP5004+H03VV-F+VAC5S 1m

P/N

145000526

145000525

145000524

145000605

CRU ID.

*

*

*

*

69

70


Table 11. Parts list—power cords

Region

UK

• lux 0031+H03VV-F 0.75/3C+0011 1m

Europe

• lux 0033+H03VV-F 0.75/3C+0011 1m

US

• lux 0014+SPT-2 60°C 18/3C+0016 1m

China

• lux 0036+RVV 300/300 0.75/3C+0002 1m

Indian

• lux 0046+IS694 0.75/3C+0011 1m

Japan

• lux 0018(E)+VCTF 0.75/3C+0021 1m

Australia

• lux 0038+H03VV-F 0.75/3C+0011 1m

Taiwan

• lux 0019+VCTF 0.75/3C+0021 1m

Korea

• lux 0033+H03VV-F 0.75/3C+0011 1m

Italy

• lux 0029+H03VV-F 0.75/3C+0011 1m

South Africa

• lux 0044+H03VV-F 0.75/3C+0011 1m

Brazil

• lux 0034+H03VV-F 0.75/3C+0011 1m

Israel

• lux 0041+H03VV-F 0.75/3C+0011 1m

Switzerland

• lux 0027+H03VV-F 0.75/3C+0011 1m

Denmark

• lux 0048+H03VV-F 0.75/3C+0011 1m

Argentina

• lux 0040+H03VV-F 0.75/3C+0011 1m

145500007

145500008

145500009

145500010

145500011

145500012

145500013

145500014

145500015

P/N

145500000

145500001

145500002

145500003

145500004

145500005

145500006

CRU ID.

*

*

*

*

*

*

*

*

*

*

*

*

*

*

*

*

Notices

Notices

Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any Lenovo intellectual property right may be used instead. However, it is the user’s responsibility to evaluate and verify the operation of any other product, program, or service.

Lenovo may have patents or pending patent applications covering subject matter described in this document. The furnishing of this document does not give you any license to these patents.

LENOVO GROUP LTD. PROVIDES THIS PUBLICATION “AS IS”

WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED,

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-

INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE. Some jurisdictions do not allow disclaimer of express or implied warranties in certain transactions, therefore, this statement may not apply to you.

This information could include technical inaccuracies or typographical errors.

Changes are periodically made to the information herein; these changes will be incorporated in new editions of the publication. Lenovo may make improvements and/or changes in the product(s) and/or the program(s) described in this publication at any time without notice.

The products described in this document are not intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. The information contained in this document does not affect or change Lenovo product specifications or warranties. Nothing in this document shall operate as an express or implied license or indemnity under the intellectual property rights of Lenovo or third parties. All information contained in this document was obtained in specific environments and is presented as an illustration. The result obtained in other operating environments may vary.

Lenovo may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you.

Any references in this publication to non-Lenovo Web sites are provided for convenience only and do not in any manner serve as an endorsement of those

Web sites. The materials at those Web sites are not part of the materials for this Lenovo product, and use of those Web sites is at your own risk.

71


Any performance data contained herein was determined in a controlled environment. Therefore, the result obtained in other operating environments may vary significantly. Some measurements may have been made on development-level systems and there is no guarantee that these measurements will be the same on generally available systems. Furthermore, some measurements may have been estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment.

Trademarks

The following terms are trademarks or registered trademarks of Lenovo in the

United States, other countries, or both.

Lenovo

OneKey

Microsoft and Windows are trademarks of Microsoft Corporation in the United

States, other countries, or both.

Other company, products, or service names may be trademarks or service marks of others.

72

No results