Installation Instructions

Installation Instructions
Access Power Controllers
with Power Supplies
Installation Guide for models:
eFlow4NA8
eFlow6NA8
eFlow102NA8
eFlow104NA8
- 4A @ 12VDC or 24VDC - 6A @ 12VDC or 24VDC
- Eight (8) Fused Outputs - Eight (8) Fused Outputs
- 10A @ 12VDC - 10A @ 24VDC
- Eight (8) Fused Outputs - Eight (8) Fused Outputs
ULC-S319 - Electronic Access Control Systems will be invalidated through the use of any add-on, expansion,
memory or other module manufactured by the manufacturer or other manufacturers.
For a red enclosure add an “R” suffix to the part # e.g. eFlow4NA8R
Altronix Corp.
140 58th St. Brooklyn, NY
Rev. eACM052313
More than just power.™
Installing Company: ______________________ Service Rep. Name: ___________________________________________
Address: _________________________________________________________ Phone #: __________________________
Overview:
These units distribute and switch power to access control systems and accessories. They convert a 120VAC 60Hz input into eight (8)
independently controlled 12VDC or 24VDC fuse protected outputs. These power outputs can be converted to dry form “C” contacts.
Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader,
Keypad, Push Button, PIR, etc. Units will route power to a variety of access control hardware devices including: Mag Locks, Electric
Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. The FACP Interface enables
Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the eight (8) outputs.
eFlow ACM Series Configuration Reference Chart:
ACM8 Board
Output Fuse Rating
ACM8 Board
Input Fuse Rating
Power Supply Board
Battery Fuse Rating
Power Supply Board
Input Fuse Rating
Fuse Protected
Outputs
120VAC 60 Hz
Input (current)
Current per ACM8
output (A)
24VDC Output
Range (V)
12VDC Output
Range (V)
[AUX]
24VDC Output
Range (V)
12VDC Output
Range (V)
[DC]
Maximum Supply
Current for
Main and
Aux. Outputs (A)
Nominal DC Output Voltage Options
Altronix
Model
Number
eFlow4NA8
10.1-13.2 20.28-26.4 10.05-13.2 20.2-26.4
3.3A
3.6A
8
3.5A 2.5A 5A/250V 7.5A/32V 10A/250V 2.5A/250V
eFlow6NA8
10.0-13.2 20.19-26.4 10.03-13.2 20.19-26.4
5.3A
5.6A
8
3.5A 2.5A 5A/250V
10A/32V 10A/250V 2.5A/250V
15A/32V 10A/250V 2.5A/250V
eFlow102NA8 10.03-13.2
eFlow104NA8
----------
12VDC 24VDC
----------
10.03-13.2
----------
9.3A
----------
8
3.5A 2.5A 5A/250V
20.17-26.4
----------
20.17-26.4
----------
9.6A
8
4.5A 2.5A 6.3A/250V 15A/32V 10A/250V 2.5A/250V
*eFlow4NA8 only: This unit is classified as Power-Limited stand alone power supply with stand-by battery and it is suitable
to power: sensors, electro-mechanical devices (e.g. electric door strikes).
*eFlow6NA8, eFlow102NA8, and eFlow104NA8: The DC output for these power supplies are not power-limited. If a power-limited
output is required in the end-product application, the DC output from the power supply must be connected to a separately Listed control
unit or accessory board that provides power-limited outputs. The product(s) providing the power-limited output(s) must be listed as appropriate for the particular end-product application (access control), and wired in accordance with the products installation instructions.
Class 1 wiring methods, separation of circuits, and proper fire-rated enclosures all must be considered when connecting the DC output
of the power supply to the end-product devices. The auxiliary outputs of these units are power-limited.
* UL Listings for US Installations: UL 294 - UL Listed for Access Control System Units.
UL Listings for Canadian Installations: ULC-S319-05 - Electronic Access Control Systems. Class I Equipment;
CSA C22.2 No.205 - Signal Equipment.
ACM8 Access Power Controller Module:
Specifications:
• Eight (8) independently trigger controlled outputs. Output options:
a) Eight (8) Fail-Safe filtered power outputs.
b) Eight (8) Fail-Secure filtered power outputs.
c) Eight (8) form “C” relay outputs (rated @ 5A/24VDC or VAC).
d) Any combination of the above.
• Eight (8) Access Control System trigger inputs. Input trigger options:
a) Eight (8) normally open (NO) dry trigger inputs.
b) Eight (8) open collector inputs.
c) Any combination of the above.
• Eight (8) unswitched filtered aux. power outputs (outputs are rated @ 2.5A).
• Red LEDs on ACM8 board indicate individual outputs are triggered (relays energized).
• Fire Alarm disconnect (latching or non-latching) is individually selectable for any or all of the eight (8) outputs.
Fire Alarm disconnect input trigger options:
a) Normally open (NO) or normally closed (NC) dry trigger input.
b) Polarity reversal input from FACP signaling circuit.
• Green LED on ACM8 board indicates FACP disconnect is triggered.
• FACP output relay indicates that FACP input is triggered (form “C” contact rated @ 1A/28VDC not evaluated by UL).
• eFlow Power Supply/Charger provides common power for ACM8 board and all connected access control devices.
• ACM8 board main fuses are rated @ 10A. Output fuses are rated @ 3.5A.
eFlow Power Supply/Charger:
• Input: 120VAC, 60Hz.
• For output voltage and supply current refer to eFlow ACM series Configuration Chart, pg. 2.
• Auxiliary Power-Limited output rated @ 1A (unswitched).
- 2 -­
eFlow4NA8, eFlow6NA8, eFlow102NA8, eFlow104NA8 series
• Overvoltage protection.
• Built-in charger for sealed lead acid or gel type batteries.
• Maximum charge current 1.54A.
• Automatic switch over to stand-by battery when AC fails. Transfer to stand-by battery power is instantaneous with no interruption.
• Supervised Fire Alarm disconnect (latching or non-latching) 10K EOL resistor. Operates on a normally open (NO) or
normally closed (NC) trigger.
• AC fail supervision (form “C” contacts).
• Battery fail and presence supervision (form “C” contacts).
• Low power shutdown. Shuts down DC output terminals if battery voltage drops below 71-73% for 12V units and 70-75% for
24V units (depending on the power supply). Prevents deep battery discharge.
• For fuse rating, refer to eFlow ACM series Configuration Chart, pg. 2.
• Green AC Power LED indicates 120VAC present.
• AC input and DC output LED indicators.
• Short circuit and overload protection.
• Enclosure accommodates up to two (2) 12AH batteries.
Enclosure dimensions: 15.5” x 12” x 4.5” (393.7mm x 304.8mm x 114.3mm).
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, The Canadian Electrical Code, Part I, Part II
and with all local codes and authorities having jurisdiction. The product must be located indoors within the protected premises.
Power Supply Board LED Diagnostics
(pg. 5)
Access Power Controller LED Diagnostics
(pg. 5)
Power Supply Board Terminal Identification
(pg. 5)
Access Power Controller Terminal Identification
(pg. 5)
Power Supply Board Stand-by Battery Specifications
(pg. 6)
Power Supply Board Output Voltage Settings
(pg. 6)
Access Power Controller Typical Application Diagram
(pg. 6)
FACP/Optional Power Supply Hook-up Diagrams
(pg. 9)
1. Mount unit in desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the enclosure. Install
two upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the two
upper screws, level and secure. Mark the position of the lower two holes. Remove the enclosure. Drill the lower holes and install
the two fasteners. Place the enclosure’s upper keyholes over the two upper screws. Install the two lower screws and make sure to
tighten all screws. Enclosure Dimensions, pg. 12).
2. Connect unswitched AC power (120VAC 60Hz) to terminals marked [L, N] (Fig. 3, pg. 7). Do not use terminal marked [G].
Use 14 AWG or larger for all power connections. Secure green wire lead attached to the chassis to earth ground.
Keep power-limited wiring separate from non power-limited wiring. Minimum 0.25” spacing must be provided (Fig. 3, pg. 7).
CAUTION: Do not touch exposed metal parts. Shut branch circuit power before installing or servicing equipment.
There are no user serviceable parts inside. Refer installation and servicing to qualified service personnel.
3. Select desired DC output voltage by setting SW1 to the appropriate position on the power supply board (eFlow4NA8
and eFlow6NA8) (Fig. 1, pg. 6). eFlow102NA8 power supply is factory set at 12VDC. eFlow104NA8 power supply
is factory set at 24VDC.
4. Measure the output voltage of the unit before connecting any devices to ensure proper operation.
Improper or high voltage will damage these devices.
5. Output options (Fig. 2, pg. 6):
The unit will provide either eight (8) switched power outputs, eight (8) dry form “C” outputs, or any
combination of both switched power and form “C” outputs.
(a) Fail-Safe Switched Power outputs:
For Fail-Safe operation connect the positive (+) input of the access control devices to terminal marked [NC].
Connect the negative (-) input of the access control devices to terminal marked [COM].
(b) Fail-Secure Switched Power outputs:
For Fail-Secure operation connect the positive (+) input of the access control devices to terminal marked [NO].
Connect the negative (-) input of the access control devices to terminal marked [COM].
(c) Form “C” outputs:
When form “C” outputs are desired, the corresponding output fuses (1-8) of each ACM8 board must be removed.
6. ACM8 Auxiliary Power outputs (unswitched):
Connect access control devices that require constant power to terminals marked [C] positive (+) and [COM] negative (-).
Outputs can be used to provide power for card readers, keypads etc.
eFlow Auxiliary outputs (unswitched):
For auxiliary device connection this output will not be affected by Low Power Disconnect or Fire Alarm Interface.
Connect device to terminals marked [+ AUX -- ] (Fig. 3, pg. 7).
7. Input trigger options (Fig. 2, pg. 6):
(a) Normally Open [NO] input trigger:
Inputs 1-8 are activated by normally open or open collector sink inputs. Connect access control panel outputs,
keypads, push buttons, REX PIRs, etc. to terminals marked [IN] and [GND].
eFlow4NA8, eFlow6NA8, eFlow102NA8, eFlow104NA8 series
- 3 -­
(b) Open Collector Sink inputs:
Connect the access control panel open collector sink positive (+) to terminals marked [IN] and the negative (-)
to terminals marked [GND].
8. ACM8 Fire Alarm Interface options (Figs. 5-10, pg. 9):
A normally closed [NC] or normally open [NO] input trigger from a fire alarm control panel or a polarity reversal
input from an FACP signaling circuit will affect selected outputs. To enable FACP Disconnect for an output
turn the corresponding switch(es) [SW1-SW8] OFF on each ACM8 board. To disable FACP disconnect for an
output turn the corresponding switch(es) [SW1-SW8] ON on each ACM8 board.
(a) Normally Open [NO] input:
For non-latching hook-up refer to (Fig. 7, pg. 9). For latching hook-up refer to (Fig. 8, pg. 9).
(b) Normally Closed [NC] input:
For non-latching hook-up refer to (Fig. 9, pg. 9). For latching hook-up refer to (Fig. 10, pg. 9).
(c) FACP Signaling Circuit input trigger:
Connect the positive (+) and negative (-) from the FACP signaling circuit output to the terminals marked
[+ INP -]. Connect the FACP EOL to the terminals marked [+ RET -] (polarity is referenced in an alarm
condition). Jumper located next to TRG LED must be cut (Fig. 6, pg. 9).
9. FACP Dry form “C” output (Fig. 2b, pg. 6) (Not evaluated by UL):
Connect desired device to be triggered by the unit’s dry contact output to the terminals marked [NO] and [C]
FACP for normally open output or the terminals marked [NC] and [C] FACP for normally closed output.
10. Stand-by Battery Connections (Fig. 3, pg. 7):
For U.S. Access Control applications batteries are optional. Batteries are required for Canadian installations (ULC-S319).
When batteries are not used, a loss of AC will result in the loss of output voltage. When the use of stand-by batteries
is desired, they must be lead acid or gel type.
Connect battery to terminals marked [-- BAT + ] (Fig. 3, pg. 7). Use two (2) 12VDC batteries connected in series for 24VDC operation (battery leads included). Use batteries - Casil CL1270 (12V/7AH), CL12120 (12V/12AH), CL12400 (12V/40AH), CL12650 (12V/65AH) batteries or UL recognized BAZR2 and BAZR8 batteries of an appropriate rating.
11. Battery and AC Supervision outputs (Fig. 3, pg. 7):
It is required to connect supervisory trouble reporting devices to outputs marked [AC Fail, BAT Fail] supervisory relay outputs marked [NC, C, NO] to appropriate visual notification devices. Use 22 AWG to 18 AWG for AC Fail & Low/No Battery reporting.
12. To delay AC reporting for 2 hrs. set dip switch [AC Delay] to OFF position (Fig. 3, pg. 7).
To delay AC reporting for 1 min. set dip switch [AC Delay] to ON position (Fig. 3, pg. 7).
13. Fire Alarm Disconnect (Fig. 3, pg. 7):
To enable Fire Alarm Disconnect set dip switch [Shutdown] to ON position.
To disable Fire Alarm Disconnect set dip switch [Shutdown] to OFF position.
14. Installation of tamper switch (Not Included) (Fig. 3a, pg. 7):
Mount UL Listed tamper switch (Sentrol model 3012 or equivalent) at the top of the enclosure. Slide the tamper switch bracket onto the edge of the enclosure approximately 2” from the right side (Fig. 3a, pg. 7). Connect tamper switch wiring to the Access Control Panel input or the appropriate UL Listed reporting device. To activate alarm signal open the door of the enclosure.
15. Multiple power supply inputs (Fig. 2, pg. 6) (Not evaluated by UL):
When using an additional Listed external power supply, jumpers J1 and J2 located on corresponding ACM8 board must
be cut (Fig. 2c, 2d, pg. 6 and Fig. 5, pg. 9). Connect external Listed power-limited access control power supply to the terminals
marked [- Control +] (These terminals are paralleled to the - Power + terminals). When using DC power supplies, polarity must
be observed. When using AC power supplies, polarity needs not be observed (Fig. 2d, pg. 6). All field wiring connections must
be made employing suitable gauge CM or FPL jacketed wire (or equivalent substitute) (Fig. 4a, pg. 8).
Maintenance:
Unit should be tested at least once a year for the proper operation as follows:
FACP Supervision: To ensure proper connection and operation of the Fire Alarm disconnect hookup please follow the appropriate
procedure below:
Normally Open Input: Placing a short between terminals marked [T] and [+ INP] will trigger the Fire Alarm Disconnect. Remove the short to reset.
Normally Closed Input: Removing the wire from terminal marked [INP -- ] will trigger the Fire Alarm Disconnect.
Replace the wire to terminal marked [INP -- ] to reset.
FACP Signal Circuit Input: It is necessary to trigger the Fire Alarm System. In all of the above scenarios the green TRG LED
of the ACM8 will illuminate. All outputs selected for Fire Alarm Disconnect will activate releasing locking devices.
Note: All outputs [OUT 1 - OUT 8] must be in a normal (de-energized) condition prior to testing. When the unit is configured for
Normally Open (Fig. 8, pg. 9) or Normally Closed (Fig. 10, pg. 9) latching operation, it is necessary to reset the Fire Alarm Disconnect by activating the Normally Closed reset switch.
Output Voltage Test: Under normal load conditions the DC output voltage should be checked for proper voltage level
(refer to eFlow ACM series Configuration Chart, pg. 2).
Battery Test: Under normal load conditions check that the battery is fully charged, check specified voltage at the battery terminals
and at the board terminals marked [+ BAT – ] to ensure that there is no break in the battery connection wires.
Note: Maximum charge current is 1.54A.
Expected battery life is 5 years; however, it is recommended to change batteries within 4 years or less if necessary.
- 4 -­
eFlow4NA8, eFlow6NA8, eFlow102NA8, eFlow104NA8 series
Power Supply Board LED Diagnostics:
Red (DC)
ON
ON
OFF
OFF
Green (AC/AC1)
ON
OFF
ON
OFF
Power Supply Status
Normal operating condition.
Loss of AC. Stand-by battery supplying power.
No DC output.
Loss of AC. Discharged or no stand-by battery. No DC output.
Access Power Controller LED Diagnostics:
LED
LED 1- LED 8 (Red)
Trg (Green)
ON
Output relay(s) energized.
FACP input triggered (alarm condition).
OFF
Output relay(s) de-energized.
FACP normal (non-alarm condition).
Power Supply Board Terminal Identification:
Terminal Legend
L, N
+ DC –
Trigger EOL
Supervised
NO, GND RESET
+ AUX –
AC FAIL
NC, C, NO
BAT FAIL
NC, C, NO
+ BAT –
Function/Description
Connect 120VAC 60Hz to these terminals: L to hot, N to neutral. Do not use terminal marked [G]
Factory connected to ACM8 board.
Fire Alarm Interface trigger input from a short or FACP. Trigger inputs can be normally open,
normally closed from an FACP output circuit (power-limited input) (Fig. 3, pg. 7).
FACP interface latching or non-latching (power-limited) (Fig. 3, pg. 7).
Auxiliary Power-Limited output rated @ 1A (unswitched) (power-limited output) (Fig. 3, pg. 7).
Indicates loss of AC power, e.g. connect to audible device or alarm panel. Relay normally energized
when AC power is present. Contact rating 1A @ 30VDC (power-limited) (Fig. 3, pg. 7).
Indicates low battery condition, e.g. connect to alarm panel. Relay normally energized when DC power
is present. Contact rating 1A @ 30VDC. A removed battery is reported within 5 minutes.
Battery reconnection is reported within 1 minute (power-limited) (Fig. 3, pg. 7).
Stand-by battery connections. Maximum charge current 1.54A (non power-limited) (Fig. 3, pg. 7).
Access Power Controller Terminal Identification:
Terminal Legend
-- Power +
-- Control +
Function/Description
12VDC or 24VDC from power supply/charger (factory connected).
These terminals are paralleled to the - Control + terminals.
These terminals are paralleled to the - Power + terminals.
These terminals can be connected to an external Listed power-limited access control power supply to provide
isolated operating power for the devices (Not evaluated by UL). Jumpers J1 and J2 must be removed.
TRIGGER
INPUT 1-INPUT 8
IN, GND
From normally open and/or open collector sink trigger inputs
(request to exit buttons, exit pir’s, etc.)
OUTPUT 1OUTPUT 8
NC, C, NO, COM
12VDC to 24VDC trigger controlled outputs:
eFlow4NA8 - 10.1-13.2VDC @ 3.3A or 20.28-26.4VDC @ 3.6A.
eFlow6NA8 - 10.0-13.2VDC @ 5.3A or 20.19-26.4VDC @ 5.6A.
eFlow102NA8 - 10.03-13.2VDC @ 9.3A.
eFlow104NA8 - 20.17-26.4VDC @ 9.6A.
Fail-Safe [NC positive (+) & COM Negative (-)], Fail-Secure [NO positive (+) & COM Negative (-)],
Auxiliary output [C positive (+) & COM Negative (-)] (When using AC power supplies polarity needs not
to be observed), NC, C, NO convert to dry form “C” 5A 24VAC/VDC rated dry outputs when fuses
are removed. Contacts shown in a non-triggered state.
FACP INTERFACE Fire Alarm Interface trigger input from FACP. Trigger inputs can be normally open,
T, + INPUT -normally closed from an FACP signaling circuit output (Figs. 5-10, pg. 9).
FACP INTERFACE
Form “C” relay contact rated @ 1A 28VDC for alarm reporting (not evaluated by UL).
NC, C, NO
eFlow4NA8, eFlow6NA8, eFlow102NA8, eFlow104NA8 series
- 5 -­
eFlow4NA8
30 Mins./4A*
35 Mins./4A*
Over 4 Hours/4A*
Over 4 Hours/4A*
eFlow6NA8
10 Mins./6A
30 Mins./6A*
Over 4 Hours/6A*
Over 4 Hours/6A*
eFlow102NA8
5 Mins./10A
30 Mins./10A*
Over 2 Hours/10A*
Over 4 Hours/10A*
eFlow104NA8
5 Mins./10A
30 Mins./10A*
Over 2 Hours/10A*
Over 4 Hours/10A*
*Only these configurations can be utilized in ULC-S319 installations.
Power Supply Board Output Voltage Settings:
Fig. 1
Fig. 1a
Switch Detail
ON
Switch On - 12V
1
ON
OFF --- 24V
ON --- 12V
Power Supply Board Stand-by Battery Specifications:
Battery
7AH
12AH
40AH
65AH
1
--- DC +
ON
Switch Off - 24V
Access Power Controller Typical Application Diagram (ACM8):
Fig. 2
Fig. 2a
Intact = Dry Input
Cut = Wet Input
Normally Open (N.O.)
Door Releasing
Device
FACP
Keypad
Access Control Panel
FACP
(Fire Alarm
Control
Panel)
TRG
C
NO
FACP Dry
Form "C" Output
NO C NC + INP --- T + RET FACP
INTERFACE
TRG
IN GND IN GND IN GND IN GND
1
2
3
4
F1
F2
F3
IN GND IN GND IN GND IN GND
5
6
7
8
F4
F5
F6
F7
F8
ON
ON
2
3
4
1
2
3
4
SW1-SW8
FACP Interface
ON
1
1
FACP
Fig. 2b
NO C NC
FACP
NC
Disabled
1
Output
Relay
Enabled
MAIN
10A 250V
LED4
LED5
LED6
LED7
LED8
Mag.
Lock
J2 J1
J3
NC C NO COM NC C NO COM
OUTPUT 1
OUTPUT 2
NC C NO COM NC C NO COM
OUTPUT 3
OUTPUT 4
NC C NO COM NC C NO COM
OUTPUT 5
OUTPUT 6
NC C NO COM NC C NO COM
OUTPUT 7
OUTPUT 8
AC or DC
Power
Supply
(req'd.)
Electric
Strike
Electromagnetic
Door Holders
UL Listed
Power Supply
For this application
corresponding
fuse F8 must be
removed.
MAG.
LOCK
J3
Intact = DC Input
Cut = AC Input
Fig. 2d
Fig. 2c
Intact = One P/S Input
Cut = Dual P/S Input
J2 J1
NC C NO COM
OUTPUT 8
- 6 -­
AC or DC
Power
Supply
(optional)
--- +
Control
LED3
ON
LED2
--- + --- +
Power Control
LED1
eFlow4NA8, eFlow6NA8, eFlow102NA8, eFlow104NA8 series
Fig. 3a
--- DC +
Green
Lead
(ground)
Enclosure
Door
Battery & AC
Supervision
Circuit
(Power-limited)
C
--- BAT +
(eFlow4NA8 power-limited)
(eFlow6NA8, eFlow102NA8,
eFlow104NA8 non power-limited)
SHUTDOWN
AC
AC DELAY
AC1
DC
NO
C
NO
NC
2 hr.
1 min.
NC
TRIGGER EOL disable
SUPERVISED enable
RESET
GND
NO
AC FAIL
5A 250V
L
Observe polarity
Power-limited
unswitched 120VAC
power mains
(non power-limited)
Wire
Strap
(from
Enclosure
to Door)
Tamper Switch
– AUX +
BAT FAIL
G
Battery
Connections
(Non Power-limited)
O
N
120VAC
power mains
Non Powerlimited
Edge of
Enclosure
to Access Control Panel
or U.L. Listed
Reporting Device
ON
OFF --- 24V
ON --- 12V
Sentrol
model # 3012
Tamper Switch
or equivalent
(Not Included)
N
Fig. 3
Insulating
Barrier
TRG
IN GND IN GND IN GND IN GND
1
2
3
4
F1
F2
F3
F4
IN GND IN GND IN GND IN GND
5
6
7
8
F5
F6
F7
F8
ON
1
ON
2
3
4
1
2
3
4
NO C NC + INP --- T + RET FACP
INTERFACE
Inputs (power-limited)
Fire Alarm
Interface
(power-limited)
MAIN
10A 250V
LED2
LED3
LED4
LED5
LED6
LED7
LED8
J3
NC C NO COM NC C NO COM
OUTPUT 1
OUTPUT 2
NC C NO COM NC C NO COM
OUTPUT 3
OUTPUT 4
NC C NO COM NC C NO COM
OUTPUT 5
OUTPUT 6
J2 J1
NC C NO COM NC C NO COM
OUTPUT 7
OUTPUT 8
--- + --- +
Power Control
LED1
DC Output to devices (power-limited for eFlow4NA8,
non power-limited for all other models*)
Optional Rechargeable Stand-by Battery
for UL294 Applications
Optional Rechargeable Stand-by Battery
for UL294 Applications
Note: 12V batteries required for
ULC-S319 installations.
Note: 12V batteries required for
ULC-S319 installations.
CAUTION: When power supply board is set for 12VDC use only one (1)
12VDC stand-by battery.
Keep power-limited wiring separate from non power-limited.
Use minimum 0.25" spacing.
12AH Rechargeable batteries are the largest batteries that can fit in this
enclosure. A UL listed external battery enclosure must be used if using
the 40AH or 65AH batteries.
eFlow4NA8, eFlow6NA8, eFlow102NA8, eFlow104NA8 series
- 7 -­
NEC Power-Limited Wiring Requirements for eFlowNA8 Models:
Power-limited and non power-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring
must remain at least 0.25” away from any non power-limited circuit wiring. Furthermore, all power-limitedcircuit wiring
and non power-limited circuit wiring must enter and exit the cabinet through different conduits. One such example of this
is shown below. Your specific application may require different conduit knockouts to be used. Any conduit knockouts may
be used. For power-­limited applications use of conduit is optional. All field wiring connections must be made employing
suitable gauge CM or FPL jacketed wire (or equivalent substitute).
Optional UL Listed battery enclosure must be mounted adjacent to the power supply via Class 1 wiring methods.
For Canadian installations use shielded wiring for all connections.
Note: Refer to wire handling drawing below for the proper way to install the CM or FPL jacketed wire (Fig. 4a).
Supervisory Connections
(power-limited)
Fig. 4
Optional
UL Listed
Battery Enclosure
(non power-limited)
120VAC Input
60Hz
(non power-limited)
ACM8 outputs*
Battery
Connections
(non power-limited)
Fig. 4a
Incorrect Wire
Handling
Correct Wire
Handling
External
Jacketed
Shield
Wire
Insulation
Solid Copper
Conductors
- 8 -­
Pull back
external jacketed
shield approx. 1/2”.
*Outputs are power-limited on eFlow4NA8.
Outputs are non power-limited for eFlow6NA8, eFlow102NA8,
and eFlow104NA8.
eFlow4NA8, eFlow6NA8, eFlow102NA8, eFlow104NA8 series
FACP Hook-Up Diagrams:
Fig. 5 Optional hook-up using two (2) isolated power Fig. 6 Polarity reversal input from FACP signaling circuit
supply inputs (Only applicable on eFlow4NA8)
output (polarity is referenced in alarm condition):
(Not evaluated by UL):
TRG
J2
J1
ISOLATED POWER INPUT
12 OR 24 VAC OR VDC
(ACM8 POWER)
FACP
OUTPUT EOL
-- FROM FACP
OUTPUT
+
CIRCUIT
NO C NC
FACP
ISOLATED POWER INPUT
12 OR 24 VAC OR VDC
(LOCK POWER)
INTERFACE
CUT
JUMPER
CUT JUMPERS
J1 AND J2
Fig. 7 Normally Open - Non-Latching FACP
Fig. 8 Normally Open FACP Latching trigger input
trigger input:
with reset:
(This output has not been evaluated by UL)
INTERFACE
TRG
N.O.
TRIGGER
INPUT
N.O. TRIGGER
INPUT
N.C. RESET
SWITCH
JUMPER
NO C
NC
NO C NC
FACP
TRG
Fig. 9 Normally Closed - Non-Latching FACP
Fig. 10 Normally Closed - Latching FACP trigger input
trigger input:
with reset:
(This output has not been evaluated by UL)
TRG
INTERFACE
NO C NC
FACP
TRG
N.C. RESET
SWITCH
N.C. DRY
TRIGGER
INPUT
JUMPER
eFlow4NA8, eFlow6NA8, eFlow102NA8, eFlow104NA8 series
JUMPER
N.C. TRIGGER
INPUT
- 9 -­
Notes
- 10 -­
eFlow4NA8, eFlow6NA8, eFlow102NA8, eFlow104NA8 series
Notes
eFlow4NA8, eFlow6NA8, eFlow102NA8, eFlow104NA8 series
- 11 -­
Enclosure Dimensions (BC400) (approximate H x W x D):
15.5” x 12” x 4.5” (393.7mm x 304.8mm x 114.3mm)
1.5”
(38.1mm)
4.615”
(117.22mm)
4.615”
(117.22mm)
1.5”
(38.1mm)
1.75”
(44.45mm)
1.75”
(44.45mm)
4.5”
(114.3mm)
12.23”
(310.64mm)
1.1”
(27.94mm)
0.91”
(23.114mm)
1.5”
(38.1mm)
4.5”
(114.3mm)
1.1”
(27.94mm)
0.91”
(23.114mm)
1.75”
(44.45mm)
1.375”
(34.925mm)
1.5”
(38.1mm)
1.125”
(28.575mm)
15.5”
(393.7mm)
2.0”
(50.8mm)
2.0”
(50.8mm)
5.0”
(127.0mm)
2.5”
(63.5mm)
1.1”
(27.94mm)
1.75”
(44.45mm)
0.79”
(20.06mm)
1.75”
(44.45mm)
1.75”
(44.45mm)
1.5”
(38.1mm)
4.615”
(117.22mm)
4.615”
(117.22mm)
1.5”
(38.1mm)
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: 718-567-9056
web site: www.altronix.com, e-mail: [email protected] Lifetime Warranty, Made in U.S.A.
IIeFlowACM series
- 12 -­
F06P
MEMBER
eFlow4NA8, eFlow6NA8, eFlow102NA8, eFlow104NA8 series
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement