Kingston Technology HyperX 16GB DDR3L-1866

Kingston Technology HyperX 16GB DDR3L-1866
HX318LS11IBK2/16
16GB (8GB 1G x 64-Bit x 2 pcs.) DDR3L-1866
CL11 204-Pin SODIMM Kit
SPECIFICATIONS
CL(IDD)
11 cycles
Row Cycle Time (tRCmin)
44.7ns (min.)
Refresh to Active/Refresh
Command Time (tRFCmin)
260ns (min.)
Row Active Time (tRASmin)
34ns (min.)
Maximum Operating Power
TBD W* @1.35V
UL Rating
94 V - 0
Operating Temperature
0o C to 85o C
Storage Temperature
-55o C to +100o C
*Power will vary depending on the SDRAM used.
DESCRIPTION
FEATURES
HyperX HX318LS11IBK2/16 is a kit of two 1G x 64-bit (8GB)
DDR3L-1866 CL11 SDRAM (Synchronous DRAM) 2Rx8, low
•
JEDEC standard 1.35V (1.28V ~ 1.45V) and 1.5V (1.425V ~
1.575V) Power Supply
voltage, memory modules, based on sixteen 512M x 8-bit DDR3
FBGA components per module. Total kit capacity is 16GB.
•
VDDQ = 1.35V (1.28V ~ 1.45V) and 1.5V (1.425V ~ 1.575V)
•
933MHz fCK for 1866Mb/sec/pin
•
8 independent internal bank
•
Programmable CAS Latency: 13, 11, 10, 9, 8, 7, 6, 5
•
Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
•
8-bit pre-fetch
•
Burst Length: 8 (Interleave without any limit, sequential with
starting address “000” only), 4 with tCCD = 4 which does not
allow seamless read or write [either on the fly using A12 or
MRS]
•
Bi-directional Differential Data Strobe
•
Internal(self) calibration : Internal self calibration through ZQ
pin (RZQ : 240 ohm ± 1%)
•
On Die Termination using ODT pin
•
Average Refresh Period 7.8us at lower than TCASE 85°C,
3.9us at 85°C < TCASE < 95°C
•
Asynchronous Reset
•
PCB : Height 1.180” (30.00mm), double sided component
Each module kit has been tested to run at DDR3L-1866 at a
low latency timing of 11-11-11 at 1.35V or 1.5V. Additional
timing parameters are shown in the PnP Timing Parameters
section below. The JEDEC standard electrical and mechanical
specifications are as follows:
Note: The PnP feature offers a range of speed and timing options to support
the widest variety of processors and chipsets. Your maximum speed will
be determined by your BIOS.
PnP JEDEC TIMING PARAMETERS:
•
•
•
DDR3-1866 CL11-11-11 @1.35V or 1.5V
DDR3-1600 CL10-10-10 @1.35V or 1.5V
DDR3-1333 CL8-8-8 @1.35V or 1.5V
Continued >>
kingston.com/hyperx
Document No. 4807289-001.A00
03/19/15
Page 1
continued
HyperX
MODULE DIMENSIONS
FOR MORE INFORMATION, GO TO WWW.KINGSTON.COM/HYPERX
All Kingston products are tested to meet our published specifications. Some motherboards or system configurations may not operate at
the published HyperX memory speeds and timing settings. Kingston does not recommend that any user attempt to run their computers
faster than the published speed. Overclocking or modifying your system timing may result in damage to computer components.
kingston.com/hyperx
Document No. 4807289-001.A00
Page 2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement