American Dynamics SpeedDome Ultra 8 camera dome User manual
Below you will find brief information for camera dome SpeedDome Ultra 8 SpeedDome Ultra 8. The SpeedDome Ultra 8 is a camera dome that can be used to set features for your camera dome using a text overlay menu. This menu is accessed via a keystroke combination on your camera controller. The utility provides settings relating to camera functions, alarms, text display, privacy zones, direction indicators, and password protection.
advertisement
▼
Scroll to page 2
of
12
Note: If Password Protection is enabled, the Enter Password screen (Screen 7) appears first. SpeedDome Ultra 8 Camera Dome Configuration Utility ® Choose an option on this screen to change settings. Table 1 describes the available commands. IMPORTANT: Commands may differ depending on your operating environment. These commands apply to SensorNet, RS-422, and Manchester. Quick Reference Guide If you need assistance… Table 1. SensorNet, RS-422, and Manchester commands Contact your Sales or Technical Support Representative. What is the Dome Configuration Utility? The Dome Configuration Utility is used to set features for your camera dome using a text overlay menu. This menu is accessed via a keystroke combination on your camera controller. The utility provides settings relating to camera functions, alarms, text display, privacy zones, direction indicators, and password protection. Some items supplement similar features that may be available through your controller or switching system. To start the utility: 1. Select a dome that you need to configure. Refer to your controller operating instructions for specific information. 2. Do one of the following: − If you want to... Use... Move the Highlight Bar. Pan/Tilt Select the highlighted item. Focus Increase value of selected setting, or display next choice. Move cursor to right during naming. Zoom In (Zoom Tele) Decrease value of selected setting, or display previous choice. Move cursor to left during naming. Zoom Out (Zoom Wide) Save changes and exit from any screen. Iris Close, then Focus Pan, Tilt, Zoom and Synchronization Options If the dome is installed in a SensorNet or RS-422 network, press and hold Iris Open, press and hold a Focus button, and then press Zoom Out (Zoom Wide). 2 − If the dome is installed in a Manchester network, turn the key switch to Prog, enter 66, and then press Set Preset (Set Shot). 3. The Dome Configuration Menu appears. 1 DOME CONFIGURATION MENU PAN/TILT/ZOOM/SYNC OPTS CAMERA FUNCTIONS ALARMS/AREAS/HOME/PRESETS/PZ ON-SCREEN TEXT DISPLAY LANGUAGE / PASSWORD DOME INFORMATION RESET TO FACTORY SETTINGS QUIT WITHOUT SAVING EXIT AND SAVE CHANGES Screen 2 3 4 5 • 6 8 • • • • • © 2009 Sensormatic Electronics Corp. SPEEDDOME ULTRA 8 CAMERA DOME CONFIGURATION UTILITY QUICK REFERENCE GUIDE PAN/TILT/ZOOM/SYNC OPTS PROPORTIONAL FLIP 1ST ZOOM STOP X MAX TOTAL ZOOM X LINE LOCK FREEZE FRAME RETURN TO AUTO OFF 35 420 OFF OFF RESET TO FACTORY SETTINGS EXIT The default 1st Zoom Stop setting is 52X for 35X camera domes and 33X for 22X camera domes. The default Max Total Zoom setting is 140X for 35X camera domes and 88X for 22X camera domes. Maximum total zoom settings: Vary depending on the initial zoom position. The default Line Lock setting is OFF. The default Freeze Frame setting is OFF. For Return to Auto settings, go to Return to Auto Settings (Screen 2.1). 8200-0600-02, REV. C 1 of 12 Some settings appear only when the associated setting is active. Use Table 2 and Table 3 to identify which settings apply. Return to Auto Settings 35X Camera Dome 2.1 22X Camera Dome RETURN TO AUTO CAMERA FUNCTIONS FOCUS IRIS CAMERA FUNCTIONS ON ON ON Auto White Bal AGC/Shutter Max Gain Open Shutter 26 dB RESET TO FACTORY SETTINGS EXIT • • • Limit 1/3 s RESET TO FACTORY SETTINGS EXIT The default Focus setting is ON. The default Iris setting is ON. The default Camera Functions setting is ON. Camera features include WDR, EIS, and IR Mode. The 22X camera dome does not support the IR Mode, WDR, and EIS features. Auto White Balance and Red/Blue Values 22X Camera Dome RETURN TO AUTO FOCUS IRIS ON The Auto White Bal setting determines if the Red and Blue values can be changed. ON ON Table 2. Auto White Balance settings Auto White Bal RESET TO FACTORY SETTINGS EXIT The 22X camera dome does not support the EIS, WDR, and IR Mode features. ON N/A N/A OFF Yes Yes The AGC/Shutter setting determines if the Max Gain and Limit settings apply. Note: Table 3 applies to both the 35X and 22X camera dome. 35X Camera Dome CAMERA FUNCTIONS Auto White Bal Blue AGC/Shutter Settings Camera Functions 3 Red Table 3. AGC/Shutter settings ON IR MODE/nM Auto Mid /Visible WDR OFF AGC/Shutter Max Gain Limit Open Shutter 26 dB 1/3 s EIS OFF RESET TO FACTORY SETTINGS EXIT SPEEDDOME ULTRA 8 CAMERA DOME CONFIGURATION UTILITY QUICK REFERENCE GUIDE AGC/Shutter Max Gain Limit Open Shutter Yes Yes AGC ON Yes N/A AGC OFF N/A N/A 8200-0600-02, REV. C 2 of 12 Alarms, Areas, Home, Presets and Privacy Zones 4 Set Alarm States 4.2 ALARMS/AREAS/HOME/PRESETS/PZ SET ALARM STATES INTERNAL ALARMS INPUT NORMAL STATE 1 2 3 4 SET ALARM ACTIONS SET ALARM STATES SET HOME POSITION SET NORTH POSITION AREA BOUNDARIES PRIVACY ZONES PRESETS SCAN LIMITS EXIT OPEN OPEN OPEN OPEN EXIT • Open is the default setting for all inputs. This screen provides links to lower level screens. See the following screens: • • • • • • • • Set Home Position Set Alarm Actions (Screen 4.1) Set Alarm States (Screen 4.2) Set Home Position (Screen 4.3) Set North Position (Screen 4.4) Area Boundaries (Screen 4.5) Privacy Zones (Screen 4.6) Presets: Select Preset to Program (Screen 4.7) Scan Limits (Screen 4.8) 4.3 SET HOME POSITION ACTION PRESET RETURN TIME MINS 1 10 EXIT Set Alarm Actions 4.1 • SET ALARM ACTIONS INPUT 1 2 3 4 NO NO NO NO ACTION ACTION ACTION ACTION ACTION • SEND INPUTS TO HOST? YES No Action is the default setting for the home position. Preset 1-96 or Pattern 1-3 may be assigned to the home position. Other actions are Output, Sequence, Smooth Scan, Stepped Scan, or Random Scan. Set North Position EXIT 4.4 • SET NORTH POSITION PAN to new north position No Action is the default setting for all inputs. Preset 1-96 or Pattern 1-16 may be assigned as the alarm action. ZOOM to mark north position FOCUS quits w/o changing • SPEEDDOME ULTRA 8 CAMERA DOME CONFIGURATION UTILITY QUICK REFERENCE GUIDE The default North Position is 0-degrees Pan/Tilt. 8200-0600-02, REV. C 3 of 12 • • Area Boundaries 4.5 AREA BOUNDARIES • PAN to START OF BOUND 1 • PAN RIGHT ONLY ZOOM to mark BOUNDARY FOCUS quits w/o changing Up to 8 Privacy Zones may be programmed. Three points must be selected to establish the Privacy Zone. The fourth point is automatically calculated. Use the Pan/Tilt control to position the arrows over the selection point. If arrows blink, this is not a valid selection area. Press Zoom to save the point. Delete Privacy Zone 4.6b Up to 16 areas may be programmed. These areas are separate from areas that may be available through your switcher. Navigate Privacy Zones 4.6 to zone ZOOM to delete zone FOCUS quits w/o changing PRIVACY ZONES ADD PRIVACY ZONE DELETE SPECIFIC ZONES DELETE ALL ZONES • • HIDE ALL ZONES NO • Arrows must be clearly positioned in zone to delete. Use the Pan/Tilt control to position the arrows over the zone. If arrows blink, this is not a valid selection area. Press Zoom to delete the selected zone. EXIT Delete All Zones In addition to hiding all programmed privacy zones, this screen provides links to lower level screens. See the following screens: • • • 4.6c Add Privacy Zones (Screen 4.6a) Delete Privacy Zone (Screen 4.6b) Delete All Zones (Screen 4.6c) YOU ARE ABOUT TO DELETE ALL PRIVACY ZONES CANCEL CONTINUE Add Privacy Zones 4.6a This option permanently removes all programmed Privacy Zones. To temporarily hide the zones, use Hide All Zones. See Privacy Zones (Screen 4.6). NEW PRIVACY ZONE Navigate corner 1 ZOOM to mark corner FOCUS to abandon zone SPEEDDOME ULTRA 8 CAMERA DOME CONFIGURATION UTILITY QUICK REFERENCE GUIDE 8200-0600-02, REV. C 4 of 12 Select Preset to Program 4.7 Motion Detection Setup Sub-Menu SELECT PRESET TO PROGRAM PRESET NUMBER 1 Active zone position programming screen 35X Camera Dome Only PRESET NAME PRESET 1 4.7b MOTION DETECTION SETUP SEQUENCE SETUP MENU CAMERA FUNCTIONS FOCUS FAR to program preset EXIT MOTION DETECTION SETUP ZONE 1 Zone Indicator The number of presets available depends on your operating environment. • ESC/FOCUS=save+exit If installed under SensorNet or RS-422, up to 96 presets are available. Use the joystick to move the rectangular zone indicator to a desired location, and then press Focus Far to save and exit. • If installed under Manchester, up to 64 presets are available. This screen provides links to lower-level screens. See the following screens: • Motion Detection Setup (Screen 4.7a) • • • • Sequence Setup Menu (Screen 4.7c) Program Presets (Screen 4.7d) Camera Functions (Screen 3) The 22X camera dome does not support the Sequence Setup features. Sequence Setup Menu 4.7c Motion Detection Setup 4.7a 35X Camera Dome Only 35X Camera Dome Only SEQUENCE SETUP MENU SEQUENCE NUMBER 1 STEP 1-4 DWELL TIME STEP PRESET MIN / SEC 1 0 0 0 2 0 0 0 3 0 0 0 4 0 0 0 EXIT MOTION DETECTION SETUP 1 ZONE 1 SENS 0 Use this screen to create preset sequences. ACTION NO ACTION HIDE ALL ZONES NO DELETE ALL ZONES UPDATE SENS AND ACTION FOCUS FAR to prog zone EXIT Program Presets 4.7d PRESETS Position camera with PAN, TILT, ZOOM and IRIS Use this screen to create detection zones (1-8) IMPORTANT: Motion Detection will not function under certain Camera Functions settings. Before programming, ensure the following: FOCUS FAR to save and exit EXIT • IR Mode is not set to ON • WDR is not set to ON. Press Focus Far to display the Motion Detection Setup Sub-Menu (Screen 4.7b) This screen also appears if a Preset is selected for the Set Home Position (Screen 4.3) and the selected preset has not been programmed. SPEEDDOME ULTRA 8 CAMERA DOME CONFIGURATION UTILITY QUICK REFERENCE GUIDE 8200-0600-02, REV. C 5 of 12 In addition to the settings available, this screen provides links to lower level screens. See the following: Scan Limits 4.8 • • SCAN LIMITS Name Configuration Menu (Screen 5.1) Text Attribute Options (Screen 5.2) PAN to LEFT limit Name Configuration Menu 5.1 ZOOM to mark BOUNDARY Cancel RIGHT limit to Delete CANCEL SCAN LIMITS CAMERA NAME AREA NAME PRESET NAME PATTERN NAME ALARM NAME OFF OFF OFF OFF ON FOCUS FAR to program names RESET PROGRAMMABLE NAMES EXIT PAN right to RIGHT limit • • ZOOM to mark BOUNDARY Cancel RIGHT limit to Delete CANCEL • Scan Limits are used to set right and left areas of surveillance with compatible controllers. These scans may be activated using the DirectSet Menu (Screen 10). Use Zoom to change the display setting. Press Focus to start name programming for highlighted setting. If Camera is selected, Name Programming (Screen 5.1a) automatically appears. For others, Select Name to Program (Screen 5.1b) appears. Name Programming • • • • Use Pan/Tilt to adjust the dome’s pointing direction. Press Zoom to select the left and right scan limits. Press Focus to cancel changes. Press Focus when setting right scan limit to delete the scan limits. Note: While you can use Smooth, Stepped, and Random scans without setting the scan limits, programming the left and right scan limits enables you to more effectively use these scan capabilities. 5.1a NAME PROGRAMMING NAME: ALARM 1 ABCDEFGHIJKLMNOPQRST UVWXYZabcdefghijklmn opqrstuvwxyz 0123456 789/UNDO CHANGES AND QUIT EXIT On-Screen Text Display 5 NAME CONFIGURATION MENU • • ON-SCREEN TEXT DISPLAY STATUS DISPLAY ON DISABLE ALL NAMES? NO DIAGNOSTICS DISPLAY ON DIRECTION INDICATOR ON PATTERN SELECT OFF NAME CONFIGURATION MENU TEXT ATTRIBUTE OPTIONS • Names may contain up to 18 characters. Use Pan/Tilt to move the highlight around available characters. Press Focus to select highlighted character. Zoom In moves the highlight one space right in the name; Zoom Out moves the highlight left. EXIT SPEEDDOME ULTRA 8 CAMERA DOME CONFIGURATION UTILITY QUICK REFERENCE GUIDE 8200-0600-02, REV. C 6 of 12 Select Name to Program 5.1b Language Selection 6.1 SELECT NAME TO PROGRAM NUMBER 1 LANGUAGE SELECTION ENGLISH SPANISH FRENCH GERMAN ITALIAN PORTUGUESE CURRENT NAME FOCUS FAR to program names EXIT • • EXIT Use Zoom to select the appropriate Alarm, Area, Pattern, or Preset number. Press Focus to start name programming. • • Dome must reset for language setting to change. Programmed names do not change after setting the language. Only the default names change. Text Attribute Options Set Password 5.2 6.2 TEXT ATTRIBUTE OPTIONS CHARACTER OUTLINE TRANSLUCENT NAMES ON 4 SET PASSWORD PASSWORD: ******** ABCDEFGHIJKLMNOPQRST UVWXYZabcdefghijklmn opqrstuvwxyz 0123456 789/CONTINUE CANCEL EXIT If Privacy Zones are displayed, Translucent Names is automatically disabled. • • Language and Password 6 Passwords may contain up to 8 characters. See Name Programming (Screen 5.1a) for instructions on how to set passwords. Enter Password LANGUAGE / PASSWORD 7 LANGUAGE SELECTION SET PASSWORD PASSWORD PROTECTION OFF ENTER PASSWORD PASSWORD: ******** ABCDEFGHIJKLMNOPQRST UVWXYZabcdefghijklmn opqrstuvwxyz 0123456 789/- EXIT CONTINUE CANCEL In addition to enabling password protection, this screen provides links to lower level screens. See the following screens: • Language Selection (Screen 6.1) • Set Password (Screen 6.2) This screen only appears when Password Protection is enabled. The password must be successfully entered before the Dome Configuration Menu will appear. SPEEDDOME ULTRA 8 CAMERA DOME CONFIGURATION UTILITY QUICK REFERENCE GUIDE 8200-0600-02, REV. C 7 of 12 • See Name Programming (Screen 5.1a) for instructions on how to enter passwords. • Dome Information 8 • Camera domes with Outdoor IO boards To configure a camera attached to a legacy IO board for either indoor or outdoor operation, select IO Configuration (Screen 8.5). IO board status information, select Base IO Status (Screen 8.6 for outdoor domes only). IO board control information, select Base IO Control (Screen 8.7 for outdoor domes only). DOME INFORMATION Dome Model DOME MODEL DOME STATISTICS INIT DOME CALIBRATION BASE IO STATUS BASE IO CONTROL 8.1 EXIT Camera domes with Indoor IO boards DOME MODEL NAME: ADSDU835D Mnemonic SDU8 Software Ver 0101-0150-0214 FPGA Ver 2006/10/31 15:58 Device Type 0150 Camera: 2003-0054-01 NTSC SN 00000000001234567890 Manufacture Date 01212003 EXIT DOME INFORMATION DOME MODEL DOME STATISTICS INIT DOME CALIBRATION This screen displays the dome model information. Dome Statistics EXIT 8.2 Camera domes with legacy IO boards DOME INFORMATION DOME MODEL DOME STATISTICS INIT DOME IO CONFIGURATION DOME STATISTICS PanStat TiltStat ZoomStat R 000000D0 00000074 0000006C L 000005E5 00000A5C 00000092 M 0000D8E9 00000F8A 0000019A T 0000051E 0000050A 00000002 001 SENSORNET Pwr/Run Pwr/Run O 002D389 W 00000000 P 0000002 U 00000000 EXIT This screen displays operating statistics for the dome. The information displayed represents the number of occurrences or time in seconds (displayed in hexadecimal format). EXIT • • • • • • • • This screen provides links to lower level dome information screens. The choices are: • Dome model information, select Dome Model (Screen 8.1 for all domes). • Dome usage information, select Dome Statistics (Screen 8.2 for all domes). • To clear dome user memory, select Init Dome (Screen 8.3 for all domes). When used with a legacy I/O board, Init Dome only clears memory in the dome. • To calibrate domes when replacing or installing new domes, select Calibration (Screen 8.4 for outdoor and indoor domes). SPEEDDOME ULTRA 8 CAMERA DOME CONFIGURATION UTILITY QUICK REFERENCE GUIDE R represents time moving Right in seconds. L represents time moving Left in seconds. M represents Total Move Time in seconds. T represents Target Count. O represents Operating Time in seconds. P represents Power Failure Reset Count. W represents Watchdog Reset Count. U represents User Reset Count. 8200-0600-02, REV. C 8 of 12 Note: The Calibration feature is applicable to the Outdoor Housing board, P/N 0312-2124-03, and the Indoor Housing board, P/N 0312-3006-01. Init Dome 8.3 Position Cross-hair To Target 1 Press Focus Far To Calibrate + INIT DOME NO This screen allows you to clear the dome and the • associated I/O flash in the dome base of all user-programmed options and returns the dome to factory defaults. The following screen appears during the initialization process. • Calibration is used only when replacing a dome in an existing base. The plus (+) sign in the middle of the screen is the crosshair used for calibration. IO Configuration Init Dome! 8.5 Initializing Please Wait IO CONFIGURATION CONFIGURATION INDOOR EXIT Calibration 8.4 This screen allows you to configure cameras attached to a legacy IO board for either indoor or outdoor operation. • Indoor operation does not use dome heaters or blowers. • Outdoor operation uses dome heaters and blowers. You must set this screen to Outdoor for the heaters and blowers to work. CALIBRATION PASSWORD: 0123456789 EXIT • This screen allows you to enter a password (135246) to access the calibration screen shown below, which enables you to define a zero reference point (or target) from which all other camera targets will be referenced. SPEEDDOME ULTRA 8 CAMERA DOME CONFIGURATION UTILITY QUICK REFERENCE GUIDE 8200-0600-02, REV. C 9 of 12 Base IO Status 8.6 Dome Address Change BASE IO STATUS BASE App Version: 2.30 BASE Boot Version 2.22 Temp: 40.1 C Humidity: 37 % Blower 1: ON Blower 2: ON Alarm Bits: 00 9 DOME ADDRESS CHANGED!! UPDATE DOME DATA FROM BASE CLEAR BASE DATA EXIT • This screen displays the base IO operating conditions and status. • The status information is automatically updated as it changes. Note: The Base IO Status feature is only applicable to the Outdoor Housing board, P/N 0312-2124-03. Base IO Control 8.7 BASE IO CONTROL Update App: v2.30 => v2.30 Blower Control: AUTO ON Heater Control: AUTO OFF EXIT When a dome powers up, it finds Pan/Tilt home, determines the network type, and then performs the following sequential tests: • Checks if its own address has changed. • Checks if its address matches the base IO address. If it does not, the Dome Address Changed screen appears to allow a change to be made. • Verifies that its configuration data matches the configuration data stored in the base IO. Note: Normally, you highlight Clear Base Data and press Focus Far from the keyboard. Invoking Clear Base Data clears all configuration data in the base IO. The other option, Update Dome Data From Base, should only be used when swapping identical dome models. The screen shown below briefly appears during: • The updating process. • Verification when dome configuration data does not match configuration data stored in the base IO memory and indicates the dome is copying the IO base configuration data. • This screen displays the base IO firmware version, enables updating of the firmware, and enables blower and heater control. Notes: Each time you upload new code to the dome, be sure to update the IO base as well. If the number to the left of the arrow is lower than the number to the right, highlight this line to start the firmware upgrade. The Base IO Control feature is only applicable to the Outdoor Housing board, P/N 0312-2124-03. Restoring Dome Data Names Buffer TPB Buffer The following screen briefly appears when base data is cleared. When base data is cleared, all presets, patterns, and other configurations stored in the base IO memory are deleted. SPEEDDOME ULTRA 8 CAMERA DOME CONFIGURATION UTILITY QUICK REFERENCE GUIDE 8200-0600-02, REV. C 10 of 12 DirectSet Menu Screen 3 of 4 49 50 51 52 53 54 55 56 57 Use Updating IO Base Memory! Please Wait! Note: After verification is complete, the last screen that was displayed before the dome was powered down will reappear. DirectSet Menu Screen 4 of 4 58 SEQUENCE 8 59 SEQUENCE 9 60 SEQUENCE 10 61 SEQUENCE 11 62 SEQUENCE 12 63 SEQUENCE 13 64 SEQUENCE 14 65 SEQUENCE 15 66 SEQUENCE 16 FOCUS NEAR=previous page DirectSet Menu 10 35X Camera Dome DirectSet Menu Screen 1 of 4 0 TOGGLE DIRECT SET MENU 1 DOME CONFIGURATION MENU 2 AUTO IRIS & AUTO FOCUS 3 FLIP 4 PEEL PATTERN 5 SET NORTH POSITION 6 LINE LOCK OFF 7 LINE LOCK ON 10 NIGHT MODE FOCUS FAR=next page 22X Camera Dome DirectSet Menu Screen 1 of 4 0 TOGGLE DIRECT SET MENU 1 DOME CONFIG MENU 2 AUTO IRIS & AUTO FOCUS 3 FLIP 4 PEEL PATTERN 5 SET NORTH POSITION 6 LINE LOCK OFF 7 LINE LOCK ON 15 SMOOTH SCAN FOCUS FAR=next page DirectSet Menu Screen 2 of 4 11 12 13 14 15 16 17 20 48 Use EIS 5 Hz EIS 10 Hz SEQUENCE 1 SEQUENCE 2 SEQUENCE 3 SEQUENCE 4 SEQUENCE 5 SEQUENCE 6 SEQUENCE 7 FOCUS to select page DAY MODE AUTO DAY/NIGHT MODE WDR ON WDR OFF SMOOTH SCAN STEPPED SCAN RANDOM SCAN DOME INFORMATION EIS OFF FOCUS to select page DirectSet Menu Screen 2 of 4 16 17 20 51 52 53 54 55 56 Use SPEEDDOME ULTRA 8 CAMERA DOME CONFIGURATION UTILITY QUICK REFERENCE GUIDE STEPPED SCAN RANDOM SCAN DOME INFORMATION SEQUENCE 1 SEQUENCE 2 SEQUENCE 3 SEQUENCE 4 SEQUENCE 5 SEQUENCE 6 FOCUS to select page 8200-0600-02, REV. C 11 of 12 DirectSet Menu Screen 3 of 4 57 58 59 60 61 62 63 64 65 Use SEQUENCE SEQUENCE SEQUENCE SEQUENCE SEQUENCE SEQUENCE SEQUENCE SEQUENCE SEQUENCE FOCUS to 7 8 9 10 11 12 13 14 15 select page DirectSet Menu Screen 4 of 4 66 SEQUENCE 16 The DirectSet Menu provides easy access to dome features and menus with compatible controllers. • Press the DirectSet or Info button (varies by controller) to display the menu. • Press Focus Far and Focus Near to scroll between the menu pages. • Enter a number and press the DirectSet button to activate the setting or menu. • Enter 0 and press the DirectSet button to close the menu. Refer to your controller instructions to determine if it is compatible with the DirectSet Menu function. WJM 04/2009 SPEEDDOME ULTRA 8 CAMERA DOME CONFIGURATION UTILITY QUICK REFERENCE GUIDE 8200-0600-02, REV. C 12 of 12
advertisement
Key Features
- Text overlay menu
- Camera functions
- Alarms
- Text display
- Privacy zones
- Direction indicators
- Password protection
Frequently Answers and Questions
How do I start the Dome Configuration Utility?
Select a dome that you need to configure. Refer to your controller operating instructions for specific information. If the dome is installed in a SensorNet or RS-422 network, press and hold Iris Open, press and hold a Focus button, and then press Zoom Out (Zoom Wide). If the dome is installed in a Manchester network, turn the key switch to Prog, enter 66, and then press Set Preset (Set Shot).
What does the DirectSet Menu do?
The DirectSet Menu provides easy access to dome features and menus with compatible controllers. Press the DirectSet or Info button (varies by controller) to display the menu. Press Focus Far and Focus Near to scroll between the menu pages. Enter a number and press the DirectSet button to activate the setting or menu. Enter 0 and press the DirectSet button to close the menu. Refer to your controller instructions to determine if it is compatible with the DirectSet Menu function.
How do I calibrate domes when replacing or installing new domes?
Select Calibration (Screen 8.4 for outdoor and indoor domes). You must enter a password (135246) to access the calibration screen, which enables you to define a zero reference point (or target) from which all other camera targets will be referenced.
Related manuals
Download
PDF
advertisement