Naxa NPB-427 Instruction manual

Add to my manuals
9 Pages

advertisement

Naxa NPB-427 Instruction manual | Manualzz

IMPORTANT NOTES

INTRODUCTION

Thank you for buying our product.

Please read carefully throughout these operating instructions, so you will know how to operate your equipment properly. After you finished reading the instructions manual, put it away in a safe and handy place for future reference.

WARNING

To prevent fire or shock hazard, do not expose this appliance to rain or moisture. To avoid electrical shock, do not open the cabinet; refer servicing to qualified personnel only.

CAUTION

Use of controls or adjustment or performance of procedures other than those specified herein may result in hazardous radiation exposure.

DANGER

Invisible laser radiation when open and interlock failed or defeated. Avoid direct exposure to beam.

This Compact Disc player is classified as a Class 1 LASER

PRODUCT.

The CLASS 1 LASER PRODUCT label is located on the rear end exterior.

NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications made by the user while operating this equipment.

Avoid installing the unit in locations described below:

1. Places exposed to direct sunlight or close to heat radiating appliance such as electric heaters, on top of other stereo equipment that radiate too much heat

2. Places lacking of proper ventilation or dusty places

3. Places subject to constant vibration

4. Humid or moist places

Operate all unit controls, bottoms and switches as instructed in manual.

Before turning on the power for the first time, make sure that the power cord is properly installed

Store your tapes or CD in a cool area to avoid damage from heat.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO DOT REMOVE PLASTIC

UNIT COVER (OR BACK CABINET). THERE ARE NO USER SERVICEABLE

PARTS INSIDE, IF UNIT NEEDS SERVICE, PLEASE TAKE THIS UNIT TO

QUALIFIED SERVICE PERSONNEL ONLY

WARNING:

Remove batteries if they become exhausted or if you know that this unit will not be used again after a long period of time

The incorrect use of batteries can cause electrolyte leakage, which can corrode the battery compartment or cause the batteries to burst out, therefore:

- Do not mix battery types, e.g. alkaline with zinc carbonate.

- When inserting new batteries, replace all batteries at the same time.

1

2

FEATURES AND CONTROLS

1. SPEAKERS

2. CARRY HANDLE

3. CD COMPARTMENT

4. CASSETTE COMPARTMENT

5. CD SKIP FORWARD BUTTON

6. CD SKIP BACKWARD BUTTON

7. FUNCTION SWITCH

8. BUILT-IN CONDENSER MIC.

9. AUX IN JACK

10. FOLD-/-10 BUTTON

11. POWER BUTTON

12. DIAL SCALE

13. FM ROD ANTENNA

14. POWER INDICATOR

15. LCD DISPLAY

16. FM STEREO INDICATOR

POWER SOURCE

This unit is designed to be operated on AC/DC.

17. AC VOLTAGE SELECTOR

(FOR DUAL VOLTAGE VERSION)

18. FOLD+/+10 BUTTON

19. CD PROG./P-MODE BUTTON

20. BAND SELECTOR

21. TUNING CONTROL

22. VOLUME CONTROL

23. CD PLAY/PAUSE BUTTON

24. CD STOP BUTTON

25. CASSETTE FUNCTION KEYS

26. BATTERY COMPARTMENT

27. AC SOCKET

28. SPEAKER TERMINALS

29. REMOTE SENSOR

AC OPERATION

Plug the smaller end of AC power cord into AC jack on unit and the other bigger end into household AC wall outlet. The batteries will be automatically disconnected. For dual voltage version, make sure that the AC VOLTAGE SELECTOR is switched to your local voltage.

DC OPERATION

Open the BATTERY COMPARTMENT DOOR. Install 8 pcs UM-1/D size batteries (not included) into compartment. Please follow correct polarities as indicated.

CAUTION

Remove batteries if they are exhausted or long time use.

Batteries contain chemical substances, so they should be disposed of properly.

BASIC FUNCTION

SWITCHING ON THE UNIT

Set the FUNCTION switch to CD/MP3/AUX or RADIO, the POWER indicator will be on.

TO ADJUST VOLUME

Rotate the VOLUME CONTROL clockwise or anticlockwise to increase or decrease volume.

AUX IN OPERATION

This unit has provided special AUX-IN jack, through this jack other audio sources can be connected to this unit and be amplified.

1. Set the FUNCTION switch to CD/MP3/AUX position.

2. Connect the audio cable into the AUX-IN jack and the other end connect to the AUDIO OUT jack of the external audio source. The unit will change to AUX mode automatically.

3. Adjust the volume of the main unit to your desired level.

Press PLAY of the external audio source (eg. MP3 player) to start playback.

