AVerVision F50-8M User Manual

AVerVision F50-8M User Manual
AVerVision F50-8M
User Manual
F e d e r a l C o m m u n i c a t i o n s C o m m i s s i o n S t a t e m e n t ( C l a s s A)
NOTE- This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are de signed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful i nterference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by tuning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
 Consult the dealer or an experienced radio/television technician for help.
Class A ITE:
Class A ITE is a category of all other ITE which satisfies the class A ITE limits but not th e class B
ITE limits. Such equipment should not be restricted in its sale but the following warning shall be
included in the instructions for use:
Warning - This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
CE Class A (EMC)
This product is herewith confirmed to comply with the requirements set out in the
Council Directives on the Approximation of the laws of the Member States relating to
Electromagnetic Compatibility Directive 2014/30/EU.
Warning - This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate measures to
correct this interference.
D I S C L AI M E R
No warranty or representation, either expressed or implied, is made with respect to the contents
of this documentation, its quality, performance, merchantability, or fitness for a particular
purpose. Information presented in this documentation has been care fully checked for reliability;
however, no responsibility is assumed for inaccuracies. The information contained in this
documentation is subject to change without notice.
In no event will AVer be liable for direct, indirect, special, incidental, or consequential damages
arising out of the use or inability to use this product or documentation, even if advised of the
possibility of such damages.
T R AD E M AR K S
“AVer” is a trademark owned by AVer Information Inc. Other trademarks used herein for
description purpose only belong to each of their companies.
COPYRIGHT
© 2016 AVer Information Inc. All rights reserved.
All rights of this object belong to AVer Information Inc. Reproduced or transmitted in any form
or by any means without the prior written permission of AVer Information Inc. is prohibited. All
information or specifications are subject to change without prior notice.
NOTICE
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. THE
INFORMATION CONTAINED HEREIN IS TO BE CONSIDERED FOR REFERENCE ONLY.
WARNING
TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE. WARRANTY VOID FOR ANY
UNAUTHORIZED PRODUCT MODIFICATION.
THE MARK OF CROSSED-OUT WHEELED BIN INDICATES THAT THIS
PRODUCT MUST NOT BE DISPOSED OF WITH YOUR OTHER HOUSEHOLD
WASTE. INSTEAD, YOU NEED TO DISPOSE OF THE WASTE EQUIPMENT BY
HANDING IT OVER TO A DESIGNATED COLLECTION POINT FOR THE
RECYCLING OF WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT. FOR
MORE INFORMATION ABOUT WHERE TO DROP OFF YOUR WASTE
EQUIPMENT FOR RECYCLING, PLEASE CONTACT YOUR HOUSEHOLD
WASTE DISPOSAL SERVICE OR THE SHOP WHERE YOU PURCHASED THE
PRODUCT.
Remote Control Battery Safety Information
-
Store batteries in any cool & dry place.
Do not dispose used batteries in domestic waste. Dispose batteries at special
collection points or return to stores if applies.
Remove the batteries if they are not in use for long period of time. Battery leakage
and corrosion can damage the remote control, dispose batteries safely.
Do not mix and use old and new batteries.
Do not mix and use different types of batteries: alkaline, standard (carbon -zinc) or
rechargeable (nickel-cadmium).
Do not dispose batteries in a fire.
Do not attempt to short circuit the battery terminals.
Table of Contents
Package Contents .............................................................................................. 1
Optional Accessories ........................................................................................ 1
Get Familiar with the AVerVision F50-8M ........................................................ 2
Right Panel .............................................................................................................. 2
Rear Panel .............................................................................................................. 3
Left Panel ................................................................................................................ 3
Control Panel ........................................................................................................... 4
Remote Control ....................................................................................................... 6
Making the Connections ................................................................................... 9
Set the TV-RGB Switch Setting ............................................................................... 9
Connect to a Monitor or LCD/DLP Projector ............................................................ 9
Connect to a Monitor or LCD/DLP Projector with HDMI Output interface .............. 10
Connect to a TV ..................................................................................................... 10
Connecting the Power ........................................................................................... 11
Connect to a Computer ......................................................................................... 11
Connect to a Computer via USB............................................................................ 11
Connect to a Computer with HDMI Input interface ................................................ 12
Connect an External Microphone .......................................................................... 12
Connect an Amplified Speaker .............................................................................. 13
Connect to a Microscope ....................................................................................... 13
Setting Up AVerVision F50-8M ........................................................................ 15
Storing and Handling ............................................................................................. 15
Shooting Area ........................................................................................................ 16
Overhead Light ...................................................................................................... 17
Infrared Sensor ...................................................................................................... 17
Mounting the F50-8M on a Flat Surface ................................................................ 18
Anti-glare Sheet ..................................................................................................... 18
External Memory Storage ...................................................................................... 19
Insert an SD Card ............................................................................................. 19
Insert a USB Flash Drive .................................................................................. 19
OSD MENU........................................................................................................ 20
Navigate the Menu and Submenu ......................................................................... 21
Image .................................................................................................................... 21
Brightness ......................................................................................................... 21
Contrast ............................................................................................................ 21
49BMode ................................................................................................................. 22
51BEffect................................................................................................................. 22
8BMirror ................................................................................................................ 22
48BAdvanced .......................................................................................................... 22
48BAuto Image ....................................................................................................... 23
53BExposure .......................................................................................................... 23
54BWhite Balance................................................................................................... 23
50BFocus ................................................................................................................ 23
Presentation .......................................................................................................... 24
57BSpotlight ............................................................................................................ 24
60BVisor.................................................................................................................. 24
62BPIP .................................................................................................................... 25
63BSplit Screen ...................................................................................................... 25
64BTimer................................................................................................................. 25
Setting ................................................................................................................... 26
48BCapture ............................................................................................................. 26
6BResolution ......................................................................................................... 26
67BQuality .............................................................................................................. 26
68BType .................................................................................................................. 26
69BInterval .............................................................................................................. 26
72BStorage ............................................................................................................. 27
73BFormat .............................................................................................................. 27
76BUSB to PC ........................................................................................................ 27
5BFlicker ............................................................................................................... 27
Saturation ......................................................................................................... 27
MIC Volume ...................................................................................................... 28
System .................................................................................................................. 28
74BLanguage .......................................................................................................... 28
75BOutput Display .................................................................................................. 28
7BBackup .............................................................................................................. 28
78BSave Setting ..................................................................................................... 29
Recall Setting.................................................................................................... 29
80BInformation ........................................................................................................ 29
52BDefault .............................................................................................................. 29
Playback ................................................................................................................ 30
81BSlide Show ........................................................................................................ 30
Interval .............................................................................................................. 30
83BEffect................................................................................................................. 30
84BStorage ............................................................................................................. 30
85BDelete All .......................................................................................................... 30
WiFi ....................................................................................................................... 31
74BConnect ............................................................................................................ 31
75BSelect AP .......................................................................................................... 31
7BEnter Username and Password ........................................................................ 31
78BConnect AP ....................................................................................................... 32
Machine Name.................................................................................................. 32
Annotation ............................................................................................................. 33
Connecting a USB mouse ..................................................................................... 33
Using the Annotation ............................................................................................. 34
Transfer Captured Images/Videos to a computer .................................................. 35
Technical Specifications ................................................................................. 36
Image ................................................................................................................ 36
Optics ............................................................................................................... 36
Power ............................................................................................................... 36
Lighting ............................................................................................................. 36
Input/Output ...................................................................................................... 36
Dimension ......................................................................................................... 36
External Storage ............................................................................................... 37
Using the RS-232 Interface ............................................................................. 37
Connect to the Computer RS-232 ......................................................................... 37
RS-232 Cable Specifications .......................................................................... 38
RS-232 Transmission Specifications ............................................................. 38
RS-232 Communication Format ............................................................................ 38
RS-232 Send Command Table .............................................................................. 39
RS-232 Get Command Table................................................................................. 44
Troubleshooting ..................................................................................................... 45
Limited Warranty.............................................................................................. 46
Packa ge Contents
Make sure the following items are included in the package.
RGB Cable
USB Cable
Power Adapter (12V, 2A)
* The power adapter will vary
depending on the standard
power outlet of the country
where it is sold.
Remote Control
(batteries included)
AVerVision F50-8M
Optional Accessories
RS-232/CVBS Cable
Carrying Bag
Software & Manual CD
Anti-glare Sheet
Microscope Adapter
( 28mm and 34mm Rubber Coupler are included)
1
G e t F a m i l i a r w i t h t h e AV e r V i s i o n F 5 0 - 8 M
(fig. 1.1)
Name
(1) Camera head
(2) Camera lens
(3) LED light
(4) Flexible arm
(5)
Left panel
(6)
(7)
Control panel
IR sensor
(8)
Rear panel
(9)
Right panel
Function
Contain the camera sensor.
Focus the image in the camera.
Provide light to enhance the lighting condition.
Provide adjustable viewing coverage.
Connections for HDMI output/input external display device,
microphone, speaker, USB flash drive/USB mouse, and USB switch.
Easy access to various functions.
Receive remote control commands.
Connections for power, computer, RGB/RCA external display device,
RS-232, and USB to PC.
Connections for the camera head holder, SD card, TV-RGB display
output switch, and antitheft Kensington security lock compatible slot.
R ig ht Pa ne l
(fig. 1.2)
Name
(1) Camera Holder
(2) SD card slot
(3)
TV-RGB switch
(4)
Antitheft Slot
Function
Hold the camera head for storage.
Insert the SD card with the label facing up.
TV switches to output display video from RCA (via RS232/CVBS
adapter) to RGB OUT and HDMI OUT.
Attach a Kensington compatible security lock or antitheft device.
2
Re ar Pa nel
(fig. 1.3)
Name
(1) DC12V
(2)
RGB INPUT port
(3)
RGB OUTPUT port
(4)
RS-232/CVBS port
(5)
Mini USB port
Function
Connect the power adapter into this port.
Input the signal from a computer or other sources and pass it through
to the RGB OUT port only. Connect this port to the RGB/VGA output
port of a computer.
Connect the AVerVision F50-8M to any display device with RGB cable.
Connect the RS-232/CVBS cable (optional) into this port. The RCA jack
outputs the video signal from the camera to a TV or video equipment.
The RS-232 jack is used to connect to computer serial port or to any
control panel or for centralized control if desire.
Connect to a USB port of a computer with a USB cable and use
AVerVision F50-8M as a USB camera or transfer the captured
images/videos from the memory source to computer.
L eft Pane l
(fig. 1.4)
Name
(1)
Speaker port
(2)
MIC port
(3)
USB port
(4)
HDMI Out port
(5)
HDMI In port
Function
Connect to an amplified speaker to playback recorded audio & video
clip.
Connect a 3.5mm plug microphone. The built-in mic will be disabled
when an external MIC is connected to this port.
Insert a USB flash drive save the images/video directly from the USB
flash drive or use a USB mouse to annotate.
Output the video signal from the main system on an interactive flat
panel, an LCD monitor or LCD/DLP projector with HDMI interface using
HDMI cable.
Connect an external HDMI source as an input via this port
3
Co nt ro l Pan e l
(10)
(11)
OUTPUT
(1)
RGB
POWER
TV
RECORDING
CAMERA / PC
(2)
(3)
(4)
(5)
(6)
PLAYBACK
(12)
AUTO FOCUS
(13)
Wi - Fi
(7)
(14)
(15)
(8)
MENU
FREEZE
ROTATE
LAMP
CAP / DEL
(9)
(fig. 1.5)
Name
(1) POWER
Function
Turn the unit on/standby mode.
(2)
OUTPUT LED
(3)
RECORDING
Indicate TV-RGB switch selection to show which port the video signal
is sent out.
 TV indicates that the video signal is sent out thru RS232/CVBS
port via RCA connection.
 RGB indicates the video signal is sent out thru RGB OUT and
HDMI OUT ports.
Start/Stop audio & video recording. Audio and video recording can be
saved on a SD card or an USB Flash drive only. See External
Memory Storage.
HU
UH
(4)
WiFi LED
-
Flashing Blue: Searching WiFi router or connecting to WiFi
-
Solid Blue: Connected to WiFi router.
-
Slow Flashing Blue: Sending stream to other device/APP.
-
OFF: WiFi function is not activating.
router.
(5)
Shuttle Wheel
- Turn the shuttle wheel clockwise to zoom in and counter-clockwise
to zoom out the image in Camera and Playback mode only.
When it reaches the maximum optical zoom level of about 10X, you
can still continue to AVERZOOM up to 1.25X and 16X digital zoom.
- Press the shuttle wheel ▲,▼,◄, &► to pan the image while in
zoom in mode, to make a selection on 16-thumbnail images or
move to the next or previous single full screen preview in Playback
mode, or to make a selection and adjustment on the OSD mainmenu and sub-menu (See Menu Functions for more details).
- Use ▲&▼ to increase and decrease the video playback volume.
- Use ◄&► to play the video backward and forward.
- Move the Spotlight frame and Visor screen cover.
4
Name
(6)
(7)
FREEZE
(8) MENU
(9) ROTATE
(10) CAMERA / PC
Function
- Make a selection in Playback mode and OSD menu.
- Start/Pause video playback.
- Pause or resume image display in Camera mode.
- Stop audio & video playback in Playback mode.
Open and exit the OSD menu and submenu.
Turn the image by 0/180° in camera mode only.
Switch the video signal between camera or computer from the RGB
IN port.
(11) PLAYBACK
View & playback captured still images and video files.
(12) AUTO FOCUS
(13) WiFi
Adjust the focus automatically.
Switch between USB mode and WiFi mode.
In WiFi mode, the LED will light up (blue). Press WiFi button over 3
seconds to activate auto search for WiFi router.
Turn the overhead light on/off.
- Capture picture in Camera mode. In continuous capture mode,
press this button again to stop.
- Delete the selected picture/video in Playback mode.
Record audio when recording video clip. The recorded sound will be
in monophonic.
(14) LAMP
(15) CAP/DEL
(16) Built-in MIC
5
.
Re mote Co nt ro l
The remote control requires two (2) “AAA” size batteries (supplied), make sure batteries
are installed properly before use. You can access all the features of AVerVision F50-8M
with the remote.
(1)
(2)
(3)
(4)
Name
Function
(1)
POWER
Turn the unit on/standby.
(2)
CAMERA
(3)
RECORD
(17 )
(18 )
(19 )
(4)
CAPTURE
(20 )
(5)
VISOR
Camera mode displays the video signal
from the built-in camera.
Start/Stop audio & video recording.
Video recording can only be saved
either in a SD memory card or a USB
flash drive.
Capture still image in Camera mode. In
continuous capture mode, press this
button again to stop.
Call the Visor submenu. Visor covers
part of the presentation screen and allow
presenter to reveal the material as
desire.
In the Visor submenu, the following
options are available.
(12 )
(13 )
(14 )
(15 )
(16 )
(5)
(6)
(7)
(8)
(9)
(10 )
(21 )
(11)
(22 )
(23 )
(fig. 1.6)
ON/OFF – select to run/cancel the Visor.
Press
to move to the next
selection.
Shade – set the opacity level of the
covered area. The shaded area will
completely turns black when it is set to
level 100. Press
to move to the
next selection.
for the setting to take
OK – press
effect. If you select ON, upper part of
the presentation screen is slightly
exposed. Use the ▲,▼,◄, & ► buttons
to reveal more of the covered area; and
OFF will close the submenu.
To turn off Visor, press
(6)
ROTATE
(7)
MENU
6
again.
Rotate the image by 0/180° in Camera
mode and Playback mode.
Open and exit the OSD menu.
Name
(8)
(1)
(2)
(3)
(4)
Function
▲,▼,◄, & ►
(12 )
(13 )
(14 )
(15 )
(16 )
(5)
(6)
(7)
(17 )
(18 )
(19 )
(8)
- Pan and zoom-in image (above digital
zoom level) in both live and playback
mode.
- Select options in OSD menu.
- Use ▲&▼ to increase and decrease
the video playback volume.
- Use ◄&► to play the video
backward and forward.
-
(9)
screen cover.
(20 )
(9)
(10 )
(21 )
(11)
(22 )
(23 )
(fig. 1.6)
Move the Spotlight frame and Visor
AUTO FOCUS
Adjust the focus automatically.
(10) ZOOM +/-
Increase/decrease the image
magnification in camera and picture
playback mode.
(11) ZOOM RESET
Reset zoom level to 100%.
(12) PLAYBACK
View the captured picture/video from
the memory in 16-thumbnail images.
PC mode displays the video signal
from the RGB INPUT port of F50-8M.
(13) PC 1/2
(14) FREEZE /
STOP
- Freeze live images.
- Stop video playback.
(15) SPOTLIGHT
Call the Spotlight submenu. Spotlight
overlays a box frame on the
presentation screen. You can adjust the
box size and move it around.
In the Spotlight submenu, the following
options are available.
ON/OFF – select to run/cancel the
Spotlight. Press
to move to the
next selection.
Shade – set the opacity level of the area
outside the box. The shaded area will
completely turns black when it is set to
level 100. Press
to move to the
next selection.
Color – select the Spotlight frame color.
Press
to move to the next
selection.
7
(1)
(2)
(3)
(4)
Name
Function
(15) SPOTLIGHT
for the setting to take
OK – press
effect. If you select ON, the frame will
appear and blink, use the ▲,▼,◄, & ►
buttons to adjust the frame size and
press
to set the desired size; and
OFF will close the submenu.
(12 )
(13 )
(14 )
(15 )
(16 )
(5)
(6)
(7)
(17 )
(18 )
(19 )
(8)
To turn off Spotlight, press
(16) SPLIT
SCREEN
(9)
(20 )
(10 )
(21 )
(11)
(22 )
(23 )
(17) MODE
(fig. 1.6)
again.
Divide the screen into two. One side
displays the live image from the built-in
camera and the other side displays 8thumbnail size picture/video from the
memory.
Select from 5 type of modes:
Sharp - adjust the contrast along the
edges making text appear more visible.
Graphics - adjust the gradient of
image.
Motion - increase frame rate. Sufficient
lighting is required when using this
mode.
Microscope - automatically adjust
optical zoom for microscopic viewing.
Macro - set to view when object is only
5 – 10 cm away from the camera.
[Note] When the object is less than
10cm away from camera, the screen
resolution is only guaranteed center
80%.
Infinite - set to view when subject is at
least 80cm away from the camera.
Call the Timer submenu. Select to
Start/Pause/Stop the timer countdown
and set the timer duration.
(18) TIMER
- Make a selection in Playback mode
and OSD menu.
- Play/Pause video playback.
Turn the overhead light on/off.
(19)
(20) LAMP
(21) BRIGHTNESS
+/-
Adjust the brightness.
(22) DEFAULT
Reset to factory default setting.
8
Name
Function
(23) DEL
Delete the selected picture/video in
Playback mode.
Making the Connections
Before making the connection, make sure the power of all devices are turned off. If you are
not sure on where to connect, simply follow the illustrated connections below and also refer
to the user manual of the device you are connecting the AVerVision F50-8M with.
S e t t h e T V- R G B S w i t c h S e t t i n g
The TV-RGB switch determines the display output selection. Switch it to RGB (right) to
output signal using RGB/HDMI connection and TV (left) to output signal using RCA
connection. (see fig. 1.2 # 3)
Switch
AVerVision Port
Display Device Port
RGB OUTPUT
RGB INPUT
RGB
HDMI OUTPUT
To
HDMI INPUT
TV
RS232/CVBS
(use RS-232/CVBS cable)
(Optional)
VIDEO IN
Connect to a Monitor or LCD/DLP Pr ojector
Locate the RGB (VGA) input port of the graphics display device and connect it to RGB
OUT port of AVerVision F50-8M.
Make sure the TV/RGB switch is set to RGB.
9
Connect to a Monitor or LCD/DLP Pr ojector with
HDMI Output interface
Locate the HDMI input port of the display device and connect it to HDMI out port of
AVerVision F50-8M.
Make sure the TV/RGB switch is set to RGB.
Connect to a TV
Locate the VIDEO or SCART RGB (if applicable) input port of the TV or Video equipment
(i.e., VCR) to record your presentation and connect it to RCA jack of RS-232/CVBS cable
(optional).
10
C o n n e c t i n g t h e Pow e r
Connect the power adapter to a standard 100V~240V AC power outlet. The unit
automatically in standby mode once the power is connected. Press
to turn on.
Connect to a Computer
Locate the RGB (VGA) output port of the computer or laptop and connect it to RGB IN port
of AVerVision F50-8M. The video signal from the RGB IN port is streamed to RGB OUT.
- To display computer image, press Camera/PC button on the control panel or
remote control to switch AVerVision F50-8M to computer mode.
- For laptop to output display image, use the keyboard command (FN+F5) to
switch between the display modes. For different command, please refer to
your laptop manual.
Connect to a Computer via USB
Locate the USB port of the computer or laptop and connect it to PC port of AVerVision
F50-8M.
11
Connect to a Computer with HDMI Input interface
Locate the HDMI output port of the computer of laptop and connect it to HDMI in port of
AVerVision F50-8M.
- Make sure the TV/RGB switch is set to RGB.
- To display computer image, press Camera/PC button on the control panel or
remote control to switch AVerVision F50-8M to computer mode.
- For laptop to output display image, use the keyboard command (FN+F5) to
switch between the display modes. For different command, please refer to
your laptop manual.
Connect an Exter nal Microphone
Plug a 3.5mm mono microphone to
port. The built-in microphone on the control panel
will be disabled when an external microphone is connected. The recorded audio will be in
monophonic sound.
12
C o n n e c t a n A m p l i f i e d S p e a ke r
Plug a 3.5mm plug amplified speaker to
port. Only the audio from the video playback is
supported.
We recommend connecting an amplified speaker to the Audio output port.
Take caution when using earphones. Adjust the volume down on the
remote to prevent hearing damage due to loudness.
Connect to a Microscope
Connect the AVerVision F50-8M to a microscope enables you to examine microscopic
objects on a big screen.
1.
Change the image display mode to
Microscope. Press MENU > select
IMAGE tab > select MODE > select
(microscope) and press
.
2.
Aim the camera head at the farthest
point and press AUTO FOCUS.
3.
Adjust the focus of the microscope.
13
4.
Select the appropriate rubber coupler
size for the microscope eyepiece and
insert it in the microscope adapter.
5.
Remove the microscope eyepiece from
the microscope and connect it to the
microscope adapter with the rubber
coupler inserted. Fasten the 3 bolts until
the adapter secures the eyepiece.
- For the eyepiece, we suggest
using 33mm eye relief or higher.
- Do the adjustment manually to
get better image view.
6.
Attach the microscope adapter to the
AVerVision camera head. Then connect
it to the AVerVision and microscope.
Make sure the arrow on the camera
head and microscope adapter are on
the same side to connect and twist
clockwise for the arrows to meet and
lock.
14
S e t t i n g U p AV e r V i s i o n F 5 0 - 8 M
This section provides useful tips on how to adjust the AVerVision F50-8M to meet your
needs.
Storing and Handling
The gooseneck design allows you to freely bend the arm and store the camera head in the
camera holder. Once you have properly secured the camera head to the camera holder,
you may use the arm to carry AVerVision F50-8M.
15
Shooting Area
The shooting area can view an area of 400x300mm which allows you to show an A4 size
portrait paper.
If the camera head is in upright position, press ROTATE on the control panel or remote
control twice to rotate the image in 180°.
To mirror the image, press MENU > select Mirror, press
16
, and select On.
O ve r h e a d L i g h t
Press LAMP button on the control panel or remote control to turn on and off light.
Infrared Sensor
Aim the remote control at the infrared sensor to operate the unit.
17
Mounting the F50-8M on a F lat Surface
Measure and mark the horizontal of 75 mm from the center line distance between the holes
on the flat surface as describe in the illustration below. Use 2 pieces of M4.0 screws for 6
mm holes and secure the F50-8M on the flat surface.
75mm
Anti-glare Sheet
The anti-glare sheet is a special coated film that helps eliminate any glare that maybe
encountered while displaying very shiny objects or glossy surfaces such as magazines and
pictures. To use, simply place the anti-glare sheet on top of the shiny document to reduce
reflected light.
18
Exter nal Memor y Storage
AVerVision F50-8M supports both SD memory card and USB flash drive for more image
capture and audio & video recordings. AVerVision F50-8M can detect when there is an
external storage media and automatically switch to the last detected storage. If no external
storage is connected, all captured still images will be saved in the built-in memory.
Insert an SD Card
Insert the card with the contact facing down until it reaches the end. To remove the card,
push to eject and pull the card out. The supported SD card capacity is from 1GB to 32GB
(FAT32). We recommend using SDHC card with class-6 or above for high quality recording.
Insert a USB Flash Drive
Connect the USB flash drive in the USB slot. AVerVision F50-8M can support USB flash
drive from 2GB to 64GB (FAT32). UBest to format the USB flash drive using AVerVision
F50-8M for better video recordingU.
19
OSD MENU
There are 4 tabs on the OSD menu: IMAGE, PRESENTATION, SETTING and SYSTEM. In
Playback mode, you can access PLAYBACK OSD menu to enable the Slide Show feature
and modify Slide Show interval and transition setting if desire.
For TV output, the RESOLUTION will be disabled in SETTING menu list.
IMAGE
PRESENTATION
SETTING
SYSTEM
ANNOTATION
PLAYBACK
20
N avi g ate t h e Me n u a n d S u b m en u
1. Press MENU button on the remote or control
panel.
2. Press ► and ◄ to toggle between tabs
3. Press ▼ and ▲ to choose a selection in the
menu list.
4. Press
to make a selection.
5. Use ► and ◄ to adjust the setting or make a
selection.
6. Press
to enter submenu.
7. Press MENU to close the OSD menu.
Image
Menu Screen
Function
Brightness
Adjust brightness level manually between 1 and 64.
Contrast
Adjust the contrast level manually between 1 and 32
under bright and dark environments.
21
Menu Screen
Function
Mode
Select from the various image display settings.
49B
Sharp - adjust the contrast along the edges making
text appear more visible.
Graphics - adjust the gradient of image.
Motion - increase frame rate. Sufficient lighting is
required when using this mode.
Microscope - automatically adjust optical zoom for
microscopic viewing.
Macro - set to view when object is only 5 cm – 10cm
away from the camera.
Infinite - set to view when subject is at least 80cm
away from the camera.
Effect
Convert the image into positive (true color), monochrome
(black and white) or negative.
51B
Mirror
Select to flip the image in Camera mode.
8B
Advanced
Select to set the Auto Image, Exposure, and White
Balance settings.
48B
22
Menu Screen
Function
Auto Image
Select ON or OFF to automatically adjust the white
balance and exposure setting, and correct the color and
exposure compensation.
48B
Exposure
Select the exposure setting.
AUTO - automatically adjust the camera exposure and
the amount of light required.
MANUAL - manually adjust the exposure level. The
exposure can be adjusted up to 100.
53B
White Balance
Select the White Balance setting for various light
conditions or color temperature.
AUTO - automatically adjust the white balance.
54B
MANUAL - manually adjust the red and blue color level.
The color level can be adjusted up to 255.
Focus
Manually adjust the focus.
50B
23
Pr esentation
Menu Screen
Function
Spotlight
Spotlight overlays a frame on the presentation screen.
You can move the Spotlight around the presentation
screen using the ▲,▼,◄, & ► buttons. Select Execute
to call the Spotlight submenu.
57B
In the Spotlight submenu, the following options are available.
ON/OFF – select to run/cancel the Spotlight. Press
to
move to the next selection.
Shade – set the opacity level of the area outside the box.
The shaded area will completely turns black when it is set
to level 100. Press
to move to the next selection.
Color – select the Spotlight frame color. Press
move to the next selection.
to
OK – press
for the setting to take effect. If you select
ON, the frame will appear and blink, use the ▲,▼,◄, &
► buttons to adjust the frame size and press
to set
the desired size; and OFF will close the submenu.
Visor
Visor covers the presentation
screen. The upper part of the
presentation screen is slightly
exposed. Use the ▲,▼,◄, & ►
buttons to reveal more of the
covered area. Select Execute to call
the Visor submenu.
60B
24
Menu Screen
Function
In the Visor submenu, the following options are available.
ON/OFF – select to run/cancel the Visor. Press
to move to
the next selection.
Shade – set the opacity level of the covered area. The shaded
area will completely turns black when it is set to level 100. Press
to move to the next selection.
for the setting to take effect. If you select ON,
OK – press
upper part of the presentation screen is slightly exposed. Use the
▲,▼,◄, & ► buttons to reveal more of the covered area; and
OFF will close the submenu.
Split Screen
Divide the screen into two parts. Half of the screen
displays the 8-thumbnail images and the other half
display the image from the AVerVision F50-8M camera.
Select the display location of the 8- thumbnail playback
images. Select OFF to cancel Split Screen.
63B
Left
Right
Top
Below
PIP
Select the thumbnail playback screen location and show
the thumbnail playback screen at the corner of the
screen to recall the captured image from the memory in
Camera mode. Select OFF to cancel PIP.
62B
Lower Left
Upper Left
Upper Right
Lower Right
Timer
Start/Pause/Stop the timer and set the timer duration.
The timer automatically counts up after the count down
reaches zero to show the elapsed time. Even when you
switch between Playback, PC or Camera modes, the
timer will continue.
64B
25
Setting
Menu Screen
Function
Capture
Select to set the capture resolution, quality, type and
interval settings.
48B
Resolution
Select the capture size. In 8M setting, the capture
resolution size is 3840 X 2160.
6B
Quality
Select the capture compression setting.
67B
Type
Select the capture type.
Single - capture one picture only.
Continuous - capture successive pictures.
68B
Interval
Set the time interval for continuous capture. The length
can be set up to 600 sec (10 min).
69B
26
Menu Screen
Function
Storage
Change the storage location. Audio & video recording
can only be saved in SD memory card or USB flash
drive.
72B
Format
Format to delete all the data in the selected memory.
73B
USB to PC
Select the status of the AVerVision F50-8M when it is
connected to the computer via USB.
76B
Camera - can be used as a computer webcam or with
our bundled software to record video and capture still
image.
Storage - transfer the captured pictures/videos from the
memory to computer hard disk.
Flicker
Select between 50Hz or 60Hz. Some display devices
cannot handle high refresh rates. The image will flicker a
couple of times as the output is switched to another
refresh rate.
5B
Saturation
Adjust the value of saturation.
27
Menu Screen
Function
MIC Volume
Adjust volume input of recording or USB audio input.
System
Menu Screen
Function
Language
Change and select different language.
74B
Output Display
Set the resolution to display the image on screen. This
selection will be disabled in TV output mode.
75B
Backup
Copy the image from the built-in memory to SD card or
USB flash drive.
7B
28
Menu Screen
Function
Save Setting
Save current setting in the selected profile number. Only
effect, mode, brightness and contrast settings can be
saved.
78B
Recall Setting
Restore the setting back to the selected profile number.
Information
Display the product information.
80B
Default
Restore all the settings into original factory default
setting.
52B
29
P l a y b a ck
Menu Screen
Function
Slide Show
Display all captured still pictures in an automated slide
show. The video file will be skipped.
81B
Interval
Set the interval before displaying the next picture. The
length can be set up to 100 sec.
Effect
Select the slide show transition effect.
83B
Slide image
Split Vertical Out
Checker down
Split Horizontal In
Wipe down
Storage
Select the source of the images.
84B
Delete All
Permanently delete all the data in selected memory
source. A Warning Message will appear. Select YES to
continue and NO to stop formatting the storage.
85B
30
W iFi
WiFi is an optional function. Only WiFi dongle is installed and WiFi button is pressed (on control panel),
the WiFi function page will show.
OUTPUT
RGB
POWER
TV
RECORDING
CAMER A / PC
PLAYBACK
AUTO FOCUS
Wi - Fi
MENU
Menu Screen
FREEZE
ROTATE
LAMP
CAP / DEL
Function
Connect
Select AP, enter Password of AP, and make a connection
with selected AP.
74B
Select AP
75B
Press
to expend AP list that F50-8M has detected on you
LAN network. Use ▲ and ▼ buttons to move to the AP that you
want to select. Press
to confirm.
Enter Username and Password
7B
Use ▼ button move to username/password column. Press
to call out on-screen keyboard. Use ▲,▼,◄, ►&
to select
the characters. Use the “Back” key to delete unwanted
characters. When is done, select Enter to complete.
If you want check password during enter password, mark Show
Password option.
31
Menu Screen
Function
Connect AP
78B
Use ▼ button move to “Connect” and press
to start
connection. When connection is successful, the AP information
is displayed.
To disconnect, select “Disconnect” and press
.
To remember this AP account, mark Remember Me.
To back to WiFi page, select “OK” and press
.
Machine Name
Give a name for the DocCam. Use ▼ button move to
“Machine Name” and press
to call out on-screen keyboard.
Then, Use ▲,▼,◄, ►&
to enter the name. This name will
be an identity in Sphere application for user to recognize.
32
Annotation
In single image playback mode and preview mode, you can use the annotation feature to
overlay straight line or freeform line on the captured image with the USB mouse connected
to the USB port of AVerVision F50-8M. It comes with the following selections: Color Palette,
Line Thickness, Line, Freehand, Capture, Eraser, and Hide/Show icons.
Connecting a USB mouse
Connect the USB cable to the USB slot of AVerVision F50-8M.
33
Using the Annotation
1. In camera mode, press
(Freeze/Stop) button to call out annotation menu.
on the remote. Then, use the ▲,▼,◄, & ►
buttons and select the image you want to annotate in the 16-thumbnail preview. Press
to make a selection and display the image in full screen. The annotation menu will
appear on the upper left corner of the screen.
2. In playback back mode, Press
3. Use the mouse and move the “+” cursor on the item in the annotation panel you want to
use. Then left click the mouse button to make a selection.
Name
Function
Color Palette
Line Thickness
Line
Freehand
Capture
Select the line color.
Select the thickness of the line.
Select to draw a straight line.
Select to draw freeform line.
Capture the image with the annotation and save it as a new file.
Select to erase any part of the annotation that it comes in
contact with or delete all annotation.
Shrink or expand the annotation menu.
Eraser
Hide/Show
34
Tr a n s f e r C a p t u r e d I m a g e s / V i d e o s t o a c o m p u t e r
This enables you to transfer the captured image from the built-in memory or SD to a
computer.
The instruction below MUST be read and followed BEFORE connecting the
USB cable.
1. MUST set the USB to PC as STORAGE before connecting the USB cable.
2. When “Mass Storage Start…” appears at the lower right corner of the presentation
screen, you may now connect the USB cable.
3. Upon connecting the USB cable, the system automatically detects the new removable
disk. You can now transfer the captured image(s) from the F50-8M built-in memory to
U
the computer hard disk.
35
U
Te c h n i c a l S p e c i f i c a t i o n s
Image
Sensor
1/3.2” CMOS
Pixel Count
8 megapixels
Frame Rate
60 fps (max.)
White Balance
Auto / Manual
Exposure
Auto / Manual
Image mode
Sharp / Graphics / Motion / Microscope / Macro / Infinite
Effect
Color / B/W / Negative / Mirror / Rotate / Freeze
RGB output
1920x1080, 1280x1024, 1280x720, 1024x768, 1280 x 800,
1366x768
HDMI Output
HD 1080p 60Hz; HD 720p 60Hz
Image Capture
240 Frames(XGA)
Optics
Focusing
Auto / Manual
Shooting Area
400mm x 300mm
Zooming
Total 200X (10X optical zoom + 1.25AVERZOOM
Digital zoom)
TM
+ 16X
Power
Power Source
DC 12V, 100-240V, 50-60Hz
Consumption
14 Watts(lamp on); 13.3 Watts(lamp off)
Lighting
Lamp Type
LED light
Input/Output
RGB Input
15-Pins D-sub (VGA)
RGB Output
15-Pins D-sub (VGA)
HDMI Output
HDMI
HDMI Input
HDMI
CVBS/RS-232
Mini-DIN Jack (use CVBS/RS-232 Adapter cable_optional)
Composite Video
RCA Jack
USB
USB2.0
DC 12V Input
Power Jack
MIC
Phone Jack
Speaker
Phone Jack
Dimension
Operating
380mm*200mm*540mm (+/-2mm include rubber foot)
Folded
305mm x 245mm x 77mm (+/-2mm include rubber foot)
Weight
2.56 kg (about 5.64lbs)
36
External Storage
Secure Digital
(SDHC)
1GB ~ 32GB (FAT32)
USB Flash Drive
2GB ~ 64GB (FAT32)
Using the RS-232 Interface
AVerVision F50-8M can be controlled using a computer or any centralized control panel
through RS-232 connection. The command code for RS-232 is provided for the system
integrator to be able to incorporate it with the system program.
Connect to the Computer RS-232
Locate the RS-232 port of the computer and connect it to RS-232 jack of RS-232/CVBS
cable(optional).
37
R S - 2 3 2 C a b l e S p e c i f i c at i o n s
Make sure the RS-232 cable matches the cable specification design.
R S - 2 3 2 Tr a n s m i s s i o n S p e c i f i c a t i o n s






Start bit
Data bit
Stop bit
Parity bit
X parameter
Baud rate (Communication speed)
:1 bit
:8 bit
:1 bit
:None
:None
:9600bps
R S - 2 3 2 C o m m u n i c a t i o n Fo r m at
Send Device
Code(1 Byte)
Type Code
(1 Byte)
Data Length
Code(1 Byte)
Data[0] Code
(1 Byte)
Data[1] Code
(1 Byte)
Data[2] Code
(1 Byte)
Receive Device
Code
(1 Byte)
CheckSum Code
(1 Byte)
Format
Example
0x52
0x0B
0x0A
0x03
0x01
RS-232 Send Command Table
RS-232 Get Command Table
RS-232 Send Command Table
X
RS-232 Send Command Table
X
0x53
RS-232 Send Command Table
RS-232 Get Command Table
Send Device + Type + Length +
Data + Receive Data + CheckSum
Power On Command:
0x52 + 0x0B + 0x03 + 0x01 +
0x01 + 0x00 + 0x53 + 0x5B
Send Device + Type + Length +
Data + Receive Data + CheckSum
Get WB Red Value :
0x52 + 0x0A + 0x01+ 0x02+ 0x53
+ 0x5A
38
R S - 2 3 2 S e n d C o m m a n d Ta b l e
Send Format︰0x52 + 0x0B + 0x03 + Data[0] + Data[1] + Data[2] + 0x53 + CheckSum*1
Receive Format︰0x53 + 0x00 + 0x02+ *2 + 0x00 + 0x52 + ReCheckSum*4
Abnormal Receive Format︰0x53 + 0x00 + 0x01 + *3 + 0x52 + ReCheckSum*5
xor : Exclusive-or operator
*1 :CheckSum = 0x0B xor 0x03 xor Data[0] xor Data[1] xor Data[2] xor 0x53
*2 :Receive Success Check Code : 0x0B(Success Command),0x03(Invalid Command)
*3 :Abnormal Receive Check Code : 0x01(Type Fail),0x02(CheckSum Fail),0x04
(Invalid Command)
*4 :ReCheckSum = 0x00 xor 0x02 xor *2 xor 0x00 xor 0x52
*5 :ReCheckSum* = 0x00 xor 0x01 xor *3 xor 0x52
*6 : StandBy Mode Power Off Receive Format : 0x51 + 0xFF + 0x01 + 0x0B + 0x51 +
0xA4
*7 : StandBy Mode Power On Receive Format : 0x51 + 0x00 + 0x01 + 0x0B + 0x51 +
0x5B
Function
Data[0]
Data[1]
Data[2]
CheckSum
POWER OFF*6
0x01
0x00
0x00
0x5a
POWER ON*7
0x01
0x01
0x00
0x5b
CAMERA MODE
0x02
0x00
0x00
0x59
PLAYBACK MODE
0x03
0x00
0x00
0x58
PC-1 PASS THROUGH
0x04
0x00
0x00
0x5f
IMAGE CAPTURE TYPE: SINGLE
0x05
0x00
0x00
0x5e
IMAGE CAPTURE TYPE: CONTINUOUS
0x05
0x01
0x00
0x5f
CONT. CAPTURE INTERVAL +
0x06
0x00
0x00
0x5d
CONT. CAPTURE INTERVAL -
0x06
0x01
0x00
0x5c
NORMAL IMAGE CAPTURE
0x07
0x00
0x00
0x5c
8M IMAGE CAPTURE
0x07
0x01
0x00
0x5d
TIMER START
0x08
0x00
0x00
0x53
TIMER PAUSE
0x08
0x01
0x00
0x52
TIMER STOP
0x08
0x02
0x00
0x51
*1
TIMER SET TIME
0x08
0x03
VALUE[ 1 ~
120 ]
PREVIEW MODE: SHARP
0x0A
0x00
0x00
0x51
PREVIEW MODE: GRAPHIC
0x0A
0x01
0x00
0x50
39
Function
Data[0]
Data[1]
Data[2]
CheckSum
PREVIEW MODE: MOTION
0x0A
0x02
0x00
0x53
PREVIEW MODE: MICROSCOPE
0x0A
0x03
0x00
0x52
PREVIEW MODE: MACRO
0x0A
0x04
0x00
0x55
PREVIEW MODE: INFINITE
0x0A
0x05
0x00
0x54
PREVIEW MODE CAPTURE
0x0B
0x00
0x00
0x50
PLAYBACK DELETE
0x0C
0x00
0x00
0x57
PLAYBACK FULL SCREEN
0x0D
0x00
0x00
0x56
MIRROR OFF
0x0E
0x00
0x00
0x55
MIRROR ON
0x0E
0x01
0x00
0x54
ROTATE OFF
0x0F
0x00
0x00
0x54
ROTATE ON
0x0F
0x02
0x00
0x56
EFFECT: COLOR
0x10
0x00
0x00
0x4b
EFFECT: B/W
0x10
0x01
0x00
0x4a
EFFECT: NEGATIVE
0x10
0x02
0x00
0x49
CONTRAST INCREASE
0x11
0x00
0x00
0x4a
CONTRAST DECREASE
0x11
0x01
0x00
0x4b
*1
CONTRAST VALUE
0x11
0x02
VALUE[ 1 ~
32 ]
BRIGHTNESS INCREASE
0x12
0x00
0x00
0x49
BRIGHTNESS DECREASE
0x12
0x01
0x00
0x48
BRIGHTNESS VALUE
0x12
0x02
VALUE[ 1 ~
64 ]
*1
EXPOSURE: AUTO
0x13
0x00
0x00
0x48
EXPOSURE: MANUAL
0x13
0x01
0x00
0x49
EXPOSURE MANUAL INCREASE
0x14
0x00
0x00
0x4f
EXPOSURE MANUAL DECREASE
0x14
0x01
0x00
0x4e
WHITE BALANCE: AUTO
0x15
0x00
0x00
0x4e
WHITE BALANCE: MANUAL
0x15
0x01
0x00
0x4f
WHITE BALANCE BLUE INCREASE
0x16
0x00
0x00
0x4d
WHITE BALANCE BLUE DECREASE
0x16
0x01
0x00
0x4c
40
Function
Data[0]
Data[1]
Data[2]
CheckSum
WHITE BALANCE RED INCREASE
0x17
0x00
0x00
0x4c
WHITE BALANCE RED DECREASE
0x17
0x01
0x00
0x4d
FLICKER: 50Hz
0x18
0x00
0x00
0x43
FLICKER: 60Hz
0x18
0x01
0x00
0x42
SPOTLIGHT: OFF
0x19
0x00
0x00
0x42
SPOTLIGHT: ON
0x19
0x01
0x00
0x43
SPOTLIGHT SHADE: 0% DARK
0x1A
0x00
0x00
0x41
SPOTLIGHT SHADE: 50% DARK
0x1A
0x01
0x00
0x40
SPOTLIGHT SHADE: 100% DARK
0x1A
0x02
0x00
0x43
SPOTLIGHT COLOR: RED
0x1B
0x00
0x00
0x40
SPOTLIGHT COLOR: GREEN
0x1B
0x01
0x00
0x41
SPOTLIGHT COLOR: BLUE
0x1B
0x02
0x00
0x42
SPOTLIGHT RESIZE
0x1C
0x00
0x00
0x47
VISOR: OFF
0x1D
0x00
0x00
0x46
VISOR: ON
0x1D
0x01
0x00
0x47
VISOR SHADE: 50% DARK
0x1E
0x00
0x00
0x45
VISOR SHADE: 100% DARK
0x1E
0x01
0x00
0x44
PIP: OFF
0x1F
0x00
0x00
0x44
PIP: ON
0x1F
0x01
0x00
0x45
PIP POSITION: BOTTOM LEFT
0x20
0x00
0x00
0x7b
PIP POSITION: TOP LEFT
0x20
0x01
0x00
0x7a
PIP POSITION: TOP RIGHT
0x20
0x02
0x00
0x79
PIP POSITION: BOTTOM RIGHT
0x20
0x03
0x00
0x78
SPLITSCREEN: OFF
0x21
0x00
0x00
0x7a
SPLITSCREEN: ON
0x21
0x01
0x00
0x7b
SPLITSCREEN DIR: UPPER SCREEN
0x22
0x00
0x00
0x79
SPLITSCREEN DIR: LOWER SCREEN
0x22
0x01
0x00
0x78
SPLITSCREEN DIR: LEFT SCREEN
0x22
0x02
0x00
0x7b
SPLITSCREEN DIR: RIGHT SCREEN
0x22
0x03
0x00
0x7a
41
Function
Data[0]
Data[1]
Data[2]
CheckSum
RECORDING: OFF
0x23
0x00
0x00
0x78
RECORDING: ON
0x23
0x01
0x00
0x79
MOVIE FAST REWIND
0x25
0x00
0x00
0x7e
MOVIE FAST FORWARD
0x25
0x01
0x00
0x7f
MOVIE VOL INC
0x26
0x00
0x00
0x7d
MOVIE VOL DEC
0x26
0x01
0x00
0x7c
STORAGE: EMBEDDED
0x28
0x00
0x00
0x73
STORAGE: SD CARD
0x28
0x01
0x00
0x72
STORAGE: THUMB DRIVE
0x28
0x02
0x00
0x71
FORMAT: EMBEDDED
0x29
0x00
0x00
0x72
FORMAT: SD CARD
0x29
0x01
0x00
0x73
FORMAT: THUMB DRIVE
0x29
0x02
0x00
0x70
OUTPUT RESOLUTION: 1024x768
0x2F
0x01
0x00
0x75
OUTPUT RESOLUTION: 1280x720
0x2F
0x02
0x00
0x76
OUTPUT RESOLUTION: 1920x1080
0x2F
0x03
0x00
0x77
OUTPUT RESOLUTION: 1280x1024
0x2F
0x04
0x00
0x70
OUTPUT RESOLUTION: 1280x800
0x2F
0x06
0x00
0x72
OUTPUT RESOLUTION: 1366x768
0x2F
0x07
0x00
0x72
USB CONNECT: USB CAMERA
0x30
0x00
0x00
0x6b
USB CONNECT: MASS STORAGE
0x30
0x01
0x00
0x6a
BACKUP TO SD CARD
0x31
0x00
0x00
0x6a
BACKUP TO THUMBDRIVE
0x31
0x01
0x00
0x6b
PROFILE SAVE: PROFILE 1
0x32
0x00
0x00
0x69
PROFILE SAVE: PROFILE 2
0x32
0x01
0x00
0x68
PROFILE SAVE: PROFILE 3
0x32
0x02
0x00
0x6B
PROFILE RECALL: PROFILE 1
0x33
0x00
0x00
0x68
PROFILE RECALL: PROFILE 2
0x33
0x01
0x00
0x69
PROFILE RECALL: PROFILE 3
0x33
0x02
0x00
0x6a
42
Function
Data[0]
Data[1]
Data[2]
CheckSum
SLIDESHOW: OFF
0x34
0x00
0x00
0x6f
SLIDESHOW: ON
0x34
0x01
0x00
0x6e
SLIDESHOW EFFECT: EFFECT 0
0x35
0x00
0x00
0x6e
SLIDESHOW EFFECT: EFFECT 1
0x35
0x01
0x00
0x6f
SLIDESHOW EFFECT: EFFECT 2
0x35
0x02
0x00
0x6c
SLIDESHOW EFFECT: EFFECT 3
0x35
0x03
0x00
0x6d
SLIDESHOW EFFECT: EFFECT 4
0x35
0x04
0x00
0x6a
SLIDESHOW EFFECT: EFFECT 5
0x35
0x05
0x00
0x6b
AUTO IMAGE:OFF
0x36
0x00
0x00
0x6d
AUTO IMAGE:ON
0x36
0x01
0x00
0x6c
CAPTURE QUALITY: NORMAL
0x37
0x00
0x00
0x6c
CAPTURE QUALITY: HIGH
0x37
0x01
0x00
0x6d
CAPTURE QUALITY: FINEST
0x37
0x02
0x00
0x6e
AUTO FOCUS
0x40
0x00
0x00
0x1b
MENU
0x41
0x00
0x00
0x1a
ARROW - DOWN
0x42
0x00
0x00
0x19
ARROW - UP
0x42
0x01
0x00
0x18
ARROW - LEFT
0x42
0x02
0x00
0x1b
ARROW - RIGHT
0x42
0x03
0x00
0x1a
ENTER
0x43
0x00
0x00
0x18
FREEZE
0x44
0x00
0x00
0x1f
DEFAULT
0x45
0x00
0x00
0x1e
ZOOM -
0x46
0x00
0x00
0x1d
ZOOM +
0x46
0x01
0x00
0x1c
ZOOM RESET
0x47
0x00
0x00
0x1c
NEAR
0x48
0x00
0x00
0x13
FAR
0x48
0x01
0x00
0x12
LAMP OFF
0x49
0x00
0x00
0x12
LAMP ON
0x49
0x01
0x00
0x13
SATURATION INCREASE
0x4B
0x00
0x00
0x10
43
Function
Data[0]
SATURATION DECREASE
0x4B
SATURATION VALUE
0x4B
Data[1]
Data[2]
CheckSum
0x01
0x00
0x11
0x02
VALUE[ 1 ~
32]
*1
R S - 2 3 2 G e t C o m m a n d Ta b l e
Send Format︰0x52 + 0x0A + 0x01 + Data[0] + 0x53 + CheckSum
Receive Format︰0x53 + 0x0C + 0x01 + ReData[0] + 0x52 + ReCheckSum*1
xor : Exclusive-or operator
*1 :ReCheckSum = 0x0C xor 0x01 xor ReData[0] xor 0x52
*2 : Get Power Off Status Receive Format : 0x51 + 0xFF + 0x01 + 0x0A + 0x51 + 0xA5
Function
Data[0]
CheckSum
RED VALUE
0x02
0x5A
VALUE[ 0 ~ 255 ]
BLUE VALUE
0x03
0x5B
VALUE[ 0 ~ 255 ]
POWER STATUS
0x04
0x5C
OFF *2
1: ON
LAMP STATUS
0x05
0x5D
0 : OFF 1: ON
DISPLAY STATUS
0x06
0x5E
0: CAMERA MODE
1: PLAYBACK MODE
2: PC-1 PASS THROUGH
VIDEO OUTPUT STATUS
0x07
0x5F
0: VGA 1: TV
FREEZE STATUS
0x08
0x50
0 : OFF 1: ON
BRIGHTNESS VALUE
0x0A
0x52
VALUE[ 1 ~ 64 ]
CONTRAST VALUE
0x0B
0x53
VALUE[ 1 ~ 32 ]
SATURATION VALUE
0x0D
0x55
VALUE [ 1 ~ 32 ]
44
ReData[0]
Tr o u b l e s h o o t i n g
This section provides many useful tips on how to solve common problems while using the
AVerVision F50-8M.
There is no picture on the presentation screen.
1. Check all the connectors again as shown in this manual.
2. Check the on/off switch of the display output device.
3. Verify the setting of the display output device.
4. If you are presenting from a notebook or computer through the display output device, check the
cable connection from computer RGB (VGA) output to RGB input of AVerVision F50-8M and make
sure AVerVision F50-8M is in PC Mode.
I have set up the AVerVision F50-8M and checked all the connections as specified in
the manual but I cannot get a picture on the preferred presentation screen.
1. Once the power is connected the unit is set to standby mode. Press the POWER button to turn on.
2. If your display output device is on TV or any analog device, please switch the TV-RGB dip switch
to TV.
The picture on the presentation screen is distorted or the image is blurry.
1. Reset all changed settings, if any, to the original manufacturer default setting. Press MENU then
go to SYSTEM > Default and select YES in the OSD menu.
2. Use the Brightness and Contrast menu functions to reduce the distortion if applicable.
3. If you discover that the image is blurry or out of focus, press the Auto Focus button on the control
panel or remote control.
There is no computer signal on presentation screen.
1. Check all the cable connections among the display device, AVerVision F50-8M and your PC.
2. Connect your PC to the AVerVision F50-8M first before you power on your computer.
3. For notebook, repeatedly press FN+F5 to toggles between display modes and display the
computer image on the presentation screen. For different command, please refer to your laptop
manual.
The presentation screen does not show the exact desktop image on my PC or
Notebook after I toggle from Camera to PC mode.
1. Return to your PC or Notebook, place the mouse on the desktop and right click, choose
“Properties”, choose “Setting” tab, click on “2” monitor and check the box “Extend my Windows
desktop onto this monitor”.
2. Then go back one more time to your PC or Notebook and place the mouse on the desktop and
right click again.
3. This time choose “Graphics Options”, then “Output To”, then “Intel® Dual Display Clone”, and then
choose “Monitor + Notebook”.
4. After you follow these steps, you should be able to see the same desktop image on your PC or
Notebook as well as on the presentation screen.
45
Li m i ted War r anty
For a period of time beginning on the date of purchase of the applicable product and extending as set
forth in the “Warranty Period of AVer Product Purchased” section of the warranty card, AVer
Information, Inc. (“AVer”) warrants that the applicable product (“Product”) substantially conforms to
AVer’s documentation for the product and that its manufacture and components are free of defects in
material and workmanship under normal use. “You” as used in this agreement means you individually
or the business entity on whose behalf you use or install the product, as applicable. This limited
warranty extends only to You as the original purchaser. Except for the foregoing, the Product is
provided “AS IS.” In no event does AVer warrant that You will be able to operate the Product without
problems or interruptions, or that the Product is suitable for your purposes. Your exclusive remedy
and the entire liability of AVer under this paragraph shall be, at AVer’s option, the repair or replacement
of the Product with the same or a comparable product. This warranty does not apply to (a) any Product
on which the serial number has been defaced, modified, or removed, or (b) cartons, cases, batteries,
cabinets, tapes, or accessories used with this product. This warranty does not apply to any Product
that has suffered damage, deterioration or malfunction due to (a) accident, abuse, misuse, neglect, fire,
water, lightning, or other acts of nature, commercial or industrial use, unauthorized product
modification or failure to follow instructions included with the Product, (b) misapplication of service by
someone other than the manufacturer’s representative, (c) any shipment damages (such claims must
be made with the carrier), or (d) any other causes that do not relate to a Product defect. The Warranty
Period of any repaired or replaced Product shall be the longer of (a) the original Warranty Period or (b)
thirty (30) days from the date of delivery of the repaired or replaced product.
Limitations of Warranty
AVer makes no warranties to any third party. You are responsible for all claims, damages, settlements,
expenses, and attorneys’ fees with respect to claims made against You as a result of Your use or
misuse of the Product. This warranty applies only if the Product is installed, operated, maintained, and
used in accordance with AVer specifications. Specifically, the warranties do not extend to any failure
caused by (i) accident, unusual physical, electrical, or electromagnetic stress, neglect or misuse, (ii)
fluctuations in electrical power beyond AVer specifications, (iii) use of the Product with any accessories
or options not furnished by AVer or its authorized agents, or (iv) installation, alteration, or repair of the
Product by anyone other than AVer or its authorized agents.
Disclaimer of Warranty
EXCEPT AS EXPRESSLY PROVIDED OTHERWISE HEREIN AND TO THE MAXIMUM EXTENT
PERMITTED BY APPLICABLE LAW, AVER DISCLAIMS ALL OTHER WARRANTIES WITH RESPECT
TO THE PRODUCT, WHETHER EXPRESS, IMPLIED, STATUTORY OR OTHERWISE, INCLUDING
WITHOUT LIMITATION, SATISFACTORY QUALITY, COURSE OF DEALING, TRADE USAGE OR
PRACTICE OR THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE OR NONINFRINGEMENT OF THIRD PARTY RIGHTS.
Limitation of Liability
IN NO EVENT SHALL AVER BE LIABLE FOR INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
PUNITIVE, OR CONSEQUENTIAL DAMAGES OF ANY NATURE INCLUDING, BUT NOT LIMITED
TO, LOSS OF PROFITS, DATA, REVENUE, PRODUCTION, OR USE, BUSINESS INTERRUPTION,
OR PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES ARISING OUT OF OR IN
CONNECTION WITH THIS LIMITED WARRANTY, OR THE USE OR PERFORMANCE OF ANY
PRODUCT, WHETHER BASED ON CONTRACT OR TORT, INCLUDING NEGLIGENCE, OR ANY
OTHER LEGAL THEORY, EVEN IF AVER HAS ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
AVER’S TOTAL, AGGREGATE LIABILITY FOR DAMAGES OF ANY NATURE,
REGARDLESS OF FORM OF ACTION, SHALL IN NO EVENT EXCEED THE AMOUNT PAID BY
YOU TO AVER FOR THE SPECIFIC PRODUCT UPON WHICH LIABILITY IS BASED.
46
Governing Law and Your Rights
This warranty gives you specific legal rights; You may also have other rights granted under state law.
These rights vary from state to state.
For warranty period, please refer to the warranty card.
47
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement