UN7200 - Rosen Electronics

UN7200 - Rosen Electronics
OPERATING
INSTRUCTIONS
e11 022771
Headrest 7.0" 16:9 Color Display Monitor
Important Notice
It is unlawful in most jurisdictions for a person to drive a motor vehicle which is
equipped with a television or screen that is located in the motor vehicle at
any point forward of the back of the driver's seat, or that is visible directly
or indirectly to the driver while operating the vehicle.
CAUTION
1.
2.
3.
4.
Do not expose to direct sunlight for extended periods of time.
Do not drop the monitor or expose to strong impacts.
Keep the monitor clean and dry.
Do not operate the monitor at temperatures below 32°F (0°C) or above 140°F (60°C).
9100768
Installation Guide:
The kit includes a protective trim ring and an optional spacer ring for use when the mounting
surface is uneven.
1. Select appropriate locations in your vehicle for the monitor .
2. Be sure there is sufficient depth for the trim ring. Add the spacer ring for shallow locations
with uneven curved surfaces such as upholstery. Be sure there is enough space for both
the trim ring and for any excess interconnect cable.
3. Ensure that the interconnect cable will reach from the monitor location .
4. Create the required opening for the monitor and trim ring. Be sure it is not too large, and
that there is enough space behind the trim ring to store any excess interconnect cable.
Excess cable does not fit within the trim ring.
5. Route the cable through the opening in the trim ring
6. Connect the cable to the monitor.
7. Securely snap the monitor into place.
MONITOR
HEADREST SHROUD
TRIM RING
WIRE IN TUBE
Cable
If you need to remove the monitor from the trim ring, insert a credit card between the monitor and
the trim ring to release the monitor from the flexible locking retainer tabs. Gently pull the monitor
from the trim ring. Very gentle pressure can be applied using the credit card.
01
Electrical Connections:
Black
Black
Gray
Gray
Black --- GND
Yellow ---Power
Red --- ACC
Power output cable
OUT 2
A (R) A (L) V
Red---13.2V / Black---GND
OUT 1
Remote Out
Remote
IN 2
A (L) A (R) 1 2
A (R) A (L) V
IN 1
A (L) A (R) V
RED-ACC
YELLOW-BATTERY
BLACK-GND
2 PIN
2 PIN
AUX 1B+ AUX 2B+
(To TV-Tuner/DVD Changer)
POWER CORD
14 PIN
TO MONITOR(B)
14 PIN
TO MONITOR(A)
V
(To TV-Tuner/DVD Changer)
Note: Please make sure all cables are
connected correctly, wrong connections
will damage the monitor.
02
Basic Operation:
Front Control Panel:
1. LCD Panel
2. Headrest Shroud
3. POWER : ON / OFF / AUX Selection and
Enter button (press and hold the button will power off)
8. IR Transmitter
4. UP : Positive and Negative Adjustment
5. MENU : Activation of Menu Indicator
7. Infrared Remote
Controller Receiver
6. DOWN : Positive and Negative Adjustment
B
Off
A
IR-A(L-2.3MHZ,R-2.8MHZ)
IR-B(L-3.2MHZ,R-3.8MHZ)
03
REMOTE CONTROL:
1
4
5
2
3
6
7
8
9
RES
10
11
SOURCE
12
13
ENTER
16
15
20
CH
SOURCE
MENU
17
NEXT
DISC
INFO
EJECT
14
CH
SUB
TITLE
DISC
MENU
18
OUTPUT
B
DISC
ZOOM
19
DISPLAY
MODE
ROSEN
USING THE REMOTE CONTROL
You can use the remote control to operate the system, including access to features
not available on the front panel.For definitions of each remote control button’s
specific function, see the following pages.
1
2
3
4
5
6
7
8
9
10
11
Power On/Off (TV-TUNER / DVD Changer / Single disk DVD )
Stop ( Ext DVD )
12 Navigate left
Play / Pause ( Ext DVD )
13 Enter
Previous Chapter/Track ( Ext DVD )
14 Navigate Right
Reverse ( Ext DVD )
15 Source Setup Menu- Auto Tune
Fast forward ( Ext DVD )
(TV Tuner only)
Next Chapter/Track ( Ext DVD )
16 Navigate Down
Mute (On / Off)
17 Dimmer (Day/Night Mode)
Next Disc ( Ext DVD )
18 Output B Control (Tuner only)
Source select
19 Display Mode
Navigate Up
20 INFO ( Ext DVD )
Note: If you try to perform a DVD action when it is not permitted (such as accessing the disc
menu while the disc is loading), there will be no response from the unit. This is normal operation
and is not a problem with your system.
04
BASIC REMOTE CONTROL BUTTONS:
1
TV-Tuner / DVD Changer (POWER)
Pressing this POWER (
) button will turn the unit on. If unit off, a
single press should turn the unit on. Otherwise once the unit is on,
a single press should change source.
2
Stop
Press once to temporarily stop playback of a DVD. To resume normal
playback from the same point, press PLAY.
To play the disc from the beginning, press STOP twice, then PLAY.
3
Play/Pause
Press to begin or resume playback of a DVD.
Press once to pause playback. Press repeatedly to advance video
frame by frame. To resume normal playback, press PLAY.
Note: When the disc is first inserted, you may have to press
PLAY or ENTER to begin playback.
4
Previous Chapter/Track
Press to jump to the previous title or chapter, if available on a DVD, or
to the previous track on an audio CD. Not supported with some VCDs.
5
Reverse
Press to search in reverse. To resume normal playback, press PLAY.
05
BASIC REMOTE CONTROL BUTTONS:
6
Forward/Search
Press during playback to fast forward. Press the RIGHT and LEFT
arrow buttons to adjust search direction and speed. Choose from 2x,
4x, 6x, and 8x. Press PLAY to resume regular play.
7
Next Chapter/Track
Press to jump to the next title or chapter, if available on a DVD, or to
the next track on an audio CD. Not supported with some VCDs.
8
Mute
Press once to mute all system audio. As long as the Mute function is
active, “Mute” will appear on the screen. Press again to turn Mute off.
9
Next Disc
NEXT
DISC
When the optional R5006 DVD Changer is connected, this button
commands the changer to play the next disc in the magazine.
10 Source
SOURCE
This button lets you select the internal DVD/CD player, the Internal
Game, or the Auxiliary input. You can also select the optional TV
Tuner, DVD Changer, or other optional auxiliary sources, if installed.
11, 16
Navigate Up/Down Arrows
Press to move up or down in a menu or to change channel when
watching TV.
06
BASIC REMOTE CONTROL BUTTONS:
12, 14
Left/Right Arrows
Press to move left or right in a menu.
13 Enter
ENTER
Press to make a menu selection.
15 Source Menu
SOURCE
MENU
If the source unit selected has a Setup Menu, you can access it by
pressing Source Menu. With the optional TV Tuner, this button
activates the Auto-Program feature, which stores all available TV
stations in the memory for easier, faster channel-changing.
17 DIMMER (Day/Night Mode)
This button decreases display brightness for optimum viewing in low
light conditions.
Set the Brightness level in daytime conditions with plenty of ambient
light, and with the headlights off. Then you can use this button to
switch between Day and Night modes.
19 Display Mode
DISPLAY
MODE
This button lets you select from the various screen display modes.
INSTALL SETUP:
Press remote control "EJECT
INSTALL
AUX1
AUX2
ENTER
INFO
ENTER" button on remote to setup system
SETUP
INSTALL
AUX1
AUX1
DVD Changer
AUX2
External Game
SETUP
AUX2
DVD Changer
External Game
Satellite
Satellite
TV Tuner
TV Tuner
07
BASIC REMOTE CONTROL BUTTONS:
20 INFO
INFO
Press to view the status, current title number, track number and the total
playing time of the currently-playing disc.
REPLACING THE REMOTE BATTERY
Battery
Press tab here
and pull battery tray out
Use a single 3V battery, type CR2025. Insert as shown. Observe the
correct orientation of the battery as marked on the battery tray.
Battery life is approximately six months, depending on how often the
remote is used.
08
On-Screen-Display Settings:
MODE:
When monitor is power on, press mode button control panel to select video inputs AV1/AV2
NTSC/PAL. (Press and hold power button on control panel will power off the monitor.)
MONITOR SETTINGS:
Press the Menu button control panel, the OSD menu will show the LCD screen as below, use the
menu button on front control panel to select setting .
1
4
5
2
3
6
7
8
9
RES
10
NEXT
DISC
11
SOURCE
12
ENTER
16
15
INFO
CH
13
SOURCE
MENU
17
EJECT
14
CH
SUB
TITLE
DISC
MENU
18
OUTPUT
B
DISC
ZOOM
19
DISPLAY
MODE
ROSEN
COLOR:
Press Menu button control panel, OSD menu will show on LCD screen as below (left chart), press
menu button control panel to select "COLOR" setting, "COLOR" setting will show as below
(right chart).
BRIGHT:
Press Menu button on control panel, OSD menu will show on LCD screen as below (left chart) ,
"BRIGHT" setting will show as below (right chart).
COLOR
> BRIGHT
TINT
DIMMER
FORMAT
RESET
MODE
MENU
BRIGHT
09
50
On-Screen-Display Settings:
TINT:
Press Menu button on control panel, OSD menu will show on LCD screen as below
(left chart),and hold up/down button on control panel to select "TINT" setting.
"TINT" setting will show as below (right chart).
COLOR
BRIGHT
> TINT
DIMMER
FORMAT
RESET
MODE
MENU
TINT
50
DIMMER:
Press Menu button on remote or on control panel, OSD menu will show on LCD
screen as below (left chart), press up/down button on remote or press and hold
up/down button on control panel to select "DIMMER" setting. "DIMMER" setting
will show as below (right chart).
COLOR
BRIGHT
TINT
> DIMMER
FORMAT
RESET
MODE
MENU
DIMMER
ON
OFF
DISPLAY MODE: (FORMAT)
Press Menu button on remote or on control panel, OSD menu will show on LCD
screen as below (left chart), press up/down button on remote or up/down botton
on control panel to selet "FORMAT" setting, Press enter button on or power button
on control panel to select "FORMAT" setting, NORMAL/ PANORAMA/ ZOOM/ FULL
display mode ."FORMAT" setting will show as below (right chart).
COLOR
BRIGHT
TINT
DIMMER
> FORMAT
RESET
MODE
MENU
FORMAT
NORMAL
10
On-Screen-Display Settings:
RESET IMAGE:
Press Menu button on control panel, OSD menu will show on LCD screen as below (left chart),
press up/down button on control panel to select "RESET" setting. Press enter button on power
button on control panel to select "RESET" setting,"RESET" setting will show as below (right chart).
COLOR
BRIGHT
TINT
DIMMER
FORMAT
> RESET
MODE
MENU
RESET
Installation Notes:
The Wide Screen Universal Monitor includes mounting options described in the
following sections. Before you install the monitor, consider the following
important notices:
1. NEVER install this monitor where it can be viewed from the driving position;
this is a violation of many state and local vehicle codes.
2. Avoid mounting locations where there is a risk of impact with a passenger in
the event of an accident.
3. Always mount the monitor securely using the mounting hardware that is
provided. Do not use the monitor unless it is properly secured to the vehicle.
Box Contents:
The Widescreen Universal Monitor includes the following parts and equipment:
1. Monitor x2
2. Remote Control x1
3. Power input cable (YEL/RED/BLK) x1
4. Monitor to junction box harness (BLK/GRY) x2
5. Power output cable (RED/BLK) x2
6. Junction box x1
11
7. Flush mounting trim ring x2
8. Headrest shroud x2
9. Manual x1
10. IR remote cable x2
11. RCA cable x2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement