Touch interface. This information can be used to verify that the device has an IP address and that it is receiving and sending packets to the network. You can also detect if packets are lost (dropped or in error). This can help identifying network problems that may cause issues in calls.

IPv6 and dual stack support

IPv6 and dual stack operation are fully supported, also when using ActiveControl and ICE.

Use the following settings if you want to enable dual stack operation with IPv6 as the preferred protocol:

Network 1 IPStack: Dual

(enables IPv4 and IPv6 network address (default))

Conference 1 CallProtocolIPStack: Dual

(enables dual stack operation for the call protocols)

SIP PreferredIPMedia: IPv6

(selects which IP version to prefer for media if both versions are supported on both ends)

SIP PreferredIPSignaling: IPv6

(selects which IP version to prefer for signaling if both versions are supported on both ends)

Presentation will stop when the presentation source is disconnected

If a presentation source is disconnected or goes into standby

(e.g. a PC), the presentation will automatically be ended after 10 seconds. If the source is connected or comes out of standby within 10 seconds, the presentation will automatically be resumed.

An input is available for presentation only when a content source (e.g. a PC) is connected to that input.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Web interface System settings

System configuration changes

New configurations

UserInterface UserPreferences: <Off/On>

Video Input Source [n] Visibility: <Never/Always/IfSignal>

Configurations that are removed

Conference Video SelfviewControl AutoResizing

Setting passwords

Administrator Guide

Appendices

Configurations that are modified

Audio SoundsAndAlerts RingTone

OLD: <Marbles/IceCrystals/Polaris/Alert/Discreet/Fantasy/

Jazz/Nordic/Echo/Rhythmic>

NEW: <S: 1, 100>

Provisioning Mode

OLD: <Off/TMS/VCS/CallWay/CUCM/Auto>

NEW: <Off/TMS/VCS/CallWay/CUCM/Auto/Edge>

UserInterface TouchPanel DefaultPanel

OLD: <ContacList/MeetingList/Dialpad>

NEW: <None/LastUsed/ContacList/MeetingList/Dialpad>

Video Input Source [n] PresentationSelection

OLD: <Manual/Automatic/Hidden>

NEW: <Manual/Automatic/OnConnect/Hidden>

Video WallPaper

OLD: <None/Custom/Growing/Summersky/Waves>

NEW: <None/Custom/Growing/Summersky/Waves/Blue>

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Web interface

Profile 42” using Codec C40 at a glance

See the installation sheet for the Profile 42” for instructions on how to install the system.

Codec C40

• Full HD video

• High resolution data sharing

• Full HD Multisite

• Rich I/O capabilities

PrecisionHD 1080p camera

Full HD Camera designed for visual communication with:

• 12 × optical zoom

• Fast and precise pan, tilt and zoom

Monitor

42” Full HD LCD, 16:9, 1080 × 1920 resolution

Audio module

Wide band audio module supporting:

• 20 kHz AAC-LD

• Full echo canceling

• Stereo

Audio amplifier

Optimized DNAM for the Profile system, providing crystal clear and natural audio

Microphones

2 × Microphones

Operating devices

• Touch 8 controller (for C Series)

• Remote control with AAA batteries

Base options

Floor standing footplate, wheel base, or wall mount on pedestal

Ethernet cable

PC cable

Mic cable

Power cable

System settings

Floor standing footplate

(Other options: Wheel base or wall mount on pedestal)

Setting passwords

Touch 8 controller

PrecisionHD 1080p camera

Monitor 42’’

Full HD LCD

In the bottom module:

• Audio amplifier (DNAM)

• Codec C40

Administrator Guide

Appendices

Remote control

2 × Microphones with cables

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Web interface

Profile 52”/55” at a glance

See the installation sheets for the Profile 52”/55” for instructions on how to install the system.

Codec C60/C40

• Full HD video

• High resolution data sharing

• Full HD Multisite

• Rich I/O capabilities

PrecisionHD 1080p camera

Full HD Camera designed for visual communication with:

• 12 × optical zoom

• Fast and precise pan, tilt and zoom

Monitor

52”/55” Full HD LCD, 16:9, 1080 × 1920 resolution

Audio module

Wide band audio module supporting:

• 20 kHz AAC-LD

• Full echo canceling

• Stereo

Audio amplifier

Optimized DNAM for the Profile system, providing crystal clear and natural audio

Microphones

Three (with C60) / Two (with C40) microphones with cables

Operating devices

• Touch 8 controller

• Remote control with AAA batteries

Base options

Floor standing footplate, wheel base, or wall mount on pedestal

Ethernet cable

PC cable

Mic cable

Power cable

Floor standing footplate

(Other options: Wheel base or wall mount on pedestal)

System settings

Touch 8 controller

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Setting passwords

PrecisionHD 1080p camera

Administrator Guide

Appendices

In the bottom module:

• Audio amplifier (DNAM)

• Codec C60/C40

Remote control

Monitor 52’’/55”

Full HD LCD

Three/two microphones

(Profiles using

Codec C40)

(Profiles using

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Web interface

Profile 52” Dual / 55” Dual at a glance

See the installation sheets for the Profile 52” Dual / 55” Dual for instructions on how to install the system.

Codec C60

• Full HD video

• High resolution data sharing

• Full HD Multisite

• Rich I/O capabilities

PrecisionHD 1080p camera

Full HD Camera designed for visual communication with:

• 12 × optical zoom

• Fast and precise pan, tilt and zoom

Dual monitor

Dual 52” / Dual 55” Full HD LCD, 16:9, 1080 × 1920 resolution

Audio module

Wide band audio module supporting:

• 20 kHz AAC-LD

• Full echo canceling

• Stereo

Audio amplifier

Optimized DNAM for the Profile system, providing crystal clear and natural audio

Microphones

Four microphones with cables

Operating devices

• Touch 8 controller

• Remote control with AAA batteries

Base options

Floor standing footplate or wall mount on pedestal

Ethernet cable

PC cable

Mic cable

Power cable

Floor standing footplate

(Other option:

Wall mount on pedestal)

System settings

Touch 8 controller

Administrator Guide

Appendices Setting passwords

PrecisionHD 1080p camera

Dual 52’’/ Dual 55” monitor

Full HD LCD

Remote control

In the bottom module:

• Audio amplifier (DNAM)

• Codec C60

Four microphones

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Web interface

Profile 65” at a glance

See the Profile 65” Installation Sheet for instructions of how to assemble the system.

Codec C60

• Full HD video

• High resolution data sharing

• Full HD Multisite

• Rich I/O capabilities

PrecisionHD 1080p camera

Full HD Camera designed for Visual communication with:

• 12 × optical zoom

• Fast and precise pan, tilt and zoom

Monitor 65”

65” Full HD LCD, 16:9, 1080 × 1920 resolution

Audio module

Wide band audio module supporting:

• 20 kHz AAC-LD

• Full echo canceling

• Stereo

Audio amplifier

Optimized DNAM for the Profile system, providing crystal clear and natural audio

Microphones

Three microphones with cables

Operating devices

• Touch 8 controller

• Remote control with AAA batteries

Base options

Floor standing footplate or wall mount on pedestal

Ethernet cable

PC cable

Mic cables

Power cable

System settings

Floor standing footplate

(Other option:

Wall mount on pedestal)

Setting passwords

Touch 8 controller

Administrator Guide

Appendices

PrecisionHD 1080p camera

Monitor 65”

Full HD LCD

In the bottom module:

• Audio amplifier (DNAM)

• Codec C60

Remote control

Three microphones

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Web interface System settings

Codec C60 at a glance

The Codec C60 is the 1080p HD video collaboration engine.

Based upon the same technology as the Codec C90, the C60 delivers Full HD video, HD collaboration and superior audio for natural communication at its finest, delivering unrivaled value.

The C60 is a standards-compliant codec for integration into team meeting rooms, boardrooms and industry projects.

• Full High Definition Video with up to 4 HD sources, and collaboration with optimal definition for the best video quality every time, regardless of environment.

• Highest Quality Audio with flexibility to add up to 4 microphones directly from the codec, and superior, full duplex audio with high quality stereo sound.

• Full APIs.

• Ensure successful, streamlined integration projects with standards-compliant professional connectors.

Setting passwords

Administrator Guide

Appendices

Integrator package

The integrator package of the Codec C60 comes with the

PrecisionHD 1080p camera, microphone and cables.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Web interface

Codec C40 at a glance

The Codec C40 provides all the power required to transform any conference room to a HD video collaboration room.

Designed for any standard HD integration project, the Codec

C40 is the ideal solution for everyday video conferencing and collaboration solution. 1080p HD video, and Multisite™ features combine to make the Codec C40 ideal for a variety of applications.

System settings

The Codec C40 is ideal for standard meeting rooms, executive offices and team collaboration rooms.

• Full High Definition Video with up to 2 HD sources, and collaboration with optimal definition for the best video quality every time, regardless of environment.

• Highest Quality Audio with flexibility to add up to 2 microphones directly from the codec, and superior, full duplex audio with high quality stereo sound.

• Full APIs.

• Ensure successful, streamlined integration projects with standards-compliant professional connectors.

Setting passwords

Administrator Guide

Appendices

Integrator package

The integrator package of the Codec C40 comes with the

PrecisionHD 1080p camera, microphone and cables.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction System settings Setting passwords

Administrator Guide

Appendices

Chapter 2

Web interface

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

Accessing the web interface

The web interface provides full configuration access to your video conference system.

You can connect from a computer and administer the system remotely.

In this chapter you will find information how to use the web interface for system configuration and maintenance.

We recommend that you use the latest release of one of the major web browsers.

System settings

1. Connect to the video system

Open a web browser and enter the IP address of the video system in the address bar.

To find the IP address (IPv4 or IPv6), open the

Settings

menu on the Touch controller and tap

System Information

; or navigate to

Home > Settings >

System information

when using a remote control and the on-screen menu.

Setting passwords

2. Sign in

Enter the user name and password for your video system and click

Sign In

The system is delivered with a default user named admin with no password

(i.e. leave the

Password

field blank when signing in for the first time).

We strongly recommend that you set a password for the admin user, see the next page.

Administrator Guide

Appendices

* The

Settings

menu can be accessed from the drop down window that appears when you tap the contact information in the upper, left corner of the Touch controller.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Signing out

Hover the mouse over your user name and choose

Sign out

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

Changing the system password

We strongly recommend that you set a password for any user with ADMIN rights in order to restrict access to system configuration. This includes the default

admin user.

A warning, saying that the system password is not set, is shown on screen until you set a password.

You can read more about password protection in the

► Setting passwords chapter.

System settings

1. Open the Change Password dialog

Hover the mouse over your user name, and choose

Change password

in the drop-down list.

Setting passwords

Administrator Guide

Appendices

2. Set the new password

Enter your current and new passwords as requested, and click

Change password

for the change to take effect.

If the password currently is not set, leave the

Current password

field blank.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction System settings

The interactive menu

The web interface provides access to tasks and configurations. They are available from the main menu, which appears near the top of the page when you have signed in.

When you hover the mouse over an item in the main menu, you can navigate to its related sub-pages.

Main menu

Hover the mouse over a main menu item in order to see the titles of the related sub-pages.

Click a sub-page’s title to open it. Click the main menu item itself if there are no sub-pages.

Only pages that the user has access rights for are shown

Click

Home

to return to the System Information page.

Setting passwords

Administrator Guide

Appendices

Sub-pages

Call Control Configuration

System Configuration

System Status

Favorites Management

Personalization

Peripherals

User Administration

Startup Scripts

API

Security

Diagnostics

Troubleshooting

Call History

Log Files

Maintenance

Software Upgrade

Backup and Restore

System Recovery

Restart

You can read more about user administration, user roles and access

rights in the

► User administration

section.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

System information

The video system’s Home page shows an overview of the basic set-up and status of the system

This includes information like system name and product type, which software version the system runs, its IP address, etc.

Also the registration status for the video networks (SIP and

H.323) is included, as well as the number/URI to use when making a call to the system.

Navigate to: Home

System settings Setting passwords

Administrator Guide

Appendices

The system information shown in the illustration serve as an example. Your system may be different.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

Placing a call

You can use the Call Control page to place a call.

Even if the web interface is used to initiate the call, it is the video system (display, microphones and loudspeakers) that is used for the call; it is not the PC running the web interface.

Calling

You can call someone either by choosing a contact name in the Favorites, Directory or History lists, or by typing a complete URI or number in the Search or Dial field. Then click

Call

in the associated contact card.

Searching the contact lists

Enter one or more characters in the Search or Dial field.

Matching entries from the Favorites, Directory and History lists will be listed as you type.

Select the correct entry in the list before you click

Call

Calling more than one

A point-to-point video call (a call involving two parties only) may be expanded to include more participants.

If your system supports the optional built-in MultiSite feature, up to four participants, yourself included, can join the video call (conference).

One additional participant can join on audio-only.

Follow the same procedure to call the next conference participant as you did when calling the first participant.

Navigate to: Call Control

System settings

Calling someone

Click a contact name, either in the

Favorites, Directory or History lists. Then click

Call

in the contact card.

Alternatively, enter the complete URI or number in the Search and Dial field.

Then click the

Call

button that appears next to the URI or number.

Setting passwords

Holding and resuming

Use the button next to the participant’s name to put him on hold.

To resume the call, use the button that is present when a participant is on hold.

Administrator Guide

Appendices

Ending a call

If you want to terminate a call or conference, click

End

All

Confirm your choice in the dialog that appears.

To disconnect just one participant in a conference, click the button for that participant.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

Sharing content

You can connect a presentation source to one of the external inputs of your video system. Most often a PC is used as presentation source, but other options may be available depending on your system setup.

While in a call you can share content with the far end, that is the other participant(s) in the call.

If you are not in a call, the content is shared locally on your display.

Navigate to: Call Control

System settings Setting passwords

Administrator Guide

Appendices

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Sharing content

1. Choose a Presentation source from the drop-down list.

2. Click

Start Presentation

Stop content sharing:

Click the

Stop Presentation

button that is present while sharing.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

Controlling and monitoring a call

You can control and monitor several call features using the

Call Control page.

Navigate to: Call Control

Microphone mute

Click the button to mute the microphone.

Then the text changes to

Microphone: Off

Click again to unmute.

System settings Setting passwords

Volume down

Administrator Guide

Appendices

Volume up

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Show/hide

call details

Click the information button to show details about the call.

Click the button again to hide the information.

Call details

If necessary, scroll your browser to see the call details.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

Controlling your camera

You can control the camera from the Call Control page.

The camera controls (pan, tilt, zoom) are available when the cursor is placed in the Main Source video area. Live snapshots are automatically taken during this period.

Note that the camera controls are not availble if the system is in standby mode.

Navigate to: Call Control

System settings Setting passwords

Administrator Guide

Appendices

Choose which camera to control

Click the arrow to open the drop-down list. Then choose the camera you want to control.

Zoom

Use + and to zoom in and out.

Pan and tilt

Use the left and right arrows to pan the camera, and the up and down arrows to tilt it.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Camera presets

If a camera preset is defined it is listed here. Click the preset’s name to move the camera(s) to the preset position.

Click

to close the window.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

Local layout control

You can choose a local layout using the Call Control page.

The term layout is used to describe the various ways the videos from the conference participants and a presentation can appear on your screen. Different types of meetings will require different layouts.

Navigate to: Call Control

System settings Setting passwords

Administrator Guide

Appendices

Change the layout

Click

Change Layout

, and choose your preferred layout in the window that opens.

You may change the layout while in a call.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

Capturing snapshots

The snapshot feature, which is disabled by default, allows snapshots captured by your video system to be displayed on the Call Control page. Captures from your video system’s camera as well as from its presentation channel will be displayed.

This feature might come in handy when administering the video system from a remote location, e.g. to check the camera view.

To use web snapshots you have to sign in with ADMIN credentials.

Enabling the snapshot feature

The snapshot feature is disabled by default. The feature must be enabled using the remote control and on screen menu, or the Touch controlle r. The Touch controller must be directly connected to the codec’s second Ethernet port.

Touch controller:

• Open the

Settings

menu on the Touch controller and tap

Administrator

. You have to log in with an administrator user name and password to get access to the

Administrator

menu.

• Tap

Web Snapshots

and choose ON.

Remote control and on screen menu:

• Go to the Advanced configuration menu, navigate to

Video > AllowWebSnapshots

and choose On.

Far end snapshots while in a call

While in a call, snapshots of the remote participant’s main camera and presentation channel (far end) will be captured and displayed as shown in the illustration. The snapshots are updated approximately every 30 seconds.

Far end snapshots are captured even if web snapshots are disallowed on the far end video system. Web snapshots are prohibited only for encrypted calls.

* The

Settings

menu can be accessed from the drop down window that appears when you tap the contact information in the upper, left corner of the Touch controller.

Navigate to: Call Control

System settings

Take live snapshots

While the

Live snapshots

box is checked, snapshots are captured by your video system (main source and presentation source) approximately every two seconds.

Snapshots from your video system

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Setting passwords

Administrator Guide

Appendices

Far end snapshots

Click the snapshot in order to see a larger image.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

Controlling the far end camera

While in a call, you can control the remote participant’s camera (far end) provided that:

• The

Conference FarEndControl Mode

setting is switched

On on the far end video system.

• The far end camera has pan, tilt or zoom functionality.

Only the relevant controls will appear.

Navigate to: Call Control

System settings Setting passwords

Administrator Guide

Appendices

Far end camera control indicator

If this symbol is present, you can control the remote participant’s camera.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Control the remote participant’s camera

1. Click the snapshot to show it in a larger window.

2. Place the cursor in the image to enable the controls.

3. Use the left and right arrows to pan the camera; the up and down arrows to tilt it; and + and to zoom in and out.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

Accessing call information

A call state indicator is avaiable in the top bar in the web interface. It shows whether the system is in a call or not, and how many calls it is engaged in. You may also be notified about incoming calls.

System settings Setting passwords

Administrator Guide

Appendices

Call state indicator

The call state indicator is available on all pages except the

Call Control

page.

The badge indicates the number of active calls. If the system is idle, there is no badge.

Click the indicator to get more details about connected calls.

Call control

Use these buttons to:

• Show call details

• Put the call on hold

• Disconnect the call

Incoming call notification

As default, a notification is given when the system receives a call.

Check this box, if you do not want to receive such notifications.

Opening the Call Control page

Click

Open Call Control

to go straight to the

Call Control

page.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

System configuration

The system settings are grouped in several categories. When you choose a category in the left pane all related settings appear to the right

Each system setting is further described in the

► System settings chapter.

System settings Setting passwords

Administrator Guide

Appendices

Navigate to: Configuration > System Configuration

Searching for settings

Enter as many letters as needed in the search field.

All settings (value space included) containing these letters will be highlighted.

The configuration shown in the illustration serve as an example.

Your system may be configured differently.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Selecting a category

The system settings are structured in categories.

Choose a category in order to display the related settings.

Expanding and collapsing lists

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

Changing system settings

All system settings can be changed from the System

Configuration page

. The value space for a setting is specified either in a drop-down list or by text following the input field.

Different settings may require different user credentials. In order to be sure that an administrator is able to change all system settings, the user must possess all user roles.

You can read more about user administration and user roles in the

► User administration chapter.

System settings Setting passwords

Navigate to: Configuration > System Configuration

Drop-down list

Click the arrow to open the drop-down list. Choose the preferred value and click

Save

for the change to take effect.

Administrator Guide

Appendices

The configuration shown in the illustration serve as an example.

Your system may be configured differently.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Text input field

Enter text in the input field and click

Save

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

Setting the Administrator Settings menu password

This password restricts access to the Administrator Settings menu that is available on-screen when using the remote control.

When starting up the video conference system for the first time anyone can access these settings, because the menu password is not set.

We strongly recommend that you set a menu password, because the administrator settings may severely affect the behavior of the system.

Note that the menu password, as from software version

TC7.0, applies only to the on-screen Administrator Settings menu; it does not apply to the Administrator menu on the

Touch 8 controller.

You can read more about password protection in the

► Setting passwords chapter.

Changing the menu password

Click

Set/Change Administrator

Settings menu password

to open this dialog.

Enter the new password in the text input field and click

Set

to set it.

Click

Set

without entering a password to leave the

Administrator menu unprotected

(not recommended).

System settings

Navigate to: Configuration > System Configuration

Setting passwords

Administrator Guide

Appendices

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction System settings

System status

The system status is grouped in several categories. When you choose a category in the left column, the related status appears in the window to the right

Navigate to: Configuration > System Status

Setting passwords

Administrator Guide

Appendices

Searching for status entries

Enter as many letters as needed in the search field.

All entries (value space included) containing these letters will be highlighted.

Selecting a category

The system status is structured in categories. Choose a category in order to display the related status information.

The status shown in the illustration serve as an example. The status of your system may be different.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Expanding and collapsing lists

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

Managing the favorites list

The entries in the favorites list can be accessed from the

Touch controller, the on-screen menu (the My contacts folder in the phone book) and the Web interface.

System settings

Navigate to: Configuration > Favorites Management

Setting passwords

Administrator Guide

Appendices

Adding a contact

Click

Add contact

and fill in the form that pops up. Then click

Save

to store the contact in the favorites list.

Editing contact details

Click a contacts name followed by

Edit contact

Change the details in the form as appropriate and click

Save

Deleting a contact

Click a contacts name followed by

Edit contact

. Then click

Delete

to remove the entry from the favorites list.

* Note that only the first contact method will appear in the Favorites list on the Cisco TelePresence Touch controller. All contact methods are available when using the remote control.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Storing a contact in a folder

Choose the appropriate folder from the drop down list.

No folder means that the contact will be stored at the top level.

Adding a contact method*

You can store more than one contact method for each contact, e.g. video, telephone and mobile.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

Favorite list folders

The entries in the favorites list can be organized in folders.

System settings

Navigate to: Configuration > Favorites Management

Setting passwords

Administrator Guide

Appendices

Adding a folder

Click

Add folder

and fill in the form that pops up. Then click

Save

to create the folder.

Opening a folder

Click the folder name to open the folder and show its list of contacts.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Changing or Deleting a folder

Click

Edit folder

and update the information in the form that pops up.

Then click

Save

to store the changes

Click

Delete

to remove the folder and all its contacts and sub-folders.

Confirm your choice in the dialog that pops up.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

Choosing a wallpaper

You can choose from a set of predefined wallpapers to use as background on your display.

If you want the company logo or another custom picture as background on the main display, you may upload and use a custom wallpaper.

If you use the Touch controller: The custom wallpaper applies to only the main display and will not appear on the Touch controller.

System settings

Navigate to: Configuration > Personalization : Wallpaper tab

Setting passwords

Administrator Guide

Appendices

Uploading a custom wallpaper file

Click

Browse...

and locate your custom wallpaper image file.

The file format must be .png and the maximum image size is 1920 × 1200 pixels.

Click

Upload

to save the file on the video system.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Choosing a wallpaper

Choose a wallpaper from the list.

If you have uploaded a custom wallpaper, it will appear in the list together with the predefined wallpapers.

The chosen wallpaper is highlighted.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

Choosing a ringtone

You can choose from a set of predefined ringtones. The chosen ringtone can be played back from this page.

Even if the web interface is used to initiate the playback it is the video system that plays back the ringtone; it is not the PC running the web interface.

System settings

Navigate to: Configuration > Personalization : Ringtone tab

Setting passwords

Administrator Guide

Appendices

Choosing a ringtone

Choose a ringtone from the drop-down list, and click

Save

to make it the active ringtone.

Playing back a ringtone

Click the play button ( ► ) to play back the ringtone.

Use the stop button ( ) to end the playback.

You must save the ringtone before it can be played back.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

Peripherals overview

This page shows an overview of the video inputs and outputs, and the devices that are connected to the video system, for example camera(s), microphone(s), a Touch controller or

ISDN Link

System settings

Navigate to: Configuration > Peripherals

Setting passwords

Administrator Guide

Appendices

* The peripherals shown in the illustration serve as examples. Your system may have different peripherals and video input/output configurations.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Managing ISDN Link

If an ISDN Link is paired to the video system it can be managed from this page.

How to configure and use the ISDN Link are described in the ISDN Link documentation on

► http://www.cisco.com/go/isdnlink-docs

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

User administration

You can manage your video conference system’s user accounts from this page. You can create new users, edit the details of existing users, and delete users.

The default user account

The system comes with a default administrator user account with full access rights. The user name is admin and no password is set.

It is highly recommended to set a password for the

admin user.

chapter.

About user roles

A user account must hold one or a combination of several

user roles.

The following three user roles, with non-overlapping rights, exist:

• ADMIN: A user holding this role can create new users and change most settings. The user neither can upload audit certificates nor change the security audit settings.

• USER: A user holding this role can make calls and search the phone book. The user can modify a few settings, e.g. adjusting the audio volume and changing the menu language.

• AUDIT: A user holding this role can change the security audit configurations and upload audit certificates.

An administrator user account with full access rights, like the default admin user, must possess all the three roles.

Default user account

The system comes with

admin as the default user account. This user has full access rights.

System settings

Navigate to: Configuration > User Administration

Setting passwords

Administrator Guide

Appendices

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

User administration, continued

Creating a new user account

Follow these steps in order to create a new user account:

1. Click

Add new user...

2. Fill in the Username, Password and PIN code

, and check the appropriate user roles check boxes.

As a default the user has to change the password and

PIN code when signing in for the first time.

Do not fill in the Client Certificate DN (Distinguished

Name) field unless you want to use certificate login on https.

3. Set the Status to Active to activate the user.

4. Click

Create User

to save the changes.

Use the

Back

button to leave without making any changes.

System settings

Navigate to: Configuration > User Administration

Setting passwords

Administrator Guide

Appendices

The password is used with the web interface and command line interface; the PIN code is used with the remote control and on-screen menu when the Video OSD LoginRequired setting is switched On.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

User administration, continued

Changing user privileges

Follow these steps in order to change the user privileges:

1. Click the name of an existing user to open the Editing user window.

2. Check the appropriate user roles check boxes, decide if the user has to change the password and PIN code on the next sign in, and fill in the Client Certificate DN field if using certificate login on https.

3. Click

Update User

to save the changes.

Use the

Back

button to leave without making any changes.

Changing the password or PIN code

Follow these steps in order to change the password or PIN code

1. Click the name of an existing user to open the Editing user window.

2. Enter the new password or PIN code in the appropriate input fields.

3. Click

Change Password

Change PIN

to save the change.

Use the

Back

button to leave without making any changes.

System settings

Navigate to: Configuration > User Administration

Setting passwords

Administrator Guide

Appendices

The password is used with the web interface and command line interface; the PIN code is used with the remote control and on-screen menu when the Video OSD LoginRequired setting is switched On.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

User administration, continued

Deactivating a user account

Follow these steps in order to deactivate a user account:

Always keep at least one user with ADMIN rights

Active.

1. Click the name of an existing user to open the Editing user window.

2. Set the Status to Inactive.

3. Click

Update User

to save the changes.

Use the

Back

button to leave without making any changes.

Deleting a user account

Follow these steps in order to delete a user account:

It is not possible to delete the default admin user.

There must always be at least one user with ADMIN rights on the system.

1. Click the name of an existing user to open the Editing user window.

2. Click

Delete <user name>...

and confirm when prompted.

System settings

Navigate to: Configuration > User Administration

Setting passwords

Administrator Guide

Appendices

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

Adding a sign in banner

A sign in banner is a message that is shown to the user when signing in.

If a system administrator wants to provide initial information to all users, he can create a sign in banner. The message will be shown when the user signs in to the web interface or the command line interface.

System settings

Navigate to: Configuration > Sign In Banner

Setting passwords

Administrator Guide

Appendices

Adding a sign in banner

Enter the message that you want to present to the user when signing in, and click

Save

to activate the banner.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

Managing startup scripts

You can create one or more startup scripts

that will run every time the video system starts up.

A startup script contains commands (xCommand) and configurations (xConfiguration) that will be executed as part of the start up procedure. A few commands and configurations cannot be placed in a startup script, e.g.

xCommand Boot

. It is not possible to save a script containing illegal commands and configurations.

Syntax and semantics for xCommand and xConfiguration are explained in the API guide for the product.

If you have more than one startup script, they will run in the order from top to bottom of the list.

System settings

Navigate to: Configuration > Startup Scripts

Setting passwords

Administrator Guide

Appendices

Creating a startup script

1. Click

Create new...

2. Enter a name for your script in the title input filed.

3. Enter the commands (xConfiguration or xCommand) you want to issue in the command input field. Start each command on a new line.

4. Click

Save

* The script name and commands shown in the illustration serve as examples. You may make your own scripts.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

List of startup scripts

Startup scripts are listed here. A green dot appears next to an active script; a red ring appears next to an inactive script.

Running the script immediately

Select the script you want to run and click

Run

Running the script at every start up

Select the script you want to activate and click

Not running the script at start up

Select the script you want to deactivate and click

Off

Deleting a script

Select the script you want to delete and click

Delete

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

Application programming interface

The application programming interface (API) is a tool for integration professionals and developers working with this video system. The API is described in detail in the API guide for the system.

XML files

The XML files are part of the codec’s API. They structure information about the codec in a hierarchy.

• Configuration.xml contains the current system settings

(configuration). These settings are controlled from the web interface or from the API (Application Programmer

Interface).

• The information in status.xml is constantly updated by the system to reflect system and process changes. The status information is normally monitored from the API.

• Command.xml contains an overview of the commands available to instruct the system to perform an action. The commands are issued from the API.

• Valuespace.xml contains an overview of all the value spaces used in the system settings, status information, and commands.

API commands

Commands (xCommand) and configurations (xConfiguration) can be executed from this web page. Syntax and semantics are explained in the API guide for the product.

Navigate to: Configuration > API

System settings Setting passwords

Administrator Guide

Appendices

Opening an XML file

Click the file name to open the XML file.

Executing API commands

Enter a command, or a sequence of commands, in the text area and click

Execute

to issue the command(s).

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

Managing the video system’s certificates

Certificate validation may be required when using TLS

(Transport Layer Security).

A server or client may require that your video system presents a valid certificate to them before communication can be set up.

The video system’s certificates are text files that verify the authenticity of the system. These certificates may be issued by a certificate authority (CA).

The certificates are listed as shown in the illustration to the right

. They can be used for the following services: HTTPS,

SIP and IEEE 802.1X.

You can store several certificates on the system, but only one certificate can be used for each service at a time.

If authentication fails, the connection will not be established.

System settings

Navigate to: Configuration > Security: Certificates tab

Contact your system administrator to obtain the following file(s):

• Certificate (file format: .PEM)

• Private key, may be included in the same file as the certificate (file format: .PEM format)

• Password (required only if the private key is encrypted)

The certificate and the private key will be stored in the same file on the video system.

Adding a certificate

1. Click

Browse...

and find the Certificate and

Private key file(s) on your computer.

2. Fill in the

Password

if required.

3. Click

Add certificate...

to store the certificate on your system.

Setting passwords

Administrator Guide

Appendices

Enabling and disabling certificates

Use the buttons to switch a certificate on or off for the different services.

You can also view a certificate, and delete a certificate using the corresponding buttons.

* The certificates and certificate issuers shown in the illustration serve as examples. Your system may have other certificate(s).

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

Managing the list of trusted certificate authorities

Certificate validation may be required when using TLS

(Transport Layer Security).

Your video system may be set up to require that a server or client presents its certificate to the system before communication can be set up.

The certificates are text files that verify the authenticity of the server or client. The certificates must be signed by a trusted certificate authority (CA).

To be able to verify the signature of the certificates, a list of trusted CAs must reside on the video system. The certificates of the CAs are listed as shown in the illustration to the right

The list must include all CAs needed in order to verify certificates for HTTPS, SIP and IEEE 802.1X connections.

If the server cannot be authenticated, the connection will not be established.

System settings

Navigate to: Configuration > Security: CAs tab

Uploading a list of certificate authorities

The entries in a new file with CA certificates will be appended to the existing list, that is, the previously stored certificates will not be deleted. i. Click

Browse...

and find the file containing a list of CA certificates (file format: .PEM) on your computer.

ii. Click the

Add certificate authority...

to store the new CA certificate(s) on your system.

Contact your system administrator to obtain the CA certificate list (file format: .PEM).

Setting passwords

Administrator Guide

Appendices

Viewing and deleting certificates

You can view a certificate, and delete a certificate using the corresponding buttons.

* The certificate and certificate issuers shown in the illustration serve as examples. Your system will have other certificate(s).

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

Adding audit certificates

Audit logging records all sign in activity and configuration changes on your video system.

Audit logging is disabled by default, but you can enable it using the

Security > Audit > Logging > Mode

setting on the on-screen menu or the web interface.

In ExternalSecure audit logging mode the video system sends encrypted audit logs to an external audit server

(syslog server), which identity must be verified by a signed certificate.

To be able to verify the signature of the audit server certificates, a list of trusted audit certificate authorities (CAs) must reside on the video system.

If the audit server cannot be authenticated, the logs will not be sent.

Always upload the audit certificate list before enabling secure audit logging.

iii ii

System settings Setting passwords

Administrator Guide

Appendices

Navigate to: Configuration > Security: CAs tab / Configuration > System Configuration

1. Upload a list of audit server certificates

The entries in a new file with CA certificates will overwrite the existing list, that is, any previously stored audit certificates will be lost when you add a new file. i. Click

Browse...

and find the file containing the list of audit CA certificates (.PEM format) on your computer.

ii. Click

Add audit certificate

to store the certificate(s) on your system.

Contact your system administrator to obtain the Audit CA list (file format: .PEM).

2. Enable secure audit logging i. Go to the

System

Configuration

page and choose the

Security

category.

ii. Enter the

Address

of the audit server. If you choose Manual

PortAssignment,

you must also enter a

Port

number for the audit server. Click

Save

for the changes to take effect.

iii. Choose ExternalSecure from the

Logging Mode

drop-down list. Click

Save

for the change to take effect.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

Setting strong security mode

Strong security mode should be used only when compliance with DoD JITC regulations is required.

Read the provided information carefully before setting strong security mode.

Strong security mode sets very strict password requirements, and requires all users to change their password on the next sign in.

Software upload from TMS, web snapshots and calling from the web interface are prohibited in strong security mode.

System settings

Navigate to: Configuration > Security: Strong Security Mode tab

Setting passwords

Administrator Guide

Appendices

Setting strong security mode

Read carefully about the consequences of strong security mode before you continue.

1. If you want to use strong security mode, click

Enable strong security mode

Confirm your choice in the dialog box that appears.

The system will restart automatically.

2. Change the password when you are prompted. The new password must meet the strict criteria as described.

How to change the system password is described in the

► Setting passwords

section.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Return to normal mode

1. When in strong security mode, the system can be restored to normal mode by clicking

Disable strong security mode...

2. The system will restart automatically.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

Changing the persistency mode

By default, all persistency settings are set to Persistent. This means that configurations, call history, internal logs, local phonebook / favorites list and IP connectivity information are stored as normal. A system restart does not delete information.

As a general rule, we recommend NOT to change the default settings for persistency. But in the case were a new user is not supposed to see or trace back to any kind of logged information from the previous session, Nonpersistent mode must be used.

In order to clear/delete information that was stored before changing to Non-persistent mode, you should consider to factory reset the video system.

There is more information about performing a factory reset in the

► Factory resetting

appendix.

When in Non-persistent mode, the following information will be lost/cleared each time the system restarts:

• System Configuration changes that have been made since the last system restart.

• Information about calls that are placed or received since the last system restart (call history).

• Internal log files that has been made since the last system restart.

• Changes that are made to the local phonebook / favorites list since the last system restart.

• All IP related information (DHCP) from the last session.

Checking the persistency status

The radio buttons that are active when you open the

Security

page and go to the

Non-persistent Mode

tab, shows the current persistency status of the video system.

You can also see the status by checking

Security >

Persistency

on the

Configuration > System Status

page.

System settings

Navigate to: Configuration > Security: Non-persistent Mode tab

Changing the persistency settings

1. Set the persistency settings for the five categories as desired.

2. Click

Save and reboot...

The system will restart. After the restart, behavior according to the new persistency settings will start.

Note that logs, configurations etc. that was stored before you switch to Nonpersistent mode, will not be cleared or deleted.

Setting passwords

Administrator Guide

Appendices

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

Deleting trust lists (CUCM only)

The information on this page is only relevant for video systems that are registered to a Cisco Unified

Communications Manager (CUCM).

The web interface can be used to delete existing trust lists

(CTL and ITL) that are stored on the video system. Normally, you will not delete the old CTL and ITL files, but there are a few cases when you will need to delete them.

For more information about CUCM and trust lists, read the

Administering TC Endpoints on CUCM guide available on the

Cisco web site.

System settings

Navigate to: Configuration > Security: CUCM tab

Setting passwords

Administrator Guide

Appendices

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

Troubleshooting

The troubleshooting page lists the status for some common sources of errors. The list may be different for different products and installations

Note that critical issues and errors are clearly marked in red color; warnings are yellow.

System settings

Navigate to: Diagnostics > Troubleshooting

Setting passwords

Run diagnostics

Click

Re-run diagnostics

to make sure the information in the list is up-to-date.

Leave standby mode

This button is only visible when the system is in standby mode. If in standby mode, click

Deactivate standby

to wake up the system.

Administrator Guide

Appendices

* The messages shown in the illustration serve as examples. Your system may show other information.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

Downloading log files

The log files

are Cisco specific debug files which may be requested by the Cisco support organization if you need technical support.

The current log files are time stamped event log files.

All current log files are archived in a time stamped historical

log file each time the system restarts. If the maximum number of historical log files is reached, the oldest one will be overwritten.

About extended logging mode

Extended logging mode may be switched on to help diagnose network issues and problems during call setup. While in this mode more information is stored in the log files.

Note that extended logging uses more of your video system’s resources, and may cause your video system to underperform. You should only use extended logging mode when troubleshooting an issue.

System settings

Navigate to: Diagnostics > Log Files

Downloading all log files

Click

Download logs archive

and follow the instructions.

You can choose whether to include the call history in the archive or not; and you can choose whether to include the full call history or to make the caller/callee anonymous. Use the drop down list to include the preferred call history list.

Administrator Guide

Appendices Setting passwords

Start extended logging

1. Use the drop down list to choose the duration of extended logging.

2. Click

Start extended logging

You can stop the extended logging before it times out by clicking the

Stop extended logging

button that appears when extended logging is on.

Open/save one log file

Click the file name to open the log file in the web browser; right click to save the file on the computer.

* The log files shown in the illustration serve as examples. Your system may have other files.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

Upgrading the system software

This video conference system is using TC software. The version described in this document is TC7.0.

Contact your system administrator if you have questions about the software version.

Software release notes

For a complete overview of the news and changes, we recommend reading the Software Release Notes (TC7).

Go to: ► http://www.cisco.com/c/en/us/support/ collaboration-endpoints/telepresence-integrator-c-series/ tsd-products-support-series-home.html

New software

For software download, go to the

Cisco Download Software web page:

► http://www.cisco.com/cisco/software/navigator.html

Then navigate to your product.

The format of the file name is “s52000tc7_0_0.pkg” (each software version has a unique file name).

Release key

You need a valid release key to be able to use the video system. As from version TC6.1, any TC release key will do.

For older releases the release key is specific for each main release (e.g. TC4, TC5, TC6).

Normally, you do not need to install the release key yourself.

The release key is preserved when you upgrade from an earlier software version, and the release key is pre-installed on new systems. As from TC7.0, it is no longer possible to enter a release key from the web interface.

System settings

Navigate to: Maintenance > Software Upgrade

Setting passwords

Administrator Guide

Appendices

Adding option keys

An option key is required to activate optional functionality.

You may have several option keys in your system. If the keys are aready installed, you can skip this point and continue with the software installation.

If you do not have the required key(s), contact your Cisco representative to obtain them.

i. Enter an Option Key in the appropriate text input field and click

Add

If you have more than one option key, repeat this step for all keys.

Each system has unique keys, for example:

• 1R000-1-AA7A4A09

Installing new software

Download the appropriate software package from the Cisco

Software Download web page (see link to the left) and store it on your local computer. This is a .pkg file.

i. Click

Browse...

and find the downloaded .pkg file that contains the new software.

ii. Check the

Upgrade automatically after upload

check box, then click

Upload

to start the installation process straight away.

Keep the check box unchecked if you want to upload the software now and do the installation later.

The complete installation may take up to 30 minutes. You can follow the progress on the web page. The system restarts automatically after the installation.

You must sign in anew in order to continue working with the web interface after the restart.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

Backup and restore

All the system settings, which are available on the System configuration page, can be listed on-screen or stored as a text file (.tsh).

The .tsh file can be loaded back onto the system, thereby restoring the configuration.

System settings

Navigate to: Maintenance > Backup and Restore

Backing up or showing the current configuration

Click

Preview backup

to display the current settings on-screen.

Click

Take backup

to store the configuration as a text file.

Setting passwords

Administrator Guide

Appendices

Restoring an earlier configuration

Click

Browse...

and find the file with the configuration you want to restore.

Click

Restore

to reconfigure the system as defined in the file.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

System recovery: Revert to the previously used software version

If there is a severe problem with the video system, switching to the previously used software version may help solving the problem. The previously used software image still resides on the system, so you do not have to download the software again.

Reverting to the previously used software version should only be done by a system administrator or in contact with Cisco technical support.

We strongly recommend that you backup your system’s log files and configuration before you swap to the other software image.

System settings Setting passwords

Navigate to: Maintenance > System Recovery : Backup tab and Software Recovery Swap tab

Administrator Guide

Appendices

1. Backing up log files and system configuration

We recommend that you backup your system’s log files and configuration before you swap to the other software image.

Click

Download Logs

and

Download

Configuration Backup

and follow the instructions to save the files on your computer.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

2. Reverting to the previously used software version

1. Revert to the previously used software version by clicking

Switch to software

TCx.y.z...

, where x.y.z indicates the software version.

2. Click

Yes

to confirm your choice, or

Cancel

if you have changed your mind.

Wait while the system resets. The system will restart automatically when finished.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

System recovery: Factory reset

If there is a severe problem with the video system, the last resort may be to reset it to its default factory settings. Always consider reverting to the previously used software image before performing a factory reset. In many situations this will recover the system

A factory reset should only be performed by a system administrator or in contact with Cisco technical support.

When factory resetting the video system the following happens:

• The call logs will be deleted.

• Passwords will be reset to default.

• All system parameters will be reset to default values.

• All files that have been uploaded to the system will be deleted. This includes, but is not limited to, custom backgrounds, certificates, and the favorites list (My contacts).

• The previous (inactive) software image will be deleted.

• Release keys and option keys will not be affected.

The system restarts automatically after the reset. It is using the same software image as before.

We strongly recommend that you backup your system’s log files and configuration before you perform a factory reset.

It is not possible to undo a factory reset.

There is more information about performing a factory reset in the

► Factory resetting appendix.

System settings

Navigate to: Maintenance > System Recovery : Backup tab and Factory Reset tab

1. Backing up log files and system configuration

We strongly recommend that you backup your system’s log files and configuration before you perform a factory reset; otherwise these data will be lost.

Click

Download Logs

and

Download

Configuration Backup

and follow the instructions to save the files on your computer.

Setting passwords

Administrator Guide

Appendices

2. Performing a factory reset

Read the provided information carefully before you restore the factory settings by clicking

Perform a factory reset...

Click

Yes

to confirm your choice, or

Cancel

if you have changed your mind.

Wait while the system resets. The system will restart automatically when finished.

* Read about software swapping in the

► System recovery: Revert to the previously used software version

section.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction

Restarting the system

The system can be shut down or restarted remotely using the web interface.

Navigate to: Maintenance > Restart

System settings

Restarting the system

Click

Restart TelePresence device...

to restart the system.

It will take a few minutes before the system is ready for use.

Setting passwords

Shutting down the system

Click

Shutdown TelePresence device...

to shut down the system.

The system cannot be turned on again remotely; you must press its power button physically to turn it on.

Administrator Guide

Appendices

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface Setting passwords

Administrator Guide

Appendices

Chapter 3

System settings

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface Setting passwords

Administrator Guide

Appendices

Overview of the system settings

In the following pages you will find a complete list of the system settings which are configured from the

System

Configuration

page on the web interface. The examples show either the default value or an example of a value.

Open a web browser and enter the IP address of the video system; then sign in.

To find the IP address (IPv4 or IPv6), open the

Settings

menu on the Touch controller and tap

System Information

; or navigate to

Home > Settings >

System information

when using a remote control and the on-screen menu.

* The

Settings

menu can be accessed from the drop down window that appears when you tap the contact information in the upper, left corner of the Touch controller.

Audio settings ....................................................................... 60

Audio Input HDMI [2] Level ...................................................... 60

Audio Input HDMI [2] Mode ..................................................... 60

Audio Input HDMI [2] VideoAssociation

MuteOnInactiveVideo .............................................................. 60

Audio Input HDMI [2] VideoAssociation VideoInputSource ..... 60

Audio Input Line [1..2] Channel.................................................61

Audio Input Line [1..2] Equalizer ID .......................................... 60

Audio Input Line [1..2] Equalizer Mode .................................... 60

Audio Input Line [1..2] Level .....................................................61

Audio Input Line [1..2] LoopSuppression .................................61

Audio Input Line [1..2] Mode .....................................................61

Audio Input Line [1..2] VideoAssociation

MuteOnInactiveVideo ...............................................................61

Audio Input Line [1..2] VideoAssociation VideoInputSource ....61

Audio Input Microphone [1..2]/[1..4] EchoControl

Dereverberation ...................................................................... 62

Audio Input Microphone [1..2]/[1..4] EchoControl Mode .......... 62

Audio Input Microphone [1..2]/[1..4] EchoControl

NoiseReduction ....................................................................... 62

Audio Input Microphone [1..2]/[1..4] Equalizer ID ..................... 62

Audio Input Microphone [1..2]/[1..4] Equalizer Mode ............... 62

Audio Input Microphone [1..2]/[1..4] Level ............................... 63

Audio Input Microphone [1..2]/[1..4] Mode .............................. 63

Audio Input Microphone [1..2]/[1..4] Type ................................ 63

Audio Input Microphone [1..2]/[1..4] VideoAssociation

MuteOnInactiveVideo .............................................................. 63

Audio Input Microphone [1..2]/[1..4] VideoAssociation

VideoInputSource ................................................................... 63

Audio Microphones Mute Enabled .......................................... 65

Audio Output HDMI [1] Level ................................................... 63

Audio Output HDMI [1] Mode .................................................. 64

Audio Output Line [1..2] Channel............................................. 64

Audio Output Line [1..2] Equalizer ID ....................................... 64

Audio Output Line [1..2] Equalizer Mode ................................. 64

Audio Output Line [1..2] Level ................................................. 64

Audio Output Line [1..2] Mode ................................................. 64

Audio Output Line [1] Type ...................................................... 64

Audio Output Line [2] Type ...................................................... 65

Audio SoundsAndAlerts KeyTones Mode ............................... 65

Audio SoundsAndAlerts RingTone .......................................... 65

Audio SoundsAndAlerts RingVolume...................................... 65

Audio Volume .......................................................................... 65

Cameras settings .................................................................. 66

Cameras Camera [1..7] Backlight ............................................ 66

Cameras Camera [1..7] Brightness Level ................................ 66

Cameras Camera [1..7] Brightness Mode ............................... 66

Cameras Camera [1..7] DHCP ................................................. 68

Cameras Camera [1..7] Flip ..................................................... 66

Cameras Camera [1..7] Focus Mode ....................................... 66

Cameras Camera [1..7] Gamma Level ..................................... 67

Cameras Camera [1..7] Gamma Mode .................................... 67

Cameras Camera [1..7] IrSensor ............................................. 67

Cameras Camera [1..7] Mirror ................................................. 67

Cameras Camera [1..7] MotorMoveDetection ......................... 67

Cameras Camera [1..7] Whitebalance Level ........................... 68

Cameras Camera [1..7] Whitebalance Mode .......................... 68

Conference settings ............................................................. 69

Conference [1..1] AutoAnswer Delay ....................................... 69

Conference [1..1] AutoAnswer Mode ...................................... 69

Conference [1..1] AutoAnswer Mute ........................................ 69

Conference [1..1] CallProtocolIPStack ..................................... 69

Conference [1..1] DefaultCall Protocol ..................................... 70

Conference [1..1] DefaultCall Rate ............................................71

Conference [1..1] DoNotDisturb DefaultTimeout ..................... 70

Conference [1..1] DoNotDisturb Mode .................................... 69

Conference [1..1] Encryption Mode ......................................... 70

Conference [1..1] FarEndControl Mode ................................... 70

Conference [1..1] FarEndControl SignalCapability ................... 70

Conference [1..1] IncomingMultisiteCall Mode ........................ 73

Conference [1..1] MaxReceiveCallRate ....................................71

Conference [1..1] MaxTotalReceiveCallRate .............................71

Conference [1..1] MaxTotalTransmitCallRate ............................71

Conference [1..1] MaxTransmitCallRate ....................................71

Conference [1..1] MicUnmuteOnDisconnect Mode ................. 69

Conference [1..1] Multipoint Mode .......................................... 73

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

Administrator Guide

Appendices Setting passwords

Conference [1..1] Presentation OnPlacedOnHold ................... 72

Conference [1..1] Presentation Policy ...................................... 72

Conference [1..1] Presentation RelayQuality ........................... 72

Conference [1..1] VideoBandwidth MainChannel Weight ........ 72

Conference [1..1] VideoBandwidth Mode ................................ 72

Conference [1..1] VideoBandwidth PresentationChannel

Weight ..................................................................................... 72

FacilityService settings ..........................................................74

FacilityService Service [1..5] CallType .....................................74

FacilityService Service [1..5] Name .........................................74

FacilityService Service [1..5] Number ......................................74

FacilityService Service [1..5] Type ...........................................74

GPIO settings ........................................................................ 75

GPIO Pin [1..4] Mode ............................................................... 75

H323 settings ........................................................................ 76

H323 NAT Address ................................................................. 76

H323 NAT Mode ..................................................................... 76

H323 Profile [1..1] Authentication LoginName ......................... 76

H323 Profile [1..1] Authentication Mode .................................. 76

H323 Profile [1..1] Authentication Password ........................... 77

H323 Profile [1..1] CallSetup Mode .......................................... 77

H323 Profile [1..1] Gatekeeper Address .................................. 77

H323 Profile [1..1] Gatekeeper Discovery ................................ 77

H323 Profile [1..1] H323Alias E164 .......................................... 77

H323 Profile [1..1] H323Alias ID ............................................... 77

H323 Profile [1..1] PortAllocation ............................................. 78

Logging settings ................................................................... 79

Logging Mode ......................................................................... 79

Network settings ................................................................... 80

Network [1..1] DHCP RequestTFTPServerAddress ..................81

Network [1..1] DNS Domain Name ............................................81

Network [1..1] DNS Server [1..3] Address .................................81

Network [1..1] IEEE8021X AnonymousIdentity ......................... 84

Network [1..1] IEEE8021X Eap Md5 ......................................... 84

Network [1..1] IEEE8021X Eap Peap ........................................ 85

Network [1..1] IEEE8021X Eap Tls ............................................ 85

Network [1..1] IEEE8021X Eap Ttls ........................................... 85

Network [1..1] IEEE8021X Identity ............................................ 84

Network [1..1] IEEE8021X Mode .............................................. 83

Network [1..1] IEEE8021X Password ........................................ 84

Network [1..1] IEEE8021X TlsVerify .......................................... 84

Network [1..1] IEEE8021X UseClientCertificate ....................... 84

Network [1..1] IPStack .............................................................. 80

Network [1..1] IPv4 Address .................................................... 80

Network [1..1] IPv4 Assignment ............................................... 80

Network [1..1] IPv4 Gateway .................................................... 80

Network [1..1] IPv4 SubnetMask .............................................. 80

Network [1..1] IPv6 Address .....................................................81

Network [1..1] IPv6 Assignment ............................................... 80

Network [1..1] IPv6 DHCPOptions ............................................81

Network [1..1] IPv6 Gateway .....................................................81

Network [1..1] MTU .................................................................. 85

Network [1..1] QoS Diffserv Audio ........................................... 82

Network [1..1] QoS Diffserv Data ............................................. 82

Network [1..1] QoS Diffserv ICMPv6 ....................................... 83

Network [1..1] QoS Diffserv NTP ............................................. 83

Network [1..1] QoS Diffserv Signalling ..................................... 83

Network [1..1] QoS Diffserv Video ........................................... 82

Network [1..1] QoS Mode ........................................................ 82

Network [1..1] RemoteAccess Allow ........................................ 86

Network [1..1] Speed ............................................................... 85

Network [1..1] TrafficControl Mode .......................................... 85

Network [1..1] VLAN Voice Mode ............................................ 86

Network [1..1] VLAN Voice VlanId............................................ 86

NetworkPort settings ............................................................ 87

NetworkPort [2] Mode ............................................................. 87

NetworkServices settings ..................................................... 88

NetworkServices CTMS Encryption ........................................91

NetworkServices CTMS Mode ................................................91

NetworkServices H323 Mode ................................................ 88

NetworkServices HTTP Mode ................................................ 88

NetworkServices HTTPS Mode .............................................. 89

NetworkServices HTTPS OCSP Mode ................................... 89

NetworkServices HTTPS OCSP URL ..................................... 90

NetworkServices HTTPS VerifyClientCertificate .................... 89

NetworkServices HTTPS VerifyServerCertificate .................. 89

NetworkServices MultiWay Address ...................................... 89

NetworkServices MultiWay Protocol ...................................... 89

NetworkServices NTP Address .............................................. 90

NetworkServices NTP Mode .................................................. 90

NetworkServices SIP Mode .................................................... 88

NetworkServices SNMP CommunityName ............................ 90

NetworkServices SNMP Host [1..3] Address .......................... 90

NetworkServices SNMP Mode ............................................... 90

NetworkServices SNMP SystemContact ................................91

NetworkServices SNMP SystemLocation ...............................91

NetworkServices SSH AllowPublicKey ....................................91

NetworkServices SSH Mode ...................................................91

NetworkServices Telnet Mode ............................................... 88

NetworkServices WelcomeText .............................................. 88

NetworkServices XMLAPI Mode ............................................ 88

Phonebook settings .............................................................. 92

Phonebook Server [1..1] ID ...................................................... 92

Phonebook Server [1..1] Type ................................................. 92

Phonebook Server [1..1] URL .................................................. 92

Provisioning settings ............................................................. 93

Provisioning Connectivity ....................................................... 93

Provisioning ExternalManager Address .................................. 94

Provisioning ExternalManager AlternateAddress.................... 94

Provisioning ExternalManager Domain ................................... 94

Provisioning ExternalManager Path ........................................ 94

Provisioning ExternalManager Protocol .................................. 94

Provisioning HttpMethod ........................................................ 93

Provisioning LoginName ......................................................... 93

Provisioning Mode .................................................................. 93

Provisioning Password ............................................................ 93

RTP settings .......................................................................... 95

RTP Ports Range Start ............................................................ 95

RTP Ports Range Stop ............................................................ 95

Security settings ................................................................... 96

Security Audit Logging Mode ................................................. 96

Security Audit OnError Action ................................................. 96

Security Audit Server Address ............................................... 96

Security Audit Server Port ...................................................... 96

Security Audit Server PortAssignment ................................... 96

Security Session InactivityTimeout ......................................... 97

Security Session ShowLastLogon .......................................... 97

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

Administrator Guide

Appendices Setting passwords

SerialPort settings ................................................................ 98

SerialPort BaudRate ................................................................ 98

SerialPort LoginRequired ........................................................ 98

SerialPort Mode ...................................................................... 98

SIP settings ........................................................................... 99

SIP ANAT ................................................................................ 99

SIP AuthenticateTransferror .................................................... 99

SIP ListenPort ......................................................................... 99

SIP OCSP DefaultResponder .................................................. 99

SIP OCSP Mode...................................................................... 99

SIP PreferredIPMedia .............................................................. 99

SIP PreferredIPSignaling ......................................................... 99

SIP Profile [1..1] Authentication [1..1] LoginName ...................101

SIP Profile [1..1] Authentication [1..1] Password ......................101

SIP Profile [1..1] DefaultTransport ...........................................101

SIP Profile [1..1] DisplayName.................................................101

SIP Profile [1..1] Ice DefaultCandidate ................................... 100

SIP Profile [1..1] Ice Mode ...................................................... 100

SIP Profile [1..1] Line .............................................................. 102

SIP Profile [1..1] Mailbox ........................................................ 102

SIP Profile [1..1] Outbound ..................................................... 102

SIP Profile [1..1] Proxy [1..4] Address ..................................... 102

SIP Profile [1..1] Proxy [1..4] Discovery .................................. 102

SIP Profile [1..1] TlsVerify ........................................................101

SIP Profile [1..1] Turn BandwidthProbe .................................. 100

SIP Profile [1..1] Turn DiscoverMode ..................................... 100

SIP Profile [1..1] Turn DropRflx ............................................... 100

SIP Profile [1..1] Turn Password ..............................................101

SIP Profile [1..1] Turn Server .................................................. 100

SIP Profile [1..1] Turn UserName ........................................... 100

SIP Profile [1..1] Type ............................................................. 102

SIP Profile [1..1] URI ................................................................101

Standby settings ..................................................................103

Standby BootAction .............................................................. 103

Standby Control .................................................................... 103

Standby Delay ....................................................................... 103

Standby StandbyAction ........................................................ 103

Standby WakeupAction ......................................................... 103

SystemUnit settings ............................................................ 104

SystemUnit CallLogging Mode ............................................. 104

SystemUnit ContactInfo Type ............................................... 104

SystemUnit IrSensor ............................................................. 105

SystemUnit MenuLanguage .................................................. 104

SystemUnit Name ................................................................. 104

Time settings ...................................................................... 106

Time DateFormat .................................................................. 106

Time TimeFormat .................................................................. 106

Time Zone ............................................................................. 106

UserInterface settings ..........................................................107

UserInterface TouchPanel DefaultPanel ................................107

UserInterface UserPreferences .............................................107

Video settings ..................................................................... 108

Video AllowWebSnapshots ................................................... 108

Video CamCtrlPip CallSetup Duration .................................. 108

Video CamCtrlPip CallSetup Mode ....................................... 108

Video DefaultPresentationSource ......................................... 108

Video Input DVI [3]/[2,3] RGBQuantizationRange .................. 108

Video Input DVI [3]/[2,3] Type ................................................ 109

Video Input HDMI [1..2] RGBQuantizationRange ................... 109

Video Input Source [1..3] CameraControl CameraId .............. 111

Video Input Source [1..3] CameraControl Mode .................... 111

Video Input Source [1..3] Name ............................................ 109

Video Input Source [1..3] OptimalDefinition Profile ................ 111

Video Input Source [1..3] OptimalDefinition

Threshold60fps ......................................................................112

Video Input Source [1..3] PresentationSelection ....................110

Video Input Source [1..3] Quality ............................................112

Video Input Source [1..3] Type ...............................................110

Video Input Source [1..3] Visibility ..........................................110

Video Input Source [1] Connector ......................................... 109

Video Input Source [2] Connector ......................................... 109

Video Input Source [3] Connector..........................................110

Video Layout DisableDisconnectedLocalOutputs ..................112

Video Layout Engine LocalMode ...........................................112

Video Layout LocalLayoutFamily ...........................................113

Video Layout PresentationDefault View .................................113

Video Layout RemoteLayoutFamily ........................................113

Video Layout ScaleToFrame ..................................................114

Video Layout ScaleToFrameThreshold ...................................114

Video Layout Scaling .............................................................113

Video MainVideoSource ........................................................112

Video Monitors .......................................................................116

Video OSD AutoSelectPresentationSource ...........................118

Video OSD CallSettingsSelection ..........................................118

Video OSD EncryptionIndicator .............................................117

Video OSD InputMethod Cyrillic ............................................119

Video OSD InputMethod InputLanguage ...............................119

Video OSD LanguageSelection .............................................117

Video OSD LoginRequired .....................................................119

Video OSD MenuStartupMode ..............................................117

Video OSD MissedCallsNotification .......................................117

Video OSD Mode ...................................................................116

Video OSD MyContactsExpanded .........................................118

Video OSD Output .................................................................118

Video OSD TodaysBookings ..................................................118

Video OSD VirtualKeyboard ...................................................117

Video OSD WallpaperSelection .............................................116

Video Output Composite [3] MonitorRole ..............................121

Video Output Composite [3] OverscanLevel ..........................122

Video Output Composite [3] Resolution .................................122

Video Output DVI [2] MonitorRole ..........................................121

Video Output DVI [2] OverscanLevel ......................................121

Video Output DVI [2] Resolution .............................................121

Video Output DVI [2] RGBQuantizationRange ........................120

Video Output HDMI [1] CEC Mode .........................................119

Video Output HDMI [1] MonitorRole .......................................120

Video Output HDMI [1] OverscanLevel ...................................120

Video Output HDMI [1] Resolution ..........................................120

Video Output HDMI [1] RGBQuantizationRange .....................119

Video PIP ActiveSpeaker DefaultValue Position ....................114

Video PIP Presentation DefaultValue Position .......................114

Video Selfview .......................................................................115

Video SelfviewDefault FullscreenMode .................................115

Video SelfviewDefault Mode ..................................................115

Video SelfviewDefault OnMonitorRole ...................................116

Video SelfviewDefault PIPPosition .........................................116

Video SelfviewPosition ..........................................................115

Video WallPaper.....................................................................122

Experimental settings ..........................................................123

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface Setting passwords

Audio settings

Audio Input HDMI [2] Mode

Determine if the audio channels on the HDMI input shall be enabled. The HDMI input 2 has two audio channels.

Requires user role: ADMIN

Value space: <Off/On>

Off: Disable audio on the HDMI input.

On: Enable audio on the HDMI input.

Example:

Audio Input HDMI 2 Mode: On

Audio Input HDMI [2] Level

Define the audio level of the HDMI input connector, in steps of 1 dB.

See the Audio Level tables in the Physical Interfaces Guide for the codec for a complete overview of the menu values represented in dB.

Requires user role: ADMIN

Value space: <-24..0>

Range: Select a value from -24 to 0 dB.

Example:

Audio Input HDMI 2 Level: 0

Audio Input HDMI [2] VideoAssociation MuteOnInactiveVideo

Enable association of a video source to an HDMI audio input.

Administrator Guide

Appendices

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface Setting passwords

Administrator Guide

Appendices

Set the audio input line mode.

Requires user role: ADMIN

Value space: <Off/On>

Off: Disable the Audio Line input.

On: Enable the Audio Line input.

Example:

Audio Input Line 1 Mode: On

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

Audio Input Microphone [1..2]/[1..4] EchoControl Mode

NOTE: Codec C40 has two microphone connectors. Codec C60 has four microphone connectors.

The echo canceller continuously adjusts itself to the audio characteristics of the room and compensate for any changes it detects in the audio environment. If the changes in the audio conditions are very significant the echo canceller may take a second or two to re-adjust.

Requires user role: ADMIN

Value space: <Off/On>

Off: Echo Control should be switched Off if external echo cancellation or playback equipment is used.

On: Echo Control is normally set to On to prevent the far end from hearing their own audio.

Once selected, echo cancellation is active at all times.

Example:

Audio Input Microphone 1 EchoControl Mode: On

Audio Input Microphone [1..2]/[1..4] EchoControl NoiseReduction

NOTE: Codec C40 has two microphone connectors. Codec C60 has four microphone connectors.

The system has a built-in noise reduction which reduces constant background noise (for example noise from air-conditioning systems, cooling fans etc.). In addition, a high pass filter

(Humfilter) reduces very low frequency noise. Requires the Echo Control Mode to be enabled for the microphone.

Requires user role: ADMIN

Value space: <Off/On>

Off: Turn off the Noise Reduction.

On: The Noise Reduction should be enabled in the presence of low frequency noise.

Example:

Audio Input Microphone 1 EchoControl NoiseReduction: On

Administrator Guide

Appendices Setting passwords

Audio Input Microphone [1..2]/[1..4] EchoControl Dereverberation

NOTE: Codec C40 has two microphone connectors. Codec C60 has four microphone connectors.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface Setting passwords

Administrator Guide

Appendices

Audio Input Microphone [1..2]/[1..4] VideoAssociation MuteOnInactiveVideo

NOTE: Codec C40 has two microphone connectors. Codec C60 has four microphone connectors.

Audio Input Microphone [1..2]/[1..4] Mode

NOTE: Codec C40 has two microphone connectors. Codec C60 has four microphone connectors.

Set the audio input microphone mode.

Requires user role: ADMIN

Value space: <Off/On>

Off: Disable the microphone connector.

On: Enable the microphone connector.

Example:

Audio Input Microphone 1 Mode: On

Audio Input Microphone [1..2]/[1..4] Type

NOTE: Codec C40 has two microphone connectors. Codec C60 has four microphone connectors.

The microphone connectors are intended for electret type microphones. The microphone connector can be set to line or microphone mode.

Requires user role: ADMIN

Value space: <Microphone/Line>

Microphone: Select Microphone when you have 48 V Phantom voltage and the preamplification is On.

Line: Select Line when you have a standard balanced line input. The phantom voltage and pre-amplification is Off.

Example:

Audio Input Microphone 1 Type: Line

Audio Output HDMI [1] Level

Define the output level of the HDMI output connector, in steps of 1 dB.

See the Audio Level tables in the Physical Interfaces Guide for the codec for a complete overview of the menu values represented in dB.

Requires user role: ADMIN

Value space: <-24..0>

Range: Select a value from -24 to 0dB.

Example:

Audio Output HDMI 1 Level: 0

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

Audio Output HDMI [1] Mode

Determine if the audio channel on the HDMI output connector shall be enabled.

Requires user role: ADMIN

Value space: <Off/On>

Off: Disable the audio channel on the HDMI output.

On: Enable the audio channel on the HDMI output.

Example:

Audio Output HDMI 1 Mode: On

Audio Output Line [1..2] Channel

Define whether the Audio Line output is a mono signal or part of a multichannel signal.

Requires user role: ADMIN

Administrator Guide

Appendices Setting passwords

Audio Output Line 1 Type: Auto

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface Setting passwords

Administrator Guide

Appendices

Audio Output Line [2] Type

Line output 2 is a dedicated analog output, hence type can be set to analog only.

Requires user role: ADMIN

Value space: <Analog>

Analog: Can be set to analog only.

Example:

Audio Output Line 2 Type: Analog

Audio Microphones Mute Enabled

Determine whether audio-mute is allowed or not. The default value is True.

Requires user role: ADMIN

Value space: <True/InCallOnly>

True: Muting of audio is always available.

InCallOnly: Muting of audio is only available when the device is in a call. When Idle it is not possible to mute the microphone. This is useful when an external telephone service/audio system is connected via the codec and is to be available when the codec is not in a call.

When set to InCallOnly this will prevent the audio-system from being muted by mistake.

Example:

Audio Microphones Mute Enabled: True

Audio SoundsAndAlerts KeyTones Mode

The system can be configured to make a keyboard click sound effect (key tone) when pressing a key on the remote control, or when typing text or numbers on the Touch screen control panel.

Requires user role: USER

Value space: <Off/On>

Off: No key tones will be played when you type.

On: You will hear a key tone when you press a key or type text.

Example:

Audio SoundsAndAlerts KeyTones Mode: Off

Audio SoundsAndAlerts RingTone

When using the Touch screen control panel: Choose a ringtone from the list. If the setting

UserInterface UserPreferences has been set to On, the Ringtone setting is available from the

Settings menu. If the setting UserInterface UserPreferences has been set to Off, the Ringtone setting is available from the Administrator settings, and you must login with username and password.

When using the on-screen menus and a remote control: Choose a ringtone from the list

When using the web interface: Enter the name of the ringtone for incoming calls. To see the list of valid ringtones, navigate to Configuration > Personalization > Ringtone > Select active ringtone.

When using a command line interface (API): Enter the name of the ringtone for incoming calls. To see the list of valid ringtones, run the following API command: xCommand Audio

Example:

Cameras Camera 1 Brightness Level: 1

Setting passwords

Administrator Guide

Appendices

Cameras Camera [1..7] Flip

With Flip mode (vertical flip) you can flip the image upside down.

Requires user role: ADMIN

Value space: <Auto/Off/On>

Auto: When the camera is placed upside down the image is automatically flipped upside down. This setting will only take effect for a camera that automatically detects which way it is mounted.

Off: Display the video on screen the normal way.

On: When enabled the video on screen is flipped. This setting is used when a camera is mounted upside down, but cannot automatically detect which way it is mounted.

Example:

Cameras Camera 1 Flip: Off

Cameras Camera [1..7] Focus Mode

Set the camera focus mode.

Requires user role: ADMIN

Value space: <Auto/Manual>

Auto: The camera will auto focus once a call is connected, as well as after moving the camera (pan, tilt, zoom). The system will use auto focus only for a few seconds to set the right focus; then auto focus is turned off to prevent continuous focus adjustments of the camera.

Manual: Turn the autofocus off and adjust the camera focus manually.

Example:

Cameras Camera 1 Focus Mode: Auto

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

Cameras Camera [1..7] Gamma Mode

Applies to cameras which support gamma mode. Gamma describes the nonlinear relationship between image pixels and monitor brightness. The Cisco TelePresence PrecisionHD 720p camera supports gamma mode. The PrecisionHD 1080p camera does not support gamma mode.

Requires user role: ADMIN

Administrator Guide

Appendices Setting passwords

Cameras Camera [1..7] Mirror

With Mirror mode (horizontal flip) you can mirror the image on screen.

Requires user role: ADMIN

Value space: <Auto/Off/On>

Auto: When the camera is placed upside down the image is automatically mirrored. Use this setting with cameras that can be mounted upside down, and that can auto detect that the camera is mounted upside down.

Off: See the self-view in normal mode, that is the experience of self-view is as seeing yourself as other people see you.

On: See the self-view in mirror mode, that is the self-view is reversed and the experience of self-view is as seeing yourself in a mirror.

Example:

Cameras Camera 1 Mirror: Off

Cameras Camera [1..7] MotorMoveDetection

This setting applies only when using a Cisco TelePresence PrecisionHD 1080p12x camera.

If adjusting the camera position by hand you can configure whether the camera should keep its new position or return to the preset or position it had before.

Requires user role: ADMIN

Value space: <Off/On>

Off: When the camera position is adjusted manually the camera will keep this position until adjusted again. WARNING: If moving the camera by hand, the camera will not register the new pan and tilt values since there is no position feedback. This will result in wrong pan and tilt values when recalling the camera presets subsequently.

On: When the camera position is adjusted manually, or the camera detects that the motors have moved, it will first re-initialize (i.e. go to default position) then return to the preset/ position it had before the camera was adjusted.

Example:

Cameras Camera 1 MotorMoveDetection: Off

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Setting passwords

Administrator Guide

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

Conference settings

Conference [1..1] CallProtocolIPStack

Select if the system should enable IPv4, IPv6, or dual IP stack on the call protocol (SIP, H323).

Setting passwords

Administrator Guide

Appendices

Conference [1..1] AutoAnswer Delay

Appendices

> In Point to point calls: If the far end system supports encryption (AES-128), the call will be encrypted. If not, the call will proceed without encryption.

> In MultiSite calls: In order to have encrypted MultiSite conferences, all sites must support encryption. If not, the conference will be unencrypted.

Example:

Conference 1 Encryption Mode: BestEffort

Conference [1..1] DefaultCall Protocol

Set the Default Call Protocol to be used when placing calls from the system.

Requires user role: ADMIN

Value space: <Auto/H323/Sip/H320>

Auto: Enables auto-selection of the call protocol based on which protocols are available.

If multiple protocols are available, the order of priority is: 1) SIP; 2) H323; 3) H320. If the system cannot register, or the call protocol is not enabled, the auto-selection chooses H323.

H323: H323 ensures that calls are set up as H.323 calls.

Sip: Sip ensures that calls are set up as SIP calls.

H320: H320 ensures that calls are set up as H.320 calls (only applicable if connected to a

Cisco TelePresence ISDN Link gateway).

Example:

Conference 1 DefaultCall Protocol: H323

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface Setting passwords

Administrator Guide

Appendices

Range: Select a value between 64 and 10000.

Example:

Conference 1 MaxTotalTransmitCallRate: 10000

Conference [1..1] MaxTotalReceiveCallRate

This configuration applies when using a video system's built-in MultiSite feature (optional) to host a multipoint video conference.

Specify the maximum overall receive bit rate allowed. The bit rate will be divided fairly among all active calls at any time. This means that the individual calls will be up-speeded or downspeeded as appropriate when someone leaves or enters a multipoint conference, or when a call is put on hold (suspended) or resumed.

The maximum receive bit rate for each individual call is defined in the Conference

MaxReceiveCallRate setting.

Requires user role: ADMIN

Value space: <64..10000>

Range: Select a value between 64 and 10000.

Example:

Conference 1 Presentation RelayQuality: Sharpness

Conference [1..1] Presentation OnPlacedOnHold

Define whether or not to continue sharing a presentation after the remote site has put you on hold.

Requires user role: ADMIN

Value space: <Stop/NoAction>

Stop: The video system stops the presentation sharing when the remote site puts you on hold. The presentation will not continue when the call is resumed.

NoAction: The video system will not stop the presentation sharing when put on hold. The presentation will not be shared while you are on hold, but it will continue automatically when the call is resumed.

Example:

Conference 1 Presentation OnPlacedOnHold: NoAction

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface Setting passwords

Administrator Guide

Appendices

Conference [1..1] Multipoint Mode

Define how the video system handles multiparty video conferences.

If registered to a Cisco TelePresence Video Communication Server (VCS), the video system can either use its own built-in MultiSite feature, or it can rely on the MultiWay network solution.

MultiWay requires that the video network includes a multipoint control unit (MCU).

If registered to a Cisco Unified Communications Manager (CUCM) version 8.6.2 or newer, the video system can use either the CUCM conference bridge, or the video system's own built-in

MultiSite feature. Which one to use is set-up by CUCM.

Both Multiway and the CUCM conference bridge allows you to set up conferences with many participants. The built-in MultiSite allows up to four participants (yourself included) plus one additional audio call.

Note that the built-in MultiSite is optional and may not be available on all video systems.

Requires user role: ADMIN

Value space: <Auto/Off/MultiSite/MultiWay/CUCMMediaResourceGroupList>

Auto: The multipoint method available will be choosen automatically; if none are available the

Multipoint Mode will automatically be set to Off. If both MultiWay and MultiSite are available, the MultiWay service takes priority over the built-in MultiSite.

Off: Multiparty conferences are not allowed.

MultiSite: Multiparty conferences are set up using the built-in MultiSite feature. If MultiSite is chosen when the MultiSite feature is not available, the Multipoint Mode will automatically be set to Off.

MultiWay: Multiparty conferences are set up using the MultiWay service. If MultiWay is chosen when the MultiWay service is not available, the Multipoint Mode will automatically be set to Off. This may occur when the NetworkServices MultiWay Address setting is empty or not properly set.

CUCMMediaResourceGroupList: Multiparty conferences (ad hoc conferences) are hosted by the CUCM configured conference bridge. This setting is provisioned by CUCM in a CUCM environment and should never be set manually by the user.

Example:

Conference 1 Multipoint Mode: Auto

Conference [1..1] IncomingMultisiteCall Mode

Select whether or not to allow incoming calls when already in a call/conference.

Requires user role: ADMIN

Value space: <Allow/Deny>

Allow: You will be notified when someone calls you while you are already in a call. You can accept the incoming call or not. The ongoing call may be put on hold while answering the incoming call; or you may merge the calls (requires MultiSite or MultiWay support).

Deny: An incoming call will be rejected if you are already in a call. You will not be notified about the incoming call. However, the call will appear as a missed call in the call history list.

Example:

Conference 1 IncomingMultisiteCall Mode: Allow

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

FacilityService settings

FacilityService Service [1..5] Type

Up to five different facility services can be supported simultaneously. With this setting you can select what kind of services they are. A facility service is not available unless both the

FacilityService Service Name and the FacilityService Service Number settings are properly set. Only FacilityService Service 1 with Type Helpdesk is available on the Touch screen control panel. Note that the facility services are not available when using the remote control and onscreen menu.

Requires user role: ADMIN

Value space: <Other/Concierge/Helpdesk/Emergency/Security/Catering/Transportation>

Other: Select this option for services not covered by the other options.

Concierge: Select this option for concierge services.

Helpdesk: Select this option for helpdesk services.

Emergency: Select this option for emergency services.

Security: Select this option for security services.

Catering: Select this option for catering services.

Transportation: Select this option for transportation services.

Example:

FacilityService Service 1 Type: Helpdesk

FacilityService Service [1..5] Name

Enter the name of the facility service. Up to five different facility services are supported.

A facility service is not available unless both the FacilityService Service Name and the

FacilityService Service Number settings are properly set. Only FacilityService Service 1 is available on the Touch screen control panel, and the name will show on the facility service call button. The facility services are not available when using the remote control and on-screen menu.

Requires user role: ADMIN

Value space: <S: 0, 255>

Format: String with a maximum of 255 characters.

Example:

FacilityService Service 1 Name: ""

Setting passwords

Administrator Guide

Appendices

FacilityService Service [1..5] Number

Enter the number (URI or phone number) of the facility service. Up to five different facility services are supported. A facility service is not available unless both the FacilityService Service

Name and the FacilityService Service Number settings are properly set. Only FacilityService

Service 1 is available on the Touch screen control panel. The facility services are not available when using the remote control and on-screen menu.

Requires user role: ADMIN

Value space: <S: 0, 255>

Format: String with a maximum of 255 characters.

Example:

FacilityService Service 1 Number: ""

FacilityService Service [1..5] CallType

Set the call type for each facility service. Up to five different facility services are supported.

A facility service is not available unless both the FacilityService Service Name and the

FacilityService Service Number settings are properly set. Only FacilityService Service 1 is available on the Touch screen control panel. Facility services are not available when using the remote control and on-screen menu.

Requires user role: ADMIN

Value space: <Video/Audio>

Video: Select this option for video calls.

Audio: Select this option for audio calls.

Example:

FacilityService Service 1 CallType: Video

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

GPIO settings

GPIO Pin [1..4] Mode

NOTE: Applies only to Codec C60

The four GPIO pins are configured individually. The state can be retrieved by "xStatus GPIO Pin

[1..4] State". The default pin state is High (+12 V). When activated as output, they are set to 0 V.

To activate them as input, they must be pulled down to 0 V.

Requires user role: ADMIN

Value space: <InputNoAction/OutputManualState/OutputInCall/OutputMicrophonesMuted/

OutputPresentationOn/OutputAllCallsEncrypted/OutputStandbyActive/InputMuteMicrophones>

InputNoAction: The pin state can be set, but no operation is performed.

OutputManualState: The pin state can be set by "xCommand GPIO ManualState Set PinX:

<High/Low>" (to +12 V or 0 V, respectively).

OutputInCall: The pin is activated when in call, deactivated when not in call.

OutputMicrophonesMuted: The pin is activated when microphones are muted, deactivated when not muted.

OutputPresentationOn: The pin is activated when presentation is active, deactivated when presentation is not active.

OutputAllCallsEncrypted: The pin is activated when all calls are encrypted, deactivated when one or more calls are not encrypted.

OutputStandbyActive: The pin is activated when the system is in standby mode, deactivated when no longer in standby.

InputMuteMicrophones: When the pin is activated (0 V), the microphones will be muted.

When deactivated (+ 12 V), the microphones are unmuted.

Example:

GPIO Pin 1 Mode: InputNoAction

Setting passwords

Administrator Guide

Appendices

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

H323 settings

H323 NAT Mode

Gatekeeper for authentication. The authentication is a one way authentication from the codec to the H.323 Gatekeeper, i.e. the system is authenticated to the gatekeeper. If the H.323

Gatekeeper indicates that no authentication is required, the system will still try to register.

Requires the H.323 Gatekeeper Authentication Mode to be enabled.

Requires user role: ADMIN

Value space: <S: 0, 50>

Format: String with a maximum of 50 characters.

Example:

H323 Profile 1 Authentication LoginName: ""

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface Setting passwords

Administrator Guide

Appendices

H323 Profile [1..1] Authentication Password

The system sends the Authentication Login Name and the Authentication Password to a H.323

Gatekeeper for authentication. The authentication is a one way authentication from the codec to the H.323 Gatekeeper, i.e. the system is authenticated to the gatekeeper. If the H.323

Gatekeeper indicates that no authentication is required, the system will still try to register.

Requires the H.323 Gatekeeper Authentication Mode to be enabled.

Requires user role: ADMIN

Value space: <S: 0, 50>

Format: String with a maximum of 50 characters.

Example:

H323 Profile 1 Authentication Password: ""

H323 Profile [1..1] CallSetup Mode

The H.323 Call Setup Mode defines whether to use a Gatekeeper or Direct calling when establishing H323 calls.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

H323 Profile [1..1] PortAllocation

The H.323 Port Allocation setting affects the H.245 port numbers used for H.323 call signalling.

Requires user role: ADMIN

Value space: <Dynamic/Static>

Dynamic: The system will allocate which ports to use when opening a TCP connection. The reason for doing this is to avoid using the same ports for subsequent calls, as some firewalls consider this as a sign of attack. When Dynamic is selected, the H.323 ports used are from

11000 to 20999. Once 20999 is reached they restart again at 11000. For RTP and RTCP media data, the system is using UDP ports in the range 2326 to 2487. Each media channel is using two adjacent ports, ie 2330 and 2331 for RTP and RTCP respectively. The ports are automatically selected by the system within the given range. Firewall administrators should not try to deduce which ports are used when, as the allocation schema within the mentioned range may change without any further notice.

Static: When set to Static the ports are given within a static predefined range [5555-6555].

Example:

H323 Profile 1 PortAllocation: Dynamic

Setting passwords

Administrator Guide

Appendices

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

Logging settings

Logging Mode

Not applicable in this version.

Setting passwords

Administrator Guide

Appendices

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

Network settings

Network [1..1] IPStack

Select if the sFystem should use IPv4, IPv6, or dual IP stack, on the network interface. NOTE:

After changing this setting you may have to wait up to 30 seconds before it takes effect.

Requires user role: ADMIN

Value space: <Dual/IPv4/IPv6>

Dual: When set to Dual, the network interface can operate on both IP versions at the same time, and can have both an IPv4 and an IPv6 address at the same time.

IPv4: When set to IPv4, the system will use IPv4 on the network interface.

IPv6: When set to IPv6, the system will use IPv6 on the network interface.

Example:

Network 1 IPStack: Dual

Network [1..1] IPv4 Assignment

Define how the system will obtain its IPv4 address, subnet mask and gateway address. This setting only applies to systems on IPv4 networks.

Requires user role: ADMIN

Value space: <Static/DHCP>

Static: The addresses must be configured manually using the Network IPv4 Address,

Network IPv4 Gateway and Network IPv4 SubnetMask settings (static addresses).

DHCP: The system addresses are automatically assigned by the DHCP server.

Example:

Network 1 IPv4 Assignment: DHCP

Network [1..1] IPv4 Address

Enter the static IPv4 network address for the system. This setting is only applicable when

Network Assignment is set to Static.

Requires user role: ADMIN

Value space: <S: 0, 64>

Format: A valid IPv4 address.

Example:

Network 1 IPv4 Address: "192.0.2.2"

Setting passwords

Administrator Guide

Appendices

Network [1..1] IPv4 Gateway

Define the IPv4 network gateway. This setting is only applicable when the Network Assignment is set to Static.

Requires user role: ADMIN

Value space: <S: 0, 64>

Format: A valid IPv4 address.

Example:

Network 1 IPv4 Gateway: "192.0.2.1"

Network [1..1] IPv4 SubnetMask

Define the IPv4 network subnet mask. This setting is only applicable when the Network

Assignment is set to Static.

Requires user role: ADMIN

Value space: <S: 0, 64>

Format: The valid IPv4 address format.

Example:

Network 1 IPv4 SubnetMask: "255.255.255.0"

Network [1..1] IPv6 Assignment

Define how the system will obtain its IPv6 address and the default gateway address. This setting only applies to systems on IPv6 networks.

Requires user role: ADMIN

Value space: <Static/DHCPv6/Autoconf>

Static: The codec and gateway IP addresses must be configured manually using the Network

IPv6 Address and Network IPv6 Gateway settings. The options, for example NTP and DNS server addresses, must either be set manually or obtained from a DHCPv6 server. The

Network IPv6 DHCPOptions setting determines which method to use.

DHCPv6: All IPv6 addresses, including options, will be obtained from a DHCPv6 server. See

RFC 3315 for a detailed description. The Network IPv6 DHCPOptions setting will be ignored.

Autoconf: Enable IPv6 stateless autoconfiguration of the IPv6 network interface. See RFC

4862 for a detailed description. The options, for example NTP and DNS server addresses, must either be set manually or obtained from a DHCPv6 server. The Network IPv6

DHCPOptions setting determines which method to use.

Example:

Network 1 IPv6 Assignment: Autoconf

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

Administrator Guide

Appendices Setting passwords

Network [1..1] DHCP RequestTFTPServerAddress

This setting is used only for video systems that are registered to a Cisco Unified

Communications Manager (CUCM).

The setting determines whether the endpoint should ask the DHCP server for DHCP option 150, so that it can discover the address of the TFTP server (provisioning server) automatically.

If this setting is Off or the DHCP server does not support option 150, the TFTP server address must be set manually using the Provisioning ExternalManager Address setting.

If the Network VLAN Voice Mode setting is Auto and the Cisco Discovery Protocol (CDP) assigns an ID to the voice VLAN, then a request for option 150 will always be sent. That is, the

Network DHCP RequestTFTFServerAddress setting will be ignored.

Requires user role: ADMIN

Value space: <Off/On>

Off: The video system will not send a request for DHCP option 150 and the address of the

TFTP server must be set manually. See the note above for any exception to this rule.

On: The video system will send a request for option 150 to the DHCP server so that it can automatically discover the address of the TFTP server.

Example:

Network 1 DHCP RequestTFTPServerAddress: On

Network [1..1] DNS Domain Name

DNS Domain Name is the default domain name suffix which is added to unqualified names.

Example: If the DNS Domain Name is "company.com" and the name to lookup is

"MyVideoSystem", this will result in the DNS lookup "MyVideoSystem.company.com".

Requires user role: ADMIN

Value space: <S: 0, 64>

Format: String with a maximum of 64 characters.

Example:

Network 1 DNS Domain Name: ""

Network [1..1] DNS Server [1..3] Address

Define the network addresses for DNS servers. Up to 3 addresses may be specified. If the network addresses are unknown, contact your administrator or Internet Service Provider.

Requires user role: ADMIN

Value space: <S: 0, 64>

Format: A valid IPv4 address or IPv6 address.

Example:

Network 1 DNS Server 1 Address: ""

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface Setting passwords

Administrator Guide

Appendices

Network [1..1] QoS Mode

The QoS (Quality of Service) is a method which handles the priority of audio, video and data in the network. The QoS settings must be supported by the infrastructure. Diffserv (Differentiated

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface Setting passwords

Administrator Guide

Appendices

Network [1..1] IEEE8021X Mode

The system can be connected to an IEEE 802.1X LAN network, with a port-based network access control that is used to provide authenticated network access for Ethernet networks.

Requires user role: ADMIN

Value space: <Off/On>

Off: The 802.1X authentication is disabled (default).

On: The 802.1X authentication is enabled.

Example:

Network 1 IEEE8021X Mode: Off

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface Setting passwords

Administrator Guide

Appendices

Network [1..1] IEEE8021X TlsVerify

Verification of the server-side certificate of an IEEE802.1x connection against the certificates in the local CA-list when TLS is used. The CA-list must be uploaded to the video system. This can be done from the web interface.

This setting takes effect only when Network [1..1] IEEE8021X Eap Tls is enabled (On).

Requires user role: ADMIN

Value space: <Off/On>

Off: When set to Off, TLS connections are allowed without verifying the server-side X.509 certificate against the local CA-list. This should typically be selected if no CA-list has been uploaded to the codec.

On: When set to On, the server-side X.509 certificate will be validated against the local CAlist for all TLS connections. Only servers with a valid certificate will be allowed.

Example:

Network 1 IEEE8021X TlsVerify: Off

Network [1..1] IEEE8021X UseClientCertificate

Authentication using a private key/certificate pair during an IEEE802.1x connection. The authentication X.509 certificate must be uploaded to the video system. This can be done from the web interface.

The 802.1X Anonymous ID string is to be used as unencrypted identity with EAP (Extensible

Authentication Protocol) types that support different tunneled identity, like EAP-PEAP and EAP-

TTLS. If set, the anonymous ID will be used for the initial (unencrypted) EAP Identity Request.

Requires user role: ADMIN

Value space: <S: 0, 64>

Format: String with a maximum of 64 characters.

Example:

Network 1 IEEE8021X AnonymousIdentity: ""

Network [1..1] IEEE8021X Eap Md5

Set the Md5 (Message-Digest Algorithm 5) mode. This is a Challenge Handshake

Authentication Protocol that relies on a shared secret. Md5 is a Weak security.

Requires user role: ADMIN

Value space: <Off/On>

Off: The EAP-MD5 protocol is disabled.

On: The EAP-MD5 protocol is enabled (default).

Example:

Network 1 IEEE8021X Eap Md5: On

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

Network [1..1] IEEE8021X Eap Ttls

Set the TTLS (Tunneled Transport Layer Security) mode. Authenticates LAN clients without the need for client certificates. Developed by Funk Software and Certicom. Usually supported by

Agere Systems, Proxim and Avaya.

Requires user role: ADMIN

Value space: <Off/On>

Off: The EAP-TTLS protocol is disabled.

On: The EAP-TTLS protocol is enabled (default).

Example:

Network 1 IEEE8021X Eap Ttls: On

Network [1..1] IEEE8021X Eap Tls

Enable or disable the use of EAP-TLS (Transport Layer Security) for IEEE802.1x connections.

The EAP-TLS protocol, defined in RFC 5216, is considered one of the most secure EAP standards. LAN clients are authenticated using client certificates.

Requires user role: ADMIN

Value space: <Off/On>

Off: The EAP-TLS protocol is disabled.

On: The EAP-TLS protocol is enabled (default).

Example:

Network 1 IEEE8021X Eap Tls: On

Network [1..1] IEEE8021X Eap Peap

Set the Peap (Protected Extensible Authentication Protocol) mode. Authenticates LAN clients without the need for client certificates. Developed by Microsoft, Cisco and RSA Security.

Requires user role: ADMIN

Value space: <Off/On>

Off: The EAP-PEAP protocol is disabled.

On: The EAP-PEAP protocol is enabled (default).

Example:

Network 1 IEEE8021X Eap Peap: On

Administrator Guide

Appendices Setting passwords

Network [1..1] MTU

Set the Ethernet MTU (Maximum Transmission Unit).

Requires user role: ADMIN

Value space: <576..1500>

Range: Select a value from 576 to 1500 bytes.

Example:

Network 1 MTU: 1500

Network [1..1] Speed

Set the Ethernet link speed.

Requires user role: ADMIN

Value space: <Auto/10half/10full/100half/100full/1000full>

Auto: Autonegotiate link speed.

10half: Force link to 10 Mbps half-duplex.

10full: Force link to 10 Mbps full-duplex.

100half: Force link to 100 Mbps half-duplex.

100full: Force link to 100 Mbps full-duplex.

1000full: Force link to 1 Gbps full-duplex.

Example:

Network 1 Speed: Auto

Network [1..1] TrafficControl Mode

Set the network traffic control mode to decide how to control the video packets transmission speed.

Requires user role: ADMIN

Value space: <Off/On>

Off: Transmit video packets at link speed.

On: Transmit video packets at maximum 20 Mbps. Can be used to smooth out bursts in the outgoing network traffic.

Example:

Network 1 TrafficControl: On

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

Network [1..1] RemoteAccess Allow

Filter IP addresses for access to ssh/telnet/HTTP/HTTPS.

Requires user role: ADMIN

Value space: <S: 0, 255>

Format: String with a maximum of 255 characters, comma separated IP adresses or IP range.

Example:

Network 1 RemoteAccess Allow: "192.168.1.231, 192.168.1.182"

Network [1..1] VLAN Voice Mode

Set the VLAN voice mode. The VLAN Voice Mode will be set to Auto automatically if you choose Cisco UCM (Cisco Unified Communications Manager) as provisioning infrastructure via the Provisioning Wizard on the Touch screen control panel.

Requires user role: ADMIN

Value space: <Auto/Manual/Off>

Auto: The Cisco Discovery Protocol (CDP), if available, assigns an id to the voice VLAN. If

CDP is not available, VLAN is not enabled.

Manual: The VLAN ID is set manually using the Network VLAN Voice VlanId setting. If CDP is available, the manually set value will be overruled by the value assigned by CDP.

Off: VLAN is not enabled.

Example:

Network 1 VLAN Voice Mode: Off

Network [1..1] VLAN Voice VlanId

Set the VLAN voice ID. This setting will only take effect if VLAN Voice Mode is set to Manual.

Requires user role: ADMIN

Value space: <1..4094>

Range: Select a value from 1 to 4094.

Example:

Network 1 VLAN Voice VlanId: 1

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Setting passwords

Administrator Guide

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

NetworkPort settings

NetworkPort [2] Mode

Define if the network port 2 shall be enabled for direct pairing with a Cisco TelePresence Touch screen control panel.

NOTE: Restart the system for any change to this setting to take effect.

Requires user role: ADMIN

Value space: <Inactive/DirectPairing>

Inactive: Set the NetworkPort 2 to Inactive when no device is connected.

DirectPairing: Set the NetworkPort 2 to DirectPairing when you have a Cisco TelePresence

Touch screen control panel connected to the port. This will enable for direct pairing between the Touch screen control panel and the codec.

Example:

NetworkPort 2 Mode: Inactive

Setting passwords

Administrator Guide

Appendices

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

NetworkServices settings

NetworkServices H323 Mode

Determine whether the system should be able to place and receive H.323 calls or not.

Requires user role: ADMIN

Value space: <Off/On>

Off: Disable the possibility to place and receive H.323 calls.

On: Enable the possibility to place and receive H.323 calls (default).

Example:

NetworkServices H323 Mode: On

NetworkServices HTTP Mode

Set the HTTP mode to enable/disable access to the system through a web browser. The web interface is used for system management, call management such as call transfer, diagnostics and software uploads.

Requires user role: ADMIN

Value space: <Off/On>

Off: The HTTP protocol is disabled.

On: The HTTP protocol is enabled.

Example:

NetworkServices HTTP Mode: On

NetworkServices SIP Mode

Determine whether the system should be able to place and receive SIP calls or not.

Requires user role: ADMIN

Value space: <Off/On>

Off: Disable the possibility to place and receive SIP calls.

On: Enable the possibility to place and receive SIP calls (default).

Example:

NetworkServices SIP Mode: On

Setting passwords

Administrator Guide

Appendices

NetworkServices Telnet Mode

Administrator Guide

Appendices

NetworkServices MultiWay Address

The MultiWay address must be equal to the Conference Factory Alias, as configured on the

Video Communication Server. The Multiway™ conferencing enables video endpoint users to introduce a 3rd party into an existing call.

Multiway™ can be used in the following situations:

1) When you want to add someone else in to your existing call.

2) When you are called by a 3rd party while already in a call and you want to include that person in the call.

Requirements: The Codec C60/C40 must run software version TC4.0 (or later), Video

Communication Server (VCS) version X5 (or later) and Codian MCU version 3.1 (or later). Video systems invited to join the Multiway™ conference must support the H.323 routeToMC facility message if in an H.323 call, or SIP REFER message if in a SIP call.

Requires user role: ADMIN

Value space: <S: 0, 255>

Format: String with a maximum of 255 characters (a valid dial URI).

Example:

NetworkServices MultiWay Address: "h323:[email protected]"

NetworkServices MultiWay Protocol

Determine the protocol to be used for MultiWay calls.

NetworkServices HTTPS VerifyClientCertificate

When the video system connects to a HTTPS client (like a web browser), the client can be asked to present a certificate to the video system to identify itself.

Requires user role: ADMIN

Value space: <Off/On>

Off: Do not verify client certificates.

On: Requires the client to present a certificate that is signed by a trusted Certificate

Authority (CA). This requires that a list of trusted CAs are uploaded to the system in advance.

Example:

NetworkServices HTTPS VerifyClientCertificate: Off

NetworkServices HTTPS OCSP Mode

Define the support for OCSP (Online Certificate Status Protocol) responder services. The OCSP feature allows users to enable OCSP instead of certificate revocation lists (CRLs) to check the certificate status.

For any outgoing HTTPS connection, the OCSP responder is queried of the status. If the corresponding certificate has been revoked, then the HTTPS connection will not be used.

Requires user role: ADMIN

Value space: <Off/On>

Off: Disable OCSP support.

On: Enable OCSP support.

Example:

NetworkServices HTTPS OCSP Mode: Off

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

NetworkServices HTTPS OCSP URL

Specify the URL of the OCSP responder (server) that will be used to check the certificate status.

Requires user role: ADMIN

Value space: <S: 0, 255>

Format: String with a maximum of 255 characters.

Example:

NetworkServices HTTPS OCSP URL: "http://ocspserver.company.com:81"

NetworkServices NTP Mode

The Network Time Protocol (NTP) is used to synchronize the time of the system to a reference time server. The time server will subsequently be queried every 24th hour for time updates.

The time will be displayed on the top of the screen. The system will use the time to timestamp messages transmitted to Gatekeepers or Border Controllers requiring H.235 authentication.

The system will use the time to timestamp messages transmitted to Gatekeepers or Border

Controllers that requires H.235 authentication. It is also used for timestamping Placed Calls,

Missed Calls and Received Calls.

Requires user role: ADMIN

Value space: <Auto/Off/Manual>

Auto: The system will use the NTP server, by which address is supplied from the DHCP server in the network. If no DHCP server is used, or the DHCP server does not provide the system with a NTP server address, the system will use the static defined NTP server address specified by the user.

Off: The system will not use an NTP server.

Manual: The system will always use the static defined NTP server address specified by the user.

Example:

NetworkServices NTP Mode: Manual

NetworkServices NTP Address

Enter the NTP Address to define the network time protocol server address. This address will be used if NTP Mode is set to Manual, or if set to Auto and no address is supplied by a DHCP server.

Requires user role: ADMIN

Value space: <S: 0, 64>

Format: A valid IPv4 address, IPv6 address or DNS name.

Example:

NetworkServices NTP Address: "1.ntp.tandberg.com"

Administrator Guide

Appendices Setting passwords

NetworkServices SNMP Mode

SNMP (Simple Network Management Protocol) is used in network management systems to monitor network-attached devices (routers, servers, switches, projectors, etc) for conditions that warrant administrative attention. SNMP exposes management data in the form of variables on the managed systems, which describe the system configuration. These variables can then be queried (set to ReadOnly) and sometimes set (set to ReadWrite) by managing applications.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

NetworkServices SSH Mode: On

NetworkServices SSH AllowPublicKey

Secure Shell (SSH) public key authentication can be used to access the codec.

Requires user role: ADMIN

Value space: <Off/On>

Off: The SSH public key is not allowed.

On: The SSH public key is allowed.

Example:

NetworkServices SSH AllowPublicKey: On

Administrator Guide

Appendices Setting passwords

NetworkServices CTMS Mode

This setting determines whether or not to allow multiparty conferences controlled by a Cisco

TelePresence Multipoint Switch (CTMS).

Video systems running software TC5.0 or later are able to initiate or join non-encrypted multiparty conferences controlled by CTMS version 1.8 or later. Encrypted conferences are supported as from software versions TC6.0 and CTMS 1.9.1. Encryption is addressed in the

NetworkServices CTMS Encryption setting.

Requires user role: ADMIN

Value space: <Off/On>

Off: Multiparty conferencing via CTMS is prohibited.

On: Multiparty conferencing via CTMS is allowed.

Example:

NetworkServices CTMS Mode: On

NetworkServices CTMS Encryption

This setting indicates whether or not the video system supports encryption when participating in a multiparty meeting controlled by a Cisco TelePresence Multipoint Switch (CTMS).

CTMS allows three security settings for meetings: non-secure (not encrypted), best effort

(encrypted if all participants support encryption, otherwise not encrypted) and secure (always encrypted).

Requires user role: ADMIN

Value space: <Off/BestEffort>

Off: The video system does not allow encryption and therefore cannot participate in a secure

CTMS meeting (encrypted). When participating in a best effort CTMS meeting, the meeting will be downgraded to non-secure (not encrypted).

BestEffort: The video system can negotiate encryption parameters with CTMS and participate in a secure CTMS meeting (encrypted). Do not use this value if the CTMS version is older than 1.9.1.

Example:

NetworkServices CTMS Encryption: Off

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

Phonebook settings

Phonebook Server [1..1] ID

Enter a name for the external phone book.

Requires user role: ADMIN

Value space: <S: 0, 64>

Format: String with a maximum of 64 characters.

Example:

Phonebook Server 1 ID: ""

Phonebook Server [1..1] Type

Select the phonebook server type.

Requires user role: ADMIN

Value space: <VCS/TMS/Callway/CUCM>

VCS: Select VCS if the phonebook is located on the Cisco TelePresence Video

Communication Server.

TMS: Select TMS if the phonebook is located on the Cisco TelePresence Management Suite server.

Callway: Select Callway if the phonebook is to be provided by the WebEx TelePresence subscription service (formerly called CallWay). Contact your WebEx TelePresence provider for more information.

CUCM: Select CUCM if the phonebook is located on the Cisco Unified Communications

Manager.

Example:

Phonebook Server 1 Type: TMS

Phonebook Server [1..1] URL

Enter the address (URL) to the external phone book server.

Requires user role: ADMIN

Value space: <S: 0, 255>

Format: String with a maximum of 255 characters.

Example:

Phonebook Server 1 URL: "http://tms.company.com/tms/public/external/ phonebook/phonebookservice.asmx"

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Setting passwords

Administrator Guide

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface Setting passwords

Administrator Guide

Appendices

Provisioning settings

Provisioning Connectivity

This setting controls how the device discovers whether it should request an internal or external configuration from the provisioning server.

Requires user role: ADMIN

Value space: <Internal/External/Auto>

Internal: Request internal configuration.

External: Request external configuration.

Auto: Automatically discover using NAPTR queries whether internal or external configurations should be requested. If the NAPTR responses have the "e" flag, external configurations will be requested. Otherwise internal configurations will be requested.

Example:

Provisioning Connectivity: Auto

Provisioning Mode

It is possible to configure a video system using a provisioning system (external manager).

This allows video conferencing network administrators to manage many video systems simultaneously. With this setting you choose which type of provisioning system to use.

Provisioning can also be switched off. Contact your provisioning system provider/representative for more information.

Requires user role: ADMIN

Value space: <Off/TMS/VCS/CallWay/CUCM/Auto/Edge>

Off: The video system will not be configured by a provisioning system.

TMS: The video system will be configured using TMS (Cisco TelePresence Management

System).

VCS: The video system will be configured using VCS (Cisco TelePresence Video

Communication Server).

Contents Introduction Web interface Setting passwords

Administrator Guide

Appendices

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

RTP settings

RTP Ports Range Start

Specify the first port in the range of RTP ports. Also see the H323 Profile [1..1] PortAllocation setting.

NOTE: Restart the system for any change to this setting to take effect.

Requires user role: ADMIN

Value space: <1024..65502>

Range: Select a value from 1024 to 65502.

Example:

RTP Ports Range Start: 2326

RTP Ports Range Stop

Specify the last RTP port in the range. Also see the H323 Profile [1..1] PortAllocation setting.

NOTE: Restart the system for any change to this setting to take effect.

Requires user role: ADMIN

Value space: <1056..65535>

Range: Select a value from 1056 to 65535.

Example:

RTP Ports Range Stop: 2486

Setting passwords

Administrator Guide

Appendices

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface Setting passwords

Administrator Guide

Appendices

Security settings

Security Audit Logging Mode

Determine where to record or transmit the audit logs. The audit logs are sent to a syslog server.

When using the External/ExternalSecure modes and setting the port assignment to manual in the Security Audit Server PortAssignment setting, you must also enter the address and port number for the audit server in the Security Audit Server Address and Security Audit Server Port settings.

Requires user role: AUDIT

Value space: <Off/Internal/External/ExternalSecure>

Off: No audit logging is performed.

Internal: The system records the audit logs to internal logs, and rotates logs when they are full.

External: The system sends the audit logs to an external syslog server. The syslog server must support UDP.

ExternalSecure: The system sends encrypted audit logs to an external syslog server that is verified by a certificate in the Audit CA list. The Audit CA list file must be uploaded to the codec using the web interface. The common_name parameter of a certificate in the CA list must match the IP address of the syslog server, and the secure TCP server must be set up to listen for secure (TLS) TCP Syslog messages.

Example:

Security Audit Logging Mode: Off

Security Audit OnError Action

Determine what happens when the connection to the syslog server is lost. This setting is only relevant when Security Audit Logging Mode is set to ExternalSecure.

Requires user role: AUDIT

Value space: <Halt/Ignore>

Halt: If a halt condition is detected the system codec is rebooted and only the auditor is allowed to operate the unit until the halt condition has passed. When the halt condition has passed the audit logs are re-spooled to the syslog server. Halt conditions are: A network breach (no physical link), no syslog server running (or incorrect address or port to the syslog server), TLS authentication failed (if in use), local backup (re-spooling) log full.

Ignore: The system will continue its normal operation, and rotate internal logs when full.

When the connection is restored it will again send its audit logs to the syslog server.

Example:

ExternalSecure.

Manual: Will use the port value defined in the Security Audit Server Port setting.

Example:

Security Audit Server PortAssignment: Auto

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

Security Session ShowLastLogon

When logging in to the system using SSH or Telnet you will see the UserId, time and date of the last session that did a successful login.

Requires user role: ADMIN

Value space: <Off/On>

On: Show information about the last session.

Off: Do not show information about the last session.

Example:

Security Session ShowLastLogon: Off

Security Session InactivityTimeout

Determine how long the system will accept inactivity from the user before he is automatically logged out.

Requires user role: ADMIN

Value space: <0..10000>

Range: Select a value between 1 and 10000 seconds; or select 0 when inactivity should not enforce automatic logout.

Example:

Security Session InactivityTimeout: 0

Setting passwords

Administrator Guide

Appendices

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

SerialPort settings

SerialPort Mode

Enable/disable the serial port (COM port).

Requires user role: ADMIN

Value space: <Off/On>

Off: Disable the serial port.

On: Enable the serial port.

Example:

SerialPort Mode: On

SerialPort BaudRate

Specify the baud rate (data transmission rate, bits per second) for the serial port. The default value is 38400.

Other connection parameters for the serial port are: Data bits: 8; Parity: None; Stop bits: 1; Flow control: None.

Requires user role: ADMIN

Value space: <9600/19200/38400/57600/115200>

Range: Select a baud rate from the baud rates listed (bps).

Example:

SerialPort BaudRate: 38400

SerialPort LoginRequired

Determine if login shall be required when connecting to the serial port.

Requires user role: ADMIN

Value space: <Off/On>

Off: The user can access the codec via the serial port without any login.

On: Login is required when connecting to the codec via the serial port.

Example:

SerialPort LoginRequired: On

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Setting passwords

Administrator Guide

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

SIP settings

SIP ANAT

ANAT (Alternative Network Address Types) enables media negotiation for multiple addresses and address types, as specified in RFC 4091.

Requires user role: ADMIN

Value space: <Off/On>

Off: Disable ANAT.

On: Enable ANAT.

Example:

SIP ANAT: Off

SIP AuthenticateTransferror

Not applicable in this version.

SIP ListenPort

Turn on or off the listening for incoming connections on the SIP TCP/UDP ports. If turned off, the endpoint will only be reachable through the SIP registrar (CUCM or VCS). It is recommended to leave this setting at its default value.

Requires user role: ADMIN

Value space: <On/Off>

On: Listening for incoming connections on the SIP TCP/UDP ports is turned on.

Off: Listening for incoming connections on the SIP TCP/UDP ports is turned off.

Example:

SIP ListenPort: On

Setting passwords

Administrator Guide

Appendices

SIP PreferredIPMedia

Define the preferred IP version for sending and receiving media (audio, video, data). Only applicable when both Network IPStack and Conference CallProtocolIPStack are set to Dual, and the network does not have a mechanism for choosing the preferred IP version.

Requires user role: ADMIN

Value space: <IPv4/IPv6>

IPv4: The preferred IP version for media is IPv4.

IPv6: The preferred IP version for media is IPv6.

Example:

SIP PreferredIPMedia: IPv4

SIP PreferredIPSignaling

Define the preferred IP version for signaling (audio, video, data). Only applicable when both

Network IPStack and Conference CallProtocolIPStack are set to Dual, and the network does not have a mechanism for choosing the preferred IP version. It also determines the priority of the A/AAAA lookups in DNS, so that the preferred IP version is used for registration.

Requires user role: ADMIN

Value space: <IPv4/IPv6>

IPv4: The preferred IP version for signaling is IPv4.

IPv6: The preferred IP version for signaling is IPv6.

Example:

SIP PreferredIPSignaling: IPv4

SIP OCSP Mode

Not applicable in this version.

SIP OCSP DefaultResponder

Not applicable in this version.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface Setting passwords

Administrator Guide

Appendices

SIP Profile [1..1] Ice Mode

ICE (Interactive Connectivity Establishment, RFC 5245) is a NAT traversal solution that the endpoints can use to discover the optimized media path. Thus the shortest route for audio and video is always secured between the endpoints. NOTE: ICE is not supported when registered to

CUCM (Cisco Unified Communication Manager).

SIP Profile [1..1] Turn DropRflx

DropRflx will make the endpoint force media through the Turn relay, unless the remote endpoint is on the same network.

Requires user role: ADMIN

Value space: <Off/On>

Off: Disable DropRflx.

On: The system will force media through the Turn relay when the remote endpoint is on another network.

Example:

SIP Profile Turn DropRflx: Off

SIP Profile [1..1] Turn Server

This is the address of the TURN (Traversal Using Relay NAT) server that the endpoints will use.

It is used as a media relay fallback and it is also used to discover the endpoint’s own public IP address.

Requires user role: ADMIN

Value space: <S: 0, 255>

Format: The preferred format is DNS SRV record (e.g. _turn._udp.<domain>), or it can be a valid IPv4 or IPv6 address.

Example:

SIP Profile 1 Turn Server: " _ turn. _ udp.example.com"

SIP Profile [1..1] Turn UserName

The user name needed for accessing the TURN server.

Requires user role: ADMIN

Value space: <S: 0, 128>

Format: String with a maximum of 128 characters.

Example:

SIP Profile 1 Turn UserName: ""

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

Administrator Guide

Appendices Setting passwords

SIP Profile [1..1] Authentication [1..1] Password

This is the password part of the credentials used to authenticate towards the SIP proxy.

Requires user role: ADMIN

Value space: <S: 0, 128>

Format: String with a maximum of 128 characters.

Example:

SIP Profile 1 Authentication 1 Password: ""

SIP Profile [1..1] DefaultTransport

Select the transport protocol to be used over the LAN.

Requires user role: ADMIN

Value space: <TCP/UDP/Tls/Auto>

TCP: The system will always use TCP as the default transport method.

UDP: The system will always use UDP as the default transport method.

Tls: The system will always use TLS as the default transport method. For TLS connections a SIP CA-list can be uploaded to the video system. If no such CA-list is available on the system then anonymous Diffie Hellman will be used.

Auto: The system will try to connect using transport protocols in the following order: TLS,

TCP, UDP.

Example:

SIP Profile 1 DefaultTransport: Auto

SIP Profile [1..1] TlsVerify

For TLS connections a SIP CA-list can be uploaded to the video system. This can be done from the web interface.

Requires user role: ADMIN

Value space: <Off/On>

Off: Set to Off to allow TLS connections without verifying them. The TLS connections are allowed to be set up without verifying the x.509 certificate received from the server against the local CA-list. This should typically be selected if no SIP CA-list has been uploaded.

On: Set to On to verify TLS connections. Only TLS connections to servers, whose x.509 certificate is validated against the CA-list, will be allowed.

Example:

SIP Profile 1 TlsVerify: Off

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface Setting passwords

Administrator Guide

Appendices

SIP Profile [1..1] Outbound

Turn on or off the client initiated connections mechanism for firewall traversal, connection reuse and redundancy. The current version supports RFC 5626.

Requires user role: ADMIN

Value space: <Off/On>

Off: Connect to the single proxy configured first in Proxy Address list.

On: Set up multiple outbound connections to servers in the Proxy Address list.

Example:

SIP Profile 1 Outbound: Off

Value space: <S: 0, 255>>

Format: String with a maximum of 255 characters.

Example:

SIP Profile 1 Mailbox: "12345678"

SIP Profile [1..1] Line

When registered to a Cisco Unified Communications Manager (CUCM) the endpoint may be part of a shared line. This means that several devices share the same directory number. The different devices sharing the same number receive status from the other appearances on the line as defined in RFC 4235.

Note that shared lines are set up by CUCM, not by the endpoint. Therefore do not change this setting manually; CUCM pushes this information to the endpoint when required.

Requires user role: ADMIN

Value space: <Private/Shared>

Shared: The system is part of a shared line and is therefore sharing its directory number with other devices.

Private: This system is not part of a shared line (default).

Example:

SIP Profile 1 Line: Private

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface Setting passwords

Administrator Guide

Appendices

Standby settings

Standby Control

Determine whether the system should go into standby mode or not.

Requires user role: ADMIN

Value space: <Off/On>

Off: The system will not enter standby mode.

On: Enter standby mode when the Standby Delay has timed out. Requires the Standby Delay to be set to an appropriate value.

Example:

Standby Control: On

Standby Delay

Define how long (in minutes) the system shall be in idle mode before it goes into standby mode.

Requires the Standby Control to be enabled.

Requires user role: ADMIN

Value space: <1..480>

Range: Select a value from 1 to 480 minutes.

Example:

Standby Delay: 10

Standby BootAction

Define the camera position after a restart of the codec.

Requires user role: ADMIN

Value space: <None/Preset1/Preset2/Preset3/Preset4/Preset5/Preset6/Preset7/Preset8/

Preset9/Preset10/Preset11/Preset12/Preset13/Preset14/Preset15/RestoreCameraPosition/

DefaultCameraPosition>

None: No action.

Preset1 to Preset15: After a reboot the camera position will be set to the position defined by the selected preset.

RestoreCameraPosition: After a reboot the camera position will be set to the position it had before the last boot.

DefaultCameraPosition: After a reboot the camera position will be set to the factory default position.

Example:

Standby BootAction: DefaultCameraPosition

Standby StandbyAction

Define the camera position when going into standby mode.

Requires user role: ADMIN

Value space: <None/PrivacyPosition>

None: No action.

PrivacyPosition: Turns the camera to a sideways position for privacy.

Example:

Standby StandbyAction: PrivacyPosition

Standby WakeupAction

Define the camera position when leaving standby mode.

Requires user role: ADMIN

Value space: <None/Preset1/Preset2/Preset3/Preset4/Preset5/Preset6/Preset7/Preset8/

Preset9/Preset10/Preset11/Preset12/Preset13/Preset14/Preset15/RestoreCameraPosition/

DefaultCameraPosition>

None: No action.

Preset1 to Preset15: When leaving standby the camera position will be set to the position defined by the selected preset.

Set the call logging mode for calls that are received or placed by the system. The call logs may then be viewed via the web interface or using the xHistory command.

Requires user role: ADMIN

Value space: <Off/On>

Off: Disable logging.

On: Enable logging.

Example:

SystemUnit CallLogging Mode: On

Setting passwords

Administrator Guide

Appendices

SystemUnit ContactInfo Type

Choose which type of contact information to show in the status field in the upper left corner of the main display and Touch screen control panel. The information can also be read with the command xStatus SystemUnit ContactInfo.

Requires user role: ADMIN

Value space: <Auto/None/IPv4/IPv6/H323Id/E164Alias/H320Number/SipUri/SystemName/

DisplayName>

Auto: Show the address which another system can dial to reach this system. The address depends on the default call protocol and system registration.

None: Do not show any contact information in the status field.

IPv4: Show the IPv4 address as contact information.

IPv6: Show the IPv6 address as contact information.

H323Id: Show the H.323 ID as contact information (see the H323 Profile [1..1] H323Alias ID setting).

E164Alias: Show the H.323 E164 Alias as contact information (see the H323 Profile [1..1]

H323Alias E164 setting).

H320Number: Show the H.320 number as contact information (only applicable if connected to a Cisco TelePresence ISDN Link gateway).

SipUri: Show the SIP URI as contact information (see the SIP Profile [1..1] URI setting).

SystemName: Show the system name as contact information (see the SystemUnit Name setting).

DisplayName: Show the display name as contact information (see the SIP Profile [1..1]

DisplayName setting).

Example:

SystemUnit ContactInfo Type: Auto

104

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

SystemUnit IrSensor

Both the Codec C Series and PrecisionHD camera have IR sensors, and only one of them needs to be enabled at the time. The IR sensor LED is located on the front of the codec and the camera and flickers when an IR signal is received from the remote control.

Requires user role: ADMIN

Value space: <Auto/Off/On>

Auto: The system will automatically disable the IR sensor on the codec if the IR sensor at camera is enabled. Otherwise, the IR sensor on the codec will be enabled.

Off: Disable the IR sensor on the codec.

On: Enable the IR sensor on the codec.

Example:

SystemUnit IrSensor: Auto

Setting passwords

Administrator Guide

Appendices

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

Time settings

Time Zone

Set the time zone where the system is located, using Windows time zone description format.

Requires user role: USER

Value space: <GMT-12:00 (International Date Line West)/GMT-11:00 (Midway Island, Samoa)/

GMT-10:00 (Hawaii)/GMT-09:00 (Alaska)/GMT-08:00 (Pacific Time (US & Canada); Tijuana)/

GMT-07:00 (Arizona)/GMT-07:00 (Mountain Time (US & Canada))/GMT-07:00 (Chihuahua,

La Paz, Mazatlan)/GMT-06:00 (Central America)/GMT-06:00 (Saskatchewan)/GMT-06:00

(Guadalajara, Mexico City, Monterrey)/GMT-06:00 (Central Time (US & Canada))/GMT-05:00

(Indiana (East))/GMT-05:00 (Bogota, Lima, Quito)/GMT-05:00 (Eastern Time (US & Canada))/

GMT-04:30 (Caracas)/GMT-04:00 (La Paz)/GMT-04:00 (Santiago)/GMT-04:00 (Atlantic Time

(Canada))/GMT-03:30 (Newfoundland)/GMT-03:00 (Buenos Aires, Georgetown)/GMT-03:00

(Greenland)/GMT-03:00 (Brasilia)/GMT-02:00 (Mid-Atlantic)/GMT-01:00 (Cape Verde Is.)/

GMT-01:00 (Azores)/GMT (Casablanca, Monrovia)/GMT (Coordinated Universal Time)/GMT

(Greenwich Mean Time : Dublin, Edinburgh, Lisbon, London)/GMT+01:00 (West Central Africa)/

GMT+01:00 (Amsterdam, Berlin, Bern, Rome, Stockholm, Vienna)/GMT+01:00 (Brussels,

Copenhagen, Madrid, Paris)/GMT+01:00 (Sarajevo, Skopje, Warsaw, Zagreb)/GMT+01:00

(Belgrade, Bratislava, Budapest, Ljubljana, Prague)/GMT+02:00 (Harare, Pretoria)/GMT+02:00

(Jerusalem)/GMT+02:00 (Athens, Istanbul, Minsk)/GMT+02:00 (Helsinki, Kyiv, Riga, Sofia,

Tallinn, Vilnius)/GMT+02:00 (Cairo)/GMT+02:00 (Bucharest)/GMT+03:00 (Nairobi)/GMT+03:00

(Kuwait, Riyadh)/GMT+04:00 (Moscow, St. Petersburg, Volgograd)/GMT+03:00 (Baghdad)/

GMT+03:30 (Tehran)/GMT+04:00 (Abu Dhabi, Muscat)/GMT+04:00 (Baku, Tbilisi, Yerevan)/

GMT+04:30 (Kabul)/GMT+05:00 (Islamabad, Karachi, Tashkent)/GMT+05:00 (Ekaterinburg)/

GMT+05:30 (Chennai, Kolkata, Mumbai, New Delhi)/GMT+05:45 (Kathmandu)/GMT+06:00 (Sri

Jayawardenepura)/GMT+06:00 (Astana, Dhaka)/GMT+06:00 (Almaty, Novosibirsk)/GMT+06:30

(Rangoon)/GMT+07:00 (Bangkok, Hanoi, Jakarta)/GMT+07:00 (Krasnoyarsk)/GMT+08:00 (Perth)/

GMT+08:00 (Taipei)/GMT+08:00 (Kuala Lumpur, Singapore)/GMT+08:00 (Beijing, Chongqing,

Hong Kong, Urumqi)/GMT+08:00 (Irkutsk, Ulaan Bataar)/GMT+09:00 (Osaka, Sapporo, Tokyo)/

GMT+09:00 (Seoul)/GMT+09:00 (Yakutsk)/GMT+09:30 (Darwin)/GMT+09:30 (Adelaide)/

GMT+10:00 (Guam, Port Moresby)/GMT+10:00 (Brisbane)/GMT+10:00 (Vladivostok)/GMT+10:00

(Hobart)/GMT+10:00 (Canberra, Melbourne, Sydney)/GMT+11:00 (Magadan, Solomon Is.,

New Caledonia)/GMT+12:00 (Fiji, Kamchatka, Marshall Is.)/GMT+12:00 (Auckland, Wellington)/

GMT+13:00 (Nuku alofa)>

Range: Select a time zone from the list time zones. If using a command line interface; watch up for typos.

Example:

Time Zone: "GMT (Greenwich Mean Time : Dublin, Edinburgh, Lisbon,

London)"

Setting passwords

Time TimeFormat

Set the time format.

Requires user role: USER

Value space: <24H/12H>

24H: Set the time format to 24 hours.

12H: Set the time format to 12 hours (AM/PM).

Example:

Time TimeFormat: 24H

Time DateFormat

Set the date format.

Requires user role: USER

Value space: <DD_MM_YY/MM_DD_YY/YY_MM_DD>

DD_MM_YY: The date January 30th 2010 will be displayed: 30.01.10

MM_DD_YY: The date January 30th 2010 will be displayed: 01.30.10

YY_MM_DD: The date January 30th 2010 will be displayed: 10.01.30

Example:

Time DateFormat: DD _ MM _ YY

Administrator Guide

Appendices

106

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

UserInterface settings

UserInterface TouchPanel DefaultPanel

Define what (contact list, meeting list, or dial pad) the Touch screen control panel will display on wake up.

Requires user role: USER

Value space: <None/LastUsed/ContactList/MeetingList/Dialpad>

None: None of the below options will appear as default on the Touch screen control panel.

LastUsed: The last used (contact list, meeting list, or dial pad) will appear as default on the

Touch screen control panel.

ContactList: The contact list (favorites, directory and history) will appear as default on the

Touch screen control panel.

MeetingList: The list of scheduled meetings will appear as default on the Touch screen control panel.

DialPad: The dial pad will appear as default on the Touch screen control panel.

Example:

UserInterface TouchPanel DefaultPanel: None

UserInterface UserPreferences

Some user preferences (ringtone, volume, language, date and time, etc) can be made available from the Settings menu, or from the Settings > Administrator menu on the Touch screen control panel. Accessing the Administrator menus requires that the user has admin privileges.

Requires user role: ADMIN

Value space: <Off/On>

Off: The user preferences are available from the Settings > Administrator menu on the Touch screen control panel, for users with admin privileges.

On: The user preferences are available from the Settings menu on the Touch screen control panel.

Example:

UserInterface UserPreferences: On

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

107

Setting passwords

Administrator Guide

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface Setting passwords

Administrator Guide

Appendices

Video settings

Video AllowWebSnapshots

Allow or disallow snapshots being taken of the local input sources, remote sites and presentation channel. If allowed, the web interface Call Control page will show snapshots both when idle and in a call.

NOTE: This feature is disabled by default, and must be enabled from the on-screen menu, from a directly connected Touch control panel, or via the codec's serial port (COM port).

Requires user role: ADMIN

Value space: <Off/On>

Off: Capturing web snapshots is not allowed.

On: Web snapshots can be captured and displayed on the web interface.

Example:

Video AllowWebSnapshots: Off

Video CamCtrlPip CallSetup Mode

This setting is used to switch on self-view for a short while when setting up a call. The Video

CamCtrlPip CallSetup Duration setting determines for how long it remains on. This applies when self-view in general is switched off.

Requires user role: ADMIN

Value space: <Off/On>

Off: self-view is not shown automatically during call setup.

On: self-view is shown automatically during call setup.

Example:

Video CamCtrlPip CallSetup Mode: Off

Video CamCtrlPip CallSetup Duration

This setting only has an effect when the Video CamCtrlPip CallSetup Mode setting is switched

On. In this case, the number of seconds set here determines for how long self-view is shown before it is automatically switched off.

Requires user role: ADMIN

Value space: <1..60>

Range: Choose for how long self-view remains on. The valid range is between 1 and 60 seconds.

Example:

Video CamCtrlPip CallSetup Duration: 10

Video DefaultPresentationSource

Define which video input source shall be used as the default presentation source when you press the Presentation key on the remote control. If using the Touch screen control panel this setting has no effect. The Video Input Source n Connector setting defines which input connector to use for input source n.

Requires user role: USER

Value space: <1/2/3>

Range: Select the video source to be used as the presentation source.

Example:

Video DefaultPresentationSource: 3

Video Input DVI [3]/[2,3] RGBQuantizationRange

NOTE: Codec C40 has one DVI input (DVI-I 3). Codec C60 has two DVI inputs (DVI-I 2 and 3).

All devices with DVI inputs should follow the rules for RGB video quantization range defined in

CEA-861. Unfortunately some devices do not follow the standard and this configuration may be used to override the settings to get a perfect image with any source. The default value is set to

Full because most DVI sources expects full quantization range.

Requires user role: ADMIN

Value space: <Auto/Full/Limited>

Auto: RGB quantization range is automatically selected based on video format according to

CEA-861-E. CE video formats will use limited quantization range levels. IT video formats will use full quantization range levels.

Full: Full quantization range. The R, G, B quantization range includes all code values (0 -

255). This is defined in CEA-861-E.

Limited: Limited Quantization Range. R, G, B quantization range that excludes some code values at the extremes (16 - 235). This is defined in CEA-861-E.

Example:

Video Input 1 DVI 3 RGBQuantizationRange: Full

108

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface Setting passwords

Administrator Guide

Appendices

Video Input DVI [3]/[2,3] Type

NOTE: Codec C40 has one DVI input (DVI-I 3). Codec C60 has two DVI inputs (DVI-I 2 and 3).

The official DVI standard supports both digital and analog signals. In most cases the default

AutoDetect setting can detect whether the signal is analog RGB or digital. However, in some rare cases when DVI-I cables are used (these cables can carry both the analog and digital signals) the auto detection fails. This setting makes it possible to override the AutoDetect and select the correct DVI video input.

This setting should also be used if the video input is an analog component (YPbPr) type signal.

This is used by some cameras (Sony EVI-HD1) and DVD/Blu-ray players. Since it is not possible to auto detect the difference between AnalogRGB and AnalogYPbPr, the AnalogYPbPr setting must be selected.

Requires user role: ADMIN

Value space: <AutoDetect/Digital/AnalogRGB/AnalogYPbPr>

AutoDetect: Set to AutoDetect to automatically detect if the signal is analog RGB or digital.

Digital: Set to Digital to force the DVI video input to Digital when using DVI-I cables with both analog and digital pins and AutoDetect fails.

AnalogRGB: Set to AnalogRGB to force the DVI video input to AnalogRGB when using DVI-I cables with both analog and digital pins and AutoDetect fails.

AnalogYPbPr: Set to AnalogYPbPr to force the DVI video input to AnalogYPbPr, as the component (YPbPr) signal cannot be auto detected.

Example:

Video Input DVI 3 Type: AutoDetect

Video Input HDMI [1..2] RGBQuantizationRange

All devices with HDMI inputs should follow the rules for RGB video quantization range defined in

CEA-861. Unfortunately some devices do not follow the standard and this configuration may be used to override the settings to get a perfect image with any source.

Requires user role: ADMIN

Value space: <Auto/Full/Limited>

Auto: RGB quantization range is automatically selected based on the RGB Quantization

NOTE: Codec C40 has one DVI input (DVI-I 3). Codec C60 has two DVI inputs (DVI-I 2 and 3).

Select which video input connector to be active on video input source 2.

Requires user role: ADMIN

Value space: <HDMI/DVI>

HDMI: Select HDMI when you want to use the HDMI 2 as input source 2.

DVI: Select DVI-I when you want to use the DVI-I 2 as input source 2.

Example:

Video Input Source 2 Connector: HDMI

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface Setting passwords

Administrator Guide

Appendices

Video Input Source [3] Connector

NOTE: Codec C40 has one DVI input (DVI-I 3). Codec C60 has two DVI inputs (in this context, use DVI-I 3).

Select which video input connector to be active on video input source 3.

Requires user role: ADMIN

Value space: <DVI/Composite/YC>

DVI: Select DVI when you want to use the DVI-I 3 as input source 3.

Composite: Select Composite when you want to use the Composite as input source 3.

YC: Select YC when you want to use the S-Video (YC) as input source 3. Connect to the two connectors marked Y/Comp and C.

Example:

Video Input Source 3 Connector: DVI

Video Input Source [1..3] Type

Set which type of input source is connected to the video input.

Requires user role: ADMIN

Value space: <other/camera/PC/DVD/document_camera>

Other: Select Other when some other type of equipment is connected to the selected video input.

Camera: Select Camera when you have a camera connected to the selected video input.

PC: Select PC when you have a PC connected to the selected video input.

DVD: Select DVD when you have a DVD player connected to the selected video input.

Document_Camera: Select Document_Camera when you have a document camera connected to the selected video input.

Example:

Video Input Source 1 Type: PC

Video Input Source [1..3] PresentationSelection

Define how the video system will behave when a presentation source is connected to the video input. In general, any input source can be used as a presentation source; normally, the main camera (self-view) will not be used as a presentation source. Note that sharing the presentation with the far end always requires additional action (tap Start Presenting on the Touch screen control panel, or press the Presentation key on the remote control).

Requires user role: ADMIN

Value space: <Manual/Automatic/OnConnect/Hidden>

Manual: In manual mode (default value), the contents of the input source will not be presented on the screen until you select it. Use either the remote control or the Touch screen control panel to choose which input source to present.

Automatic: In automatic mode, the content on the input source will be presented on screen automatically. If more than one source is set to Automatic, the last connected source will be used. If any content was active (presented) when the call was disconnected, the content will still be displayed locally.

OnConnect: When in on-connect mode, the content on the input source will be presented on screen when a cable is connected. Otherwise, the behavior is like when in manual mode.

Hidden: In hidden mode, the contents of the input source do not appear in the graphical user interface.

Example:

Video Input Source 1 PresentationSelection: Manual

Video Input Source [1..3] Visibility

Define the visibility of the video input source in the menus on the user interface.

Requires user role: ADMIN

Value space: <Never/Always/IfSignal>

Never: Set to Never when the input source is not expected to be used as a presentation source.

Always: When set to Always, the menu selection for the video input source will always be visible on the graphical user interface.

IfSignal: When set to IfSignal, the menu selection for the video input source will only be visible when a presentation source is connected to the video input.

Example:

Video Input Source 1 Visibility: IfSignal

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

Video Input Source [1..3] CameraControl Mode

Select whether or not to enable camera control for the selected video input source when the video input is active.

Requires user role: ADMIN

Value space: <Off/On>

Off: Disable camera control.

On: Enable camera control.

Example:

Video Input Source 1 CameraControl Mode: On

Video Input Source [1..3] CameraControl CameraId

Select the ID of the camera in the Visca chain that is connected to this camera source. The

CameraId setting represents the camera's position in the Visca chain.

Requires user role: ADMIN

Value space: <1/2/3/4/5/6/7>

Range: Select the ID of the camera in the Visca chain.

Example:

Video Input Source 1 CameraControl CameraId: 1

Administrator Guide

Appendices Setting passwords

Video Input Source [1..3] OptimalDefinition Profile

The Video Input Source Quality setting must be set to Motion for the optimal definition settings to take any effect.

The optimal definition profile should reflect the lighting conditions in your room and the quality of the video input (camera); the better the lighting conditions and video input, the higher the profile. Then, in good lighting conditions, the video encoder will provide better quality (higher resolution or frame rate) for a given call rate.

Generally, we recommend using the Normal or Medium profiles. However, when the lighting conditions are good, the High profile can be set in order to increase the resolution for a given call rate.

Some typical resolutions used for different optimal definition profiles, call rates and transmit frame rates are shown in the table below. It is assumed that dual video is not used. The resolution must be supported by both the calling and called systems.

Use the Video Input Source OptimalDefinition Threshold60fps setting to decide when to use the

60 fps frame rate.

Typical resolutions used for different optimal definition profiles, call rates and frame rates

Frame rate

Optimal

Definition

Profile

Call rate

256 kbps 768 kbps 1152 kbps 1472 kbps 2560 kbps 4 Mbps 6 Mbps

30 fps

Normal

Medium

512 × 288 1024 × 576 1280 × 720 1280 × 720 1920 × 1080 1920 × 1080 1920 × 1080

640 × 360 1280 × 720 1280 × 720 1280 × 720 1920 × 1080 1920 × 1080 1920 × 1080

High

Normal

768 × 448 1280 × 720 1280 × 720 1920 × 1080 1920 × 1080 1920 × 1080 1920 × 1080

256 × 144 512 × 288 768 × 448 1024 × 576 1280 × 720 1280 × 720 1280 × 720

60 fps Medium

256 × 144 768 × 448 1024 × 576 1024 × 576 1280 × 720 1280 × 720 * 1280 × 720 *

High

512 × 288 1024 × 576 1280 × 720 1280 × 720 1280 × 720

1280 × 720

The resolution will be 1920 × 1080 for 1080p60 capable C60 codecs (main board rev F and later).

Requires user role: ADMIN

Value space: <Normal/Medium/High>

Normal: Use this profile for a normally to poorly lit environment. Resolutions will be set rather conservative.

Medium: Requires good and stable lighting conditions and a good quality video input. For some call rates this leads to higher resolution.

High: Requires nearly optimal video conferencing lighting conditions and a good quality video input in order to achieve a good overall experience. Rather high resolutions will be used.

Example:

Video Input Source 1 OptimalDefinition Profile: Normal

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface Setting passwords

Administrator Guide

Appendices

Video Input Source [1..3] OptimalDefinition Threshold60fps

For each video input, this setting tells the system the lowest resolution where it should transmit

60fps. So for all resolutions lower than this, the maximum transmitted frame rate would be

30fps, while above this resolution 60fps would also be possible, if the available bandwidth is adequate.

Requires user role: ADMIN

Value space: <512_288/768_448/1024_576/1280_720/1920_1080/Never>

512_288: Set the threshold to 512x288.

768_448: Set the threshold to 768x448.

1024_576: Set the threshold to 1024x576.

1280_720: Set the threshold to 1280x720.

1920_1080: Set the threshold to 1920x1080.

Never: Do not set a threshold for transmitting 60fps.

Example:

Video Input Source 1 OptimalDefinition Threshold60fps: 1280 _ 720

Video Input Source [1..3] Quality

When encoding and transmitting video there will be a trade-off between high resolution and high frame rate. For some video sources it is more important to transmit high frame rate than high resolution and vice versa. The Quality setting specifies whether to give priority to high frame rate or to high resolution for a given source.

Video Layout Engine LocalMode

Sets the operating mode of the built-in layout engine.

Requires user role: ADMIN

Value space: <Disabled/Enabled/DisabledPIPs>

Disabled: The built-in layout engine does not display any frames in the layout on the local output.

Enabled: The built-in layout engine displays all frames in the layout on all local outputs.

DisabledPIPs: The built-in layout engine does not display any PIP frame in the layout on the local output.

Example:

Video Layout Engine LocalMode: Enabled

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface Setting passwords

Administrator Guide

Appendices

Video Layout LocalLayoutFamily

Select which video layout family to use locally.

Requires user role: ADMIN

Value space: <Auto/FullScreen/Equal/PresentationSmallSpeaker/PresentationLargeSpeaker/

Prominent/Overlay/Single>

Auto: The default layout family, as given by the layout database, will be used as the local layout. For more information about the layout database, see the xCommand Video Layout

LoadDb command.

FullScreen: The FullScreen layout family will be used as the local layout. It means that the active speaker or presentation will be shown in full screen. Using this value is not recommended as from TC6.0.

Equal: The Equal layout family will be used as the local layout. All videos have equal size, as long as there is space enough on the screen(s).

PresentationSmallSpeaker: The PresentationSmallSpeaker layout family will be used as the local layout. Using this value is not recommended as from TC6.0.

PresentationLargeSpeaker: The PresentationLargeSpeaker layout family will be used as the local layout. Using this value is not recommended as from TC6.0.

Prominent: The Prominent layout family will be used as the local layout. The active speaker, or the presentation if present, will be a large picture, while the other participants will be small pictures. Transitions between active speakers are voice switched.

Overlay: The Overlay layout family will be used as the local layout. The active speaker, or the presentation if present, will be shown in full screen, while the other participants will be small pictures-in-picture (PiP). Transitions between active speakers are voice switched.

Single: The active speaker, or the presentation if present, will be shown in full screen. The other participants are not shown. Transitions between active speakers are voice switched.

Example:

Video Layout LocalLayoutFamily: Auto

Video Layout PresentationDefault View

Determine how the presentation will show on screen when you start sharing a presentation.

Requires user role: ADMIN

Value space: <Default/Minimized/Maximized>

Default: The presentation is a part of the layout.

Minimized: The presentation starts up in PIP mode.

Maximized: The presentation starts up in full screen mode.

Example:

Video Layout PresentationDefault View: Default

Video Layout RemoteLayoutFamily

Select which video layout family to be used for the remote participants.

Requires user role: ADMIN

Value space: <Auto/FullScreen/Equal/PresentationSmallSpeaker/PresentationLargeSpeaker/

Prominent/Overlay/Single>

Auto: The default layout family, as given by the local layout database, will be used as the remote layout. For more information about the layout database, see the command: xCommand Video Layout LoadDb.

FullScreen: The FullScreen layout family will be used as the remote layout. It means that the active speaker or presentation will be shown in full screen. Using this value is not recommended as from TC6.0.

Equal: The Equal layout family will be used as the remote layout. All videos have equal size, as long as there is space enough on the screen.

PresentationSmallSpeaker: The PresentationSmallSpeaker layout family will be used as the remote layout. Using this value is not recommended as from TC6.0.

PresentationLargeSpeaker: The PresentationLargeSpeaker layout family will be used as the remote layout. Using this value is not recommended as from TC6.0.

Prominent: The Prominent layout family will be used as the remote layout. The active speaker, or the presentation if present, will be a large picture, while the other participants will be small pictures. Transitions between active speakers are voice switched.

Overlay: The Overlay layout family will be used as the remote layout. The active speaker, or the presentation if present, will be shown in full screen, while the other participants will be small pictures-in-picture (PiP). Transitions between active speakers are voice switched.

Single: The active speaker, or the presentation if present, will be shown in full screen. The other participants are not shown. Transitions between active speakers are voice switched.

Example:

Video Layout RemoteLayoutFamily: Auto

Video Layout Scaling

Define how the system shall adjust the aspect ratio for images or frames when there is a difference between the image and the frame it is to be placed in.

Requires user role: ADMIN

Value space: <Off/On>

Off: No adjustment of the aspect ratio.

On: Let the system automatically adjust aspect ratio.

Example:

Video Layout Scaling: On

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface Setting passwords

Administrator Guide

Appendices

Video Layout ScaleToFrame

Define what to do if the aspect ratio of a video input source doesn't match the aspect ratio of the corresponding image frame in a composition. For example if you have a 4:3 input source

(like XGA) to be displayed on a 16:9 output (like HD720).

Requires user role: ADMIN

Value space: <Manual/MaintainAspectRatio/StretchToFit>

Manual: If the difference in aspect ratio between the video input source and the target image frame is less than the Video Layout ScaleToFrameThreshold setting (in percent), the image is stretched to fit. If not, the system will maintain the original aspect ratio.

MaintainAspectRatio: Maintain the aspect ratio of the input source, and fill in black in the rest of the frame (letter boxing or pillar boxing).

StretchToFit: Stretch (horizontally or vertically) the input source to fit into the image frame.

NOTE: The general limitation is that you cannot upscale in one direction and at the same time downscale in the other direction. In such situations the codec will apply letterboxing.

Example:

Video Layout ScaleToFrame: MaintainAspectRatio

Video Layout ScaleToFrameThreshold

Only applicable if the Video Layout ScaleToFrame setting is set to manual. If the difference in aspect ratio between the video input source and the target image frame is less than the

ScaleToFrameThreshold setting (in percent), the image is stretched to fit. If not, the system will maintain the original aspect ratio.

Requires user role: ADMIN

Value space: <0..100>

Range: Select a value from 0 to 100 percent.

Example:

Video Layout ScaleToFrameThreshold: 5

Video PIP ActiveSpeaker DefaultValue Position

Determine the position on screen of the active speaker picture-in-picture (PiP). The setting only takes effect when using a video layout where the active speaker is a PiP, i.e. the Overlay layout, or possibly a Custom layout (see the Video Layout LocalLayoutFamily setting). The setting takes effect from the next call onwards; if changed during a call, it will have no effect on the current call.

Requires user role: ADMIN

Value space: <Current/UpperLeft/UpperCenter/UpperRight/CenterLeft/CenterRight/LowerLeft/

LowerRight>

Current: The position of the active speaker PiP will be kept unchanged when leaving a call.

UpperLeft: The active speaker PiP will appear in the upper left corner of the screen.

UpperCenter: The active speaker PiP will appear in the upper center position.

UpperRight: The active speaker PiP will appear in the upper right corner of the screen.

CenterLeft: The active speaker PiP will appear in the center left position.

CentreRight: The active speaker PiP will appear in the center right position.

LowerLeft: The active speaker PiP will appear in the lower left corner of the screen.

LowerRight: The active speaker PiP will appear in the lower right corner of the screen.

Example:

Video PIP ActiveSpeaker DefaultValue Position: Current

Video PIP Presentation DefaultValue Position

Determine the position on screen of the presentation picture-in-picture (PiP). The setting only takes effect when the presentation is explicitly minimized to a PiP, for example using the remote control or the Touch screen control panel. The setting takes effect from the next call onwards; if changed during a call, it will have no effect on the current call.

Requires user role: ADMIN

Value space: <Current/UpperLeft/UpperCenter/UpperRight/CenterLeft/CenterRight/LowerLeft/

LowerRight>

Current: The position of the presentation PiP will be kept unchanged when leaving a call.

UpperLeft: The presentation PiP will appear in the upper left corner of the screen.

UpperCenter: The presentation PiP will appear in the upper center position.

UpperRight: The presentation PiP will appear in the upper right corner of the screen.

CenterLeft: The presentation PiP will appear in the center left position.

CentreRight: The presentation PiP will appear in the center right position.

LowerLeft: The presentation PiP will appear in the lower left corner of the screen.

LowerRight: The presentation PiP will appear in the lower right corner of the screen.

Example:

Video PIP Presentation DefaultValue Position: Current

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

Video Selfview

Determine if the main video source (self-view) shall be displayed on screen.

This setting is obsoleted by the Video SelfviewDefault Mode setting.

Requires user role: USER

Value space: <Off/On>

Off: Do not display self-view on screen.

On: Display self-view on screen.

Example:

Video Selfview: On

Video SelfviewPosition

Select where the small self-view PiP (Picture-in-Picture) will appear on screen.

This setting is obsoleted by the Video SelfviewDefault PIPPosition setting.

Requires user role: ADMIN

Value space: <UpperLeft/UpperCenter/UpperRight/CenterLeft/CenterRight/LowerLeft/

LowerRight>

UpperLeft: The self-view PiP will appear in the upper left corner of the screen.

UpperCenter: The self-view PiP will appear in the upper center of the screen.

UpperRight: The self-view PiP will appear in the upper right corner of the screen.

CenterLeft: The self-view PiP will appear on the left side of the screen, in center.

CenterRight: The self-view PiP will appear on the right side of the screen, in center.

LowerLeft: The self-view PiP will appear in the lower left corner of the screen.

LowerRight: The self-view PiP will appear in the lower right corner of the screen.

Example:

Video SelfviewPosition: LowerRight

Administrator Guide

Appendices Setting passwords

Video SelfviewDefault Mode

Determine if the main video source (self-view) shall be displayed on screen after a call.

The position and size of the self-view window is determined by the Video SelfviewDefault

PIPPosition and the Video SelfviewDefault FullscreenMode settings respectively.

Requires user role: ADMIN

Value space: <Off/Current/On>

Off: self-view is switched off when leaving a call.

Current: self-view is left as is, i.e. if it was on during the call, it remains on after the call; if it was off during the call, it remains off after the call.

On: self-view is switched on when leaving a call.

Example:

Video SelfviewDefault Mode: Current

Video SelfviewDefault FullscreenMode

Determine if the main video source (self-view) shall be shown in full screen or as a small picture-in-picture (PiP) after a call. The setting only takes effect when self-view is switched on

(see the Video SelfviewDefault Mode setting).

Requires user role: ADMIN

Value space: <Off/Current/On>

Off: self-view will be shown as a PiP.

Current: The size of the self-view picture will be kept unchanged when leaving a call, i.e. if it was a PiP during the call, it remains a PiP after the call; if it was fullscreen during the call, it remains fullscreen after the call.

On: The self-view picture will be shown in fullscreen.

Example:

Video SelfviewDefault FullscreenMode: Current

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface Setting passwords

Administrator Guide

Appendices

Video SelfviewDefault PIPPosition

Determine the position on screen of the small self-view picture-in-picture (PiP) after a call. The setting only takes effect when self-view is switched on (see the Video SelfviewDefault Mode setting) and fullscreen view is switched off (see the Video SelfviewDefault FullscreenMode setting).

Requires user role: ADMIN

Value space: <Current/UpperLeft/UpperCenter/UpperRight/CenterLeft/CenterRight/LowerLeft/

LowerRight >

Current: The position of the self-view PiP will be kept unchanged when leaving a call.

UpperLeft: The self-view PiP will appear in the upper left corner of the screen.

UpperCenter: The self-view PiP will appear in the upper center position.

UpperRight: The self-view PiP will appear in the upper right corner of the screen.

CenterLeft: The self-view PiP will appear in the center left position.

CentreRight: The self-view PiP will appear in the center right position.

LowerLeft: The self-view PiP will appear in the lower left corner of the screen.

LowerRight: The self-view PiP will appear in the lower right corner of the screen.

Example:

Video SelfviewDefault PIPPosition: Current

Video SelfviewDefault OnMonitorRole

Determine which monitor/output to display the main video source (self-view) on after a call.

The value reflects the monitor roles set for the different outputs in the Video Output HDMI/DVI/

Composite MonitorRole settings.

The setting applies both when self-view is displayed in full screen, and when it is displayed as picture-in-picture (PiP), but only if the Video Monitors setting is set to Dual.

Requires user role: ADMIN

Value space: <First/Second/Current>

First: The self-view picture will be shown on outputs with the Video Output HDMI/DVI/

Composite MonitorRole set to First.

Second: The self-view picture will be shown on outputs with the Video Output HDMI/DVI/

Composite MonitorRole set to Second.

Current: When leaving the call, the selfv iew picture will be kept on the same output as during the call.

Example:

Example:

Video OSD WallpaperSelection: On

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface Setting passwords

Administrator Guide

Appendices

Video OSD LanguageSelection

In cases where you want to prevent users from easily changing the language settings from the Settings menu, the language settings can be made available from within the Administrator

Settings menu. The administrator settings can be password protected. The OSD (On Screen

Display) is where you find the menus, dialogs, icons and indicators, and the navigation is done with a remote control.

Define for how long the encryption indicator (a padlock) will be shown on screen. The setting applies to both encrypted and non-encrypted calls, i.e. both to secure and non-secure conferences. The icon for encrypted calls is a locked padlock, and the icon for non-encrypted calls is a crossed out locked padlock.

Requires user role: ADMIN

Value space: <Auto/AlwaysOn/AlwaysOff>

Auto: If the Conference Encryption Mode setting is set to BestEffort and the call is encrypted, the encryption indicator is shown during the first seconds of a call. If the

Conference Encryption Mode setting is set to BestEffort and the call is non-encrypted, the crossed out encryption indicator is shown during the entire call. If the Conference Encryption

Mode setting is NOT set to BestEffort, the encryption indicator is not shown at all.

AlwaysOn: The encryption indicator is displayed on screen during the entire call. This applies to both encrypted and non-encrypted calls for all Conference Encryption Mode settings.

AlwaysOff: The encryption indicator is never displayed on screen. This applies to both encrypted and non-encrypted calls for all Conference Encryption Mode settings.

Example:

Video OSD EncryptionIndicator: Auto

Video OSD MissedCallsNotification

Define if there should be a missed calls notification on screen. The setting only applies when the video system is operated by a remote control and the on-screen menu. When using the

Touch screen control panel the notification dialog box will appear on the Touch screen control panel, and not on the OSD.

Requires user role: ADMIN

Value space: <Off/On>

Off: The OSD will NOT show any indication that there have been any missed calls. This setting is recommended for 3rd party integrations that need full control of what is shown on the OSD.

On: The OSD will show a notification of missed calls.

Example:

Video OSD MissedCallsNotifications: On

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface Setting passwords

Administrator Guide

Appendices

Video OSD AutoSelectPresentationSource

Determine if the presentation source should be automatically selected.

Requires user role: ADMIN

Value space: <Off/On>

Off: Disable automatic selection of the presentation source.

On: Enable automatic selection of the presentation source.

Example:

Video OSD AutoSelectPresentationSource: Off

Video OSD CallSettingsSelection

In cases where you want to prevent users from easily changing the call settings from the

Settings menu, the call settings can be made available from within the Administrator Settings menu. The administrator settings can be password protected. The OSD (On Screen Display) is where you find the menus, dialogs, icons and indicators, and the navigation is done with a remote control.

Video OSD Output

Define which monitor should display the on-screen menus, information and icons. The OSD (On

Screen Display) is where you find the menus, dialogs, icons and indicators, and the navigation is done with a remote control.

Requires user role: ADMIN

Value space: <Auto/1/2>

Auto: The system will detect when a monitor is connected to the video output, and send the

OSD to the first monitor you connect. If you have a multi-monitor setup, and all monitors are connected before switching on the system, the OSD will be sent to the video output with the lowest numbering, starting on Video OSD Output 1. If the OSD does not show on the desired monitor, disconnect all monitors and reconnect the monitors.

Range 1-2: If you want the OSD to be sent to one specific output, select 1 for HDMI 1 output, or select 2 for DVI-I 2 output. Make sure you connect a monitor to the corresponding video output connector.

Example:

Video OSD Output: Auto

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface Setting passwords

Administrator Guide

Appendices

Video OSD InputMethod InputLanguage

The codec can be enabled for Cyrillic input characters in the menus on screen. Requires that

Video OSD InputMethod Cyrillic is set to On.

Requires user role: ADMIN

Value space: <Latin/Cyrillic>

Latin: Latin characters can be entered when using the remote control (default).

Cyrillic: Cyrillic characters can be entered using the remote control. Requires a Cisco

TelePresence Remote Control with Cyrillic fonts.

Example:

Video OSD InputMethod InputLanguage: Latin

Video OSD InputMethod Cyrillic

Set the Cyrillic mode for the menu input language in the menus on screen.

Requires user role: ADMIN

Value space: <Off/On>

Off: Cyrillic mode is NOT available as a menu input language in the menus on screen.

On: Cyrillic mode is available as a menu input language in the menus on screen. This will enable the setting Video OSD InputMethod InputLanguage.

Example:

Video OSD InputMethod Cyrillic: Off

Video OSD LoginRequired

Determine if the system should require the user to login before accessing the menus on screen.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface Setting passwords

Administrator Guide

Appendices

Video Output HDMI [1] MonitorRole

The HDMI monitor role describes which video stream will be shown on the monitor connected to the video output HDMI connector.

Requires user role: ADMIN

Value space: <Auto/First/Second/PresentationOnly/Recorder>

Auto: The system will detect when a monitor is connected and assign a monitor role to it.

The first monitor connected will be assigned monitor role First. In a multi-monitor setup the next monitor will be assigned monitor role Second.

First/Second: Define the role of the monitor in a multi-monitor setup. In a single-monitor setup, there is no difference between First and Second.

PresentationOnly: Show presentation video stream if active, and nothing else.

Recorder: Show all participants, including the local main video. If active, also show the presentation.

Example:

Video Output HDMI 1 MonitorRole: Auto

Video Output HDMI [1] OverscanLevel

Video Output DVI [2] MonitorRole

The DVI monitor role describes which video stream will be shown on the monitor connected to the video output DVI-I connector.

Requires user role: ADMIN

Value space: <Auto/First/Second/PresentationOnly/Recorder>

Auto: The system will detect when a monitor is connected and assign a monitor role to it.

The first monitor connected will be assigned monitor role First. In a multi-monitor setup the next monitors will be assigned monitor role Second.

First/Second: Define the role of the monitor in a multi-monitor setup. In a single-monitor setup, there is no difference between First and Second.

PresentationOnly: Show presentation video stream if active, and nothing else.

Recorder: Show all participants, including the local main video. If active, also show the presentation.

Example:

Video Output DVI 2 MonitorRole: Auto

Video Output DVI [2] OverscanLevel

Requires user role: ADMIN

Value space: <None/Medium/High>

None: The system will use all of the output resolution.

Medium: The system will not use the outer 3% of the output resolution.

High: The system will not use the outer 6% of the output resolution.

Example:

Video Output DVI 2 OverscanLevel: None

Video Output DVI [2] Resolution

Select the preferred resolution for the monitor connected to the video output DVI-I connector.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

122

Setting passwords

Administrator Guide

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

Experimental settings

The Experimental settings are for testing only and should not be used unless agreed with Cisco.

These settings are not documented and WILL change in later releases.

Setting passwords

Administrator Guide

Appendices

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface System settings

Administrator Guide

Appendices

Chapter 4

Setting passwords

124

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface System settings

Setting the system password

The system password protects the video system. You have to sign in to be able to use the web and command line interfaces, and to get access to the Administrator settings from a Touch 8 control panel.

The admin user

The video system is delivered with a default user account with full credentials. The user name is admin, and initially, no password is set for the default user.

We strongly recommend that you set a password for the admin user in order to restrict access to system configuration. Also set a password for any other user with similar credentials.

Make sure to keep a copy of the password in a safe place. You have to factory reset the unit if you have forgotten the password.

A warning, saying that the system password is not set, is shown on screen until a password is set for the admin user.

About access to administrator settings when using a remote control and the on-screen menu

Note that the on-screen Administrator Settings menu that is available when using a remote control, is NOT protected by the system password; you have to set a menu password (see next page).

Other user accounts

You can create as many user accounts as you like for your video system.

You can read more about how to create and manage user

accounts in the ► User administration

section.

Changing your own system password

Perform the following steps to change the system password.

If a password is currently not set, use a blank

Current password

; to remove a password, leave the

New password

fields blank.

1. Sign in to the web interface with your user name and current password.

2. Click your user name in the upper right corner and choose

Change password

in the drop down menu.

3. Enter the

Current password

, the

New password

, and repeat the new password in the appropriate input fields.

The password format is a string with 0–64 characters.

4. Click

Change password

Administrator Guide

Appendices

Changing another user’s system password

If you have administrator access rights, you can change all users’ passwords by performing the following steps:

1. Sign in to the web interface with your user name and password.

2. Go to the

Maintenance

tab and select

User

Administration

3. Choose the appropriate user from the list.

4. Enter a new password and PIN code.

5. Click

Save

125

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface System settings

Administrator Guide

Appendices

Setting the menu password

The menu password protects the Administrator Settings menu that is available on-screen when using the remote control.

When starting up the video conference system for the first time anyone can access these settings, because the menu password is not set.

We strongly recommend that you set a menu password, because the administrator settings may severely affect the behavior of the system.

Note that the menu password, as from software version

TC7.0, applies only to the on-screen Administrator Settings menu; it does not apply to the Administrator menu on the

Touch 8 controller.

Setting the menu password from the web interface

1. Sign in to the web interface with your user name and current password.

2. Go to

Configuration > System Configuration

3. Click

Set/Change Administrator Settings menu password

to open the menu password dialog.

4. Enter the password in the input field.

5. Click

Save

to set/change the password.

Use the remote control and on-screen menu, or the

Touch controller to find the IP address (IPv4 or IPv6).

Remote control and on-screen menu: Navigate to

Home > Settings > System information

Touch controller: Tap the upper, left corner of the

Touch controller to open the drop down window. Then tap

Settings > System Information

Setting the menu password using the remote control

1. In the on screen menu, go to

Home > Settings >

Administrator settings > Set menu password

The password should be a string with 0–255 characters.

To deactivate the password leave the password input field empty.

2. Enter the menu password in the input field. The password you enter is hidden; each character is replaced with a star

(*).

On the remote control, press the # key to toggle between lower or upper case characters and numbers: abc/

ABC/123.

3. Select

Save

to save the changes, or

Cancel

to leave without saving.

4. Press

Home

( ) to exit.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface System settings

Setting a root password

You can protect the file system of your video system by setting a password for the root user.

The root user is disabled by default. You have to use the command line interface to enable the root user and set a root password.

Activate the root user and set the password

Perform the following steps to activate the root user and set a password for it:

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface System settings Setting passwords

Administrator Guide

About monitors when you have a

Codec C60

Connecting the main monitor

The main monitor can be connected to video output HDMI 1

(the default connector for the main monitor) or DVI-I 2.

The codec will read the native resolution of the monitor and output this if possible. Typically this will give the best possible picture for the connected monitor. If auto fails, you will have to select the resolution manually using the

Video > Output >

HDMI 1 > Resolution

and

Video > Output > DVI 2 > Resolution

settings.

Connecting to HDMI 1

When connecting the main monitor to HDMI 1 the menu, icons and other information on screen (OSD - on screen display) will be displayed on the monitor automatically. This is because HDMI 1 is the default video output of the codec.

Connecting to DVI-I 2

When connecting the main monitor to the DVI–I 2 output, the menus, icons and other information are not automatically displayed on screen. You must move the OSD to the chosen output.

The video outputs of Codec C60

DVI-I 2

HDMI 1 (the default connector for the main monitor)

Moving the OSD

You can move the OSD using the remote control or the web interface.

Remote control

Check which connector the main monitor is connected to, and run the following key sequence on the remote control.

•

Disconnect * # * # 0

x # x=1 (HDMI 1) x=2 (DVI–I 2)

Example: Setting DVI-I 2 as the OSD output.

–

Web interface

Open the System Configuration page. Go to

Video > OSD > Output

and choose the video output connector for the main monitor.

Dual monitors

When you want to run a dual monitor setup, connect the main monitor to video output HDMI 1 and the second monitor to video output DVI-I 2 on the codec.

Dual monitor configuration

To distribute the layout on the two monitors, go to

Advanced configuration (menu on screen) or open the

System Configuration page (web interface). Then go to

Video > Monitors

and choose Dual.

130

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface System settings Setting passwords

Administrator Guide

About monitors when you have a

Codec C40

Connecting the main monitor

The main monitor can be connected to video output HDMI 1

(the default connector for the main monitor) or DVI-I 2.

Video > Output >

HDMI 1 > Resolution

and

Video > Output > DVI 2 > Resolution

settings.

Connecting to HDMI 1

Connecting to DVI-I 2

When connecting the main monitor to the DVI–I 2 output, the menus, icons and other information are not automatically displayed on screen. You must move the OSD to the chosen output.

The video outputs of Codec C40

DVI-I 2

HDMI 1 (the default connector for the main monitor)

Moving the OSD

You can move the OSD using the remote control or the web interface.

Remote control

Check which connector the main monitor is connected to, and run the following key sequence on the remote control.

•

Disconnect * # * # 0

x # x=1 (HDMI 1) x=2 (DVI–I 2)

Example: Setting DVI-I 2 as the OSD output.

–

Web interface

Open the System Configuration page. Go to

Video > OSD > Output

and choose the video output connector for the main monitor.

Dual monitors

When you want to run a dual monitor setup, connect the main monitor to video output HDMI 1 and the second monitor to video output DVI-I 2 on the codec.

Dual monitor configuration

To distribute the layout on the two monitors, go to

Advanced configuration (menu on screen) or open the

System Configuration page (web interface). Then go to

Video > Monitors

and choose Dual.

131

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

Connecting the Cisco

TelePresence Touch 8 controller

The Cisco TelePresence Touch 8 controller is an alternative to the remote control and on screen menus.

When a Touch controller is connected to the codec, the remote control cannot be used. You have to disconnect

(unpair) the Touch controller in order to to use the remote control.

Touch 8 can can be used with a C Series codec running software version TC4.1 or later.

System settings

Power adapter

Setting passwords

Administrator Guide

Option A: To LAN socket (Ethernet)

Option B: To codec 2 nd

Ethernet port

To power socket

Connecting the Touch controller

There are two options how to connect the Touch controller to the codec. In both cases the connection is via the provided power adapter, as illustrated above.

A. Connecting the Touch controller to the codec via LAN.

To enable this mode of operation make sure that the

NetworkServices > SSH > Mode

* setting is turned On.

The process of associating the Touch controller to the codec is called paring. The codec is signalling that it is available for pairing for 30 minutes after it is switched on.

We recommend that the Touch controller and video system is kept on the same subnet.

B. Connecting the Touch controller directly to the codec’s second Ethernet port.

To enable this mode of operation use the remote control and navigate to

Home > Settings > Administrator settings

> Pairing > Direct pairing

and choose On.

Alternatively, set the

NetworkPort 2 > Mode

setting to

DirectPairing.

Restart the codec for the change to take effect.

Codec address

Touch controller set-up

Once the Touch controller is connected to power, the set-up procedure begins. Follow the instructions on screen.

If you have connected the unit to the codec via LAN, you have to choose which codec to pair with. If the codec is not in the list of available codecs displayed on the Touch controller, you can choose a codec manually by entering its IP address.

If the Touch controller needs software upgrade, new software will be downloaded from the codec and installed on the unit automatically as part of the set-up procedure. The Touch controller restarts after the upgrade.

You can verify that the Touch controller is successfully paired to the codec by checking that the codec address is displayed in the top banner.

If you want more details on Touch installation, please read the

Cisco TelePresence Touch 8 inch Installation Guide, which is available on the Cisco web site.

You will find this setting in the Advanced Configuration on-screen menu (remote control) or in the System Configuration page on the web interface.

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

Advanced customization of video and audio

The codec supports full customization of the audio routing and video layouts/templates allowing support for advanced meeting room setups and integrations.

The TC Console application, which is a free software tool that runs on PC/Mac, provides a graphical interface to the advanced customizable features of the codec. TC Console includes the following modules:

Video compositor

• Modify the default video compositing behavior of the codec

• Add new layouts

• Change the automatically chosen layout

• Control what video sources are shown where and when

Audio console

• Configure the audio system of the codec.

• Change the default mixing, routing and equalizers

• Set various input and output connector properties

GPIO

• Change the behavior of the GPIO, i.e. what the codec should do when pins go high/low

For more details about the functionality, see the user guide included in the TC Console application itself or download the TC Console user guide from

► http://www.cisco.com/go/cseries-docs

How to obtain the TC Console application

Download the TC Console application for free from the Cisco Developer Network (CDN) web site. Go to:

► http://developer.cisco.com/web/telepresence-developer

Video compositor

System settings

GPIO

Setting passwords

Audio console

Administrator Guide

133

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface System settings Setting passwords

Administrator Guide

Optimal definition profiles

Under ideal lighting conditions the bandwidth (call rate) requirements can be substantially reduced.

The optimal definition profile should reflect the lighting conditions in your room and the quality of the video input

(camera); the better the lighting conditions and video input, the higher the profile. Then, in good lighting conditions, the video encoder will provide better quality (higher resolution or frame rate) for a given call rate.

In general, we recommend the optimal definition profile set to Normal. However, if lighting conditions are good we recommend that you test the endpoint on the various Optimal

Definition Profile settings before deciding on a profile.

Go to System Configuration on the web interface and navigate to

Video > Input > Source [1..n] > OptimalDefinition >

Profile

to choose the preferred optimal definition profile.

You can set a resolution threshold to determine when to allow sending video at 60 fps. For all resolutions lower than this threshold, the maximum transmitted frame rate will be 30 fps; for higher resolutions, 60 fps will be possible if the available bandwidth is adequate.

Go to System Configuration on the web interface and navigate to

Video > Input > Source [1..n] > OptimalDefinition >

Threshold60fps

to set the threshold.

The video input quality settings must be set to Motion for the optimal definition settings to take any effect. With the video input quality set to Sharpness, the endpoint will transmit the highest resolution possible, regardless of frame rate.

Go to System Configuration on the web interface and navigate to

Video > Input > Source [1..n] > Quality

to set the video quality parameter to Motion.

You can read more about the video settings in the

► System settings

chapter.

High

Typically used in dedicated video conferencing rooms. Requires very good lighting conditions and a good quality video input to achieve a good overall experience.

Under ideal conditions the bandwidth requirements can be reduced by up to

50% compared to Normal.

Medium

Typically used in rooms with good and stable lighting conditions and a good quality video input.

The bandwidth requirements can be reduced by up to 25% compared to

Normal.

Normal

This setting is typically used in office environments where the room is normally to poorly lit.

Typical resolutions used for different optimal definition profiles, call rates and frame rates

Frame rate

Optimal

Definition

Profile

Call rate

30 fps

Normal

Medium

256 kbps 768 kbps 1152 kbps 1472 kbps 2560 kbps 4 Mbps

512 × 288

640 × 360

6 Mbps

1024 × 576 1280 × 720 1280 × 720 1920 × 1080 1920 × 1080 1920 × 1080

1280 × 720 1280 × 720 1280 × 720 1920 × 1080 1920 × 1080 1920 × 1080

High

Normal

Medium

768 × 448 1280 × 720 1280 × 720 1920 × 1080 1920 × 1080 1920 × 1080 1920 × 1080

256 × 144 512 × 288 768 × 448 1024 × 576 1280 × 720 1280 × 720 1280 × 720

256 × 144 768 × 448 1024 × 576 1024 × 576 1280 × 720 1280 × 720

1280 × 720

60 fps

High

512 × 288 1024 × 576 1280 × 720 1280 × 720 1280 × 720 * 1280 × 720 * 1280 × 720

The resolution will be 1920 × 1080 for 1080p60 capable C60 codecs (main board rev F and later).

134

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

ClearPath — Packet loss resilience

ClearPath introduces advanced packet loss resilience mechanisms that increase the experienced quality when you use your video system in an error prone environment.

We recommend that you keep ClearPath enabled on your video system.

Go to Advanced configuration (menu on screen) or open the

System Configuration page (web interface):

• Navigate to

Conference 1 > PacketLossResilience > Mode

Choose Off to disable ClearPath and On to enable

ClearPath.

System settings Setting passwords

Administrator Guide

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

Requirement for speaker systems connected to a Cisco

TelePresence C Series codec

Cisco has put in a lot of effort to minimize the camera to screen delay on our TelePresence endpoints.

New consumer TVs are usually equipped with “Motion Flow” or similar technology to insert new video frames between standard frames to create smoother images. This processing takes time and to maintain lip synchronization, the TV will delay the audio so that the audio and video arrives at the same time.

The echo canceller in the Cisco endpoints can handle such delay up to 30 ms. Many consumer TVs are not made for real time video communication and may introduce more than

30 ms of delay.

If you use such a TV together with a C Series codec it is recommended that you turn off “Motion Flow”, “Natural

Motion” or any other video processing that introduces additional delay.

Some consumer TVs also support advanced audio processing like “Virtual Surround” effects and “Dynamic

Compression” to improve the TV experience. Such processing will make any acoustic echo canceller malfunction and should hence be switched off.

Some monitors are equipped with a setting called ‘Game

Mode’. This mode is specifically designed to help reduce the response time and will usually help to reduce the delay.

System settings Setting passwords

Administrator Guide

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

DNAM for

Profile 42”/52”/55”

The DNAM (Digital Natural Audio Module) is built on two specially designed and separate modules: the amplifier and the loudspeaker cabinet.

DNAM loudspeaker

The DNAM loudspeaker

3-way center loudspeaker system

• Frequency range 50 Hz - 20 kHz

• 2 × 100 mm low- and midrange loudspeaker 8 ohm nominal, excellent quality (SEAS Prestige series)

• 1 × 25 mm dome tweeter, 6 ohm nominal, excellent quality

• Digitally filtered audio signals received from DNAM amplifier

• Long time max power 70 watt on all loudspeakers

• Enclosed MDF loudspeaker cabinet

Integrated stereo loudspeaker

Each side has:

• 1 × 90 mm fullrange loudspeaker, 8 ohm nominal, excellent quality

• Frequency range 70 Hz - 20 kHz

• Enclosed MDF loudspeaker cabinet

DNAM amplifier

Loudspeaker Out

(D-SUB)

Audio In

(RCA)

Audio Loop Out

(RCA)

Power socket

Fuse

System settings

Audio Stereo Out (XLR)

Audio Differential In (XLR)

Setting passwords

Some DNAM amplifier models are delivered without XLR connectors, and with a different RCA connector placement.

Administrator Guide

The DNAM amplifier

• 5 × 50 watt continuous average output power

• Full frequency range for audio

(20 Hz – 20 kHz)

• Digital signal processing and filtering on all channels for best audio detail clarity

• Digital crossover filtering on center channels

• In/out:

Audio In: SPDIF (stereo) or Analog (mono) using the same connector

Audio Loop Out: line out directly from the input; always analog even with SPDIF in

Audio Differential In: female XLR, pinout:

1 - GND, 2 – Signal (+), 3 – Signal (-)

Audio Stereo Out: male XLR, common

GND configuration

Loudspeaker Out: female D-SUB 15-pin

• Fuse 2 A 250 V slow, 5 × 20 mm, Littelfuse type 215002.

Always use this type of fuse. Using a different type may lead to serious hardware malfunction.

Spare fuses

The Profile system is delivered with two spare

DNAM fuses in the column.

Take care not to damage the fuse and fuse holder when replacing a fuse.

• Push the fuse holder slightly inwards and turn counter-clockwise to release the fuse.

• When reinserting the fuse and fuse holder, push slightly inwards and turn the holder carefully clockwise until it locks in place.

137

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

DNAM for Profile 65”

The DNAM (Digital Natural Audio Module) is built on two specially designed and separate modules: the amplifier and the loudspeaker cabinet.

The DNAM loudspeaker

3-way center loudspeaker system

• Frequency range 50 Hz - 20 kHz

• 2 × 100 mm low- and midrange loudspeakers, 8 ohm nominal, reference quality (SEAS Excel series)

• 1 × 25 mm dome tweeter, 6 ohm nominal, excellent quality

• Digitally filtered audio signals received from DNAM amplifier

• Long time max power 70 watt on all loudspeakers

• Enclosed MDF loudspeaker cabinet

2-way integrated stereo loudspeaker

Each side has:

• 1 × 100 mm low- and midrange loudspeaker, 8 ohm nominal, reference quality (SEAS Excel series)

• 1 × 25 mm dome tweeter, 6 ohm nominal, excellent quality

• Passive crossover filter

• Frequency range 70 Hz - 20 kHz

• Long time max power 70 watt

• Enclosed MDF loudspeaker cabinet

DNAM loudspeaker

DNAM amplifier

Audio In (RCA)

Audio Loop Out (RCA)

Audio Differential In (XLR)

Audio Stereo Out (XLR)

System settings

Loudspeaker Out

(D-SUB)

Power socket

Fuse

Setting passwords

Administrator Guide

The DNAM amplifier

• 5 × 50 watt continuous average output power

• Full frequency range for audio

(20 Hz – 20 kHz)

• Digital signal processing and filtering on all channels for best audio detail clarity

• Digital crossover filtering on center channels

• In/out:

Audio In: SPDIF (stereo) or Analog (mono) using the same connector

Audio Loop Out: line out directly from the input; always analog even with SPDIF in

Audio Differential In: female XLR, pinout:

1 - GND, 2 – Signal (+), 3 – Signal (-)

Audio Stereo Out: male XLR, common

GND configuration

Loudspeaker Out: female D-SUB 15-pin

• Fuse 2 A 250 V slow, 5 × 20 mm, Littelfuse type 215002

Always use this type of fuse. Using a different type may lead to serious hardware malfunction.

Spare fuses

The Profile system is delivered with two spare

DNAM fuses in the column.

Take care not to damage the fuse and fuse holder when replacing a fuse.

• Push the fuse holder slightly inwards and turn counter-clockwise to release the fuse.

• When reinserting the fuse and fuse holder, push slightly inwards and turn the holder carefully clockwise until it locks in place.

138

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface System settings

Factory resetting the codec

It is not possible to undo a factory reset.

You should always backup the log files and the current configuration before you factory reset a system.

Open the web interface, sign in, and follow these steps:

• Navigate to

Maintenance > System Recovery

and choose the

Backup

tab.

• Click

Download Logs

and

Download Configuration

Backup

and follow the instructions to save the files on your computer.

If there is a severe problem with the video system, resetting it to its default factory settings should be the last resort.

Always consider reverting to the previously used software version before performing a factory reset. In many situations this will recover the system. Note that both the current and the previous software images reside on the system. Read

about software swapping in the ► System recovery section.

We recommend that you use either a Touch controller or the web interface to factory reset the system. If these interfaces are not available, you can connect to the system’s standard serial interface and issue a factory reset command.

The remote control and on-screen menu do not give access to factory reset.

When factory resetting the video system the following happens:

• The call logs will be deleted.

• Passwords will be reset to default.

• All system parameters will be reset to default values.

• All files that have been uploaded to the system will be deleted. This includes, but is not limited to, custom backgrounds, certificates, and the favorites list (My contacts).

• The previous (inactive) software image will be deleted.

• Release keys and option keys will not be affected.

The system restarts automatically after the reset. It is using the same software image as before.

User interface: Touch

1. Tap gently on the Touch screen if the unit is in sleep mode.

2. Open the

Settings

menu and navigate to

Administrator >

Reset.

You have to log in with an administrator user name and password to access the

Administrator

menu.

3. Tap the

Factory Reset

button.

The system reverts to the default factory settings and restarts automatically. This will take a few minutes.

The system confirms the factory reset by displaying a notification on the main screen when up and running again. The notification disappears after approximately

10 seconds.

User interface: Web

Open the

Settings

menu and tap

System Information

on the Touch controller, or navigate to

Home >

Settings > System information

using the remote control, to find the system’s IP address (IPv4 or IPv6).

1. Open a web browser and enter the IP address of the video system in the address bar.

2. Navigate to

Maintenance > System Recovery

and choose the

Factory Reset

tab.

3. Read the provided information carefully before you click

Perform a factory reset...

4. Click the red

Yes

button to confirm that you want to perform a factory reset.

The system reverts to the default factory settings and restarts automatically. This will take a few minutes.

The system confirms the factory reset by displaying a notification on the main screen when up and running again. The notification disappears after approximately

10 seconds.

Setting passwords

Administrator Guide

Using the serial interface

You have to connect to the video system’s COM port with a serial cable. The serial port is enabled as a default, but it may have been disabled.

The connection parameters for the COM port are as follows:

• Data bits: 8

• Parity: None

• Stop bits: 1

• Flow control: None

• Baud rate: The default value is 38400 bps, but it may have been changed

You can read more about the system’s serial port settings in

the

► System settings

chapter.

1. Login as admin (administrator rights).

2. Issue the following command:

xCommand SystemUnit FactoryReset Confirm: Yes

You will see the following text:

*r FactoryResetResult:

**end

OK

The system will revert to the default factory settings and automatically restart. This will take a few minutes.

The system confirms the factory reset by displaying a notification on the main screen when up and running again. The notification disappears after approximately

10 seconds.

* The

Settings

menu can be accessed from the drop down window that appears when you tap the contact information in the upper, left corner of the Touch controller.

139

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

Factory resetting the Touch 8 control panel

You can reset the Touch 8 control panel to its default factory settings using the New message indicator and the Mute button.

When factory resetting Touch 8 the logs are cleared, and the configuration and pairing information are lost.

Touch 8 restarts after the reset and must receive a new configuration from the video system.

• If Touch 8 is directly connected to the video system it receives the configuration automatically.

• If it is connected via LAN it receives the new configuration as soon as it is successfully paired to the video system.

It is not possible to undo a factory reset.

System settings

1. Locate the

New message indicator

and

Mute

buttons.

The

New message indicator

is a bit hard to see, but it is the button with the exclamation mark on it.

Mute button

New message indicator

2. Press and hold the

New message indicator

until it lights up (approximately 10 seconds).

3. Press the

Mute

button twice.

The Touch controller automatically reverts to the default factory settings and restarts.

Setting passwords

Administrator Guide

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface System settings Setting passwords

Administrator Guide

Technical specifications

Codec C60/C40

UNIT DELIVERED COMPLETE WITH:

• Video conferencing codec, wireless remote control, rack mounting rails (C60), rack mounting ears (C40),

LAN cable, power cable

BANDWIDTH

• H.323/SIP up to 6 Mbps point-to-point

FIREWALL TRAVERSAL

• Cisco TelePresence Expressway technology

• H.460.18, H.460.19 firewall traversal

• SIP ICE (Interactive Connectivity Establishment)

VIDEO STANDARDS

• H.261

• H.263

• H.263+

• H.264

VIDEO FEATURES

• Native 16:9 widescreen

• Advanced screen layouts

• Intelligent video management

• Local auto layout

• 7 embedded individual video compositors — 1 for every output and 1 for every encoder (C60 only) **

VIDEO INPUTS (5 INPUTS (C60) / 4 INPUTS (C40))

Two HDMI inputs; supported formats:

• 1920 × 1080@60, 59.94 Hz (1080p60)

• 1920 × 1080@50 Hz (1080p50)

• 1920 × 1080@30, 29.97 Hz (1080p30)

• 1920 × 1080@25 Hz (1080p25)

• 1920 × 1080@24, 23.97 Hz (1080p24)

• 1280 × 720@60, 59.94 Hz (720p60)

• 1280 × 720@50 Hz (720p50)

• 720 × 480@60, 59.94 Hz (480p60)

• 640 × 480@60 Hz (480p60)

• 1600 × 1200@50, 60 Hz (UXGA)

• 1280 × 1024@60, 75 Hz (SXGA)

• 1024 × 768@60, 70, 75, 85 Hz (XGA)

• 800 × 600@56, 60, 72, 75, 85 Hz (SVGA)

• 1920 × 1200@50, 60 Hz (WUXGA)

• 1680 × 1050@60 Hz (WSXGA+)

• 1440 × 900@60 Hz (WXGA+)

• 1280 × 768@60 Hz (WXGA)

Two (C60), one (C40) × DVI-I inputs; supported formats:

Analog (VGA):

• 1920 × 1080@60 Hz (1080p60)

• 1280 × 720@60 Hz (720p60)

• 1600 × 1200@60 Hz (UXGA)

• 1280 × 1024@60, 75 Hz (SXGA)

• 1280 × 960@60 Hz

• 1024 × 768@60, 70, 75, 85 Hz (XGA)

• 1920 × 1200@50 Hz (WUXGA)

• 1680 × 1050@60 Hz (WSXGA+)

• 1440 × 900@60 Hz (WXGA+)

• 1280 × 800@60 Hz (WXGA)

• 1280 × 768@60 Hz (WXGA)

Analog (YPbPr):

• 1920 × 1080@60 Hz (1080p60)

• 1920 × 1080@50 Hz (1080p50)

• 1920 × 1080@30 Hz (1080p30)

• 1920 × 1080@25 Hz (1080p25)

• 1280 × 720@60 Hz (720p60)

• 1280 × 720@50 Hz (720p50)

• 1280 × 720@30 Hz (720p30)

• 720 × 576@50 Hz (576p50)

• 720 × 480@60 Hz (480p60)

Digital (DVI-D):

• Same as HDMI, ref. above.

One S-video/Composite input (BNC connector):

• PAL/NTSC

• Extended Display Identification Data (EDID)

VIDEO OUTPUTS (3 OUTPUTS (C60) /

2 OUTPUTS (C40))

One HDMI output, one DVI-I output; supported formats:

• 1920 × 1080@60 Hz (1080p60)

• 1280 × 720@60 Hz (720p60)

• 1600 × 1200@60 Hz (UXGA)

• 1280 × 1024@60 Hz (SXGA)

• 1024 × 768@60 Hz (XGA)

• 800 × 600@60 Hz (SVGA)

• 640 × 480@60 Hz (VGA)

• 1920 × 1200@60Hz (WUXGA)

• 1360 × 768@60 Hz

• 1366 × 768@60 Hz

• 1280 × 768@60 Hz (WXGA)

One composite output (BNC connector) (C60 only):

• PAL/NTSC

• VESA Monitor Power Management

• Extended Display Identification Data (EDID)

LIVE VIDEO RESOLUTIONS (ENCODE/DECODE)

• 176 × 144@30 fps (QCIF)

• 352 × 288@30 fps (CIF)

• 512 × 288@30 fps (w288p)

• 576 × 448@30 fps (448p)

• 768 × 448@30 fps (w448p)

• 704 × 576@30 fps (4CIF)

• 1024 × 576@30 fps (w576p)

• 1280 × 720@30 fps (720p30)

• 1920 × 1080@30 fps (1080p30)*

• 640 × 480@30 fps (VGA)

• 800 × 600@30 fps (SVGA)

• 1024 × 768@30 fps (XGA)

• 1280 × 1024@30 fps (SXGA) (C60 only)

• 1280 × 768@30 fps (WXGA)

• 1440 × 900@30 fps (WXGA+)* (C60 only)

• 1680 × 1050@30 fps (WSXGA+)* (C60 only)

• 1600 × 1200@30 fps (UXGA)* (C60 only)

• 1920 × 1200@25fps (WUXGA)* (C60 only)

• 512 × 288@60 fps (w288p60)*

• 768 × 448@60 fps (w448p60)*

• 1024 × 576@60 fps (w576p60)*

• 1280 × 720@60 fps (720p60)*

• 720p30 from 768kbps

• 720p60 from 1152kbps*

• 1080p30 from 1472 kbps*

* Requires option

** Multiwindow compositing not supported on the dual stream

*** Not supported on 4 x zoom camera

AUDIO STANDARDS

• G.711

• G.722

• G.722.1

• G.729AB

• 64 kbps and 128 kbps AAC-LD, mono and stereo

AUDIO FEATURES

• CD quality 20 kHz mono and stereo

• Four (C60) / Two (C40) separate acoustic echo cancellers

• 4-port (C60) / 2-port (C40) audio mixer

• Automatic gain control (AGC)

• Automatic noise reduction

• Active lip synchronization

AUDIO INPUTS (7 INPUTS (C60), 5 INPUTS (C40))

• Four microphones (C60) / two microphones (C40), 48 V phantom powered, XLR connector, each with separate echo cancellers and noise reduction; all microphones can be set for balanced line level

• Two RCA/Phono inputs, line level: Stereo PC input, configurable to two RCA/Phono inputs, line level: Mono auxiliary/DVD input

• One HDMI input, digital: stereo PC/DVD input

AUDIO OUTPUTS (3 OUTPUTS)

• Two RCA/Phono outputs, line level, stereo main audio, configurable to S/PDIF or two RCA/Phono outputs, line level, mono to recording device

• One HDMI output, digital, stereo main audio

DUAL STREAM

• H.239 (H.323) dual stream

• BFCP (SIP) dual stream

• Support for resolutions up to 1080p30/WUXGA

(C60) / WXGAp30 (C40), independent of main stream resolution

141

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface System settings

Administrator Guide

Setting passwords

MULTIPOINT SUPPORT

• Four-way embedded SIP/H.323 MultiPoint, reference

MultiSite

• Cisco TelePresence Multiway support (requires Cisco

TelePresence Video Communication Server [Cisco VCS] and Cisco TelePresence MCU)

• Ability to natively join multipoint conferences hosted on

Cisco Telepresence Multipoint Switch (CTMS)

MULTISITE FEATURES*

(embedeed multipoint)

• Four-way SIP/H.323 MultiSite. Resolution up to 720p30

(C60) / w576p30 (C40)

• Full individual audio and video transcoding

• Individual layouts in multisite continuous presence

(takes out selfview)

• H.323/SIP/VoIP in the same conference

• Support for Presentation (H.239/BFCP) from any participant at resolutions up to WXGAp30 (C60) /

WXGAp30 (C40)

• Best Impression (automatic continuous presence layouts)

• H.264, encryption, and dual stream from any site

• Dial in and dial out

• Additional telephone call (no license required)

• Conference rates up to 10 Mbps

PROTOCOLS

• H.323

• SIP

• ISDN (requires Cisco TelePresence ISDN Link)

EMBEDDED ENCRYPTION

• H.323/SIP point-to-point

• Standards-based: H.235 v3 and Advanced Encryption

Standard (AES)

• Automatic key generation and exchange

• Supported in Dual Stream

IP NETWORK FEATURES

• DNS lookup for service configuration

• Differentiated Services (QoS)

• IP adaptive bandwidth management (including flow control)

• Auto gatekeeper discovery

• Dynamic playout and lip-sync buffering

• H.245 DTMF tones in H.323

• Date and time support via NTP

• Packet loss based downspeeding

• URI Dialing

• TCP/IP

• DHCP

• 802.1x Network authentication

• 802.1Q Virtual LAN

• 802.1p QoS and class of service

• ClearPath

• Medianet: Mediatrace and Metadata

IPV6 NETWORK SUPPORT

• Single call stack support for both H323 and SIP

• Dual-stack IPv4 and IPv6 for DHCP, SSH, HTTP, HTTPS,

DNS, DiffServ

• Support for both static and autoconfiguration (stateless address autoconfiguration)

CISCO UNIFIED COMMUNICATIONS MANAgER

(requires Cisco UCM version 8.6 or later)

• Native registration with Cisco Unified Communications

Manager

• Basic Cisco Unified Communications Manager provisioning

• Firmware upgrade from Cisco Unified Communications

Manager

• Cisco Discovery Protocol and DHCP option 150 support

• Basic telephony features such as hold, resume, transfer, and corporate directory lookup

SECURITY FEATURES

• Management through HTTPS and SSH

• IP administration password

• Menu administration password

• Disable IP services

• Network settings protection

NETWORK INTERFACES

• One LAN/Ethernet (RJ-45) 10/100/1000 Mbit

• One LAN/Ethernet (RJ-45) interface to be used for the

Cisco TelePresence Touch for C-series user interface device only

OTHER INTERFACES

• USB host for future usage (C60 only)

• USB device for future usage

• GPIO – General purpose input/output (C60 only)

PRECISIONHD 1080P CAMERA

• 1/3” CMOS

• 12 × zoom (C60)

• 12 × zoom / 4 × zoom (C40)

• +15°/-25° tilt, +/- 90° pan

• 43.5° vertical field of view

• 72° horizontal field of view

• Focus distance 0.3 m–infinity

• 1920 × 1080 pixels progressive @ 60fps

(12 × zoom version)

• 1920 × 1080 pixels progressive @ 30fps

(4 × zoom version)

• Other formats supported (configurable through dipswitch):

- 1920 × 1080@60 Hz (HDMI only)***

- 1920 × 1080@50 Hz (HDMI only)***

- 1920 × 1080@30 Hz

- 1920 × 1080@25 Hz

- 1280 × 720@60 Hz***

- 1280 × 720@50 Hz ***

- 1280 × 720@30 Hz

- 1280 × 720@25 Hz

• Automatic or manual focus/brightness/white balance

• Far-end camera control

• Daisy-chain support (Visca protocol camera)***

• Dual HDMI and HD-SDI outputs

• Upside-down mounting with automatic flipping of picture

SYSTEM MANAgEMENT

• Support for the Cisco TelePresence Management Suite

(Cisco TMS)

• Total management through embedded SNMP, Telnet,

SSH, XML, SOAP

• Remote software upload through web server, SCP,

HTTP, HTTPS

• One RS-232 for local control and diagnostics

• Remote control and on-screen menu system

DIRECTORY SERVICES

• Support for local directories (My Contacts)

• Corporate directory

• Unlimited entries using server directory supporting

LDAP and H.350 (requires Cisco TMS)

• Unlimited number for corporate directory (through

Cisco TMS)

• Received calls with date and time

• Placed calls with date and time

• Missed calls with date and time

POWER

• Auto-sensing power supply

• 100-120/200-240 VAC, 60/50 Hz

• 175 watts max for codec and main camera

OPERATINg TEMPERATURE AND HUMIDITY

• 0° C to 35° C (32° F to 95° F) ambient temperature

• 10% to 90% relative humidity (RH)

STORAgE AND TRANSPORT TEMPERATURE

• -20° C to 60° C (-4° F to 140° F) at RH 10–90% (noncondensing)

DIMENSIONS

• Length: 17.4 in. / 44.2 cm

• Height: 1.7 in. / 4.4 cm

• Depth: 10.9 in. / 27.8 cm

• Weight: 8.8 lbs / 4 kg

* Requires option

** Multiwindow compositing not supported on the dual stream

*** Not supported on 4 x zoom camera

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface System settings

APPROVALS

EU/EEC

• Directive 2006/95/EC (Low Voltage Directive)

- Standard EN60950-1

• Directive 2004/108/EC (EMC Directive)

- Standard EN55022, Class A

- Standard EN55024

- Standard EN61000-3-2/-3-3

• Directive 2011/65/EU (RoHS)

Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

USA

• Approved according to UL60950-1

• Complies with FCC15B Class A

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Canada

• Approved according to CAN/CSA C22.2 No. 60950-1

• This Class A digital apparatus complies with Canadian

ICES-003

• Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada

MTBF PRODUCT RELIABILITY/MTBF

The predicted reliability is expressed in the expected random Mean Time Between Failures (MTBF) for the electronic components based on the Power On Hours:

Power On Hours (POH) > 69 000 hours

Useful Life Cycle > 6 years

ISO 9001 certificate is available upon request

Setting passwords

Administrator Guide

All specifications are subject to change without notice, system specifics may vary.

All images in these materials are for representational purposes only, actual products may differ.

Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco’s trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company.

June 2013

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface System settings

Profile 52”/55” using C60

UNIT DELIVERED COMPLETE WITH:

• Full HD LCD display, Codec C60, Touch 8 user interface device, remote control, PrecisionHD Camera (1080p), microphone (3x with single screen, 4x with dual screen), Digital Audio Module, integrated speakers and integrated cabling.

• Choice of installation configuration: floor stand, wheel base or wall mount on pedestal.

• Choice of screen size and configuration.

MONITOR available with:

• 52”/55’’ Full HD LCD, 16:9, 1080 × 1920 resolution

BASE available with:

• Floor standing foot plate

• Wheel base (not available on 52” Dual / 55” Dual)

• Wall mount on pedestal

BANDWIDTH

The same as Codec C60

FIREWALL TRAVERSAL

The same as Codec C60

VIDEO STANDARDS

The same as Codec C60

VIDEO FEATURES

The same as Codec C60

VIDEO INPUTS (5 INPUTS)

The same as Codec C60

VIDEO OUTPUTS (3 OUTPUTS)

The same as Codec C60

LIVE VIDEO RESOLUTIONS (ENCODE/DECODE)

The same as Codec C60

AUDIO STANDARDS

The same as Codec C60

AUDIO FEATURES

The same as Codec C60

AUDIO INPUTS (7 INPUTS)

The same as Codec C60

AUDIO OUTPUTS (3 OUTPUTS)

The same as Codec C60

DUAL STREAM

The same as Codec C60

MULTIPOINT SUPPORT

The same as Codec C60

MULTISITE FEATURES*

The same as Codec C60

PROTOCOLS

The same as Codec C60

EMBEDDED ENCRYPTION

The same as Codec C60

IP NETWORK FEATURES

The same as Codec C60

IPV6 NETWORK SUPPORT

The same as Codec C60

CISCO UNIFIED COMMUNICATIONS MANAgER

The same as Codec C60

SECURITY FEATURES

The same as Codec C60

NETWORK INTERFACES

The same as Codec C60

OTHER INTERFACES

The same as Codec C60

PRECISIONHD 1080P CAMERA

The same as Codec C60

SYSTEM MANAgEMENT

The same as Codec C60, as well as

• Cisco TelePresence Touch 8 user interface device

DIRECTORY SERVICES

The same as Codec C60

Setting passwords

Administrator Guide

POWER

Profile 52’’ / 52” Dual

• Auto-sensing power supply

• 100-120/200-240 VAC, 60/50 Hz, 6 A max

• 175 W max for codec and main camera

• Maximum power rating complete system,

526 W (52”) / 870 W (52” Dual)

Profile 55’’ / 55” Dual

• Auto-sensing power supply

• 100-120/200-240 VAC, 60/50 Hz,

4.5 A max (55”) / 8 A (55” Dual)

• 175 W max for codec and main camera

• Maximum power rating complete system,

350 W (55”) / 550 W (55” Dual)

• The display complies with ENERGY STAR requirements

OPERATINg TEMPERATURE AND HUMIDITY

• 0° C to 35° C (32° F to 95° F) ambient temperature

• 10% to 90% relative humidity (RH)

STORAgE AND TRANSPORT TEMPERATURE

• -20° C to 60° C (-4° F to 140° F) at RH 10–90% (noncondensing)

DIMENSIONS

Profile 52’’

• Height: 63.78 in. / 162 cm

• Width: 47.25 in. / 120 cm

• Depth: 6.7 in. / 17 cm (without footplate)

• Weight: 253.5 lbs / 115 kg (with floor standing footplate)

• 229.3 lbs / 104 kg (with wheel base)

Profile 52’’ Dual

• Height: 63.8 in. / 162 cm

• Width: 94.5 in. / 240 cm

• Depth: 6.7 in. / 17 cm (without footplate)

• Weight: 515.9 lbs / 234 kg (with floor standing footplate)

Profile 55’’

• Height: 64.6 in. / 164 cm

• Width: 49.6 in. / 126 cm

• Depth: 6.7 in. / 17 cm (without footplate)

• Weight: 245 lbs / 111 kg (with floor standing footplate)

• 225lbs / 102 kg (with wheel base)

Profile 55’’ Dual

• Height: 64.6 in. / 164 cm

• Width: 99.2 in. / 252 cm

• Depth: 6.7 in. / 17 cm (without footplate)

• Weight: 443 lbs / 201 kg (with floor standing footplate)

* Requires option

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface System settings

APPROVALS

EU/EEC

• Directive 2006/95/EC (Low Voltage Directive)

- Standard EN60950-1

• Directive 2004/108/EC (EMC Directive)

- Standard EN55022, Class A

- Standard EN55024

- Standard EN61000-3-2/-3-3

• Directive 2011/65/EU (RoHS)

Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

USA

• Approved according to UL60950-1

• Complies with FCC15B Class A

Canada

• Approved according to CAN/CSA C22.2 No. 60950-1

• This Class A digital apparatus complies with Canadian

ICES-003

• Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada

MTBF PRODUCT RELIABILITY/MTBF

The predicted reliability is expressed in the expected random Mean Time Between Failures (MTBF) for the electronic components based on the Power On Hours:

Power On Hours (POH) > 69 000 hours

Useful Life Cycle > 6 years

ISO 9001 certificate is available upon request

Setting passwords

Administrator Guide

All specifications are subject to change without notice, system specifics may vary.

All images in these materials are for representational purposes only, actual products may differ.

June 2013

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface System settings

Administrator Guide

Setting passwords

Profile 65” using C60

UNIT DELIVERED COMPLETE WITH:

• Full HD LCD display, Codec C60, Touch 8 user interface device, remote control, PrecisionHD 1080p Camera, microphones, Digital Audio Module, integrated speakers and integrated cabling.

MONITOR available with:

• 65’’ Full HD LCD, 16:9, 1080 × 1920 resolution

BASE available with:

• Floor standing footplate

• Wall mount on pedestal

BANDWIDTH

The same as Codec C60

FIREWALL TRAVERSAL

The same as Codec C60

VIDEO STANDARDS

The same as Codec C60

VIDEO FEATURES

The same as Codec C60

VIDEO INPUTS (5 INPUTS)

The same as Codec C60

VIDEO OUTPUTS (3 OUTPUTS)

The same as Codec C60

LIVE VIDEO RESOLUTIONS (ENCODE/DECODE)

The same as Codec C60

AUDIO STANDARDS

The same as Codec C60

AUDIO FEATURES

The same as Codec C60

AUDIO INPUTS (7 INPUTS)

The same as Codec C60

AUDIO OUTPUTS (3 OUTPUTS)

The same as Codec C60

DUAL STREAM

The same as Codec C60

MULTIPOINT SUPPORT

The same as Codec C60

MULTISITE FEATURES*

The same as Codec C60

PROTOCOLS

The same as Codec C60

EMBEDDED ENCRYPTION

The same as Codec C60

IP NETWORK FEATURES

The same as Codec C60

IPV6 NETWORK SUPPORT

The same as Codec C60

CISCO UNIFIED COMMUNICATIONS MANAgER

The same as Codec C60

SECURITY FEATURES

The same as Codec C60

NETWORK INTERFACES

The same as Codec C60

OTHER INTERFACES

The same as Codec C60

All specifications are subject to change without notice, system specifics may vary.

All images in these materials are for representational purposes only, actual products may differ.

Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries.

A listing of Cisco’s trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company.

June 2013

PRECISIONHD 1080P CAMERA

The same as Codec C60

SYSTEM MANAgEMENT

The same as Codec C60, as well as

• Cisco TelePresence Touch 8 user interface device

DIRECTORY SERVICES

The same as Codec C60

POWER

• Auto-sensing power supply

• 100-120/200-240 VAC, 60/50 Hz

• 175 W max for codec and main camera

• Maximum power rating complete system, 650 W

OPERATINg TEMPERATURE AND HUMIDITY

• 0° C to 35° C (32° F to 95° F) ambient temperature

• 10% to 90% relative humidity (RH)

STORAgE AND TRANSPORT TEMPERATURE

• -20° C to 60° C (-4° F to 140° F) at RH 10–90% (noncondensing)

DIMENSIONS

• Height: 65 in. / 165 cm

• Width: 59.1 in. / 150 cm

• Depth: 5.9 in. / 15 cm

• Weight: 330 lbs / 150 kg (with floor standing footplate)

APPROVALS

EU/EEC

• Directive 2006/95/EC (Low Voltage Directive)

- Standard EN 60950-1

• Directive 2004/108/EC (EMC Directive)

- Standard EN 55022, Class A

- Standard EN 55024

- Standard EN 61000-3-2/-3-3

• Directive 2011/65/EU (RoHS)

Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

USA

• Approved according to UL 60950-1

• Complies with FCC15B Class A

Canada

• Approved according to CAN/CSA C22.2 No. 60950-1

• This Class A digital apparatus complies with Canadian

ICES-003

• Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada

MTBF PRODUCT RELIABILITY/MTBF

The predicted reliability is expressed in the expected random Mean Time Between Failures (MTBF) for the electronic components based on the Power On Hours:

Power On Hours (POH) > 69 000 hours

Useful Life Cycle > 6 years

ISO 9001 certificate is available upon request

* Requires option

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface System settings

Profile 42”/52”/55” using C40

UNIT DELIVERED COMPLETE WITH:

• Full HD LCD display, Codec C40, Touch 8 user interface device, remote control, PrecisionHD Camera (1080p), microphones (2x), Digital Audio Module, integrated speakers and integrated cabling.

• Choice of installation configuration: floor stand, wheel base or wall mount on pedestal.

MONITOR available with:

• 42’’ Full HD LCD, 16:9, 1080 × 1920 resolution

• 52’’ Full HD LCD, 16:9, 1080 × 1920 resolution

• 55’’ Full HD LCD, 16:9, 1080 × 1920 resolution

BASE available with:

• Floor standing footplate

• Wheel base

• Wall mount on pedestal

BANDWIDTH

The same as Codec C40

FIREWALL TRAVERSAL

The same as Codec C40

VIDEO STANDARDS

The same as Codec C40

VIDEO FEATURES

The same as Codec C40

VIDEO INPUTS (4 INPUTS)

The same as Codec C40

VIDEO OUTPUTS (2 OUTPUTS)

The same as Codec C40

LIVE VIDEO RESOLUTIONS (ENCODE/DECODE)

The same as Codec C40

AUDIO STANDARDS

The same as Codec C40

AUDIO FEATURES

The same as Codec C40

AUDIO INPUTS (5 INPUTS)

The same as Codec C40

AUDIO OUTPUTS (3 OUTPUTS)

The same as Codec C40

DUAL STREAM

The same as Codec C40

MULTIPOINT SUPPORT

The same as Codec C40

MULTISITE FEATURES*

The same as Codec C40

PROTOCOLS

The same as Codec C40

EMBEDDED ENCRYPTION

The same as Codec C40

IP NETWORK FEATURES

The same as Codec C40

IPV6 NETWORK SUPPORT

The same as Codec C40

CISCO UNIFIED COMMUNICATIONS MANAgER

The same as Codec C40

SECURITY FEATURES

The same as Codec C40

NETWORK INTERFACES

The same as Codec C40

OTHER INTERFACES

The same as Codec C40

PRECISIONHD 1080P CAMERA

The same as Codec C40 with 12 × zoom camera

SYSTEM MANAgEMENT

The same as Codec C40, as well as

• Cisco TelePresence Touch 8 user interface device

DIRECTORY SERVICES

The same as Codec C40

Setting passwords

Administrator Guide

POWER

Profile 42’’

• Auto-sensing power supply

• 100-120/200-240 VAC, 60/50 Hz, 6 A max

• 175 W max for codec and main camera

• Maximum power rating complete system 365 W

Profile 52’’

• Auto-sensing power supply

• 100-120/200-240 VAC, 60/50 Hz, 6 A max

• 175 W max for codec and main camera

• Maximum power rating complete system 526 W

Profile 55’’

• Auto-sensing power supply

• 100-120/200-240 VAC, 60/50 Hz, 4.5 A max

• 175 W max for codec and main camera

• Maximum power rating complete system, 350 W

• The display complies with ENERGY STAR requirements

OPERATINg TEMPERATURE AND HUMIDITY

• 0° C to 35° C (32° F to 95° F) ambient temperature

• 10% to 90% relative humidity (RH)

STORAgE AND TRANSPORT TEMPERATURE

• -20° C to 60° C (-4° F to 140° F) at RH 10–90% (noncondensing)

DIMENSIONS

Profile 42’’

• Height: 63.78 in. / 162 cm

• Width: 38.58 in. / 98 cm

• Depth: 6.7 in. / 17 cm

• Weight: 220.5 lbs / 100 kg (with floor standing footplate)

• 200.6 lbs / 91 kg (with wheel base)

Profile 52’’

• Height: 63.78 in. / 162 cm

• Width: 47.25 in. / 120 cm

• Depth: 6.7 in. / 17 cm

• Weight: 253.5 lbs / 115 kg (with floor standing footplate)

• 229.3 lbs / 104 kg (with wheel base)

Profile 55’’

• Height: 64.6 in. / 164 cm

• Width: 49.6 in. / 126 cm

• Depth: 6.7 in. / 17 cm (without footplate)

• Weight: 245 lbs / 111 kg (with floor standing footplate)

• 225lbs / 102 kg (with wheel base)

* Requires option

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface System settings

APPROVALS

EU/EEC

• Directive 2006/95/EC (Low Voltage Directive)

- Standard EN60950-1

• Directive 2004/108/EC (EMC Directive)

- Standard EN55022, Class A

- Standard EN55024

- Standard EN61000-3-2/-3-3

• Directive 2011/65/EU (RoHS)

Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

USA

• Approved according to UL60950-1

• Complies with FCC15B Class A

Canada

• Approved according to CAN/CSA C22.2 No. 60950-1

• This Class A digital apparatus complies with Canadian

ICES-003

• Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada

MTBF PRODUCT RELIABILITY/MTBF

The predicted reliability is expressed in the expected random Mean Time Between Failures (MTBF) for the electronic components based on the Power On Hours:

Power On Hours (POH) > 69 000 hours

Useful Life Cycle > 6 years

ISO 9001 certificate is available upon request

Setting passwords

Administrator Guide

All specifications are subject to change without notice, system specifics may vary.

All images in these materials are for representational purposes only, actual products may differ.

June 2013

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

Supported RFCs

The RFC (Request for Comments) series contains technical and organizational documents about the Internet, including the technical specifications and policy documents produced by the Internet Engineering Task Force (IETF).

Current RFCs and drafts supported

• RFC 2190 RTP Payload Format for H.263 Video Streams

• RFC 2460 Internet protocol, version 6 (IPv6) specification

• RFC 2617 Digest Authentication

• RFC 2782 DNS RR for specifying the location of services

(DNS SRV)

• RFC 2976 The SIP INFO Method

• RFC 3016 RTP Payload Format for MPEG-4 Audio/Visual

Streams

• RFC 3261 SIP: Session Initiation Protocol

• RFC 3262 Reliability of Provisional Responses in SIP

• RFC 3263 Locating SIP Servers

• RFC 3264 An Offer/Answer Model with SDP

• RFC 3311 UPDATE method

• RFC 3361 DHCP Option for SIP Servers

• RFC 3388 Grouping of Media Lines in the Session

Description Protocol (SDP)

• RFC 3420 Internet Media Type message/sipfrag

• RFC 3515 Refer method

• RFC 3550 RTP: A Transport Protocol for Real-Time

Applications

• RFC 3551 RTP Profile for Audio and Video Conferences with Minimal Control

• RFC 3581 Symmetric Response Routing

• RFC 3605 RTCP attribute in SDP

• RFC 3711 The Secure Real-time Transport Protocol

(SRTP)

• RFC 3840 Indicating User Agent Capabilities in SIP

• RFC 3890 A Transport Independent Bandwidth Modifier for SDP

System settings

• RFC 3891 The SIP “Replaces” Header

• RFC 3892 Referred-By Mechanism

• RFC 3960 Early Media

• RFC 3986 Uniform Resource Identifier (URI): Generic

Syntax

• RFC 4028 Session Timers in SIP

• RFC 4091 The Alternative Network Address Types

(ANAT) Semantics for the Session Description Protocol

(SDP) Grouping Framework

• RFC 4092 Usage of the Session Description Protocol

(SDP) Alternative Network Address Types (ANAT)

Semantics in the Session Initiation Protocol (SIP)

• RFC 4145 TCP-Based Media Transport in the SDP

• RFC 4235 An INVITE-Initiated Dialog Event Package for the Session Initiation Protocol (SIP)

• RFC 4566 SDP: Session Description Protocol

• RFC 4568 SDP: Security Descriptions for Media Streams

• RFC 4574 The Session Description Protocol (SDP) Label

Attribute

• RFC 4582 The Binary Floor Control Protocol draft-ietf-bfcpbis-rfc4582bis-00 Revision of the Binary

Floor Control Protocol (BFCP) for use over an unreliable transport

• RFC 4583 Session Description Protocol (SDP) Format for

Binary Floor Control Protocol (BFCP) Streams draft-ietf-bfcpbis-rfc4583bis-00 Session Description

Protocol (SDP) Format for Binary Floor Control Protocol

(BFCP) Streams

• RFC 4585 Extended RTP Profile for RTCP-Based

Feedback

• RFC 4587 RTP Payload Format for H.261 Video Streams

D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.

149

Setting passwords

Administrator Guide

• RFC 4629 RTP Payload Format for ITU-T Rec. H.263

Video

• RFC 4733 RTP Payload for DTMF Digits, Telephony Tones and Telephony Signals

• RFC 4796 The SDP Content Attribute

• RFC 4862 IPv6 stateless address autoconfiguration

• RFC 5104 Codec Control Messages in the RTP Audio-

Visual Profile with Feedback (AVPF)

• RFC 5168 XML Schema for Media Control

• RFC 5245 Interactive Connectivity Establishment (ICE): A

Protocol for Network Address Translator (NAT) Traversal for Offer/Answer Protocols

• RFC 5389 Session Traversal Utilities for NAT (STUN)

• RFC 5577 RTP Payload Format for ITU-T

Recommendation G.722.1

• RFC 5589: SIP Call Control Transfer

• RFC 5626 Managing Client-Initiated Connections in the

Session Initiation Protocol (SIP)

• RFC 5766 Traversal Using Relays around NAT (TURN):

Relay Extensions to Session Traversal Utilities for NAT

(STUN)

• RFC 5768 Indicating Support for Interactive Connectivity

Establishment (ICE) in the Session Initiation Protocol (SIP)

• RFC 5905 Network Time Protocol Version 4: Protocol and

Algorithms Specification

• RFC 6156 Traversal Using Relays around NAT (TURN)

Extension for IPv6

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface

User documentation on the Cisco web site

In general, user documentation for the Cisco TelePresence products is available here:

► http://www.cisco.com/go/telepresence/docs

You have to choose your product category in the right pane until you find your product.

Follow one of these paths:

TelePresence Integration Solutions >

Cisco TelePresence Integrator C Series

Collaboration Room Endpoints >

Cisco TelePresence Profile Series

Alternatively, you can use the following short-links to find the documentation:

► http://www.cisco.com/go/cseries-docs

► http://www.cisco.com/go/profile-docs

System settings Setting passwords

Administrator Guide

The documents are organized in the following categories:

Installation guides:

Install and Upgrade > Install and Upgrade Guides

Getting started guide:

Install and Upgrade > Install and Upgrade Guides

Maintain and Operate > Maintain and Operate Guides

Administrator guides:

Maintain and Operate > Maintain and Operate Guides

User guides and Quick reference guides:

Maintain and Operate > End-User Guides

API reference guides:

Reference Guides | Command references

Knowledge base articles and frequently asked questions:

Troubleshoot and Alerts > Troubleshooting Guides

Physical interface guides:

Maintain and Operate | End-User Guides

CAD drawings:

Reference Guides > Technical References

TC Console user guide:

Configure > Configuration Guides

Video conferencing room guidelines:

Design > Design Guides

Software licensing information:

Software Downloads, Release and General Information > Licensing Information

Regulatory compliance and safety information:

Install and Upgrade > Install and Upgrade Guides

Software release notes:

Software Downloads, Release and General Information > Release Notes

150

Cisco TelePresence System Codec C40/C60 and Profiles using C40/60

Contents Introduction Web interface System settings

Intellectual property rights

THE SPECIFICATIONS AND INFORMATION REGARDING THE

PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE

WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND

RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE

ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF

ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL

RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE

ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION

PACKET THAT SHIPPED WITH THE PRODUCT AND ARE

INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE

TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,

CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California,

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL

DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE

PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-

NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED

OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND

NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING,

USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY

INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES,

INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR

DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO

USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/ or its affiliates in the U.S. and other countries. A listing of Cisco’s trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1005R)

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.

TANDBERG is now a part of Cisco. TANDBERG® is a registered trademark belonging to Tandberg ASA.

Setting passwords