GD00Z-4
GARAGE DOOR OPENER
REMOTE COMMAND
TRANSCEIVER with TILT SENSOR
Installation Instructions
USA & Canada (800) 421-1587 & (800) 392-0123
(760) 438-7000 - Toll Free FAX (800) 468-1340 www.linearcorp.com
➌
PRODUCT COMPONENTS
GD00Z-4
STATUS
INDICATOR
POWER
INPUT
JACK
CONNECTION
WIRES
WARNING
LIGHT
LINK
BUTTON
MOUNTING SCREWS
AND ANCHORS
FOR GD00Z-4
OPTIONAL
ADJUSTABLE
GD00Z-4 MOUNTING
BRACKET
TILT
SENSOR
SCREW AND
MOUNTING HARDWARE
FOR ADJUSTABLE
BRACKET
SCREWS AND
MOUNTING TAPE
FOR TILT SENSOR
WIRE
TIES
POWER
SUPPLY
POWER
SUPPLY
RETAINING
BRACKET
SCREW FOR
POWER SUPPLY
BRACKET
➊
PRODUCT DESCRIPTION
GD00Z-4 Overview
• A garage door opener remote command transceiver with built-in
Z-Wave technology.
• Allows remote operation of a garage door opener using Z-Wave controllers.
• Acts as a Z-Wave repeater to improve communications within the Z-Wave mesh network.
GD00Z-4 Summary of Operation
• GD00Z-4 connects to the garage door opener’s pushbutton wall console terminals.
garage door and reports the door’s position to the GD00Z-4.
• GD00Z-4 responds to Z-Wave commands from Z-Wave controllers to open or close the garage door.
Z-Wave Information
• Z-Wave® is a registered trademark of Sigma Designs Inc. and/or its subsidiaries.
• Z-Wave is an Interoperable two-way RF mesh networking technology designed for use with a Z-Wave gateway/ controller and other Z-Wave enabled devices.
• Replication is the process of copying or transferring your Z-Wave network from one controller to another.
• This is a Security enabled Z-Wave product and must be used with a
Security enabled Z-Wave controller in order to fully utilize this product. As such, this device will not respond to
Basic CC commands.
• ASSOCIATION: The GD00Z-4 supports
1 Group with 1 Node. Group 1 must be assigned the Node ID of the controller to which unsolicited notifi cations from the GD00Z-4 will be sent. The Z-Wave controller should set this association automatically after inclusion.
a beeper sounds for 5 seconds before the door begins to move.
• If the door does not completely open or close, a second open or close command can be sent after
30 seconds.
• If the door does not completely open or close after the second attempt, the GD00Z-4 operation is suspended until a local garage door pushbutton is activated.
➍
TILT SENSOR INSTALLATION AND BATTERY
To activate the tilt sensor,
1
remove the battery protection pull strip
2
Attach the mounting plate to the top panel of the door
3
Snap the sensor onto the mounting plate
ARROWS ON PLATE
& SENSOR POINT UP
➋
SAFETY NOTES
WARNING
This operator system is equipped with an unattended operation feature. This door could move unexpectedly.
NO ONE SHOULD CROSS THE PATH OF A MOVING DOOR!
WARNING
This system can be installed on sectional type (roll up) doors only per (UL-325). DO NOT INSTALL ON ONE-PIECE DOORS!
WARNING
The Remote Command Transceiver must be mounted in the garage, in sight of the garage door, where the visual and audible movement warning indicators can be clearly seen and heard.
WARNING
Do not install the Remote Command Transceiver on garage door operators manufactured prior to 1993
(models without an operational safety beam entrapment detection system).
➎
PAIRING (INCLUDING) WITH THE SYSTEM
Note: Plug in the GD00Z-4 near your Z-Wave Controller for these steps
WALL
OUTLET
POWER
SUPPLY
POWER
INPUT
JACK
GD00Z-4
LINK
BUTTON
"UP"
ARROWS
POST ON
BOTTOM
The system will notify you when the battery is low, replace the battery with a type CR2032 coin cell
1
To open the case, twist a small screwdriver in case slot
Use double sided tape or the two mounting screws supplied
(drill 1/16" pilot holes if required)
LOW BATTERY REPLACEMENT
2
Insert the battery into the transmitter
PLUS SIDE UP !!!
CR2032
SLOT
TO INCLUDE THE GD00Z-4
INTO YOUR CONTROLLER
1 Place your Z-Wave Controller into
Discovery or Include mode.
2 Press and release the link button on the GD00Z-4.
3 Confirm that the GD00Z-4 was recognized by your Z-Wave Controller.
Refer to your Z-Wave Controllers instructions for additional information on including devices.
TO EXCLUDE THE GD00Z-4
FROM YOUR CONTROLLER
1 Place your Z-Wave Controller into
Exclude mode.
2 Press and release the link button on the GD00Z-4.
3 Confirm that the GD00Z-4 was excluded by your Z-Wave Controller.
Refer to your Z-Wave Controllers instructions for additional information on excluding devices.
➏
GD00Z-4 MOUNTING
Tilt sensor mounted on the top panel of the door
The GD00Z-4 typically mounts on the ceiling near the opener and the power outlet
➐
GD00Z-4 CONNECTIONS
Plug the power cord 2 into the power input jack on the GD00Z-4
➑
SYSTEM OPERATION
1 Restore power to your garage door opener
! WARNING !
REMOVE POWER FROM THE
GARAGE DOOR OPENER
BEFORE CONTINUING
THE GD00Z-4 WARNING
LAMP MUST BE VISIBLE IN
ALL DOOR POSITIONS
THE GD00Z-4 CAN ALSO BE ATTACHED TO THE OPENER'S
HARDWARE USING THE ADJUSTABLE MOUNTING BRACKET
Secure bracket with screw
1A The optional adjustable mounting bracket fits
3 ways on the GD00Z-4
INDENT
INDENT
The bracket snaps onto indents on either side or on the end of the GD00Z-4
1
Connect the GD00Z-4 connection wires to the pushbutton wall console terminals on the garage door opener.
The terminals may be named "PWC", "WC",
"PB", "PUSHBUTTON", or "RED and WHITE".
Terminal names and locations vary by model.
3
Remove the screw from 120 VAC outlet faceplate. Secure the retaining bracket to the faceplate with the provided screw. Snap the power supply into the bracket while plugging into the outlet.
DO NOT DISCONNECT
ANY WIRES CURRENTLY
CONNECTED TO THE
GARAGE DOOR OPENER !!!
1
Use the four screws and anchors to mount the GD00Z-4 above the opener
3/16" HOLES
FOR ANCHORS
INDENT
Either wire can connect to either terminal
USE WIRE TIES TO SECURE
EXCESS WIRING CLEAR
OF ALL MOVING PARTS
OF THE GARAGE
DOOR AND OPENER
2A
Use the bolts and nuts supplied to attach the bracket to a secure structure
GARAGE
DOOR
OPENER
BE SURE THE GD00Z-4
IS CLEAR OF ALL MOVING
PARTS OF THE GARAGE DOOR
AND THE WARNING LAMP IS
NOT OBSTRUCTED
➒
OPERATION NOTES
1. The warning light will fl ash and the warning beeper will sound for fi ve seconds before the door opener is activated. STAY CLEAR OF THE DOOR, AND DOOR
OPENER. THEY ARE ABOUT TO MOVE!
2. If the door does not completely open or close after remote activation, the GD00Z-4 will allow user to try to operate the door one more time. If the second attempt fails, the GD00Z-4 will go into lock-out mode. See Note #3.
➓
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE
Unable to include in
Z-Wave network.
GD00Z-4 was not properly excluded from a previous
Z-Wave network.
3. If the GD00Z-4 is in lock-out mode and will not accept remote commands, activate the door from the pushbutton wall console.
4. Once the GD00Z-4 has initiated the movement of the garage door, another command cannot be sent for 30 seconds. This eliminates the chance of “bouncing” the garage door and possibly damaging the garage door opener.
The GD00Z-4 does not fl ash or beep when activated.
No power to the
GD00Z-4.
The GD00Z-4 fl ashes and beeps when activated but the door does not move.
Obstruction blocking the door or incorrect wiring.
Output: 12 VDC, 2 A
Operating Temperature: -4º—122° F (-20º—50° C)
Audible 45 db @ 10 feet
the ceiling, or bracket to the
opener’s hanging hardware
NOTICE TO USERS IN CALIFORNIA - CR COIN
CELL LITHIUM BATTERY INFORMATION: THIS
PRODUCT CONTAINS A CR COIN CELL LITHIUM
BATTERY WHICH CONTAINS PERCHLORATE
MATERIAL - SPECIAL HANDLING MAY APPLY - SEE www.dtsc.ca.gov/hazardouswaste/perchlorate
Tilt Sensor Specifi cations
Operating Temperature: -4º—122° F (-20º—50° C)
KEEP AWAY FROM SMALL CHILDREN. IF BATTERY
IS SWALLOWED, PROMPTLY SEE A DOCTOR. DO
NOT TRY TO RECHARGE THIS BATTERY. DISPOSAL
OF USED BATTERIES MUST BE MADE IN
ACCORDANCE WITH THE WASTE RECOVERY AND
RECYCLING REGULATIONS IN YOUR AREA.
Garage door opens or closes, but the status does not change on the
Z-Wave Controller.
The tilt sensor signal is not being received by the
GD00Z-4.
Mounting to Garage Door: Double-sided tape or two mounting screws
(Specifi cations subject to change without notice)
CORRECTIVE ACTION
1. Reset the GD00Z-4 by pressing the LINK button 5 times. A quick beep followed by a longer beep will indicate the reset.
1. Make sure the power supply is plugged in securely to a live outlet.
2. Make sure the power cord is plugged in securely to the
GD00Z-4.
1. Make sure that there are no obstacles preventing the door from moving.
2. Make sure that the GD00Z-4 connection wires are connected to the proper terminals on the garage door opener. Trace the wires from the garage door opener’s pushbutton wall console to the door opener. This is where the GD00Z-4 connection wires should be connected.
1. Make sure the tilt sensor is mounted correctly on the garage door, with the arrow pointing up.
2. Make sure the battery pull tab has been removed from the tilt sensor.
3. Replace the battery in the tilt sensor.
2 To synchronize the system, use the garage door opener's pushbutton to manually open and close the door
3 Use your Z-Wave Controller to activate your garage door opener
4 The GD00Z-4 will beep and flash for five seconds before the door moves
5 The GD00Z-4 will activate the door opener and open or close the door
Copyright © 2014 Linear LLC
BEEP
BEEP
BEEP
FLASH
FLASH
FLASH
STAY CLEAR
OF THE DOOR !!!
STAY CLEAR
OF THE DOOR !!!
LINEAR LIMITED WARRANTY
This Linear product is warranted against defects in material and workmanship for twelve (12) months. This warranty extends only to wholesale customers who buy direct from Linear or through Linear’s normal distribution channels. Linear does not warrant this product to consumers.
Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any.
There are no obligations or liabilities on the part of Linear LLC for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or profi t, or cost of removal, installation,
or reinstallation. All implied warranties, including implied warranties for merchantability and implied warranties for fi tness, are valid only until the warranty expires. This Linear LLC Warranty is in lieu of all other warranties express or implied.
All products returned for warranty service require a Return Product Authorization Number (RPA#).
Contact Linear Returns at 1-855-546-3351 for an RPA# and other important details.
REGULATORY NOTICES
This device complies with FCC Part 15 and Canada Rules and Regulations. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Changes or modifi cations not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
Les changements ou modifi cations non approuvés expressément par la partie responsable de la conformité pourrait annuler l’autorité de l’utilisateur à faire fonctionner l’équipement.
236956 X9
