Elikon EVD2-60IN 2 wire intercom system User manual

2 WIRE INTERCOM SYSTEM

EVD2-60IN

Please read this manual carefully before using the product, and keep it well.

ENGLISH

1. Parts and Functions

SD card

Digital TFT LCD Screen

Talk/MON Button

Menu Button

Unlock Button

Microphone

L1

L2

Mounting Hook

Connection Port

Speaker

-1-

Key functions

LCD screen

Unlock button

Display the visitors' image

Press to release the door

Menu button Press to open the menu shortcuts

Talk/Mon button Press to communicate hands free with visitor

Microphone

Mounting hook

Connection port

Speaker

Press to view the outdoor condition in standby mode

Receive voice from the user

Use to hang up the monitor

Bus terminal

Send out vioce from the visitor

DIP Settings

Bit

DIP1&2

Bit State

3

3

DIP3

3

Description

Reserved. left to default.

Set to OFF. When the monitor is in the middle of the line in daisy chain connection.

Set to ON. When the montior is at the end of the line or connected to a DBC4S.

2. Monitor Mounting

1. Use the screws to fix the Mounting Bracket on the mounting box.(fitting accesories includes a Bracket (Two pieces of 4X25 screws are needed to fasten the Mounting

Bracket), Special 2 wire connectors to connect with Monitor)

2. Wire the system correctly(refer to connection chapter) then hang the Monitor on the Mounting Bracket firmly.

3. Main Menu

Touch the touch button anywhere in standby mode, the main menu page will be shown as follows:

4. Basic Door Release Operation

1. Press CALL button on outdoor station, the

Monitor rings, at the same time, the screen displays the visitors' image.

It will display the call source string

00:30 Front Door

2. Press TALK/MON Button on monitor or touch icon on screen, you can communicate hands free with the visitor for

90 seconds.After finishing communication,press TALK/MON button again or touch icon to end the communication. If nobody answers the phone, the screen will be turned off automatically after 30 seconds.

-2-

3.

UNLOCK Button or touch door for the visitor.(if two locks are connected to door camera,touch unlock

2nd icon to release the second lock )

icon to open the

4.

can display the view of outside. Or touch Monitor icon on main menu to get into the door camera switching mode, if multi door stations are installed, you can press the door 1/2/3/4 to monitor the door station or CCTV camera you want.press

icon to exit and enter main menu page.

Note: if the system connect 2 wire camera via camera controller, press the camera

1/2/3/4 to monitor the camera you want.press icon to exit and enter main menu page.

5. Intercom Function

Touch

Intercom icon on main menu to get into the intercom mode , you have 4 item to select:Inner Broadcast, Inner Call, Name List Call and Call Guard Unit.

-3-

1.

Inner Broadcast

: If multi slave monitors are installed in the same apartment, select

Inner Broadcast, all the other monitors will mandatory receive broadcast content at the same time, whichever slave monitor doesn't need to answer the broadcast, and whichever slave monitor also doesn't need to open the scrccn.

2.

Inner Call

: If multi slave monitors are installed in the same apartment, select Inner

Call, all the other Monitors will ring at the same time, whichever Monitor answers the call, conversation is started.and the other monitors will stop ringing at the same time.

3.

Name List Call

: User in one apartment can call other apartments in the system.

Touch Name List Call icon (the namelist will be created automatically by the system) on intercom mode menu page, Select a name on the screen then touch

icon to call.Press / icon to enter last/next name list page. (Touch Dial

Number icon again to redial)

4.

5.

6.

7.

Name List

[ 01 ] Jim. Zhang

[ 02 ] Calo. Liu

[ 03 ] Jacko. Zhang

[ 04 ] Philips. Chen

[ 05 ] Hebe. Zhang

[ 06 ] Tony. Li

8.

4.

Call Guard Unit

: A Monitor can be assigned as Guard Unit Monitor; when the Guard

Unit Monitor answers the call, conversation with the guard person is started..

6. Video/Picture Memory

Note: The video/picture memory function is built into the monitor.

Video/Picture Recording

Both Auto-Recording and Manual-Recording are available.And Auto-Recording is default. If receive a call , after 3s, the monitor will record one video/picture for each calling automatically. Or you can touch icon to record the visitor's video/image manually when the monitor is in monitoring or calling.

Video/Picture Playback

Touch Playback icon on main menu, the recorded videos/pictures will be played on screen, please note that touch icon to Start/Pause the videos recorded.

-4-

-5-

Image:008/020 2014/06/23 14:36:55

Note: When the system without SD card: 1.118 pictures in inner memory

2.Manage each picture.

When the system with SD card:1.A brand new SD card needs to be formated

by the monitor, then can it be used for video recording.

2.Up to 32G Micro SD card.

3.Video & Audio record.

4.Manage each video clips.

5.Can be copied.

7. Call Record Function

Call Record:All the calls concerning the montior, including Door-station-to-monitor call, monitor-to-monitor call, will be recored and can be reviewed afterwards.

Touch Call Record icon on main menu to get into the call record mode.When there are unread call records, arrow color red. Press the unread call record, and then touch icon to play it.

Call Record

01/05

06-23 15:22 Calo.Liu

06-18 20:54 Smith

06-12 11:06 Vincent.Yang

05-29 08:39 Allen.Chen

05-27 21:43 Hebe.Zhang

04-20 13:16 Ben.Wu

Note: 1.Automatic limited number of records.

2.Do not need to delete any a record.

Call Record

01/05

06-23 15:22 Calo.Liu

06-18 20:54 Smith

06-12 11:06 Vincent.Yang

05-29 08:39 Allen.Chen

05-27 21:43 Hebe.Zhang

04-20 13:16 Ben.Wu

8. Do Not Disturb Function

Touch

Do Not Disturb

icon on main menu to get into the don't disturb mode , you have 4 item to select:Normal, For 1 Hour, For 8 Hours and Always. You can select the appropriate item according to your needs.

Do Not Disturb

Normal

For 1 Hour

For 8 Hours

Always

Refuse Call In: 00:58:32

Note: When you select "For 1 Hour" or "For 8 Hours", bottom of the screen will display the remaining time.

9. Divert Function

Touch

Divert

icon on main menu to get into the transfer mode. Touch the empty place ,and then input the telephone number by pressing the digital keypad.And it has 3 types of divert modes:

1:Don't Transfer----calls from outdoor station will not be diverted.

2:If No Answer----outdoor station calls indoor monitor firstly,if nobody answer the call within 30 seconds,the call will be diverted to the telephone number you set. At this mode,the monitor will shut off immediately when TPC/GSM/

TPS divert sucessfully,while it won't affect the communication between TPC/

GSM/TPS and outdoor station.Otherwise, the monitor can do the operation of monitoring,talking,and unlocking.

3:Simutaneously----calls from outdoor station will be diverted to your telephone immediately.At this mode,the monitor won't shut off when TPC/GSM/TPS divert sucessfully,but if the monitor answers the call at this time,TPC/GSM/TPS will quit absolutely.

Transfer Options

Don't Transfer

If No Answer

Simutaneously

1)

2)

3)

-6-

Note:1.Touch icon to detect the transfer device info.

2.Touch icon to send message.

Transfer Options

Don't Transfer

If No Answer

Simutaneously

1)

2)

3)

Transfer Device Info

Device -

SIM -

Network -

Signal Level -

10. Staircase Light

Note: the staircase light function will be activated only when the system connect light via SC6V module, otherwise, this function is unvalid in normal. For more information, please refer to SC6V user instruction in detail.

On main menu page or in monitoring,touch Light icon to open the staircase light, the staircase light will be turned off automatically.

11. Basic Setup Instructions

Sounds Settings

Touch icon on main menu page(or on door camera switching mode page), then select

"Sounds" item to enter the sounds settings page.You can set a variety of ring tones on this page.(touch icon to exit the setting and return main menu page.

-7-

Note: Door Ring have 2 mode:United and Seperate.If select "United",it means

Door1/2/3/4 as a whole to adjust the ring tones.

Date & Time Settings

"

Touch icon on main menu page(or on door camera switching mode page), then select

Date & Time

" item to enter the date & time settings page.You can set the date & time on this page.(touch icon to exit the setting and return main menu page.

Note: You can set your own time, you can also synchronize the system time.

Rename & Monitor Time Settings

"

Touch icon on main menu page(or on door camera switching mode page), then select

More...

" item to enter the Rename & monitor time settings page.You can set door station rename, camera rename, monitor time on this page.(touch icon to exit the setting and return main menu page.

-8-

Note: If you want to rename, please touch the place of name, then it will turn keypad page ,you can input your new name in this page.

DS-3_

DOOR3 RENAME abc

-9-

Screen and Volume Adjustment

During monitoring or talking state, touch icon,the Adjust page will be displayed.

1. The Scene mode selection: Total 4 screen modes can be selected in sequence:

Normal,

Brightly, Soft

Brightness

User

and

User.

Whenever you modify

or

colour, Scene

item will be set to

mode automatically.

2. Note that all the modifications will be performed immediately after the operation.

Touch the window of image to exit the adjust page.

12. Restore to Default

The restore to default function allows the user to recover the settings to factory setting.

Note that the restore to default operation will not change the setting and datas.

Enter main menu page,and touch icon, then select "About" item (or touch logo position) to enter the about settings page, touch icon, the default settings will be loaded. touch icon to enter the Memo Information page, touch and icon to copy the pictures to SD card. Touch and icon to format SD card and restart.

About

Local Address 00.00

Video Standard AUTO

System Verson 00.01.00

Display Driver 1.0

Front 1.0

UI 1.0

Format SD Card And Restart ?

Memo Information

SD Card --

Video Capacity ----

Video Usage ----

Flash

Image Capacity 0118

Image Usage 0000

Copy Pictures To SD ?

Memo Information

SD Card --

Video Capacity

----

Video Usage ----

Flash

Image Capacity 0118

Image Usage 0000

13. Monitor Parameter Setting

How to enter the installation setting page

1.Touch icon on main menu page.

About

Local Address 00.00

Video Standard AUTO

System Verson 00.01.00

Display Driver 1.0

Front 1.0

UI 1.0

2.Touch UNLOCK button and hold for 2s.

_

INSTALLER SETUP

123

3.A digital keypad will be shown.

How to set the monitor as a Guard Monitor

A Monitor can be assigned as Guard Unit Monitor; when the Guard Unit Monitor answers the call, conversation with the guard person is started..

The code number of 8004 is used to set the monitor as a guard unit monitor and 8005 is used to cancel this function.

-10-

How to set the slave monitor address

Maximum 4 monitors can be connected in one apartment,one master monitor together with 3 slave monitors, so you should set the address correctly.(note:must have one monitor to be set as master monitor)

The code of 8000 is used to set the master monitor.

The code of 8001 is used to set the first slave monitor .

The code of 8002 is used to set the second slave monitor .

The code of 8003 is used to set the third slave monitor .

-11-

How to set date and time format

The system offers two methods of date and time.

The code number of 8008 is used to set the date format as month/date/year

The code number of 8009 is used to set the date format as date/month/year

The code number of 8012 is used to set the time format as 12 hour system

The code number of 8013 is used to set the time format as 24 hour system

How to set the monitor panel on

In default mode,when receive a calling,the master and slave monitors will ring at the same time,and just the master monitor can display the image while the slave monitors can not.But the settings can be changed,you can set the master monitor and all the slave monitors to panel on at the same time when receiving a call, just input the code number of 8006 on each slave monitor.







   

How to set the unlock parameter

Unlock mode:

There are two unlock modes: 1.power-on- to-unlock type:unlock mode=0(by default)

2.power-off-to-unlock:unlock mode=1.

The code number of 8010 is used to set the unlock mode to 0

The code number of 8011 is used to set the unlock mode to 1

Unlock time:

The unlock time can be changed by yourself at any time. it can be set from 1 to 99 seconds.

The code number from 8401 to 8499 are used to set the unlock time to 1~ 99 seconds.

How to set the user code for the monitor

Each monitor should be assigned an address in the system, total 32 addresses can be configured, the code number of 8200 to 8231 is used to controlled the address of 00 to

31. Please refer to the following table.

Input No.

8204

8205

8206

8207

8208

8209

8210

8200

8201

8202

8203

User Code

Code=0

Code=1

Code=2

Code=3

Code=4

Code=5

Code=6

Code=7

Code=8

Code=9

Code=10

Input No.

8215

8216

8217

8218

8219

8220

8221

8211

8212

8213

8214

User Code Input No.

User Code

Code=11

Code=12

Code=13

Code=14

Code=15

Code=16

Code=17

Code=18

Code=19

Code=20

Code=21

8222

8223

8224

8225

8226

8227

8228

8229

8230

8231

Code=22

Code=23

Code=24

Code=25

Code=26

Code=27

Code=28

Code=29

Code=30

Code=31

-12-

-13-

14. Specification

●

●

●

●

DC●20~28V●

●

●● Standby●12.4mA;●Working●270mA

7●Inch●digital●color●LCD

800*3(R,●G,●B)●x●480●pixels

1Vp-p,●75Ω,●CCIR●standard

2●wires,●non-polarity

139(H)×212(W)×15(D)mm

15. Precautions

1) All components should be protected from violence vibration. And not allow to be impacted, knocked and dropped.

2) Please do the cleanness with soft cotton cloth, please do not use the organic impregnant or chemical clean agent. If necessary, please use a little pure water or dilute soap water to clean the dust.

3) Image distortion may occur if the video monitor is mounted too close to magnetic field e. g. Microwaves, TV, computer etc.

4) Please keep away the monitor from wet, high temperature, dust, caustic and oxidation gas in order to avoid any unpredictable damage.

5) Must use the right adaptor which is supplied by the manufacturer or approved by the manufacturer.

6) Pay attention to the high voltage inside the products, please refer service only to a trained and qualified professional.

Note

-14-

2 WIRE INTERCOM SYSTEM

EVD2-60IN

The design and specifications can be changed without notice to the user. Right to interpret and copyright of this manual are preserved.