3

LOADING THE BATTERIES INTO THE REMOTE HANDSET

 Open the battery compartment cover.

 Insert two “AAA” batteries (not included) as indicated inside the battery compartment.

 Close the cover.

KEY FUNCTIONS:

1. CD PLAY/PAUSE BUTTON

2. CD SKIP FORWARD BUTTON

3. CD STOP BUTTON

4. +10 MP3 BUTTON

5. CD SKIP BACKWARD BUTTON

6. -10 MP3 BUTTON

7. PROG./P-MODE BUTTON

8. BATTERY COMPARTMENT

REMOTE CONTROL OPERATION

To operate the unit with the remote control, point the remote handset at the remote sensor on the front panel and press the appropriate button on the remote handset.

The remote works best within a range of 6 ~ 7 meters from the front panel and on an angle of 30 degrees. Bright sunlight or room light conditions can interfere with the remote control. If the remote operation is unsatisfactory or stops working entirely, first try replacing the remote batteries, then try reducing the room lighting conditions.

USING THE RADIO

TUNING IN RADIO STATIONS

1. Move the FUNCTION switch to RADIO position, the POWER indicator will illuminate.

2. Slide the BAND switch to select the desired wave band: AM, FM, FM ST..

3. Tune to desired station by rotating the TUNING KNOB.

4. Adjust VOLUME CONTROL to desired volume level.

5. Extend TELESCOPIC ANTENNA to its full length if you are listening to FM broadcasting Gently rock the unit back and forth to get the best reception when you are listening to AM program, or place the unit in an open location.

Note: The FM STEREO indicator will be on when you are receiving FM stereo program.

6. Turn off the radio by switching the FUNCTION switch to "TAPE" position

USING THE CASSETTE

UNDERSTANDING THE BUTTONS

RECORD - Press to record from the radio or CD/MP3/AUX player.

PLAY - Press to play cassettes.

REWIND - From stop mode, press to rewind the tape toward the beginning.

F.FWD - From stop mode, press to advance the tape toward the end.

STOP/EJ. - Press to stop current tape activity or to open the cassette compartment door when no buttons are active.

PAUSE - Press to interrupt tape play or record mode. Press the second time to resume tape play or tape record mode.

4

PLAYING A CASSETTE TAPE

1. Slide the FUNCTION switch to TAPE position.

2. Press STOP/EJ. key to open the cassette compartment door.

3. Insert cassette tape into the compartment with the open edge facing up and the full reel on the right.

4. Close the door securely.

5. Press REWIND or F.FWD to move tape to the desired starting point.

6. Press PLAY key to begin playing the tape.

7. Adjust the volume to your desired listening level.

AUTOMATIC STOP FEATURE

When the cassette deck is operating in play or record mode and the end of the tape is reached, the unit automatically shuts itself off and returns all buttons to the off position.

RECORDING FROM THE RADIO

1. Load a blank tape into the tape compartment and close the door.

2. Set the FUNCTION switch to RADIO; Tune to required station by rotating the TUNING KNOB.

3. Press RECORD key to begin recording. The RECORD key and PLAY key go down simultaneously.

4. Press STOP/EJ. key to end recording.

5. To hear what you recorded, follow instructions in PLAYING A CASSETTE TAPE.

NOTE: PAUSE FOR A MOMENT - Using the PAUSE key on the cassette deck instead of the

STOP/EJ. key to momentarily interrupt recording gives you a much clear recording.

RADIO RECORDING TIPS

To temporarily pause the recording, press PAUSE key on the cassette deck. Press PAUSE key again to resume recording.

RECORDING FROM CD/MP3

1. Insert a blank cassette tape into the tape compartment.

2. Slide the FUNCTION switch to CD/MP3/AUX position.

3. Load a CD and select the desired track you want to record.

4. Press CD PLAY/PAUSE button to start playback. Press RECORD key to begin recording.

RECORD key and PLAY key go down simultaneously.

5. Press PAUSE key to interrupt or edit recording. Press it again to resume recording.

6. Press STOP/EJ. key to end recording.

7. To hear what you recorded, follow instructions in PLAYING A CASSETTE TAPE.

USING THE CD/MP3

Discs for Playback

This system can playback all digital audio CD, MP3 finalized digital audio CD-Recordable (CD-R) discs, finalized digital audio CD-Rewritable (CD-RW) discs and CD-DA format digital audio

CD/CD-R/CD-RW discs.

LOADING A DISC

1. Set the FUNCTION switch to CD/MP3/AUX position.

2. Open the CD door. “ OP ” will be shown on the display.

3. Place an audio CD/MP3 into the tray with the label side facing up.

4. Close the CD door. The total number of tracks and the disc type will appear on the display after several seconds.

5. To remove the CD, press CD door PUSH OPEN to open CD compartment lid, grasp the CD by its edges, and carefully take it out.

5

Note:

To ensure good system performance, wait until the disc tray completely reads the disc before proceeding.

If no disc loaded into the compartment, or the disc is place upside down or unreadable, the display will show nod.

PLAYING A DISC

Playing A Disc

1. Press the PLAY/PAUSE button to start playback, the playback starts from track 1, “ ” will appear on the display.

2. To interrupt playback, press the PLAY/PAUSE button, “ ” will flashing and the track number will steady on and off on the display.

3. To resume playback, press the PLAY/PAUSE button again.

4. To stop playback, press the STOP button, the total number of tracks appears on the display.

Selecting A Different Track During Play

1. Press CD SKIP FORWARD/BACKWARD button on the unit continuously until the desired track number appears in the display.

2. Playback starts from the desired track. (Press CD PLAY/PAUSE button to start playback in stop mode).

Starting Again With the Track That Is Currently Playing

1. Press CD SKIP BACKWARD button once.

2. The playback will start again from the beginning of the track.

Stopping Play

1. Press CD STOP button if you wish to stop play. The total track number which can be played will now appear on the display.

2. Open the CD door on the unit to remove the CD.

PROGRAM TRACKS

rogramming tracks of disc are possible when playback is stopped. Up to CD 20 tracks /MP3 99 tracks can be stored in the memory in any order.

1. In stop mode, press the PROG./P-MODE button, the PROG will flash and the P01 indicator will be on.

2. Press the CD SKIP/SEARCH FORWARD button to select the first desired track to be programmed.

3. Press the PROG./P-MODE button to enter. The display changes to show P02.

4. Repeat steps 2 & 3 to store other desired tracks until all tracks are programmed.

5. Press the PLAY/PAUSE button to start playback from the first programmed track.

6. Press the STOP button to stop program playback.

To Erase the Memory (Program)

To clear the program, you have two options:

1. Press the STOP button until “PROG” disappears on the display, or

2. Open the CD compartment lid, program will be erased.

REPEAT

You can play one track or all tracks on the disc repeatedly.

To Repeat a Single Track

1. Press the PROG./P-MODE button once in play, " " shows flashing on the display. The current track will be played over and over again till you press the STOP button.

2. To cancel repeat play, press PROG./P-MODE button till the " " disappears from display.

6

To repeat all the Tracks

1. Press PROG./P-MODE button till the " " shows steady on the display, all tracks on the disc will be played over and over again till you press the STOP button.

2. To cancel repeat play, press the PROG./P-MODE button till the " " disappears from the display.

To repeat current Directory (for MP3 only)

1. Press PROG./P-MODE button untill “ FOLD” shows steady on the display, The current directory will be played repeatedly until the STOP button is pressed.

2. Press the PROG./P-MODE button twice to cancel.

RANDOM PLAY

Press the PROG./P-MODE button in play mode till the “RDM ” shows steady on the display, the random play will start from next track automatically(or press CD skip forward button), until all tracks are played over and then stop. Press the PROG./P-MODE button once to cancel.

To select a song which track number exceeds 10

To select a song/track which number exceeds 10, Press the FOLD+/+10 or FOLD-/-10 button each time to skip forward/backward 10 tracks, then press the CD SKIP FORWARD/BACKWARD button to select desired track. For example: to select the 17 th track, press FOLD+/+10 button, and then the CD SKIP

FORWARD button six times immediately.

To Select A Desired Folderfor MP3 disc only

(if the MP3 disc contains more than one folder)

To skip to the desired folder during playback, press and hold the

FOLD+/+10 or FOLD-/-10 button for about 2 seconds to skip to next/previous folder.

7

SPECIFICATIONS

GENERAL

Power consumption

DC 12V UM-1 x 8 PCS

AC 20 Watts

Dimensions Approx. 455mm (W) x 220mm (H) x 245mm (D) temperature +5° °C

RADIO RECEPTION

AM KHz

FM 88 - 108 MHz

CD PLAYER

Optical Pickup 3-Beam Laser

CASSETTE & RECORDER

Biasing System DC bias

AUDIO

2.5 2

ACCESSORIES

Remote Sensor 1

CAUTION

To avoid electric shock, this unit must not be exposed to dripping water or liquid splash.

Ventilation warning - The normal ventilation of the product shall never be blocked - Avoid risk of fire

8

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement