Operating Instructions Blu-ray Disc Player

Add to my manuals
33 Pages

advertisement

Operating Instructions Blu-ray Disc Player | Manualzz
DMP_BD30_Cover.fm 1 ページ
2008年3月5日 水曜日 午後3時57分
Operating Instructions
Blu-ray Disc Player
Model No. DMP-BD30
Dear customer
Thank you for purchasing this product.
For optimum performance and safety, please read these instructions carefully.
Before connecting, operating or adjusting this product, please read the instructions completely. Please keep this manual for future reference.
Region management information
BD-Video
This unit plays BD-Video marked with labels containing the region code A.
Example:
DVD-Video
This unit plays DVD-Video marked with labels containing the region number “1” or “ALL”.
Example:
1
ALL
1
2
4
If you have any questions contact
[[U.S.A.]:1-800-211-PANA(7262)
[Canada]:1-800-561-5505
[[U.S.A.]:The warranty can be found on page 30.
[Canada]:The warranty can be found on page 31.
La referencia rápida en español se puede encontrar en la página 32.
PP
RQT9139-1Y
DMP-BD30PP_Book1.book
2 ページ
2008年1月29日 火曜日 午後1時46分
Getting started 11 IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the applicable safety instructions
listed below. Keep these operating instructions handy for future reference.
1) Read these instructions.
10)Protect the power cord from being walked on or pinched
2) Keep these instructions.
particularly at plugs, convenience receptacles, and the point
3) Heed all warnings.
where they exit from the apparatus.
4) Follow all instructions.
11)Only use attachments/accessories specified by the
5) Do not use this apparatus near water.
manufacturer.
6) Clean only with dry cloth.
12)Use only with the cart, stand, tripod, bracket, or
7) Do not block any ventilation openings. Install in accordance with
table specified by the manufacturer, or sold with
the manufacturer’s instructions.
the apparatus. When a cart is used, use caution
8) Do not install near any heat sources such as radiators, heat
when moving the cart/apparatus combination to
registers, stoves, or other apparatus (including amplifiers) that
avoid injury from tip-over.
produce heat.
13)Unplug this apparatus during lightning storms or
9) Do not defeat the safety purpose of the polarized or
when unused for long periods of time.
grounding-type plug. A polarized plug has two blades with one
14)Refer all servicing to qualified service personnel. Servicing is
wider than the other. A grounding-type plug has two blades and
required when the apparatus has been damaged in any way,
a third grounding prong. The wide blade or the third prong are
such as power-supply cord or plug is damaged, liquid has been
provided for your safety. If the provided plug does not fit into your
spilled or objects have fallen into the apparatus, the apparatus
outlet, consult an electrician for replacement of the obsolete
has been exposed to rain or moisture, does not operate
outlet.
normally, or has been dropped.
WARNING:
THE FOLLOWING APPLIES ONLY IN THE U.S.A.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR
PRODUCT DAMAGE,
≥DO NOT EXPOSE THIS APPARATUS TO RAIN, MOISTURE,
DRIPPING OR SPLASHING AND THAT NO OBJECTS FILLED
WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON
THE APPARATUS.
≥USE ONLY THE RECOMMENDED ACCESSORIES.
≥DO NOT REMOVE THE COVER (OR BACK); THERE ARE NO
USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
CAUTION!
DO NOT INSTALL OR PLACE THIS UNIT IN A BOOKCASE,
BUILT-IN CABINET OR IN ANOTHER CONFINED SPACE.
ENSURE THE UNIT IS WELL VENTILATED. TO PREVENT RISK
OF ELECTRIC SHOCK OR FIRE HAZARD DUE TO
OVERHEATING, ENSURE THAT CURTAINS AND ANY OTHER
MATERIALS DO NOT OBSTRUCT THE VENTILATION VENTS.
CAUTION!
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE
OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF.
REFER SERVICING TO QUALIFIED PERSONNEL.
CAUTION
Danger of explosion if battery is incorrectly replaced. Replace only
with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the
manufacturer’s instructions.
The socket outlet shall be installed near the equipment and easily
accessible. The mains plug of the power supply cord shall remain
readily operable.
To completely disconnect this apparatus from the AC Mains,
disconnect the power supply cord plug from AC receptacle.
FCC Note:
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
≥Reorient or relocate the receiving antenna.
≥Increase the separation between the equipment and receiver.
≥Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
≥Consult the dealer or an experienced radio/TV technician for
help.
Any unauthorized changes or modifications to this equipment
would void the user’s authority to operate this device.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Responsible Party:
Panasonic Corporation of North America
One Panasonic Way
Secaucus, NJ 07094
Support Contact:
Panasonic Consumer Electronics Company
Telephone No.: 1-800-211-7262
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE SCREWS.
NO USER-SERVICEABLE PARTS
INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may be
of sufficient magnitude to constitute a risk of
electric shock to persons.
RQT9139
(ENG)
2
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
(Inside of product)
DMP-BD30PP_Book1.book
3 ページ
2008年1月29日 火曜日 午後1時46分
Getting started 11 Table of contents/Accessory information
Getting started
Settings
IMPORTANT SAFETY INSTRUCTIONS............ 2
Accessory information ..................................... 3
Disc and card information................................ 4
Connection ........................................................ 6
Control reference guide.................................... 9
Easy Setting..................................................... 10
Setting the television and amplifier/receiver
operation........................................................ 10
Changing settings with the on-screen
menu ....................................................18
Changing the unit’s settings.......................... 20
Reference
Getting started
Table of contents
Frequently asked questions........................... 23
Troubleshooting guide ................................... 24
Messages ......................................................... 27
Disc and card handling................................... 27
Maintenance .................................................... 27
Specifications.................................................. 28
Glossary........................................................... 29
Limited Warranty (ONLY FOR U.S.A. ) .......... 30
Limited Warranty (ONLY FOR CANADA) ...... 31
Product Service............................................... 31
Referencia rápida en español
(Spanish Quick Reference).............................32
Playback
Basic play (Playing video contents).............. 11
Different kinds of playback for BD-Video ..... 13
Chapter playback ............................................ 14
Playing still pictures ....................................... 14
Playing music .................................................. 16
Showing FUNCTIONS menu........................... 16
Linked operations with the TV (EZ SyncTM
“HDAVI ControlTM”) ....................................... 17
Index................................................................. 33
Accessory information
Please check and identify the supplied accessories. Use numbers indicated in parentheses when asking for replacement parts.
(Product numbers correct as of September 2007. These may be subject to change.)
Only for U.S.A.: To order accessories, refer to “Accessory Purchases” on page 30.
Only for Canada: To order accessories, call the dealer from whom you have made your purchase.
∏
∏
∏
∏
1 Remote control
(N2QAYB000184)
1 Audio/Video cable
(K2KA6BA00003)
2 Batteries
for remote control
1 AC power supply cord
(K2CB2CB00022)
≥For use with this unit only. Do not use
it with other equipment.
Also, do not use cords for other
equipment with this unit.
(ONLY FOR U.S.A. )
Product Registration Card
Please complete and return the included product registration card, or register via the Internet at: http://www.prodreg.com/panasonic/
The enclosed Canadian French label sheet corresponds to the English display on the front and back side of the unit.
Using remote control
Batteries
Insert so the poles (i and j) match those in
the remote control.
When closing the lid, insert it from the j
(minus) side.
R6/LR6, AA
≥Do not use rechargeable type batteries.
≥Do not mix old and new batteries.
≥Do not use different types at the same time.
≥Do not heat or expose to flame.
≥Do not leave the battery(ies) in an
automobile exposed to direct sunlight for a
long period of time with doors and windows
closed.
≥Do not take apart or short circuit.
≥Do not attempt to recharge alkaline or
manganese batteries.
≥Do not use batteries if the covering has been
peeled off.
Mishandling of batteries can cause electrolyte
leakage which can damage items the fluid
contacts and may cause a fire.
Remove batteries if the remote control is not
going to be used for a long period of time.
Store in a cool, dark place.
Use
Remote control signal sensor
30˚
20˚
20˚
30˚
7 m (23 feet) directly
in front of the unit
If you cannot operate the unit or other
equipment using the remote control after
changing the batteries, please re-enter the
codes (> 10, 26).
RQT9139
(ENG)
3
DMP-BD30PP_Book1.book
4 ページ
2008年1月29日 火曜日 午後1時46分
Getting started 11 Disc and card information
Disc and card information
Packaged discs
This chart shows the different type of retail/commercial discs you can use, and also includes the industry-standard logos that should appear on
the discs and/or packaging.
Type of media/
Logo
BD-Video
Features
High Definition (HD)
movie and music discs
Indicated as
Type of media/
Logo
[BD-V]
DVD-Video
CD
Features
High quality movie and
music discs
Compact Discs (CD’s)
that contain audio and
music
≥Operation and sound
quality of CDs that do
not conform to CD-DA
specifications (copy
control CDs, etc.)
cannot be guaranteed.
Indicated as
[DVD-V]
[CD]
Recorded discs
This chart shows the different type of discs recorded with DVD recorders, DVD video cameras, personal computers, etc. that you can use.
Finalized
This mark means you must finalize the disc with the DVD recorder, etc. before playback. For details about finalizing, refer to
the operating instructions for your equipment.
Type of media/
Logo
Formats
Indicated as
Type of media/
Logo
Formats
Indicated as
BD-RE
≥Version 3 of the BD-RE
Recording Format
≥JPEG format
[BD-V]
DVD-R DL
Finalized
[DVD-V]
[DVD-VR]
[JPEG]
≥DVD-Video Format
≥Version 1.2 of the DVD
Video Recording
Format
≥AVCHD format
≥+VR (+R/+RW Video
Recording) Format
≥AVCHD format
[DVD-V]
BD-R
DVD-RAM
DVD-R/RW
Finalized
≥Version 2 of the BD-R
Recording Format
[BD-V]
≥Version 1.1 of the DVD
Video Recording
Format
≥JPEG format
≥AVCHD format
[DVD-VR]
≥DVD-Video Format
≥Version 1.1 of the DVD
Video Recording
Format
≥AVCHD format
[DVD-V]
[DVD-VR]
[JPEG]
[AVCHD]
[AVCHD]
rR/rRW/
rR DL
Finalized
[AVCHD]
[AVCHD]
≥CD-DA format
[CD]
≥MP3 format
[MP3]
≥JPEG format
[JPEG]
Finalized
≥It may not be possible to play the above discs in some cases due
to the type of discs, the condition of the recording, the recording
method and how the files were created.
≥When a disc recorded in the AVCHD format is being played, the
video may be paused for a few seconds at portions spliced, due
to deletion or editing.
CD-R/RW
SD cards
This chart shows the different type of cards recorded with Panasonic High Definition Video Camera or personal computers, etc. that you can use.
≥A miniSD Card and a microSD Card must be used with
Type of media
Formats
Indicated as
the attached adaptor that comes with the card.
≥JPEG format
[JPEG]
≥Useable memory is slightly less than the card capacity.
SD Memory Card§
≥AVCHD format
[AVCHD]
≥If the SD card is formatted on a PC, you may not be able
(from 8 MB to 2 GB)
to use it on this unit.
SDHC Memory Card
≥We recommend using a Panasonic SD card.
(from 4 GB to 16 GB)
≥Keep the Memory Card out of reach of children to
§
prevent swallowing.
Including miniSD Card and microSD Card
≥When a card recorded in the AVCHD format is being played, the
≥When using from 4 GB to 16 GB SD cards, only SD cards that
video may be paused for a few seconds at portions spliced, due to
display the SDHC logo can be used.
deletion or edition.
≥This unit is compatible with SD Memory Cards that meet SD Card
≥Switch the write-protect switch to the “LOCK” position to protect
Specifications FAT 12 and FAT 16 formats, as well as SDHC
the content from accidental erasure.
Memory Cards in FAT 32 format.
ADAPTER
RQT9139
(ENG)
4
≥In these operating instructions, the cards shown in the table
(D above) are comprehensively called SD cards.
DMP-BD30PP_Book1.book
5 ページ
2008年1月29日 火曜日 午後1時46分
Getting started 11 Disc and card information
≥Enjoy Final Standard Profile functions (> 13), such as picture-in-picture. The various functions differ depending on the disc.
≥When playing a set of two BD-Video discs, once the first disc finishes playing, the menu screen may continue to display even if the disc has
been ejected.
≥Regarding high specification audio (7.1ch) of BD-Video such as Dolby Digital Plus, Dolby TrueHD, DTS-HD High Resolution Audio and
DTS-HD Master Audio (> 21)
– they can be reproduced in the original format only when connected to a compatible amplifier/receiver with a HDMI AV OUT terminal (> 7) and
when “BD-Video Secondary Audio” is set to “Off” and “Bitstream” is selected in each format.
– they are output only as Dolby Digital bitstream when “BD-Video Secondary Audio” is set to “On” even when the unit is connected using the
HDMI AV OUT terminal.
– they are output only as Dolby Digital or DTS bitstream (depending to the original format) when the unit is connected using the DIGITAL AUDIO
OUT terminal.
Getting started
Regarding BD-Video
Note about using a DualDisc
The digital audio content side of a DualDisc does not meet the technical specifications of the Compact Disc Digital Audio (CD-DA) format so play
may not be possible.
Tips for making MP3/JPEG files
File format
MP3
Playable media
CD-R/RW§1
JPEG
CD-R/RW§1, DVD-RAM§2, BD-RE§3, SD card
Extension
Files must have the extension “.mp3” or “.MP3”.
Files must have the extension “.jpg” or “.JPG”.
Picture resolution
—
between 34k34 and 5120k3840 pixels
(sub sampling is 4:2:2 or 4:2:0)
Bit rates
32 kbps to 320 kbps
—
Sampling frequency
44.1 kHz/48 kHz
—
Reference
ID3 tags: version 1, 2.2, 2.3, 2.4
ID3 is a tag embedded in MP3 track to provide information
about the track.
This unit supports the versions listed above but only titles
and the names of artists can be displayed.
≥If there is a large amount of still picture data etc. within a
MP3 file, play may not be possible.
≥MOTION JPEG: not supported
≥SD card: JPEG conforming DCF§4 (Design rule for
Camera File system)
Thawing Time: approx. 2 sec. (7M pixels)
≥English alphabet and Arabic numerals are displayed correctly. Other characters may not be displayed correctly.
≥The display order on this unit may differ from how the order is displayed on a computer.
≥Depending on how you create the media (writing software), files and folders may not play in the order you numbered
them.
≥This unit is not compatible with packet-write format.
≥Depending on the recording conditions, the media may not play.
≥Operation may take time to complete when there are many files and/or folders and some files may not display or be
playable.
§1
§2
§3
§4
ISO9660 level 1 or 2 (except for extended formats), Joliet
This unit is compatible with multi-session.
This unit is not compatible with packet writing.
Discs must conform to UDF 2.0.
Discs must conform to UDF 2.5.
Design rule for Camera File system: unified standard established by Japan Electronics and Information Technology Industries Association
(JEITA).
Structure of MP3 and still pictures (JPEG) folders
You can play MP3 and still pictures (JPEG) with this unit by making folders on disc as shown
(D right).
≥Folder structure created on a DVD-RAM, BD-RE or an SD card is not displayed.
e.g.
Root
P0000001.jpg
P0000002.jpg
001
002 Folder
P0000003.jpg
P0000004.jpg
P0000005.jpg
MP3 files and folders in CD-R/RW
Prefix with 3-digit numbers in the order you want to play them.
003 Folder
Still pictures (JPEG) in CD-R/RW
Files inside a folder are displayed in the order they were updated or taken.
When the highest level folders are “DCIM” folders, they are displayed first on the tree.
004 Folder
Order of play
P0000006.jpg
P0000007.jpg
P0000008.jpg
P0000009.jpg
P0000010.jpg
P0000011.jpg
P0000012.jpg
Discs that cannot be played
≥BD-RE with the cartridge
≥2.6 GB and 5.2 GB DVD-RAM
≥3.95 GB and 4.7 GB DVD-R for Authoring
≥DVD-RAM that cannot be removed from their cartridges
≥Version 1.0 of DVD-RW
≥+R 8 cm (3z), DVD-ROM, CD-ROM, CDV, SACD, Photo CD,
MV-Disc and PD
≥DVD-Audio
≥Video CD and SVCD
≥WMA discs
≥DivX discs
≥PAL discs
≥HD DVD
≥BD-Video discs recorded at a rate of 50 frame per second
≥Other discs that are not specifically supported
RQT9139
(ENG)
5
DMP-BD30PP_Book1.book
6 ページ
2008年1月29日 火曜日 午後1時46分
Getting started 11 Connection
Connection
From the list below, please choose the connection method that fits your TV viewing environment best.
≥If you connect to a television using an included Audio/Video cable > A
≥If you connect to an HDMI (> 29) compatible television >
B
≥If you connect to an HDMI compatible television and an HDMI compatible amplifier/receiver to enjoy surround sound > C (> 7)
≥For other connection methods, please see pages 7 and 8.
≥Do not place the unit on amplifiers or equipment that may become hot. The heat can damage the unit.
≥Do not connect through the video cassette recorder. Due to copy guard protection, the picture may not display properly.
≥Turn off all equipment before connection and read the appropriate operating instructions.
Conserving power
This unit consumes a small amount of power even when it is turned off (less than 1 W). To save power when the unit is not to be used for a long
time, unplug it from the household AC outlet.
Please use HIGH SPEED HDMI cables that have the HDMI logo (as shown on the cover). It is recommended that you use Panasonic’s
HDMI cable.
Recommended part number: RP-CDHG15 (1.5 m/4.9 ft.), RP-CDHG30 (3.0 m/9.8 ft.), RP-CDHG50 (5.0 m/16.4 ft.), etc.
Basic connections
A Connecting to a television with an Audio/Video cable
AUDIO IN
R
L VIDEO IN
Television
AUDIO/
VIDEO IN
Audio/Video cable
(included)
Cooling fan
≥Connect terminals of the same
color.
≥High
definition video cannot be
NOTE
output with this connection.
Use connection B, C or E (> 7)
for high definition video.
§
TIPS
Back of the unit
DIGITAL AUDIO COAXIAL COMPONENT VIDEO OUT
Y
PB
OUT
(PCM/BITSTREAM)
AUDIO OUT
L
FRONT L /L SURROUND CENTER
L
R
FRONT R /R
Please
connect
directly
to TV.
AC IN
PR
OPTICAL
S VIDEO OUT
AV OUT
AC power supply cord (included)
Connect only after all other
connections are complete.
R
VIDEO OUT
SUBWOOFER
2ch
5.1ch
With audio cables, connect the
AUDIO OUT terminals to the
two-channel audio input terminals of
an analog amplifier/receiver or
system component in place of a
television to enjoy stereo sound.
To improve picture quality
≥Use connections D or E (> 7).
To enjoy a richer sound
≥Use connections F or G (> 8).
(Unplug the red and white plugs.)
VIDEO OUT
2ch AUDIO OUT§
To a household AC outlet
(AC 120 V, 60 Hz)
B Connecting to an HDMI compatible television
You can enjoy high quality, digital video and audio.
HDMI IN
HDMI cable
NECESSARY SETTINGS
≥“HDMI Video Mode” and “HDMI
NOTE Audio Output” : “On” (> 22)
HDMI
compatible
television
Cooling fan
Back of the unit
DIGITAL AUDIO COAXIAL COMPONENT VIDEO OUT
Y
PB
OUT
(PCM/BITSTREAM)
OPTICAL
AV OUT
AC power supply cord (included)
Connect only after all other connections are
complete.
To a household AC outlet
(AC 120 V, 60 Hz)
RQT9139
(ENG)
6
FRONT L /L SURROUND CENTER
L
R
FRONT R /R
Please
connect
directly
to TV.
HDMI AV OUT
AC IN
AUDIO OUT
L
PR
S VIDEO OUT
VIDEO OUT
R
2ch
SUBWOOFER
5.1ch
To enjoy a richer sound
≥Use connections F or G (> 8)
TIPS additionally.
In this case, set “HDMI Video Mode”
to “On” and “HDMI Audio Output” to
“Off” (> 22).
With this connection, you can use
EZ Sync “HDAVI Control” (> 17).
DMP-BD30PP_Book1.book
7 ページ
2008年1月29日 火曜日 午後1時46分
Getting started 11 Connection
C Connecting to an HDMI compatible television and HDMI compatible amplifier/receiver
AC power supply cord
(included)
Connect only after all
other connections are
complete.
NECESSARY SETTINGS
≥“HDMI Video Mode” and “HDMI Audio Output” :
NOTE “On” (> 22)
≥“Speaker” : “Multi Channel” (> 22)
≥“Digital Audio Output” : Depending on the
connected amplifier/receiver (> 21)
HDMI
compatible
television
Multi channel speakers
HDMI OUT
HDMI IN
TIPS
HDMI cable
Back of the unit
DIGITAL AUDIO COAXIAL COMPONENT VIDEO OUT
Y
PB
OUT
(PCM/BITSTREAM)
AUDIO OUT
L
FRONT L /L SURROUND CENTER
L
R
FRONT R /R
Please
connect
directly
to TV.
HDMI AV OUT
AC IN
With this connection, you can use EZ Sync
“HDAVI Control” (> 17).
HDMI IN
HDMI compatible
amplifier/receiver
Getting started
When connected to a compatible amplifier/receiver, you can enjoy surround sound recorded with Dolby Digital Plus, Dolby TrueHD or
DTS-HD.
OPTICAL
AV OUT
PR
S VIDEO OUT
VIDEO OUT
R
2ch
SUBWOOFER
5.1ch
Cooling fan
To a household AC outlet
(AC 120 V, 60 Hz)
Connection methods for using other video terminals
D With S VIDEO OUT
The S VIDEO OUT terminal provides a more vivid picture than the VIDEO OUT terminal.
AUDIO IN
R
L
S VIDEO IN
≥High definition video cannot be output with
this connection.
NOTE Use connection B (> 6), C or E for high
definition video.
Television
≥Unplug the yellow plug of Audio/Video cable.
Audio/Video cable
(included)
S Video cable
Back of the unit
AUDIO OUT
DIGITAL AUDIO COAXIAL COMPONENT VIDEO OUT
Y
PB
OUT
(PCM/BITSTREAM)
L
FRONT L /L SURROUND CENTER
L
R
FRONT R /R
Please
connect
directly
to TV.
R
PR
OPTICAL
S VIDEO OUT
≥Actual video quality depends on the
television.
VIDEO OUT
SUBWOOFER
2ch
5.1ch
E With COMPONENT VIDEO OUT
You can enjoy high definition images by connecting to a component video terminals that supports 720p (750p) and 1080i (1125i) signals.
Television
AUDIO IN
R
L
COMPONENT
VIDEO IN
Component
Video cable
Audio/Video cable
(included)
Back of the unit
DIGITAL AUDIO COAXIAL COMPONENT VIDEO OUT
Y
PB
OUT
(PCM/BITSTREAM)
AUDIO OUT
L
FRONT L /L SURROUND CENTER
L
R
FRONT R /R
Please
connect
directly
to TV.
OPTICAL
PR
S VIDEO OUT
VIDEO OUT
≥Connect terminals of the same color.
≥Unplug the yellow plug of Audio/Video cable.
NOTE ≥Set “Black Level Control” to “Darker”. (> 20)
≥Some discs prohibit high definition video
output from COMPONENT VIDEO OUT
terminals. In this case, video resolution is
converted to 480p.
To enjoy high definition/progressive video
≥Connect to a television that supports 480p or
higher.
TIPS ≥Set “Component Video Resolution” to “480p”,
“720p” or “1080i”. (> 22)
≥Set “HDMI Video Mode” to “Off”. (> 22)
Otherwise, the video is output as 480i.
R
2ch
SUBWOOFER
5.1ch
RQT9139
(ENG)
7
DMP-BD30PP_Book1.book
8 ページ
2008年1月29日 火曜日 午後1時46分
Getting started 11 Connection
Connecting an amplifier/receiver (excluding HDMI connection)
F With 5.1ch AUDIO OUT
When connected to a compatible amplifier/receiver using the 5.1ch AUDIO OUT terminals, you can enjoy surround sound.
Multi channel speakers
NOTE ≥7.1 channel disc is mixed down to
O OUT
PB
5.1 channel audio.
AUDIO OUT
FRONT L /L SURROUND CENTER
L
L
NECESSARY SETTINGS
≥“Speaker” : “Multi Channel” (> 22)
!
Connect Audio
cables to
terminals
corresponding to
the speakers you
have connected.
When connected to an HDMI
compatible television (> 6, B)
≥“HDMI Audio Output” : “Off” (> 22)
(Otherwise, the sound is output from
the television.)
≥Depending on how the disc was
recorded, the audio may not be
output properly on the number of
channels desired.
"
PR
R
FRONT R /R
R
SUBWOOFER
2ch
5.1ch
Back of the unit
Amplifier/receiver with
5.1ch AUDIO IN
Cable connections
a Front speaker (L/R)
b Surround speaker (L/R)
c Center speaker
d Subwoofer
G With DIGITAL AUDIO OUT
You can enjoy surround sound, when connected to an amplifier/receiver using the COAXIAL or OPTICAL terminal.
With COAXIAL
Coaxial cable
COAXIAL IN
Back of the unit
L
FRONT L /L SURROUND CENTER
L
R
FRONT R /R
Please
connect
directly
to TV.
R
PR
OPTICAL
S VIDEO OUT
When connected to an HDMI
compatible television (> 6, B)
≥“HDMI Audio Output” : “Off” (> 22)
(Otherwise, the sound may not be
output with the desired settings.)
AUDIO OUT
DIGITAL AUDIO COAXIAL COMPONENT VIDEO OUT
Y
PB
OUT
(PCM/BITSTREAM)
VIDEO OUT
SUBWOOFER
2ch
5.1ch
Amplifier/receiver with a
built-in decoder or a
decoder-amplifier/
receiver combination
With OPTICAL
Optical digital
audio cable
OPTICAL IN
Back of the unit
DIGITAL AUDIO COAXIAL COMPONENT VIDEO OUT
Y
PB
OUT
(PCM/BITSTREAM)
AUDIO OUT
L
FRONT L /L SURROUND CENTER
L
Please
connect
directly
to TV.
OPTICAL
RQT9139
(ENG)
8
PR
S VIDEO OUT
VIDEO OUT
R
R
2ch
FRONT R /R
SUBWOOFER
5.1ch
NECESSARY SETTINGS
≥“Digital Audio Output” : Depending
NOTE on the connected amplifier/receiver
(> 21)
Amplifier/receiver with a
built-in decoder or a
decoder-amplifier/
receiver combination
DMP-BD30PP_Book1.book
9 ページ
2008年1月29日 火曜日 午後1時46分
Getting started 11 Control reference guide
! Turn the unit on and off (> 10)
@ TV operation buttons (> 10)
You can operate the TV through the unit’s remote control.
[Í TV POWER] : Turn the television on and off
[TV/VIDEO] : Switch the input channel
[W X CH] : Channel select
[i j VOL] : Adjust the volume
# Open or close the disc tray (> 11)
$ Numbered buttons
Select title numbers, etc./Enter numbers (> 12)
% Cancel
^ Basic playback control buttons (> 11, 12)
& Show status messages (> 12)
* Show Pop-up menu (> 13)
( Show Top menu/Direct Navigator (> 11)
AJ Show sub menu (> 14)
AA These buttons are used when operating a BD-Video disc that
includes JavaTM applications (BD-J). For more information about
operating this kind of disc, please read the instructions that came
with the disc.
The [A] and [B] buttons are also used with the “Title View”, “Picture
View” and “Album View” screens (> 14).
AB Show Setup menu (> 20)
AC Switch on/off Secondary Video (Picture-in-picture) (> 13)
AD Transmit the remote control signal
AE Receiver operation buttons (> 10)
You can operate an amplifier/receiver through the unit’s remote
control.
[i j VOL] : Adjust the volume
[MUTING] : Mute the sound
AF Reproduce more natural audio (> 12)
AG Select audio (> 12)
AH Show FUNCTIONS menu (> 16)
AI Selection/OK, Frame-by-frame (> 12)
BJ Show on-screen menu (> 18)
BA Return to previous screen
BB Select disc drive or SD card drive (> 11)
BC Switch on/off Secondary Audio (> 13)
POWER
POWER
OPEN/CLOSE TV/VIDEO CH
VOL
RECEIVER
VOL
MUTING
RE-MASTER
CANCEL
AUDIO
SKIP
PAUSE
PLAY
STATUS
FUNCTIONS
-UP MENU
POP
PLAY
OK
SUB MENU
19
RETURN
1
!
S
A
B
SETUP
PIP
DIS
STOP
DIRECT NAVIGATO
R
TOP MENU
.
SLOW/SEARCH
C
CAUTION
Do not place objects in front of the unit. The disc tray may collide
with objects when it is opened, and this may cause injury.
D
SECONDARY
AUDIO BD/SD
Getting started
Control reference guide
1
1
PULL-OPEN
SD CARD
1 POWER button (POWER Í/I) (> 10)
Press to switch the unit from on to standby mode or vice versa. In
standby mode, the unit is still consuming a small amount of power.
2 Disc tray (> 11)
3 SD Card LED
≥It is possible to set the LED to turn on/off. (> 21, SD Card LED
Control)
4 SD card slot (> 14)
5 Display
Disc indicator
SD card indicator
The indicator blinks when reading data from a disc or card.
Pull to flip down the
front panel.
6 Search/Slow-motion/Skip (> 12)
Search:
Press and hold (During play)
Slow-motion: Press and hold (During pause)
Skip:
Press
7 Open or close the disc tray (> 11)
8 Remote control signal sensor (> 3)
9 Stop (> 12)
: Pause (> 12)
; Start play (> 11)
Rear panel terminals (> 6–8)
RQT9139
(ENG)
9
DMP-BD30PP_Book1.book
10 ページ 2008年1月29日 火曜日 午後1時46分
Getting started 11 Easy Setting/Setting the television and amplifier/receiver operation
Easy Setting
After connecting your new player and pressing the power button, a screen for the basic settings will appear.
Preparation
Turn on the television and select the appropriate video input on the
television.
1 Press [Í BD POWER].
Setup screen appears.
≥If this unit is connected to a Panasonic TV (VIERA)
supporting HDAVI Control 2 via an HDMI cable, then the
“On-screen Language” and “TV Aspect” setting information
on the TV are captured from the TV.
≥You can perform this setup anytime
by selecting “Easy Setting” in the
TIPS Setup menu. (> 20)
≥You can also change these settings
individually. (> 21)
POWER
2 Follow the on-screen instructions and make
the settings with [3, 4] and [OK].
OK
“On-screen Language” and “TV Aspect” (> 21) are set.
Setting the television and amplifier/receiver
operation
You can operate the TV or amplifier/receiver using the unit’s remote control.
Point the remote control at the television or amplifier/receiver.
1 For televisions
Input the 4-digit code with the numbered buttons while pressing
[Í TV POWER].
For amplifiers/receivers
Input the 4-digit code with the numbered buttons while pressing
[MUTING].
e.g., 0001: [0] B [0] B [0] B [1]
2 Test by turning on the television or adjusting the volume of the
amplifier/receiver.
Brand
TV Code
Panasonic
0051/0055/0250/0650
ADVENT
0761/0783/0815/0817/0842
AKAI
0030/0098/0672/0702/0812
AMERICA ACTION 0180
AOC
0003/0019/0030/0052/0137/0185
APEX DIGITAL
0748/0765/0767/0879/0890
0003/0092/0180/0451/0623/0802/0875/
AUDIOVOX
1937
AXION
1937
BANG & OLUFSEN 0620/1620
BROKSONIC
0003/0236/0463
CASIO
0611/1205
0019/0039/0066/0067/0091/0092/0451/
DAEWOO
0623/0661/0672/1661
0019/0038/0039/0154/0158/0171/0177/
EMERSON
0178/0179/0180/0181/0182/0183/0185/
0236/0270/0280/0282/0463/0623
ENVISION
0030/0813
EPSON
0833/0840
FISHER
0154/0159
FUJITSU
0179/0186/0683/0809/0853
0021/0027/0029/0047/0051/0055/0135/
0138/0174/0178/0251/0279/0282/0451/
GE
0747/1347/1447
0019/0030/0032/0106/0178/0317/0409/
GOLDSTAR
0442/0457/0700/0856/1178/1265
GO VIDEO
0886
HAIER
0768/1034
HANNSPREE
1348/1351/1352
HEWLETT
1088/1089/1101/1494/1502
PACKARD
HISENSE
0748
0016/0032/0038/0056/0095/0097/0145/
HITACHI
0151/0173/0227/0279/0409/0413/1145
INFOCUS
0736/0738/0741/0752/0781/1164/1516
0036/0053/0069/0160/0169/0182/0731/
JVC
1253
KLH
0765/0767
0019/0030/0032/0106/0178/0317/0409/
LG
0442/0457/0700/0856/1178/1265
LOEWE
0136
0020/0024/0028/0030/0036/0054/0096/
0179/0186/0187/0230/0386/0706/0802/
RQT9139 MAGNAVOX
1254/1454
(ENG)
MARANTZ
0030/0054/0444/0704/0854/0855/1154
MEMOREX
0016/0106/0150/0154/0178/0179/0463
10
Brand
≥If your television or amplifier/
receiver brand has more than one
code listed, select the one that
NOTE allows correct operation.
≥If your television or amplifier/
receiver brand is not listed or if the
code listed for them does not allow
control of your television or
amplifier/receiver, this remote
control is not compatible with them.
Use their remote control.
≥When audio is muted, press
[MUTING] again.
TV Code
0014/0019/0093/0098/0150/0155/0178/
MITSUBISHI
0331/0358/0836/0868/1250
NORCENT
0748/0824/1089
OPTOMA
0887
ORION
0179/0236/0463/1463
PHILIPS
0054/0690/1154/1454
0020/0024/0028/0030/0036/0054/0096/
PHILIPS
0179/0186/0187/0230/0386/0706/0802/
MAGNAVOX
1254/1454
0054/0690/1154/1454
PIONEER
0038/0166/0172/0679/0866
0765/0865/1262/1276/1314/1316/1326/
POLAROID
1327/1328/1341/1498/1523
PROSCAN
0047/0747/1347/1447
PROVIEW
0835/1401/1498
0018/0019/0029/0038/0047/0090/0135/
RCA
0174/0278/0679/0747/1047/1147/1247/
1347/1447/1547
RUNCO
0017/0030/0251/0497/0603
SAMPO
0030/0032/0039/0052/0100/0110/1755
0019/0030/0032/0056/0060/0178/0329/
SAMSUNG
0408/0427/0587/0702/0766/0812/0814/
1060
SANSUI
0463
0088/0107/0146/0154/0159/0232/0484/
SANYO
0799/0893
0039/0093/0153/0157/0165/0220/0281/
SHARP
0386/0398/0491/0688/0818/0851
0000/0011/0080/0111/0273/0353/0810/
SONY
0834/0867/1100
SVA
0587/0748/0768/0865/0870/0871/0872
0020/0028/0030/0054/0065/0096/0171/
SYLVANIA
0381
SYMPHONIC
0171/0180
SYNTAX-BRILLIAN 1007/1144/1240/1255/1257/1258/1331
TATUNG
0003/0049/0055/0396/1101/1756
THOMSON
0209/0210/0047
0036/0060/0149/0154/0156/0650/0832/
TOSHIBA
0845/1156/1164/1256/1265/1356/1656/
1704
ULTRA
0391
VIEWSONIC
0857/0864/0885/1755
WESTINGHOUSE 0885/0889/0890/1282/1577
YAMAHA
0019/0030/0769/0833/0839
ZENITH
0016/0017/0092/0178/0463/1265
Brand
Amplifier
Code
Panasonic
0308
TECHNICS
BOSE
0308
0674
DENON
HARMAN
KARDON
KENWOOD
KLH
LINN
MARANTZ
MCINTOSH
NAD
ONKYO
0251
PHILIPS
PIONEER
0823
QUASAR
RCA
0823
SAMSUNG
SANYO
SHARP
SHERWOOD
SONY
TEAC
TOSHIBA
YAMAHA
0815/
1126
0354
Receiver Code
1308/0039/0367/1641/2001/
2002
1308/0039/0208
1229/0639/1253/1933
1360/0004/0121/0273/1142/
1306/1311
0110/0189/1289/1306
0110/0189/1289/1306
1313/0027/0042/0077/0186
1390/1412/1428
0189
1189/1269/0039/0189/0128/
1120/1289
1289
0320
0135/0380/1298/1320
1189/1269/0189/0391/1120/
1266/1368
1023/0150/0244/0531/0630/
1343/1384
0039
1023/1609/1254/0054/0530/
0531/1074/1390/1511
1295
1251/1469/1801
0186/1361
0491/0502/1077/1423/1517/
1653
1622/0158/0168/0474/1367/
1529/1658/1758
0463/1074/1390
0135
1023/0176/0186/1331
DMP-BD30PP_Book1.book
11 ページ 2008年1月29日 火曜日 午後1時46分
Playback 11 Basic play (Playing video contents)
Basic play (Playing video contents)
Instructions for operations are generally described using the remote control in these operating instructions.
VIDEO1
Getting started
Preparation
Turn on the television and select the appropriate video input on the television.
POWER
POWER
OPEN/CLOSE TV/VIDEO CH
VOL
RECEIVER
VOL
MUTING
RE-MASTER
CANCEL
AUDIO
SLOW/SEARCH
STOP
PAUSE
Playback
SKIP
PLAY
STATUS
FUNCTIONS
PLAY
DIS
DIRECT NAVIGATO
R
TOP MENU
-UP MENU
POP
OK
SUB MENU
RETURN
S
A
SETUP
B
C
D
PIP SECONDARY
AUDIO BD/SD
1 Press [Í BD POWER] to turn on the unit.
2 Press [< OPEN/CLOSE] to open the
e.g.,
disc tray and load the disc.
≥DISCS CONTINUE TO ROTATE WHILE MENUS
ARE DISPLAYED. Press [∫] when you have
NOTE finished playback to protect the unit’s motor, your
television screen and so on.
≥Press the button again to close the tray.
≥Load double-sided discs so the label for the side
you want to play is facing up.
≥DVD-RAM: Remove discs from their cartridges before use.
Play starts.
≥If a disc with data in different file formats is inserted, the file selection
menu is displayed. Press [3, 4] to select the desired file format and
press [OK].
≥If play does not start, press [1] (PLAY).
e.g., [BD-V]
e.g., [DVD-VR]
DIRECT NAVIGATOR Title View
DVD-RAM(VR)
5
1
2
3
No.
01
02
03
04
05
06
07
08
09
10
Rec. Length
0:15 (SP)
4
Date
9/ 5
9/ 5
9/ 5
9/ 6
9/ 6
9/ 6
9/ 7
9/ 7
9/ 7
9/ 7
To switch drives
Press [BD/SD] to select “BD” to play a disc.
TIPS ≥If a disc or an SD card is inserted while the unit is
stopped, the drive switches automatically
depending on the inserted media.
To display menus
[BD-V] [AVCHD] [DVD-VR] [DVD-V]
Press [TOP MENU/DIRECT NAVIGATOR].
≥The producers of the disc can control how discs are
played. So you may not always be able to control
play as described in these operating instructions.
Read the disc’s instructions carefully.
Video Picture
Day
Wed
Wed
Wed
Thu
Thu
Thu
Fri
Fri
Fri
Fri
Channel
IN 2
IN 2
VHS
VHS
IN 2
IN 2
Start
10:00AM
11:30AM
11:59PM
10:00AM
11:30AM
11:59PM
10:00AM
10:30AM
11:30AM
11:59PM
Title Name
≥You can play data in AVCHD format recorded on an
SD card.
Page 01/02
SUB
MENU
Previous
Play
RETURN
A Video
Next
B Picture
≥ If the menu is displayed, press [3, 4, 2, 1] to select the item and press
[OK].
≥If the screen prompting you to use the color buttons appears, continue to
operate with the color buttons on the remote control.
TIPS
RQT9139
(ENG)
11
DMP-BD30PP_Book1.book
12 ページ 2008年1月29日 火曜日 午後1時46分
Playback 11 Basic play (Playing video contents)
Other operations during play (These functions may not work depending on the disc.)
STOP
STATUS
Stop
The stopped position is memorized.
Resume play function
Press [1] (PLAY) to restart from this position.
≥The position is cleared if the tray is opened or you press [∫]
several times to display “STOP” on unit’s display.
PAUSE
Status messages
The status messages give you information about what is currently
being played. Each time you press [STATUS], the information
displayed will change.
Type of disc
Play status
e.g. [BD-V]
BD-Video
Pause
Play
≥Press [;] again or [1] (PLAY) to restart play.
SLOW/SEARCH
Search/Slow-motion
The speed increases up to 5 steps.
≥Press [1] (PLAY) to revert to normal playback speed.
≥For some discs, the speed may not change.
Search
While playing, press [6] or [5].
≥Press and hold [:/6] or [9/5] on the main unit.
≥[BD-V] [AVCHD] [DVD-VR] [DVD-V]:
Audio is heard during first level of forward search.
≥[CD] [MP3]: The speed is fixed to a single step.
Slow-motion
While paused, press [6] or [5].
≥Press and hold [:/6] or [9/5] on the main unit.
≥[BD-V] [AVCHD]: Forward direction [5] only.
≥[DVD-VR]:If continued for approx. 5 minutes, slow-motion play
pauses automatically.
SKIP
Skip
Skip to the title, chapter or track you want to play.
≥Each press increases the number of skips.
T: Title
C: Chapter
No display
PL: Playlist
Items change depending on the disc
played.
Elapsed time in the title
v T1
C1
0:05.14
0:20.52
Current position
Depending on the kind of disc or the playback status,
this display may not appear.
AUDIO
Changing audio during play
[BD-V] [AVCHD] [DVD-V]
e.g. [DVD-V]
Soundtrack
Starting from a selected item
Play starts from the selected title or chapter.
[BD-V] [AVCHD]
[DVD-V]
e.g., 5: [0] B [0] B [5]
e.g., 5: [0] B [5]
15: [0] B [1] B [5]
15: [1] B [5]
≥While stopped (the image on the right is
displayed on the screen), the title is
designated. While playing, the chapter is
designated.
Total time
1 ENG
§Digital 3/2.1ch
English is selected.
You can change the audio channel number each time you press
the button. This allows you to change the soundtrack language
(> 18, Soundtrack), etc.
[DVD-VR]
AudioLR>AudioL>Audio R
^---------------------------------}
DVD-RAM(VR)
Play
“AudioLR” is
selected
RE-MASTER
AudioLR
Reproducing more natural audio
(Discs recorded at 48 kHz or less)
This feature gives you a more natural sound by adding higher
frequency signals not recorded on the track.
OK
Frame-by-frame
While paused, press [2] (2;) or [1] (;1).
Each press shows the next frame.
≥Press and hold to change in succession forward or backward.
≥Press [1] (PLAY) to revert to normal playback speed.
≥[BD-V] [AVCHD]: Forward direction [1] (;1) only.
Screen Aspect
RQT9139
(ENG)
12
When black bars are shown at the top, bottom, left, and right sides
of the screen, you can enlarge the image to fill the screen.
1 Press [SUB MENU].
2 Press [3, 4] to select “Screen Aspect” and press [OK].
3 Press [2, 1] to select “Side cut” or “Zoom”.
Normal: Normal output
Side cut: The black bars on the right and left sides of the 16:9
image disappear and the image is enlarged. Please note
that the right and left sides of the image are cut off when
the black bar is not displayed.
Zoom: The black bars on the top and bottom sides of the 4:3
image disappear and the image is enlarged. Please note
that the top and bottom sides of the image are cut off
when the black bar is not displayed.
≥When “TV Aspect” (> 21) is set to “4:3 Pan & Scan” or “4:3
Letterbox”, the “Zoom” effect is disabled.
Press [RE-MASTER] to select “Re-master 1”,
“Re-master 2” or “Re-master 3”.
Select the one that you like best.
Other types of
When playing LPCM sound
sound
Type of music
Effect level
High tempo (e.g., pop and
Re-master 1
Light
rock)
Re-master 2 Various tempos (e.g., jazz)
Medium
Re-master 3 Low tempo (e.g., classical)
Strong
Off
Off
Off
Setting
≥This function is effective for audio from the HDMI terminal or the
DIGITAL AUDIO OUT terminal only when “Digital Audio Output”
is set to “PCM”. (However, in this case, audio is output as 2ch
from the DIGITAL AUDIO OUT terminal.)
DMP-BD30PP_Book1.book
13 ページ 2008年1月29日 火曜日 午後1時46分
Playback 11 Different kinds of playback for BD-Video
Different kinds of playback for BD-Video
[BD-V]
Some discs permit a variety of interactive functions in addition to the ordinary playback operation.
Showing Pop-up menu
The Pop-up menu is a special feature available with some BD-Video discs. This menu may vary with discs. For the operating method, refer to
the instructions for the disc.
1 Press [POP-UP MENU].
2 Press [3, 4, 2, 1] to select
the item and press [OK].
e.g.,
≥Pop-up menu also appears by pressing
[SUB MENU] and selecting “Pop-up Menu”.
TIPS
Previous
To exit the screen
≥Press [POP-UP MENU].
Next
≥The Final Standard Profile [“Picture-in-picture”, “Virtual Package” (> below), etc.] is a new playback function of BD-Video. Contents of
playback and the operating method may vary with the disc. For details, refer to the instructions for the disc.
Secondary video can be played from a disc compatible with the picture-in-picture
function.
For the playback method, refer to the instructions for the disc.
Secondary video
≥Only the primary video is played during search/
slow-motion or frame-by-frame.
NOTE
To turn on/off secondary video
Playback
Playing secondary video (picture-in-picture) and secondary audio
Press [PIP].
Secondary video is played.
≥“PiP ON” is displayed.
≥Press the button to turn it ON and OFF.
To turn on/off audio with the secondary
video
Press [SECONDARY AUDIO].
Primary video
The secondary audio is played.
≥“Secondary Audio ON” is displayed.
≥Press the button to turn it ON and OFF.
Virtual package
For a disc compatible with the virtual package (> 29), data is copied to other media
(> 29, Local storage) from the disc to use the different functions while playing the
data.
For this unit, data is copied to an SD card.
The methods for copy and playback and the required available capacity on the card
may vary with the disc. For details, refer to the instructions for the disc.
NOTE
To use the above functions, it is recommended that you format the card on this unit.
Format the card using the following procedures. BD-Video data, such as secondary
video recorded on the card, can also be erased with the following procedures.
Formatting SD cards/Deleting data
1 Insert an SD card (> 14).
2 Press [FUNCTIONS].
3 Press [3, 4] to select “Other Functions” and press [OK].
TIPS
4 Press [3, 4] to select “Card Management” and press
[OK].
5 Press [3, 4] to select “BD-Video
Data Erase” or “Format SD Card”
and press [OK].
6 Press [2, 1] to select “Yes” and
NOTE
press [OK].
7 Press [2, 1] to select “Start” and
press [OK].
Card Management
SD card
Format SD Card
RETURN
≥If an SD card with files in different formats is
used, images and audio may not play back
properly. It is recommended that you use an SD
card with no data or an SD card formatted on this
unit.
No. of Files 6
Free space 300 MB
BD-Video Data Erase
OK
≥If the SD card is removed from this unit when
using data that was copied with the virtual
package function, disc playback stops.
≥Images and audio may freeze momentarily
during playback.
≥Data cannot be copied in the following cases.
– The card is protected.
– Available capacity on the card is too small.
Delete unnecessary data or use a new card.
≥When the function fails to work properly, even if
the data is copied, format the card again with this
unit. (In this case, all data will be erased.)
Format this SD Card.
≥It is impossible to restore data after formatting
the card or erasing the data.
Once a card is formatted, all data including those
recorded on the PC is erased as well, even if the
data were protected with other equipment.
Confirm whether the card can be formatted.
RQT9139
(ENG)
13
DMP-BD30PP_Book1.book
14 ページ 2008年1月29日 火曜日 午後1時46分
Playback 11 Chapter playback/Playing still pictures
Chapter playback
[DVD-VR]
1 Insert a disc (> 11).
2 While “Title View” screen is displayed
Press [3, 4] to select the title and press [SUB MENU].
To display the title properties
(recording date, etc.)
To select the chapter
Properties
View Chapters
To picture
Playing still pictures (B below)
3 Press [3, 4] to select “View Chapters” and press [OK].
4 Press [2, 1] to select the chapter and press [OK].
Playing still pictures
[JPEG]
You can play still pictures recorded onto a BD-RE, DVD-RAM, CD-R/RW and an SD card.
1 Insert a disc (> 11) or an SD card
(B right).
≥If a disc or an SD card containing
data in different file formats is
inserted, the file selection menu may
be displayed.
SD card:
Press [3, 4] to select “Picture
(JPEG) Navigator” and press [OK].
CD-R/RW:
Press [3, 4] to select “Pictures”
and press [OK].
e.g.,
Inserting a card
e.g.,
SD Card
Picture (JPEG) Navigator
SUB
MENU
OK
CD-R/RW, SD card
“Album View” screen is displayed
e.g.,
“Picture View” screen is displayed
B Go to step 3
e.g.,
Album View
DVD-RAM(VR)
Video
Picture
Insert the card label up with the
cut-off corner on the right.
1 Pull to flip down the front panel.
2 Insert the SD card into the SD card slot.
≥Press on the center of the card until it clicks into
place.
RETURN
BD-RE, DVD-RAM
DIRECT NAVIGATOR
Playback HD Movie (AVCHD)
Select an action or press [RETURN].
Removing the card
Press on the center of the card and pull it straight out.
Picture View
Pictures
CD(JPEG)
ᧂ
106_DVD
Total 8
penguin_jpg
2006 9 12
Total 13
Page 02/02
Previous
OK
SUB
MENU
RETURN
A Video
Next
001
002
003
004
005
006
007
008
TIPS
009
To return to the previous screen
Press [RETURN].
To exit the screen
Press [DIRECT NAVIGATOR].
Slideshow
Press [OK] to go to Picture View
B Picture
From SUB MENU you can select a folder.
≥When the “Title View” screen is
displayed, press the [B] button to
switch to the “Album View”
screen.
SUB
MENU
Page 01/01
Play
RETURN
CD-R/RW
2 Press [3, 4, 2, 1] to select the album and press [OK].
Discs containing data in different file formats.
To switch from the MP3 menu to JPEG menu,
perform steps below.
1 Press [FUNCTIONS].
2 Press [3, 4] to select “Menu” and press [OK].
3 Press [3, 4] to select “Pictures” and press [OK].
e.g.,
DIRECT NAVIGATOR
Picture View
DVD-RAM(VR)
Video
Picture
2006 9 12
0001
0002
0003
0004
0005
0006
0007
0008
≥Small-sized still pictures are displayed with a frame.
0009
Page 001/001
SUB
MENU
Play
RETURN
3 Press [3, 4, 2, 1] to select the still picture and press
[OK].
RQT9139
(ENG)
14
≥Press [2, 1] to display the previous or next still
picture.
≥Press [:, 9] to show other pages.
NOTE
DMP-BD30PP_Book1.book
15 ページ 2008年1月29日 火曜日 午後1時46分
Playback 11 Playing still pictures
Useful functions during still picture play
Start Slideshow
To select the still pictures in another folder
You can display still pictures one by one at a constant interval.
BD-RE, DVD-RAM
BD-RE, DVD-RAM
To switch to another higher folder
(Only if there is a multiple number of higher folders recognizable)
1 While the “Album View” screen is displayed
Press [SUB MENU].
2 Press [3, 4] to select “Select Root folder” and press [OK].
≥You can also start slideshow by pressing [1] (PLAY) after
selecting the album.
Select Root folder
Changes the Album folder to be accessed.
CD-R/RW, SD card
1 While the “Picture View” screen is displayed
Press [SUB MENU].
2 Press [3, 4] to select “Start Slideshow” and press [OK].
To stop slideshow
Press [∫].
Slideshow with music
SD card only
\DCIM
Press [OK] to confirm
OK
3 Press [2, 1] to select the higher folder and press [OK].
CD-R/RW
1 While the “Picture View” screen is displayed
Press [SUB MENU].
2 Press [3, 4] to select “Select Folder” and press [OK].
3 Press [3, 4] to select a folder and press [OK].
The “Picture View” screen for the folder appears.
If a music CD is inserted in the disc tray while playing slideshows,
the music CD starts playing automatically as background music.
Pictures
CD(JPEG)
≥You cannot search or skip on a music CD.
≥When the slideshow stops, playback of the music CD also stops.
Folder selection
021216_0026
001
002
003
004
005
006
007
008
009
010
Slideshow settings
103
104
105
OK
RETURN
In step 2 in “Start Slideshow” above,
1 Press [3, 4] to select “Slideshow settings” and press [OK].
2 To change the display interval
Press [3, 4] to select “Display Interval” and press [2, 1] to
select the interval (“Long”, “Normal” or “Short”).
≥When a still picture with large number of pixels is played, the
display interval may become longer. Even if the setting is
changed, the display interval may not become shorter.
To repeat slideshow
Press [3, 4] to select “Repeat Play” and press [2, 1] to select
“On” or “Off”.
3 Press [3, 4, 2, 1] to select “Set” and press [OK].
Rotate
F 7/25
Playback
1 While the “Album View” screen is displayed
Press [3, 4, 2, 1] to select the album and press
[SUB MENU].
2 Press [3, 4] to select “Start Slideshow” and press [OK].
To show the picture properties
While playing
Press [STATUS] twice.
e.g. JPEG on DVD-RAM
Shooting date
Folder - picture No.
Photo 11/12/2007
102 - 0001
Total
3/9
To exit, press [STATUS].
1 While playing (except for slideshows)
Press [SUB MENU].
2 Press [3, 4] to select “Rotate Right” or “Rotate Left” and
press [OK].
≥The rotation information will be stored until the unit is turned off
or the media is removed.
Zoom out
This function is only available for small-sized still pictures.
1 While playing (except for slideshows)
Press [SUB MENU].
2 Press [3, 4] to select “Zoom out” and press [OK].
≥To cancel “Zoom out”, press [3, 4] to select “Zoom in” in step 2
and press [OK].
≥The zoom-out information will not be stored.
RQT9139
(ENG)
15
DMP-BD30PP_Book1.book
16 ページ 2008年1月29日 火曜日 午後1時46分
Playback 11 Playing music/Showing FUNCTIONS menu
Playing music
[CD] [MP3]
You can play generally available music CD or MP3 files recorded onto a CD-R/RW.
1 Insert a disc. (> 11)
≥If a disc containing data in different file formats is
inserted, the file selection menu may be displayed.
Press [3, 4] to select “MP3 Music” and press [OK].
CD
Pictures
MP3 Music
Select an action or press [RETURN].
SUB
MENU
≥Discs containing data in different file
formats.
switch from the JPEG menu to
TIPS To
MP3 menu, perform steps below.
1 Press [FUNCTIONS].
2 Press [3, 4] to select “Menu”
and press [OK].
3 Press [3, 4] to select “MP3
Music” and press [OK].
OK
RETURN
≥You can use search and skip
functions. (> 12)
≥When the “Screen Saver Function”
is set to “On” (> 21), the screen
switches to Screen Saver mode if
there is no operation for 10 minutes
after starting playback. (Playback
continues.)
2 Press [3, 4] to select the track and press [OK].
Play starts on the selected track.
e.g. [CD]
Music list
DIRECT NAVIGATOR
CD
“
” indicates the track currently playing.
No
01
02
03
04
05
0.09
4.30
Track1
5 Tracks / Total Play Time 20min54sec
Track Name
Play Time
4min30sec
Track1
3min41sec
Track2
Track3
4min30sec
Track4
3min11sec
5min 2sec
Track5
Play
RETURN
[MP3] Playing a track in another folder
1 While the “Music list” is displayed
Press [SUB MENU], press [3, 4] to select “Select Folder” and press [OK].
DIRECT NAVIGATOR
CD(MP3)
Select Folder
≥You cannot select folders that
contain no compatible tracks.
NOTE
MP3 music
001 My favorite
002 Brazilian pops
003 Chinese pops
004 Czech pops
005 Hungarian pops
006 Liner notes
007 Japanese pops
008 Mexican pops
009 Philippine pops
010 Swedish pops
011 Momoko
012 Standard number
013 Piano solo
014Vocal
F 7/25
Selected folder No. /Total folders
If the folder has no track, “– –” is
displayed as folder number.
To return to the previous screen
Press [RETURN].
TIPS
OK
RETURN
2 Press [3, 4] to select a folder and press [OK].
The “Music list” for the folder appears.
Playing music continuously even after turning off power to the television
When the unit is connected to a Panasonic TV (VIERA) that supports HDAVI Control 2 and
an amplifier/receiver, the power of the unit is turned off if the power to the television is
turned off, since “Power off link” (> 17) operates.
The following operations make it possible to keep the power of the unit ON and to play
music continuously.
1 While playing music
Press [SUB MENU].
2 Press [3, 4] to select “TV Power” and press [OK].
≥Sound may be discontinued for
several seconds when the power to
is turned off.
NOTE ≥Ifthethetelevision
operation mentioned left is
executed while audio is output from
the television, the sound may not be
output from the amplifier/receiver. It
is recommended to set the amplifier/
receiver beforehand so that audio
will be output from the amplifier/
receiver.
Showing FUNCTIONS menu
Some functions of this unit can be operated from the FUNCTIONS menu.
1 Press [FUNCTIONS].
≥Items to be displayed may vary with the media.
2 Press [3, 4] to select the item and press [OK].
≥Top Menu
≥Menu
≥Playback
≥SD card
≥BD/DVD/CD
≥Other Functions
RQT9139
(ENG)
16
e.g.,
BD Player FUNCTIONS
DVD-Video
Top Menu
Menu
Switches to the SD drive.
Switches to the disc drive.
“Setup” (> 20)
“Card Management” (> 13)
“Playlists”:
You can play playlists created on DVD-VR.
Press [3, 4, 2, 1] to select the playlist and press [OK].
SD card
Other Functions
OK
SUB
MENU S
RETURN
DMP-BD30PP_Book1.book
17 ページ 2008年1月29日 火曜日 午後1時46分
Playback 11 Linked operations with the TV (EZ SyncTM “HDAVI ControlTM”)
Linked operations with the TV
(EZ SyncTM “HDAVI ControlTM”)
What is EZ Sync “HDAVI Control”?
Preparation
1. Connect this unit to your TV or amplifier/receiver with an HDMI
cable (> 6–7).
2. Set “EZ Sync” to “On” (> 22).
(The default setting is “On”.)
3. Set the “HDAVI Control” operations on the connected equipment
(e.g., TV).
≥When using HDMI2 terminal of VIERA as “HDAVI Control”,
set the input channel to HDMI2 on VIERA.
4. Turn on all “HDAVI Control” compatible equipment and select this
unit’s input channel on the connected TV so that the “HDAVI
Control” function works properly.
Also when the connection or settings are changed, repeat
this procedure.
What you can do with “HDAVI Control”
Automatic input switching
Power off link
When the following operations are performed, the television will
automatically switch the input channel and display the
corresponding action.
– When play starts on the unit
– When an action that uses the display screen is performed
(e.g., Direct Navigator screen)
Power on link
When the television is off and the following operations are
performed, the television will automatically turn on and display the
corresponding action.
– When play starts on the unit
– When an action that uses the display screen is performed
(e.g., Direct Navigator screen)
All connected equipment compatible with “HDAVI Control”, including
this unit, automatically turns off when you switch the television off.
≥This unit automatically turns off even during playback or any
other operation.
Playback
EZ Sync “HDAVI Control” is a convenient function that offers
linked operations of this unit, and a Panasonic TV (VIERA) or
amplifier/receiver under “HDAVI Control”. You can use this
function by connecting the equipment with an HDMI cable. See
the operating instructions for connected equipment for
operational details.
≥EZ Sync “HDAVI Control”, based on the control functions provided
by HDMI which is an industry standard known as HDMI CEC
(Consumer Electronics Control), is a unique function that we have
developed and added. As such, its operation with other
manufacturers’ equipment that supports HDMI CEC cannot be
guaranteed.
≥This unit supports “HDAVI Control 2” function.
“HDAVI Control 2” is the standard (current as of February, 2007) for
Panasonic’s HDAVI Control compatible equipment. This standard is
compatible with Panasonic’s conventional HDAVI equipment.
≥It is recommended that you use Panasonic’s HDMI cable.
Recommended part number:
RP-CDHG15 (1.5 m/4.9 ft.), RP-CDHG30 (3.0 m/9.8 ft.),
RP-CDHG50 (5.0 m/16.4 ft.), etc.
≥Non-HDMI-compliant cables cannot be utilized.
Playing music continuously even after turning off
power to the television (> 16)
≥When [1] (PLAY) is pressed on this unit for “Automatic input
switching” or “Power on link”, the playback image is not
NOTE immediately displayed on the screen and it may not be
possible to watch the contents from where playback started.
In this case, press [:] or [6] to go back to where
playback started.
Easy control only with VIERA remote control
If you connect this unit to a TV that has “HDAVI Control 2” function
with an HDMI cable, you can operate this unit using the following
buttons on the TV remote control.
[3, 4, 2, 1], [OK], [RETURN], [SUB MENU] and colored buttons
Use the remote control for this unit to operate any other buttons
(numbered buttons, etc.) that are not listed above.
≥Refer to the TV operating instructions for operating TV.
Using the sub menu to operate
this unit
By using the TV remote control, you can play
discs using the “Control Panel” and display the
Top Menu (for BD-Video and DVD-Video) or
Pop-up Menu (for BD-Video).
1 Press [SUB MENU].
e.g.,
BD Player FUNCTIONS
1 Press the button for EZ Sync
on the remote control.
2 Select the player.
≥The FUNCTIONS menu is displayed.
DVD-Video
Control Panel
Screen Aspect
Top Menu
Pop-up Menu
This can also be displayed by using the
OK
SUB
VIERA menu screen.
RETURN
MENU
[Note] You cannot use the sub menu
while the Top Menu for BD-Video or DVD-Video is
displayed.
Using the FUNCTIONS menu to operate this unit
By using the TV remote control, you can play
media using the FUNCTIONS menu.
e.g.
e.g.,
2 Select an item, then press [OK].
Top Menu
Control Panel
Menu
SD card
Other Functions
OK
SUB
MENU S
RETURN
Control Panel is displayed.
Follow the indications on the
screen.
Screen Aspect
(> 12)
Top Menu [BD-V] [AVCHD] [DVD-V] Top menu is displayed.
Menu [DVD-V]
Menu is displayed.
Pop-up Menu [BD-V] [AVCHD]
Pop-up menu is displayed.
Rotate Right [JPEG]
Rotate the still picture.
Rotate Left [JPEG]
Zoom in [JPEG]
Enlarge or shrink the still
picture.
Zoom out [JPEG]
∫ When you want to leave the TV on and set only this unit to standby mode
Press [Í BD POWER] on this unit’s remote control and set to standby mode.
∫ When not using “HDAVI Control”
Set “EZ Sync” in the Setup menu to “Off”. (> 22)
RQT9139
(ENG)
17
DMP-BD30PP_Book1.book
18 ページ 2008年1月29日 火曜日 午後1時46分
Settings 11 Changing settings with the on-screen menu
Changing settings with the on-screen menu
On-screen menu operations
1 Press [DISPLAY].
e.g., BD-Video
2 Press [3, 4] to select
the menu and press [1].
3 Press [3, 4] to select
the item and press [1].
4 Press [3, 4] to select
the setting.
Disc
Play
Video
Audio
Signal Type
Subtitle
Off
Subtitle Style
Menus
-
Items
PIP
1ENG
Angle
NOTE
-
≥Depending on the condition of the
unit (playing, stopped, etc.) and
disc contents, there may be some
items that you cannot select or
change.
≥Some items can be changed by
pressing [OK].
Settings
TIPS
To exit the on-screen menu
Press [DISPLAY].
What you can change with the on-screen menu
Menus
Disc
Items
Settings and details
Signal Type
[BD-V]
≥Primary Video
Video:
The video recording method appears. (D below, Video recording method)
Soundtrack: Select the type of audio or language. (D below, Language, Audio attribute)
≥Secondary Video
Video:
Select on/off of images.
The video recording method appears. (D below, Video recording method)
Soundtrack: Select on/off of audio and the language. (D below, Language, Audio attribute)
Video
[AVCHD]
The video recording method appears. (D below, Video recording method)
Soundtrack
[AVCHD] [DVD-V]
Select the type of audio or language. (D below, Language, Audio attribute)
[DVD-VR]
The audio attributes appear. (D below, Audio attribute)
Subtitle
[BD-V] [AVCHD] [DVD-V]
Turn the subtitle on/off and select the language. (D below, Language)
[DVD-VR] (Only discs that contain subtitle on/off information)
Turn the subtitle on/off.
Subtitle Style
[BD-V]
Select the subtitle style.
Audio channel
[DVD-VR]
(> 12, Changing audio during play)
Angle
[BD-V] [DVD-V]
Select the number of the angle.
Some items may be changed only on the disc specific menu. (> 11, 13)
Language
ENG:
FRA:
DEU:
ITA:
ESP:
NLD:
SVE:
NOR:
English
French
German
Italian
Spanish
Dutch
Swedish
Norwegian
Audio attribute
DAN:
POR:
RUS:
JPN:
CHI:
KOR:
MAL:
VIE:
Danish
Portuguese
Russian
Japanese
Chinese
Korean
Malay
Vietnamese
THA:
POL:
CES:
SLK:
HUN:
FIN:
¢:
Thai
Polish
Czech
Slovak
Hungarian
Finnish
Others
LPCM/ÎDigital/ÎDigital+/
ÎTrueHD/DTS/DTS-HD
Signal type
ch (channel)
Number of channels
k (kHz)
Sampling frequency
b (bit)
Number of bits
Video recording method
MPEG-2
MPEG-4 AVC
VC-1
RQT9139
(ENG)
18
This is a standard for compressing and decompressing color motion pictures efficiently. This compression method is
used for DVDs, etc.
These are standards for compressing and decompressing color motion pictures more efficiently than MPEG-2 and used
for Blu-ray Discs, etc.
DMP-BD30PP_Book1.book
19 ページ 2008年1月29日 火曜日 午後1時46分
Settings 11 Changing settings with the on-screen menu
Menus
Play
Video
Items
Settings and details
Repeat Play
(Only when the elapsed time is being displayed on the unit’s display.)
Selects the item which you want to repeat. The items displayed differ depending on the type of
disc.
≥All tracks
All tracks
≥Chapter
Chapter
≥PL
Playlist
≥Title
Title
≥One track
Track
≥Off
Select “Off” to cancel.
Random
[CD] [MP3]
While playing, press [3, 4] to select “On”.
Random playback starts from the next track.
≥On
≥Off
Picture
[BD-V] [AVCHD] [DVD-VR] [DVD-V]
Select the picture quality mode during play.
≥Normal: Default setting
≥Soft:
Soft picture with fewer video artifacts
≥Fine:
Details are sharper
≥Cinema: Mellows movies, enhances detail in dark scenes.
≥User:
You can make further adjustments. (> below)
Audio
Progressive
If images are stretched from right to left, set to “Off”.
[Only when you have selected “480p” in “Component Video Resolution” (> 22)]
≥Depending on the type of television used, the video may be stretched horizontally when video
is output in progressive mode. When this occurs, select “Off” and the video will then be output
as “480i”.
≥This setting will be fixed to “On” if you connect with an HDMI cable and set “HDMI Video Mode”
to “On” (> 22).
≥When using a component video cable and progressive output is on, closed captions cannot be
displayed.
Transfer
[When “Progressive” (> above) is set to “On”.]
Select the method of conversion for progressive output to suit the type of material being played
(> 29, Film and video).
≥Auto (normal): Automatically detects the film and video content, and appropriately converts it.
≥Video:
Select when using “Auto”, and the content is distorted.
Sound Effects§
Re-master (> 12)
≥Re-master 1
≥Re-master 2
≥Re-master 3
≥Off
Settings
1 Press [1] to select “Picture Adjustment” and press [OK].
2 Select the item using [3, 4] and adjust it with [2, 1].
Contrast:
Increases the contrast between light and dark parts of the picture (j7 to
i7).
Brightness:
Brightens the picture (0 to i15).
Sharpness:
Adjusts the sharpness of the edges of the horizontal lines (j6 to i6).
Color:
Adjusts the shade of the picture’s color (j7 to i7).
Gamma:
Adjusts the brightness of dark portions of the screen (0 to i5).
3D NR:
Reduces the rough noise in the background to give a greater feeling of
depth (0 to i4).
When “BD-Video 24p Output” is set to “On”, this function may not
operate. (> 22)
Integrated NR: Smooths block noise and reduces the smudging that appears around
contrasting sections of the picture (0 to i3).
V. Surround
[BD-V] [AVCHD] [DVD-VR] [DVD-V] (2 channels or more only)
Enjoy a surround-like effect if you are using two front speakers only.
– Turn V. Surround off if it causes distortion.
– Do not use in combination with surround effects on other equipment.
– V. Surround does not work for bilingual recordings.
≥V. Surround 1
≥V. Surround 2
≥Off
Dialog Enhancer§
[BD-V] [AVCHD] [DVD-VR] [DVD-V] (3 channels or more only, including a center channel)
The volume of the center channel is raised to make dialog easier to hear.
≥On
≥Off
§
This function is effective for audio from the HDMI terminal or the DIGITAL AUDIO OUT terminal only when “Digital Audio Output” is set to
“PCM”. (However, in this case, audio is output as 2ch from the DIGITAL AUDIO OUT terminal.)
RQT9139
(ENG)
19
DMP-BD30PP_Book1.book
20 ページ 2008年1月29日 火曜日 午後1時46分
Settings 11 Changing the unit’s settings
Changing the unit’s settings
Change the unit’s settings if necessary. The settings remain intact even if you switch the unit to standby.
Setup menu operations
1
While stopped
Press [SETUP].
2 Press [3, 4] to select the tab and
press [OK].
3 Press [3, 4] to select the menu
and press [OK].
Setup
Setup
NOTE
Disc
≥There may be differences in
operation methods. If this happens,
follow the on-screen instructions
for the operation.
Video
To return to the previous screen
Press [RETURN].
Audio
Display
TIPS
TV / Device Connection
If there are any other items, repeat these steps.
4 Press [3, 4, 2, 1] to select the
option and press [OK].
To exit the screen
Press [SETUP].
OK
RETURN
Summary of settings
Underlined items are the factory presets.
“Setup” tab
Off Timer
Select how long the unit remains on when it is not being used.
Remote Control Code (> 26)
Easy Setting
You can execute basic settings (On-screen Language, TV Aspect).
Restore Default Settings
This returns all values in the Setup menu and the on-screen menu,
except for “Remote Control Code”, “On-screen Language”,
“DVD-Video Ratings” and “BD-Video Ratings” to the default settings.
≥2 Hours
≥6 Hours
≥Off
≥Set Code 1 ≥Set Code 2
≥Yes
≥No
≥Yes
≥Set Code 3
≥No
“Disc” tab
DVD-Video Ratings
Set a ratings level to
limit DVD-Video play.
BD-Video Ratings
Set an age limit of
BD-Video play.
Audio Language
Subtitle
Language
Menu Language
≥8 No Limit:
≥1 to 7:
Follow the on-screen instructions. Enter a
4-digit password with the numbered buttons
when the password screen is shown. It will be
the common password for both “DVD-Video
Ratings” and “BD-Video Ratings”.
≥Do not forget your password.
Choose the language for audio, subtitle and
disc menus.
[BD-V] [DVD-V]
≥Some discs start in a certain language
despite any changes you make here.
≥When the selected language is not available
on the disc, the default language is played.
There are discs where you can only switch
the language from the menu screen.
(> 11, 13)
≥Enter a code (> 28) with the numbered
buttons when you select “Other ¢¢¢¢”.
All DVD-Video can be played.
Prohibits play of DVD-Video with corresponding
ratings recorded on them.
≥0 Lock All:
Prohibits play of all DVD-Video.
≥Unlock Player
≥Change Password
≥Change Level
≥Temporary Unlock
All BD-Video can be played.
≥No Limit:
≥0 to 254 year(s): Prohibits play of BD-Video with corresponding
ratings recorded on them.
≥Unlock Player
≥Change Password
≥Change Level
≥Temporary Unlock
≥Spanish
≥English ≥French
≥Original: The original language of each disc will be selected.
≥Other ¢¢¢¢
≥Automatic:
If the language selected for “Audio Language” is not available,
subtitles of that language will automatically appear if available on
that disc.
≥English ≥French
≥Spanish ≥Other ¢¢¢¢
≥Spanish ≥Other ¢¢¢¢
≥English ≥French
“Video” tab
Still Mode (paused video) [BD-V] [AVCHD] [DVD-V]
Select the type of picture shown when you pause playback (> 29,
Frames and fields).
≥Auto
≥Field:
≥Frame:
Seamless Play [DVD-VR]
Select the play mode between playlist chapter segments and partially
deleted titles.
≥On:
≥Off:
Black Level Control
Select lighter or darker for adjusting the black level control to the
desired setting for picture enhancement.
≥Lighter:
≥Darker:
Select if jittering occurs when “Auto” is selected. (The
picture is coarser.)
Select if small text or fine patterns cannot be seen clearly
when “Auto” is selected. (The picture is clearer and finer.)
The chapters in playlists are played seamlessly. This does
not work while searching or when there are several audio
types included on the playlist. Additionally, the positioning
of chapter segments may change slightly.
The points where chapters in playlists change are played
accurately, but the picture may freeze for a moment.
When video is output from VIDEO OUT or S VIDEO OUT
terminal.
When video is output from COMPONENT VIDEO OUT
terminal.
“Audio” tab
Dynamic Range Compression
[BD-V] [AVCHD] [DVD-V] (Dolby Digital, Dolby Digital Plus and Dolby
TrueHD only)
Change the dynamic range (> 29) for late night viewing.
RQT9139
(ENG)
20
≥On
≥Off
(Continued on the next page)
DMP-BD30PP_Book1.book
21 ページ 2008年1月29日 火曜日 午後1時46分
Settings 11 Changing the unit’s settings
“Audio” tab (continued)
Digital Audio Output
≥Press [OK] to show the following settings.
Dolby Digital
[Note]
≥Bitstream:
≥Not making the proper
When “Bitstream” is selected, audio is output as bitstreams from either the
settings may result in
HDMI AV OUT or DIGITAL AUDIO OUT terminal. Select “Bitstream” when
noise.
the connected equipment can decode the respective audio format. (The
Dolby Digital Plus/TrueHD
≥If the unit is connected with
logo shown on the left is displayed on the equipment.)
the HDMI AV OUT terminal, ≥PCM:
the specifications of the
When “PCM” is selected, these audio formats are output as PCM 5.1ch
connected equipment take
from the HDMI AV OUT and PCM 2ch from DIGITAL AUDIO OUT terminal.
DTS
preference over this unit and Select “PCM” when the connected equipment cannot decode the
audio selected in these
respective audio format. (The logo shown on the left is not displayed on
items may not be output
the equipment.)
(e.g., when a television is
connected, the HDMI audio
DTS-HD
output of this unit is limited
to down-mixed 2ch.)
Regarding 7.1ch LPCM
The settings described below are recommended to output as the original format.
– Connect the unit with the HDMI AV OUT terminal.§3
– Set “BD-Video Secondary Audio” to “Off”. (Otherwise down-mixed 5.1ch PCM will be output from the HDMI AV OUT terminal.)
§3Down-mixed 2ch PCM is output from the DIGITAL AUDIO OUT terminal, regardless of the “BD-Video Secondary Audio” setting.
“Display” tab
Status Messages
Choose whether to show status messages automatically.
On-screen Language
Choose the language for these menus and on-screen messages.
Screen Saver Function
This is to prevent burn-in on the screen.
≥When this is set to “On”, the masked-off area on the screen
becomes gray.
[Only when connecting with an HDMI cable or a component video
cable and “HDMI Resolution” (> 22) is set to any other mode than
“480p”, or “Component Video Resolution” (> 22) is set to “720p”
or “1080i”]
FL Display
Changes the brightness of the unit’s display.
SD Card LED Control
Set the lighting method for the lamp on the SD card slot.
License
≥Automatic
≥English
Settings
BD-Video Secondary Audio [BD-V]
≥On: The primary audio and secondary audio are mixed and output. The
sampling frequency is converted to 48 kHz.
Turn on/off the clicking sound on the menu and audio with
≥Off: The clicking sound on the menu and secondary audio are not output.
secondary video in picture-in-picture mode. (> 13)
PCM Down Conversion
≥On: Signals are converted to 48 kHz. (Choose when the connected
Select how to output audio with a sampling frequency of 96 kHz.
equipment cannot process signals with sampling frequency of
≥Signals are converted to 48 kHz despite the settings across in
96 kHz.)
the following cases:
≥Off: Signals are output as 96 kHz. (Choose when the connected
– when the signals have a sampling frequency of over 96 kHz
equipment can process signals with sampling frequency of 96 kHz.)
– when the disc has copy protection
– when “BD-Video Secondary Audio” is set to “On”
[Note]
Regarding Dolby Digital Plus/TrueHD, DTS-HD
The settings described in the shaded area are recommended to output the high specification audio of Dolby Digital Plus, Dolby TrueHD,
DTS-HD High Resolution Audio and DTS-HD Master Audio as the original format.
Settings of “Digital Audio Output”
Connected terminal
Audio formats are output as:
HDMI AV OUT terminal
≥“Bitstream” is selected.
Dolby Digital§2
≥“BD-Video Secondary Audio” is set to “On”.
DIGITAL AUDIO OUT terminal
The original format
HDMI AV OUT terminal§1
≥“Bitstream” is selected.
Dolby Digital or DTS Digital Surround
≥“BD-Video Secondary Audio” is set to “Off”.
DIGITAL AUDIO OUT terminal
(depending on the original format)
HDMI AV OUT terminal
Down-mixed 5.1ch PCM
≥“PCM” is selected.
≥“BD-Video Secondary Audio” setting is either “On” or “Off”.
DIGITAL AUDIO OUT terminal
Down-mixed 2ch PCM
§1In the following cases, audio is output as Dolby Digital or DTS Digital Surround.
– The connected device does not support Dolby Digital Plus, Dolby TrueHD, DTS-HD High Resolution Audio and DTS-HD Master Audio.
– Since multiple devices are connected using HDMI cables, operations on the device are restricted.
§2When playing BD-Video without secondary audio or clicking sound, the audio is output as the same format as if “BD-Video Secondary Audio”
was set to “Off”.
≥Off
≥Français ≥Español
≥On:
If there is no operation for 10 minutes or more, the displayed screen
switches to the other states automatically.
– When the Direct Navigator or FUNCTIONS menu is displayed, the
display returns to the screen saver mode.
– When CD or MP3 is played, the display returns to the screen saver
mode. (Playback continues.)
– When still pictures are shown (except for slideshows), the display
returns to the Direct Navigator screen.
≥Off
≥Bright
≥Dim: The display is dimmed.
≥Auto: The display is dimmed during playback and bright except playback.
≥Off
≥On
≥SD inserted: When this unit is turned on and SD card is inserted, the
lamp is lighted.
Information about the software used by this unit is displayed.
“TV/Device Connection” tab
TV Aspect
Set to match the type of television connected.
When connected to a 4:3 aspect television:
≥4:3 Pan & Scan:Video recorded for a widescreen is played as Pan & Scan
(unless prohibited by the producer of the disc). When
playing BD-Video, video is output as “4:3 Letterbox”.
≥4:3 Letterbox: Video recorded for a widescreen is played in the letterbox
style.
When connected to a 16:9 widescreen television:
Video recorded for 4:3 aspect screen is displayed as a 4:3
≥16:9:
ratio image in the center of the screen.
≥16:9 Full:
Video recorded for 4:3 aspect screen is displayed as a
horizontally stretched 16:9 image.
(Continued on the next page)
RQT9139
(ENG)
21
DMP-BD30PP_Book1.book
22 ページ 2008年1月29日 火曜日 午後1時46分
Settings 11 Changing the unit’s settings
“TV/Device Connection” tab (continued)
HDMI Connection
≥Press [OK] to show the following settings.
HDMI Video Mode
Select “On” when video is output from HDMI AV OUT
terminal.
HDMI Resolution
The items supported by the connected devices are
indicated on the screen as “¢”. When any item without
“¢” is selected, the images may be distorted.
≥On:
Images are output from the HDMI terminal in the resolution set in “HDMI
Resolution”. Video from COMPONENT VIDEO OUT terminal is output as “480i”.
≥Off
Images are output in the resolution set in “Component Video Resolution”.
Automatically selects the output resolution best suited to the
≥Auto:
connected television (1080p, 1080i, 720p or 480p).
≥480p
≥720p
≥1080i
≥1080p
When the unit is connected to an amplifier/receiver that does not support the
resolution set on the unit, the video cannot be output properly. In this case, use the
HDMI cable to connect the unit to the TV and then connect the unit to the amplifier/
receiver using a cable other than HDMI.
BD-Video 24p Output
≥On: Images in 24p are output in 24p as they are.
(This is effective only when “HDMI Resolution” is set to “Auto” or “1080p”
When playing BD-Video recorded in 24 frames, this unit
and “TV Aspect” is set to “16:9” or “16:9 Full”.)
displays each frame at 1/24 second intervalssthe same
However,
interval originally shot with the film movie.
– when video is being output at 24 frames, images from any other terminal
≥This item can be set only when the unit is connected to
than the HDMI terminal may not be output properly.
a TV with an HDMI terminal that supports 1080/24p
– when images other than 24p are played, images are output at 60p.
input.
≥Off
HDMI RGB Output Range
≥Standard:
Effective when connected to a device that only supports RGB output. ≥Enhanced: When the black and white images are not distinct.
HDMI Audio Output
≥On:
This setting selects whether or not to output audio from
≥Off: When the TV is connected to this unit using an HDMI cable, and this unit is
HDMI.
also connected to other devices, such as an amplifier/receiver using an
optical digital audio cable or a coaxial cable.
EZ Sync
≥On
Set to use “HDAVI Control” function when connected with ≥Off: Select when you do not want to use “HDAVI Control”.
an HDMI cable to a device that supports “HDAVI Control”.
Component Video Resolution
≥480i ≥480p ≥720p ≥1080i
This sets the video output resolution when using the
Even if you select “720p” or “1080i”, images are output in 480p when you play
component video terminal.
DVD-Video.
Speaker
≥Multi Channel: When using 3 or more speakers. (> below)
≥2 Channel:
When using two speakers.
You can set the unit to output the best possible sound for
2ch down-mix audio are output from Front L and Front R.
your speakers.
Changing the speaker setting to suit your speakers
When connecting to an amplifier/receiver to enjoy multi-channel surround sound, use the following settings on this unit if they cannot be set on the
amplifier/receiver.
The settings are not effective when outputting bitstream signals.
5.1ch speaker
7.1ch speaker
Center
connection
connection
Approximate room dimensions
Front (R)
Front (L)
C
C
: Actual
ms
dB
L
R
C
0.0
0.0
speaker
C
C
L
R
L
R
position
dB
SW
dB
D E
0.0
D E
: Ideal
0.0
speaker
Subwoofer
RS RS
SW
LS LS
F
Complete
position
dB
Complete
F
F
SW
0.0
Test
Test
E
D
F
LB
LS
RB
RS
: Primary
dB ms dB
LB
RB
LS
RS
listening
LS
RS
0.0
0.0 0.0
distance
Circle of constant primary listening distance
ms
LB
RB
0.0
D Center speaker
F Surround/Surround back
speakers
Difference
Setting
(LS) Surround (RS)
(LB) Surround back (RB)§
Approx.
34
cm
(1
ft.
1
in.)
1.0
ms
Difference
Setting
Approx.
68
cm
(2
ft.
2
in.)
2.0
ms
Approx.
170
cm
(5
ft.
6
in.)
5.0
ms
§ Surround back channel is enabled only when the unit is connected to
Approx. 102 cm (3 ft. 4 in.) 3.0 ms Approx. 340 cm (11 ft. 1 in.) 10.0 ms
an amplifier/receiver supporting HDMI 7.1 channel audio.
Speaker presence and size (A)
Approx. 136 cm (4 ft. 5 in.) 4.0 ms Approx. 510 cm (16 ft. 8 in.) 15.0 ms
1 Press [3, 4, 2, 1] to select the speaker icon (A) and press
Approx. 170 cm (5 ft. 6 in.) 5.0 ms
[OK].
2 Press [3, 4] to select the setting and press [OK].
Icon examples:
Surround speaker (LS)
LS
LS
≥Large: Select when the
speaker supports
low-frequency (under Large
Small
No
100 Hz) reproduction.
≥Small: Select when the speaker does not support low-frequency
reproduction.
In order to make an ideal listening environment, settings of speaker
sizes may be automatically adjusted.
For example, if the subwoofer is set to “No”, the front speakers will
automatically be set to “Large”. (In this case, we recommend
connecting a speaker that can reproduce bass below 100 Hz.)
Delay time (B)
RQT9139
(ENG)
22
For optimum listening with 7.1/5.1-channel sound, all the speakers,
except for the subwoofer, should be the same distance from the
seating position.
If you have to place the center, surround and surround back
speakers closer to the seating position, adjust the delay time to
make up for the difference.
If either distance D or F is less than E, find the difference in the
relevant table and change to the recommended setting.
1 Press [3, 4, 2, 1] to select the delay time box (B) and press
[OK].
2 Press [3, 4] to select the setting and press [OK].
Channel balance (C)
This does not work when connected with the HDMI terminal and
“HDMI Audio Output” (D above) is set to “On”.
1 Select “Test” and press [OK].
A test signal is output.
Front (L)_—)Center_—)Front (R)_—)Surround (RS)
:
;
Surround (LS)(— Surround Back (LB)§ (— Surround Back (RB)§
§
Test signal is output only when the unit is connected using HDMI
AV OUT terminal.
2 While listening to the test signal, press [3, 4] to adjust the
volume of each speaker
Front speakers: 0.0 to s6.0 dB
Center and surround speakers: 0.0 to s12.0 dB
You cannot adjust the volume of surround back speakers.
3 Press [OK].
The test signal stops.
≥No signal is output for the subwoofer. To adjust its volume, play
something, then return to this screen to adjust to suit your taste.
4 Press [3, 4, 2, 1] to select “Complete” and press [OK].
DMP-BD30PP_Book1.book
23 ページ 2008年1月29日 火曜日 午後1時46分
Reference 11 Frequently asked questions
Frequently asked questions
Setup
Page
What do I need to play multi channel
surround sound?
≥Connect the appropriate amplifier/receiver to the HDMI terminal, the DIGITAL AUDIO
OUT terminal (OPTICAL, COAXIAL), or the 5.1ch AUDIO OUT terminal on this unit.
How do I set this unit to play 7.1ch
surround sound?
≥After connecting this unit to an amplifier/receiver compatible with Dolby Digital Plus,
Dolby TrueHD, DTS-HD and 7.1ch LPCM using an HDMI cable, set the items in the
Setup menu as follows.
– “Dolby Digital Plus/TrueHD”:
“Bitstream”
– “DTS-HD”:
“Bitstream”
– “BD-Video Secondary Audio”:
“Off”
– “Speaker”:
“Multi Channel”
21, 22
Can headphones and speakers be
directly connected to this unit?
≥You cannot directly connect them to this unit. Connect through the amplifier/receiver,
etc.
7, 8
My television has S VIDEO IN
terminal, COMPONENT VIDEO IN
terminals and HDMI IN terminal.
Which should I connect with?
≥The different levels of picture quality input are listed below in order from highest to
lowest.
HDMI IN )COMPONENT VIDEO IN )S VIDEO IN )VIDEO IN. However, it will take
longer for the picture output to start up when this unit is connected with the HDMI IN
terminal.
—
7, 8
Disc
Can I play BD-Video and DVD-Video
bought in another country?
≥You can play them if the video standard is NTSC, however, you cannot play:
– BD-Video discs that do not include region “A”.
– DVD-Video discs that do not include region “1” or “ALL”.
Refer to the disc’s jacket for more information.
Can BD-Video/DVD-Video that does
not have a region code/number be
played?
≥The region management information for BD-Video/DVD-Video indicates that the disc
conforms to industry standards. You cannot play discs that do not conform to industry
standards or do not have a region code or number.
—
Please tell me about disc
compatibility with this unit.
≥This unit plays BD-Video, DVD-Video, CD, BD-RE (BD-RE Recording Format/JPEG),
BD-R (BD-R Recording Format), DVD-RAM (DVD Video Recording format/AVCHD
format/JPEG), DVD-R/RW (DVD-Video format, DVD Video Recording format and
AVCHD format), DVD-R DL (DVD-Video format, DVD Video Recording format and
AVCHD format), +R, +RW and +R DL.
≥This unit also plays CD-R/RW discs which have been recorded in one of the following
standards: CD-DA, MP3 and still pictures (JPEG). Close the session after recording.
≥You cannot write to a disc with this unit.
4
Cover
4, 5
—
SD card
≥SD Memory Cards (from 8 MB to 2 GB), SDHC Memory Cards (from 4 GB to 16 GB),
miniSD Cards§, and microSD Cards§ can be used.
§
A miniSD Card and a microSD Card must be used in the attached adaptor.
Please confirm the latest information on the following website.
http://panasonic.co.jp/pavc/global/cs
(This site is in English only.)
≥[BD-V] To play the virtual package, it is recommended that you use a card that supports
SD Speed Class Rating Class 2 and has 256 MB or more free space.
—
—
13
4
Settings
What kinds of cards can be used?
≥The following operations are available.
– Playback JPEG data recorded with a digital camera etc.
– Playback AVCHD motion pictures recorded with Panasonic High Definition Video
Camera
– If a BD-Video disc supporting this function is used, it is possible to copy secondary
video recorded on the disc to the card and play it back together with the images on the
disc. (Virtual package)
—
Reference
What kinds of operations are
available on the SD card slot on this
unit?
RQT9139
(ENG)
23
DMP-BD30PP_Book1.book
24 ページ 2008年1月29日 火曜日 午後1時46分
Reference 11 Troubleshooting guide
Troubleshooting guide
Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the solutions indicated in the chart
do not solve the problem, refer to “Customer Services Directory” on page 30 if you reside in the U.S.A., or refer to “Product information” on
page 31 if you reside in Canada.
The following do not indicate a problem with this unit:
≥Regular disc rotating sounds.
≥Image disturbance during search.
To reset this unit
Page
To restore the unit if it freezes
due to one of the safety
devices being activated
≥Press and hold [POWER Í/I] on the main unit for 3 seconds. (The settings remain
unchanged.)
—
To return all settings other than
some settings to the factory
preset
≥Select “Yes” in “Restore Default Settings” in the Setup menu.
This returns all values in the Setup menu and the on-screen menu, except for “Remote
Control Code”, “On-screen Language”, “DVD-Video Ratings” and “BD-Video Ratings” to the
default settings.
20
To return to the factory preset
(No setting)
≥Reset the unit as follows:
1 Press [POWER Í/I] on the unit to turn off the unit.
2 Press and hold [9/5], [< OPEN/CLOSE] and [∫] on the unit at the same time for
more than 5 seconds until “HELLO” is displayed on the unit.
3 The power is turned on and then turned off automatically.
—
Power
No power.
≥Insert the AC power supply cord securely into a known active AC outlet.
6, 7
The unit switches to standby
mode.
≥This is a power saving feature. It can be changed if desired using “Off Timer” in the Setup
menu.
≥One of the unit’s safety devices is activated. Press [POWER Í/I] on the main unit to turn the
unit on.
20
≥Change the manufacturer code. Some televisions or amplifier/receiver cannot be operated
even if you change the code.
≥It may be necessary to set the manufacturer code again after changing the batteries.
≥The remote control and main unit are using different codes.
D
Change the code on the remote control.
R
Press and hold [OK] and the indicated number button at the
same time for more than 5 seconds.
≥The batteries are depleted. Replace them with new ones.
≥You are not pointing the remote control at the main unit’s remote control signal sensor during
operation.
≥Colored glass may obstruct the signal reception/transmission.
≥Don’t place the signal sensor in direct sunlight or in areas that may be subject to sunlight
exposure.
≥It may be necessary to set the code on the remote control again after changing the batteries.
≥Confirm the correct drive is selected.
≥Some operations may be prohibited by the disc.
≥The unit is hot (“U59” appears on the display). Wait for “U59” to disappear.
≥One of the unit’s safety devices may have been activated.
Reset the unit as follows:
1 Press [POWER Í/I] on the main unit to switch the unit to standby.
If the unit doesn’t switch to standby, press and hold [POWER Í/I] on the main unit for
about 3 seconds. The unit is forcibly switched to standby.
Alternatively, disconnect the AC power supply cord, wait one minute, then reconnect it.
2 Press [POWER Í/I] on the main unit to switch it on. If the unit still cannot be operated,
consult the dealer.
≥Condensation has formed: Wait 1 to 2 hours for it to evaporate.
≥Insert the disc correctly with the label facing up.
≥The disc is dirty.
≥You tried to play a blank disc or unplayable disc on this unit.
10
—
Operation
Cannot operate the television
or amplifier/receiver.
The remote control doesn’t
work properly.
The unit is on but cannot be
operated.
Play fails to start even when
[1] (PLAY) is pressed.
Play starts but then stops
immediately.
Cannot eject disc.
10
26
3
3
—
—
10, 26
11
—
27
—
—
11
27
4, 5
≥The unit may have a problem. While the unit is off, press and hold [;] and [9/5] on the
main unit at the same time for about 5 seconds. Remove the disc and consult the dealer.
≥Startup takes time in the following situations.
– Immediately after a power failure or the AC power supply cord is connected.
– When the unit is connected with an HDMI cable.
—
≥Only when the unit is connected to the HDMI terminal of a TV supporting 24p can you select
“On”. In some cases where the unit is connected to a TV via an amplifier/receiver through the
HDMI terminals, you may not be able to select “On”. In this case, connect the unit to a TV
through the HDMI terminal and connect it to the amplifier/receiver through any terminal other
than HDMI.
22
The display is dim.
≥Change “FL Display” in the Setup menu.
21
The elapsed time displayed is
actually less than the playtime.
≥The displayed play time is converted from the number of frames at 29.97 frames (equal to
0.999 seconds) to one second. There will be a slight difference between the time displayed
and the actual elapsed time (e.g., actual one-hour elapsed time may display as
approximately 59 minutes 56 seconds).
—
Startup is slow.
When the unit is turned on,
audio and video output takes a
long time.
Cannot set “On” in “BD-Video
24p Output”.
—
Displays
RQT9139
(ENG)
24
DMP-BD30PP_Book1.book
25 ページ 2008年1月29日 火曜日 午後1時46分
Reference 11 Troubleshooting guide
TV screen and video
Page
≥Make sure that the television is connected to the VIDEO OUT terminal, S VIDEO OUT
terminal, COMPONENT VIDEO OUT terminals or HDMI AV OUT terminal on this unit.
≥Make sure that the television’s input setting (e.g., VIDEO 1) is correct.
≥An incorrect resolution is selected in “Component Video Resolution”, when the television is
connected to COMPONENT VIDEO OUT terminals. While stopped, press and hold [∫] and
[1] (PLAY) on the main unit at the same time for more than 5 seconds to cancel this setting.
Set the item again.
≥If “BD-Video 24p Output” is turned “On” when the unit is connected to a TV through any
terminal other than HDMI, images may not display properly. In this case, turn “BD-Video 24p
Output” to “Off”.
6, 7
The screen changes
automatically.
≥When the “Screen Saver Function” in the Setup menu is set to “On”, the display may return to
the screen saver mode automatically if there is no operation for 10 minutes or more.
21
Video is not output in high
definition.
≥High definition video cannot be output through the VIDEO OUT or S VIDEO OUT terminals.
≥Confirm that the “HDMI Video Mode”, “HDMI Resolution”, and “Component Video
Resolution” in the Setup menu are set properly.
≥Depending on the BD-Video, output from the COMPONENT VIDEO OUT terminals may be
restricted to 480p.
—
22
Status messages do not
appear.
≥Select “Automatic” in “Status Messages” in the Setup menu.
21
The 4:3 aspect ratio picture
expands left and right.
≥Use the television to change the aspect. Refer to your television’s operating instructions.
≥When using a component video cable, set “Progressive” to “Off”. If the situation is not
restored after that, set “TV Aspect” to “4:3 Pan & Scan”.
The images from this unit do
not appear on the television.
Picture is distorted.
—
22
22
—
—
19, 21
Screen size is wrong.
There is a lot of after-image
when playing video.
≥Turn “3D NR” or “Integrated NR” off if it is on.
19
When playing DVD-Video using
progressive output, one part of
the picture momentarily
appears to be doubled up.
≥Set “Progressive” of “Video” menu on the on-screen menu to “Off”. This problem is caused by
the editing method or material used on DVD-Video, but should be corrected if you use
interlace output.
≥When the unit is connected using HDMI terminal, refer to “HDMI connections” (> below).
19
There is no apparent change in
picture quality when adjusted
with the Video menu in the
on-screen menu.
≥The effect is less perceivable with some types of video.
—
The masked-off area is masked
in gray.
≥If the “Screen Saver Function” in the Setup menu is set to “Off”, the masked-off area is
displayed in black.
21
—
Sound
No sound.
Low volume.
Distorted sound.
Cannot hear the desired audio
type.
Cannot switch audio.
≥Check the connections and the “Digital Audio Output” settings. Check the input mode on the
amplifier/receiver if you have connected one.
≥Press [AUDIO] to select the audio.
≥Turn off “V. Surround” in the following cases.
– When using discs that do not have surround sound effects such as Karaoke discs.
– When playing bilingual broadcast programs.
≥Match the speaker settings with the connected equipment. Change multi channel speaker
settings by selecting “Multi Channel” in “Speaker”.
≥The sound effects (Re-master, V. Surround, etc.) will not work when the bitstream signal is
output from the HDMI AV OUT terminal or the DIGITAL AUDIO OUT terminal.
≥When “BD-Video Secondary Audio” is set to “Off”, Dolby Digital Plus, Dolby TrueHD and
DTS-HD are output from the DIGITAL AUDIO OUT terminal as Dolby Digital or DTS Digital
Surround bitstream.
6–8, 21
≥There are discs for which audio cannot be changed because of how the disc was created.
≥When connecting an amplifier/receiver using a coaxial cable, optical digital audio cable or an
HDMI cable, you cannot switch the audio if “Digital Audio Output” is set to “Bitstream”. Set
“Digital Audio Output” to “PCM” or connect using audio cables.
—
7, 8, 21
≥Press [∫] and [1] (PLAY) simultaneously on the unit for more than 5 seconds to shift the
mode to one more compatible with HDMI equipment. However, Dolby Digital Plus, Dolby
TrueHD, and DTS-HD audio are not output in bitstream. To output the bitstream, select
“Restore Default Settings” to restore the factory presets and make proper settings.
≥To output video from a device connected with an HDMI cable, set “HDMI Video Mode” to “On”
in the Setup menu.
≥Picture may not be seen when more than 4 devices are connected with HDMI cables.
Reduce the number of connected devices.
≥When “BD-Video 24p Output” is set to “On”, HDMI authentication takes place where 24p
images switch to other images, and a black screen is displayed.
≥Change “TV Aspect” type to “16:9”.
20
≥When you use the HDMI AV OUT terminal for video output, follow the steps below for setting.
1 Connect this unit to the TV with any cable except the HDMI cable.
2 When you connect with the Component Video cable, set “HDMI Video Mode” to “Off” and
“Component Video Resolution” to “480i” in the Setup menu.
22
12
19
22
—
—
HDMI connections
Picture is distorted.
The 4:3 aspect ratio picture
expands left and right.
Screen size is wrong.
When playing DVD-Video using
progressive output, one part of
the picture momentarily
appears to be doubled up.
22
—
22
21
Reference
The images from this unit do
not appear on the television.
(Continued on the next page)
RQT9139
(ENG)
25
DMP-BD30PP_Book1.book
26 ページ 2008年1月29日 火曜日 午後1時46分
Reference 11 Troubleshooting guide
HDMI connections (continued)
No sound.
Low volume.
Distorted sound.
Cannot hear the desired audio
type.
Page
≥Audio may not be heard when more than 4 devices are connected with HDMI cables.
Reduce the number of connected devices.
≥The sound effects will not work when the bitstream signal is output from the HDMI AV OUT
terminal or the DIGITAL AUDIO OUT terminal.
≥To output audio from a device connected with an HDMI cable, set “HDMI Audio Output” to
“On” in the Setup menu.
≥If the sound is distorted when the unit is connected to an amplifier/receiver with an HDMI
cable, adjust the settings in “Speaker” in the Setup menu to match the connection.
≥Depending on the connected equipment, the sound may be distorted if this unit is connected
with an HDMI cable.
≥When “BD-Video Secondary Audio” is set to “On”, Dolby Digital Plus, Dolby TrueHD, and
DTS-HD are converted to 48 kHz Dolby Digital and output. LPCM 7.1 channel audio is
converted to 5.1 channel audio. In this case, set the “BD-Video Secondary Audio” to “Off”.
—
—
22
22
—
21
Card
The capacity of the SD card
decreased.
MPEG-2 motion pictures and
music on an SD card cannot be
played.
The contents of the card
cannot be read.
≥When a BD-Video that supports the virtual package is used, and an SD card is in the slot,
data may be written to the SD card. Erase the data by using “BD-Video Data Erase”, format
the card or use a new card.
≥Data that can be played from an SD card are AVCHD and JPEG data.
13
≥The card is not compatible or the contents on the card may be damaged.
≥Turn off and then turn on the unit again.
4
—
4
Other difficulties with playback
Audio and video momentarily
pause.
BD-Video or DVD-Video is not
played.
Picture-in-picture is not played
with BD-Video.
The virtual package
is not played with BD-Video.
Alternative soundtrack and
subtitles cannot be selected.
No subtitles.
The subtitles overlap closed
captions recorded on discs.
Angle cannot be changed.
The resume play function does
not work.
≥This occurs between playlist chapters or scenes ([AVCHD]).
≥When playing a title recorded on both layers, the unit automatically switches between layers
and plays the title in the same way as a normal program. However, video and audio may
momentarily cut out when the unit is switching layers.
≥Ensure the disc is for the correct BD-Video region code or DVD-Video region number, and is
not defective.
≥You have set a ratings level to limit BD-Video or DVD-Video play. Change this setting.
≥Some BD-Video can only be output with HDMI.
—
—
Cover
20
—
—
≥Confirm whether the disc supports picture-in-picture.
≥Confirm whether the disc supports the virtual package.
≥The inserted SD card does not have sufficient available capacity.
≥The SD card is write-protected.
≥Sub contents copied to an SD card are provided by the disc producer as a part of the
BD-Video content. Even if you record images and audio onto an SD card, it cannot be played
as a virtual package.
≥The languages are not recorded on the disc.
≥You may not be able to use the on-screen menu to change the soundtrack and subtitles on
some discs. Use the disc’s menus to make changes.
≥Subtitles are not recorded on the disc.
≥Turn the subtitles on. Set “Subtitle” on the on-screen menu to “On”.
≥When progressive output is on, closed captions cannot be displayed.
≥Turn off the subtitles or turn off the closed caption setting on the TV.
13
—
4
13
—
11, 13
≥Angles can only be changed during scenes where different angles are recorded.
≥Memorized positions are canceled when
– pressing [∫] several times.
– opening the disc tray.
≥The resume play function may not work depending on the disc.
—
18
—
18
—
—
—
When other Panasonic products respond to this remote control
Change the remote control code on the main unit and the remote control (the two must match) if you place other Panasonic products close
together.
When the following indicator
1 Press [SETUP].
appears on the unit’s display and
2 Press [3, 4] to select “Setup” and press [OK].
you are unable to operate the unit
3 Press [3, 4] to select “Remote Control Code”
and press [OK].
4 Press [3, 4] to select the code (1, 2, or 3) and
press [OK].
5 To change the code on the remote control
While pressing [OK], press and hold the
numbered button ([1], [2] or [3]) for more than
5 seconds.
6 Press [OK].
RQT9139
(ENG)
26
Remote Control Code
Set Code 1
NOTE
D
R
Set Code 2
Set Code 3
Press [n] and [OK] together
for more than 5 seconds on
the remote.
The unit’s remote control code
Press and hold [OK] and the
indicated number button at the same
time for more than 5 seconds.
DMP-BD30PP_Book1.book
27 ページ 2008年1月29日 火曜日 午後1時46分
Reference 11 Messages/Disc and card handling/Maintenance
Messages
The following messages or service numbers appear on the television or unit’s display when something unusual is detected during startup and use.
On the television
Page
Cannot play.
≥You inserted an incompatible disc (Discs recorded in PAL video, etc.).
Cannot display on this unit.
≥You tried to play a non-compatible image.
≥Confirm “SD” on the unit’s display is not blinking and re-insert the card.
4, 5
5
—
No disc
≥The disc may be upside down.
—
$ This operation is currently disabled.
≥The operation is prohibited by the unit or disc.
—
F99
≥The unit fails to operate properly. Press [POWER Í/I] on the main unit to switch the unit to
standby for 3 seconds. Now press [POWER Í/I] on the main unit again to turn the unit on.
—
HDMI ONLY
≥Some BD-Video discs can only be output with HDMI.
—
No PLAY
≥There is a viewing restriction on a BD-Video or DVD-Video.
20
No READ
≥The disc is dirty or badly scratched. The unit cannot play.
—
PLEASE WAIT
≥Displayed when the unit is started and turned off. This is not a malfunction.
≥The unit is carrying out its recovery process. You cannot operate the unit while “PLEASE
WAIT” is displayed.
—
—
SET 
(“  ” stands for a number.)
≥The remote control and main unit are using different codes. Change the code on the
remote control.
Press and hold [OK] and the indicated number button at the same
D
time for more than 5 seconds.
R
26
UNFORMAT
≥You inserted an unformatted DVD-RAM, DVD-RW, +RW, an unused +R, +R DL or
DVD-RW (DVD-Video format).
—
UNSUPPORT
≥You have inserted a disc the unit cannot play.
U59
≥The unit is hot.
The unit switches to standby for safety reasons. Wait for about 30 minutes until the
message disappears.
Select a position with good ventilation when installing the unit. Do not block the cooling fan
on the rear of the unit.
—
U72
U73
≥The HDMI connection acts unusually.
– The connected equipment is not HDMI compatible.
– Please use HDMI cables that have the HDMI logo (as shown on the cover).
– The HDMI cable is damaged.
—
H or F
≥There is something unusual. (The service number displayed after H and F depends on the
unit’s condition.)
≥Check the unit using the troubleshooting guide. If the service number does not disappear,
do the following.
1 Disconnect the plug from the AC outlet, wait a few seconds, then reconnect it.
2 Press [POWER Í/I] to turn the power on. (The unit may be fixed.)
If the service number does not disappear despite doing the above, request service from
the dealer. Inform the dealer of the service number when requesting service.
—
On the unit’s display
Clean discs
DO
DO NOT
Wipe with a damp cloth and then wipe dry.
Disc and card handling precautions
≥Handle discs by the edges to avoid inadvertent scratches or
fingerprints on the disc.
≥Do not attach labels or stickers to discs (This may cause disc
warping, rendering it unusable).
≥Do not write on the label side with a ball-point pen or other writing
instrument.
≥Do not use record cleaning sprays, benzine, thinner, static
electricity prevention liquids or any other solvent.
≥Do not use scratch-proof protectors or covers.
≥Clean any dust, water, or foreign matter from the terminals on the
rear side of the card.
≥Do not use the following discs:
– Discs with exposed adhesive from removed stickers or labels
(rented discs etc).
– Discs that are badly warped or cracked.
– Irregularly shaped discs, such as heart shapes.
24–26
Maintenance
Clean this unit with a soft, dry cloth
≥Never use alcohol, paint thinner or benzine to clean this unit.
≥Before using chemically treated cloth, read the instructions that
came with the cloth carefully.
Observe the following points to ensure continued listening and
viewing pleasure.
Dust and dirt may adhere to the unit’s lens over time, making it
impossible to play discs.
Use the lens cleaner (not included) about once every year,
depending on frequency of use and the operating environment.
Carefully read the lens cleaner’s instructions before use.
Lens cleaner: RP-CL720PP
≥This lens cleaner is sold as specific for DIGA, but can be used
without problem on this unit as well.
The model number and serial number of this product can be
found on either the back or the bottom of the unit.
Please note them in the space provided below and keep for
future reference.
MODEL NUMBER
DMP-BD30
Reference
Disc and card
handling
4, 5
SERIAL NUMBER
User memo:
DATE OF PURCHASE _______________________________
DEALER NAME ____________________________________
DEALER ADDRESS _________________________________
__________________________________________________
TELEPHONE NUMBER ______________________________
RQT9139
(ENG)
27
DMP-BD30PP_Book1.book
28 ページ 2008年1月29日 火曜日 午後1時46分
Reference 11 Specifications
Specifications
Signal system:
NTSC
Operating temperature range:
i5 to i35 oC (i41 to i95 xF)
Operating humidity range:
10 to 80 % RH (no condensation)
Playable disc:
BD-Video
BD-ROM: Version 2
BD-RE:
Version 3 (Single Layer, Dual Layer), JPEG§6
BD-R
Version 2 (Single Layer, Dual Layer)
DVD-RAM:
DVD Video Recording format,
AVCHD format§7, JPEG§4
DVD-R/DVD-RW/DVD-R DL:
DVD-Video format§1, DVD-Video Recording
format, AVCHD format§1, 7
+R/+RW/+R DL:
Video§1, AVCHD format§1, 7
DVD-VIDEO:
DVD-Video format
CD-Audio:
CD-DA
CD-R/RW:
CD-DA, JPEG§5, MP3
SD card:
SD Memory Card§2 formatted FAT12, FAT16, FAT32§3:
JPEG§4, AVCHD format§7
Video output:
Output level:
1.0 Vp-p (75 ≠)
Output connector:
Pin jack (1 system)
S-video output:
Y output level:
1.0 Vp-p (75 ≠)
C output level:
0.286 Vp-p (75 ≠) at Burst
Output connector:
S terminal (1 system)
Component video output:
(1080i/720p/480p/480i)
Y output level:
1.0 Vp-p (75 ≠)
0.7 Vp-p (75 ≠)
PB output level:
PR output level:
0.7 Vp-p (75 ≠)
Output connector:
Pin jack (Y: green, PB: blue, PR: red)
(1 system)
Audio output:
Output level:
2 Vrms (1 kHz, 0 dB)
Output connector:
Pin jack
Number of connectors:
2 channel: 1 system
5.1 channel discrete output: 1 system
Audio performance:
Frequency response:
≥DVD (linear audio):
4 Hz to 22 kHz (48 kHz sampling)
4 Hz to 44 kHz (96 kHz sampling)
≥CD-Audio:
4 Hz to 20 kHz
S/N ratio:
115 dB
Dynamic range:
100 dB
Total harmonic distortion:
0.003 %
RQT9139
(ENG)
28
Language code list
Abkhazian:
6566
Afar:
6565
Afrikaans:
6570
Albanian:
8381
Ameharic:
6577
Arabic:
6582
Armenian:
7289
Assamese:
6583
Aymara:
6589
Azerbaijani:
6590
Bashkir:
6665
Basque:
6985
Bengali; Bangla:
6678
Bhutani:
6890
Bihari:
6672
Breton:
6682
Bulgarian:
6671
Burmese:
7789
Byelorussian: 6669
Cambodian:
7577
Digital audio output:
Optical digital output:
Optical terminal
Coaxial digital output:
Pin jack
HDMI AV output
Output format:
480p (525p)/1080i (1125i)/720p (750p)/1080p (1125p)
Output Connector:
Type A (19 pin)
HDMITM (Deep color, High Bit rate Audio)
≥This unit supports “HDAVI Control 2” functions.
SD card slot:
Output connector:
1 system
Optical pick-up:
System with 2 lenses
Wave length:
782 nm (CDs)/662 nm (DVDs)/405 nm (BDs)
LASER Specification
Class I LASER Product:
Wave length:
782 nm (CDs)/662 nm (DVDs)/405 nm (BDs)
Laser power:
No hazardous radiation is emitted with the safety protection
Power supply:
AC 120 V, 60 Hz
Power consumption:
approx. 25 W
less than 1 W
Power consumption in standby mode:
Dimensions (WkDkH)
Excluding the projecting parts:
430 mmk313 mmk59 mm
(16 15/16zk12 5/16zk2 5/16z)
Including the projecting parts:
430 mmk320 mmk59 mm
(16 15/16zk12 5/8zk2 5/16z)
Mass (Weight):
approx. 3.3 kg (7.3 lbs)
[Note]
Specifications are subject to change without notice.
§1 Finalizing is necessary.
§2 includes SDHC card
includes miniSD cards (need a miniSD Adaptor)
includes microSD cards (need a microSD Adaptor)
§3 Does not support long file name
§4 The total combined maximum number of recognizable picture
contents and folders: 3000 picture contents and 300 folders.
§5 The total combined maximum number of recognizable audio and
picture contents and folders: 999 audio and picture contents and
99 folders.
§6 The total combined maximum number of recognizable picture
contents and folders: 9999 picture contents and 300 folders.
§7 AVCHD format V1.0
≥Useable capacity will be less. (SD Card)
Enter the code with the numbered buttons.
Catalan:
6765 Gujarati:
7185 Lingala:
7678
Chinese:
9072 Hausa:
7265 Lithuanian:
7684
Corsican:
6779 Hebrew:
7387 Macedonian: 7775
Croatian:
7282 Hindi:
7273 Malagasy:
7771
Czech:
6783 Hungarian:
7285 Malay:
7783
Danish:
6865 Icelandic:
7383 Malayalam:
7776
Dutch:
7876 Indonesian:
7378 Maltese:
7784
English:
6978 Interlingua:
7365 Maori:
7773
Esperanto:
6979 Irish:
7165 Marathi:
7782
Estonian:
6984 Italian:
7384 Moldavian:
7779
Faroese:
7079 Japanese:
7465 Mongolian:
7778
Fiji:
7074 Javanese:
7487 Nauru:
7865
Finnish:
7073 Kannada:
7578 Nepali:
7869
French:
7082 Kashmiri:
7583 Norwegian:
7879
Frisian:
7089 Kazakh:
7575 Oriya:
7982
Galician:
7176 Kirghiz:
7589 Pashto, Pushto:8083
Georgian:
7565 Korean:
7579 Persian:
7065
German:
6869 Kurdish:
7585 Polish:
8076
Greek:
6976 Laotian:
7679 Portuguese:
8084
Greenlandic: 7576 Latin:
7665 Punjabi:
8065
Guarani:
7178 Latvian, Lettish:7686 Quechua:
8185
Rhaeto-Romance:
8277
Romanian:
8279
Russian:
8285
Samoan:
8377
Sanskrit:
8365
Scots Gaelic: 7168
Serbian:
8382
Serbo-Croatian:8372
Shona:
8378
Sindhi:
8368
Singhalese:
8373
Slovak:
8375
Slovenian:
8376
Somali:
8379
Spanish:
6983
Sundanese:
8385
Swahili:
8387
Swedish:
8386
Tagalog:
8476
Tajik:
8471
Tamil:
Tatar:
Telugu:
Thai:
Tibetan:
Tigrinya:
Tonga:
Turkish:
Turkmen:
Twi:
Ukrainian:
Urdu:
Uzbek:
Vietnamese:
Volapük:
Welsh:
Wolof:
Xhosa:
Yiddish:
Yoruba:
Zulu:
8465
8484
8469
8472
6679
8473
8479
8482
8475
8487
8575
8582
8590
8673
8679
6789
8779
8872
7473
8979
9085
DMP-BD30PP_Book1.book
29 ページ 2008年1月29日 火曜日 午後1時46分
Reference 11 Glossary
Glossary
Dolby Digital
This is a method of coding digital signals developed by Dolby
Laboratories. Apart from stereo (2-channel) audio, these signals can
also be multi-channel audio.
Dolby Digital Plus
Multi-channel audio and higher audio quality is made possible using
Dolby Digital Plus. BD-Video supports up to 7.1 channel output.
Dolby TrueHD
Dolby TrueHD is a very high quality audio format that reproduces the
studio master audio. BD-Video supports up to 7.1 channel output.
Down-mixing
This is the process of remixing the multi-channel audio found on
some discs into fewer channels.
DTS (Digital Theater Systems)
This surround system is used in many movie theaters. There is good
separation between the channels, so realistic sound effects are
possible.
DTS-HD
DTS-HD is a high-quality, sophisticated audio format used in movie
theaters. Previous DTS Digital Surround-compatible equipment can
play DTS-HD as DTS Digital Surround audio. BD-Video supports up
to 7.1 channel output.
Dynamic range
Dynamic range is the difference between the lowest level of sound
that can be heard above the noise of the equipment and the highest
level of sound before distortion occurs.
Dynamic range compression means reducing the gap between the
loudest and softest sounds. This means you can listen at low
volumes but still hear dialog clearly.
Film and video
DVD-Video are recorded using either film or video. This unit can
determine which type has been used, then uses the most suitable
method of progressive output.
Film: Recorded at 24 frames per second. (Recorded at 30 frames
per second as well). Generally appropriate for motion picture
films.
Video: Recorded at 30 frames/60 fields per second. Generally
appropriate for TV drama programs or animation.
Final Standard Profile (FSP)
This is a BD-Video [BD-ROM version 2 (Profile 1 version 1.1)] that
supports the new functions such as Picture-in-picture, Secondary
Audio, and Virtual Package, etc.
Frames and fields
Frames refer to the single images that constitute the video you see
on your television. Each frame consists of two fields.
u
r
Frame
Field
Field
≥A frame still shows two fields, so there may be some blurring, but
picture quality is generally better.
≥A field still shows less picture information so it may be rougher, but
there is no blurring.
HDMI (High-Definition Multimedia Interface)
HDMI is a digital interface for consumer electronic products. Unlike
conventional connections, it transmits uncompressed digital video
and audio signals on a single cable.
JPEG (Joint Photographic Experts Group)
This is a system used for compressing/decoding color still pictures. If
you select JPEG as the storage system on digital cameras, etc., the
data will be compressed to 1/10–1/100 of its original size. The
benefit of JPEG is less deterioration in picture quality considering
the degree of compression.
Local storage
This storage area is used as a destination for sub contents for
playing virtual packages on BD-Video.
LPCM (Linear PCM)
These are uncompressed digital signals, similar to those found on
CDs.
MP3 (MPEG Audio Layer 3)
An audio compression method that compresses audio to
approximately one tenth of its size without any significant loss of
audio quality.
Pan&Scan/Letterbox
In general, DVD-Video are produced with the intention that they be
viewed on a widescreen television (16:9 aspect ratio), so images
often don’t fit regular (4:3 aspect ratio) televisions. Two styles of
picture, “Pan & Scan” and “Letterbox”, deal with this problem.
Pan&Scan: The sides are cut off so the picture fills
the screen.
Letterbox: Black bands appear at the top and
bottom of the picture so the picture itself
appears in an aspect ratio of 16:9.
Picture-in-picture
This is a new function of BD-Video that plays the primary video and
secondary video simultaneously. For instance, the function is
capable of playing the original movie as the primary video while
playing video commentary from the film director on a small screen
as a secondary video.
Progressive/Interlace
The video signal standard of NTSC has 480 interlaced (i) scan lines,
whereas progressive (p) scanning uses twice the number of scan
lines, and this is referred to as 480p. Using progressive output, you
can enjoy watching high resolution video.
Sampling frequency
Sampling is the process of converting the heights of sound wave
(analog signal) samples taken at set periods into digits (digital
encoding). Sampling frequency is the number of samples taken per
second, so larger numbers mean more faithful reproduction of the
original sound.
Virtual package
Some BD-Video discs copy data to other media (local storage) and
then play the secondary video, secondary audio, and subtitles (sub
contents) simultaneously.
These functions are called virtual packages.
Sub contents are automatically recorded to other media from the
disc prior to playing the virtual package. The playback methods vary
depending on discs.
1080i (1125i)
In one high definition image, 1080 (1125) alternating scan lines pass
to create an interlaced image. Because 1080i (1125i) more than
doubles current television broadcasts of 480i, the detail is much
clearer and creates a more realistic and rich image.
1080p (1125p)
In one high definition image, 1080 (1125) scan lines pass at the
same time to create a progressive image. Since progressive video
does not alternate scan lines like interlace, there is a minimal
amount of screen flicker.
24p
This is a progressive image recorded at a rate of 24 frames per
second.
720p (750p)
In one high definition image, 720 (750) scan lines pass at the same
time to create a progressive image. Since progressive video does
not alternate scan lines like interlace, there is a minimal amount of
screen flicker.
Reference
AVCHD
AVCHD is a new format (standard) for high definition video cameras
that can be used to record and play high-resolution HD images.
BD-J
Some BD-Video discs contain Java applications, and these
applications are called BD-J. You can enjoy various interactive
features in addition to playing normal video.
Bitstream
This is the digital form of multi-channel audio data (e.g., 5.1 channel)
before it is decoded into its various channels.
RQT9139
(ENG)
29
DMP-BD30PP_Book1.book
30 ページ 2008年1月29日 火曜日 午後1時46分
Reference 11 Limited Warranty (ONLY FOR U.S.A. )
Limited Warranty (ONLY FOR U.S.A. )
Panasonic Consumer Electronics Company,
Division of Panasonic Corporation of North America
Panasonic Puerto Rico, Inc.
Ave. 65 de Infantería, Km. 9.5
San Gabriel Industrial Park, Carolina, Puerto Rico 00985
One Panasonic Way Secaucus, New Jersey 07094
Panasonic Blu-ray Disc Player Limited Warranty
Limited Warranty Coverage
If your product does not work properly because of a defect in materials or
workmanship, Panasonic Consumer Electronics Company or Panasonic
Puerto Rico, Inc. (collectively referred to as “the warrantor”) will, for the
length of the period indicated on the chart below, which starts with the
date of original purchase (“Limited Warranty period”), at its option either
(a) repair your product with new or refurbished parts, or (b) replace it with
a new or a refurbished product. The decision to repair or replace will be
made by the warrantor.
Product or Part Name
Blu-ray Disc Player
Parts
Labor
One (1) Year
One (1) Year
Rechargeable Batteries
Ten (10) Days
(in exchange for defective item)
Not Applicable
During the “Labor” Limited Warranty period there will be no charge
for labor. During the “Parts” warranty period, there will be no charge
for parts. You must mail-in your product during the warranty period. If
non-rechargeable batteries are included, they are not warranted.
This Limited Warranty only applies to products purchased and
serviced in the United States or Puerto Rico. This Limited Warranty
is extended only to the original purchaser and only covers product
purchased as new. A purchase receipt or other proof of original
purchase date is required for Limited Warranty service.
For assistance in Puerto Rico call Panasonic Puerto Rico, Inc.
(787)-750-4300 or fax (787)-768-2910.
Limited Warranty Limits And Exclusions
This Limited Warranty ONLY COVERS failures due to defects in
materials or workmanship, and DOES NOT COVER normal wear and
tear or cosmetic damage. The Limited Warranty ALSO DOES NOT
COVER damages which occurred in shipment, or failures which are
caused by products not supplied by the warrantor, or failures which
result from accidents, misuse, abuse, neglect, mishandling,
misapplication, alteration, faulty installation, set-up adjustments,
misadjustment of consumer controls, improper maintenance, power line
surge, lightning damage, modification, or commercial use (such as
hotel, office, restaurant, or other business), rental use of the product, or
service by anyone other than a Factory Servicenter or other Authorized
Servicer, or damage that is attributable to acts of God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED
UNDER “LIMITED WARRANTY COVERAGE”. THE WARRANTOR IS
NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING
OUT OF ANY BREACH OF THIS WARRANTY. (As examples, this
excludes damages for lost time, cost of having someone remove or
re-install an installed unit if applicable, travel to and from the servicer,
loss of or damage to media or images, data or other recorded content.
The items listed are not exclusive, but are for illustration only.)
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE
WARRANTY OF MERCHANTABILITY, ARE LIMITED TO THE
PERIOD OF THE LIMITED WARRANTY.
Some states do not allow the exclusion or limitation of incidental or
consequential damages, or limitations on how long an implied Limited
Warranty lasts, so the exclusions may not apply to you.
When shipping the unit carefully pack and send it prepaid,
adequately insured and preferably in the original carton. Include a
letter detailing the complaint and provide a day time phone and/or
email address where you can be reached.
IF REPAIR IS NEEDED DURING THE LIMITED WARRANTY
PERIOD THE PURCHASER WILL BE REQUIRED TO FURNISH A
SALES RECEIPT/PROOF OF PURCHASE INDICATING DATE OF
PURCHASE, AMOUNT PAID AND PLACE OF PURCHASE.
CUSTOMER WILL BE CHARGED FOR THE REPAIR OF ANY
UNIT RECEIVED WITHOUT SUCH PROOF OF PURCHASE.
This Limited Warranty gives you specific legal rights and you may also
have other rights which vary from state to state. If a problem with this
product develops during or after the Limited Warranty period, you may
contact your dealer or Servicenter. If the problem is not handled to
your satisfaction, then write to the warrantor’s Consumer Affairs
Department at the addresses listed for the warrantor.
PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS
LIMITED WARRANTY, ARE YOUR RESPONSIBILITY.
Customer Services Directory
Obtain Product Information and Operating Assistance; purchase Parts, Accessories, or obtain Literature by visiting our Web Site at:
http://www.panasonic.com/consumersupport
or, contact us via the web at:
http://www.panasonic.com/contactinfo
You may also contact us directly at:
1-800-211-PANA (7262),
Monday-Friday 9 am-9 pm; Saturday-Sunday 10 am-7 pm, EST.
For hearing or speech impaired TTY users, TTY: 1-877-833-8855
Accessory Purchases
Purchase Parts, Accessories and Instruction Books online for all Panasonic Products by visiting our Web Site at:
http://www.pstc.panasonic.com
or, send your request by E-mail to:
[email protected]
You may also contact us directly at:
1-800-332-5368 (Phone) 1-800-237-9080 (Fax Only) (Monday – Friday 9 am to 9 pm, EST.)
Panasonic Service and Technology Company
20421 84th Avenue South, Kent, WA 98032
(We Accept Visa, MasterCard, Discover Card, American Express, and Personal Checks)
For hearing or speech impaired TTY users, TTY : 1-866-605-1277
Product Repairs
MAIL TO:
Centralized Factory Servicenter
Panasonic Service and Technology Company
410B Airport Road
Elgin, IL 60123-9333
Attention: BD/DVD Repair
Please carefully pack and ship, prepaid and insured, to the Elgin Centralized Factory Servicenter. Customers in Puerto Rico, please ship or carry in
to location below (“Service in Puerto Rico”).
Service in Puerto Rico
RQT9139
(ENG)
30
Panasonic Puerto Rico, Inc.
Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985
Phone (787)750-4300, Fax (787)768-2910
As of January 2007
DMP-BD30PP_Book1.book
31 ページ 2008年1月29日 火曜日 午後1時46分
Reference 11 Limited Warranty (ONLY FOR CANADA)/Product Service
Limited Warranty (ONLY FOR CANADA)
Panasonic Canada Inc.
PANASONIC PRODUCT—LIMITED WARRANTY
Panasonic Canada Inc. warrants this product to be free from defects in material and workmanship and agrees to remedy any such defect for a
period as stated below from the date of original purchase.
Technics Audio Product
Panasonic Portable/Clock Radio (without Tape, CD, MD)
Panasonic Audio/SD Audio Product
Panasonic BD/DVD Product
Panasonic Combination DVD Player/VCR
Panasonic Combination DVD Recorder/VCR
Accessories including rechargeable batteries
One (1) year, parts and labour
One (1) year, parts and labour
One (1) year, parts and labour
One (1) year, parts and labour
One (1) year, parts and labour
One (1) year, parts and labour
Ninety (90) days
LIMITATIONS AND EXCLUSIONS
This warranty does not apply to products purchased outside Canada or to any product which has been improperly installed, subjected to usage
for which the product was not designed, misused or abused, damaged during shipping, or which has been altered or repaired in any way that
affects the reliability or detracts from the performance, nor does it cover any product which is used commercially. Dry cell batteries are also
excluded from coverage under this warranty.
This warranty is extended to the original end user purchaser only. A purchase receipt or other proof of date of original purchase is required before
warranty service is performed.
THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
IN NO EVENT WILL PANASONIC CANADA INC. BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES.
In certain instances, some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, or the exclusion of implied
warranties, so the above limitations and exclusions may not be applicable.
WARRANTY SERVICE
FOR PRODUCT OPERATION ASSISTANCE, please contact:
Our Customer Care Centre:
Telephone #:
1-800 #:
Fax #:
Email link:
(905) 624-5505
1-800-561-5505
(905) 238-2360
“Customer support” on www.panasonic.ca
FOR PRODUCT REPAIRS, please locate your nearest Authorized Servicentre at www.panasonic.ca :
Link : “ServicentresTM locator” under “Customer support”
IF YOU SHIP THE PRODUCT TO A SERVICENTRE
Carefully pack and send prepaid, adequately insured and preferably in the original carton.
Include details of the defect claimed, and proof of date of original purchase.
1. Damage requiring service—The unit should be serviced by
qualified service personnel if:
(a) The AC power supply cord or AC adaptor has been
damaged; or
(b) Objects or liquids have gotten into the unit; or
(c) The unit has been exposed to rain; or
(d) The unit does not operate normally or exhibits a marked
change in performance; or
(e) The unit has been dropped or the cabinet damaged.
2. Servicing—Do not attempt to service the unit beyond that
described in these operating instructions. Refer all other
servicing to authorized servicing personnel.
3. Replacement parts—When parts need replacing ensure the
servicer uses parts specified by the manufacturer or parts that
have the same characteristics as the original parts.
Unauthorized substitutes may result in fire, electric shock, or
other hazards.
4. Safety check—After repairs or service, ask the servicer to
perform safety checks to confirm that the unit is in proper
working condition.
Product information
For product information or assistance with product operation:
Reference
Product Service
In the U.S.A., refer to “Customer Services Directory” on page 30.
In Canada, contact the Panasonic Canada Inc. Customer Care
Centre at 1-800-561-5505, or visit the website (www.panasonic.ca),
or an authorized Servicentre closest to you.
RQT9139
(ENG)
31
DMP-BD30PP_Book1.book
32 ページ 2008年1月29日 火曜日 午後1時46分
Reference 11 Referencia rápida en español
Conexiones básicas
A Conexión a un televisor con un cable
para audio/vídeo
B Conexión a un televisor compatible
con HDMI
HDMI IN
HDMI AV OUT
Cable HDMI
Cable de audio/
vídeo (incluido)
O
COAXIAL
COMPONENT VIDEO OUT
Y
PB
AUDIO IN
R
L VIDEO IN
AUDIO OU
L
Televisor
compatible
con HDMI
AV OUT
FRONT L /L SURROUN
AM)
DIGITAL AUDIO COAXIAL COMPONENT VIDEO OUT
Y
PB
OUT
(PCM/BITSTREAM)
AUDIO OUT
L
FRONT L /L SURROUND CENTER
L
R
FRONT R /R
Please
connect
directly
to TV.
AC IN
Televisor
PR
S VIDEO OUT VIDEO OUT
R
FRONT R /R
PR
S VIDEO OUT VIDEO OUT
R
2ch
SUBWOOFER
5.1ch
Parte posterior de la unidad
2ch
DIGITAL AUDIO COAXIAL COMPONENT VIDEO OUT
Y
PB
OUT
(PCM/BITSTREAM)
OPTICAL
AV OUT
PR
S VIDEO OUT VIDEO OUT
AUDIO/VIDEO IN
AUDIO OUT
L
FRONT L /L SURROUND CENTER
L
R
FRONT R /R
Please
connect
directly
to TV.
AC IN
OPTICAL
AV OUT
R
2ch
SUBWOOFER
5.1ch
Parte posterior de la unidad
≥Esta conexión no permite la salida de vídeo de alta definición.
Utilice la conexión B o C para obtener vídeo de alta definición.
C Conexión a un televisor compatible con HDMI y a un amplificador/receptor compatible con HDMI
Altavoces multicanal
HDMI AV OUT
HDMI IN
Cable HDMI
HDMI AV OUT
HDMI IN
Cable HDMI
Televisor
compatible
con HDMI
AV OUT
L
SURROUND
CENTER
Please
connect
directly
to TV.
AC IN
OPTICAL
PR
AV OUT
Parte posterior de la unidad
Amplificador/Receptor compatible con HDMI
Por último, conecte el cable de alimentación de CA
Ahorro de energía
Esta unidad consume una pequeña cantidad de energía aunque esté
ajustada en el modo de espera (aprox. 1 W). Para ahorrar energía cuando
no vaya a utilizar la unidad durante mucho tiempo, desenchúfela de la
toma de corriente.
A una toma de corriente doméstica
(CA 120 V, 60 Hz)
AC IN
DIGITAL AUDIO COAXIAL COMPONENT VIDEO OUT
Y
PB
OUT
(PCM/BITSTREAM)
AUDIO OUT
L
FRONT L /L SURROUND CENTER
L
R
FRONT R /R
Please
connect
directly
to TV.
AC IN
OPTICAL
AV OUT
PR
S VIDEO OUT VIDEO OUT
R
2ch
SUBWOOFER
5.1ch
Cable de alimentación de CA (incluido)
Conéctelo cuando haya realizado el resto de conexiones.
Reproducción básica
Preparación
VIDEO1
Encienda el televisor y seleccione la entrada de vídeo adecuada en el televisor.
1 Pulse [Í BD POWER] para encender la unidad.
Después de conectar su nuevo reprodutor y pulsar el botón de encendido, aparecerá la pantalla de la
configuración básica.
2 Pulse [< OPEN/CLOSE] para abirir la bandeja del disco, cargue el disco.
≥Pulse de nuevo el botón para cerrar la bandeja.
Inicia la reproducción.
SLOW/SEARCH
PLAY
STOP
Inicia la reproducción
Parada
La posición de detención se memoriza.
Función de reanudación de la reproducción
Pulse [1] (PLAY) para reiniciar la reproducción desde esta posición.
≥La posición se borra si se abre la bandeja o se pulsa [∫] varias
veces para visualizar “STOP” en el visor de la unidad.
PAUSE
Pausa
≥Pulse [;] otra vez o [1] (PLAY) para reiniciar la reproducción.
RQT9139
(ENG)
32
Búsqueda/
Cámara lenta
La velocidad aumenta hasta 5 pasos.
≥Pulse [1] (PLAY) para recuperar la velocidad de reproducción
normal.
≥Para algunos discos, la velocidad podría no cambiar.
Búsqueda
Durante la reproducción, pulse [6] o [5].
≥[BD-V] [AVCHD] [DVD-VR] [DVD-V]:
El audio se oye durante la búsqueda en avance de primer nivel.
≥[CD] [MP3]: La velocidad está fija en un paso.
Cámara lenta
Durante la pausa, pulse [6] o [5].
≥[BD-V] [AVCHD]: Sólo dirección en avance [5].
≥[DVD-VR]:Si continua durante aprox. 5 minutos, la reproducción en
cámara lenta se para automáticamente.
SKIP
Salto
Salta hasta el título, capítulo o pista que desee reproducir.
≥Cada pulsación aumenta el número de saltos.
DMP_BD30_PP_p16-32.fm
33 ページ 2008年3月5日 水曜日 午後1時54分
Reference 11 Index
Index
A Angle. . . . . . . . . . . . . . . . . . . . . . . . . . .18
Audio
Attribute . . . . . . . . . . . . . . . . . . . . . . .18
Changing audio . . . . . . . . . . . . . . . . .12
Channel . . . . . . . . . . . . . . . . . . . . . . .18
Language . . . . . . . . . . . . . . . . . . .18, 20
AVCHD . . . . . . . . . . . . . . . . . . . . . . . . .29
B BD-J . . . . . . . . . . . . . . . . . . . . . . . . . . .29
BD-Video Ratings . . . . . . . . . . . . . . . .20
C Chapter . . . . . . . . . . . . . . . . . . . . . . . . .14
Cleaning
Disc . . . . . . . . . . . . . . . . . . . . . . . . . .27
Lens . . . . . . . . . . . . . . . . . . . . . . . . . .27
Main unit . . . . . . . . . . . . . . . . . . . . . .27
Connection
Amplifier/Receiver . . . . . . . . . . . . . .7, 8
HDMI . . . . . . . . . . . . . . . . . . . . . . . .6, 7
D Dialog Enhancer . . . . . . . . . . . . . . . . .19
Direct Navigator . . . . . . . . . . . . . . . . . .11
Dolby Digital. . . . . . . . . . . . . . . . . .18, 21
Dolby Digital Plus . . . . . . . . . . . . .18, 21
Dolby TrueHD. . . . . . . . . . . . . . . . .18, 21
DTS . . . . . . . . . . . . . . . . . . . . . . . . .18, 21
DTS-HD . . . . . . . . . . . . . . . . . . . . . .18, 21
E EZ SyncTM “HDAVI ControlTM” . . . . . . .17
F Finalize . . . . . . . . . . . . . . . . . . . . . . . . . .4
Final Standard Profile . . . . . . . . . .13, 29
Format. . . . . . . . . . . . . . . . . . . . . . . . . .13
H HDMI . . . . . . . . . . . . . . . . . . . . . . .6, 7, 29
L Language
Audio . . . . . . . . . . . . . . . . . . . . . . 18, 20
Code list. . . . . . . . . . . . . . . . . . . . . . . 28
On-screen . . . . . . . . . . . . . . . . . . . . . 21
Soundtrack. . . . . . . . . . . . . . . . . . . . . 18
Subtitle. . . . . . . . . . . . . . . . . . . . . 18, 20
Local storage . . . . . . . . . . . . . . . . . . . . 29
LPCM . . . . . . . . . . . . . . . . . . . . . . . . . . 29
M Maintenance. . . . . . . . . . . . . . . . . . . . . 27
Menu
On-screen . . . . . . . . . . . . . . . . . . . . . 18
Pop-up . . . . . . . . . . . . . . . . . . . . . . . . 13
Setup . . . . . . . . . . . . . . . . . . . . . . . . . 20
Sub . . . . . . . . . . . . . . . . . . . . . . . . . . 14
MP3 . . . . . . . . . . . . . . . . . . . . . . . 5, 16, 29
N Noise reduction (NR)
Integrated NR . . . . . . . . . . . . . . . . . . 19
3D NR . . . . . . . . . . . . . . . . . . . . . . . . 19
O Off Timer. . . . . . . . . . . . . . . . . . . . . . . . 20
On-screen
Language. . . . . . . . . . . . . . . . . . . . . . 21
Menu . . . . . . . . . . . . . . . . . . . . . . . . . 18
Status messages . . . . . . . . . . . . . . . . 12
P PCM Down Conversion . . . . . . . . . . . . 21
Picture-in-picture. . . . . . . . . . . . . . . . 13
Picture quality adjustment . . . . . . . . . 19
Playlist . . . . . . . . . . . . . . . . . . . . . . . . . 16
Pop-up Menu . . . . . . . . . . . . . . . . . . . . 13
Progressive . . . . . . . . . . . . . . . . . . 19, 29
Properties
Chapter . . . . . . . . . . . . . . . . . . . . . . . 14
Still picture . . . . . . . . . . . . . . . . . . . . . 15
R Ratings level . . . . . . . . . . . . . . . . . . . . 20
Re-master. . . . . . . . . . . . . . . . . . . . 12, 19
Remote control code. . . . . . . . . . . . . . 26
Repeat play . . . . . . . . . . . . . . . . . . . . . 19
Restore Default Settings. . . . . . . . . . . 20
Resume play function . . . . . . . . . . . . . 12
S SD card . . . . . . . . . . . . . . . . . . . . . . . 4, 13
Setup menu . . . . . . . . . . . . . . . . . . . . . 20
Slideshow. . . . . . . . . . . . . . . . . . . . . . . 15
Soundtrack. . . . . . . . . . . . . . . . . . . . . . 18
Status Messages . . . . . . . . . . . . . . . . . 12
Still pictures. . . . . . . . . . . . . . . . . . . . . 14
Subtitle . . . . . . . . . . . . . . . . . . . . . . . . . 18
T Transfer . . . . . . . . . . . . . . . . . . . . . . . . 19
V V. Surround . . . . . . . . . . . . . . . . . . . . . 19
Virtual package . . . . . . . . . . . . . . . . . . 13
24p . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22, 29
J JPEG . . . . . . . . . . . . . . . . . . . . . .5, 14, 29
Java and all Java-based trademarks and logos are trademarks or registered trademarks of Sun Microsystems, Inc. in the United States and
other countries.
Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.
“DTS” is a registered trademark of DTS, Inc. and “DTS-HD Advanced Digital Out” is a trademark of DTS, Inc.
U.S. Patent Nos. 6,836,549; 6,381,747; 7,050,698; 6,516,132; and 5,583,936.
This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this
copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless
otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
This product is licensed under the AVC patent portfolio license and VC-1 patent portfolio license for the personal and non-commercial use of a
consumer to (i) encode video in compliance with the AVC Standard and VC-1 Standard (“AVC/VC-1 Video”) and/or (ii) decode AVC/VC-1 Video
that was encoded by a consumer engaged in a personal and non-commercial activity and/or was obtained from a video provider licensed to
provide AVC/VC-1 Video. No license is granted or shall be implied for any other use. Additional information may be obtained from MPEG LA,
LLC. See http://www.mpegla.com.
HDAVI Control™ is a trademark of Matsushita Electric Industrial Co., Ltd.
EZ Sync™ is a trademark of Matsushita Electric Industrial Co., Ltd.
“AVCHD” and the “AVCHD” logo are trademarks of Matsushita Electric Industrial Co., Ltd. and Sony Corporation.
SDHC Logo is a trademark.
Portions of this product are protected under copyright law and are provided under license by ARIS/SOLANA/4C.
-If you see this symbol-
[For\U.S.A.]
Panasonic Consumer Electronics
Company, Division of Panasonic
Corporation of North America
One Panasonic Way Secaucus,
New Jersey 07094
http://www.panasonic.com
Reference
Information on Disposal in other Countries outside the
European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact
your local authorities or dealer and ask for the correct
method of disposal.
[For\Canada]
Panasonic Puerto Rico, Inc.
Panasonic Canada Inc.
Ave. 65 de Infantería, Km. 9.5
San Gabriel Industrial Park, Carolina,
Puerto Rico 00985
5770 Ambler Drive
Mississauga, Ontario
L4W 2T3
www.panasonic.ca
C 2008 Matsushita Electric Industrial Co., Ltd.
Printed in China
pr
RQT9139-1Y
F0208UY1038
RQT9139
(ENG)
33

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement