User manual | SP-4003

OPTICAL-ACOUSTIC
OUTDOOR SIREN
®
SP-4003
sp4003_e 06/06
The SP-4003 optical-acoustic outdoor siren is designed for burglary and panic alarm systems. The
signaling function is performed in two ways: optically (by blinking of LEDs situated on the housing
sides) and acoustically (with a modulated high-volume sound signal). The source of light are two
LED sets, while the sound signal is generated by means of a piezoelectric transducer. Design of the
siren ensures a high degree of tamper protection (against opening and/or pull-off from the mounting
surface). Electronic circuit of the device is made in SMD technology and impregnated against adverse
effect of weather conditions, thus ensuring a high reliability of the equipment. The outer housing of the
SP-4003 is made of PC LEXAN high-impact polycarbonate, so it features a very high mechanical
strength and guarantees esthetic look of the equipment even after many years of service. The inner
cover, made of galvanized sheet, provides extra protection for electronic components against
mechanical damage.
1. INSTALLATION
The SP-4003 outdoor siren should be mounted on a flat surface, at a place which is as hard to access
as possible, so as to minimize the risk of tampering. The device must be attached to the surface by
means of screws and expansion plugs. In order to take off the cover, remove the two locking screws
and lift it by an angle of approx. 60°. Be particularly careful when dismounting and remounting the
inner sheet metal cover.
NOTE:
Make sure there is a suitable distance (minimum 2.5 cm) between the upper edge of the
siren housing and the ceiling or another element which restricts the mounting position from
the above. Otherwise, replacement of the cover may be impossible.
mounting
holes
cable inlet
tamper element
MUST BE SCREWED DOWN
TO THE SURFACE!
Do not overtighten so as not to
break the narrowings
cover locking screws
Fig. 1. Housing of the outdoor siren
After installation of the outdoor siren mounting holes as well as the cable inlet should be sealed with
silicone compound.
2. CONNECTION
The SP-4003 outdoor siren can interface with any alarm signal source where in the event of alarm
condition 12V direct voltage appears on the alarm output(s). Connecting the 12V supply to the
terminals "+ SA –" will set off the acoustic alarm, and to the terminals "+ SO -" - the optical alarm.
It should be borne in mind that the current capacity of the control panel outputs must ensure proper
operation of the outdoor siren.
The tamper circuit protects the outdoor siren against removal of the outer housing and from being
detached from the wall. For the pull-off protection to function properly, the tamper element (Fig. 1)
must be screwed down to the mounting surface.
The "TMP" terminals are used to connect the device to the tamper circuit of the security system, while
the SENS.TMP terminals are provided for connecting the inner tamper contact of the housing.
JP1
JP2
JP3
JP4
JP5
JP1
JP2
JP3
JP4
JP5
signal 1
signal 2
JP1
JP2
JP3
JP4
JP5
- pins shorted
signal 3
- pins open
Fig. 2. Jumper settings to obtain required sound signal.
By setting jumpers on the pins JP1 – JP5 you can select one of the three sound signals for alarm
signaling.
ALARM CONTROL PANEL (example)
AC AC OUT1 COM OUT2 OUT3 COM +12V
R
RELAY
OUT1 - high current output, which triggers
the acoustic alarm signaling by direct
supply of +12V voltage to the +SA
terminal.
OUT2 - OC type low current output, which
triggers the optical alarm signaling
by supply of +12V voltage to the
+SO terminal via a relay
TO TAMPER CIRCUIT
+
SO
-
+ SA -
TMP TMP SENS.TMP
SP-4003 OUTDOOR SIREN
SO
SA
TMP
SENS.TMP
-
optical signaling
acoustic signaling
tamper circuit
tamper contact
Fig 3. Example of SP-4003 device connection to control panel outputs (high and low current)
Both kinds of signaling can be controlled from one control panel output if the terminals are connected
in parallel i.e. „+SA” with „+SO” and „-SA” with „-SO”.
Some control panels may require that a resistance R (approx. 1kΩ) be connected in the siren.
Otherwise, the device will be gently buzzing when switched off.
3. TECHNICAL DATA
Nominal supply voltage .....................................................................................................12V DC ±15%
Average current consumption during operation
optical signaling................................................................................................... 250mA
acoustic signaling................................................................................................ 200mA
Working temperature range...............................................................................................-35°C…+55°C
Sound intensity ................................................................................................................. approx. 120dB
Housing dimensions ....................................................................................................... 148x254x64mm
SATEL sp. z o.o.
80-172 Gdańsk
ul. Schuberta 79
POLAND
tel. + 48 58 320 94 00
[email protected]
www.satel.pl
Latest CE declaration of conformity
and certificates can be downloaded
from website www.satel.pl

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project