Lumel N43 User manual

PDF
Document
RAIL MOUNTED POWER NETWORK METER
N43
USER’S MANUAL
1
2
CONTENTS
1. APPLICATION.................................................................................. 5
2. METER SET ..................................................................................... 6
3. BASIC REQUIREMENTS, OPERATIONAL SAFETY ..................... 7
4. INSTALLATION ................................................................................ 8
5. METER DESCRIPTION ................................................................. 10
5.1 Current inputs .................................................................... 10
5.2 Voltage inputs .................................................................... 10
5.3 Connection diagramms ..................................................... 10
6. N43 PROGRAMMING .................................................................... 16
6.1 Front panel .......................................................................... 16
6.2 Power-on messages .......................................................... 18
6.3 Operating modes................................................................ 19
6.4 Measure mode .................................................................... 20
6.5 Parameter settings ............................................................. 25
6.5.1 Settings of meter parameters ........................................ 28
6.5.2 Settings of output parameters ....................................... 30
3
6.5.3 Settings of alarm parameters......................................... 31
6.5.4 Pages conﬁguration mode ............................................. 38
7. SOFTWARE UPGRADES .............................................................. 43
8. SERIAL INTERFACES................................................................... 46
8.1 RS-485 interface - list of parameters ................................ 46
8.2 USB interface - list of parameters .................................... 47
8.3 Examples of registers’ readout and write ........................ 48
8.4 Map of N43 meter registers ............................................... 54
9. ERROR CODES ............................................................................. 76
10. ACCESSORIES .......................................................................... 77
11. TECHNICAL DATA....................................................................... 78
12. ORDERING CODE ....................................................................... 85
4
1. APPLICATION
The N43 meter,assembled on a rail, is a programmable
digital instrument designed for the measurement of 3-phase,
3 or 4-wire power network parameters in balanced or unbalanced systems. The measured values are displayed on a dedicated
LCD display. The meter enables control and optimization of the
power electronic devices, systems and industrial installations.
The meter can be used for measuring: RMS of voltage and
current, active, reactive and apparent power, active and reactive
energy, power factors, frequency,THD and averaged values
P Demand - „power guard”, S Demand, I Demand /15, 30 or 60
minutes/. Voltages and currents are multiplied by given voltage and current ratios of the measuring transformers /for indirect
connections/. Power and energy indications take into account all
programmed ratio values. The value of each measured value can
be transmitted to the master system via the RS-485 interface.
Three relay outputs signal the overﬂow of the chosen quantity,
and the pulse output can be used for the consumption check
of 3-phase active energy.
5
There is a galvanic separation between following units of the
meter:
- supply,
- voltage and current inputs,
- RS-485,
- USB,
- pulse output OC,
- alarm outputs.
2. METER SET
Complete set of the meter includes:
- N43 Meter............................... 1 pc
- user’s manual ......................... 1 pc
- CD .......................................... 1 pc
6
3. BASIC REQUIREMENTS, OPERATIONAL
SAFETY
In terms of operational safety it meets the requirements
of the EN 61010-1 standard.
Comments concerning safety:
•
The meter should be installed and connected only by
a qualiﬁed personnel. All relevant safety measures should
be observed during installation.
•
Always check the connections before turning the meter on.
•
Prior to taking the meter housing off, always turn the supply
off and disconnect the measuring circuits.
•
Removal of the meter housing during the warranty period
voids the warranty.
•
This meter conforms to all requirements of the electromagnetic compatibility in the industrial environment.
•
The building installation should have a switch or a circuit-breaker installed. This switch should be located near
the device, easy accessible by the operator and suitably
marked.
7
4. INSTALLATION
The meter is designed for installation in modular distribution boards on a 35 mm rail. The meter housing is made
of plastic.
Housing dimensions: 105 x 110 x 60 mm. There are screw
terminal strips on the outer side of the meter which enable the
connection of external wires with diameter up to 5.3 mm2 /indirect measurement/ and up to 16 mm2 /direct measurement/.
The meters should not be installed on the rail in direct contact
with other devices that emit heat (e.g. other N43 meters).
There must be a minimum 5 mm spacing between devices
in order to enable heat transfer from a housing to the environment. Otherwise, the ambient temperature of a meter working
in direct contact with other devices can exceed the operating
temperature speciﬁed in rated operating conditions.
8
Fig. 1. Meter dimensions
9
5. METER DESCRIPTION
5.1 Current inputs
All current inputs are galvanically isolated (internal current
transformers). The meter is adapted for direct connections
/up to 63 A/ or to work with external measuring current transformers
/version 1 A/5 A /. Displayed current values and derivative quantities are automatically converted in relation to the introduced
external current transformer ratio.
5.2 Voltage inputs
Quantities on voltage inputs are automatically converted acc.
to the introduced ratio of the external voltage transformer. Voltage
inputs are speciﬁed in the order as either 3 x 57.7/100 V,
3 x 230/400 V or 3 x 290/500 V.
10
5.3 Connection diagrams
a) Meter connection diagrams in the 3-phase 4-wire network
Direct measurement in 4-wire network
11
12
Semi-indirect measurement in 4-wire network
13
Indirect measurement with the use of 3 current transformers and 2 or 3 voltage transformers in a 4-wire network
Semi-indirect measurement in a 3-wire network
b) Meter connection diagrams in the 3-phase 3-wire network
14
15
Fig 2. Meter connection diagrams in a network:
a) 3-phase 4-wire, b) 3-phase 3-wire
Direct measurement with the use of 2 current transformers and
2 or 3 voltage transformers in a 3-wire network
6. N43 PROGRAMMING
6.1 Front panel
Fig. 3. Front panel
16
Front panel description:
increase value button
and right displacement
active energy export
decrease value button
and left displacement
active energy import
conﬁrm button (ENTER)
symbol of energy /
reactive inductive power
USB socket
symbol of energy /
reactive capacity power
f1...f6
6 ﬁeld 3-digit displays for
readout and setting, ﬁelds f5
and f6 can create one 7-digit
ﬁeld
symbol of pulse output
*
units of the displayed values
symbols of alarms activation
indication
phase
kilo = 103
of
displayed
Mega = 106
17
6.2 Power-on messages
Fig. 4. Message after starting the meter
After switching the supply on, the meter performs a display test
and displays the N43 meter name, build and current software
as well as bootloader version.
where: n43 – meter type, 5A 230V – version
rEu revision
0.10 program version number
b0.00 bootloader version number
18
Switching
a supply on
Display of maximum,
minimum value
-erasing
Change
of displayed
pages
or
3 sec.
MEASURE mode
Erasing of alarm
latch
3 sec.
Enter a code
or
Code
Selection of Set
parameters
Meter parameters mode
Parameters acc. to Table 2
dEf=YES default settings
or
or
Change of quantity of
a selected parameter
or
means:
Output parameters mode
Parameters acc. to Table 3
dEf=YES default settings
or
or
Change of quantity of
a selected parameter
or
or
&gt;15 sec.
simultaneous pressure of the buttons
Alarm parameters mode
Parameters acc. to Table 4
dEf=YES default settings
or
Pages configuration mode
Selection of pages PAGn
dEf=YES default settings
or
Change of quantity of
a selected parameter
or
or
or
Fig. 5. N43 meter operating modes
6.3 Operating modes
Selection of parameter
on a page
or
19
6.4 MEASURE Mode
In Measure mode the values are displayed according
to the pages that are preset at the factory or conﬁgured by the
user in Pages Programming PAG.
Changing the page is done by pressing the
or
.
The sequence of displayed pages is according to a table created
in PAG mode.
Entry into monitoring of maximum and minimum values mode
occurs when pressing at the same time the buttons
and
for at least 3 seconds. Erasing maximum and minimum
values is done by pressing the button
while monitoring
their value.Alarms are active if they were allocated. Note that the
alarms do not need to be associated with quantities displayed
on the page because the change of a page would result in action
on two-state outputs.
Erasing alarm signalization latch / if it was set in the Alarm parameters mode Aln / is done by pressing the buttons
.
When reactive power or energy is displayed, this indication is
accompanied by a symbol of the inductive load
or capacity
load
.
When active energy is displayed, this indication is accompanied
by a symbol of
active energy export or
active
energy import.
20
Voltage [V]
Current [A]
Active power [W]
Reactive power [VAr]
Apparent power [VA]
Floating point
Active energy [Wh]
Reactive energy [VArh]
Apparent energy [VAh]
Fig 6. Formats of displayed values.
Exceeding of the upper or lower indication range is signaled
on the display by upper horizontal lines. For measurement of
the averaged values (P Demand, S Demand, I Demand) single
measurements are carried out with one second quantum,
however, visualized every 15 seconds. Averaging time to choose
from: 15, 30 or 60 minutes. After the meter is turned on or after
the averaged values are reset, the ﬁrst value will be calculated in
15 seconds after turning meter on or resetting. Until all samples
of the averaged values are acquired, the values are calculated
from already measured samples.
21
Current value in the neutral wire I(N) calculated from phase
current vectors is available in the registry 7544 of the serial
interface.
The alarm switching on is signaled by the lighting of the Aln
inscription (n= 1..3). The end of alarm duration at the alarm
signalization latch switched on, is indicated by the pulsation
of the Aln inscription (n= 1..3).
01 L1 phase voltage

(k)V
02 L1 phase wire current

(k)A
03 L1 phase active power
phase reactive
04 L1
power
L1
phase apparent
05 power
22
√
√
f1,f2,f3,f4,f5,f6
L1
√
x
f1
L1
√
√
f1
Signaling
Available
display ﬁelds

3Ph / 3W
quantity - blanked
00 no
display
3Ph / 4W
Table 1
Unit
Marking
Quantity
name
No. of par.
Selection of the monitored value:
P
(M,k)W
L1
√
x
f1
q
(M,k)VAr
L1
√
x
f1
S
(M,k)VA
L1
√
x
f1
phase active power
06 L1
factor (PF1=P1/S1)
factor of L1 phase
07 tgϕ
(tg1=Q1/P1)
P
PF
L1
√
x
f1

tg
L1
√
x
f1
08 L1 phase voltage THD
D
V%
L1
√
x
f1
09 L1 phase current THD
D
A%
L1
√
x
f1
10 L2 phase voltage

(k)V
L2
√
x
f2
11 L2 phase wire current

(k)A
L2
√
√
f2
12 L2 phase active power
P
L2
√
x
f2
13 L2 phase reactive power
q
(M,k)W
(M,k)VAr
L2
√
X
f2
14 L2 phase apparent power
S
(M,k)VA
L2
√
X
f2
phase active power
15 L2
factor (PF2=P2/S2)
P
PF
L2
√
X
f2
tg
L2
√
X
f2
X
X
f2
f2
factor of L2 phase 
16 tgϕ
(tg2=Q2/P2)
17 L2 phase voltage THD
D
18 L2 phase current THD
D
V%
A%
L2
L2
√
√
19 L3 phase voltage

(k)V
L3
√
X
f3
20 L3 phase wire current

(k)A
L3
√
√
f3
21 L3 phase active power
P
(M,k)W
L3
√
X
f3
22 L3 phase reactive power

(M,k)VAr
L3
√
X
f3
23 L3 phase apparent power
S
(M,k)VA
L3
√
X
f3
phase active power
24 L3
factor (PF3=P3/S3)
P
PF
L3
√
X
f3
23
factor of L3 phase 
25 tgϕ
(tg3=Q3/P3)
26 L3 phase voltage THD
D
27 L3 phase current THD
D
28 3-phase mean current*
29 3-phase active power
30 3-phase reactive power
31 3-phase apparent power
active power
32 3-phase
factor (PF=P/S)
factor 3 phases
33 tgϕ
mean (tg=Q/P)
34 Frequency
voltage
35 Phase-to-phase
L1-L2
Phase-to-phase
voltage
36 L2-L3
Phase-to-phase voltage
37
L3-L1
Mean phase-to-phase
38
voltage *
Active power averaged
39
(P Demand )*
Reactive power avera40
ged (S Demand )*
Current averaged
41
(I Demand) *
Active 3-phase input
42
energy
24
tg
L3
√
X
f3
V%
A%
L3
L3
√
√
X
X
f3
f3
S
P
q
(k)A
(M,k)W
(M,k)VAr
ΣL
ΣL
ΣL
√
√
√
√
√
√
f1,f2,f3,f4,f5
f1,f2,f3,f4,f6
f1,f2,f3,f4,f5
S
(M,k)VA
ΣL
√
√
f1,f2,f3,f4,f5
P
PF
ΣL
√
√
f1,f2,f3,f4

tg
ΣL
√
√
f1,f2,f3,f4

F
ΣL
√
√
f4

(k)V
L1 L2
√
√
f1

(k)V
L2 L3
√
√
f2

(k)V
L3 L1
√
√
f3

(k)V
ΣL
√
√
f1,f2,f3,f4,f5
P
(M,k)W
√
√
f4
S
(M,k)VA
ΣL
DM
ΣL
DM
√
√
f4

(k)A
ΣL
DM
√
√
f4
EnP
(M,k)Wh
ΣL
√
√
f5-f6
43
Active 3-phase output
energy
EnP
(M,k)Wh
44
Reactive 3-phase
inductive energy
En
(M,k)VArh
45
Reactive 3-phase
capacity energy
En
(M,k)VArh
46
3-phase apparent
energy
EnS
(M,k)VAh
47
Time – hours, minutes,
seconds
h
ΣL
√
√
f5-f6
ΣL
√
√
f5-f6
ΣL
√
√
f5-f6
ΣL
√
√
f5-f6
√
√
f5-f6
* available minimum and maximum values on the display and
interface registers
6.5 Parameter Settings
Fig 7. Setup menu
25
Programming mode is enabled by pressing and holding
button for about 3 seconds. To enable the programming user
must enter a correct access code. If there is no such a code or
after entering a correct code the program transits into the programming option. The message SEt (in the ﬁrst ﬁeld) and ﬁrst
parameter group PAr are displayed.
If the wrong access code is entered, only monitoring of the parameters is possible without possibility of changing them. Err cod
is displayed and then rE Ad Par.
Free eCon software can also be used for conﬁguration of the
N43 meters, it is available on the website www.lumel.com.pl.
26
Fig. 8. Programming matrix
27
6.5.1 Setting of Meter Parameters
Range
Notes/
description
Manufacturer
value
1 Access code entry
Marking
Parameter
name
Item
After entering the SEt procedure select with the button
or
mode Par and press
.
Buttons
set the requested values. The active position
is signaled by the cursor. The set value can be accepted by the
button
. Exit from the SEt procedure follows after pressing simultaneously the buttons
or waiting approx.
15 seconds.
Table 2
SE
0..30000
0 – no code
0
3PH-4
5A
2 Type of connection
n
3PH-4
3PH-3
3PH-4 – 3-phase,
4-wire
3PH-3 – 3-phase,
3-wire
3 Input current range
n
1A, 5A
or 63A
Input range: 1A or 5A
(for version In 1A/5A)
or 63A (for version
In 63A)
28
4
Current
ratio
transformer

1 .. 10000
1
5
Voltage
ratio
transformer

0,1…4000,0
1,0
Averaging time
/Demand integration
6
time/
Averaging synchro7 nization with the
real-time clock

sn
8
Energy counters
erasing
En
9
Erasing averaged
parameters

10 Default settings
t_15, t_30,
t_60
E
Averaging time of
active power
P Demand, apparent
power S Demand,
current I Demand
t_15, t_30, t_60
t_15
on/oFF
oFF
no – no activity,
En P – erase active
energy,
no,En P, En q, En q – erase reactive
energy,
En S,
En S – erase apparent
En ALL
energy,
En ALL – erase all
energies
no, YES
no
YES/no
no
reverting to default
(factory) group
settings Par
no
29
The automatic erasing of the energy is done with a change of
voltage or current ratio.
During the acceptation the value insertion possibility in the range
is checked. If the set value falls outside the allowable range, the
meter remains in parameter setting mode and the value is set to
the highest possible value (when entered value is too high) or
lowest possible value (when it is too low).
6.5.2 Setting of Output Parameters
Range
Notes/
description
Manufacturer
value
of impulses
1 Number
of OC output
MODBUS
2 Address Network
Designation
Parameter
name
Item
In the options, select the oUt mode and conﬁrm your choice
by pressing the button
.
Table 3
n
100 ..20000
number of impulses/
1kWh
1000

1…247
1
8n2
3 Transmission mode

4 Baud rate

5 Hour, minute

r8n2, r8E1,
r8o1, r8n1
4.8 k, 9.6 k,
19.2 k, 38.4 k
0,00.. 23,59
6 Default settings
E
no, yES
30
9.6 k
reverting to default (factory) group settings Par
00.00
n
Notes/
description
Manufacturer
value
2 Alarm type
Range
Quantity on the
alarm output
Designation
1
Parameter
name
Item
6.5.3 Setting of alarm parameters
In the options select the ALn mode and conﬁrm your choice by
pressing the button
Table 4
n
0..42
code as in Tab. 5

n-on, n-oFF,
on,oFF, H-on,
H-oFF,
AL1=U123
AL2=IS
AL3=P
Fig. 9
n-on
3
Lower value of
the input range

-144.0…144.0
in % of the rated
quantity value
90.0
4
Upper value of
the input range
n
-144.0…144.0
in % of the rated
quantity value
110.0
n
0 … 3600
in seconds
0
Time delay of the

switch off reaction
0 … 3600
in seconds
0
Time delay of
5 the switch on
reaction
6
31
7
8
Alarm re-activation lock
Alarm signalization latch

S
0 … 3600
in seconds
0
on, oFF
When alarm signalization latch function is
enabled and the alarm
state ends, alarm
symbol is not turned
off but begins to ﬂash.
Alarm symbol ﬂashes
until it is turned off by
pressing the buttons
oFF
(&gt; 3 sec). This function refers only to the
alarm signalization,
so the relay contacts
will operate without a
latch according to the
selected alarm type.
9 Default settings
32
E
no, yES
restoring default (factory) group settings
PAr
no
Entering the value Aon lower than AoF switches the alarm off.
a) n-on
Relay
enabled
b) n-oFF
c) On
33
d) OFF
Fig. 9. Alarm types: a)n-on, b) n-oFF, c) On, d) OFF.
Remaining types of the alarm:
•
H-on – always enabled;
•
H-oFF – always disabled.
Example no 1 of alarm setting:
Set alarm n-on type for monitored quantity P – 3-phase active
power,
Version: 5 A; 3 x 230/400 V. Setting the alarm on after exceeding
3800 W, switching the alarm off after power drops to 3100 W.
Calculations: rated 3-phase active power: P = 3 x 230 V x 5 A
= 3450 W
3450 W – 100 %
3450 W – 100 %
3800 W – Aon %
3100 W – AoF %
In conclusion:
Aon = 110.0 %
AoF = 90.0 %
Set: Monitored quantity: P; Alarm type: n-on, Aon 110.0,
AoF 90.0.
34
Selection of quantities on the alarm outputs:
Table 5
Item/
value
in the
register
4014,
4022,
4030
Displayed
element
00
oFF
no quantity /alarm disabled/
01
U_1
L1 phase voltage
Un [V] *
02
I_1
L1 phase wire current
In [A] *
03
P_1
L1 phase active power
Un x In x cos(0&deg;) [W] *
04
q_1
L1 phase reactive power
Un x In x sin(90&deg;) [VAr] *
05
S_1
L1 phase apparent power
Un x In [VA] *
06
PF1
L1 phase power factor (PF)
tg1
tgϕ factor of L1 phase
07
Quantity type
Value needed for calculations of percentage of the
alarm values (100 %)
none
1
1
08
THDU1 L1 phase voltage THD
100,00%
09
THDI1 L1 phase current THD
100,00%
35
10
U_2
L2 phase voltage
Un [V] *
11
I_2
L2 phase wire current
In [A] *
12
P_2
L2 phase active power
Un x In x cos(0&deg;) [W] *
13
q_2
L2 phase reactive power
Un x In x sin(90&deg;) [VAr] *
14
S_2
L2 phase apparent power
Un x In [VA] *
15
PF2
L2 phase power factor (PF)
1
16
tg2
tgϕ factor of L2 phase
1
17
THDU2 L2 phase voltage THD
100.00%
18
THDI2 L2 phase current THD
100.00%
19
U_3
L3 phase voltage
Un [V] *
20
I_3
L3 phase wire current
In [A] *
21
P_3
L3 phase active power
Un x In x cos(0&deg;) [W] *
22
q_3
L3 phase reactive power
Un x In x sin(90&deg;) [VAr] *
23
S_3
L3 phase apparent power
Un x In [VA] *
24
PF3
L3 phase power factor (PF)
1
25
tg3
tgϕ factor of L3 phase
1
26
36
THDU3 L3 phase voltage THD
100.00%
27
THDI3 L3 phase current THD
100.00%
28
U_A
mean 3-phase voltage
Un [V] *
29
I_A
mean 3-phase current
In [A] *
30
P
31
q
3-phase active power
(P1+P2+P3)
3-phase reactive power
(Q1+Q2+Q3)
3-phase apparent power
(S1+S2+S3)
3 x Un x In x cos(0&deg;) [W] *
3 x Un x In x sin(90&deg;)
[VAr] *
32
S
33
PF_A
3-phase power factor (PF)
1
34
tg_A
tgϕ factor of 3 phases
1
35
FrEq
frequency
36
U12
phase-to-phase voltage L1-L2
√3 Un [V] *
37
U23
phase-to-phase voltage L2-L3
√3 Un [V] *
38
U31
phase-to-phase voltage L3-L1
√3 Un [V] *
39
U123
mean phase-to-phase voltage
√3 Un [V] *
40
Pdt
41
Sdt
42
Idt
active power averaged
(P Demand )*
reactive power averaged
(S Demand )*
3x Un x In [VA] *
100 [Hz]
3 x Un x In x cos(0&deg;) [W] *
current averaged (I Demand) *
3 x Un x In [VA] *
In [A] *
* Un, In - rated values of voltages and currents
37
6.5.4 Pages conﬁguration mode
For the meter 1...12 user pages can be programmed or selected from 12
manufacturer’s default pages. The monitored values are shown in Table 1.
In the options, select the PAG mode and conﬁrm your choice
by pressing the button
.
Buttons
allow to select the page number to edit,
to accept press the button
. Buttons
allow
to select the conﬁg mode, to accept press the button
.
The cursor (blinking ---) will move to the ﬁrst ﬁeld f1. Buttons
allow to select the ﬁelds f1-f6. Conﬁrm a ﬁeld
selection by pressing the button
. Selection of the
monitored value in a selected ﬁeld can be done by pressing
the buttons
and conﬁrmed by pressing the button
.
After setting required quantities in the ﬁelds f1-f6 make, conﬁrm
it and save the pages with the selected quantities by pressing for
(approx. 3 sec.) the button
.
Fig.10 A display in pages conﬁguration mode.
38
Item
Pages programming
Parameter Designame
nation
Table 6
Range
Notes/description
Manufacturer
value
1
Display
panel illumination
lgt
oFF,1…60, on
oFF – off, on – on,
1..60 – illumination time
(in seconds) from pressing
the button
on
2
Page 1
P
oFF, on,
conﬁg
oFF– disabled,
on – enabled,
conﬁg – editing a selected
page
on
3
Page 2
P
oFF, on,
conﬁg
4
Page 3
P
oFF, on,
conﬁg
5
Page 4
P
oFF, on,
conﬁg
oFF– disabled,
on – enabled,
conﬁg – editing a selected
page
oFF– disabled,
on – enabled,
conﬁg – editing a selected
page
oFF– disabled,
on – enabled,
conﬁg – editing a selected
page
on
on
on
39
6
Page 5
P
oFF, on,
conﬁg
7
Page 6
P
oFF, on,
conﬁg
8
Page 7
P
oFF, on,
conﬁg
9
Page 8
P
oFF, on,
conﬁg
10
Page 9
P
oFF, on,
conﬁg
11
Page 10
P
oFF, on,
conﬁg
12
Page 11
P
oFF, on,
conﬁg
13
Page 12
P
oFF, on,
conﬁg
40
oFF– disabled,
on – enabled,
conﬁg – editing a selected
page
oFF– disabled,
on – enabled,
conﬁg – editing a selected
page
oFF– disabled,
on – enabled,
conﬁg – editing a selected
page
oFF– disabled,
on – enabled,
conﬁg – editing a selected
page
oFF– disabled,
on – enabled,
conﬁg – editing a selected
page
oFF– disabled,
on – enabled,
conﬁg – editing a selected
page
oFF– disabled,
on – enabled,
conﬁg – editing a selected
page
oFF– disabled,
on – enabled,
conﬁg – editing a selected
page
on
on
on
on
on
on
on
on
Manufacturer settings are shown below:
P02
P01
 V
 V
 V
 V
 V
 V

q VAr
PW
 V
q VAr
PW
i A
i A
i A
P W
P W
P W
iS A
q VAr
PW
P
q VAr
PW
q VAr
P VAr
P VAr
S VA
S VA
s VA

q VAr
PW
 VA
P04
P03
P06
P05
EnS kVAh
P08
P07
P

P
P



EnP kWh
EnP kWh

P10
P09
D %

h %
h %
En kVArh
hi %
PDm W
hi %
hi
En kVArh
41
P12
P11
P W
SDM VA
q VAr
EnP kWh
S VA
P W
iDM A
q VAr
q VA
hh.mm.ss
Visualization of the manufacturer’s page P02:
Fig.11 Visualization of the manufacturer’s page P02
42
7. SOFTWARE UPGRADE
A feature implemented in the N43 meters enables
to upgrade ﬁrmware using a PC with eCon software installed.
Free eCon software and the update ﬁles are available at
www.lumel.com.pl. Updating can be done directly via USB
or RS485 interface using RS485 to USB converter, e.g.: PD10
converter.
a)
b)
Fig. 12. Program window view:
a) eCon, b) software updates
43
Caution! Software update automatically resets meter settings
to manufacturer settings, so it is recommended to save meter
settings using eCon software before upgrading.
After launching eCon software, set in the settings required serial
port, baud rate, mode and address of the meter. Next, select
the N43 meter and click Conﬁg. Click the down arrow icon to
read all of the settings then the disk icon to save the settings to
a ﬁle (required to restore the settings later). After selecting the
option Update ﬁrmware (in the upper right corner of the screen)
the window Lumel Updater will be opened (LU) – Fig. 12 b.
press Connect. The Messages information window displays
information concerning upgrade process. If the port is opened
correctly, a Port opened message appears. Upgrade mode may
be entered using either of the two methods: remotely via LU
(using eCon settings – address, mode, baud rate, COM port)
and by turning a meter on while pressing the button
(while
entering bootloader mode using a button, an update is done
via USB interface only – baud rate 9600, RTU8N2, address 1).
The display will show the bootloader version, while the LU program displays the message Device found and the name and
version of the connected device. Click the ... button and browse
to the meter upgrade ﬁle. If the ﬁle is opened correctly, a File
44
opened message is displayed. Press the Send button. When
upgrade is successfully completed, the meter begins normal
operation while the information window displays Done message
and upgrade elapsed time. The next update can only be done
via a USB interface in case of a failed upgrade. After the LU
window is closed, go to parameter group Restoring manufacturer settings, select the option and press the button Apply.
Then press the folder icon to open a previously saved settings
ﬁle and press the up arrow icon to save the settings in the meter.
Current software version can be checked by reading the welcome message when switching the meter on.
Caution! Turning meter supply off during upgrade process may
result in permanent damage!
45
8. SERIAL INTERFACES
8.1 RS-485 INTERFACE – list of parameters
The implemented protocol is compliant with the PI-MBUS-300
Rev G speciﬁcation of Modicon. List of N43 meter serial interface
parameters:
•
identiﬁer
0xCF
•
meter address
1..247
•
baud rate
4.8, 9.6, 19.2, 38.4 kbit/s,
•
operating mode
Modbus RTU,
•
transmission mode
8N2, 8E1, 8O1, 8N1,
•
max. response time
600 ms.
•
max. no. of registers read in a single query
- 41 4-byte registers,
- 82 2-byte registers,
•
implemented functions
03, 04, 06, 16, 17,
- 03, 04 register readout,
- 06 single register writing,
- 16 writing of n registers,
- 17 device identiﬁcation.
Manufacturer’s settings: address 1, baud rate 9.6 kbit/s,
mode RTU 8N2,
46
8.2 USB INTERFACE – list of parameters
USB interface is dedicated only to the conﬁguration of meter
parameters.
•
identiﬁer
0xCF
•
meter address
1
•
baud rate
9.6 kbit/s,
•
operating mode
Modbus RTU,
•
transmission mode
8N2
•
max. response time
800 ms.
•
max. no. of registers read in a single query
- 41 4-byte registers,
- 82 2-byte registers,
•
implemented functions
03, 04, 06, 16, 17,
- 03, 04 register readout,
- 06 single register writing,
- 16 writing of n registers,
- 17 device identiﬁcation.
47
8.3 Examples of registers’ readout and write
Readout of n-registers (code 03h)
Example 1. Readout of two 16-bit integer registers, starting with
the register address 0FA0h (4000) - register values 10, 100.
Request:
Device
address
Function
01
03
Register address
Number of registers
B1
B0
B1
B0
CRC
checksum
0F
A0
00
02
C7 3D
Device
address
Funcion
Number
of bytes
Response:
01
03
04
48
Value from the
register
0FA0 (4000)
Value from the
register
0FA1 (4001)
B1
B0
B1
B0
00
0A
00
64
CRC
checksum
E4 6F
Example 2. Readout of two 32-bit ﬂoat registers as a combination
of two 16-bit registers, starting with the register address 1B58h (7000)
- register values 10, 100.
Request:
Device
address
Function
01
03
Register
address
Number
of registers
B1
B0
B1
B0
CRC
chcecksum
1B
58
00
04
C3 3E
Function
01
03
Number
of bytes
Device address
Response:
08
Value
from the
register
1B58
(7000)
Value
from the
register
1B59
(7001)
Value
from the
register
1B5A
(7002)
Value
from the
register
1B5B
(7003)
B3
B2
B1
B0
B3
B2
B1
B0
41
20
00
00
42
C8
00
00
CRC
chcecksum
E4 6F
49
Example 3. Readout of two 32-bit ﬂoat registers as a combination of two
16-bit registers, starting with the register address 1770h (6000) - register
values 10, 100.
Request:
Device
address
Function
01
03
Register
address
Number
of registers
B1
B0
B1
B0
CRC
chcecksum
17
70
00
04
4066
01
50
03
Number
of bytes
Function
Device
address
Response:
08
Value
from the
register
1770h
(6000)
Value
from the
register
1770h
(6000)
Value
from the
register
1772h
(6002)
Value
from the
register
1772h
(6002)
B1
B0
B3
B2
B1
B0
B3
B2
00
00
41
20
00
00
42
C8
CRC
chcecksum
E4 6F
Example 4. Readout of two 32-bit ﬂoat registers, starting with the register address 1D4Ch (7500) - register values 10, 100.
Request:
Device
address
Function
01
03
Register
address
Number
of registers
B1
B0
B1
B0
CRC
chcecksum
1D
4C
00
02
03 B0
Device
address
Function
Number
of bytes
Response:
01
03
08
Value from the
register
1D4D (7501)
Value from the register
1D4C (7500)
B3
B2
B1
B0
B3
B2
B1
B0
CRC
chcecksum
41
20
00
00
42
C8
00
00
E4 6F
Example 5. Writing the value 543 (0x021F) to the register 4000
(0x0FA0)
Request:
Device
address
Function
01
06
Register
address
Number
of registers
B1
B0
B1
B0
CRC
chcecksum
0F
A0
02
1F
CA 54
51
Response:
Device
address
Function
01
06
Register
address
Number
of registers
B1
B0
B1
B0
CRC
chcecksum
0F
A0
02
1F
CA 54
B0
14
07
D0
Number of bytes
B1
Number of
registers Lo
B0
No. of registers Hi
10
Value
for the
registers
0FA4
(4004)
Adrdess reg.Lo
Function
01
Value
for the
registers
0FA3
(4003)
Address reg.Hi
Device address
Writing to n-registers (code 10h)
Example 6. Writing two registers starting with the register address
0FA3h (4003). Writing the values 20, 2000.
Request:
B1
0F
A3
00
02
04
00
CRC
chcecksum
BB 9A
Response:
Device
address
Function
01
10
52
Register
address
Number
of registers
B1
B0
B1
B0
CRC
chcecksum
0F
A3
00
02
B2 FE
Device identiﬁcation report (code 11h)
Example 7. Device identiﬁcation.
Request:
Device
address
Function
CRC
chcecksum
01
11
C0 2C
Device address
Function
Number of bytes
Identiﬁer
Device status
Response:
01
11
19
CF
FF
Information ﬁeld of the device
software version (e.g. „-1.00
b-1.06” - N43 device with
software version 1.00 and
bootloader version 1.06)
4E 34 33 20 2D 31 2E 30 30 20
20 20 20 20 20 20 62 2D 31 2E
30 36 20
CRC
chcecksum
E0 24
53
8.4 Map of N43 meter registers
In the N43 meter, data are placed in 16 and 32-bit
registers. Process variables and meter parameters are placed
in the address area of registers in a way depended on the
variable value type. Bits in 16-bit registers are numbered from
the youngest to the oldest (b0-b15). 32-bit registers include
numbers of ﬂoat type in IEEE-754 standard. Sequence of 3210
bytes – the oldest is transmitted as the ﬁrst.
Table 7
Address
range
Value type
Description
4000
– 4066
Integer
(16 bits)
Value set in the 16-bit register. Registers
for meter conﬁguration. Register description
is presented in Table 6. Write and readout
registers.
4300
- 4386
Integer
(16 bits)
Value set in the 16-bit register. Registers
for displayed pages conﬁguration. Register
description is presented in Table 7. Write and
readout registers.
6000
– 6129
Float
(2x16 bits)
Value is set in the two following 16-bit registers. These registers contain the same data
as 32-bit registers from 7500 – 7564 range.
Readout registers. Bit sequence (1-0-3-2).
54
7000
– 7129
Float
(2x16 bits)
Value is set in the two following 16-bit registers. These registers contain the same data
as 32-bit registers from 7500 – 7564 range.
Readout registers. Bit sequence (3-2-1-0)
7500
– 7564
Float
(32 bits)
Value set in the 32-bit register. Register
description is presented in Table 8. Readout
registers.
Operations
Range
4000
RW
0…30000
Protection - password
0
4001
RW
0
reserved
0
4002
RW
0
reserved
0
Type of connection
0 - 3Ph/4W
1 - 3Ph/3W
0
4003
RW
0 .. 1
Default
Register
address
Description
Table 8
55
Input range: 1 A or 5 A:
0 - 1 A, 1 - 5 A (for version In
1A/5A);
63A: 0 – 63A, 1 -63A (for
version In 63A);
1
4004
RW
0,1
4005
RW
1...10000
Current transformer ratio
1
4006
RW
1...40000
Voltage transformer ratio *10
10
RW
0...2
Averaging time of active
power, apparent power and
current
0 – 15, 1- 30, 2- 60 minutes
0
4007
1
0.1
Synchronization with real-time
clock:
0 - no synchronization
1 - synchronization with clock
4008
RW
4009
RW
reserved
RW
Energy counters erasing
0 – no changes, 1- erase
active energies, 2 – erase
reactive energies, 3 – erase
apparent energies, 4 – erase
all energies
4010
56
0…4
0
4011
RW
0.1
Erasing averaged parameters
P Demand, S Demand,
I Demand
0
4012
RW
0.1
Min, max erasing
0
4013
RW
0.1
Erasing alarm signalization
latch
0
4014
RW
0.1..42
Alarm output 1 - value on output (code as in Table 5)
38
4015
RW
0...5
Alarm output 1 - type:
0 – n-on, 1– n-oFF, 2 – on,
3 – oFF, 4 – H-on, 5 – H-oFF
0
4016
RW
-1440..0..1440 [o/oo]
Alarm output 1 - lower value of
the alarm switch of the rated
input range
900
4017
RW
-1440..0..1440 [o/oo]
Alarm output 1 - upper value
of the alarm switch of the rated
input range
1100
4018
RW
3600 s
Alarm output 1 - activation
delay
0
4019
RW
3600 s
Alarm output 1 - alarm deactivation delay
0
4020
RW
3600 s
Alarm output 1 - re-activation
lock
0
57
4021
RW
0,1
Alarm 1 signalization latch
0
4022
RW
0.1..42
Alarm output 2 - value on output (code as in Table 5)
28
4023
RW
0..5
Alarm output 2 - type:
0 – n-on, 1– n-oFF, 2 – on,
3 – oFF, 4 – H-on, 5 – H-oFF
0
4024
RW
-1440..0..1440 [o/oo]
Alarm output 2 - lower value of
the alarm switch of the rated
input range
900
4025
RW
-1440..0..1440 [o/oo]
Alarm output 2 - upper value
of the alarm switch of the rated
input range
1100
4026
RW
3600 s
Alarm output 2 - activation
delay
0
4027
RW
3600 s
Alarm output 2 - alarm deactivation delay
0
4028
RW
3600 s
Alarm output 2 - re-activation
lock
0
4029
RW
0,1
4030
58
RW
0.1..42
Alarm 2 signalization latch
0
Alarm output 3 - value on output (code as in Table 5)
29
4031
RW
0..5
Alarm output 3 - type: 0 – n-on,
1– n-oFF, 2 – on, 3 – oFF,
4 – H-on, 5 – H-oFF
0
4032
RW
-1440..0..1440[o/oo]
Alarm output 3 - lower value of
the alarm switch of the rated
input range
900
4033
RW
-1440..0..1440
[o/oo]
Alarm output 3 - upper value
of the alarm switch of the rated
input range
1100
4034
RW
3600 s
Alarm output 3 - activation
delay
0
4035
RW
3600 s
Alarm output 3 - alarm deactivation delay
0
4036
RW
3600 s
Alarm output 3 - re-activation
lock
0
4037
RW
0.1
Alarm 3 signalization latch
0
4038
RW
100…20000
4039
RW
1..247
MODBUS Network Address
1
0
1
No. of impulses for the impulse
output
4040
RW
0..3
Transmission mode: 0-&gt;8n2,
1-&gt;8e1, 2-&gt;8o1, 3-&gt;8n1
4041
RW
0..3
Baud rate: 0-&gt;4800, 1-&gt;9600,
2-&gt;19200, 3-&gt;38400
1000
59
4042
RW
0,1
Upgrade change of transmission parameters
0
RW
0,1
Standard parameters save
(complete with resetting energy as well as min, max and
mean power to 0)
0
4043
4044
RW
reserved
-
4045
RW
Hour *100 + Minutes
0
4046
RW
reserved
-
4047
RW
0...2359
reserved
0
4048
R
0..152
Consumed active energy,
two older bytes
4049
R
0..65535
Consumed active energy,
two younger bytes
0
4050
R
0..152
Released active energy,
two older bytes
0
4051
R
0..65535
Released active energy,
two younger bytes
0
4052
R
0..152
Reactive inductive energy,
two older bytes
0
4053
R
0..65535
Reactive inductive energy,
two younger bytes
0
60
4054
R
0..152
Reactive capacity energy,
two older bytes
0
4055
R
0..65535
Reactive capacity energy,
two younger bytes
0
4056
R
0..152
Apparent energy, two older
bytes
0
4057
R
0..65535
Apparent energy, two younger
bytes
0
4058
R
0..65535
Status Register 1 – see description below
0
4059
R
0..65535
Status Register 2 – see description below
0
4060
R
reserved
0
4061
R
0..65535
Serial number two older bytes
-
4062
R
0..65535
Serial number two younger
bytes
4063
R
0..65535
Software version (*100)
-
4064
R
reserved
0
4065
R
reserved
0
4066
R
reserved
0
61
Energy is made available in hundreds of watt-hours (var-hours)
in double 16-bit register, and for this reason, one must divide
them by 10 when calculating values of particular energy from
registers, e.g.:
Consumed active energy = (reg. value 4038 x 65536 +
reg. value 4039) / 10 [kWh]
Released active energy = (reg. value 4040 x 65536 +
reg. value 4041) / 10 [kWh]
Reactive inductive energy = (reg. value 4042 x 65536 +
reg. value 4043) / 10 [kVarh]
Reactive capacity energy = (reg. value 4044 x 65536 +
reg. value 4045) / 10 [kVarh]
Status register of a device (address 4058, R):
Bit 15 – „1” – non-volatile memory damage
Bit 14 – „1” – no calibration or calibration error
Bit 13 – „1” – parameters value error
Bit 12 – „1” – energy value error
Bit 11 – „1” – phase sequence error
Bit 10 – „0” – current range 1 / 5 A~
„1” – current range 63 A~
62
Bit 9
0
0
1
1
Bit 8
0
1
0
1
voltage range
57.7 V~
230 V~
290 V~
reserved
Bit 7 – „1” – averaging interval has not ended
Bit 6 – „1” – frequency for THD calculation outside ranges:
48 – 52 for 50 Hz,
58 – 62 for 60 Hz
Bit 5 – „1” – voltage too low for measurement of freq.
Bit 4 – „1” – L3 phase voltage too low
Bit 3 – „1” – L2 phase voltage too low
Bit 2 – „1” – L1 phase voltage too low
Bit 1 – „1” – spent battery of RTC
Bit 0 – „1” – reactive 3-phase capacitive energy
63
Status Register 2 – alarms (address 4059, R):
Bity 15 ... 7 - reserved
Bit 6 – „1” – alarm 3 signalization
Bit 5 – „1” – alarm 2 signalization
Bit 4 – „1” – alarm 1 signalization
Bit 2 – „1” – alarm 3 activated
Bit 1 – „1” – alarm 2 activated
Bit 0 – „1” – alarm 1 activated
Register
address
Operations
Table 9
Range
4300
RW
0…61
Display panel illumination: 0 – off, 1-60
– illumination time in seconds from pressing the
button, 61 – always on
61
4301
RW
0 .. 60
Time of automatic switch
0...60s
0 – off
0
64
Description
Default
4302
RW
0...0x0FFF
Enabling page display
Bit0 – page 1, Bit1
– page 2, ...
0x0FFF
4303
RW
0, 01..09, 28..33,
35, 38
Page 1 display 1
01
4304
RW
0, 10..18, 28..33,
36, 38
Page 1 display 2
10
4305
RW
0,19..33, 37, 38
Page 1 display 3
19
4306
RW
0, 28..34, 38..41
Page 1 display 4
34
4307
RW
0, 42 .. 45
Page 1 display 5-6
0
4308
RW
0, 28, 30, 31, 38
Page 1 display 5
30
4309
RW
0, 29
Page 1 display 6
29
4310
RW
0, 01..09, 28..33,
35, 38
Page 2 display 1
35
4311
RW
0, 10..18, 28..33,
36, 38
Page 2 display 2
36
4312
RW
0,19..33, 37, 38
Page 2 display 3
37
4313
RW
0, 28..34, 38..41
4314
RW
0, 42 .. 45
4315
RW
0, 28, 30, 31, 38
Page 2 display 4
38
Page 2 display 5-6
0
Page 2 display 5
30
65
4316
RW
0, 29
Page 2 display 6
29
4317
RW
0, 01..09, 28..33,
35, 38
Page 3 display 1
02
4317
RW
0, 01..09, 28..33,
35, 38
Page 3 display 1
02
4318
RW
0, 10..18, 28..33,
36, 38
Page 3display 2
11
4319
RW
00,19..33, 37, 38
Page 3 display 3
20
4320
RW
00, 28..34, 38..41
Page 3 display 4
28
4321
RW
0, 42 .. 45
Page 3 display 5-6
0
4322
RW
00, 28, 30, 31, 38
Page 3 display 5
30
4323
RW
00, 29
Page 3 display 6
29
4324
RW
00, 01..09,
28..33, 35, 38
Page 4 display 1
03
4325
RW
00, 10..18,
28..33, 36, 38
Page 4 display 2
12
4326
RW
00,19..33, 37, 38
Page 4 display 3
21
4327
RW
00, 28..34, 38..41
4328
RW
0, 42 .. 45
4329
RW
00, 28, 30, 31, 38
66
Page 4 display 4
32
Page 4 display 5-6
0
Page 4 display 5
30
4330
RW
00, 29
Page 4 display 6
29
4331
RW
00, 01..09,
28..33, 35, 38
Page 5 display 1
04
4332
RW
00, 10..18,
28..33, 36, 38
Page 5 display 2
13
4333
RW
00,19..33, 37, 38
Page 5 display 3
22
4334
RW
00, 28..34, 38..41
Page 5 display 4
33
4335
RW
0, 42 .. 45
Page 5 display 5-6
0
4336
RW
00, 28, 30, 31, 38
Page 5 display 5
30
4337
RW
00, 29
Page 5 display 6
29
4338
RW
00, 01..09,
28..33, 35, 38
Page 6 display 1
05
4339
RW
00, 10..18,
28..33, 36, 38
Page 6 display 2
14
4340
RW
00,19..33, 37, 38
Page 6 display 3
23
4341
RW
00, 28..34, 38..41
Page 6 display 4
31
4342
RW
0, 42 .. 45
Page 6 display 5-6
46
4343
RW
00, 28, 30, 31, 38
Page 6 display 5
0
4344
RW
00, 29
Page 6 display 6
0
67
4345
RW
00, 01..09,
28..33, 35, 38
Page 7 display 1
06
4346
RW
00, 10..18,
28..33, 36, 38
Page 7 display 2
15
4347
RW
00,19..33, 37, 38
Page 7 display 3
24
4348
RW
00, 28..34, 38..41
4349
RW
0, 42 .. 45
Page 7 display 4
32
Page 7 display 5-6
42
4350
RW
00, 28, 30, 31, 38
Page 7 display 5
0
4351
4352
RW
00, 29
Page 7 display 6
0
RW
00, 01..09,
28..33, 35, 38
Page 8 display 1
07
4353
RW
00, 10..18,
28..33, 36, 38
Page 8 display 2
16
4354
RW
00,19..33, 37, 38
Page 8 display 3
25
4355
RW
00, 28..34, 38..41
4356
RW
0, 42 .. 45
4357
RW
4358
4359
68
Page 8 display 4
33
Page 8 display 5-6
43
00, 28, 30, 31, 38
Page 8 display 5
0
RW
00, 29
Page 8 display 6
0
RW
00, 01..09,
28..33, 35, 38
Page 9 display 1
08
4360
RW
00, 10..18,
28..33, 36, 38
Page 9 display 2
17
4361
RW
00,19..33, 37, 38
Page 9 display 3
26
4362
RW
00, 28..34, 38..41
4363
RW
0, 42 .. 45
Page 9 display 4
34
Page 9 display 5-6
44
4364
RW
4365
RW
00, 28, 30, 31, 38
Page 9 display 5
0
00, 29
Page 9 display 6
0
4366
RW
00, 01..09,
28..33, 35, 38
Page 10 display 1
09
4367
RW
00, 01..09,
28..33, 35, 38
Page 10 display 2
18
4368
RW
00,19..33, 37, 38
Page 10 display 3
27
4369
RW
00, 28..34, 38..41
Page 10 display 4
39
4370
RW
0, 42 .. 45
Page 10 display 5-6
45
4371
RW
00, 28, 30, 31, 38
Page 10 display 5
0
4372
RW
00, 29
Page 10 display 6
0
4373
RW
00, 01..09,
28..33, 35, 38
Page 11 display 1
29
4374
RW
00, 01..09,
28..33, 35, 38
Page 11 display 2
30
69
4375
RW
00,19..33, 37, 38
Page 11 display 3
31
4376
RW
00, 28..34, 38..41
Page 11 display 4
40
4377
RW
0, 42 .. 45
Page 11 display 5-6
42
4378
RW
00, 28, 30, 31, 38
Page 11 display 5
0
4379
RW
00, 29
Page 11 display 6
0
4380
RW
00, 01..09,
28..33, 35, 38
Page 12 display 1
29
4381
RW
00, 01..09,
28..33, 35, 38
Page 12 display 2
30
4382
RW
00,19..33, 37, 38
Page 12 display 3
31
4383
RW
00, 28..34, 38..41
Page 12 display 4
41
4384
RW
0, 42 .. 45
Page 12 display 5-6
47
4385
RW
00, 28, 30, 31, 38
Page 12 display 5
0
4386
RW
00, 29
Page 12 display 6
0
70
32-bit register
address
Operations
6000/7000
7500
R
L1 phase voltage
V
6002/7002
7501
R
L1 phase current
6004/7004
7502
R
L1 phase active power
3Ph/3W

x
A


W

x
Unit
3Ph/4W
Description
16-bit register
address
Table 10
6006/7006
7503
R
L1 phase reactive power
VAr

x
6008/7008
7504
R
L1 phase apparent power
VA

x
6010/7010
7505
R
L1 phase active power factor
(PF1=P1/S1)
-

x
6012/7012
7506
R
tgϕ factor of L1 phase
(tg1 =Q1/P1)
-

x
6014/7014
7507
R
THD U1
V/%

x
6016/7016
7508
R
THD I1
A/%

x
6018/7018
7509
R
L2 phase voltage
V

x
6020/7020
7510
R
L2 phase current
A


71
6022/7022
7511
R
L2 phase active power
W

x
6024/7024
7512
R
L2 phase reactive power
VAr

x
6026/7026
7513
R
L2 phase apparent power
VA

x
6028/7028
7514
R
L2 phase active power factor
(PF2=P2/S2)
-

x
6030/7030
7515
R
tgϕ factor of L2 phase
(tg2 =Q2/P2)
-

x
6032/7032
7516
R
THD U2
V/%

x
6034/7034
7517
R
THD I2
A/%

x
6036/7036
7518
R
L3 phase voltage
V

x
6038/7038
7519
R
L3 phase current
A


6040/7040
7520
R
L3 phase active power
W

x
6042/7042
7521
R
L3 phase reactive power
VAr

x
6044/7044
7522
R
L3 phase apparent power
VA

x
6046/7046
7523
R
L3 phase active power factor
(PF3=P3/S3)
-

x
6048/7048
7524
R
tgϕ factor of L3 phase
(tg3 =Q3/P3)
-

x
6050/7050
7525
R
THD U3
V/%

x
72
6052/7052
7526
R
THD I3
A/%

x
6054/7054
7527
R
Mean 3-phase voltage
V

x
6056/7056
7528
R
Mean 3-phase current
A


6058/7058
7529
R
3-phase active power
(P1+P2+P3)
W


6060/7060
7530
R
3-phase reactive power
(Q1+Q2+Q3)
VAr


6062/7062
7531
R
3-phase apparent power
(S1+S2+S3)
VA


6064/7064
7532
R
3-phase active power factor
(PF=P/S)
-


6066/7066
7533
R
mean tgϕ factor for 3 phases
(tg=Q/P)
-


6068/7068
7534
R
Frequency
F


6070/7070
7535
R
Phase-to-phase voltage L1-2
V


6072/7072
7536
R
Phase-to-phase voltage L2-3
V


6074/7074
7537
R
Phase-to-phase voltage L3-1
V


6076/7076
7538
R
Mean phase-to-phase voltage
V


73
6078/7078
7539
R
active power averaged
(P Demand)
W


6080/7080
7540
R
apparent power averaged
(S Demand )
VA


6082/7082
7541
R
current averaged (I Demand)
A


6084/7084
7542
R
THD U mean 3-phase
V/%

x
6086/7086
7543
R
THD I mean 3-phase
A/%

x
6088/7088
7544
R
Neutral wire current (calculated
from vectors)
A

x
6090/7090
7545
R
Active 3-phase input energy (no. of
register 7546 overﬂows, resets to 0
after reaching 99999.9 MWh)
100
MWh


6092/7092
7546
R
Active 3-phase input energy (counter
counting up to 99999.9 kWh)
kWh


6094/7094
7547
R
Active 3-phase output energy (no. of
register 7548 overﬂows, resets to 0
after reaching 99999.9 MWh)
100
MWh


6096/7096
7548
R
Active 3-phase output energy (counter
counting up to 99999.9 kWh)
kWh


6098/7098
7549
R
Reactive 3-phase inductive energy
(no. of register 7550 overﬂows, resets
to 0 after reaching 99999.9 MVArh).
100
MVArh


6100/7100
7550
R
Reactive 3-phase inductive energy
(counter counting up to 99999.9
kVArh)
kVArh


74
6102/7102
7551
R
Reactive 3-phase capacity energy
(no. of register 7552 overﬂows, resets
to 0 after reaching 99999.9 MVArh)
100
MVArh


6104/7104
7552
R
Reactive 3-phase capacity energy
(counter counting up to 99999.9 kVArh)
kVArh


6106/7106
7553
R
Apparent energy (no. of register
7554 overﬂows, resets to 0 after
reaching 99999.9 MVAh)
100
MVAh


6108/7108
7554
R
Apparent energy (counter counting
up to 99999.9 kVAh)
kVAh


6110/7110
7555
R
Time – seconds
-


6112/7112
7556
R
Time – hours, minutes
-


6114/7114
7557
R
Reserved
-


6116/7116
7558
R
Reserved
-


6120/7118
7559
R
Mean 3-phase current (max)
A


6120/7120
7560
R
Max 3-phase voltage phase / phase-to-phase for 3PH-4 – 3-phase,
4-wire - max phase for 3PH-3 –
3-phase, 3-wire - max phase-to-phase
V


6122/7122
7561
R
Active power averaged (P Demand) min
W


6124/7124
7562
R
Active power averaged (P Demand) max
W


6126/7126
7563
R
Apparent power averaged (S Demand) max
VA


6128/7128
7564
R
Current averaged (I Demand) max
A


In case of exceeding (measuring value is out of the measuring range)
the value 1e20 is set.
75
9. ERROR CODES
During the meter operation the error messages may be displayed. Following list shows reasons of errors.
- Er1 – if too low voltage or current during measurement:
less than 10% Un,
- PFi, tgϕi,THDUi,
less than 0,2% In,
- PFi, tgϕi,
less than 10% In,
- THDIi,
76
- Er2 – during THD measurement, when frequency
value is outside 48 – 52 Hz range for 50 Hz
and 58 – 62 for 60 Hz;
- Err bat – displayed when the battery of the internal
RTC clock is used up. The measurement is carried out after switching
the
supply
on
and
every
day
at midnight. You can disable the message
by the push-button
. The disabled message
remains inactive till the renewed switching of
the meter on.
- Err CAL, Err EE – displayed when the meter memory
is damaged. A meter should be sent back to
the manufacturer.
- Err PAr – incorrect operational parameters of the
meter. In such case a meter should be set
to manufacturer settings (from menu or via
RS-485 interface). Message can be disabled
by pressing
.
-
---
– exceedance. Measuring value is out of the
measuring range.
10. ACCESSORIES
For the N43 meters you can order:
USB CABLE A/miniUSB - 1m BLACK;
Order code 1126-271-028.
77
11. TECHNICAL DATA
Measuring ranges and permissible basic errors
Table 11
Measured value
Current In
1 A~
5 A~
63 A~
Measuring range
L1
L2
0.002 ...1.20 A or kA *
0.010 ... 6.00 A or kA *
0.10 ... 76.0A~


L3
∑

Basic
error**
0.5 %
Voltage L-N
57,7 V~
230 V~
290 V~
2.80 ..70.0 V or kV*
10.0 .. 276 V~
14.0 .. 348 V~



0.5 %
Voltage L-L
100 V~
400 V~
500 V~
5.00 .. 120 V or kV*
20.0 .. 480 V~
25.0 .. 600 V~



1 %
Frequency
47.0 .. 63.0 Hz

0.5 %
Active power
/consumed or exported/
0.00 .. 999
W, kW or MW




1 %
0.00 .. 999
VAr, kVAr lub MVAr




1 %
0.00 .. 999
VA, kVA or MVA




1 %
Reactive power
/capacity or inductive/
Apparent power
78
Active energy
/consumed or
exported/
0.0 .. 99999.9
kWh or MWh
Reactive energy
/capacity or inductive/
0.0 .. 999999.9
kVArh or MVArh
Apparent energy
0.0 .. 999999.9
kVAh or MVAh
Active power factor PF
Tangent 




1 %

1 %

1 %
-1 ... 0 ... 1




1 %
-1.2 ... 0 ...1.2




1 %
* Depending on the setting of trU (voltage transformer ratio:
0.1 ... 4000.0) and trI (current transformer ratio: 1 ... 10000)
** Calculated for the nominal range In, Un
Power consumption:
- in current circuit
- in voltage circuit
- in current circuit
Readout ﬁeld
≤ 4 VA
≤ 0.05 VA
≤ 2.00 VA
dedicated 3.5” LCD display,
79
Relay outputs
3 x relays,
volt-free NO contacts
load capacity 0,5 A 250 V AC;
1 A 30 V DC;
Serial interface
RS485: address 1..247
mode: 8N2, 8E1, 8O1,8N1
baud rate: 4.8, 9.6, 19.2, 38.4 kbit/s
transmission protocol: Modbus RTU
maximum time to start the response:
600 ms
USB: 1.1/2.0, address 1, mode 8N2;
baud rate 9.6 kbit/s,
transmission protocol: Modbus RTU
maximum time to start the response:
800 ms,
USB wire length ≤ 3 m
Energy pulse output
OC (NPN) output, class A passive,
compliant with EN 62053-31;
supply voltage 18...27 V,
current 10...27 mA
80
Pulsing constant
of OC output
Terminals
5000 - 20000 pulses/kWh for
In=1A/5 A independently of set tr_U, tr_I;
100 – 1000 pulses/kWh for In=63 A
direct
connection (63 A)
Diameter
solid-core wire 2.5 ... 16 mm&sup2;
stranded wire 4 ... 16 mm&sup2;
Clamping
screws M5
Tightening
torque 1.2 ... 2.0 Nm
indirect
connection (1/5 A)
0.2 ... 5.3 mm2
0.2 ... 5.3 mm2
M3.5
1.0 Nm
Protection grade of the housing
from the front
IP 50
from terminals side
IP 00
81
Weight
0.3 kg
Dimensions
105 x 110 x 60 mm
Reference and rated operating conditions:
- supply voltage
85..253 V a.c. (40...400) Hz
or 90..300 V d.c.
20..40 V a.c. (40...400) Hz
lub 20..60 V d.c.
- input signal:
0 ... 0.002..1.2In; 0.05...1.2Un
for current, voltage
0...0.002...1.2In; 0...0.1...1.2Un;
for factors PFi ,tϕi
frequency 47...63 Hz;
sinusoidal ( THD ≤ 8% )
- power factor
-1...0...1
- ambient temperature
-10..23..+55oC
- storage temperature
-20...+70oC
- humidity
0...95 % (inadmissible condensation)
- max peak factor:
- current
2
- voltage
2
82
- external magnetic ﬁeld 0...40...400 A/m
- short-term overload
voltage inputs
5 sec. 2 Un
voltage inputs
1 sec. 50 A
/version
In 1A/5 A /
1 sec. 630 A
/version
In 63 A /
- working position
any
- warm-up time
5 min.
Real time clock battery:
CR2032
Additional errors:
in % of the basic error
- from ambient temperature changes
- for THD &gt; 8%
&lt; 50 % / 10oC
&lt; 100 %
Test voltages:
- supply and alarm outputs
2.1 kV d.c.
83
- voltage and current inputs
- USB, RS-485 and OC outputs
3.2 kV d.c.
0.7 kV d.c.
Standards fulﬁlled by the meter:
Electromagnetic compatibility:
- noise immunity acc. to EN 61000-6-2
- noise emission acc. to EN 61000-6-4
Safety requirements:
acc. to EN 61010-1 standard
•
isolation between circuits: basic,
•
installation category III (for voltages above 300 V – category II)
•
pollution grade 2,
•
maximum phase-to-earth operating voltage:
- for supply circuits and relay outputs 300 V
- for measuring input 300 V – cat III (600 V – cat II)
- for circuits RS-485, USB, pulse output: 50 V
•
altitude a.s.l. &lt; 2000m.
84
12. ORDERING CODE
N43 network parameters meter ordering code.
N43 - X
Current input In:
1 A/5 A (X/1; X/5)
63 A
Voltage input (phase/ phase-to-phase) Un:
3 x 57.7/100 V
3 x 230/400 V
3 x 290/500 V
Auxiliary supply:
85...253 V a.c., 90...300 V d.c.
20...40 V a.c., 20...60 V d.c.
Version:
standard
custom-made*
Language:
Polish
English
other*
Acceptance tests:
without extra quality requirements
with an extra quality inspection certiﬁcate
acc. to customer’s request*
* -after agreeing with the manufacturer
X
X
Table 12
XX X X
1
2
1
2
3
1
2
00
XX
P
E
X
0
1
X
85
EXAMPLE OF ORDER:
The code N43 - 2 2 1 00 E 0 means:
N43 - meter of network parameters of N43 type
2 - current input: 63 A
2 - input voltage (phase/phase-to-phase)
Un = 3 x 230 V/ 400 V
1 - auxiliary supply: 85...253 V a.c., 90...300 V d.c.
00 - standard version
E - all descriptions and user’s manual in English
0 - without extra quality requirements.
86
87
Export department:
tel.: (+48 68) 45 75 139, 45 75 233, 45 75 321, 45 75 386
fax.: (+48 68) 32 54 091
e-mail: [email protected]
88
N43-09A
LUMEL S.A.
ul. Słubicka 1, 65-127 Zielona G&oacute;ra, POLAND
tel.: +48 68 45 75 100, fax +48 68 45 75 508
www.lumel.com.pl
">
Hello! I am an AI chatbot specifically trained to assist you with the Lumel N43 User manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!