L16RE-2V data shEEt
L16RE-2V data sheet for Renewable Energy and Backup Power Applications PREMIUM LINE Model: L16RE-2V with Bayonet Cap Dimensions: inches (mm) Battery: Flooded/wet lead-acid battery Color: Maroon (case/cover) Material:Polypropylene Product Specification ENERGY (kWh) CAPACITY A Amp-Hours (AH) BCI GROUP SIZE TYPE 903 L16RE-2V* 2-Hr Rate 5-Hr Rate 10-Hr Rate 20-Hr Rate 722 909 1021 1110 48-Hr Rate 72-Hr Rate 100-Hr Rate 100-Hr Rate VOLTAGE TERMINAL Type DIMENSIONS B Inches (mm) Length Width Height C 11-5/8 (295) 7 (178) 17-11/16 (450) WEIGHT lbs. (kg) Premium Line - DEEP-CYCLE FLOODED BATTERIES 1182 1210 1235 2.47 2 VOLT Charging Instructions 5 119 (54) TERMINAL CONFIGURATIONS Charger Voltage Settings (at 77°F/25°C) 5 LT Voltage per cell Absorption charge 2.35-2.45 Float charge 2.20 Equalize charge 2.58 Do not install or charge batteries in a sealed or non-ventilated compartment. Constant under or overcharging will damage the battery and shorten its life as with any battery. L-Terminal Terminal Height Inches (mm) 1-3/4 (43) Torque Values LB-IN (Nm) 100 – 120 (11 – 14) Through-hole Diameter (mm) 3/8 (10) * Polyon™ Case operational data Operating Temperature Self Discharge Specific Gravity -4°F to 113°F (-20°C to +45°C). At temperatures below 32°F (0°C) maintain a state of charge greater than 60%. Up to 4% per week The specific gravity at 100% state-ofcharge is 1.280 Premium Line batteries manufactured prior to March 2012 have 1.260 SG value. Charging temperature compensation To the Voltage Reading -- Subtract 0.005 volt per cell (VPC) for every 1°C above 25°C or add 0.005 volt per cell for every 1°C below 25°C. Expected life vS. Temperature Chemical reactions internal to the battery are driven by voltage and temperature. The higher the battery temperature, the faster chemical reactions will occur. While higher temperatures can provide improved discharge performance the increased rate of chemical reactions will result in a corresponding loss of battery life. As a rule of thumb, for every 10°C increase in temperature the reaction rate doubles. Thus, a month of operation at 35°C is equivalent in battery life to two months at 25°C. Heat is an enemy of all lead acid batteries, FLA, AGM and gel alike and even small increases in temperature will have a major influence on battery life. The amount of amp-hours (AH) a battery can deliver when discharged at a constant rate at 80°F (27°C) for Premium Line and maintain a voltage above 1.75 V/cell. Capacities are based on peak performance. Dimensions are based on nominal size. Dimensions may vary depending on type of handle or terminal. Batteries to be mounted with .5 inches (12.7 mm) spacing minimum. Dimensions taken from bottom of the battery to the highest point on the battery. Heights may vary depending on type of terminal. Trojan’s battery testing procedures adhere to both BCI and IEC test standards. Made in the USA Page 1 of 2 L16RE-2V_TRJNRE_ DS_1012 A. B. C. L16RE-2V data sheet for Renewable Energy and Backup Power Applications PREMIUM LINE Battery dimensions (shown with LT) 16-11/16 (424) 17-11/16 (450) Height 15-7/8 (402) 11-5/8 (295) 7 (178) Width Length Typical cycle life in a stationary application 140 60 4000 120 50 3500 100 3000 80 2500 60 2000 40 4500 Number of Cycles Percent capacity vs. temperature 40 30 20 10 1500 0 20 1000 -10 0 500 -20 -20 0 20% 30% 40% 50% 60% 70% Depth-of-Discharge 80% 90% 100% -30 -40 0% 20% 40% 60% 80% 100% -40 120% call 800.423.6569 or + 1.562.236.3000 or visit www.trojanbatteryRE.com 12380 Clark Street, Santa Fe Springs, CA 90670 • USA or email [email protected] © 2012 Trojan Battery Company. All rights reserved. Trojan Battery Company is not liable for damages that may result from any information provided in or omitted from this publication, under any circumstances. Trojan Battery Company reserves the right to make adjustments to this publication at any time, without notices or obligation. Page 2 of 2 L16RE-2V_TRJNRE_ DS_1012 Trojan batteries are available worldwide. We offer outstanding technical support, provided by full-time application engineers.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project