CLD54D / DNL54D User Manual CLD54D / DNL54D User Manual

CLD54D / DNL54D User Manual CLD54D / DNL54D User Manual
CLD54D / DNL54D
User Manual
www.rainbowcctv.com
v1.0
① Video output connector (BNC)
1Vp-p/75Ω composite video signal output connector.
② OSD Control
Controls for OSD - On Screen Display
③ Power LED
This LED turns ON only when the power is supplied properly and the
converter (or the regulator) inside the camera works sell.
④ Backfocus Mode Button
Eliminate the hassle of backfocusing. No more filters or numerous
adjustments.
Procedure:
1. Push and hold the BACKFOCUS MODE button. The lens iris will
open automatically and the Electronic lris will turn on to prevent
a washed out picture.
2. Adjust the lens for proper focus. If the lens focus range is not
sufficient, adjust the focus screw on the side of the camera.
3. Release the BACKFOCUS MODE button, The lens iris will return
to normal and the Electronic lris will turn off. You're finished!
The camera and lens are now backfocused for proper day and
night operation.
⑤ RS-485 Connector
Thi
This connector
t allows
ll
ffor external
t
l control
t l off the
th camera (Pelco
(P l D).
D)
⑥ Power input connector (push terminal connector)
Recommended Power Supply (12V DC)
Consumption 180 ~ 220mA DC
Use only regulated power supply.
Recommended Power Supply (24V AC)
Consumption 100 ~ 150mA AC.
CAUTIONS
1. Connecto to a Class 2 Power Supply only for both of DC 12V
AC 24V.
2. To prevent fire or shock hazard, the UL listed wire VW_I,
style 1007 should be used for the cable for DC 12V or
⑦ Camera Mount
For mounting the camera to standard 1/4-20 mounts
This mount can be mounted on the top or bottom of the camera.
To install this on the top of the camera, remove the "PASSED" label
first and move the mount from the bottom of the camera.
⑧ Backfocus Adjustment Screw
This screw is for performing backfocus of the lens and camera.
Adjust if the lens focus is not providing a clear picture.
⑨ C-MOUNT ADAPTER RING
When using CS-mount lens (Flange back = 12.5mm), remove
this C-mount adapter ring.
This adapter ring must be in place when using C-mount lenses.
⑩ Dust Camp
Remove this cap just before installing the lens.
Do not handle or leave the camera with this cap removed.
⑪ Auto
A
iiris
i llens selection
l i
switch.
i h
DC for lenses without internal amp. Camera will control the iris.
VIDEO for lenses with internal amp. Lens will control its own iris.
⑫ Auto Iris Lens Connector
This connector is for DC drive or Video drive lens.
It supplies the control signals to auto iris lens.
⑬ Backfocus Lock Screw
The position of the CCD can be locked into place after final
adjustment. Please reference the instructions below.
1. Adjust the backfocus of the camera
after installing the lens if you find the
lens focus does not provide enough
range.
2. Tighten the lock screw on the camera
to keep the mechanism from moving
due to vibration or movement of the
camera.
OSD adjustment
OSD Direction & Enter button in rear plate
* To access OSD menu, push the SET UP button.
OSD menu description
Main menu
EXPOSURE
IMAGE
FUNCTION
EFFECT
PRIVACY
SYSTEM
OPTION
EXIT
Sub menu
OSD adjustment
LENS
MANUAL/DC selectable
AGC
0/18/24/33 selectable
AWB MODE
AWC/ATW/MANUAL/PUSH selectable
R-Y GAIN
0 ~ 255 selectable
B-Y GAIN
0 ~ 255 selectable
SHARPNESS
0 ~ 49 selectable
GAMMA SET
0.3, 0.35, 0.4, 0.45, 0.5, 0.55, 0.6, 1 selectable
D&N MODE
AUTO/COLOR/B&W/EX-CONT selectable
BURST
ON/OFF selectable
COLOR → BW
0 ~ 255 selectable
BW → COLOR
0 ~ 213 selectable
DLY(delay) TIME
3~12 selectable
MIRROR
ON/OFF selectable
LSC
ON/OFF selectable
HLM
ON/OFF selectable
BLC
ON/OFF selectable
WIDE BLC
ON/OFF selectable
MASK 1
ON/OFF selectable
MASK 2
ON/OFF selectable
MASK 3
ON/OFF selectable
MASK 4
ON/OFF selectable
COLOR SET
Mask color can be shown with 3 color (Red, Blue,Black)
TITLE
ON/OFF selectable
FACTORY SET
Load factory defaults
BLACK BOARD
ON/OFF selectable
SPLIT
ON/OFF selectable
DPC SET
ON/OFF selectable
SYNC MODE
INTERNERAL/AUTO selectable
ID
0 ~ 254 selectable
BAUDRATE
2400/4800/9600/14400/19200/38400 selectable
PROTOCOL
PELCO D
SAVE/EXIT
Save settings and exit
RELOAD & EXIT
Reload previous settings
EXIT
Exit the OSD menu
OSD Menus
Use the OSD adjustment to navigate the menus, press the button for "Enter"
SETUP menu
Description
EXPOSURE
LENS SEL.
BRIGHT
DC LV.
SHUTTER
AGC
DC
35
35
1/60
24 DB
1. LENS SEL : This menu is for lens application.
Lens Type Lens Sel.
Shutter
Switch on side of camera setting
DC
DC
1/60 (1/50 PAL)
DC
Video
DC
1/60 (1/50 PAL)
Video
Manual
MANUAL
AUTO
N/A
EXPOSURE
Shutter speed can also be set manually
* NTSC : AUTO(1/60-1/100,000), 1/60, 1/100FLC, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000, 1/100000
* PAL : AUTO(1/50-1/100,000), 1/50, 1/100, 1/120FLC, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000, 1/100000
2. BRIGHT : Brightness is adjustable from 0~100.
3. DC LV : DC drive lens level is adjustable from 0 to 100
4. AGC : AGC gain adjustable as a step (0.18,24,33). Higher values will increase sensitivity.
* Note : Higher AGC levels will increase the amount of "noise" in the picture.
IMAGE
AWB MODE
R GAIN
B GAIN
R_Y GAIN
B_Y GAIN
SHARPNESS
GAMMA SET
ATW
100
100
128
128
20
0.45
1. AWB MODE : AWC, ATW, Manual and Push are selectable.
IMAGE
* AWC : Auto white balance works infinitely
Note : when monitoring a single color the camera will attempt to adjust until the picture is white
* ATW : Fixing Auto white balance from 2500k~ 8500k° approximately.
* MANUAL : The range of White balance is adjustable with R GAIN and B GAIN (fixed white balance)
Note : R GAIN & B GAIN is available in Manual mode ( each is adjustable from 0 to 255,)
* PUSH: White balance is fixed to the current color temperature.
Note : if this mode is selected, Auto white balance does not work.
2. R-Y GAIN : Red gain adjustable from 0 to 255.
3. B-Y GAIN : Blue gain adjustable from 0 to 255.
4. SHARPNESS : sharpness is adjustable from 0 to 49
5. GAMMA SET : Gamma characteristic is adjustable with 0.3, 0.35, 0.4, 0.45, 0.5, 0.55, 0.6, 1 .
FUNCTION
DN MODE
BURST
COLOR▶BW
BW▶COLOR
DLY TIME
COLOR
OFF
120
80
3
1. DN MODE : Day & Night function is selectable as below.
FUNCTION
* AUTO : camera will be color during the day and B&W at night
* COLOR : camera will remain in color at all times
* BW : camera will remain in B&W at all times
2. BURST : Burst ON/ OFF is adjustable (only available in AUTO and EX-CONT mode)
3. COLOR ▶ BW : controls the switching point from Color to B&W for day/night mode
--> Higher numbers will cause the camera to switch to B&W in darker scenes
4. BW ▶ Color : controls the switching point from B&W to Color to for day/night mode
--> Higher numbers will cause the camera to switch to Color in darker scenes
5. DLY TIME : Adjusts the delay time when switching day/night modes
--> Higher numbers will increase the delay
EFFECT
MIRROR
OFF
LSC
OFF
LSC GAIN
HLI
OFF
HLI THR
BLC
8
10
1. MIRROR : Mirror function on/off is selectable.
2. LSC (lens shading compensation) : this function helps prevent darker edges (shading) that can occur with some lenses.
--> Higher values will increase the compensation
3. HLI (High Light Inversion) :
Helps "mask" bright areas of the scene (like car headlights or bright street lights)
EFFECT
HLI OFF mode
HLI ON mode
4. BLC : adjusts the sensitivity of BLC (Backlight Compensation).
WEIGHT allows access to the 5 BLC zones.
Each BLC zone has number showing BLC sensitivity adustable from 0 to 255.
0
0
255
A higher number increases the BLC sensitivity.
0
* Note : only the center zone is set to 255 by default
0
5. WIDE BLC : Digitial WDR (Wide Dynamice Range) to help balance out high contrast scenes and prevent washout..
PRIVACY
PRIVACY
MASK1
OFF
SET AREA↓
MASK2
OFF
SET AREA↓
MASK3
OFF
SET AREA↓
MASK4
OFF
SET AREA↓
COLOR
BLACK
This mode allows for up for Privacy Zones (masks) to cover areas that are not be viewed or recorded
Up to for zones can be selected (Mask 1, 2, 3, 4)
After turning the mask on, select SET AREA to create the mask
To create a mask area (press Enter to switch between the colors below):
* When the mask is Red it can be adjusted in size Up and Left
* When the mask is Blue it can be adjusted in size Down and Right
* When the mask is Black you can return to the menu by moving in any direction
You can select the COLOR of the masks at the bottom of the menu
SYSTEM
TITLE
ON
EDIT↓
POSITION
TOP_L
FACTORY SET↓
BACKBOARD ON
SPLIT
OFF
1. TITLE : Turning this mode ON will allow the camera to display and ID number or title
- EDIT : after pushing the SET UP button, each character appears with the vertical order as shown below.
* To erase a character, choose the empty mark among the characters
SYSTEM
SYSTEM
SYSTEM
O
P
Q
R
[C A M S
T
U
]
[C A M
]
▲
↓
This is delete (empty )mark
for erasing a wrong entry
]
■
<TITLE wording>
<Erasing word>
* Note : move the cursor all the way right after finishing before hitting enter (SET UP button).
- POSITION : the location of the title can be adjusted here
2. FACTORY SET : If push SET, all camera values retun to the factory default values.
3. BACKBOARD : OSD backboard (background) can be turned ON or OFF.
4. SPLIT : it splits the monitoring picture into two pictures.
SPECIAL
DPC SET
WHITE TH
BLACK TH
LUM TH
SYNC MODE
V_PHASE
ID
BAUDRATE
PROTOCOL
OPTION
OFF
30
50
150
INTER
0
1
2400
PELCO_D
1. DPC (Defective Pixel Cancelling) SET : compensates for white and black defects on the CCD
- WHITE TH : a white defect is compensated with an adjustment value from 0 To 255
- BLACK TH : a black defect is compensated with an adjustment value from 0 to 255
- LUM TH : a luminance is compensated with an adjustment value from 0 To 255
2. SYNC MODE : camera sync. is selectable.
INTER : for Internal sync. AUTO : for Line-lock
* V-PHASE is available only in AUTO mode (from 0 to 199)
3. ID : selects the camera ID for RS485 communication with external devices.
ID number can be set from 0 to 254
4. BAUDRATE : adjust the baud rate to match the RS485 communcation speed of the external device
6. PROTOCOL : PELCO-D
EXIT
SAVE/EXIT↓
RELOAD/EXIT↓
EXIT↓
EXIT
1. SAVE / EXIT
:
Select to SAVE all changes made
2. RELOAD/EXIT
Select to RELOAD the previous settings saved before entering the menus
Note : this is not recover the factory default values.
3. EXIT :
If user do not want to save the new adjusted values, select this item
SPECIFICATIONS FOR CLD54D
NTSC (CLD54D) / PAL (CLD54DX)
Video Signal System
Image Sensor
Interline 1/3" Sony Super HAD-Ⅱ CCD
Image Output
VBS compoite 1.0Vp-p/75 ohms
Scanning System
2:1 Interlace
Resolution (horizontal)
540 TV lines or more at center
Sensitivity (F1.2)
0.1 Lux
S/N Ratio
48dB or more (AGC-OFF)
Gamma Characteristics
0.45
Effective Picture Elements
768(H) x 494(V) (NTSC), 752(H) x 582(V) (PAL)
Synchronization System
Internal / Linelock (OSD)
Auto lris Control
Video iris / DC iris (Switchable)
Auto Electronic Shutter (AES)
1/60 ~ 1/100,000 linear (NTSC), 1/50 ~ 1/100,000 (PAL)
Automatic Gain Control (AGC)
On / Off Selectable (Adjustable levels of 0, 18, 24, 32dB)
Back Light Compensation (BLC) On / Off Selectable (5 Area Masking)
AWC / ATW / Manual
White Balance
Digital WDR
Off / WDR / BLC Selectable
High Light Inversion
On / Off Selectable
Privacy Masking
On / Off (4 Programmable Zone)
Video Control
Reverse, Posi / Nega, Sharpness
Day & Night Function
Color / BW / Auto (camera is not IR sensitive)
OSD
Camera ID & Functions Selectable
Lens Mount
CS-mount (C-mount adapter included)
Power Supply (dual power)
12VDC/24VAC ±10% (Isolated Power Supply Built Into Camera)
Power Consumption
5W or less
Ambient temp.(operation)
+14 ~ 122°F (-10°C ~ +50°C) Within 85% RH
Ambient Humid.(operation)
85%RH or less
External Dimensions
1.9 × 1.9 × 3.3 inches (47 × 47 × 83mm)
Weight
Terminal (Rear side)
7.1 oz. (200g)
Video Output : BNC
Power Input : 2-Pin Push Terminal
DC/VIDEO Auto Iris Lens Select Switch
A.I Lens, DC Drive Lens : 4-Pin Square DIN (Switch)
Back Focus Adjustment
DIMENSIONS
One Touch Screw Driving System
SPECIFICATIONS FOR DNL54D
Video Signal System
Image Sensor
NTSC (DNL54D) / PAL (DNL54DX)
Image Output
VBS compoite 1.0Vp-p/75 ohms
Scanning System
2:1 Interlace
Resolution (horizontal)
540 TV lines or more at center
Sensitivity (F1.2)
0.03 Lux
S/N Ratio
48dB or more (AGC-OFF)
Gamma Characteristics
0.45
Effective Picture Elements
768(H) x 494(V) (NTSC), 752(H) x 582(V) (PAL)
Synchronization System
Internal / Linelock (OSD)
Auto lris Control
Video iris / DC iris (Switchable)
Auto Electronic Shutter (AES)
1/60 ~ 1/100,000 linear (NTSC), 1/50 ~ 1/100,000 (PAL)
Automatic Gain Control (AGC)
On / Off Selectable (Adjustable levels of 0, 18, 24, 32dB)
Interline 1/3" Sony Super HAD-Ⅱ CCD
Back Light Compensation (BLC) On / Off Selectable (5 Area Masking)
AWC / ATW / Manual
White Balance
Digital WDR
Off / WDR / BLC Selectable
High Light Inversion
On / Off Selectable
Privacy Masking
On / Off (4 Programmable Zone)
Video Control
Reverse, Posi / Nega, Sharpness
Day & Night Function
Color / BW / Auto
OSD
Camera ID & Functions Selectable
Lens Mount
CS-mount (C-mount adapter included)
Power Supply (dual power)
12VDC/24VAC ±10% (Isolated Power Supply Built Into Camera)
Power Consumption
5W or less
Ambient temp.(operation)
+14 ~ 122°F (-10°C ~ +50°C) Within 85% RH
Ambient Humid.(operation)
85%RH or less
External Dimensions
1.9 × 1.9 × 3.3 inches (47 × 47 × 83mm)
Weight
Terminal (Rear side)
7.1 oz. (200g)
Video Output : BNC
Power Input : 2-Pin Push Terminal
DC/VIDEO Auto Iris Lens Select Switch
A.I Lens, DC Drive Lens : 4-Pin Square DIN (Switch)
Back Focus Adjustment
DIMENSIONS
One Touch Screw Driving System
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement