AE3300
CARDIOID CONDENSER MICROPHONE
• Exacting detail, brilliant clarity and uncolored realism
• Superior anti-shock engineering ensures low handling noise
• Robust design for enduring dependability on the road
• Integral 80 Hz HPF switch and 10 dB pad
• Cardioid polar pattern reduces pickup of sounds from the sides and rear, improving isolation of desired sound source
The AE3300 is intended for use in professional applications where remote power is available. It requires 11V to 52V DC phantom power, which may be provided by a mixer or console, or by a separate, in-line source such as the Audio-Technica AT8801 singlechannel or CP8506 four-channel phantom power supplies.
Output from the microphone's XLRM-type connector is low impedance (Lo-Z) balanced. The signal appears across Pins 2 and
3; Pin 1 is ground (shield). Output phase is “Pin 2 hot” – positive acoustic pressure produces positive voltage at Pin 2.
AE3300 SPECIFICATIONS †
ELEMENT
POLAR PATTERN
FREQUENCY RESPONSE
LOW FREQUENCY ROLL-OFF
OPEN CIRCUIT SENSITIVITY
Fixed-charge back plate permanently polarized condenser
Cardioid
30-18,000 Hz
80 Hz, 12 dB/octave
–42 dB (7.9 mV) re 1V at 1 Pa*
IMPEDANCE 150 ohms
MAXIMUM INPUT SOUND LEVEL 147 dB SPL, 1 kHz at 1% T.H.D.;
157 dB SPL, with 10 dB pad (nominal)
NOISE 1 19 dB SPL
DYNAMIC RANGE (typical)
SIGNAL-TO-NOISE RATIO 1
PHANTOM POWER
REQUIREMENTS
SWITCHES
128 dB, 1 kHz at Max SPL
75 dB, 1 kHz at 1 Pa*
11-52V DC, 3 mA typical
WEIGHT (less accessories)
DIMENSIONS
OUTPUT CONNECTOR
ACCESSORIES FURNISHED
High-pass filter;
10 dB pad (nominal)
10.6 oz (300 g)
7.05" (179.0 mm) long, 1.97"
(50.0 mm) head diameter, 1.30" to 0.87" (33.0 mm to 22.0 mm) tapered body diameter
Integral 3-pin XLRM-type
AT8470 Quiet-Flex ™ stand clamp for 5 /
8
"-27 threaded stands; soft protective pouch
†In the interest of standards development, A.T.U.S. offers full details on its test methods to other industry professionals on request.
*1 Pascal = 10 dynes /cm 2 = 10 microbars = 94 dB SPL
1 Typical, A-weighted, using Audio Precision System One.
Specifications are subject to change without notice.
Polar Pattern
0
330 30
Frequency Response
300 60
10 dB
To avoid phase cancellation and poor sound, all mic cables must be wired consistently: Pin 1-to-Pin 1, etc.
270 90
When using the AE3300 in settings with a stage monitor speaker, the speaker should be located 180° off axis (at rear of the microphone). This placement, in conjunction with the microphone's unifor m cardioid pickup patter n, will vir tually eliminate the possibility of undesired audio feedback.
An integral 80 Hz hi-pass filter provides easy switching from a flat frequency response to a low-end roll-off. The roll-off position reduces the microphone's sensitivity to popping in close vocal use.
It also reduces the pickup of low-frequency ambient noise (such as traffic, air-handling systems, etc.), room reverberation and mechanically-coupled vibrations.
Avoid leaving the microphone in the open sun or in areas where temperatures exceed 110° F (43° C) for extended periods.
Extremely high humidity should also be avoided.
240
LEGEND
200 Hz
1 kHz
5 kHz
8 kHz
210 150
180
SCALE IS 5 DECIBELS PER DIVISION
120
LEGEND
50 100 200 500 1k
Frequency in Hertz
12" or more on axis
Roll-off
2k 5k 10k 20k
One-Year Limited Warranty
Audio-Technica brand products purchased in the U.S.A. are warranted for one year from date of purchase by Audio-Technica U.S., Inc. (A.T.U.S.) to be free of defects in materials and workmanship. In event of such defect, product will be repaired promptly without charge or, at our option, replaced with a new product of equal or superior value if delivered to A.T.U.S. or an Authorized Service Center, prepaid, together with the sales slip or other proof of purchase date. Prior approval from A.T.U.S. is required for return. This warranty excludes defects due to normal wear, abuse, shipping damage, or failure to use product in accordance with instructions. This warranty is void in the event of unauthorized repair or modification, or removal or defacing of the product labeling.
For return approval and shipping information, contact the Service Department,
Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224.
Except to the extent precluded by applicable state law, A.T.U.S. will have no liability for any consequential, incidental, or special damages; any warranty of merchantability or fitness for particular purpose expires when this warranty expires.
This warranty gives you specific legal rights, and you may have other rights which vary from state to state.
Outside the U.S.A., please contact your local dealer for warranty details.
Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224 www.audio-technica.com
P51449-EN ©2002 Audio-Technica U.S., Inc. Printed in Japan
