Indesit | IDV 75 S | Datasheet | Indesit IDV 75 S tumble dryer

Instruction manual
TUMBLE DRYER
Contents
EN
English, 1
EN
Installation, 2-3
Where to install the tumble dryer
Ventilation
Electrical connections
Levelling the tumble dryer
Before you start your dryer
Description of the tumble dryer, 4
Front side
Rear side
Control panel
How to carry out a drying cycle, 5
Starting a drying programme
Drying settings, 6
Drying times
Drying programmes and options
IDV 75
IDV 75 S
Laundry, 7
Sorting laundry
Care labels
Special items
Warnings and suggestions, 8
General safety
Information on recycling and disposal
Saving energy and respecting the environment
Care and maintenance, 9
Disconnecting the power supply
Cleaning the filter after each cycle
Checking the drum after each cycle
Cleaning the tumble dryer
Troubleshooting, 10
This symbol reminds you to read this instruction
manual.
Assistance and Guarantee, 11-12-13
Spare parts
Keep this manual at hand for immediate reference
whenever necessary. Always store this manual close to the
tumble dryer and remember to pass it on to any new owners
when selling or transferring the appliance, so they may
familiarise with the warnings and suggestions herein
contained.
Read these instructions carefully: the following pages
contain important information on installation and useful
suggestions for operating the appliance.
1
Installation
• Install the dryer far from gas
ranges, stoves, radiators or
hobs, as flames may damage it.
If the dryer is installed below a
worktop, ensure there are 10
mm between the upper panel of
the dryer and any objects above
it, and 15 mm between the sides
15 mm
15 mm
of the machine and the walls or
furniture units adjacent to it. This
ensures adequate air circulation. Make sure the air inlets on
the rear panel are not blocked or obstructed.
• You should also make sure that the room in which the
tumble dryer is installed is not damp, and that it is
adequately ventilated.
• We do not recommend that the dryer is installed in a
cupboard but the dryer must never be installed behind a
lockable door, a sliding door or a door with a hinge on the
opposite side to that of the dryer door.
10 mm
EN
Where to install the tumble dryer
Ventilation
This appliance gently dries laundry by taking in cold, clean and
relatively dry air, heating it and passing it through the fabric.
To facilitate the drying process, damp air is expelled at the
rear, through a ventilation hose. When the dryer is in use, there
has to be adequate ventilation to avoid a back flow of gases
into the room from appliances burning other fuels, including
open fires.
Mobile ventilation system
When using the tumble dryer with the mobile ventilation
system, a ventilation hose must be connected. The hose
should be securely fastened to the ventilation hole at the rear of
the appliance (see “Description of the tumble dryer”). We
recommend the hose is connected to an outlet near the tumble
dryer, if possible. If it cannot be installed in a permanent spot,
the tumble dryer will still function perfectly well if the ventilation
hose is passed through a partially-opened window.
Make sure you do not point the ventilation hose towards the
air inlet, which is located on the rear of the appliance.
The ventilation hose should not exceed a maximum length of
2.4 metres; it should also be shaken frequently to remove any
fluff, dust or water deposits inside it. Make sure you do not
crush the hose.
Fixed ventilation system
We recommend the ventilation hose is connected to a
ventilation system for windows or doors, available from the
retailer which originally sold you the appliance or from your
local spare parts stockist.
2
Wall ventilation hole
1. Leave an opening in the wall
to the left of the tumble dryer
installation site.
2. Make the hose as short and
straight as possible, in order to
prevent any moisture from
condensing and leaking back
into the appliance.
A 3. The hole in the wall must
also be straight and pointing
downwards, so that the flow of air coming out is not
impeded.
Areas A and B should be checked frequently, to prevent the
accumulation of fluff or debris, particularly if the tumble dryer
is used very often. The hose adaptor must be fitted
correctly, in order to prevent damp air from coming back
into the room.
B
Window ventilation hole
The ventilation hole should be
directly behind the dryer in
order to keep the hose as short
as possible.
Make sure you do not push
the tumble dryer too far
backwards, as this could lead
to the ventilation hose being
crushed, bent or even
disconnected.
There should be no cuts, kinks or “U”-shaped bends in the
hose, as these could impede ventilation or trap
condensation.
Ventilation through an open window
The end of the hose must be
facing downwards, in order to
prevent the hot, damp air from
forming condensation in the
room or the tumble dryer.
