XL 3100 V
HYDRAULIC EXCAVATOR
SPECIFICATIONS
Undercarriage
4 x 2 or 4 x 4
Wheelbase: 160” (4.06 m)
Width 102” (2.6 m)
Frame:
48” (1.2 m) wide, welded plate design
65 ksi material.
Gross Vehicle Axle Weight Rating:
4x2
41,250 lb (18,711 kg)
4x4
44,250 lb (20,071 kg)
Front Axles:
4 x 2: Meritor Model MFS-16-122A, 16,000 lb
(7,257 kg) rating.
4 x 4: Meritor Model MX19-145, 19,000 lb
(8,618 kg) rating, 7.17 ratio.
Rear Axle:
Meritor Model RS25-160, 25,250 lb (11,453 kg)
rating. 7.17 ratio, single reduction with driver
controlled differential lock.
Suspension:
Front: 8 leaf spring with automatic
lock-out cylinders.
Rear: Solid mount.
Brakes:
4 x 2 Front: Meritor “Q” Series Cam-Master
Size: 16.5” x 5” (419 mm x 152 mm)
Automatic Slack Adjusters.
4 x 4 Front: Meritor “Q” Series Cam-Master
Size: 16.5” x 6” (419 mm x 127 mm)
Automatic Slack Adjusters.
4 x 4 Rear and 4 x 2 Rear: Meritor “P”
Series Cam-Master
Size: 16.5” x 7” (419 mm x 178 mm)
Automatic Slack Adjusters.
Spring brake system incorporates emergency
and parking brakes on the rear axle.
Wheels:
Hub piloted disc 10-stud, 11.25” (286 mm)
bolt circle.
Tires:
4 x 4 front: 425/65R22.5 LR (L) on/off highway
traction tread
4 x 2 front: 385/65R22.5 LR (J) on/off
highway tread
4 x 2 and 4 x 4 rear: 11R24.5 LR (H) on/off
highway traction tread
Steering:
Ross, integral hydraulic power steering. Gear
type power steering pump. 4-quart power
steering reservoir with filter and 10 Micron
pre-filter.
Standard Chassis Equipment:
Halogen headlights, tail lights, back-up lights
and alarm, stoplights, identification lights front
and rear, directional lights, 4-way hazard lights,
work lights and instrument panel lights.
Windshield wiper/washer, West Coast style
mirror system with plane and convex mirrors,
front and rear tow hooks, desiccant type air
dryer with automatic purge valve and
thermostatically controlled heater.
Hydraulic System
PUMPS
One load-sensing axial piston pump; 8-55
GPM (30-208 L/min) total.
One gear pump (pilot and steering) 15gpm
(57 L/min.)
Filtration System:
5 micron return filter with magnet. 10 micron
pilot filter.
Plate - Fin/Fin oil cooler with thermostatically
controlled cooling fan.
Pressure-compensated, load-sensing valves
with circuit reliefs in all circuits.
Chassis Cab
One-person cab, left-hand mount, isolated
from frame on rubber mounts. Acoustical
lining. Sun visor. Gauges for oil pressure,
coolant temperature, air tank pressures, fuel
level, DEF level, voltmeter, speedometer with
odometer, tachometer, hour meter. Engine and
transmission monitor lights. Engine shutdown
controlled by engine electronics. Indicator
lights and controls for front axle engagement
(4 x 4 only) and rear axle differential lock. Park
brake control. Tinted safety glass. Sliding side
windows. Fresh air heater and defroster. Dome
light. Air suspension seat with seat belt. Vent
in door.
SYSTEM SPECIFICATIONS
Four Double Acting Cylinders:
• 2 hoist cylinders: 3.5” x 2.56” rod x
31” stroke (89 mm x 65 mm x 787 mm)
• 1 tool cylinder: 4.25” bore x 3.0” rod x
25.9” stroke (108 mm x 76 mm x 658 mm)
• 1 telescope: 3.5” ID x 2.559” rod x
11’ stroke (89 mm x 65 mm x 3.34 m)
Three Hydraulic Motors:
Swing, 51 Hp (38kW); tilt, 21 Hp (16kW); remote
drive, 110 Hp (82kW) total.
Operating Pressures:
Hoist........................................................ 4,800 psi (331 BAR)
Tilt............................................................... 2,500 psi (172 BAR)
Swing..................................................... 3,000 psi (206 BAR)
Tool........................................................... 4,800 psi (331 BAR)
Telescope........................................ 4,800 psi (331 BAR)
Remote Propel.......................... 4,800 psi (331 BAR)
Pilot system.........................................550 psi (38 BAR)
Oil Capacity:
Reservoir 50 gallons (189 L), system 65
gallons (246 L). Pressurized reservoir with
visual oil level gauge.
Upperstructure Cab
All-weather cab isolated from frame on
rubber mounts. Tinted safety glass windows,
skylight, acoustical lining, four-way adjustable
operator’s seat, dome light, filtered air heater
and defroster. AM/FM Radio, air conditioning,
work light package.
The heat source is provided by a fast
response, closed circuit hydraulic heater
with 20,000 BTU/Hr. capacity.
Front window slides to overhead storage.
Rearview mirrors on right and left sides of the
machine. Windshield wiper and washer.
Hydraulic Remote Control
Upperstructure powered by chassis hydraulics
through hydraulic motor and transfer case.
Travel and steering pedals in upperstructure
cab. Digging brakes and front axle lockout
cylinders set automatically with travel pedal in
neutral. Parking brakes controlled by toggle.
Electrically operated alarm mounted on
undercarriage signal remote control movement
in either direction, reverse movement when
driven from undercarriage cab.
XL 3100
310 V
0 VHighway Speed Wheeled Excavators
XL
XL 3100 V
Fuel Tank Capacity: 100 gal (378 L)
Engine
Volvo TAD572VE Tier 4f 5.1L diesel with
Selective Catalytic Reduction and cooled EGR
technology. 4 cycle, inline 4 cylinder, liquid
cooled. Turbo charge air aftercooled. Off-road
certified, electronically controlled, Grid heater.
Vertical canister style lube filter attached to
engine. Vertical canister style main fuel filter
attached to engine. Volvo remote mount vertical
style fuel/water separator with water in fuel
indicator, alarm and manual feed pump.
Gross Rating: 215 hp @ 2300 RPM. 660 ft lb
torque @ 1200-1700 RPM.
Net Rating: 198 hp @ 2300 RPM.
Air Filter: 2-stage Donaldson PSD PowerCore
with high efficiency pre-cleaner, vacuator value
and remote service indicator.
Electrical System: 24 volt, 110 amp alternator
with integral voltage regulator. 2 SAE #C31-S
1000 CCA batteries.
Chassis Cooling Package: Consists of
three aluminum bar-plate type coolers stacked
vertically: an air-air charge air cooler, radiator
and a transmission cooler. All three coolers
are backed by a molded fan shroud, engine
mounted fan ring and 26.8” nine-blade fan
driven by a Volvo electronically controlled
variable speed fan drive.
Upperstructure Controls
Urea Tank Capacity: 11.9 gal (45L)
Two electronic joysticks (hoist and bucket,
telescope and swing), one rocker switch (tilt)
control. Joysticks are mounted on arm pods that
are adjustable for individual operator comfort
and convenience. Quick change joystick pattern
switch located on instrument panel.
Transmission: Allison 3500 RDS 6-speed
automatic.
Gear Speeds: (with 11R24.5 tires)
Gear
1
2
3
4
5
6
MPH
6.5
15.5
22.7
34.9
46.6
60.0
Km/hr
(10.4)
(25.0)
(36.5)
(56.1)
(75.0)
(96.6)
Gear
REV
MPH
6.3
Km/hr
(10.1)
Two foot pedals for remote control of
undercarriage steering, travel and
digging brakes.
Joysticks and pedals are self-centering; when
controls are released, power for movement
disengages and swing and travel brakes set
automatically.
Drivelines: Spicer 1710 Series with
“Half Round” yokes.
Transfer Case: (4 x 2) Cushman Model 479-1,
1:1 Ratio, Pneumatic engage for Remote Propel.
(4 x 4) Cushman Model 479A-1, 1:1 Ratio,
Pneumatic engage for Remote Propel
and Front Drive.
Engine Controls
Key ignition switch with neutral start and
indicator lights for low air, engine status, park
brake, travel status, hydraulic fluid temperature
and level.
Automatic engine shutdown occurs with low oil
pressure, derate/shutdown for oil temperature,
coolant temperature, coolant level, ERD
temperature, change air temperature, change
air pressure and derate for SCR temperature.
Swing
Priority swing circuit with axial piston motor.
Planetary transmission.
Swing speed: 8 RPM.
Swing brake: Automatic spring-set/hydraulic
release wet disc parking brake. Dynamic
braking is provided by the hydraulic system.
GRADALL Model XL 3100 V Lift Capacity Over Side or Rear - LB. (KG.)
LOAD RADIUS
LOAD
POINT HEIGHT
10’ 0” (3.0 m)
Over End
Over Side
15’ 0” (4.6 m)
Over End
Over Side
20’ 0” (6.1 m)
Over End
Over Side
20’ 0” (6.1 m)
ABOVE
GROUND
LEVEL
Over Side
Maximum
radius
Over End
Over Side
20’ 2”
(6.1 m)
3625
(1645)
3625
(1645)
15’ 0” (4.6 m)
6475
(2935)
6475
(2935)
4320
(1960)
4320
(1960)
22’ 8”
(6.9 m)
3545
(1610)
3545
(1610)
10’ 0” (3.0 m)
7655
(3470)
7655
(3470)
4890
(2220)
4890
(2220)
24’ 0”
(7.3 m)
3560
(1615)
3560
(1615)
7840
(3555)
7840
(3555)
4975
(2255)
4975
(2255)
24’ 2”
(7.4 m)
3575
(1620)
3575
(1620)
7870
(3570)
7870
(3570)
5050
(2290)
5050
(2290)
24’ 2”
(7.4 m)
3625
(1645)
3625
(1645)
6840
(3105)
6840
(3105)
4710
(2135)
4710
(2135)
23’ 3”
(7.1 m)
3720
(1685)
3720
(1685)
4030
(1830)
4030
(1830)
21’ 0”
(6.4 m)
3785
(1715)
3785
(1715)
16’ 11”
(5.1 m)
3665
(1660)
3665
(1660)
9’ 9”
(3 m)
2155
(975)
2155
(975)
BOOM LEVEL
8’ 6” (2.6 m)
5’ 0” (1.5 m)
AT GROUND LEVEL
BELOW
GROUND
LEVEL
25’ 0” (7.6 m)
Over End
5’ 0” (1.5 m)
5920
(2685)
5920
(2685)
5920
(2685)
5920
(2685)
15’ 0” (4.6 m)
3590
(1630)
3590
(1630)
3860
(1750)
3860
(1750)
10’ 0” (3.0 m)
NOTE: The above loads are in compliance with the SAE standard J1097 DEC2005. They do not exceed 87% of hydraulic lifting capacity or 75% of tipping capacity.
The rated lift capacity is based on the machine being equipped with
6,000 lb (2720 kg) counterweight, standard boom, standard tires, no
auxiliary hydraulics and no bucket.
Adjust the listed rated capacities by subtracting the value listed for
bucket/attachment used:
Ditching- 807 lbs (366 kg)
8065-6007 60” (1.5 m)
Ditching- 892 lbs (405 kg)
8065-6006 66” (1.7 m)
8065-6002 72” (1.8 m)
Ditching- 944 lbs (428 kg)
8045-6020 24” (610 mm)
Excavating- 603 lbs (274 kg)
8045-6021 30” (762 mm)
Excavating- 660 lbs (300 kg)
Excavating- 741 lbs (336 kg)
8045-6022 36” (914 mm)
Excavating- 841 lbs (382 kg)
8045-6023 42” (1.1 m)
8045­- 6024 48” (1.2 m)
Excavating- 957 lbs (434 kg)
8065-6013 72” (1.8 m)
Dredging- 1114 lbs (505 kg)
8065-6102 40” (1.0 m)
Pavement- 1262 lbs (573 kg)
8065-6024 8” (2.4 m)
Blade- 630 lbs (285 kg)
8065-6009 Single Tooth
Ripper- 557 lbs (253 kg)
NOTE: Bucket adjustment values are 87% of the actual bucket weights.
The load point is located on the bucket pivot point, including load listed
for maximum radius.
Do not attempt to lift or hold any load greater than these rated values at
specified load radii and heights. The weight of slings and any auxiliary
devices must be deducted from the rated load to determine the net load
that may be lifted.
ATTENTION: All rated loads are based on the machine being stationary
and level on a firm supporting surface. For safe working loads, the user
must make allowance for his particular job conditions such as soft or
uneven ground, out of level conditions, side loads, hazardous conditions,
experience of personnel, etc. The operator and other personnel must
fully acquaint themselves with the Operator’s Manual furnished by the
manufacturer before operating this machine. Rules for safe operation of
equipment must be adhered to at all times.
Shown with 8035-6006 48” (1.2 m) excavating bucket
4 x 2 4 x 4
4 x 2
A
27’ 6” (8.4)
A1 23’ 3” (7.1)
27 ’6” (8.4) Overall length (boom in rack) with bucket
23’ 3” (7.1)Overall length (boom in rack)
without bucket
B 11’ 11” (3.6) 12’ 3” (3.7) Overall height (boom in rack) with bucket
B1 11’ 1” (3.4)
11’ 5” (3.5)Overall height (boom in rack)
without bucket
C1 8’ 6” (2.6)
8’ 6” (2.6) Width of upper structure
C3 8’ 6” (2.6)
8’ 6” (2.6) Width of undercarriage
D 2” (45 mm) 2” (45 mm)Minimum clearance, upperstructure to
undercarriage
E
7’ 6” (2.3)
7’ 6” (2.3) Swing clearance, rear of upperstructure
F 10’ 10” (3.3) 11’ 1” (3.4) Top of cab to ground line
G
50” (1.3)
54” (1.4)
Clearance, upperstructure to ground line
H
44” (1.1)
47” (1.2)Top of wheel mounted undercarriage
frame to ground line
L
21’ 0” (6.4)
21’ 0” (6.4) Overall length of undercarriage
N 10” (254 mm) 10” (254 mm) Ground clearance (per SAE J1234)
P 28” (701 mm) 28” (701 mm) Center of rear axle to axis of rotation
R
13’ 4” (4.1)
13’ 4” (4.1) Wheel base
S 36” (916 mm) 36” (916 mm) Center of rear axle to rear of frame (step)
V1 6’ 6” (2.0)
6’ 6” (2.0) Tread, rear axles 4 x 4 (10:00 x 20 tires),
4 x 2 (Spoke Wheels)
V2 7’ 0” (2.1)
7’ 0” (2.1)Tread, front axle 4 x 4 (15:00 x 22.5 tires),
4 x 2 (Spoke Wheels)
AA 27’ 3” (8.3)
27’ 2” (8.3)Maximum radius at ground line (165° pivot)
AB 18’ 4” (5.6)
18’ 1” (5.5) Maximum digging depth (165° pivot)
AC 16’ 6” (5.0)
16’ 3” (4.9) Maximum depth for 8’ level cut
AD 6’ 3” (1.9)
6’ 3” (1.9)Maximum radius of 8’ level cut at depth “AC”
AF 1’ 10” (0.6)
1’ 10” (0.6)Maximum depth of vertical wall which
can be excavated
AG 11’ 0” (3.3)
10’ 11” (3.3)Minimum level cut radius with bucket flat
on ground line
AH 5’ 11” (1.8)
5’ 4” (1.6) Minimum radius at ground line
AK 6’ 6” (2.0)
6’ 10” (2.1) Boom pivot to ground line
4x4
AL 23” (596 mm) 23” (596 mm) Boom pivot to axis of rotation
AP 46” (1.2)
46” (1.2)
Bucket tooth radius
AQ 30° Up & 30° Up & Boom pivot angle
75° Down
75° Down
AS
165°
165°
Bucket pivot angle
AU 22’ 3” (6.8)
22’ 3” (6.8)Maximum telescoping boom length
(boom pivot to bucket pivot)
AV 11’ 3” (3.4)
11’ 3” (3.4)Minimum telescoping boom length
(boom pivot to bucket pivot)
AW 11’ 0” (3.4)
11’ 0” (3.4) Telescoping boom travel
AX
110°
110°
Bucket tilt angle (both sides of center)
BA 28’ 1” (8.6)
28’ 1” (8.6) Maximum radius of working equipment
BB 22’ 7” (6.9)
22’ 11” (7.0)Minimum clearance of bucket teeth, with
bucket pivot at maximum height
BC 20’ 8” (6.3)
21’ 0” (6.4) Maximum bucket tooth height
BD 15’ 5” (4.7)
15’ 9” (4.8)Minimum clearance of bucket teeth, with
bucket pivot at maximum height
BE 10’ 5” (3.2)
10’ 9” (3.3)Minimum clearance of fully curled bucket
at maximum boom height
BF 10’ 1” (3.1)
10’ 4” (3.2)Minimum clearance of bucket teeth at
maximum boom height
BG 14’ 11” (4.5)
15’ 2” (4.6)Maximum height of working equipment
with bucket below ground line
BH 23’ 11” (7.3) 23’ 11” (7.3) Radius of bucket teeth at maximum height
BJ 17’ 3” (5.3)
17’ 3” (5.3)Minimum radius of bucket teeth at
maximum bucket pivot height
Rated boom force: 21,940 lb (97.6kN)
Rated bucket breakout force: 17,990 lb (80kN)
Weight: Approximate working weight, including 30” (762 mm) bucket,
fuel tank half full.
4 x 2: 40,930 lb (18,566 kg)
4 x 4: 41,720 lb (18,924 kg)
Specifications subject to change without notice.
Metric units are meters (m) unless noted.
Machines shown may have optional equipment.
Optional Equipment
Vandalism protection kit including
window covers.
Strobe light.
ROPS protective cab (upper cab only)
Auxiliary Hydraulics - Additional hosing and
piping for hydraulic powered attachments.
[Maximum pressure 4800 psi (33,095 kPa)
Maximum flow 30 GPM (114 L/min)]
Attachments
Quick change and reversible buckets
fabricated of steel plate, with high strength,
low alloy cutting edges and wear strips.
Standard attachments available for wide
range of applications. Capacities shown are
in heaped cu. yd.
Cu.
yd.m3
8045-6020 24” (610 mm)
Excavating bucket
3/8
0.31
8045-6021 30” (762 mm)
Excavating bucket
1/2
0.41
8045-6022 36” (914 mm)
Excavating bucket
5/8
0.54
8045-6023 42” (1.07 m)
Excavating bucket
3/4
0.64
8045-6024 48” (1.22 m)
Excavating bucket
1
0.76
8065-6013 72” (1.83 m)
Dredging bucket
Cu.
yd.
m3
1 1/8
0.87
8065-6024 8’ (2.4 m) Grading blade
8065-5028 4’ (1.2 m) Boom extension
Cu.
yd.m3
8065-6104 15” (381 mm)
Trenching bucket
1/5
0.15
8065-6012 21” (533 mm)
Trenching bucket 1/4
0.19
8045-5052 Tree limb shear attachment
8065-6102 40” (1.02 m)
Pavement removal bucket
8065-6115 18” (0.457 m)
Pavement removal bucket
8065-6116 24” (0.610 m)
Pavement removal bucket
8065-611 28” (0.711 m)
Pavement removal bucket
It is Gradall Policy to continually improve its
products. Therefore designs, materials and
specifications are subject to change without
notice and without incurring any liability on
units already sold. Units shown may have
optional equipment.
406 Mill Ave. SW, New Philadelphia, Ohio 44663
Phone: 330-339-2211 Fax: 330-339-8468
www.Gradall.com
Form No. 11702 2/17
Printed in USA
Certified ISO 9001
8045-5009 6’ (1.8 m) Live boom
Cu.
yd.m3
8065-6040 30” (0.762 m)
Ditching bucket
3/8
0.3
8065-600 60” (1.52 m)
Ditching bucket
7/8
0.73
8065-6006 66” (1.68 m)
Ditching bucket
1
0.76
8065-6002 72” (1.83 m)
Ditching bucket
1 1/8
0.87
8075-5023 Fixed thumb grapple
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement