User manual | universal trip amplifier

PReasy
4131
UNIVERSAL TRIP AMPLIFIER
5
Input for RTD, TC, Ohm,
potentiometer, mA and V
2 adjustable alarm limits
FM-approved for installation in Div. 2
2 relay outputs
Universal AC or DC supply
Advanced features:
•Programmable via detachable display front
(4501), process calibration, relay simulation,
password protection, error diagnostics and
selection of help text in several languages.
Applications
Input signals:
Current
Volt- Potentio­
age
meter
Application:
•Process control with 2 pairs of potential-free
relay contacts which can be configured to suit
any application.
RTD and lin. R
Connect., wires
4
3
2
44
+
43
+
-
42
•Trip amplifier with window function defined by
a high and a low setpoint. The relay changes
state outside the window.
•Relay latch function, where the relay is
activated and can only be reset manually.
TC
41
Order separately for external CJC: 5910 CJC connector.
Output signals:
Relays
24
•Sophisticated sensor error surveillance, where
one relay holds the state immediately prior to
the sensor error, thus allowing the process to
continue. The other relay can be set for sensor
error alarm so that the defect sensor can be
replaced immediately.
23
22
21
Technical characteristics:
•When 4131 is used with the 4501 display /
programming front, all operational parameters
can be modified to suit any application. As
the 4131 is designed with electronic hardware
switches, it is not necessary to open the
module for setting of DIP switches.
•A green front LED indicates normal operation
and malfunction. A yellow LED is ON for each
active output relay.
Supply:
33
21.6...253 VAC
or
19.2...300 VDC
32
31
•Continuous check of vital stored data for
safety reasons.
• 3-port 2.3 kVAC galvanic isolation.
Lerbakken 10 · DK-8410 Rønde
Tlf. 8637 2677 · Fax 8637 3085
www.prelectronics.dk
Order codes:
4131 = Universal trip amplifier
4501 = Display / programming front
5910 = CJC connector
PR 4501 Display / programming front
Application:
Technical characteristics:
• Communications interface for modification of operational parameters in 4131.
• LCD display with 4 lines; Line 1 (H=5.57 mm) shows input
signal, line 2 (H=3.33 mm) shows units, line 3 (H=3.33 mm)
shows TAG no. and line 4 shows communication and relay
status.
• Can be moved from one 4131 module to
another and download
the configuration of the first trans­mitter to
subsequent transmitters.
• Fixed display for visualisation of process
data and status.
• Programming access can be blocked by assigning a password. The password is saved in the transmitter in order to
ensure a high degree of protection against unauthorised modifications to the configuration.
Mounting / installation:
• Click 4501 onto the front of 4131.
Electrical specifications:
Specifications range........................... -20°C to +60°C
Common specifications:
Supply voltage, universal................... 21.6...253 VAC, 50...60 Hz
or 19.2...300 VDC
Max. consumption.............................. ≤ 2.0 W
Fuse.................................................... 400 mA SB / 250 VAC
Isolation voltage, test / operation....... 2.3 kVAC / 250 VAC
Communications interface................. Programming front 4501
Signal / noise ratio.............................. Min. 60 dB (0...100 kHz)
Response time (0...90%, 100...10%):
Temperature input......................... ≤ 1 s
mA / V input................................... ≤ 400 ms
Calibration temperature...................... 20...28°C
Accuracy, the greater of the general and basic values:
General values
Input
type
All
Absolute
accuracy
Temperature
coefficient
≤ ±0.1% of span
≤ ±0.01% of span / °C
Basic values
Basic
accuracy
≤ ±4 µA
≤ ±20 µV
≤ ±0.2°C
≤ ±0.1 Ω
≤ ±0.1 Ω
Input
type
mA
Volt
Pt100
Linear resistance
Potentiometer
TC type:
E, J, K, L, N, T, U
TC type: R, S, W3,
W5, LR
TC type: B
85...400°C
TC type: B
400...1820°C
Temperature
coefficient
≤ ±0.4 µA / °C
≤ ±2 µV / °C
≤ ±0.01°C / °C
≤ ±0.01 Ω / °C
≤ ±0.01 Ω / °C
≤ ±1°C
≤ ±0.05°C / °C
≤ ±2°C
≤ ±0.2°C / °C
≤ ±4.5°C
≤ ±0.45°C / °C
≤ ±2°C
≤ ±0.2°C / °C
EMC immunity influence............................ < ±0.5% of span
Extended EMC immunity:
NAMUR NE 21, A criterion, burst............... < ±1% of span
Auxiliary supplies:
2-wire supply (terminal 44...43).......... 25...16 VDC / 0...20 mA
Max. wire size..................................... 1 x 2.5 mm2 stranded wire
Screw terminal torque........................ 0.5 Nm
Relative humidity................................ < 95% RH (non-cond.)
Dim., without display front (HxBxD)... 109 x 23.5 x 104 mm
Dimensions, w. display front (HxBxD).. 109 x 23.5 x 116 mm
Protection degree............................... IP20
Weight................................................ 170 g / 185 g with 4501
RTD, linear resistance and potentiometer input:
Input
type
Min.
value
Max.
value
Standard
Pt100
Ni100
Lin. R
Potentiometer
-200°C
-60°C
0Ω
10 Ω
+850°C
+250°C
10000 Ω
100 kΩ
IEC60751
DIN 43760
-
Input for RTD types:
Pt10, Pt20, Pt50, Pt100, Pt200, PT250, Pt300, Pt400, Pt500, Pt1000
Ni50, Ni100, Ni120, Ni1000
Cable resistance per wire (max.), RTD.. 50 Ω
Sensor current, RTD........................... Nom. 0.2 mA
Effect of sensor cable resistance
(3- / 4-wire), RTD................................ < 0.002 Ω / Ω
Sensor error detection, RTD............... Yes
Short circuit detection, RTD............... < 15 Ω
TC input:
Type
Min.
value
Max.
value
Standard
B
E
J
K
L
N
R
S
T
U
W3
W5
LR
0°C
-100°C
-100°C
-180°C
-200°C
-180°C
-50°C
-50°C
-200°C
-200°C
0°C
0°C
-200°C
+1820°C
+1000°C
+1200°C
+1372°C
+900°C
+1300°C
+1760°C
+1760°C
+400°C
+600°C
+2300°C
+2300°C
+800°C
IEC 60584-1
IEC 60584-1
IEC 60584-1
IEC 60584-1
DIN 43710
IEC 60584-1
IEC 60584-1
IEC 60584-1
IEC 60584-1
DIN 43710
ASTM E988-90
ASTM E988-90
GOST 3044-84
Cold junction compensation (CJC):
CJC via ext. sensor in connector 5910
(based on ambient temperature)... < ±1.0°C ±0.0°C/ °C
CJC via internal sensor
(based on temp. inside enclosure). < ±2.0°C ±0.2°C/ °C
Sensor error detection, all TC types... Yes
Sensor error current:
when detecting.............................. Nom. 2 μA
else................................................ 0 μA
Current input:
Measurement range........................... 0...20 mA
Programm. measurement ranges....... 0...20 and 4...20 mA
Input resistance.................................. Nom. 20 Ω + PTC 50 Ω
Voltage input:
Measurement range........................... 0...12 VDC
Programm. measurement ranges....... 0/0.2...1 ; 0/1...5 ; 0/2...10 V
Input resistance.................................. Nom. 10 MΩ
Relay outputs:
Relay functions................................... Setpoint, Window,
Sensor error, Latch
Power and Off
Hysteresis, in % / display counts....... 0.1...25% / 1...2999
On and Off delay................................ 0...3600 s
Max. voltage....................................... 250 VRMS
Max. current....................................... 2 A / AC or 1 A / DC
Max. AC power................................... 500 VA
Sensor error detection........................ Break / Make / Hold
Ex / I.S. approval:
FM, applicable in................................ Cl. I, Div. 2, Gr. A, B, C, D
Class I, Div. 2, Group IIC
Zone 2
Max. ambient temperature for T5....... 60°C
Marine approval:
Det Norske Veritas, Ships & Offshore.. Stand. f. Certific. No. 2.4
GOST R approval:
VNIIM, Cert. No.................................. www.prelectronics.com
Observed authority requirements: Standard:
EMC 2004/108/EC............................. EN 61326-1
LVD 2006/95/EC................................. EN 61010-1
FM...................................................... 3600, 3611, 3810 and
ISA 82.02.01
UL, Standard for Safety...................... UL 508
of span = of the currently selected measurement range
4131Y103-UK (0938)

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project