Make sure that the tumble dryer is adequately ventilated,
and that the end of the ventilation hose is not pointing
towards the air inlet pipe on the rear of the appliance.
The ventilation hose must always be fitted to ensure
optimum performance.
Make sure that the ventilation hose and the air inlet vents
are not obstructed or blocked.
Do not let the tumble dryer recirculate exhaust air.
Improper use of the tumble dryer may result in fire hazards.
The air emitted by the tumble dryer must not be expelled in
the same duct as used for the fumes produced by different
appliances which burn gas or other fuels.
Do not discharge the exhaust air into an extraction system
or any duct with an extractor fan. This will affect the way the
thermal controls operate and can result in a fire hazard.
Electrical connections
Levelling the tumble dryer
Before plugging the appliance into the socket, check the following:
• Make sure your hands are dry.
• The socket must have an earth connection.
• The socket must be able to withstand the machine’s
maximum power output as indicated on the data plate (see
Description of the tumble dryer).
• The power supply voltage must fall within the values indicated
on the data plate (see Description of the tumble dryer).
• The socket must be compatible with the dryer’s plug.
Should this not be the case, replace the plug or the socket.
Do not use extension cords.
The dryer must not be installed outdoors, even if the space is
sheltered. It can be very dangerous if exposed to rain or storms.
Once installed, the dryer’s electrical wire and plug must
be within reach.
The power cord must not be bent or squashed.
The power cord is supplied fitted with a BS1363 plug
and with a 13 amp BS1362 fuse. If it is necessary to fit a
replacement fuse, it must be a 13 Amp ASTA approved
to BS1362 type. WARNING: The plug must not be used
without a fuse cover. If a replacement fuse holder/cover is
required, it must be of the same colour coding or wording as
shown on the base of the plug.
Replacements are available from authorised dealers.
The tumble dryer should be installed level in order to
operate correctly.
EN
After installing the tumble
dryer in its permanent
position, make sure it is
level; check its side-to-side
levelling first, followed by
front-to-back.
If the tumble dryer is not
perfectly level, use a wooden
block to support it while you
adjust the two front feet, up
or down as necessary.
Moulded plug
Before you start your dryer
Once the tumble dryer is installed, clean the inside of the
drum before operating it and remove any dirt accumulated
during transportation.
Changing the plug
The wires in the power cord are coloured in accordance
with the following.
Green and Yellow (Earth)
wire to terminal marked
“E”, symbol x, or coloured
green and yellow.
13A ASTA approved fuse
to BS 1362.
GREEN &
YELLOW
BROWN
Blue (Neutral) wire to
terminal marked ”N” or
coloured black.
BLUE
13 ampere fuse
CROSS-BAR
CORD GRIP
Brown (live) wire to teminal
marked “L” or coloured
red.
If the plug being replaced is a non-rewirable type, then the
cut-off plug must be disposed of safely. DO NOT leave it where
it can be inserted into a socket and create a shock hazard.
The power cord should be checked periodically and replaced
by a cord specially prepared for this dryer and fitted only by
authorized technicians (see Service). New or longer power
cords are supplied at an extra charge by authorized dealers.
The manufacturer denies any responsibility should any
of these rules not be followed.
If in doubt about any of the above consult a qualified electrician.
3
Description of the tumble dryer
Front side
Rear side
EN
Control panel
Serial number
and model
number
Drum
Filter
Rating Plate
Air inlet
Caution, high
temperature
Connection for
ventilation hose
Control panel
High Heat
button
Start
button
Drying time
selector knob
Drying time selector knob
This is used to set the drying time: turn the knob in a clockwise direction until the indicator is set to the desired drying time (see
Drying settings). Do not attempt to turn the knob anticlockwise.
High Heat button
It can be used to customise the selected programme in accordance with your own requirements.
START button
Press the button to begin drying.
4
How to carry out a
drying cycle
Starting a drying programme
EN
1. Plug the dryer into the power supply socket.
2. Select a suitable drying programme for the type of laundry (see Laundry).
3. Open the door, ensure that the filter is clean and securely placed.
4. Load the machine, making sure that no piece of laundry gets between the door and the door seal. Close the door.
5. Turn the “Drying time selector” knob until the indicator is pointing towards the most suitable drying time for the type of fabric in
that load. Use the table to check the relationship between fabric type and load capacity (see Drying settings), and make sure you
are familiar with the instructions provided for each type of fabric (see Laundry). Do not attempt to turn the knob anticlockwise.
6. If necessary, set the temperature using the HIGH HEAT button.
7. Press the START button to start the drying cycle.
Laundry can be checked while the drying programme runs and any garments already dry can be removed, while drying continues
for the remaining items. After closing the door, press the START button to resume machine operation.
8. The final COLD DRYING phase (i.e. the fabrics are cooled) activates during the last few minutes of the drying programme; always
allow this phase to terminate.
9. Open the door, remove the laundry then clean the filter and replace it.
10. Disconnect the dryer from the power supply.
5
Drying settings
Drying times
EN
The drying time depends on the size of the load and on the type of fabric it contains (see Table).
The cold drying cycle runs during the final 10 minutes of the programme.
For large loads, select the High Heat option if available.
Fabric
Cotton –
high heat
Synthetics –
high heat
Acrylics –
low heat
Load
1 kg
20 - 30
minutes
20 - 30
minutes
25 - 40
minutes
2 kg
35 - 45
minutes
35 - 45
minutes
40 - 60
minutes
3 kg
45 - 60
minutes
45 - 60
minutes
4 kg
60 - 70
minutes
5 kg
70 - 80
minutes
6 kg
80 - 100
minutes
7 kg
90 - 120
minutes
-
-
-
-
-
-
-
-
-
Drying times are approximate and may vary depending on the following:
•
•
•
•
Amount of water retained by items after the spin cycle: towels and delicate items retain a lot of water.
Fabrics: items of the same fabric, but with different texture and thickness may have different drying times.
Amount of laundry: single items and small loads will take a short time to dry.
Drying: if items are to be ironed, they can be removed from the dryer while still slightly damp. Items that require complete drying
can be left longer.
• Temperature of the room: the lower the temperature of the room, the longer it will take for the dryer to dry clothing.
• Bulk: certain bulky items require special care during the drying process. We suggest removing these items and replacing them in
the dryer once they have been shaken out: repeat this procedure several times during the course of the drying cycle.
Do not over-dry items.
All fabrics contain natural dampness which helps to keep them soft and fluffy.
Drying programmes and options
Refresh
A short programme suitable for refreshing fibres and garments through the emission of cool air. It lasts about 10 minutes.
As this is not a drying programme, it is not to be used for garments that are still wet.
High Heat button
The high heat button selects the drying temperature. When the button is out low heat is selected and when it is pushed in high heat
is selected
6
Laundry
Sorting laundry
Care labels
• Check the symbols on the care labels of the various
garments to verify whether the garments can be safely
tumble dried.
• Sort laundry according to the type of fabric.
• Empty all pockets and check for loose buttons.
• Close zips and hooks and fasten belts and strings without
tightening them.
• Wring out garments to remove the maximum amount of
water possible.
Always check the care labels, especially when placing
garments in the tumble dryer for the first time. Below are the
most commonly used symbols:
Do not load the dryer when garments are dripping wet.
Items not suitable for tumble drying:
• Items containing rubber parts or similar materials, or
plastic film covering (pillows, cushions or PVC sports
jackets), any type of inflammable object or objects
containing inflammable substances (used towels
containing hairspray).
• Glass fibres (certain types of draperies).
• Items which have been previously dry cleaned.
• Items marked with the ITLC symbol (“Special garments”)
, which may be washed using special household
products. Follow instructions carefully.
• Large bulky items (duvets, sleeping bags, pillows,
cushions, etc.) that expand when dried and hamper air
circulation inside the tumble dryer.
Maximum load sizes
Do not overload the drum.
The following values indicate the weight of dry garments:
Natural fibres: maximum 7 kg
Synthetic fibres: maximum 3 kg
Do not overload the dryer as this may result is reduced
drying performance.
Typical weights
Note: 1 kg = 1000 g
Garments
Blouse
Cotton
Other
Dress
Cotton
Other
150
100
500
350
700 g
Jeans
1,000 g
10 Nappie
Shirt
g
g
g
g
300 g
200 g
Cotton
Other
T-shirt
125 g
May be tumble dried.
Do not tumble dry.
Tumble dry – high heat.
Tumble dry – low heat.
Special items
Blankets and bedcovers: acrylic items (Acilian, Courtelle,
Orion, Dralon) must be dried with great care at low heat.
Avoid drying for long periods.
Creased or pleated garments: read the drying instructions
supplied by the manufacturer.
Starched garments: do not dry together with nonstarched items. Remove the maximum amount of starch
solution possible before placing these items in the dryer. Do
not over-dry: starch turns powdery leaving garments limp –
this defeats its purpose.
Household linen
Duvet cover
(double bed)
Cotton
Other
1,500 g
1,000 g
Large tablecloth
700 g
Small tablecloth
250 g
Tea cloth
100 g
Bath towel
700 g
Hand towel
350 g
Double bed
sheet
500 g
350 g
Single bed sheet
When mixing synthetic fibres with cotton garments, the
latter may still be damp at the end of the drying cycle. If this
happens, simply put them through a short drying cycle.
Note: when setting the duration of the drying cycle,
remember that the cold drying phase runs during the last 10
minutes, during which the dryer does not dry the garments.
7
EN
Warnings
and suggestions
This appliance was designed and manufactured in
EN
compliance with current international safety standards. The
following information is provided for safety reasons and
must be read carefully.
General safety
• The final part of a tumble dryer cycle occurs without heat
(cooling cycle) to ensure that the laundry is not damaged
due to excessive temperatures.
• This tumble dryer must not be used by persons (including
children) with physical, sensory or mental impairments or
with little experience and knowledge of the appliance,
unless they are supervised or have been adequately
instructed on its use by the person responsible for their
safety.
• This tumble dryer is designed for domestic and nonprofessional use.
• Do not touch the appliance while barefoot or with wet
hands or feet.
• Unplug the appliance by pulling on the plug, not the cord.
• Do not allow children near the appliance while it is in use.
After use, switch the appliance off and unplug it. Keep the
appliance door closed to prevent children using it as a
toy.
• Children must be supervised to ensure that they do not
play with the appliance.
• The appliance must be correctly installed and receive
adequate ventilation. The air inlet vents on the back of the
dryer must never be obstructed (see Installation).
• Never direct the vent hose towards the air inlet vents on
the back of the dryer.
• Never use the dryer on carpeting with high pile as this
may prevent air from entering the dryer from the base.
• Check whether the dryer is empty before loading it.
•
The rear part of the dryer may become very hot:
do not touch it while the appliance is in use.
• Do not use the dryer unless the filter is properly
positioned (see Care and Maintenance).
• Do not use liquid fabric softener in the dryer; add it to the
final rinse of the wash cycle.
• Do not overload the dryer (see Laundry for the maximum
load sizes).
• Do not add items that are dripping wet.
• Tumble dry items only if they have been washed with
water and detergent, and have been rinsed and put
through a spin cycle. Drying items that have NOT been
washed with water may cause the risk of fire.
• Always read the instructions on the care label carefully
(see Laundry).
• Do not tumble dry items that have been treated with
chemical products.
• Never tumble dry items that are contaminated with
inflammable substances (cooking oil, acetone, alcohol,
petrol, kerosene, stain removers, turpentine, waxes, wax
removers and hairspray), unless they have been washed
in hot water with an extra amount of detergent.
• Do not tumble dry rubber, rubber-backed articles and
garments, cushions with foam rubber padding, latex
foam, rubber, plastic, shower caps, water-resistant
fabrics, nappy pants or liners, polyethylene and paper.
• Remove all objects from pockets, particularly lighters
(risk of explosion).
8
• Do not tumble dry large, excessively bulky items.
• Do not tumble dry acrylic fibres at high temperatures.
• Complete each programme with the relative cold drying
phase.
• Do not switch the tumble dryer off if items that are still
warm are inside it.
• Clean the filter after each use (see Care and maintenance).
• Do not allow lint to build up around the tumble dryer.
• Never climb on the top of the dryer as this may damage
the appliance.
• Always comply with electrical regulations and
requirements (see Installation).
• Always purchase original accessories and spare parts
(see Assistance).
WARNING: Never stop the dryer before the end of the
drying cycle unless all items have been quickly removed and
hung in order to dispel heat.
Information on recycling
and disposal
As part of our continual commitment towards environmental
protection, we reserve the right to use recycled quality
components to reduce costs for our customers and to
minimise materials wastage.
• Disposing of the packaging materials: follow local
regulations to allow for recycling of packaging materials.
• In order to minimise the risk of injury to children, remove
the door and plug, then cut the power supply cord flush
with the appliance. Dispose of these parts separately to
prevent the appliance from being connected to a power
supply socket.
Disposal of old household appliances
European Directive 2002/96/EC concerning Waste
Electrical and Electronic Equipment (WEEE) states
that household appliances should not be disposed of
with normal household waste. Old appliances should
be collected separately in order to optimise the cost of reusing and recycling materials comprising the machine, while
preventing potential damage to public health and the
environment. The crossed-out wheeled bin symbol appears
on all products to remind owners of the obligations
regarding separate waste collection.
Owners should contact their local authorities or appliance
dealers for further information concerning the correct
disposal of household appliances.
Saving energy and respecting the
environment
• Wring out items before tumble drying them to remove
the maximum amount of water possible (if they are
previously washed in a washing machine, select a spin
cycle). This ensures that energy is saved during tumble
drying.
• Always use the tumble dryer at full load to save energy:
single items and small loads may take longer to dry.
• Clean the filter at the end of each cycle to reduce energy
consumption costs (see Care and maintenance).
Care and maintenance
Disconnecting the power supply
Disconnect the dryer when not in use or during cleaning
and maintenance operations.
EN
Cleaning the filter after each cycle
The filter is a fundamental component of the dryer: its
function is to collect lint and fluff that form during drying.
Clean the filter once drying is completed, by rinsing it under
running water or cleaning it with a vacuum cleaner. Should the
filter become clogged, the flow of air inside the dryer will be
seriously hampered: drying times becomes longer and more
energy is consumed. Moreover, the dryer may become
damaged.
The filter is located behind of
the dryer seal (see Picture).
Removing the filter:
1. Pull the filter’s plastic handle
upwards (see Picture).
2. Clean the fluff off the filter and
replace it correctly. Ensure that
the filter is pushed fully home.
Do not use the dryer unless the filter has been replaced in
its holder.
Checking the drum after each cycle
Rotate the drum manually to remove smaller items
(handkerchiefs) that could have been left inside the dryer.
Cleaning the drum
Avoid using abrasives, steel wool or stainless steel
cleaning agents to clean the drum.
A coloured film may appear on the stainless steel drum
surface: it may be caused by a combination of water and/or
cleaning agents such as wash-softeners. This coloured film
does not affect the dryer’s performance.
Cleaning the tumble dryer
• The external metal and plastic parts and the rubber parts
can be cleaned with the aid of a damp cloth.
• Periodically check the vent hose and all other parts of the
venting system and remove any accumulations of fluff and
lint.
Do not use solvents or abrasives.
Have the dryer checked regularly by authorised technical
personnel in order to ensure that the electrical and
mechanical parts work safely (see Assistance).
9
Troubleshooting
EN
If you feel that the dryer is not working properly, consult the following troubleshooting suggestions before contacting the Technical
Assistance Centre (see Assistance).
Problem:
Possible causes / Solutions:
The dryer does not start.
•
•
•
•
•
•
•
The plug has not been inserted far enough into the socket to make contact.
There has been a power cut.
The fuse has blown. Try connecting another appliance to the same socket.
If an extension cord is used, try connecting the dryer plug directly into the socket.
The door has not been closed properly.
The programme has not been set correctly (see How to carry out a drying cycle).
The START button has not been pressed (see How to carry out a drying cycle).
Drying times are too long.
•
•
•
•
•
•
•
The filter has not been cleaned (see Care and maintenance).
An incorrect drying time was selected for the type of load (see Laundry).
The items are too wet (see Laundry).
The dryer is overloaded (see Laundry).
The flexible ventilation hose may be blocked (see Installation).
The air inlet may be blocked or obstructed (see Installation).
The fixed ventilation flap, on the protective weatherproof cover, may be obstructed
(see Installation).
The dryer is noisy during the first
few minutes of operation.
• This is normal, especially if the dryer has not been used for a long time. If the noise
persists during the entire cycle, contact the Technical Assistance Centre.
10
Assistance
Before contacting the Technical Assistance
Centre:
• Follow the troubleshooting guide to check whether
problems can be solved personally (see Troubleshooting).
• If not, switch the dryer off and contact the Technical
Assistance Centre closest to you.
Provide the following data when contacting the
Technical Assistance Centre:
Spare parts
This dryer is a complex machine. Attempting to repair it
personally or employing an unqualified service agent may
put the safety of people at risk, damage the machine or
invalidate the spare parts guarantee.
Always contact a qualified technician when experiencing
problems with this machine. The spare parts were
designed exclusively for this machine and should not be
used for any other purpose.
• name, address and postal code
• telephone number
• type of malfunction
• date of purchase
• the appliance model (Mod.)
• the dryer’s serial number (S/N)
This information can be found on the data plate located
behind the door.
This appliance conforms to the following EEC directives:
- 2006/95/EC (Low Voltage Directive)
- 89/336/EEC, 92/31/EEC, 93/68/EEC (Electromagnetic Compatibility Directive).
11
EN
Guarantee
12 Months Parts and Labour Guarantee
EN
Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown repairs for twelve
months from the date of purchase.
This gives you the reassurance that if, within that time, your appliance is proven to be defective because of either
workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to you.
This guarantee is subject to the following conditions:
-
The appliance has been installed and operated correctly and in accordance with our operating and
maintenance instructions.
The appliance is used only on the electricity or gas supply printed on the rating plate.
The appliance has been used for normal domestic purposes only.
The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by any
person not authorised by us.
Any repair work must be undertaken by us or our appointed agent.
Any parts removed during repair work or any appliance that is replaced become our property.
The appliance is used in the United Kingdom or Republic of Ireland.
-
The guarantee does not cover:
-
Damage resulting from transportation, improper use, neglect or interference or as a result of improper
installation.
Replacement of any consumable item or accessory. These include but are not limited to:
plugs, cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.
Replacement of any removable parts made of glass or plastic.
-
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR
NON-DOMESTIC PREMISES.
5 Year Parts Guarantee
Indesit also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you registering your
appliance with us and the parts being fitted by one of our authorised engineers. There will be a charge for our engineer's
time. To activate the extra parts warranty on your appliance, simply call our registration line on 08448 24 24 24
(Republic of Ireland 01 230 0800)
Extended Guarantees
We offer a selection of repair protection plans that enable you to fully cover yourself against the expense of repair bills for
the life of your policy. To find the ideal plan for you please call our advice line on
08448 226 226 (Republic of Ireland 01 230 0233).
Free Helpdesk Service
We have a dedicated team who can provide free advice and assistance with your appliance if you experience any
technical difficulties within the first 90 days of ownership. Simply call our Indesit Service Hotline on 08448 224 224
(Republic of Ireland 0818 313 413)for telephone assistance, or, where necessary, to arrange for an engineer to call.
12
After Sales Service
No one is better placed to care for your Indesit appliance during the course of its working life than us - the manufacturer.
Essential Contact Information
Indesit Service
We are the largest service team in the UK and Ireland offering you access to 400 skilled telephone advisors and 1100 fully
qualified engineers on call to ensure you receive fast, reliable, local service.
UK: 08448 224 224
Republic of Ireland: 0818 313 413
www.indesitservice.co.uk
Please note: Our advisors will require the following information:
Model number:
Serial number:
Parts and Accessories
We supply a full range of genuine replacement parts as well as accessory products that protect and hygienically clean
your appliance to keep it looking good and functioning efficiently throughout its life.
UK: 08448 225 225
Republic of Ireland: 0818 313 413
www.indesitservice.co.uk
Appliance Registration
We want to give you additional benefits of Indesit ownership. To activate your free 5 year parts guarantee you must
register your appliance with us.
UK: 08448 24 24
Republic of Ireland: 01 230 0800
www.indesitservice.co.uk
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB
Indesit Company Unit 49 Airways Industrial Estate, Dublin 17
Recycling & Disposal Information
As part of Indesit's continued commitment to helping the environment, Indesit reserves the right to use quality, recycled
components to keep down customer costs and minimise material wastage.
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children, remove the door, plug
and cut the mains cable off flush with the appliance. Dispose of these parts separately to ensure that the appliance can
no longer be plugged into a mains socket, and the door cannot be locked shut.
13
EN
EN
14
EN
15
195089406.00
11/2010
EN
16
Download PDF

advertising