msr series powered speakers
SPECIFICATIONS
MSR400
AMP SECTION
GENERAL
Output Power
Biamplified system
Type
Biamp. 2-way Powered Speaker
Crossover Frequency
1.6kHz
LF: 225W/ 4Ω
Overall Frequency Response
50Hz–20kHz
HF: 75W/16Ω
Maximum SPL
121dB (1m)
Dispersion
90° (H)/40° (V)
Input Sensitivity /Impedance
MIC/LINE: -36dB/+4dB 10kΩ
Dimension (W x H x D)
406 x 652 x 351 mm (16" x 25-3/4" x 13-7/8")
1: XLR-3-31 balanced
Weight
23kg (50.7lbs)
Input/Output Connectors
(all parallel)
Burst Power: 400W Total
2: XLR-3-32 balanced
3: PHONE balanced
SPEAKER SECTION
Components
Controls
LF: 12" cone
HF: 1.75" V.C. Compression Driver
Enclosure
Material
Optional Accessories
HIGH: (+/- 3dB at HF), POWER Switch (ON/OFF)
Indicators
Bass-reflex Type
PP
Power ON: Green LED
Clipping: Red LED
Power Requirment
BBS251 Baton Bracket
BCS251 Ceiling Bracket
LEVEL CONTROL, EQ. LOW: (+/- 3dB at 55Hz),
U/C: AC120V 60Hz, H/B: AC230V 50Hz, A: AC240V 50Hz,
K: AC220V 60Hz, CHN: AC220V 50Hz, TT: AC110V 60Hz
Power Consumption
110W
BWS251-400 Wall Bracket
MSR800W
GENERAL
AMP SECTION
Type
Powered Subwoofer
Overall Frequency Response
40–120 Hz
Maximum SPL
122 dB (1 m)
Input Sensitivity/Impedance
+4dB/30k Ω
Dimension (W x H x D)
600 x 521 x 590 mm (23-5/8" x 20-5/8" x 23-1/4")
Input Connectors
XLR balanced (A&B)
Weight
45kg (99.1lbs)
Output Sensitivity/Impedance
+4dB/150Ω
Output Connectors
Input (ch-A & B): XLR-3-31 (balanced)
Output Power
500W at 100Hz. THD =1%, RL = 8Ω
Burst Power: 800W
SPEAKER SECTION
THRU Out (ch-A & B): XLR-3-32 (balanced)
Components
15" cone
High Pass Out (ch-A & B): XLR-3-32 (balanced)
Enclosure
Bass-reflex Type
(100Hz, 18dB/oct, +4dB)
Material
Birch Plywood
Finish
Black Sprayed
Controls
MSR SERIES POWERED SPEAKERS
MASTER LEVEL CONTROL,
CUTOFF FREQ. Control: 80–100Hz (Variable),
PHASE Switch: (NORM/REV), POWER Switch: ON/OFF
Indicators
Power ON: Green LED, Clipping: Red LED
Power Requirment
U/C: AC120V 60Hz, H/B: AC230V 50Hz, A: AC240V 50Hz,
CHN: AC220V 50Hz
Power Consumption
200W
MSR100
POWERED SPEAKER
AMP SECTION
GENERAL
Type
2-way Powered Speaker
Output Power
100W at 1Hz. THD=1%, RL=6Ω
Crossover frequency
4kHz
Input Sensitivity
INPUT 1: -50dB/+4dB (with select SW)
Frequency Response
50Hz–20kHz (-10dB)
Maximum SPL
112dB (1m)
Input impedance
LINE 1 & 2 & 3: 10kΩ
Dispersion
90° (H)/40° (V)
Connectors
INPUT 1: XLR-3-31 (balanced)
Dimension (W x H x D)
275 x 455.5 x 255 mm (10-7/8" x 18" x 10-1/8")
Weight
11kg (24.2lbs)
SPEAKER SECTION
Components
INPUT 2 & 3: -10dB
INPUT 2 & 3: Phone (unbalanced)
LINK OUT: Phone (unbalanced)
Link Out
-10dB/10kΩ
Controls
Level Control INPUT 1 & 2 & 3, Master Level,
LF : 8"Cone
EQ LOW: ±3dB at 60Hz, HIGH: ±6dB at 10kHz
HF: 1"Compression Driver
Enclosure
Material
POWER Switch (ON/OFF)
Bass-reflex Type
Indicators
Power on: Green LED, Clip: Red LED
PP
Power Requirements
US & Canadian Models: AC120V 60Hz
European Models: AC230V 50Hz
Australian Models: AC240V 50Hz
POWERED SPEAKER
Compact in size but big in sound and versatile
features, the MSR100 packs a powerful sonic punch
— making it ideal for a wide range of applications in your stage setup.
Power Consumption
US & Canadian Models: 70W,
European Models: 70W, AT Models: 70W
Optional Accessories
BWS50-260/320 Wall Bracket
BWS251-300/-400 Wall Bracket
BCS251 Ceiling Bracket,
BBS251 Baton Bracket
• 0dB=0.775V
• Specifications and appearance subject to change without notice.
• All trademarks and registered trademarks are property of their respective owners.
www.yamahaproaudio.com
This document is printed on chlorine-free (ECF) paper with soy ink.
POWERED SUB WOOFER
LPA494
P10017040 Printed in Japan
POWERED SPEAKER
Great PA Sound Has Never Been Easier … Or Better Looking
Much of the work in putting together a high-performance sound system involves power amplifier and speaker
Bi-Amplification
selection and setup. Here’s a pair of solutions that can take you directly to great sound without the usual
The MSR400 is a bi-amplified 2-way system, featuring 400 watts maximum burst power that drives the
12" cone woofer and 1.75" V.C. compression driver. Frequency division is accomplished prior to the
power amplifiers via a line-level electronic crossover, eliminating the problems with loss, distortion,
and phase that are virtually unavoidable in conventional passive crossover networks. Another
advantage of this type of system is that power can be optimally assigned to the low-frequency and
high-frequency units for optimum efficiency as we all smooth, natural balance across the entire audio
spectrum.
complications. The MSR400 powered speaker can be used alone or in combination with the MSR800W powered
subwoofer to assemble sound reinforcement systems from modest to massive that will sound superb while delivering
the power and coverage you need for success in just about any venue or at any event. They look great, too. So good,
in fact, that they can be used as-is in many permanent installations without requiring any cosmetic cover-up. And, of
course, they’re more than rugged enough for demanding tour applications as well.
Wide Input Range & EQ Control
The Case For Built-in Power
Whether for use on the road or in permanent installations, powered speakers offer numerous advantages over their separate
counterparts. The most obvious is that you don’t need separate external amplifiers or the extra connections required – you can plug
your mixer’s outputs directly into the speaker inputs. In a modest-size system this alone can eliminate an entire rack of amplifiers. But
there are sonic advantages as well. Optimum matching of amplifiers and speakers involves much more than simple impedance figures,
and can be a formidable engineering task given the vast number of choices available. In the Yamaha MSR400 and MSR800W the
internal amplifiers have been ideally mated to their respective speakers in every way possible, delivering reproduction quality that
only such stringent matching can achieve.
The MSR400 accepts nominal input levels ranging from –36 dB to +4 dB,
meaning that you can directly connect any source from microphones to
professional line-level gear. Three parallel-connected connectors are
provided – two balanced XLR-type connectors and one balanced phone
jack – that can be used as either inputs or parallel outputs. The MSR400
also features an input level control for matching with the source signal.
Low and high EQ controls can be used to adjust the respective bands
over a plus-or-minus 3dB range.
Versatile Placement
Speaker placement is as much a performance issue as it is a convenience and aesthetic issue. Proper
placement will give you optimum sound as well as coverage while being as unobtrusive as possible.
Of course, the more options you have the better. The MSR400 can be
stacked or pole-mounted (there’s even a pole-mount hole provided on
the companion MSR800W Powered Woofer). And it’s flyable so you
can benefit from the unrivalled coverage and positioning precision
that only ceiling suspension can provide.
For Sound You Can Feel
SYSTEM EXAMPLE
The MSR800W powered subwoofer is the perfect companion for the MSR400, extending the low end and completing the musical
spectrum for maximum punch and impact. The high-quality birch plywood bass-reflex cabinet houses a 15” cone woofer powered by
an ultra-efficient burst 800 watts amplifier, a configuration that can deliver the elusive 40 Hz through 120 Hz frequency range with
precision and authority. Two balanced XLR connectors are provided for connection to the source, and that same signal can be directly
passed on to the main speakers via a pair of XLR “THRU” outputs. Alternatively, the main speakers can be fed by the MSR800W’s dual
“HIGH PASS” outputs, high-pass filtered at 80 Hz through100 Hz, depending on the setting of the cutoff frequency control, with a
steep 18 dB/octave cutoff slope.
MG24/14FX
In this system, the main house speakers are a pair of
MSR400s with speaker stands and MSR800W
subwoofer, driven directly from the mixer’s main
stereo and mono outputs. The MSR400s feature
punchy bass and exceptionally clear midrange that
delivers vocals with outstanding quality. The
MSR800W subwoofer takes care of the ultra-lows so
the audience hears – and feels – the full impact of the
music. A second pair of MSR400s is used for stage
monitoring, connected via a graphic equalizer for
feedback control.
ST OUT L
R
MONO
AUX1
AUX2
Q2031B
MSR400
MSR400
Visual Clip Indication
MSR800W
MSR400
MSR400
Both the MSR400 and MSR800W feature LED power indicators as well as clip indicators that warn of impending clipping, allowing the engineer to
make appropriate adjustments to the source level.
Great PA Sound Has Never Been Easier … Or Better Looking
Much of the work in putting together a high-performance sound system involves power amplifier and speaker
Bi-Amplification
selection and setup. Here’s a pair of solutions that can take you directly to great sound without the usual
The MSR400 is a bi-amplified 2-way system, featuring 400 watts maximum burst power that drives the
12" cone woofer and 1.75" V.C. compression driver. Frequency division is accomplished prior to the
power amplifiers via a line-level electronic crossover, eliminating the problems with loss, distortion,
and phase that are virtually unavoidable in conventional passive crossover networks. Another
advantage of this type of system is that power can be optimally assigned to the low-frequency and
high-frequency units for optimum efficiency as we all smooth, natural balance across the entire audio
spectrum.
complications. The MSR400 powered speaker can be used alone or in combination with the MSR800W powered
subwoofer to assemble sound reinforcement systems from modest to massive that will sound superb while delivering
the power and coverage you need for success in just about any venue or at any event. They look great, too. So good,
in fact, that they can be used as-is in many permanent installations without requiring any cosmetic cover-up. And, of
course, they’re more than rugged enough for demanding tour applications as well.
Wide Input Range & EQ Control
The Case For Built-in Power
Whether for use on the road or in permanent installations, powered speakers offer numerous advantages over their separate
counterparts. The most obvious is that you don’t need separate external amplifiers or the extra connections required – you can plug
your mixer’s outputs directly into the speaker inputs. In a modest-size system this alone can eliminate an entire rack of amplifiers. But
there are sonic advantages as well. Optimum matching of amplifiers and speakers involves much more than simple impedance figures,
and can be a formidable engineering task given the vast number of choices available. In the Yamaha MSR400 and MSR800W the
internal amplifiers have been ideally mated to their respective speakers in every way possible, delivering reproduction quality that
only such stringent matching can achieve.
The MSR400 accepts nominal input levels ranging from –36 dB to +4 dB,
meaning that you can directly connect any source from microphones to
professional line-level gear. Three parallel-connected connectors are
provided – two balanced XLR-type connectors and one balanced phone
jack – that can be used as either inputs or parallel outputs. The MSR400
also features an input level control for matching with the source signal.
Low and high EQ controls can be used to adjust the respective bands
over a plus-or-minus 3dB range.
Versatile Placement
Speaker placement is as much a performance issue as it is a convenience and aesthetic issue. Proper
placement will give you optimum sound as well as coverage while being as unobtrusive as possible.
Of course, the more options you have the better. The MSR400 can be
stacked or pole-mounted (there’s even a pole-mount hole provided on
the companion MSR800W Powered Woofer). And it’s flyable so you
can benefit from the unrivalled coverage and positioning precision
that only ceiling suspension can provide.
For Sound You Can Feel
SYSTEM EXAMPLE
The MSR800W powered subwoofer is the perfect companion for the MSR400, extending the low end and completing the musical
spectrum for maximum punch and impact. The high-quality birch plywood bass-reflex cabinet houses a 15” cone woofer powered by
an ultra-efficient burst 800 watts amplifier, a configuration that can deliver the elusive 40 Hz through 120 Hz frequency range with
precision and authority. Two balanced XLR connectors are provided for connection to the source, and that same signal can be directly
passed on to the main speakers via a pair of XLR “THRU” outputs. Alternatively, the main speakers can be fed by the MSR800W’s dual
“HIGH PASS” outputs, high-pass filtered at 80 Hz through100 Hz, depending on the setting of the cutoff frequency control, with a
steep 18 dB/octave cutoff slope.
MG24/14FX
In this system, the main house speakers are a pair of
MSR400s with speaker stands and MSR800W
subwoofer, driven directly from the mixer’s main
stereo and mono outputs. The MSR400s feature
punchy bass and exceptionally clear midrange that
delivers vocals with outstanding quality. The
MSR800W subwoofer takes care of the ultra-lows so
the audience hears – and feels – the full impact of the
music. A second pair of MSR400s is used for stage
monitoring, connected via a graphic equalizer for
feedback control.
ST OUT L
R
MONO
AUX1
AUX2
Q2031B
MSR400
MSR400
Visual Clip Indication
MSR800W
MSR400
MSR400
Both the MSR400 and MSR800W feature LED power indicators as well as clip indicators that warn of impending clipping, allowing the engineer to
make appropriate adjustments to the source level.
SPECIFICATIONS
MSR400
AMP SECTION
GENERAL
Output Power
Biamplified system
Type
Biamp. 2-way Powered Speaker
Crossover Frequency
1.6kHz
LF: 225W/ 4Ω
Overall Frequency Response
50Hz–20kHz
HF: 75W/16Ω
Maximum SPL
121dB (1m)
Dispersion
90° (H)/40° (V)
Input Sensitivity /Impedance
MIC/LINE: -36dB/+4dB 10kΩ
Dimension (W x H x D)
406 x 652 x 351 mm (16" x 25-3/4" x 13-7/8")
1: XLR-3-31 balanced
Weight
23kg (50.7lbs)
Input/Output Connectors
(all parallel)
Burst Power: 400W Total
2: XLR-3-32 balanced
3: PHONE balanced
SPEAKER SECTION
Components
Controls
LF: 12" cone
HF: 1.75" V.C. Compression Driver
Enclosure
Material
Optional Accessories
HIGH: (+/- 3dB at HF), POWER Switch (ON/OFF)
Indicators
Bass-reflex Type
PP
Power ON: Green LED
Clipping: Red LED
Power Requirment
BBS251 Baton Bracket
BCS251 Ceiling Bracket
LEVEL CONTROL, EQ. LOW: (+/- 3dB at 55Hz),
U/C: AC120V 60Hz, H/B: AC230V 50Hz, A: AC240V 50Hz,
K: AC220V 60Hz, CHN: AC220V 50Hz, TT: AC110V 60Hz
Power Consumption
110W
BWS251-400 Wall Bracket
MSR800W
GENERAL
AMP SECTION
Type
Powered Subwoofer
Overall Frequency Response
40–120 Hz
Maximum SPL
122 dB (1 m)
Input Sensitivity/Impedance
+4dB/30k Ω
Dimension (W x H x D)
600 x 521 x 590 mm (23-5/8" x 20-5/8" x 23-1/4")
Input Connectors
XLR balanced (A&B)
Weight
45kg (99.1lbs)
Output Sensitivity/Impedance
+4dB/150Ω
Output Connectors
Input (ch-A & B): XLR-3-31 (balanced)
Output Power
500W at 100Hz. THD =1%, RL = 8Ω
Burst Power: 800W
SPEAKER SECTION
THRU Out (ch-A & B): XLR-3-32 (balanced)
Components
15" cone
High Pass Out (ch-A & B): XLR-3-32 (balanced)
Enclosure
Bass-reflex Type
(100Hz, 18dB/oct, +4dB)
Material
Birch Plywood
Finish
Black Sprayed
Controls
MSR SERIES POWERED SPEAKERS
MASTER LEVEL CONTROL,
CUTOFF FREQ. Control: 80–100Hz (Variable),
PHASE Switch: (NORM/REV), POWER Switch: ON/OFF
Indicators
Power ON: Green LED, Clipping: Red LED
Power Requirment
U/C: AC120V 60Hz, H/B: AC230V 50Hz, A: AC240V 50Hz,
CHN: AC220V 50Hz
Power Consumption
200W
MSR100
POWERED SPEAKER
AMP SECTION
GENERAL
Type
2-way Powered Speaker
Output Power
100W at 1Hz. THD=1%, RL=6Ω
Crossover frequency
4kHz
Input Sensitivity
INPUT 1: -50dB/+4dB (with select SW)
Frequency Response
50Hz–20kHz (-10dB)
Maximum SPL
112dB (1m)
Input impedance
LINE 1 & 2 & 3: 10kΩ
Dispersion
90° (H)/40° (V)
Connectors
INPUT 1: XLR-3-31 (balanced)
Dimension (W x H x D)
275 x 455.5 x 255 mm (10-7/8" x 18" x 10-1/8")
Weight
11kg (24.2lbs)
SPEAKER SECTION
Components
INPUT 2 & 3: -10dB
INPUT 2 & 3: Phone (unbalanced)
LINK OUT: Phone (unbalanced)
Link Out
-10dB/10kΩ
Controls
Level Control INPUT 1 & 2 & 3, Master Level,
LF : 8"Cone
EQ LOW: ±3dB at 60Hz, HIGH: ±6dB at 10kHz
HF: 1"Compression Driver
Enclosure
Material
POWER Switch (ON/OFF)
Bass-reflex Type
Indicators
Power on: Green LED, Clip: Red LED
PP
Power Requirements
US & Canadian Models: AC120V 60Hz
European Models: AC230V 50Hz
Australian Models: AC240V 50Hz
POWERED SPEAKER
Compact in size but big in sound and versatile
features, the MSR100 packs a powerful sonic punch
— making it ideal for a wide range of applications in your stage setup.
• 0dB=0.775V
• Specifications and appearance subject to change without notice.
• All trademarks and registered trademarks are property of their respective owners.
POWERED SUB WOOFER
Power Consumption
US & Canadian Models: 70W,
European Models: 70W, AT Models: 70W
Optional Accessories
BWS50-260/320 Wall Bracket
BWS251-300/-400 Wall Bracket
BCS251 Ceiling Bracket,
BBS251 Baton Bracket
POWERED SPEAKER
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement