Instruction Manual - Service après vente - Dewalt

Instruction Manual - Service après vente - Dewalt
INSTRUCTION MANUAL
DCD710-XE
10 mm 10.8 V CORDLESS ADJUSTABLE CLUTCH DRILL/DRIVER
LPA
KPA
LWA
KWA
Definitions: Safety Guidelines
The definitions below describe the level of severity for each signal
word. Please read the manual and pay attention to these symbols.
DANGER: Indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.
NOTICE: Indicates a practice not related to personal injury which, if
not avoided, may result in property damage.
Vibration emission value ah
ah =
Uncertainty K =
DCD710-XE
10.8
Li-Ion
min-1
min-1
Nm
W
mm
0–400
0–1500
24/15
180
10
mm
mm
kg
20
10
0.91
65
3
76
3
m/sВІ
m/sВІ
< 2.5
1.5
The vibration emission level given in this information sheet has been measured in
accordance with a standardised test given in EN 60745 and may be used to compare
one tool with another. It may be used for a preliminary assessment of exposure.
WARNING: The declared vibration emission level represents the main applications
of the tool. However if the tool is used for different applications, with different
accessories or poorly maintained, the vibration emission may differ. This may
significantly increase the exposure level over the total working period.
Technical Data
VDC
dB(A)
dB(A)
dB(A)
dB(A)
Vibration total values (triax vector sum) determined according to EN 60745:
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL,
CALL US AT: 1800 338 002 (Aust) or 0800 339 258 (NZ).
Voltage
Battery type
No-load speed:
1st gear
2nd gear
Max torque (hard/soft)
Power output (MWO)
Chuck capacity
Maximum drilling capacity
Wood
Metal
Weight (without battery pack)
(sound pressure)
(sound pressure uncertainty)
(sound power)
(sound power uncertainty)
An estimation of the level of exposure to vibration should also take into account
the times when the tool is switched off or when it is running but not actually doing
the job. This may significantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator from the effects of
vibration such as: maintain the tool and the accessories, keep the hands warm,
organisation of work patterns.
SAFETY INSTRUCTIONS FOR POWER TOOLS
When using power tools, always observe the safety regulations applicable in your
country to reduce the risk of fire, electric shock and personal injury. Read the following
safety instructions before attempting to operate this product. Keep these instructions in
a safe place.
WARNING: To reduce the risk of injury, read the instruction manual.
1
GENERAL POWER TOOL SAFETY WARNINGS
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective
equipment such as dust mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off position
before connecting to power source and/or battery pack, picking up or
carrying the tool. Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of the power tool may result in
personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of dust
collection can reduce dust-related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the rate
for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and must
be repaired.
c) Disconnect the plug from the power source and/or the battery pack from
the power tool before making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
WARNING! Read all safety warnings and all instructions Failure to follow
the warnings and instructions may result in electric shock, fire and/or serious
injury.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR
FUTURE REFERENCE
The term “power tool” in the warnings refers to your mains-operated (corded) power
tool or battery-operated (cordless) power tool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords increase the risk of electric
shock.
e) When operating a power tool outdoors, use an extension cord suitable
for outdoor use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual
current device (RCD) protected supply. Use of an RCD reduces the risk of
electric shock.
2
d) Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits, etc. in accordance with
these instructions, taking into account the working conditions and the work
to be performed. Use of the power tool for operations different from those
intended could result in a hazardous situation.
5) BATTERY TOOL USE AND CARE
a) Recharge only with the charger specified by the manufacturer. A charger
that is suitable for one type of battery pack may create a risk of fire when
used with another battery pack.
b) Use power tools only with specifically designated battery packs. Use of any
other battery packs may create a risk of injury and fire.
c) When battery pack is not in use, keep it away from other metal objects like
paper clips, coins, keys, nails, screws, or other small metal objects that
can make a connection from one terminal to another. Shorting the battery
terminals together may cause burns or a fire.
d) Under abusive conditions, liquid may be ejected from the battery; avoid
contact. If contact accidentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected from the battery may
cause irritation or burns.
6) SERVICE
a) Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power tool
is maintained.
range can cause loss of power and can result in overheating. All DEWALT tools are
factory tested; if this tool does not operate, check the power supply. Your DEWALT
tool is double insulated, therefore no earth wire is required.
• Young children and the infirm. This appliance is not intended for use by young
children or infirm persons without supervision.
– This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
– Children should be supervised to ensure that they do not play with the appliance.
• Replacement of the supply cord. If the supply cord or plug is damaged, it must
be replaced by the manufacturer or an authorised DEWALT Service Centre in
order to avoid a hazard.
Extension Cords
CAUTION: Use only extension cords that are approved by the country’s Electrical
Authority. Before using extension cords, inspect them for loose or exposed wires,
damaged insulation and defective fittings. Replace the cord if necessary.
ADDITIONAL SPECIFIC SAFETY RULES
• Wear ear protectors when impact drilling. Exposure to noise can cause hearing
loss.
• Use auxiliary handle(s) if supplied with the tool. Loss of control can cause
personal injury.
• Hold power tools by insulated gripping surfaces when performing an
operation where the cutting accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a “live” wire will make exposed metal parts of
the power tool “live” and could give the operator an electric shock.
• Use clamps or another practical way to secure and support the workpiece
to a stable platform. Holding the work by hand or against your body leaves it
unstable and may lead to loss of control.
• Air vents often cover moving parts and should be avoided. Loose clothes,
jewellery or long hair can be caught in moving parts.
WARNING: We recommend the use of a residual current device with a residual
current rating of 30mA or less.
Electrical Safety
The electric motor has been designed for one voltage range only. Always check that
the power supply corresponds to the voltage on the rating plate. 220–240 V AC
means your tool will operate on alternating current. Operation at a voltage outside this
3
min ..................minutes
or DC.....direct current
...................Class I Construction
........................(grounded)
...................Class II Construction
........................(double insulated)
…/min .............per minute
BPM .................beats per minute
RPM.................revolutions per minute
sfpm ................surface feet per minute
WARNING: ALWAYS wear approved protective safety equipment complying with
the following standards:
• Eye protection: AS/NZS1337 Eye Protectors for Industrial Applications;
• Hearing protection: AS/NZS1270 Acoustics – Hearing Protection;
• Respiratory protection: AS/NZS1716 Respiratory Protective Devices.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to cause cancer, birth defects
or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of
work. To reduce your exposure to these chemicals: work in a well ventilated area, and
work with approved safety equipment, such as those dust masks that are specially
designed to filter out microscopic particles.
• Avoid prolonged contact with dust from power sanding, sawing, grinding,
drilling, and other construction activities. Wear protective clothing and wash
exposed areas with soap and water. Allowing dust to get into your mouth, eyes,
or lay on the skin may promote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disburse dust, which may cause
serious and permanent respiratory or other injury. Always use AS/NZS1716 approved
respiratory protection appropriate for the dust exposure. Direct particles away from
face and body.
WARNING: Always wear proper personal hearing protection that conforms to
AS/NZS1270 during use. Under some conditions and duration of use, noise from this
product may contribute to hearing loss.
CAUTION: When not in use, place tool on its side on a stable surface where it
will not cause a tripping or falling hazard. Some tools with large battery packs will
stand upright on the battery pack but may be easily knocked over.
• The label on your tool may include the following symbols. The symbols and their
definitions are as follows:
V ......................volts
A .........................amperes
Hz ....................hertz
W ........................watts
or AC ............alternating current
or AC/DC......alternating or
...........................direct current
no .......................no load speed
n .........................rated speed
.......................earthing terminal
.......................safety alert symbol
IPM .....................impacts per minute
SPM ....................strokes per minute
SAVE ALL WARNINGS AND INSTRUCTIONS FOR
FUTURE REFERENCE
Important Safety Instructions for All Battery Packs
When ordering replacement battery packs, be sure to include catalog number and
voltage. Consult the chart at the end of this manual for compatibility of chargers and
battery packs.
The battery pack is not fully charged out of the carton. Before using the battery pack
and charger, read the safety instructions below. Then follow charging procedures
outlined.
READ ALL INSTRUCTIONS
WARNING:
• Do not charge or use battery in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Inserting or removing the battery
from the charger may ignite the dust or fumes.
• Never force battery pack into charger. Do not modify battery pack in any
way to fit into a non-compatible charger as battery pack may rupture
causing serious personal injury. Consult the chart at the end of this manual for
compatibility of batteries and chargers.
• Charge the battery packs only in DEWALT chargers.
• DO NOT splash or immerse in water or other liquids.
4
Important Safety Instructions for All Battery Chargers
• Do not store or use the tool and battery pack in locations where the
temperature may reach or exceed 40 ЛљC (105 ЛљF) (such as outside sheds or
metal buildings in summer).
WARNING: Fire hazard. Never attempt to open the battery pack for any reason. If
battery pack case is cracked or damaged, do not insert into charger. Do not crush,
drop or damage battery pack. Do not use a battery pack or charger that has received
a sharp blow, been dropped, run over or damaged in any way (i.e., pierced with a nail,
hit with a hammer, stepped on). Damaged battery packs should be returned to service
center for recycling.
WARNING: Fire hazard. Do not store or carry battery so that metal objects can
contact exposed battery terminals. For example, do not place battery in aprons,
pockets, tool boxes, product kit boxes, drawers, etc., with loose nails, screws,
keys, etc. Transporting batteries can possibly cause fires if the battery terminals
inadvertently come in contact with conductive materials such as keys, coins,
hand tools and the like. The US Department of Transportation Hazardous Material
Regulations (HMR) actually prohibit transporting batteries in commerce or on
airplanes (i.e., packed in suitcases and carry-on luggage) UNLESS they are properly
protected from short circuits. So when transporting individual batteries, make sure
that the battery terminals are protected and well insulated from materials that could
contact them and cause a short circuit.
SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (Li-Ion)
• Do not incinerate the battery pack even if it is severely damaged or is
completely worn out. The battery pack can explode in a fire. Toxic fumes and
materials are created when lithium ion battery packs are burned.
• If battery contents come into contact with the skin, immediately wash area
with mild soap and water. If battery liquid gets into the eye, rinse water over the
open eye for 15 minutes or until irritation ceases. If medical attention is needed,
the battery electrolyte is composed of a mixture of liquid organic carbonates and
lithium salts.
• Contents of opened battery cells may cause respiratory irritation. Provide fresh
air. If symptoms persists, seek medical attention.
WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark or
flame.
SAVE THESE INSTRUCTIONS: This manual contains important safety and operating
instructions for battery chargers.
• Before using charger, read all instructions and cautionary markings on charger,
battery pack, and product using battery pack.
WARNING: Shock hazard. Do not allow any liquid to get inside charger. Electric
shock may result.
CAUTION: Burn hazard. To reduce the risk of injury, charge only DEWALT
rechargeable batteries. Other types of batteries may burst causing personal injury and
damage.
NOTICE: Under certain conditions, with the charger plugged in to the power supply,
the charger can be shorted by foreign material. Foreign materials of a conductive
nature such as, but not limited to, grinding dust, metal chips, steel wool, aluminum
foil, or any buildup of metallic particles should be kept away from charger cavities.
Always unplug the charger from the power supply when there is no battery pack in
the cavity. Unplug charger before attempting to clean.
WARNING:
• DO NOT attempt to charge the battery pack with any chargers other than the
ones in this manual. The charger and battery pack are specifically designed to
work together.
• These chargers are not intended for any uses other than charging DEWALT
rechargeable batteries. Any other uses may result in risk of fire, electric shock
or electrocution.
• Do not expose charger to rain or snow.
• Pull by plug rather than cord when disconnecting charger. This will reduce risk
of damage to electric plug and cord.
• Make sure that cord is located so that it will not be stepped on, tripped over,
or otherwise subjected to damage or stress.
• Do not use an extension cord unless it is absolutely necessary. Use
of improper extension cord could result in risk of fire, electric shock, or
electrocution.
• When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric
shock.
5
• Do not place any object on top of charger or place the charger on a soft
surface that might block the ventilation slots and result in excessive internal
heat. Place the charger in a position away from any heat source. The charger is
ventilated through slots in the top and the bottom of the housing.
• Do not operate charger with damaged cord or plug.
• Do not operate charger if it has received a sharp blow, been dropped, or
otherwise damaged in any way. Take it to an authorized service center.
• Do not disassemble charger; take it to an authorized service center when
service or repair is required. Incorrect reassembly may result in a risk of
electric shock, electrocution or fire.
• Disconnect the charger from the outlet before attempting any cleaning. This
will reduce the risk of electric shock. Removing the battery pack will not reduce
this risk.
• NEVER attempt to connect 2 chargers together.
• The charger is designed to operate on standard 230 V household electrical
power. Do not attempt to use it on any other voltage. This does not apply to the
vehicular charger.
FIG. 1
H
DCB107
Indicator Light Operation
DCB100-XE
Chargers
Your tool uses a DEWALT charger. Be sure to read all safety instructions before using
your charger. Consult the chart on the back cover of this manual for compatibility of
chargers and battery packs.
Charging Procedure (Fig. 1)
DCB105-XE
1. Plug the charger into an appropriate outlet before inserting battery pack.
2. Insert the battery pack (H) into the charger, as shown in Figure 1, making sure
the pack is fully seated in charger. The red (charging) light will blink continuously
indicating that the charging process has started.
3. The completion of charge will be indicated by the red light remaining ON
continuously. The pack is fully charged and may be used at this time or left in the
charger.
PACK CHARGING
PACK CHARGED
HOT/COLD DELAY
x
PROBLEM PACK OR CHARGER
PROBLEM POWERLINE
6
LEAVING THE BATTERY PACK IN THE CHARGER
The charger and battery pack can be left connected with the charge indicator showing
Pack Charged.
WEAK BATTERY PACKS: Weak batteries will continue to function but should not be
expected to perform as much work.
FAULTY BATTERY PACKS: This charger will not charge a faulty battery pack.
NOTE: This could also mean a problem with a charger.
DCB107-XE, DCB112-XE
PACK CHARGING
PACK CHARGED
HOT/COLD DELAY
PROBLEM POWER LINE (DCB100, DCB105)
Some chargers have a problem powerline indicator. When the charger is used with
some portable power sources such as generators or sources that convert DC to AC,
the charger may temporarily suspend operation, flashing the red light with two fast
blinks followed by a pause. This indicates the power source is out of limits.
Charge Indicators
Some chargers are designed to detect certain problems that can arise with battery
packs. If this occurs, re-insert battery pack into the charger. If the problem persists,
try a different battery pack to determine if the charger is OK. If the new pack charges
correctly, then the original pack is defective and should be returned to a service center
or other collection site for recycling. If the new battery pack elicits the same trouble
indication as the original, have the charger tested at an authorized service center.
NOTE: On the DCB100-XE and DCB105-XE, problems are indicated by the red light
flashing at a fast rate.
HOT/COLD PACK DELAY
DCB100-XE, DCB105-XE
The DCB100-XE and DCB105-XE have a Hot/Cold Pack Delay feature: when the
charger detects a battery that is hot, it automatically starts a Hot Pack Delay,
suspending charging until the battery has cooled. After the battery has cooled, the
charger automatically switches to the Pack Charging mode. This feature ensures
maximum battery life. The red light flashes long, then short while in the Hot/Cold Pack
Delay mode.
DCB107-XE, DCB112-XE
The DCB107-XE and DCB112-XE chargers have a hot/cold delay feature: when the
charger detects a battery that is hot, it automatically delays charging until the battery has
cooled. When the charger detects a battery that is cold, it automatically delays charging
until the battery has warmed.
The red light will continue to blink, but a yellow indicator light will be illuminated during
this operation. Once the battery has cooled, the yellow light will turn off and the charger
will resume the charging procedure.
Important Charging Notes
1. Longest life and best performance can be obtained if the battery pack is charged
when the air temperature is between 18 and 24 ЛљC (65 and 75 ЛљF). DO NOT
charge the battery pack in an air temperature below +4 ЛљC (+40 ЛљF), or above
+40 ЛљC (+105 ЛљF). This is important and will prevent serious damage to the
battery pack.
2. The charger and battery pack may become warm to touch while charging. This
is a normal condition, and does not indicate a problem. To facilitate the cooling
of the battery pack after use, avoid placing the charger or battery pack in a warm
environment such as in a metal shed, or an uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp or other appliance;
b. Check to see if receptacle is connected to a light switch which turns power off
when you turn out the lights;
c. Move charger and battery pack to a location where the surrounding air
temperature is approximately 18–24 ˚C (65–75 ˚F);
d. If charging problems persist, take the tool, battery pack and charger to your
local service center.
4. The battery pack should be recharged when it fails to produce sufficient power
on jobs which were easily done previously. DO NOT CONTINUE to use under
these conditions. Follow the charging procedure. You may also charge a partially
used pack whenever you desire with no adverse affect on the battery pack.
7
5. Foreign materials of a conductive nature such as, but not limited to, grinding
dust, metal chips, steel wool, aluminum foil, or any buildup of metallic particles
should be kept away from charger cavities. Always unplug the charger from the
power supply when there is no battery pack in the cavity. Unplug charger before
attempting to clean.
6. Do not freeze or immerse charger in water or any other liquid.
WARNING: Shock hazard. Don’t allow any liquid to get inside charger. Electric
shock may result.
CAUTION: Never attempt to open the battery pack for any reason. If the plastic
housing of the battery pack breaks or cracks, return to a service center for recycling.
FIG. 2
F
D
E
C
B
A
Storage Recommendations
1. The best storage place is one that is cool and dry, away from direct sunlight and
excess heat or cold.
2. For long storage, it is recommended to store a fully charged battery pack in a
cool dry place out of the charger for optimal results.
NOTE: Battery packs should not be stored completely depleted of charge. The battery
pack will need to be recharged before use.
I
G
J
H
SAVE THESE INSTRUCTIONS FOR FUTURE USE
COMPONENTS (Fig. 2)
DCD710-XE
WARNING: Never modify the tool or any part of it. Damage or personal injury
could result.
A. Variable speed trigger switch
G. Battery release button
B. Forward/reverse button
H. Battery pack
C. Worklight
I. Belt hook (optional accessory)
D. Torque adjustment collar
J. Belt hook screw
E. Gear shifter
F. Keyless chuck
INTENDED USE
This drill/driver is designed for light fastening and drilling applications.
DO NOT use under wet conditions or in presence of flammable liquids or gases.
This drill/driver is a professional power tool. DO NOT let children come into contact
with the tool. Supervision is required when inexperienced operators use this tool.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal injury, place the forward/
reverse button in the lock-off position or turn tool off and disconnect battery pack
before making any adjustments or removing/installing attachments or accessories.
Belt Hook (Optional Accessory)
WARNING: To reduce the risk of serious personal injury, place the forward/
reverse button in the lock-off position or turn tool off and disconnect battery pack
before making any adjustments or removing/installing attachments or accessories.
WARNING: To reduce the risk of serious personal injury, DO NOT suspend tool
overhead or suspend objects from the belt hook. ONLY hang tool’s belt hook from
a work belt.
8
tool will operate. For maximum tool life, use variable speed only for starting holes or
fasteners.
NOTE: Continuous use in variable speed range is not recommended. It may damage
the switch and should be avoided.
WARNING: To reduce the risk of serious personal injury, ensure the screw
holding the belt hook is secure.
IMPORTANT: When attaching or replacing the belt hook, use only the screw (J) that is
provided. Be sure to securely tighten screw.
The belt hook (I) can be be attached to either side of the tool using only the screw (J)
provided, to accommodate left- or right- handed users. If the hook is not desired at
all, it can be removed from the tool.
To move belt hook, remove the screw (J) that holds the belt hook in place then
reassemble on the opposite side. Be sure to securely tighten screw.
Forward/Reverse Control Button (Fig. 2)
A forward/reverse control button (B) determines the direction of the tool and also
serves as a lock off button.
To select forward rotation, release the trigger switch and depress the forward/reverse
control button on the right side of the tool.
To select reverse, depress the forward/reverse control button on the left side of the
tool. The center position of the control button locks the tool in the off position. When
changing the position of the control button, be sure the trigger is released.
NOTE: The first time the tool is run after changing the direction of rotation, you may
hear a click on start up. This is normal and does not indicate a problem.
OPERATION
WARNING: To reduce the risk of serious personal injury, place the forward/
reverse button in the lock-off position or turn tool off and disconnect battery pack
before making any adjustments or removing/installing attachments or accessories.
Installing and Removing the Battery Pack (Fig. 3)
Worklights (Fig. 2)
NOTE: Make sure your battery pack is fully charged.
To install the battery pack (H) into the tool handle, align the battery pack with the
rails inside the tool’s handle and slide it into the handle until the battery pack is firmly
seated in the tool and ensure that it does not disengage.
FIG. 3
There is one worklight (C) located around the chuck collar (D). The worklight will
activate when the trigger switch is pulled.
NOTE: The worklights are for lighting the immediate work surface and are not
intended to be used as a flashlight.
G
Torque Adjustment Collar (Fig. 2, 4)
H
FIG. 4
The torque adjustment collar (D) is clearly marked with
numbers and a drill bit symbol. The collar should be rotated
until the desired setting is located at the top of the tool.
Locators are provided in the collar to eliminate the guess work
when selecting fastening torque. The higher the number on the D
collar, the higher the torque and the larger the fastener which
can be driven. To lock the clutch for drilling operations, move
to the drill bit position.
E
NOTE: When using the drill/driver for drilling holes, be sure
that the torque adjusting collar is set so the figure of the drill is
aligned with the center line on the top of the tool. Failure to do
this will allow the clutch to slip while attempting to drill.
To remove the battery pack from the tool, press the release button (G) and firmly pull
the battery pack out of the tool handle. Insert it into the charger as described in the
charger section of this manual.
Variable Speed Trigger Switch (Fig. 2)
To turn the tool on, squeeze the trigger switch (A). To turn the tool off, release the
trigger switch. Your tool is equipped with a brake. The chuck will stop when the trigger
switch is fully released. The variable speed switch enables you to select the best
speed for a particular application. The more you squeeze the trigger, the faster the
9
Dual Range Gearing (Fig. 2, 4)
6 mm or greater size. Using a wooden mallet or similar object, strike the longer end in
the clockwise direction, as shown. This will loosen the screw inside the chuck.
Open chuck jaws fully, insert screwdriver (or Torx tool if required) into front of chuck
between jaws to engage screw head. Remove screw by turning clockwise (left-handthread). Place hex key in chuck and tighten, as shown in Figure 6. Using a wooden
mallet or similar object, strike key sharply in the counterclockwise direction. This will
loosen the chuck so that it can be unscrewed by hand.
The dual range feature of your driver/drill allows you to shift gears for greater versatility.
To select the low speed, high torque setting, turn the tool off and permit to stop. Slide
the gear shifter (E) forward (towards the chuck). To select the high speed, low torque
setting, turn the tool off and permit to stop. Slide the gear shifter back (away from
chuck).
NOTE: Do not change gears when the tool is running. If you are having trouble changing
gears, make sure that the dual range gear shifter is either completely pushed forward or
completely pushed back.
Keyless Single Sleeve Chuck
(Fig. 5)
FIG. 5
Your tool features a keyless chuck with one
rotating sleeve for one-handed operation of the
chuck. To insert a drill bit or other accessory,
follow these steps.
1. Lock the trigger in the OFF position as
previously described.
2. Grasp the black sleeve of the chuck
with one hand and use the other hand
to secure the tool. Rotate the sleeve
counterclockwise far enough to accept the desired accessory.
3. Insert the accessory about 19 mm into the chuck and tighten securely by rotating
the chuck sleeve clockwise with one hand while holding the tool with the other. Your
tool is equipped with an automatic spindle lock mechanism. This allows you to open
and close the chuck with one hand.
To release the accessory, repeat step 2 above.
WARNING: Do not attempt to tighten drill bits (or any other accessory) by gripping
the front part of the chuck and turning the tool on. Damage to the chuck and personal
injury may result. Always lock off trigger switch when changing accessories.
Be sure to tighten chuck with one hand on the chuck sleeve and one hand holding the
tool for maximum tightness.
CHUCK REMOVAL (FIG. 4, 6)
Turn the adjustment collar (D) to the “drill” position and gear shifter (E) to position 1
(low speed). Tighten the chuck around the shorter end of a hex key (not supplied) of
FIG. 6
FIG. 7
CHUCK INSTALLATION (FIG. 7)
Screw the chuck on by hand as far as it will go and insert screw (left-hand thread).
Tighten screw securely. Tighten the chuck around the shorter end of a 6.4 mm
or larger hex key (not supplied) strike the longer end in the clockwise direction
with a wooden mallet, as shown. Tighten the screw once again by turning in a
counterclockwise direction.
Drill Operation (Fig. 2)
WARNING: To reduce the risk of serious personal injury, turn tool off and
disconnect tool from power source before making any adjustments or removing/
installing attachments or accessories.
WARNING: To reduce the risk of personal injury, ALWAYS ensure workpiece is
anchored or clamped firmly. If drilling thin material, use a wood “back-up” block to
prevent damage to the material.
Turn the collar (D) to the drill bit symbol for drilling. Select the desired speed/torque
range using the gear shifter (E) to match the speed and torque to the planned operation.
10
1. Use sharp drill bits only. For WOOD, use twist drill bits, spade bits, or hole saws.
For METAL, use high-speed steel (HSS) twist drill bits or hole saws.
2. Always apply pressure in a straight line with the bit. Use enough pressure to keep
drill biting, but do not push hard enough to stall the motor or deflect the bit.
3. Hold tool firmly with both hands to control the twisting action of the drill.
WARNING: The drill may stall if overloaded causing a sudden twist. Always expect
the stall. Grip the drill firmly with both hands to control the twisting action and avoid
injury.
4. IF DRILL STALLS, it is usually because it is being overloaded or improperly used.
RELEASE TRIGGER IMMEDIATELY, remove drill bit from work, and determine
cause of stalling. DO NOT CLICK TRIGGER ON AND OFF IN AN ATTEMPT TO
START A STALLED DRILL — THIS CAN DAMAGE THE DRILL.
5. To minimize stalling or breaking through the material, reduce pressure on drill and
ease the bit through the last fractional part of the hole.
6. Keep the motor running when pulling the bit back out of a drilled hole. This will
help prevent jamming.
7. With variable speed drills there is no need to center punch the point to be drilled.
Use a slow speed to start the hole and accelerate by squeezing the trigger harder
when the hole is deep enough to drill without the bit skipping out.
Operation as a Screwdriver (Fig. 2)
Select the desired speed/torque range using the dual range gear shifter (E) on the top
of tool to match the speed and torque to the planned operation.
Insert the desired fastener accessory into the chuck (F) as you would any drill bit.
Make a few practice runs in scrap or unseen areas to determine the proper position of
the clutch collar (D).
MAINTENANCE
WARNING: To reduce the risk of serious personal injury, place the forward/
reverse button in the lock-off position or turn tool off and disconnect battery pack
before making any adjustments or removing/installing attachments or accessories.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once
a week. To minimize the risk of eye injury, always wear AS/NZS1337 approved eye
protection when performing this.
WARNING: Never use solvents or other harsh chemicals for cleaning the
non-metallic parts of the tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with water and mild soap. Never let
any liquid get inside the tool; never immerse any part of the tool into a liquid.
CHARGER CLEANING INSTRUCTIONS
WARNING: Shock hazard. Disconnect the charger from the AC outlet before
cleaning. Dirt and grease may be removed from the exterior of the charger using a
cloth or soft non-metallic brush. Do not use water or any cleaning solutions.
Repairs
This charger and battery pack are not serviceable. Servicing at an authorized service
centre is required to avoid damage to static sensitive internal components.
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement) should be performed by certified
service centers or other qualified service organizations, always using identical
replacement parts.
Accessories
WARNING: Since accessories, other than those offered by DEWALT, have not been
tested with this product, use of such accessories with this tool could be hazardous.
To reduce the risk of injury, only DEWALT recommended accessories should be used
with this product.
Recommended accessories for use with your tool are available at extra cost from
your local service center. If you need any assistance in locating any accessory, please
contact Stanley Black & Decker, 82 Taryn Drive, Epping, VIC 3076 Australia or call
1800 338 002 or (NZ) 0800 339 258.
DEWALT BATTERY AND CHARGER SYSTEMS
Cat. Number Voltage Amp Hour
DCB360
DCB361
DC9360
DE0240-XJ
DW0242
DW0240
DC9096
DC9180
DCB180
DCB181
DCB182
DCB183
DCB184
DCB185
DW9096
DE9095-XJ
DC9091
DC9144
DCB140
DCB141
DCB142
DCB143
DCB144
DCB145
DE9094
DE9091-XJ
DW9091
DC9071
DE9071-XJ
DE9074-XJ
DW9050
DW9071
DW9072
DCB120
DCB123
DCB125
DCB127
DW9063
DW9062
DW9061
DW9048
DCB080
DW9057
DW9046
Chargers/Charge Time
Output
Nominal
Battery
36
36
36
24
24
24
18
18
18
18
18
18
18
18
18
18
14.4
14.4
14.4
14.4
14.4
14.4
14.4
14.4
14.4
14.4
14.4
12
12
12
12
12
12
10.8
10.8
10.8
10.8
9.6
9.6
9.6
9.6
7.2
7.2
7.2
4.0
2.0
2.2
2.0
2.0
1.7
2.4
2.0
3.0
1.5
4.0
2.0
5.0
1.3
2.4
2.0
2.4
2.0
3.0
1.5
4.0
2.0
5.0
1.3
1.3
2.0
1.7
2.4
2.0
1.25
1.3
1.7
1.2
1.3
1.5
1.3
2.0
1.25
1.3
1.7
1.3
1.0
1.25
1.3
230 Volts
97014
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
60
X
X
X
X
X
X
X
45
45
45
60
60
45
40
60
45
X
X
X
X
45
45
60
40
X
45
40
12 Volts
98014 DW9106 DW9107 DW9108 DW9115 DW9116 DW9117 DW9118 DE9116 DE9118 DW911 DC011 DW0245 DE0246
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
60
X
X
X
X
X
X
X
45
45
45
60
60
45
40
60
45
X
X
X
X
45
45
60
40
X
45
40
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
60
X
X
X
X
X
X
X
45
45
45
60
60
45
40
60
45
X
X
X
X
45
45
60
40
X
45
40
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
60
X
X
X
X
X
X
X
30
45
45
60
45
30
X
45
30
X
X
X
X
30
30
45
X
X
30
X
X
X
X
X
X
X
60
X
X
X
X
X
X
X
60
60
60
X
X
X
X
X
X
X
30
45
45
60
45
30
X
45
30
X
X
X
X
30
30
45
X
X
30
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
15
X
X
X
X
X
X
X
15
15
15
15
15
15
15
15
15
X
X
X
X
15
15
15
15
X
15
15
X
X
X
X
X
X
60
X
X
X
X
X
X
X
60
60
60
X
X
X
X
X
X
X
30
45
45
60
45
30
X
45
30
X
X
X
X
30
30
45
X
X
30
X
X
X
X
X
X
X
20
X
X
X
X
X
X
X
20
20
15
X
X
X
X
X
X
X
12
15
15
15
15
12
X
15
12
X
X
X
X
12
12
15
X
X
12
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
60
X
X
X
X
X
X
X
60
90
90
60
90
60
X
90
60
X
X
X
X
60
60
90
X
X
60
X
X
X
X
X
X
X
60
X
X
X
X
X
X
X
60
60
60
X
X
X
X
X
X
X
30
45
45
60
45
30
X
45
30
X
X
X
X
30
30
45
X
X
30
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
60
X
X
X
X
X
X
X
60
90
90
60
90
60
X
90
60
X
X
X
X
60
60
90
X
X
60
X
X
X
X
X
X
X
60
X
X
X
X
X
X
X
60
60
60
X
X
X
X
X
X
X
30
45
45
60
45
30
X
45
30
X
X
X
X
30
30
45
X
X
30
X
X
X
X
X
X
X
60
X
X
X
X
X
X
X
60
60
60
X
X
X
X
X
X
X
30
45
45
60
45
30
X
45
30
X
X
X
X
30
30
45
X
X
30
X
X
X
X
60
60
60
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
60
60
60
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
DC9000
DC9310
DCB095
75
45
60
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
60
60
X
X
X
X
X
X
60
60
60
60
X
X
X
X
X
X
30
45
45
60
45
30
X
45
30
X
X
X
X
30
30
45
X
X
30
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
60
X
X
DCB100 DCB103 DCB105 DCB106 DCB107 DCB112 DCR017 DCB119 DW9109 DC9319
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
40
40
40
65
X
X
X
X
X
X
X
X
X
X
X
X
X
60
60
55
30
70
40
90
25
60
60
60
60
55
30
90
40
90
25
30
45
45
60
45
30
X
45
30
40
40
25
40
30
30
45
X
X
30
X
X
X
X
X
X
X
X
X
55
30
70
40
90
25
X
X
X
X
55
30
90
40
90
25
X
X
X
X
X
X
X
X
X
40
40
25
40
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
140
70
185
90
240
60
X
X
X
X
X
X
X
X
240
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
140
70
185
90
240
60
X
X
X
X
140
70
185
90
240
60
X
X
X
X
X
X
X
X
X
60
70
60
90
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
90
45
120
60
150
40
X
X
X
X
90
45
120
60
150
40
X
X
X
X
X
X
X
X
X
40
45
40
60
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
90
45
120
60
150
40
X
X
X
X
90
45
120
60
150
40
X
X
X
X
X
X
X
X
X
40
45
40
60
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
90
40
117
60
150
35
X
X
X
X
90
40
117
60
150
35
X
X
X
X
X
X
X
X
X
40
40
35
60
X
X
X
X
X
X
X
X
X
X
X
X
X
60
X
X
X
X
X
X
X
60
60
60
X
X
X
X
X
X
X
30
45
45
60
45
30
X
45
30
X
X
X
X
30
30
45
X
X
30
X
X
X
X
X
X
X
60
60
X
X
X
X
X
X
60
60
60
60
X
X
X
X
X
X
30
45
45
60
45
30
X
45
30
X
X
X
X
30
30
45
X
X
30
X
X Indicates that the battery pack is not compatible with that specific charger.
All charge times are approximate. Actual charge time may vary.
Read the instruction manual for more specific information.
The battery voltage is nominal, it can measure above or below depending on the state of charge.
Stanley Black & Decker
82 Taryn Drive, Epping, VIC 3076 Australia • 1800 338 002 (Aust) or 0800 339 258 (NZ)
www.dewalt.com.au • www.dewalt.co.nz
(APR14) Part No. N376441 DCD710-XE Copyright В© 2010, 2011, 2014 DEWALT
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip;
the kit box configuration; and the array of lozenge-shaped humps on the surface of the tool.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement