Turbosound TCX122 Quick Start Guide

TCX82 / TCX82-WH
TCX102 / TCX102-WH
TCX122 / TCX122-WH
TCX152 / TCX152-WH
TCX115B / TCX115B-WH
TCX118B / TCX118B-WH
Loudspeakers for Portable PA and
Installation Applications
Quickstart Guide
2
TCX series
Important Safety
Instructions
Terminals marked with this
symbol carry electrical
current of sufficient magnitude
to constitute risk of electric shock. Use only
high-quality commercially-available speaker
cables with plugs pre-installed. All other
installation or modification should be
performed only by qualified personnel.
This symbol, wherever it
appears, alerts you to the
presence of uninsulated
dangerous voltage inside the enclosure voltage that may be sufficient to constitute
a risk of shock.
This symbol, wherever it
appears, alerts you to important
operating and maintenance
instructions in the accompanying literature.
Please read the manual.
Caution
To reduce the risk of electric
shock, do not remove the
top cover (or the rear section). No user
serviceable parts inside. Refer servicing to
qualified personnel.
Caution
To reduce the risk of fire or
electric shock, do not expose
this appliance to rain and moisture.
The apparatus shall not be exposed to
dripping or splashing liquids and no objects
filled with liquids, such as vases, shall be
placed on the apparatus.
Caution
These service instructions are
for use by qualified service
personnel only. To reduce the risk of
electric shock do not perform any servicing
other than that contained in the operation
instructions. Repairs have to be performed
by qualified service personnel.
1.
Read these instructions.
2.
Keep these instructions.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Do not use this apparatus near water.
6.
Clean only with dry cloth.
7. Do not block any ventilation
openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources
such as radiators, heat registers, stoves,
or other apparatus (including amplifiers)
that produce heat.
Quick Start Guide
9. Do not defeat the safety purpose of
the polarized or grounding-type plug.
A polarized plug has two blades with one
wider than the other. A grounding-type
plug has two blades and a third grounding
prong. The wide blade or the third
prong are provided for your safety. If the
provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being
walked on or pinched particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.
11. Use only attachments/accessories
specified by the manufacturer.
12. Use only with
the cart, stand,
tripod, bracket,
or table specified by
the manufacturer,
or sold with
the apparatus.
When a cart is used,
use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during lightning
storms or when unused for long periods
of time.
14. Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or has
been dropped.
15. The apparatus shall be connected to
a MAINS socket outlet with a protective
earthing connection.
16. Where the MAINS plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain
readily operable.
17. Correct disposal of
this product: This symbol
indicates that this product
must not be disposed of
with household waste,
according to the WEEE
Directive (2012/19/EU)
and your national law.
This product should be taken to a collection
center licensed for the recycling of waste
electrical and electronic equipment (EEE).
The mishandling of this type of waste could
have a possible negative impact on the
environment and human health due to
potentially hazardous substances that are
generally associated with EEE. At the same
time, your cooperation in the correct
disposal of this product will contribute to
the efficient use of natural resources.
For more information about where you can
take your waste equipment for recycling,
please contact your local city office, or your
household waste collection service.
LEGAL DISCLAIMER
MUSIC Group accepts no liability for any
loss which may be suffered by any person
who relies either wholly or in part upon
any description, photograph, or statement
contained herein. Technical specifications,
appearances and other information
are subject to change without notice.
All trademarks are the property of their
respective owners. MIDAS, KLARK TEKNIK,
LAB.GRUPPEN, LAKE, TANNOY,
TURBOSOUND, TC ELECTRONIC,
TC-HELICON, BEHRINGER, BUGERA, DDA
and TC APPLIED TECHNOLOGIES are
trademarks or registered trademarks of
MUSIC Group IP Ltd. © MUSIC Group IP
Ltd. 2015 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and
conditions and additional information
regarding MUSIC Group’s Limited
Warranty, please see complete details
online at music-group.com/warranty.
Instrucciones de
seguridad
4.
Siga todas las instrucciones.
5.
No use este aparato cerca del agua.
6.
Limpie este aparato con un paño seco.
7. No bloquee las aberturas de
ventilación. Instale el equipo de acuerdo
con las instrucciones del fabricante.
Las terminales marcadas con
este símbolo transportan
corriente eléctrica de magnitud
suficiente como para constituir un riesgo de
descarga eléctrica. Utilice solo cables de
altavoz de alta calidad con clavijas
TS de 6,3 mm pre-instaladas
(puede adquirirlos en comercios
especializados en audio). Cualquier otra
instalación o modificación debe ser
realizada únicamente por un
técnico cualificado.
Este símbolo, siempre que
aparece, le advierte de la
presencia de voltaje peligroso
sin aislar dentro de la caja; este voltaje
puede ser suficiente para constituir un
riesgo de descarga.
Este símbolo, siempre que
aparece, le advierte sobre
instrucciones operativas y de
mantenimiento que aparecen en la
documentación adjunta. Por favor,
lea el manual.
Atención
Para reducir el riesgo de
descarga eléctrica, no quite
la tapa (o la parte posterior). No hay
piezas en el interior del equipo que
puedan ser reparadas por el usuario.
Si es necesario, póngase en contacto con
personal cualificado.
Atención
Para reducir el riesgo de
incendio o descarga eléctrica,
no exponga este aparato a la lluvia,
humedad o alguna otra fuente que pueda
salpicar o derramar algún líquido sobre
el aparato. No coloque ningún tipo de
recipiente para líquidos sobre el aparato.
Atención
Las instrucciones de servicio
deben llevarlas a cabo
exclusivamente personal cualificado.
Para evitar el riesgo de una descarga
eléctrica, no realice reparaciones que no
se encuentren descritas en el manual de
operaciones. Las reparaciones deben
ser realizadas exclusivamente por
personal cualificado.
1.
Lea las instrucciones.
2.
Conserve estas instrucciones.
3. Preste atención a todas
las advertencias.
8. No instale este equipo cerca de
fuentes de calor tales como radiadores,
acumuladores de calor, estufas u otros
aparatos (incluyendo amplificadores) que
puedan producir calor.
9. No elimine o deshabilite nunca la
conexión a tierra del aparato o del cable
de alimentación de corriente. Un enchufe
polarizado tiene dos polos, uno de los
cuales tiene un contacto más ancho que
el otro. Una clavija con puesta a tierra
dispone de tres contactos: dos polos y
la puesta a tierra. El contacto ancho y el
tercer contacto, respectivamente, son
los que garantizan una mayor seguridad.
Si el enchufe suministrado con el equipo
no concuerda con la toma de corriente,
consulte con un electricista para cambiar la
toma de corriente obsoleta.
10. Coloque el cable de suministro de
energía de manera que no pueda ser pisado
y que esté protegido de objetos afilados.
Asegúrese de que el cable de suministro de
energía esté protegido, especialmente en la
zona de la clavija y en el punto donde sale
del aparato.
11. Use únicamente los dispositivos o
accesorios especificados por el fabricante.
12. Use únicamente
la carretilla,
plataforma, trípode,
soporte o mesa
especificados
por el fabricante
o suministrados
junto con el equipo.
Al transportar el
equipo, tenga cuidado para evitar daños y
caídas al tropezar con algún obstáculo.
13. Desenchufe el equipo durante
tormentas o si no va a utilizarlo durante un
periodo largo.
14. Confíe las reparaciones únicamente a
servicios técnicos cualificados. La unidad
requiere mantenimiento siempre que
haya sufrido algún daño, si el cable
de suministro de energía o el enchufe
presentaran daños, se hubiera derramado
un líquido o hubieran caído objetos dentro
del equipo, si el aparato hubiera estado
expuesto a la humedad o la lluvia, si ha
dejado de funcionar de manera normal o si
ha sufrido algún golpe o caída.
15. Al conectar la unidad a la toma de
corriente eléctrica asegúrese de que la
conexión disponga de una unión a tierra.
16. Si el enchufe o conector de red sirve
como único medio de desconexión,
éste debe ser accesible fácilmente.
3
17. Cómo debe
deshacerse de este
aparato: Este símbolo
indica que este aparato no
debe ser tratado como
basura orgánica, según lo
indicado en la Directiva
WEEE (2012/19/EU) y a las
normativas aplicables en su país. En lugar
de ello deberá llevarlo al punto limpio más
cercano para el reciclaje de sus elementos
eléctricos / electrónicos (EEE). Al hacer esto
estará ayudando a prevenir las posibles
consecuencias negativas para el medio
ambiente y la salud que podrían ser
provocadas por una gestión inadecuada de
este tipo de aparatos. Además, el reciclaje
de materiales ayudará a conservar los
recursos naturales. Para más información
acerca del reciclaje de este aparato,
póngase en contacto con el Ayuntamiento
de su ciudad o con el punto limpio local.
NEGACIÓN LEGAL
MUSIC Group no admite ningún tipo
de responsabilidad por cualquier
daño o pérdida que pudiera sufrir
cualquier persona por confiar total
o parcialmente en la descripciones,
fotografías o afirmaciones contenidas
en este documento. Las especificaciones
técnicas, imágenes y otras informaciones
contenidas en este documento están
sujetas a modificaciones sin previo
aviso. Todas las marcas comerciales
que aparecen aquí son propiedad
de sus respectivos dueños. MIDAS,
KLARK TEKNIK, LAB.GRUPPEN, LAKE,
TANNOY, TURBOSOUND, TC ELECTRONIC,
TC-HELICON, BEHRINGER, BUGERA,
DDA y TC APPLIED TECHNOLOGIES son
marcas comerciales o marcas registradas
de MUSIC Group IP Ltd. © MUSIC Group IP
Ltd. 2015 Reservados todos los derechos.
GARANTÍA LIMITADA
Si quiere conocer los detalles y condiciones
aplicables de la garantía así como
información adicional sobre la Garantía
limitada de MUSIC Group, consulte
online toda la información en la web
music-group.com/warranty.
4
TCX series
Quick Start Guide
6.
Consignes de sécurité
Les points repérés par ce
symbole portent une tension
électrique suffisante pour
constituer un risque d’électrocution.
Utilisez uniquement des câbles d’enceintes
de haute qualité disponibles dans les points
de vente avec les connecteurs Jack mono
6,35 mm déjà installés. Toute autre
installation ou modification doit être
effectuée uniquement par un
personnel qualifié.
Ce symbole avertit de la
présence d’une tension
dangereuse et non isolée à
l’intérieur de l’appareil - elle peut provoquer
des chocs électriques.
Attention
Ce symbol signale les
consignes d’utilisation
et d’entre ! Tien importantes dans la
documentation fournie. Lisez les consignes
de sécurité du manuel d’utilisation
de l’appareil.
Attention
Pour éviter tout risque de
choc électrique, ne pas ouvrir
le capot de l’appareil ni démonter le
panneau arrière. L’intérieur de l’appareil
ne possède aucun élément réparable par
l’utilisateur. Laisser toute réparation à un
professionnel qualifié.
Attention
Pour réduire les risques de feu
et de choc électrique, n’exposez
pas cet appareil à la pluie, à la moisissure,
aux gouttes ou aux éclaboussures.
Ne posez pas de récipient contenant un
liquide sur l’appareil (un vase par exemple).
Attention
Ces consignes de sécurité et
d’entretien sont destinées à un
personnel qualifié. Pour éviter tout risque
de choc électrique, n’effectuez aucune
réparation sur l’appareil qui ne soit décrite
par le manuel d’utilisation. Les éventuelles
réparations doivent être effectuées
uniquement par un technicien spécialisé.
1.
Lisez ces consignes.
2.
Conservez ces consignes.
3.
Respectez tous les avertissements.
4. Respectez toutes les consignes
d’utilisation.
5. N’utilisez jamais l’appareil à proximité
d’un liquide.
Nettoyez l’appareil avec un chiffon sec.
7. Veillez à ne pas empêcher la bonne
ventilation de l’appareil via ses ouïes
de ventilation. Respectez les consignes
du fabricant concernant l’installation
de l’appareil.
8. Ne placez pas l’appareil à proximité
d’une source de chaleur telle qu’un
chauffage, une cuisinière ou tout appareil
dégageant de la chaleur (y compris un
ampli de puissance).
9. Ne supprimez jamais la sécurité des
prises bipolaires ou des prises terre.
Les prises bipolaires possèdent deux
contacts de largeur différente. Le plus large
est le contact de sécurité. Les prises terre
possèdent deux contacts plus une mise à la
terre servant de sécurité. Si la prise du bloc
d’alimentation ou du cordon d’ali-mentation
fourni ne correspond pas à celles de votre
installation électrique, faites appel à un
électricien pour effectuer le changement
de prise.
10. Installez le cordon d’alimentation de
telle façon que personne ne puisse marcher
dessus et qu’il soit protégé d’arêtes
coupantes. Assurez-vous que le cordon
d’alimentation est suffisamment protégé,
notamment au niveau de sa prise électrique
et de l’endroit où il est relié à l’appareil;
cela est également valable pour une
éventuelle rallonge électrique.
11. Utilisez exclusivement des accessoires
et des appareils supplémentaires
recommandés par le fabricant.
12. Utilisez
exclusivement
des chariots,
des diables,
des présentoirs,
des pieds et des
surfaces de travail
recommandés
par le fabricant
ou livrés avec le produit.
Déplacez précautionneusement tout chariot
ou diable chargé pour éviter d’éventuelles
blessures en cas de chute.
13. Débranchez l’appareil de la tension
secteur en cas d’orage ou si l’appareil
reste inutilisé pendant une longue période
de temps.
14. Les travaux d’entretien de l’appareil
doivent être effectués uniquement par
du personnel qualifié. Aucun entretien
n’est nécessaire sauf si l’appareil est
endommagé de quelque façon que ce soit
(dommages sur le cordon d’alimentation
ou la prise par exemple), si un liquide
ou un objet a pénétré à l’intérieur du
châssis, si l’appareil a été exposé à la pluie
ou à l’humidité, s’il ne fonctionne pas
correctement ou à la suite d’une chute.
15. L’appareil doit être connecté à une prise
secteur dotée d’une protection par mise à
la terre.
16. La prise électrique ou la prise IEC de
tout appareil dénué de bouton marche/arrêt
doit rester accessible en permanence.
17. Mise au rebut
appropriée de ce produit:
Ce symbole indique qu’en
accord avec la directive
DEEE (2012/19/EU) et les
lois en vigueur dans votre
pays, ce produit ne doit
pas être jeté avec les
déchets ménagers. Ce produit doit être
déposé dans un point de collecte agréé
pour le recyclage des déchets
d’équipements électriques et électroniques
(EEE). Une mauvaise manipulation de ce
type de déchets pourrait avoir un impact
négatif sur l’environnement et la santé à
cause des substances potentiellement
dangereuses généralement associées à ces
équipements. En même temps, votre
coopération dans la mise au rebut de ce
produit contribuera à l’utilisation efficace
des ressources naturelles. Pour plus
d’informations sur l’endroit où vous pouvez
déposer vos déchets d’équipements pour le
recyclage, veuillez contacter votre mairie ou
votre centre local de collecte des déchets.
DÉNI LÉGAL
MUSIC Group ne peut être tenu pour
responsable pour toute perte pouvant
être subie par toute personne se fiant en
partie ou en totalité à toute description,
photographie ou affirmation contenue
dans ce document. Les caractéristiques,
l’apparence et d’autres informations
peuvent faire l’objet de modifications
sans notification. Toutes les marques
appartiennent à leurs propriétaires
respectifs. MIDAS, KLARK TEKNIK,
LAB.GRUPPEN, LAKE, TANNOY,
TURBOSOUND, TC ELECTRONIC,
TC-HELICON, BEHRINGER, BUGERA,
DDA et TC APPLIED TECHNOLOGIES sont
des marques ou marques déposées de
MUSIC Group IP Ltd. © MUSIC Group IP
Ltd. 2015 Tous droits réservés.
GARANTIE LIMITÉE
Pour connaître les termes et conditions
de garantie applicables, ainsi que
les informations supplémentaires et
détaillées sur la Garantie Limitée de
MUSIC Group, consultez le site Internet
music-group.com/warranty.
Wichtige
Sicherheitshinweise
Vorsicht
Die mit dem Symbol
markierten Anschlüsse führen
so viel Spannung, dass die Gefahr eines
Stromschlags besteht. Verwenden Sie
nur hochwertige, im Handel erhältliche
Lautsprecherkabel mit vorinstallierten
6,3 mm TSSteckern. Alle anderen
Installationen oder Modifikationen sollten
nur von qualifiziertem Fachpersonal
ausgeführt werden.
Achtung
Um eine Gefährdung durch
Stromschlag auszuschließen,
darf die Geräteabdeckung bzw.
Geräterückwand nicht abgenommen
werden. Im Innern des Geräts befinden
sich keine vom Benutzer reparierbaren
Teile. Reparaturarbeiten dürfen nur von
qualifiziertem Personal ausgeführt werden.
Achtung
Um eine Gefährdung durch
Feuer bzw. Stromschlag
auszuschließen, darf dieses Gerät weder
Regen oder Feuchtigkeit ausgesetzt
werden noch sollten Spritzwasser oder
tropfende Flüssigkeiten in das Gerät
gelangen können. Stellen Sie keine mit
Flüssigkeit gefüllten Gegenstände, wie z. B.
Vasen, auf das Gerät.
Achtung
Die Service-Hinweise sind nur
durch qualifiziertes Personal
zu befolgen. Um eine Gefährdung durch
Stromschlag zu vermeiden, führen Sie
bitte keinerlei Reparaturen an dem Gerät
durch, die nicht in der Bedienungsanleitung
beschrieben sind. Reparaturen sind nur von
qualifiziertem Fachpersonal durchzuführen.
1.
Lesen Sie diese Hinweise.
2.
Bewahren Sie diese Hinweise auf.
3.
Beachten Sie alle Warnhinweise.
4.
Befolgen Sie alle Bedienungshinweise.
5. Betreiben Sie das Gerät nicht in der
Nähe von Wasser.
6. Reinigen Sie das Gerät mit einem
trockenen Tuch.
7. Blockieren Sie nicht die
Belüftungsschlitze. Beachten Sie beim
Einbau des Gerätes die Herstellerhinweise.
8. Stellen Sie das Gerät nicht in der
Nähe von Wärmequellen auf. Solche
Wärmequellen sind z. B. Heizkörper,
Herde oder andere Wärme erzeugende
Geräte (auch Verstärker).
9. Entfernen Sie in keinem Fall die
Sicherheitsvorrichtung von Zweipol- oder
geerdeten Steckern. Ein Zweipolstecker
hat zwei unterschiedlich breite
Steckkontakte. Ein geerdeter Stecker hat
zwei Steckkontakte und einen dritten
Erdungskontakt. Der breitere Steckkontakt
oder der zusätzliche Erdungskontakt dient
Ihrer Sicherheit. Falls das mitgelieferte
Steckerformat nicht zu Ihrer Steckdose
passt, wenden Sie sich bitte an
einen Elektriker, damit die Steckdose
entsprechend ausgetauscht wird.
10. Verlegen Sie das Netzkabel so, dass es
vor Tritten und scharfen Kanten geschützt
ist und nicht beschädigt werden kann.
Achten Sie bitte insbesondere im Bereich
der Stecker, Verlängerungskabel und an
der Stelle, an der das Netzkabel das Gerät
verlässt, auf ausreichenden Schutz.
11. Das Gerät muss jederzeit mit
intaktem Schutzleiter an das Stromnetz
angeschlossen sein.
12. Sollte der Hauptnetzstecker oder eine
Gerätesteckdose die Funktionseinheit
zum Abschalten sein, muss diese immer
zugänglich sein.
13. Verwenden Sie nur Zusatzgeräte/
Zubehörteile, die laut Hersteller
geeignet sind.
14. Verwenden
Sie nur Wagen,
Standvorrichtungen,
Stative, Halter
oder Tische, die
vom Hersteller
benannt oder im
Lieferumfang des
Geräts enthalten
sind. Falls Sie einen Wagen benutzen,
seien Sie vorsichtig beim Bewegen der
Wagen-Gerätkombination, um Verletzungen
durch Stolpern zu vermeiden.
15. Ziehen Sie den Netzstecker bei Gewitter
oder wenn Sie das Gerät längere Zeit
nicht benutzen.
16. Lassen Sie alle Wartungsarbeiten
nur von qualifiziertem Service-Personal
ausführen. Eine Wartung ist notwendig,
wenn das Gerät in irgendeiner Weise
beschädigt wurde (z. B. Beschädigung des
Netzkabels oder Steckers), Gegenstände
oder Flüssigkeit in das Geräteinnere gelangt
sind, das Gerät Regen oder Feuchtigkeit
ausgesetzt wurde, das Gerät nicht
ordnungsgemäß funktioniert oder auf den
Boden gefallen ist.
17. Korrekte Entsorgung
dieses Produkts: Dieses
Symbol weist darauf hin,
das Produkt entsprechend
der WEEE Direktive
(2012/19/EU) und der
jeweiligen nationalen
Gesetze nicht zusammen
mit Ihren Haushaltsabfällen zu entsorgen.
Dieses Produkt sollte bei einer autorisierten
Sammelstelle für Recycling elektrischer und
elektronischer Geräte (EEE) abgegeben
werden. Wegen bedenklicher Substanzen,
5
die generell mit elektrischen und
elektronischen Geräten in Verbindung
stehen, könnte eine unsachgemäße
Behandlung dieser Abfallart eine negative
Auswirkung auf Umwelt und Gesundheit
haben. Gleichzeitig gewährleistet Ihr Beitrag
zur richtigen Entsorgung dieses Produkts
die effektive Nutzung natürlicher
Ressourcen. Für weitere Informationen zur
Entsorgung Ihrer Geräte bei einer
Recycling-Stelle nehmen Sie bitte Kontakt
zum zuständigen städtischen Büro,
Entsorgungsamt oder zu Ihrem
Haushaltsabfallentsorger auf.
HAFTUNGSAUSSCHLUSS
MUSIC Group übernimmt keine Haftung
für Verluste, die Personen entstanden
sind, die sich ganz oder teilweise
auf hier enthaltene Beschreibungen,
Fotos oder Aussagen verlassen haben.
Technische Daten, Erscheinungsbild
und andere Informationen können
ohne vorherige Ankündigung geändert
werden. Alle Warenzeichen sind
Eigentum der jeweiligen Inhaber. MIDAS,
KLARK TEKNIK, LAB.GRUPPEN, LAKE,
TANNOY, TURBOSOUND, TC ELECTRONIC,
TC-HELICON, BEHRINGER,
BUGERA, DDA und TC APPLIED
TECHNOLOGIES sind Warenzeichen
oder eingetragene Warenzeichen der
MUSIC Group IP Ltd. © MUSIC Group IP
Ltd. 2015 Alle Rechte vorbehalten.
BESCHRÄNKTE GARANTIE
Die geltenden Garantiebedingungen
und zusätzliche Informationen bezüglich
der von MUSIC Group gewährten
beschränkten Garantie finden Sie online
unter music-group.com/warranty.
6
TCX series
Instruções de
Segurança Importantes
Aviso!
Terminais marcados com o
símbolo carregam corrente
elétrica de magnitude suficiente para
constituir um risco de choque elétrico.
Use apenas cabos de alto-falantes
comercialmente disponíveis de alta
qualidade com plugues TS de ¼"
pré-instalados. Todas as outras instalações
e modificações devem ser efetuadas por
pessoas qualificadas.
Este símbolo, onde quer que o
encontre, alerta-o para a leitura
das instruções de manuseamento
que acompanham o equipamento. Por favor
leia o manual de instruções.
Atenção
De forma a diminuir o
risco de choque eléctrico,
não remover a cobertura (ou a secção de
trás). Não existem peças substituíveis por
parte do utilizador no seu interior. Para esse
efeito recorrer a um técnico qualificado.
Atenção
Para reduzir o risco de
incêndios ou choques eléctricos
o aparelho não deve ser exposto à chuva
nem à humidade. Além disso, não deve
ser sujeito a salpicos, nem devem ser
colocados em cima do aparelho objectos
contendo líquidos, tais como jarras.
Atenção
Estas instruções de operação
devem ser utilizadas,
em exclusivo, por técnicos de assistência
qualificados. Para evitar choques eléctricos
não proceda a reparações ou intervenções,
que não as indicadas nas instruções de
operação, salvo se possuir as qualifi-cações
necessárias. Para evitar choques eléctricos
não proceda a reparações ou intervenções,
que não as indicadas nas instruções de
operação. Só o deverá fazer se possuir as
qualificações necessárias.
1.
Leia estas instruções.
2.
Guarde estas instruções.
3.
Preste atenção a todos os avisos.
4.
Siga todas as instruções.
5. Não utilize este dispositivo perto
de água.
6.
Limpe apenas com um pano seco.
7. Não obstrua as entradas de ventilação.
Instale de acordo com as instruções
do fabricante.
Quick Start Guide
8. Não instale perto de quaisquer
fontes de calor tais como radiadores,
bocas de ar quente, fogões de sala ou
outros aparelhos (incluindo amplificadores)
que produzam calor.
9. Não anule o objectivo de segurança
das fichas polarizadas ou do tipo de
ligação à terra. Uma ficha polarizada
dispõe de duas palhetas sendo uma mais
larga do que a outra. Uma ficha do tipo
ligação à terra dispõe de duas palhetas
e um terceiro dente de ligação à terra.
A palheta larga ou o terceiro dente são
fornecidos para sua segurança. Se a ficha
fornecida não encaixar na sua tomada,
consulte um electricista para a substituição
da tomada obsoleta.
10. Proteja o cabo de alimentação de
pisadelas ou apertos, especialmente
nas fichas, extensões, e no local de
saída da unidade. Certifique-se de
que o cabo eléctrico está protegido.
Verifique particularmente nas fichas,
nos receptáculos e no ponto em que o cabo
sai do aparelho.
11. O aparelho tem de estar sempre
conectado à rede eléctrica com o condutor
de protecção intacto.
12. Se utilizar uma ficha de rede principal
ou uma tomada de aparelhos para desligar
a unidade de funcionamento, esta deve
estar sempre acessível.
13. Utilize apenas ligações/acessórios
especificados pelo fabricante.
14. Utilize apenas
com o carrinho,
estrutura, tripé,
suporte, ou mesa
especificados
pelo fabricante
ou vendidos com
o dispositivo.
Quando utilizar
um carrinho, tenha cuidado ao mover o
conjunto carrinho/dispositivo para evitar
danos provocados pela terpidação.
15. Desligue este dispositivo durante as
trovoadas ou quando não for utilizado
durante longos períodos de tempo.
16. Qualquer tipo de reparação deve ser
sempre efectuado por pessoal qualificado.
É necessária uma reparação sempre que
a unidade tiver sido de alguma forma
danificada, como por exemplo: no caso
do cabo de alimentação ou ficha se
encontrarem danificados; na eventualidade
de líquido ter sido derramado ou objectos
terem caído para dentro do dispositivo;
no caso da unidade ter estado exposta à
chuva ou à humidade; se esta não funcionar
normalmente, ou se tiver caído.
17. Correcta eliminação
deste produto: este
símbolo indica que o
produto não deve ser
eliminado juntamente
com os resíduos
domésticos, segundo
a Directiva REEE
(2012/19/EU) e a legislação nacional.
Este produto deverá ser levado para
um centro de recolha licenciado para a
reciclagem de resíduos de equipamentos
eléctricos e electrónicos (EEE). O tratamento
incorrecto deste tipo de resíduos pode ter
um eventual impacto negativo no ambiente
e na saúde humana devido a substâncias
potencialmente perigosas que estão
geralmente associadas aos EEE. Ao mesmo
tempo, a sua colaboração para a eliminação
correcta deste produto irá contribuir para
a utilização eficiente dos recursos naturais.
Para mais informação acerca dos locais
onde poderá deixar o seu equipamento
usado para reciclagem, é favor contactar
os serviços municipais locais, a entidade
de gestão de resíduos ou os serviços de
recolha de resíduos domésticos.
LEGAL RENUNCIANTE
O MUSIC Group não se responsabiliza por
perda alguma que possa ser sofrida por
qualquer pessoa que dependa, seja de
maneira completa ou parcial, de qualquer
descrição, fotografia, ou declaração aqui
contidas. Dados técnicos, aparências
e outras informações estão sujeitas
a modificações sem aviso prévio.
Todas as marcas são propriedade de seus
respectivos donos. MIDAS, KLARK TEKNIK,
LAB.GRUPPEN, LAKE, TANNOY,
TURBOSOUND, TC ELECTRONIC,
TC-HELICON, BEHRINGER, BUGERA, DDA
e TC APPLIED TECHNOLOGIES são marcas
ou marcas registradas do MUSIC Group IP
Ltd. © MUSIC Group IP Ltd. 2015 Todos
direitos reservados.
安全にお使いいただくために
注意
感電の.恐れがありますので、
カバーやその他の部品を取り
外したり、開けたりしないでください。高
品質なプロ用スピーカーケーブル（¼" TS
標準ケーブルおよびツイスト ロッキング
プラグケーブル）を使用してください。
注意
火事および感電の危険を防ぐ
ため、本装置を水分や湿気の
あるところには設置しないで下さい。装置
には決して水分がかからないように注意
し、花瓶など水分を含んだものは、装置の
上には置かないようにしてください。
注意
このマークが表示されている
箇所には、内部に高圧電流が
生じています。手を触れると感電の恐れが
あります。
注意
取り扱いとお手入れの方法に
ついての重要な説明が付属の
取扱説明書に記載されています。ご使用の
前に良くお読みください。
注意
GARANTIA LIMITADA
Para obter os termos de garantia
aplicáveis e condições e informações
adicionais a respeito da garantia
limitada do MUSIC Group, favor verificar
detalhes na íntegra através do website
music-group.com/warranty.
1. 取扱説明書を通してご覧ください。
2. 取扱説明書を大切に保管してくだ
さい。
3. 警告に従ってください。
4. 指示に従ってください。
5. 本機を水の近くで使用しないでくだ
さい。
6. お手入れの際は常に乾燥した布巾を使
ってください。
7. 本機は、取扱説明書の指示に従い、
適切な換気を妨げない場所に設置してく
ださい。取扱説明書に従って設置してくだ
さい。
8. 本機は、電気ヒーターや温風機器、
ストーブ、調理台やアンプといった熱源か
ら離して設置してください。
9. ニ極式プラグおよびアースタイプ
(三芯) プラグの安全ピンは取り外さないで
ください。ニ極式プラグにはピンが二本つ
いており、そのうち一本はもう一方よりも幅
が広くなっています。アースタイプの三芯プ
ラグにはニ本のピンに加えてアース用のピ
ンが一本ついています。これらの幅の広い
ピン、およびアースピンは、安全のためのも
のです。備え付けのプラグが、お使いのコン
セントの形状と異なる場合は、電器技師に
相談してコンセントの交換をして下さい。
10. 電源コードを踏みつけたり、挟んだり
しないようご注意ください。電源コードや
プラグ、コンセント及び製品との接続には
十分にご注意ください。
11. すべての装置の接地 (アース) が確保
されていることを確認して下さい。
12. 電源タップや
電源プラグは電
源遮断機として利
用されている場合
には、これが直ぐ
に操作できるよう
手元に設置して下
さい。
13. 付属品は本機
製造元が指定したもののみをお使いくだ
さい。
14. カートスタンド、三脚、ブラケット、
テーブルなどは、本機製造元が指定したも
の、もしくは本機の付属品となるもののみ
をお使いください。カートを使用しての運
搬の際は、器具の落下による怪我に十分ご
注意ください。
15. 雷雨の場合、もしくは長期間ご使用に
ならない場合は、電源プラグをコンセント
から抜いてください。
16. 故障の際は当社指定のサービス技術
者にお問い合わせください。電源コードも
しくはプラグの損傷、液体の装置内への浸
入、装置の上に物が落下した場合、雨や湿
気に装置が晒されてしまった場合、正常に
作動しない場合、もしくは装置を地面に落
下させてしまった場合など、いかなる形で
あれ装置に損傷が加わった場合は、装置
の修理・点検を受けてください。
17. 本製品に電源コード
が付属されている場合、
付属の電源コードは本製
品以外ではご使用いただ
けません。電源コードは
必ず本製品に付属された
電源コードのみご使用く
ださい。
7
法的放棄
ここに含まれる記述、写真、意見の全体
または一部に依拠して、いかなる人が損害
を生じさせた場合にも、MUSIC Group
は一切の賠償責任を負いません。
技術仕様、外観およびその他の情報は
予告なく変更になる場合があります。
商標はすべて、それぞれの所有者に帰
属します。MIDAS、KLARK TEKNIK、
LAB.GRUPPEN、 LAKE、TANNOY、
TURBOSOUND、 TC ELECTRONIC、
TC-HELICON、 BEHRINGER、
BUGERA、DDA および
TC APPLIED TECHNOLOGIES は
MUSIC Group IP Ltd. の商標または登
録商標です。© MUSIC Group IP Ltd.
2015 無断転用禁止。
限定保証
適用される保証条件と MUSIC Group
の限定保証に関する概要については、
オンライン上 music-group.com/warranty
にて詳細をご確認ください。
8
TCX series
᧙᜷ᄋ߸Мᮍᅽ
ࣝధ൦ಗ঄ᄋጽቬ᝻‫ܭ‬Чధृ
ܹᄋႄุߜ‫ڛ‬ᝐႄԁᬘǎ̪ᬎ
Ώၺࣝధ ¼" TSੌ੶ᩛऱତ݁
ᄋᰵַ᠐˅ˋੵ‫ܧ‬٩ጴǎ੟ధᄋ߸ᜊੌួ
஠‫ڪ‬ᮍႁՍಬᄋ˅ˋ̢ցᤊᛢǎ
൦ಗ঄ଣᧉ১ַ̘аߜ‫ڛ‬ఴ
ፑᎇᄋԁᬘႄԎధᝐႄԁᬘǎ
൦ಗ঄ଣᧉ১ಋ᫟੟ᬅᄋ᧙᜷
ᄋΏၺԤ፦οឮ௛ǎឱ᫟឵ధ
У੥гǎ
࠶ॸ
˟ᥙГᝐႄԁᬘឱӉ੫ऩ఼
ᮈᄧੌᑁ᭨૖ౝ
ǎ᝻‫ܭ‬а෦
ధԼΚၺਜ਼፦οΏၺᄋᦋ͉ǎឱ࠳፦ο̄
ᮋ̕ႁՍಬᄋ˅ˋ̢ցᤊᛢǎ
࠶ॸ
˟ᥙГᅍ༣ੌᝐႄԁᬘឱӉ
࠳൦᝻‫ܭ‬Ꮇ̇ᭂ๹ੌ໾ິ˘ǎ
൦᝻‫˸ܭ‬ˁԼԫ๰͵໠ຶᄪధ๰͵ᄋࠕ
٩˸ˁԼᎷ̇Цʾ‫ݡ‬ᔊၬ኏ǎ
࠶ॸ
፦οឮ௛̪௨ፍՍಬᄋ˅ˋ፦
ο̢ցΏၺᄋǎ˟ᥙГᝐႄԁ
ᬘᬕ́Ώၺឮ௛˻ଣ҃ᄋ̀ܲឱӉᤊᛢ
͋ͶЦ߳፦οǎ੟ధ፦ο‫ڪ‬ᮍႁՍಬᄋ˅
ˋ̢ցᤊᛢǎ
1. ឱ᫟឵ᤉ̐ឮ௛ǎ
2. ឱ‫ؔݱ‬εߜᤉ̐ឮ௛ǎ
3. ឱญਔ੟ధᄋ᝞ᇩǎ
4. ឱᥗ߷੟ధᄋឮ௛ǎ
5. ឱӉ‫ڛ‬᭦ᤄබᄋ‫ڢ‬ஶΏၺశַ̘ǎ
6. ឱၺࣱ࣌ຎพశַ̘ǎ
7. ឱӉ‫܌܅‬ᤱ᮴Աǎ߸ᜊశַ̘௒ឱᥗ
ཱིԉࠓᄋឮ௛ǎ
8. ឱӉ࠳శַ̘߸ᜊ‫ڛ‬མ຺ᬅᤄ
‫ݡ‬఍ජྠ༰ߖੌЦ̘߳ၸམ᧛ᄋ᝻‫ܭ‬
Ӌ઻ҫ஋٩
ǎ
9. ឱӉሩᬕ౞মତ݁ੌ଍‫ڢ‬ତ݁ᄋ߸М
ᜊᎷǎ଍‫ڢ‬ତ݁௨ႁˑ˕ତ‫܌‬଍གྷԤʸ˕
଍‫݁ڢ‬౟ੈǎᔫᬥ᠏ଣΚᄋତ݁ˁᤡՍ১
ᄋତऑឱ੾ႄࢻట૲ʸ˕Սᤡᄋତऑǎ
10. ‫ؔݱ‬εઑႄ຺ጴΏЦˁᜃ᡼ᢇੌ҉
ᆢࡀЦญਔႄ຺ତ݁Ǎܴၺ᤮ତऑԤ᝻‫ܭ‬
ᤍ଍‫ܬ‬ǎ
Quick Start Guide
11. ឱԷΏၺԉࠓ૊ࠁᄋᬅ࡜᝻‫͉ᦢ֘ܭ‬ǎ
12. ឱԷΏၺԉࠓ
૊ࠁᄋੌᬥ᠏ᩚ
‫׭‬ᄋ੥ଏᢽ౷ߖ
ʽᝉ౷஄౷֘ಹ
ߖǎᔫΏၺ੥ଏᢽ
౐ୄᤃ᝻‫ܭ‬ឱญ
ਔ߸М஋Ꮇ᝻‫ܭ‬
̀ᥙГ੥ଏᢽ֘᝻
‫ܭ‬ϛωᏬԫ͟ǎ
13. ᥆᫆ႄᭈᲟੌ᫃ఱˁΏၺశ᝻‫ܭ‬௒
ឱફѤႄ຺ତ݁ǎ
14. ੟ధ፦ο‫ڪ‬ᮍႁՍಬᄋ፦ο̢ցᤊ
ᛢǎ᝻‫ܭ‬ԫ૰௒ᭋᤊᛢ፦οΔ‫ݡ‬ႄ຺ጴੌ
ႄ຺ତ݁ԫ૰๰͵ุЛੌफྮᗁЛ᝻‫ܭ‬
а᝻‫ܭ‬ᥔᭂ๹ੌԫ໾᝻‫ܭ‬ˁᑠ൥ࣣᤃͼ
ੌᜃ୒‫گ‬ǎ
15. శ᝻‫ܭ‬ᤍ଍ႄ຺௒ʸࠁ᜷ధ଍‫ڢ‬
εઑǎ
16. ᔫႄ຺ତ݁ੌ٩Ч
ᏺՍ٩ၺͼளႄᜊᎷ
अैε᝾߳̈́‫̇ܬ‬ᬥ௒Լ
ஶΨ୳ͼ࿅ঘǎ
17. శַ̘̪ᤡၺ̇๓ફ
2000ዜ̀ʿ‫ڢ‬Ӟశַ̘
̪ᤡၺ̇᭥མࣝජό౏
͉ʿǎ
ฃ०‫ܧ‬௛
ࠬ̇͋Ͷ‫ڛڃ‬൦ឮ௛˻ଣ҃ᄋМᦋੌ
ᦋ͌ଢᤙǍ‫ܧੌྠڐ‬௛Ꮼᤶੈᄋ૰݀
MUSIC Groupˁ᠈͋Ͷ᠋͋ǎ઀సԡஞ
֘ܲ᜻ᔫధటஉিˁԴᛢᤱᅽǎ੟ధᄋ
‫׹‬ಗ‫˟ڪ‬ЦՋᒮ੟ధᏩᄋ᠊̘ǎMIDAS,
KLARK TEKNIK, LAB.GRUPPEN,
LAKE, TANNOY, TURBOSOUND,
TC ELECTRONIC, TC-HELICON,
BEHRINGER, BUGERA, DDA
֘TC APPLIED TECHNOLOGIES௨
MUSIC Group IP Ltd.ОՄᄋ‫׹‬ಗੌ
ญг‫׹‬ಗǎ© MUSIC Group IP Ltd.
2015ྡీ੟ధǎ
9
Getting Started
Models covered by this Quick Start Guide
TCX82 / TCX82-WH, TCX102 / TCX102-WH, TCX122 / TCX122-WH, TCX152 / TCX152-WH,
TCX115B / TCX115B-WH, TCX118B / TCX118B-WH
Thank you for choosing a TURBOSOUND loudspeaker product for your application. If you would like further
information about this or any other product, please visit our website turbosound.com.
System Requirements
εο౏൝
TCX series two-way loudspeakers operate as passive systems and
ధУᮄˮᬸ‫څ‬εοᄋᤡၺ౏
൝ԤЦ߳ᄲУθ্ឱᄇᬇ
music-group.com/warranty
Ꭻቤಋᄻߺ஠ᄋឡጻθ্ǎ
require only one amplifier channel for correct operation; the internal
2+
2+
1-
1-
Speakon NL4
2-
passive crossover network built into each enclosure splits the
2-
1+
frequency range appropriately between the LF driver and the HF driver.
1+
Negative (-ve)
Positive (+ve)
TCX loudspeakers are equipped with two Speakon NL4 connectors
wired in parallel with a 4-way barrier strip connector, providing input
and loop-through connections to additional TCX series loudspeakers.
+
To avoid wasting amplifier power you should use heavy-duty speaker
–
+
Loop in
cable with a minimum wire size of 12 gauge (1.5mm²), and preferably
–
Loop out
4-way barrier strip
10 gauge (2.5mm²) for longer runs. For extreme cable lengths be
aware of cable impedance and resistive losses. Always observe the correct polarity as shown.
Amplifier Considerations
TCX series loudspeaker enclosures should be driven by high quality power amplifiers designed for true
professional use. Power amplifiers should be capable of delivering long term broadband power equal
to the loudspeaker’s program power rating at its stated nominal impedance. The use of under-powered
amplifiers must be avoided as heavily clipped signals can cause permanent loudspeaker damage.
Model
Impedance
Amplifier power (cont)
TCX82/-WH
TCX102/-WH
TCX122/-WH
TCX152/-WH
TCX115B/-WH
TCX118B/-WH
8Ω
8Ω
8Ω
8Ω
8Ω
8Ω
400 W
500 W
600 W
700 W
2000 W
2000 W
System Controllers
TCX systems can be used with TURBOSOUND LMS-D24 or LMS-D26 controllers to provide improved
performance as well as vital operating and system security features. If you do not have a controller,
please contact your TURBOSOUND dealer for further details. TURBOSOUND LMS-D2X controllers provide
preset slots into which you can load TCX loudspeaker model parameters, available as a free download.
To use your TCX loudspeaker with a TURBOSOUND controller:
1. Download and install the TCX loudspeaker presets from the TURBOSOUND website turbosound.com.
2. Power up the controller(s) and associated power amplifiers.
3. Press RECALL to select the appropriate program from the preset menu using the ‘A’ ROTARY ENCODER.
4. Press RECALL again to accept the preset. The controller will un-mute and is then ready for use.
10
TCX series
Quick Start Guide
Networking Capability with LMS series Controllers
• LMS-D2X controllers are designed to offer control and monitoring of system parameters over a BvNet
network in real time using a PC and TurboDrive software. The controllers are equipped with network
cards to allow the building of comprehensive networked loudspeaker systems.
• Download the TurboDrive software from the supplied CD or from the TURBOSOUND website
11
Use with Speaker Poles and Speaker Stands
Use an industry standard speaker pole on top of a bass cabinet to raise the
mid/high cabinets to above head height for better audience coverage. For
portable use remove the plastic bung covering the pole mount socket. Fit
the speaker pole into the pole mount socket on the TCX bass cabinet and
mount the TCX two-way cabinet to the top of the pole. Always use caution
turbosound.com and follow the installation instructions.
• Install the drivers. If connecting via RS232 there is no need to install drivers. If connecting via USB
when lifting the loudspeaker.
install the USB drivers which can be found on the CD that came with your Linea Research USB interface.
• Networking multiple devices to a PC: BvNet is the method of connecting multiple devices and this is
done with the Linea Research USB & RS232 Interface (available from TURBOSOUND). The interface
Wall Brackets
1. Separate the component parts of the bracket into the wall plate and
enables devices to be connected to a PC either using RS232 or using USB. EIA485 is the network
speaker plate assemblies by removing the nylock nut underneath the
protocol among the networked devices and is carried over CAT5-type cables. It works with the
wall plate horizontal lug.
following: PC with Windows NT, Windows 2000, Windows XP, or Windows Vista operating systems,
or with Pentium processor, or CD ROM drive or internet access, RS232 or USB port.*
• RS232: Connect your computer to the BvNet interface using a standard 9-pin serial cable. External power
is required for RS232 operation and this should be provided by the Linea Research Accessory Power Supply.
• USB: Connect your computer to the BvNet interface using a USB Type A to USB Type B cable.
2. Remove the countersunk bolts on the rear panel of the cabinet and
attach the speaker plate to the cabinet with the bolts supplied.
3. Fix the wall plate in the venue using appropriate fixings
(not supplied), ensuring that the cable access hole is towards the top.
4. Lift the loudspeaker on to the wall plate and locate the large
captive bolt welded to the speaker plate through the wall plate lug.
External power is not required when using USB.
• Connect networked devices via RJ45 CAT5 cables.
Re-assemble the bracket parts, adjust the aim of the loudspeaker and
• Launch the TurboDrive software.
tighten all bolts.
Illustrated: TCX152 on a WB-55 wall bracket
• Application Authorisation: TurboDrive prompts for an Authorisation Code on the first launch which
Ceiling Brackets
is PJLUWZ.
1. Separate the component parts of the bracket into the ceiling plate and
• Select the COM port from Network > Com Port.
• Click the Online toolbar button.
speaker plate assemblies by removing the nylock nut underneath the
• Click on one of the devices that appear in the tree view to Launch the panel.
wall plate lug.
• When the progress bar indicates ready, adjust the controls as required.
• Please refer to the TurboDrive User Guide for further information on networking.
2. Remove the countersunk bolts on the rear panel of the cabinet and
attach the speaker plate to the cabinet with the bolts supplied.
3. Fix the ceiling plate in the venue using appropriate fixings
Mounting and Fixing
(not supplied). Lift the loudspeaker on to the ceiling plate and
TCX series cabinets are designed with multiple internal rigging points to suit many possible mounting
re-assemble the bracket fixings, adjust the aim of the loudspeaker
methods in permanent installations and portable situations. The table below summarises the mounting
and tighten all bolts.
accessories available for each model.
Model
Illustrated: TCX122 on a CB-55 wall bracket
Pole Brackets
Wall mount
Ceiling mount
Eyebolts
Pole bracket
TCX82/-WH
WB-20
CB-20
EB-10-40
PB-55
TCX series mid-high cabinets equipped with a recessed pole mount socket can be wall mounted with the
TCX102/-WH
WB-20
CB-20
EB-10-40
PB-55
generic TPOLE-BK pole bracket. Fix the bracket in the venue using appropriate wall fixings, mount the
TCX122/-WH
WB-20
CB-20
EB-10-40
PB-55
loudspeaker on to the spigot, and aim the loudspeaker as required. Tighten the pole bracket grub screw to
TCX152/-WH
WB-20
CB-20
EB-10-40
PB-55
lock the loudspeaker and prevent unauthorised removal.
TCX115B/-WH
N/A
N/A
EB-10-40
N/A
TCX118B/-WH
N/A
N/A
EB-10-40
N/A
*Windows NT, Windows 2000, Windows XP and Windows Vista are either registered trademarks or trademarks of
Microsoft Corporation in the United States and/or other countries. Pentium is a trademark of Intel Corporation in the
U.S. and/or other countries.
12
TCX series
OmniMount Brackets
The internal rigging points are also compatible with OmniMount series 120 wall and ceiling brackets.
Quick Start Guide
Servicing and Driver Removal
1. Place the cabinet on its back on a suitable work surface. Remove the eight Pozidrive countersunk screws
To mount TCX cabinets with OmniMount brackets follow the instructions provided with the brackets.
that hold the grille in place and set the grille aside (fig 1).
2. Remove the M5 hex head bass driver fixings screws (fig 2).
Suspending with Eyebolts
3. Disconnect and remove the bass driver, making a note of the polarity for later reconnection (fig 3).
TCX cabinets can be suspended using optional eyebolts coupled to the internal
4. Remove the M5 hex head HF horn fixing screws (fig 4).
rigging points provided on the top, bottom and sides and back. The simplest
method is to use the two rigging points on the top and a single pull-back rigging
point in the centre of the rear panel.
Remove the appropriate countersunk screws and replace them with shoulder
eyebolts, which must have a thread length of at least 18 mm. Use the rear rigging
point to angle the cabinet for optimum room coverage. Cabinets may be hung
upside down if required.
fig 1
fig 2
fig 3
5. Lift out the horn and compression driver assembly. Disconnect the cables from the compression driver,
IMPORTANT NOTE: The mounting of a permanently installed sound system may be dangerous unless
undertaken by qualified personnel with the required experience and certification to perform the necessary
making a note of the polarity for later reconnection (fig 5).
6. Reinstatement is a simple reversal of the above process. Reconnect the compression driver cables,
tasks. Walls, floors or ceilings must be capable of safely and securely supporting the actual load.
The mounting accessory used must be safely and securely fixed both to the loudspeaker and to the wall,
floor or ceiling.
observing the correct polarity (white cable to the +ve terminal, green/white cable to the –ve terminal).
7. Replace the horn and driver in the cabinet.
8. Replace the horn fixing screws and tighten.
When mounting rigging components on walls, floors or ceilings, ensure that all fixings and fasteners used
are of an appropriate size and load rating. Wall and ceiling claddings, and the construction and composition
of walls and ceilings, all need to be taken into account when determining whether a particular fixing
arrangement can be safely employed for a particular load. Cavity plugs or other specialist fixings, if required,
must be of an appropriate type, and must be fitted and used in accordance with the maker’s instructions.
The operation of your speaker cabinet as part of a flown system, if installed incorrectly and improperly,
can potentially expose persons to serious health risks and even death. In addition, please ensure that
electrical, mechanical and acoustic considerations are discussed with qualified and certified (by local state
fig 4
fig 5
or national authorities) personnel prior to any installation or flying.
Make sure that speaker cabinets are set up and “flown” by qualified and certified personnel only,
using dedicated equipment and original parts and components delivered with the unit. If any parts or
components are missing please contact your Dealer before attempting to set up the system.
9. Reconnect the bass driver cables, observing the correct polarity (brown cable to the red +ve terminal,
blue cable to the black –ve terminal) and reinstate the driver in the cabinet. Replace and tighten the driver
fixing screws.
10. Replace the grille and phase check the cabinet before use.
Be sure to observe the local, state and other safety regulations applicable in your country. MUSIC Group,
including the MUSIC Group companies listed on the enclosed “Service Information Sheet”, assume no liability
for any damage or personal injury resulting from improper use, installation or operation of the product.
Regular checks must be conducted by qualified personnel to ensure that the system remains in a secure and
stable condition. Make sure that, where the speaker is flown, the area underneath the speaker is free of human
traffic. Do not fly the speaker in areas which can be entered or used by members of the public.
Speakers create a magnetic field, even if not in operation. Therefore, please keep all materials which can
be affected by such fields (discs, computers, monitors etc) at a safe distance. A safe distance is usually
between 1 and 2 metres.
13
14
TCX series
Rotating the HF Horn Pattern
Quick Start Guide
15
Technical Specifications
The high frequency horn in all TCX two-way models can
TCX152 (WH)
be rotated through 90° in order to swap the horizontal
TCX118B (WH)
TCX115B (WH)
System
and vertical dispersion patterns, particularly useful to
Frequency response
85 Hz - 18 kHz ±3 dB
55 Hz - 20 kHz -10 dB
Nominal dispersion
90° H x 60° V @ -6 dB points
Half space
Half space
Power handling (IEC)
350 W continuous, 1400 W peak
1,000 W continuous,
4,000 W peak
1,000 W continuous,
4000 W peak
Sensitivity
99 dB (1 W @ 1 m)
97 dB (1 W @ 1 m)
95 dB (1 W @ 1 m)
Maximum SPL
125 dB continuous, 131 dB peak
127 dB continuous, 133 dB peak
125 dB continuous, 131 dB peak
Impedance
8Ω
8Ω
8Ω
necessary to achieve the desired coverage pattern and
Components
1 x 15" (381 mm) LF driver
1 x 1" (25 mm)
HF compression driver
1 x 18" (457 mm) LF driver
1 x 15" (380 mm) LF driver
replace it in the cabinet.
Enclosure
2 x Neutrik speakON NL4,
1 x barrier strip terminals
2 x Neutrik speakON NL4,
1 x barrier strip terminals
retain the wide horizontal dispersion when the cabinet is
installed horizontally in venues with limited ceiling height.
1. Remove the loudspeaker grille as before.
2. Remove the M5 hex head HF horn fixing screws.
3. Lift the horn / driver assembly out, rotate the horn as
35 Hz - 125 Hz ±3 dB
25 Hz - 170 Hz -10 dB
35 Hz - 125 Hz ±3 dB
28 Hz - 170 Hz -10 dB
4. Replace the horn fixing screws and tighten.
Connectors
2 x Neutrik speakON NL4,
1 x barrier strip terminals
5. Replace the grille and phase check the cabinet before use.
Wiring
Pins 1+ / 1- input, pins 2+ / 2- link
Pins 1+ / 1- input, pins 2+ / 2- link
Pins 1+ / 1- input, pins 2+ / 2- link
Dimensions HWD
652 x 466 x 422 mm
(25.6 x 18.3 x 16.7")
660 x 560 x 660 mm
(26.0 x 22.0 x 26.0")
600 x 499 x 600 mm
(23.6 x 19.7 x 23.6")
Net weight
23.5 kg (51.8 lbs)
38.6 kg (85.1 lbs)
34.0 kg (75.0 lbs)
EASE data is available for TCX series loudspeakers to enable software simulation of audio coverage
Construction
15 mm (5/8") birch plywood
15 mm (5/8") birch plywood
15 mm (5/8") birch plywood
installation projects. Please visit turbosound.com for a free EASE data download.
Finish
Semi matt black paint
(white optional)
Semi matt black paint
(white optional)
Semi matt black paint
(white optional)
Grille
Powder coated perforated steel
Powder coated perforated steel
Powder coated perforated steel
Flying hardware
M10 x 9, M8 x 4, M6 x 4 Points
M10 x 8 Points
M10 x 8 Points
EASE Data
TCX122 (WH)
TCX102 (WH)
TCX82 (WH)
System
Frequency response
100 Hz - 18 kHz ±3 dB
68 Hz - 20 kHz -10 dB
100 Hz - 20 kHz ±3 dB
68 Hz - 20 kHz -10 dB
100 Hz - 20 kHz ±3 dB
70 Hz - 20 kHz -10 dB
Nominal dispersion
90° H x 60° V @ -6 dB points
90° H x 60° V @ -6 dB points
90° H x 60° V @ -6 dB points
Power handling (IEC)
300 W continuous, 1,200 W peak
250 W continuous, 1000 W peak
200 W continuous, 800 W peak
Sensitivity
97 dB (1 W @ 1 m)
95 dB (1 W @ 1 m)
94 dB (1 W @ 1 m)
Maximum SPL
122 dB continuous, 128 dB peak
119 dB continuous, 125 dB peak
117 dB continuous, 123 dB peak
Impedance
8Ω
8Ω
8Ω
Components
1 x 12" (305 mm) LF driver
1 x 1" (25 mm)
HF compression driver
1 x 10" (254 mm) LF driver
1 x 1" (25 mm)
HF compression driver
1 x 8" (203 mm) LF driver
1 x 1" (25 mm)
HF compression driver
Connectors
2 x Neutrik speakON NL4,
1 x barrier strip terminals
2 x Neutrik speakON NL4,
1 x barrier strip terminals
2 x Neutrik speakON NL4,
1 x barrier strip terminals
Wiring
Pins 1+ / 1- input, pins 2+ / 2- link
Pins 1+ / 1- input, pins 2+ / 2- link
Pins 1+ / 1- input, pins 2+ / 2- link
Dimensions HWD
552 x 406 x 368 mm
(21.8 x 15.9 x 14.5")
488 x 366 x 332 mm
(19.2 x 14.4 x 13.0")
408 x 308 x 280 mm
(16.0 x 12.1 x 11.0")
Net weight
18.3 kg (40.2 lbs)
15.1 kg (33.3 lbs)
10.3 kg (22.7 lbs)
Construction
15 mm (5/8") birch plywood
15 mm (5/8") birch plywood
12 mm (1/2") birch plywood
Finish
Semi matt black paint
(white optional)
Semi matt black paint
(white optional)
Semi matt black paint
(white optional)
Grille
Powder coated perforated steel
Powder coated perforated steel
Powder coated perforated steel
Flying hardware
M10 x 9, M8 x 4, M6 x 4 Points
M10 x 9, M8 x 4, M6 x 4 Points
M10 x 9, M8 x 4, M6 x 4 Points
Enclosure
16
TCX series
Other important information
Important information
1. Register online. Please register your
new MUSIC Group equipment right after
you purchase it by visiting turbosound. com.
Registering your purchase using our
simple online form helps us to process your
repair claims more quickly and efficiently.
Also, read the terms and conditions of our
warranty, if applicable.
2. Malfunction. Should your MUSIC Group
Authorized Reseller not be located in your
vicinity, you may contact the MUSIC Group
Authorized Fulfiller for your country listed
under “Support” at turbosound. com.
Should your country not be listed, please
check if your problem can be dealt with by
our “Online Support” which may also be
found under “Support” at turbosound. com.
Alternatively, please submit an online warranty
claim at turbosound. com BEFORE returning
the product.
3. Power Connections. Before plugging
the unit into a power socket, please make
sure you are using the correct mains voltage
for your particular model. Faulty fuses must
be replaced with fuses of the same type and
rating without exception.
Quick Start Guide
17