sineax i538

Add to my manuals
4 Pages

advertisement

sineax i538 | Manualzz
SINEAX I 538
Transducer for AC current
With power supply
Carrying rail housing P8/35
Application
The transformer SINEAX I 538 (Fig. 1) converts a sinusoidal AC
current into a load independent DC current or a load independet
DC voltage proportional to the measured value.
The transducer fulfils all the important requirements and regulations
concerning electromagnetic compatibility EMC and Safety (IEC
1010 resp. EN 61 010). It was developed and is manufactured and
tested in strict accordance with the quality assurance standard
ISO 9001.
Fig. 1. Transducer SINEAX I 538 in housing P8/35
clipped onto a top-hat rail.
Features
Technical data
● Measuring input: AC current, sine wave forms
Measuring input E
Measured variable
Measuring range limits
AC current
0 … 0.8 to 0 … 1.2 A
or
0 … 4 to 0 … 6 A
Nominal frequency fN:
50 / 60 Hz
● Measuring output: Unipolar and live zero output variables
Nominal input current IN
(measuring range end value): Measuring range limit value
0 … 0.8 to 0 … 1.2 A or
0 … 4 to 0 … 6 A
● Also available with output signal 4…20 mA in 2-wire connection
Own consumption:
● Measuring principle: Rectifier method
● Standard as marine version per Lloyd’s Register of Shipping
≤ 5 mV · IN with input end value
Overload capacity:
Measured
quantity
IN
Number of
applications
1.2 · IN
20
· IN
Duration
of one
application
Interval between
two successive
applications
–––
continuously
–––
10
1s
100 s
Measuring output A
Load-independent
DC current:
0 … 1.0 to 0 … 20 mA
resp. live zero
0.2 … 1 to 4 … 20 mA
Burden voltage:
15 V
External resistance:
Rext max. [kΩ] ≤
15 V
IAN [mA]
IAN = Output current end value
Camille Bauer
Data sheet I 538 Le – 02.14
1
SINEAX I 538
Transducer for AC current
With 2-wire connection
Standard ranges 4 … 20 mA
External resistance Rext, dependent
on power supply H (12…32 V DC)
External
resistance [Ω]
1000
Protection class:
II (protection isolated, EN 61 010)
Housing protection:
IP 40, housing
(test wire, EN 60 529)
IP 20, terminals
(test finger, EN 60 529)
600
0
0
12
24
H = Power supply [V]
Rext max. [kΩ] =
Load-independent
DC voltage:
Safety
32
H [V] – 12 V
Rext min. [kΩ] ≥
Current limit
under overload:
< 30 mA
2
Overvoltage category:
III
Rated insulation voltage
(versus earth):
20 mA
0 … 1 to 0 … 10 V resp.
live-zero 0.2 … 1 to 2 … 10 V
External resistance:
Contamination level:
Test voltage:
≤ 1% p.p.
Setting time:
< 300 ms
UA [V]
3700 V, power supply AC versus
output as well as outer surface
10 mA
490 V, power supply 24 V DC versus
output as well as outer surface
490 V, output versus outer surface
Installation data
Power supply H
AC voltage:
230 V, ± 15%, 50 / 60 Hz
Power consumption approx. 3 VA
DC voltage:
24 V, – 15 / + 33%,
Power consumption
approx. 1.5 W
or
24 V, – 50 / + 33% at 2-wire connection and output 4…20 mA
DC or AC voltage:
DC, AC power pack
(DC or 40 - 400 Hz)
85 - 230 V or 24 - 60 V
DC – 15/+ 33%, AC ± 15%
Power consumption
≤ 1.5 W resp. ≤ 3 VA
Mechanical design:
Housing P8/35
Material of housing:
Lexan 940 (polycarbonate),
flammability Class V-0 acc. to UL 94,
self-extinguishing, non-dripping,
free of halogen
Mounting:
For rail mounting
Weight:
Approx. 280 g
with AC power supply
Approx. 210 g
with DC power supply
Approx. 125 g
with 2-wire connection
Approx. 220 g
with DC, AC power pack
Connecting terminals
Connection element:
Accuracy (acc. to EN 60 688)
Reference value:
Output end value
Accuracy:
Class 0.5
50 Hz, 1 min. acc. to EN 61 010-1
3700 V, input versus all other circuits
as well as outer surface
Voltage limit under Rext = ∞: < 40 V
Residual ripple in
output current:
300 V input
300 V power supply AC
50 V power supply 24 V DC
50 V output
Permissible cross section
of the connection leads:
Screw-type terminals with indirect
wire pressure
≤ 4.0 mm2 single wire or
2 × 2.5 mm2 fine wire
Reference conditions:
Ambient temperature
15 … 30 °C
Environmental conditions
Input frequency
50 Hz
Operating temperature:
– 10 to + 55 °C
Curve shape
Sine-wave,
Distortion factor < 1%
Storage temperature:
– 40 to + 70 °C
Output burden
Current: 0.5 · Rext max.
Voltage: 2 · Rext min.
Relative humidity of
annual mean:
≤ 75%
Power supply
in rated range
Altitude:
2000 m max.
Indoor use statement
2
Data sheet I 538 Le – 02.14
Camille Bauer
SINEAX I 538
Transducer for AC current
IEC 1000-4-2/-3/-4/-5/-6
EN 55 011:
Ambient tests
Electromagnetic compatibility
EN 60 068-2-6:
Vibration
Acceleration:
±2g
Germanischer Lloyd
Frequency range:
10 … 150 … 10 Hz, rate of frequency
sweep:
1 octave/minute
Type approval certificate:
No. 12 258-98 HH
Ambient category:
C
Vibration:
0.7 g
Number of cycles:
10, in each of the three axes
EN 60 068-2-27:
Shock
Acceleration:
3 × 50 g
3 shocks each in 6 directions
EN 60 068-2-1/-2/-3:
Cold, dry heat, damp heat
Specification and ordering information
*Blocking
code
Description
SINEAX I 538
Features, Selection
Order Code 538 - xxxx xxx
No-go with
Article No./
blocking code
Feature
538 –
1. Mechanical design
Housing P8/35 for rail mounting
4
2. Nominal input frequency
50 / 60 Hz
1
3. Measuring range
0…1A
A
0…5A
B
Non-standard 0 … 0.8 to 0 … 1.2 or 0 … 4 to 0 … 6
[A]
Z
4. Output signal
0 … 20 mA, Rext ≤ 750 Ω
A
1
4 … 20 mA, Rext ≤ 750 Ω
A
2
4 … 20 mA, 2-wire connection, Rext dependent on power supply
B
3
Non-standard 0 … 1 to 0 … < 20
0.2 … 1 to < (4 … 20)
A
9
A
A
A
Z
[mA]
0 … 10 V, Rext ≥ 1 kΩ
Non-standard 0 … 1.00 to 0 … < 10
0.2 … 1 to 2 … 10
[V]
5. Power supply
230 V, 50/60 Hz
C
B
5
24 V DC
C
B
A
24 V DC via output circuit at 2-wire connection
C
A
B
24 … 60 V DC, AC (DC, AC power pack)
B
C
85 … 230 V DC, AC (DC, AC power pack)
B
D
6. Measuring range adjustable
Measuring range end value permanently set (standard)
Measuring range can be adjusted approx. ± 10%
Only in combination with DC, AC power pack, feature 5, line C or D!
Camille Bauer
Data sheet I 538 Le – 02.14
0
C
1
3
SINEAX I 538
Transducer for AC current
*Blocking
code
Description
SINEAX I 538
Features, Selection
Order Code 538 - xxxx xxx
No-go with
Article No./
blocking code
Feature
538 –
7. Test certificate
Without test certificate
0
Test certificate in German
D
Test certificate in English
E
* Lines with “letter(s)” under «No-go” cannot be combined with preceding lines having the same letter under “Blocking code”.
Electrical connections
– +
H = 24V, – 50 / + 33%
– +
Rext
– +
–
Optionally with
potentiometer
for variable
sensibility ± 10%
+
5 6 7 8
5 6 7 8
5 6 7 8
5 6 7 8
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
–
– +
I
I
I
Fig. 2. SINEAX I 538 with
AC power supply.
Fig. 3. SINEAX I 538 with
DC power supply.
Fig. 4. SINEAX I 538-41.3 B..
as 2-wire transducer with
output 4 … 20 mA.
I
I
= Current measuring input
= Measuring output
= Power supply
Fig. 5. SINEAX I 538 with DC, AC
power supply, in version with
built-in DC, AC power pack.
Dimensional drawing
112.5
69.1
5 6 7 8
1 2 3 4
114.1
Rely on us.
35
Fig. 6. SINEAX I 538 in housing P8/35 clipped onto a top-hat rail
(35 ×15 mm or 35×7.5 mm, acc. to EN 50 022).
Subject to change without notice • Edition 02.14 • Data sheet I 538 Le
Camille Bauer AG
Aargauerstrasse 7
CH-5610 Wohlen / Switzerland
Phone: +41 56 618 21 11
Fax:
+41 56 618 21 21
[email protected]
www.camillebauer.com

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement