Flygt 3152 - Alaska Pump and Supply

Flygt 3152 - Alaska Pump and Supply
Installation,
Operation, and
Maintenance Manual
Flygt 3152
Table of Contents
Table of Contents
Introduction and Safety.........................................................................................................................3
Safety.....................................................................................................................................................3
Safety message levels......................................................................................................................3
User health and safety......................................................................................................................4
Safety regulations for Ex-approved products in potentially explosive atmospheres..............6
Environmental safety........................................................................................................................7
Product warranty.................................................................................................................................7
Spare parts........................................................................................................................................8
Transportation and Storage..................................................................................................................9
Inspect the unit upon delivery...........................................................................................................9
Receive the unit.................................................................................................................................9
Unpack the unit.................................................................................................................................9
Lifting guidelines.................................................................................................................................9
Store the unit.....................................................................................................................................10
Product Description.............................................................................................................................11
Pump design......................................................................................................................................11
Parts....................................................................................................................................................12
Monitoring equipment.....................................................................................................................13
Optional sensors.............................................................................................................................13
The data plate....................................................................................................................................13
Approvals...........................................................................................................................................14
Product denomination......................................................................................................................15
Installation.............................................................................................................................................17
Install the pump.................................................................................................................................17
Install with P-installation.................................................................................................................17
Install with S-installation.................................................................................................................18
Install with T/Z-installation.............................................................................................................19
Make the electrical connections......................................................................................................21
General precautions.......................................................................................................................21
Requirements..................................................................................................................................21
Cables..............................................................................................................................................21
Earthing (Grounding).....................................................................................................................22
Connect the motor cable to the pump........................................................................................22
Connect the motor cable to the starter and monitoring equipment.......................................23
Cable charts....................................................................................................................................24
Check the impeller rotation.............................................................................................................30
Operation..............................................................................................................................................31
Distance to wet areas........................................................................................................................31
Start the pump...................................................................................................................................31
Maintenance.........................................................................................................................................32
Precautions.........................................................................................................................................32
Maintenance guidelines...................................................................................................................32
Torque values....................................................................................................................................32
Change the oil...................................................................................................................................33
Replace the wear rings.....................................................................................................................35
Replace the wear ring in the pump housing, diffuser ring, or suction cover..........................36
Replace the impeller wear ring.....................................................................................................37
Flygt 3152 Installation, Operation, and Maintenance Manual
1
Table of Contents
Replace the impeller.........................................................................................................................38
Remove the impeller and the wear protections ........................................................................40
Install the impeller and the wear protections.............................................................................41
Adjust the lower wear protection.................................................................................................42
Remove the impeller: F..................................................................................................................42
Install the impeller: F......................................................................................................................43
Service the pump..............................................................................................................................45
Inspection........................................................................................................................................46
Major overhaul................................................................................................................................47
Service in case of alarm.................................................................................................................47
Troubleshooting...................................................................................................................................48
Introduction.......................................................................................................................................48
The pump does not start..................................................................................................................48
The pump does not stop when a level sensor is used.................................................................49
The pump starts-stops-starts in rapid sequence...........................................................................49
The pump runs but the motor protection trips.............................................................................50
The pump delivers too little or no water........................................................................................50
Technical Reference............................................................................................................................52
Application limits...............................................................................................................................52
Motor data..........................................................................................................................................52
2
Flygt 3152 Installation, Operation, and Maintenance Manual
Introduction and Safety
Introduction and Safety
Safety
WARNING:
• The operator must be aware of safety precautions to prevent physical injury.
• Any pressure-containing device can explode, rupture, or discharge its contents if it is
over-pressurized. Take all necessary measures to avoid over-pressurization.
• Operating, installing, or maintaining the unit in any way that is not covered in this manual
could cause death, serious personal injury, or damage to the equipment. This includes
any modification to the equipment or use of parts not provided by Xylem. If there is a
question regarding the intended use of the equipment, please contact an Xylem
representative before proceeding.
• Do not change the service application without the approval of an authorized Xylem
representative.
• Never operate the pump without safety devices installed.
• Never operate the pump with the discharge valve closed.
NOTICE:
For information about how to transport and store the pump, see Transportation and
Storage in the Installation, Operation and Maintenance manual.
Safety message levels
Definitions
Safety message level
Indication
DANGER:
A hazardous situation which, if not avoided, will result in
death or serious injury
WARNING:
A hazardous situation which, if not avoided, could result
in death or serious injury
CAUTION:
A hazardous situation which, if not avoided, could result
in minor or moderate injury
Electrical Hazard:
The possibility of electrical risks if instructions are not
followed in a proper manner
Flygt 3152 Installation, Operation, and Maintenance Manual
3
Introduction and Safety
Safety message level
NOTICE:
Indication
• A potential situation which, if not avoided, could
result in an undesirable result or state
• A practice not related to personal injury
User health and safety
General precautions
The product is designed for use in liquids that can be hazardous to health. Observe these
rules when working with the product:
• Make sure that all personnel who work with sewage systems are vaccinated against
diseases to which they may be exposed.
• Observe strict personal cleanliness.
Safety equipment
Use safety equipment according to the company regulations. Use this safety equipment
within the work area:
• Helmet
• Safety goggles (with side shields)
• Protective shoes
• Protective gloves
• Gas mask
• Hearing protection
NOTICE:
The noise level of the product is lower than 70 dB. However, the noise level of 70 dB
may be exceeded in some installations and at certain operating points on the
performance curve. Make sure that you understand the noise level requirements in the
environment where the pump is installed. Failure to do so may result in hearing loss or
violation of local laws.
The work area
Observe these regulations and warnings in the work area:
• Always keep the work area clean.
• Pay attention to the risks presented by gas and vapors in the work area.
• Avoid all electrical dangers. Pay attention to the risks of electric shock or arc flash
hazards.
Product and product positioning requirements
Observe these requirements for the product and the product positioning:
• Vent the tank of a sewage station in accordance with local plumbing codes.
• Never operate a pump unless safety devices are installed.
Electrical connections regulations
Electrical connections must be made by certified electricians in compliance with all
international, national, state, and local regulations.
Observe these guidelines and warnings for electrical connections:
• Make sure that the product is isolated from the power supply and cannot be energized
by mistake. This guideline also applies to the control circuit.
• Make sure that the thermal contacts are connected to a protection circuit according to
the product approvals, and that they are in use.
4
Flygt 3152 Installation, Operation, and Maintenance Manual
Introduction and Safety
• Make sure that the cable and the cable entry have not been damaged during shipping.
• Use only the screened cable when using a variable-frequency drive (VFD). The
screened cable is necessary to fulfill European CE requirements. Contact your Xylem
representative and ask your VFD supplier for electrical limitations. See also VFD
recommendation in article no. 893472.
Earthing (grounding)
Observe the following regulations for earthing (grounding) connections.
Earthing (grounding) regulation
Comment
All electric equipment must be earthed (grounded).
This rule applies to pumps and mixers as well as
monitoring equipment.
The earthing (grounding) conductors must be correctly
connected.
Failure to follow this rule could result in a fatal accident.
The earthing (grounding) conductors should always be
longer than the phase conductor/conductors.
If the motor cable is disconnected by mistake, the
earthing (grounding) conductor needs to be
disconnected last from its terminal. This rule applies to
both ends of the cable.
Risk of electrical shock or burn. You must connect an
additional earth- (ground-) fault protection device to the
earthed (grounded) connectors if persons are likely to
come into physical contact with the pump or pumped
liquids.
—
Precautions before work
Observe these safety precautions before you work with the product or are in connection
with the product:
• Provide a suitable barrier around the work area, for example, a guard rail.
• Make sure that all safety guards are in place and secure.
• Allow all system and pump components to cool before you handle them.
• Make sure that you have a clear path of retreat.
• Make sure that the product cannot roll or fall over and injure people or damage
property.
• Make sure that the lifting equipment is in good condition.
• Use a lifting harness, a safety line, and a breathing device as required.
• Make sure that the product is thoroughly clean.
• Make sure that there are no poisonous gases within the work area.
• Make sure that you have quick access to a first-aid kit.
• Disconnect and lock out power before servicing.
• Check the explosion risk before you weld or use electric hand tools.
Precautions during work
Observe these safety precautions when you work with the product or are in connection
with the product:
• Never work alone.
• Always wear protective clothing and hand protection.
• Stay clear of suspended loads.
• Always lift the product by its lifting device.
• Never lift the product by its motor cable or hose.
• Beware of the risk of a sudden start if the product is used with an automatic level
control.
• Beware of the starting jerk, which can be powerful.
• Rinse the components in water after you disassemble the pump.
Flygt 3152 Installation, Operation, and Maintenance Manual
5
Introduction and Safety
• Do not open any vent or drain valve or remove any plugs while the system is
pressurized. Make sure that the pump is isolated from the system and that pressure is
relieved before you disassemble the pump, remove plugs, or disconnect piping.
• Always bear in mind the risk of drowning, electrical accidents, and burn injuries.
Clean chemicals from the eyes
1. Hold your eyelids apart forcibly with your fingers.
2. Rinse the eyes for at least 15 minutes.
Use an eyewash or running water.
3. Seek medical attention.
Clean chemicals from the body
1. Remove contaminated clothing.
2. Wash the skin with soap and water for at least one minute.
3. Seek medical attention, if required.
Safety regulations for Ex-approved products in potentially explosive atmospheres
Guidelines for compliance
Compliance is only fulfilled when the pump is operated within its intended use, for
example within its intended hydraulic range. The conditions of the service must not be
changed without approval of an authorized Xylem representative. When installing or
maintaining explosion-proof pumps, follow these guidelines:
• Always install ATEX-approved equipment in compliance with the directive and
applicable standards (IEC/EN 60079–14).
• Always install explosion proof products according to ANSI/NFPA 70-2005.
WARNING:
This manual clearly identify accepted methods for disassembling units. These methods
must be adhered to. Trapped liquid can rapidly expand and result in a violent explosion
and injury. Never apply heat to impellers, propellers, or their retaining devices to aid in
their removal.
If there are any questions regarding these requirements, the intended use, or if the
equipment requires modification, contact an Xylem representative before you proceed.
Personnel requirements
Xylem disclaims all responsibility for work done by untrained and unauthorized personnel.
These are the personnel requirements for Ex-approved products in potentially explosive
atmospheres:
• All work on the product must be carried out by certified electricians and Xylemauthorized mechanics. Special rules apply to installations in explosive atmospheres.
• All users must know about the risks of electric current and the chemical and physical
characteristics of the gas and/or vapor present in hazardous areas.
• Any maintenance for Ex-approved products must conform to international and national
standards (for example IEC/EN 60079-17).
Product and product handling requirements
These are the product and product handling requirements for Ex-approved products in
potentially explosive atmospheres:
• Only use the product in accordance with the approved motor data stated on the
nameplates.
• The Ex-approved product must never run dry during normal operation. Dry running
during service and inspection is only permitted outside the classified area.
6
Flygt 3152 Installation, Operation, and Maintenance Manual
Introduction and Safety
• See the dimensional drawings of the product for the minimum permitted water level
according to the ATEX approval. Level-sensing equipment must be installed if the
product can be operated at less than the minimum submersion depth.
• Before you start working with the product, make sure that the product and the control
panel are isolated from the power supply and the control circuit, so they cannot be
energized.
• Do not open the product while it is energized or in an explosive gas atmosphere.
• Make sure that thermal contacts are connected to a protection circuit according to the
approval classification of the product.
• Intrinsically safe circuits are normally required for the automatic level-control system by
the level regulator if mounted in zone 0.
• The yield stress of fasteners must be in accordance with the approval drawing and the
product specification.
• Do not modify the equipment without approval from an authorized Xylem
representative.
• Only use parts that have been provided by an authorized Xylem representative.
Equipment for monitoring
For additional safety, use condition-monitoring devices. Condition-monitoring devices
include but are not limited to these devices:
• Level indicators
• Temperature detectors
Environmental safety
The work area
Always keep the pump station clean to avoid and/or discover emissions.
Recycling guidelines
Always recycle according to these guidelines:
1. If the unit or parts are accepted by an authorized recycling company, then follow
local recycling laws and regulations.
2. If the unit or parts are not accepted by an authorized recycling company, then return
them to the nearest Xylem representative.
Waste and emissions regulations
Observe these safety regulations regarding waste and emissions:
• Dispose appropriately of all waste.
• Handle and dispose of the pumped fluid in compliance with applicable environmental
regulations.
• Clean up all spills in accordance with safety and environmental procedures.
• Report all environmental emissions to the appropriate authorities.
Reference for electrical installation
For electrical installation requirements, consult your local electric utility.
Product warranty
Coverage
Xylem undertakes to remedy faults in products from Xylem under these conditions:
• The faults are due to defects in design, materials, or workmanship.
• The faults are reported to an Xylem representative within the warranty period.
• The product is used only under the conditions described in this manual.
• The monitoring equipment incorporated in the product is correctly connected and in
use.
Flygt 3152 Installation, Operation, and Maintenance Manual
7
Introduction and Safety
• All service and repair work is done by Xylem-authorized personnel.
• Genuine Xylem parts are used.
• Only Ex-approved spare parts and accessories authorized by Xylem are used in Exapproved products.
Limitations
The warranty does not cover faults caused by these situations:
• Deficient maintenance
• Improper installation
• Modifications or changes to the product and installation made without consulting
Xylem
• Incorrectly executed repair work
• Normal wear and tear
Xylem assumes no liability for these situations:
• Bodily injuries
• Material damages
• Economic losses
Warranty claim
Xylem products are high-quality products with expected reliable operation and long life.
However, should the need arise for a warranty claim, then contact your Xylem
representative.
Spare parts
Xylem guarantees that spare parts will be available for 15 years after the manufacture of
this product has been discontinued.
8
Flygt 3152 Installation, Operation, and Maintenance Manual
Transportation and Storage
Transportation and Storage
Inspect the unit upon delivery
Receive the unit
1. Inspect the package for damaged or missing items upon delivery.
2. Note any damaged or missing items on the receipt and freight bill.
3. File a claim with the shipping company if anything is out of order.
Unpack the unit
1. Remove packing materials from the unit.
Dispose of all packing materials in accordance with local regulations.
2. Inspect the unit to determine if any parts have been damaged or are missing.
3. Contact your Xylem representative if anything is out of order.
Lifting guidelines
General
The following are general guidelines for lifting the unit:
• Always use lifting equipment when handling the unit.
• When you use a lifting eyebolt or shackle for lifting the unit, make sure that the eyebolt
or shackle is fastened firmly before lifting.
• The unit can be transported either horizontally or vertically.
Precautions
WARNING:
• The unit might get stuck if it hangs at any angle when lifting or lowering along guide
bars. Make sure the unit hangs straight up and down from the lifting hook.
• Crush hazard. The unit and the components can be heavy. Use proper lifting methods
and wear steel-toed shoes at all times.
• Do not attach sling ropes to shaft ends.
• Stay clear of suspended loads.
• Always lift the unit by its lifting handle. Never lift the unit by the motor cable or by the
hose.
Flygt 3152 Installation, Operation, and Maintenance Manual
9
Transportation and Storage
Lifting equipment
The lifting equipment must fulfill the following requirements:
• The minimum height between the lifting hook and the floor must be sufficient to lift the
unit out of the sump. Contact Xylem for information.
• The lifting equipment must be able to hoist the unit straight up and down in the sump,
preferably without the need for resetting the lifting hook.
• The lifting equipment must be securely anchored and in good condition.
• The lifting equipment must support the entire assembly and must only be used by
authorized personnel.
• Two sets of lifting equipment must be used to lift the unit for repair work.
• The lifting equipment must be dimensioned to lift the unit with any remaining pumped
media (liquid) in it.
• The lifting equipment must not be oversized.
NOTICE:
Oversized lifting equipment could cause damage if the unit should stick when being
lifted.
Store the unit
1. After raising the unit, allow it to run for a short time to discharge all remaining pumped
media (liquid).
The unit is frost-proof while operating or immersed in liquid, but the impeller and the
shaft seal may freeze if the unit is raised in a temperature below freezing.
2. Store the unit in a covered and dry location free from heat, dirt, and vibrations.
3. If the unit is stored more than 6 months, rotate the shaft every other month to prevent
the seals from sticking together.
4. Before operating the unit after storage:
Condition
Action
The unit has been stored more than 6
months
Inspect the unit with special attention to the seals and the cable entry.
The impeller is frozen
Thaw the impeller by immersing the unit in liquid.
NOTICE:
Never use a naked flame to thaw the unit.
10
Flygt 3152 Installation, Operation, and Maintenance Manual
Product Description
Product Description
Pump design
The pump is submersible, and driven by an electric motor.
Intended use
The product is intended for moving waste water, sludge, raw and clean water. Always
follow the limits given in Application limits (page 52). If there is a question regarding the
intended use of the equipment, please contact an Xylem representative before
proceeding.
WARNING:
In explosive or flammable environments, only use Ex- or MSHA-approved pumps.
NOTICE:
Do NOT use the pump in highly corrosive liquids.
Spare parts
• Modifications to the unit or installation should only be carried out after consulting with
Xylem.
• Original spare parts and accessories authorized by Xylem are essential for compliance.
The use of other parts can invalidate any claims for warranty or compensation. For
more information contact your Xylem representative.
Flygt 3152 Installation, Operation, and Maintenance Manual
11
Product Description
Parts
7
6
4
3
2
5
1
12
Positio Part
n
Description
1
Impeller
A wide range of impellers are available for different applications and capacities.
2
Mechanical seal
The seals are made of:
• Inner seal: corrosion-resistant cemented carbide WCCR/WCCR
• Outer seal: corrosion-resistant cemented carbide WCCR/WCCR
3
Shaft
Stainless steel or carbon steel shaft with an integrated rotor.
4
Bearing
5
Oil housing
A housing with oil that lubricates and cools the seals, and acts as a buffer between the
pumped media (liquid) and the drive unit.
6
Cooling
The stator is cooled by either the surrounding media (liquid) or by forced circulation in a
cooling jacket.
7
Motor
For information about the motor, see Motor data (page 52).
• The main bearing consists of a two-row angular-contact ball bearing.
• The support bearing consists of a single-row roller bearing.
Flygt 3152 Installation, Operation, and Maintenance Manual
Product Description
Monitoring equipment
The following applies to the monitoring equipment of the pump:
• The stator incorporates three thermal contacts connected in series that activate the
alarm and stops the pump at overtemperature
• The thermal contacts open at 125°C (257°F).
• Ex-approved pumps must have thermal contacts connected to the control panel.
• The sensors must be connected to either the MiniCAS II monitoring equipment or an
equivalent equipment.
• The monitoring equipment must be of a design that makes automatic restart
impossible.
• Information in the junction box shows if the pump is equipped with optional sensors.
Optional sensors
Thermistor Thermistors are optional sensors for measuring the temperature. They are
connected in series in the stator and activate the alarm at overtemperature.
The sensors are only optional for standard pumps.
NOTICE:
Thermistor must never be exposed to voltages higher than 2.5 V. If the
voltage exceeds this value, for example when the control circuit is tested, the
thermistors will be destroyed.
FLS
FLS is a miniature float switch for detection of liquid in the stator housing. Due
to its design it is best suited for pumps in a vertical position. The FLS sensor is
installed in the bottom of the stator housing.
CLS
CLS is a sensor for detection of water in the oil housing. The sensor initiates an
alarm when the oil contains approximately 35% water. The sensor is installed
in the bearing housing/bearing holder with its sensing part in the oil housing.
The CLS sensor is not applicable to Ex-approved pumps.
NOTICE:
The CLS sensor body is made of glass. Handle the sensor with care.
One CLS and one FLS sensor can be used in the same pump, if they are connected in
parallel.
The data plate
The data plate is a metal label located on the main body of the pump. The data plate lists
key product specifications.
Flygt 3152 Installation, Operation, and Maintenance Manual
13
Product Description
Ex- and MSHA-approved products also have approval plates. They are described below, if
applicable.
3
2
1
4
24
23
5
22
6
21
7
20
8
9
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
10
11
12 13 14 15 16
17
18
19
Curve code/Propeller code
Serial number, see Product denomination (page 15)
Product number
Country of origin
Additional information
Phase; type of current; frequency
Rated voltage
Thermal protection
Thermal class
Rated shaft power
International standard
Degree of protection
Rated current
Rated speed
Maximum submergence
Direction of rotation: L=left, R=right
Duty class
Duty factor
Product weight
Locked rotor code letter
Power factor
Maximum ambient temperature
Read installation manual
Notified body/only for EN-approved Ex-products
Figure 1: The data plate
Approvals
This section describes the EN and FM approvals that explosion-proof products have. For
more information, please contact your Xylem representative. In addition to the data plate,
explosion-proof products also have either an EN or a FM approval plate.
EN
• European Norm
• ATEX Directive
• EN 50014, EN 50018, EN 1127-1
•
14
II 2 G EEx d IIB T4
Flygt 3152 Installation, Operation, and Maintenance Manual
Product Description
1
2
3
15
4
14
13
12
11
5
6
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
7
8
9
10
Approval
Approval authority + approval number
Approval for Class I
Approved drive unit
Stall time
Starting current/Rated current
Duty class
Duty factor
Input power
Rated speed
Controller
Additional information
Maximum ambient temperature
Serial number
ATEX marking
Figure 2: EN approval plate
EN approval for cable entry:
• Certificate number: INERIS 02ATEX9008 U
•
II 2 G or IM2 EEx d IIC or EEx dI
FM
This illustration describes the approval plate for Factory Mutual (FM) and the information
contained in its fields.
1
2
1.
2.
Temperature class
Maximum ambient temperature
Figure 3: FM approval plate
Product denomination
Flygt 3152 Installation, Operation, and Maintenance Manual
15
Product Description
Sales denomination
The sales denomination consists of the four-digit sales code and two letters that indicate
the hydraulic end and type of installation.
This is an example of a sales denomination, and an explanation of its parts.
NP 3085
1 2 3
1.
2.
3.
Hydraulic part
Installation type
Sales code
Product code
The product code consists of nine characters divided into two parts.
This is an example of a product code, and an explanation of its parts.
NP 3085.183
1
1.
2.
2
Sales denomination
Version
Serial number
The serial number is used for identification of an individual product, and is divided into
four parts.
This is an example of a serial number, and an explanation of its parts.
NP 3085.183 - 951 0163
1
1.
2.
3.
4.
16
2
3 4
Product code
Production year
Production cycle
Running number
Flygt 3152 Installation, Operation, and Maintenance Manual
Installation
Installation
Install the pump
WARNING:
• Before installing the pump, check that the cable and cable entry have not been
damaged during transportation.
• Note that special rules apply to installation in explosive atmospheres.
• Make sure that the pump cannot roll or fall over and injure people or damage property.
• Do not install CSA-approved products in locations that are classified as hazardous in the
national electric code, ANSI/NFPA 70-2005.
NOTICE:
• Do not run the pump dry.
• Never force piping to make a connection with a pump.
• Always remove all debris and waste material from the sump, inlet piping, and
discharge connection, before you install the pump.
These requirements apply:
• Use the pump dimensional drawing in order to ensure proper installation.
• In S-, T-, and Z-installations the pump must be equipped with cooling jacket
• Provide a suitable barrier around the work area, for example, a guard rail.
• Check the explosion risk before you weld or use electric hand tools.
• Always check the impeller rotation before lowering the pump into the pumped liquid.
Install with P-installation
In the P-installation, the pump is installed on a stationary discharge connection, and
operates either completely or partially submerged in the pumped liquid. These
requirements and instructions only apply when the installation is made according to the
dimensional drawing.
Figure 4: P-installation
Flygt 3152 Installation, Operation, and Maintenance Manual
17
Installation
These items are required:
• Guide bars
• Guide bar bracket for attaching the guide equipment to the access frame or to the
upper part of the sump
• Level regulators or other control equipment for start, stop, and alarm
• Cable holder for holding the cable and regulating the height of the level regulators
• Access frame (with covers) to which the upper guide bar bracket and cable holder can
be attached
• Discharge connection for connecting the pump to the discharge line
The discharge connection has a flange which fits the pump casing flange and a bracket
for attaching the guide equipment.
• Fasteners for the discharge connection
• Anchor bolts
1. Run a cable between the sump and the stator and monitoring equipment.
Make sure that the cable is neither sharply bent, nor pinched.
2. Install the access frame:
a) Place the access frame in position and align it horizontally.
b) Grout the frame in place.
3. Grout the anchor bolts in place.
Be careful when you align and position the discharge connection in relation to the
access frame.
4. Place the discharge connection in position, and tighten the nuts.
5. Install the guide bars:
a) Secure the guide bars in the bracket.
b) Check that the guide bars are placed vertically. Use a level or a plumb line.
6. Connect the discharge pipe to the discharge connection.
7. Prepare for the level regulator:
a) Bolt the cable holder to the access frame.
b) Attach the level regulator cable to the cable holder and adjust the height of the
level regulator.
c) Protect bolts and nuts with a corrosion-preventive compound.
8. Lower the pump along the guide bars.
9. Secure the motor cable:
a) Fasten the permanent lifting device to the pump and to the access frame. For
example, you can use a stainless-steel lifting chain with shackles.
b) Fasten the cable to the cable holder.
Make sure that the cable cannot be sucked into the pump inlet or that it is neither
sharply bent, or pinched. Support straps are required for deep installations.
c) Connect the motor cable and the starter and monitoring equipment according to
the separate instructions.
Make sure that the impeller rotation is correct. For more information, see Check the
impeller rotation (page 30).
Clean all debris from the sump before starting the pump.
Install with S-installation
In the S-installation, the pump is transportable and intended to operate either completely
or partially submerged in the pumped liquid. The pump is equipped with a connection for
hose or pipe and stands on a base stand.
18
Flygt 3152 Installation, Operation, and Maintenance Manual
Installation
These requirements and instructions only apply when the installation is made according to
the dimensional drawing. For information about the different installation types, see Parts
List.
Figure 5: S-installation
1. Run the cable so that it has no sharp bends, is not pinched, and cannot be sucked into
the pump inlet.
2. Connect the discharge line.
3. Lower the pump into the sump.
4. Place the pump on the base and make sure it cannot fall over or sink.
Alternatively, the pump can be suspended with a lifting chain just above the sump
bottom. Make sure that the pump cannot rotate at startup or during operation.
5. Connect the motor cable and the starter and monitoring equipment according to the
separate instructions.
Make sure that the impeller rotation is correct. For more information, see Check the
impeller rotation (page 30).
Install with T/Z-installation
• In the T-installation, the pump is installed in a vertical position in a dry well next to the
wet sump. These requirements and instructions only apply when the installation is
made according to the dimensional drawing.
• In the Z-installation, the pump is installed in a horizontal position on a support stand in
a dry well next to the wet sump, and a bell-mouth is connected to the inlet pipe. These
requirements and instructions are for Z-installations that comply to the dimensional
drawing.
Flygt 3152 Installation, Operation, and Maintenance Manual
19
Installation
Figure 7: Z-installation
Figure 6: T-installation
These items are required:
• Support stand and anchor bolts for anchoring the pump to a base
• Inlet elbow for connecting the suction line and discharge line
• Shut-off valves that allow you to remove the pump from service
• Air vent on the discharge side between the pump and the check valve
• Level regulators or other control equipment for start, stop, and alarm
NOTICE:
The risk of freezing is particularly high in T- or Z-installations.
1. Fasten the pump:
a) Use the anchor bolts to bolt the support stand to the concrete base.
b) Bolt the pump to the support stand and the suction connection.
2. Make sure that the pump is vertical for the T-installation or horizontal for the Zinstallation.
3. Connect the suction line and discharge line.
4. Connect the motor cable and the starter and monitoring equipment according to the
separate instructions.
Make sure that the impeller rotation is correct. For more information, see Check the
impeller rotation (page 30).
5. Make sure that the weight of the pump does not put strain on the piping.
20
Flygt 3152 Installation, Operation, and Maintenance Manual
Installation
Make the electrical connections
General precautions
Electrical Hazard:
• A certified electrician must supervise all electrical work. Comply with all local codes and
regulations.
• Before starting work on the pump, make sure that the pump and the control panel are
isolated from the power supply and cannot be energized. This applies to the control
circuit as well.
• Leakage into the electrical parts can cause damaged equipment or a blown fuse. Keep
the end of the motor cable above the liquid level.
• Make sure that all unused conductors are insulated.
• There is a risk of electrical shock or explosion if the electrical connections are not
correctly carried out or if there is fault or damage on the product.
CAUTION:
If the pump is equipped with automatic level control and/or internal contactor, there is a
risk of sudden restart.
Requirements
These general requirements apply for electrical installation:
• The supply authority must be notified before installing the pump if it will be connected
to the public mains. When the pump is connected to the public power supply, it may
cause flickering of incandescent lamps when started.
• The mains voltage and frequency must agree with the specifications on the data plate.
If the pump can be connected to different voltages, the connected voltage is specified
by a yellow sticker close to the cable entry.
• The fuses and circuit breakers must have the proper rating, and the pump overload
protection (motor protection breaker) must be connected and set to the rated current
according to the data plate and if applicable the cable chart. The starting current in
direct-on-line starting can be up to six times higher than the rated current.
• The fuse rating and the cables must be in accordance with the local rules and
regulations.
• If intermittent operation is prescribed, the pump must be provided with monitoring
equipment supporting such operation.
• The motor is convertible between different voltages, as stated on the data plate. This
conversion is done on the terminal board.
• The thermal contacts/thermistors must be in use.
Cables
These are the requirements to follow when you install cables:
• The cables must be in good condition, not have any sharp bends, and not be pinched.
• The sheathing must not be damaged and must not have indentations or be embossed
(with markings, etc.) at the cable entry.
• The cable entry seal sleeve and washers must conform to the outside diameter of the
cable.
• The minimum bending radius must not be below the accepted value.
Flygt 3152 Installation, Operation, and Maintenance Manual
21
Installation
• If using a cable which has been used before, a short piece must be peeled off when
refitting it so that the cable entry seal sleeve does not close around the cable at the
same point again. If the outer sheath of the cable is damaged, then replace the cable.
Contact an Xylem service shop.
• The voltage drop in long cables must be taken into account. The drive unit’s rated
voltage is the voltage measured at the cable connection point in the pump.
• The screened cable must be used according to the European CE requirements if a
Variable Frequency Drive (VFD) is used. For more information, contact your Xylem
representative (VFD-supplier).
Earthing (Grounding)
Electrical Hazard:
• You must earth (ground) all electrical equipment. This applies to the pump equipment,
the driver, and any monitoring equipment. Test the earth (ground) lead to verify that it is
connected correctly.
• If the motor cable is jerked loose by mistake, the earth (ground) conductor should be the
last conductor to come loose from its terminal. Make sure that the earth (ground)
conductor is longer than the phase conductors. This applies to both ends of the motor
cable.
• Risk of electrical shock or burn. You must connect an additional earth- (ground-) fault
protection device to the earthed (grounded) connectors if persons are likely to come
into physical contact with the pump or pumped liquids.
Connect the motor cable to the pump
CAUTION:
Leakage into the electrical parts can cause damaged equipment or a blown fuse. Keep the
end of the motor cable above the liquid level.
1
2
1.
2.
Entrance cover
O-ring
For more information about the cable entry, see the Parts list.
1. Remove the entrance cover and the O-ring from the stator housing.
This provides access to the terminal board.
22
Flygt 3152 Installation, Operation, and Maintenance Manual
Installation
2. Check the data plate to see which connections are required for the power supply:
• Y
• D
• Y serial
• Y parallel
• Y/D
3. Arrange the connections on the terminal board in accordance with the required power
supply.
Links (jumper strips) are not used with the Y/D start.
4. Connect the mains leads (L1, L2, L3, and earth (ground)) according to applicable cable
chart.
The earth (ground) lead must be 50 mm ( 2.0 in.) longer than the phase leads in the
junction box of the unit.
5. Make sure that the pump is correctly connected to earth (ground).
6. Connect the control leads to the applicable terminal board.
7. Make sure that any thermal contacts incorporated in the pump are properly connected
to the terminal board.
8. Install the entrance cover and the O-ring on the stator housing.
9. Fasten the screws on the entrance flange so that the cable insertion assembly bottoms
out.
Connect the motor cable to the starter and monitoring equipment
WARNING:
Do not install the starter equipment in an explosive zone or in the sump.
NOTICE:
• Either thermal contacts or thermistors are incorporated in the pump.
• Thermal contacts must never be exposed to voltages higher than 250 V, breaking
current maximum 4 A. It is recommended that they are connected to 24 V over
separate fuses to protect other automatic equipment.
1. If thermal contacts are included in the pump installation, connect the T1 and T2 control
conductors to the MiniCAS II monitoring equipment.
Do not connect the T1 and T2 leads to thermal contacts if the temperature of the
pumped liquid is above 40В°C (104В°F).
NOTICE:
Ex-approved products must always have the thermal contacts connected irrespective
of the ambient temperature.
2. If thermistors are included in the pump installation, and screened or auxiliary cable is
used, then connect T1(1) and T2(2) to thermistor relay or MAS 711, and T3(3) and T4
(4) to MiniCAS II or MAS 711.
3. Connect the mains leads (L1, L2, L3, and earth [ground]) to the starter equipment.
For information about the phase sequence and the color codes of the leads, see Cable
charts (page 24).
4. Check the functionality of the monitoring equipment:
a) Check that the signals and the tripping function work properly.
b) Check that the relays, lamps, fuses, and connections are intact.
Replace any defective equipment.
Flygt 3152 Installation, Operation, and Maintenance Manual
23
Installation
Cable charts
2
1
2
3
4
5
6
1
7
2
L1 L2 L3
GC
3
1
L2
4
7
L1
L1
5
T16 T15 T2 T1
L3
L2
U1 W2 V1 U2 W1 V2
6
1.
2.
3.
4.
5.
6.
7.
Control leads
Starter equipment
Mains leads
Motor cable
Terminal blocks on pump
Stator leads
Control cable
Figure 8: Connection locations
Figure 9: Phase sequence
Colors and marking of the mains leads
Mains
SUBCAB 7GX
SUBCAB 4GX
SUBCAB AWG
L1
Black 1
Brown
Red
L2
Black 2
Black
Black
L3
Black 3
Grey
White
Yellow/Green
Yellow/Green
Yellow/Green
-
-
Yellow
Groundcheck (GC)
Color and marking of the control leads
Control
SUBCAB 7GX and SUBCAB 4GX
SUBCAB AWG
T1
White T1
Orange
T2
White T2
Blue
Colors of the stator leads
Stator connection
24
Lead color
U1
Red
U2
Green
U5
Red
V1
Brown
V2
Blue
Flygt 3152 Installation, Operation, and Maintenance Manual
L3
Installation
Stator connection
Lead color
V5
Brown
W1
Yellow
W2
Black
W5
Yellow
SUBCAB 7GX, 6 stator leads, D connection
This table shows the connection diagrams for the SUBCAB 7GX (3-phase power cables),
with D connection.
D connection
L1
L2
L3
T1 T2
1 4 2 5 3 6 T1
T2
SUBCAB
В®
SUBCAB В®
T1 T2
1
43
6
2
5
W2
U2
V2
U1
V1
W1
W2 U1
T1 T2
T1
T2
V1 U2 W1
V2
SUBCAB 7GX, 6 stator leads, Y/D connection
This table shows the connection diagrams for the SUBCAB 7GX (3-phase power cables),
with Y/D connection.
Flygt 3152 Installation, Operation, and Maintenance Manual
25
Installation
Y/D connection
3~
L1
L2
L3
L1
L2
L3
T1
T2
1
2
3
4
5
6
T1
T2
SUBCAB В®
1
2
3
4
5
6
T1 T2
U1
W2
V1
U2
W1
V2
V2
W1
U2
V1
U1 W2
SUBCAB 4GX/SUBCAB AWG, 6 stator leads, Y and D connections
This table shows the connection diagrams for the SUBCAB 4GX/SUBCAB AWG (3-phase
power cables), with Y and D connections.
Y connection
GC
D connection
T1 T2
L1 L2 L3
GC
L1 L2 L3
T1 T2
T1
T1
T2
T2
SUBCAB В®
T1 T2
T1 T2
SUBCAB В®
T1 T2
T1 T2
GC
GC
L1
L3
W2
SUBCAB В®
SUBCAB В®
L1
L3
L2
W2
U2
V2
U1
V1
W1
U1
V1
U2
W1 V2
T1
T2
L2
W2
U2
V2
U1
V1
W1
W2 U1
V1
U2
T1
T2
W1 V2
SUBCAB 4GX, 6 stator leads, Y/D connection
This table shows the connection diagrams for the SUBCAB 4GX (3-phase power cables),
with Y/D connection.
26
Flygt 3152 Installation, Operation, and Maintenance Manual
Installation
Y/D connection
L1 L2
L3
L1
L2 L3
1
3
4
5
6
T1
T2
SUBCAB В®
1
2
SUBCAB В®
3
2
SUBCAB
В®
2
T1 T2
4
5
6
3
5
6
4
T1 T2
T1 T2
1
W1
V1
U1
T1
V2
U2
W2
T2
U2
W1
U1
V1
V2
W2
SUBCAB 4GX/SUBCAB AWG, 9 stator leads, 230V
This table shows the connection diagrams for the SUBCAB 4GX/SUBCAB AWG (3-phase
power cable), with Y parallel connection (60 Hz only).
Y parallel connection
3~
GC
L1
L2 L3
T1 T2
T1 T2
SUBCAB В®
SUBCAB В®
GC
T2
T1
L1
L3
L2
W2
U2
V2 T1
U1
V1
W1
GC
W2 U5
U1
T2
W1
V1 U2
V2
V5
W5
SUBCAB 4GX/SUBCAB AWG, 9 stator leads, 460V
This table shows the connection diagram for the SUBCAB 4GX/SUBCAB AWG (3-phase
power cable), with Y serial connection (60 Hz only).
Flygt 3152 Installation, Operation, and Maintenance Manual
27
Installation
Y serial connection
3~
GC
L1
T1 T2
L2 L3
T1 T2
SUBCAB В®
SUBCAB
В®
GC
T2
T1
L1 L3
L2
W2
U2
V2
U1
V1
W1
GC
V2
U2 U1
U5
V1
V5
T1
T2
W1
W5
W2
SUBCAB Screened S3X2.5+3X2.5/3+4X1.5, 6 stator leads, Y and D connection
This table shows the connection diagrams for the SUBCAB Screened (3-phase power
cable), with Y parallel/serial connection (60 Hz only).
Y serial connection
D serial connection
L1 L2 L3 T1 T2
L1 L2 L3 T1 T2
1
2
3
T1 T2
T3
1
T4
2
3
1
T3
T4
T1 T2
1
3
28
W2
U2
V2
U1
V1
W1
U1 V1
T4
T3
T4
3
2
2
W2
T3
SUBCAB В®
SUBCAB В®
T1 T2
T1 T2
U2
V2
W1
T1
T2
W2
W2
U2
V2
U1
V1
W1
U1 V1
T1
T2
U2
V2
W1
Flygt 3152 Installation, Operation, and Maintenance Manual
Installation
Sensor-connection
Thermal contact
Thermistor (only standard version)
FLS and Thermal contact
Value
0 mA
7.8 mA
36 mA
Overtemperature
OK
Leakage
The values have a 10 % tolerance
CLS and Thermal contact (only standard version)
Value
0 mA
5.5mA
29mA
Overtemperature
OK
Leakage (5 second delay)
The values have a 10 % tolerance
CLS, FLS, and Thermal contact (only standard version)
Value
0 mA
13.3 mA
36-42mA
Overtemperature
OK
Leakage (0/5 seconds delay)
The values have a 10 % tolerance
Flygt 3152 Installation, Operation, and Maintenance Manual
29
Installation
Check the impeller rotation
WARNING:
The starting jerk can be powerful.
1. Start the motor.
2. Stop the motor after a few seconds.
3. Check that the impeller rotates according to this illustration.
The correct direction of impeller rotation is clockwise when you look at the pump from
above.
4. If the impeller rotates in the wrong direction, do one of these steps:
• If the motor has a 1-phase connection, contact the local Xylem shop.
• If the motor has a 3-phase connection, transpose two phase leads and do this
procedure again.
30
Flygt 3152 Installation, Operation, and Maintenance Manual
Operation
Operation
Distance to wet areas
Electrical Hazard:
Risk of electrical shock when pumping or mixing near a lake, jetties, beaches, ponds,
fountains, or similar. There must be a safety distance of at least 20 m (65 ft.) between the
person and the product if the person is in contact with the pumped or mixed liquid.
Start the pump
WARNING:
• If you need to work on the pump, make sure that it is isolated from the power supply and
cannot be energized.
• Make sure that the pump cannot roll or fall over and injure people or damage property.
• In some installations, the pump and the surrounding liquid may be hot. Bear in mind the
risk of burn injuries.
• Make sure nobody is close to the pump when it is started. The pump will jerk in the
opposite direction of the impeller rotation.
NOTICE:
Make sure that the rotation of the impeller is correct. For more information, see Check the
impeller rotation.
1. Check the oil level in the oil housing.
2. Remove the fuses or open the circuit breaker, and check that the impeller can be
rotated freely.
3. Conduct insulation test phase to ground. To pass, the value must exceed 5 megohms.
4. Check that the monitoring equipment works.
5. Start the pump.
Flygt 3152 Installation, Operation, and Maintenance Manual
31
Maintenance
Maintenance
Precautions
WARNING:
• Always follow safety guidelines when working on the pump. See Introduction and Safety
(page 3).
• Disconnect and lock out electrical power before installing or servicing the pump.
• Make sure that the pump cannot roll or fall over and injure people or damage property.
• Rinse the pump thoroughly with clean water before working on the pump.
• Rinse the components in water after dismantling.
Make sure that you follow these requirements:
• Check the explosion risk before you weld or use electrical hand tools.
• Allow all system and pump components to cool before you handle them.
• Make sure that the product and its components have been thoroughly cleaned.
• Do not open any vent or drain valves or remove any plugs while the system is
pressurized. Make sure that the pump is isolated from the system and that pressure is
relieved before you disassemble the pump, remove plugs, or disconnect piping.
Maintenance guidelines
During maintenance and before reassembly, always remember to perform these tasks:
• Clean all parts thoroughly, particularly O-ring grooves.
• Change all O-rings, gaskets, and seal washers.
• Lubricate all springs, screws, and O-rings with grease.
During reassembly, always make sure that existing index markings are in line.
The reassembled drive unit must always be insulation-tested and the reassembled pump
must always be test-run before normal operation.
Torque values
Screws and nuts
Stainless steel, A2
and A4, torque Nm
(ft-lbs)
1
32
Property M4
class
M5
M6
70 +80
5.4 (4)
9.3 (6.9) 22 (16)
2.7 (2)
M8
M10
M12
M16
M20
M24
M30
44 (32)
76 (56)
187
(138)
364
(268)
629
(464)
1240
(915)
Property class 70 is torque tightened as class 80.
Flygt 3152 Installation, Operation, and Maintenance Manual
Maintenance
Property M4
class
Carbon steel and
alloyed steel, torque
Nm (ft-lbs)
M5
M6
M8
M10
M12
M16
M20
M24
M30
8.8
2.9 (2.1) 5.7 (4.2) 9.8 (7.2) 24 (18)
47 (35)
81(60)
194
(143)
385
(285)
665
(490)
1310
(966)
10.9
4.0 (2.9) 8.1 (6)
33
(24.3)
65 (48)
114 (84) 277
(204)
541
(399)
935
(689)
1840
(1357)
12.9
4.9 (3.6) 9.7 (7.2) 17
(12.5)
40 (30)
79 (58)
136
(100)
649
(480)
1120
(825)
2210
(1630)
14
(10.3)
333
(245)
Screws with countersunk heads
Property
class
M4
M5
M6
M8
M10
M12
M16
M20
M24
Stainless steel, A2 and 70 +801
A4, torque Nm (ft-lbs)
1.2 (0.9)
2.7 (2)
5.4 (4)
9.3 (6.9)
22 (16)
44 (32)
76 (56)
120 (88)
187
(138)
Carbon steel and
alloyed steel, torque
Nm (ft-lbs)
8.8
2.3 (1.7)
4.6 (3.4)
7.8 (5.8)
19 (14)
38 (28)
65 (48)
158
(116)
308 (228) 532
(392)
10.9
3.2 (2.4)
6.5 (4.8)
11(8)
26 (19)
52 (38)
91 (67)
222
(164)
433 (320) 748
(552)
12.9
3.9 (2.9)
7.8 (5.8)
14 (10.3) 32 (23.6) 63 (46)
109 (80)
266
(196)
519 (383) 896
(661)
Change the oil
The following items are needed for this procedure:
• New oil plugs
• New O-rings
• Oil that should be a medical white oil of paraffin type that fulfills FDA 172.878 (a) and
viscosity close to VG32.
1. Place the pump in a horizontal position.
2. Turn the pump so that the oil hole faces downwards.
3. Unscrew the oil plug.
If the pump has a hole with the markings "oil out" it is important that this hole is used
for drainage.
WARNING:
The oil housing may be pressurized. Hold a rag over the oil plug to
prevent oil from spraying out.
Flygt 3152 Installation, Operation, and Maintenance Manual
33
Maintenance
1.
2.
Inspection plug
Oil plug
4. Drain the pump.
Unscrew the other oil plug for easier drainage.
5. Fill the housing with new oil.
Quantity: approximately 4.5 liters (4.76 US quarts)
6. Insert and tighten the new O-rings and plugs.
Tightening torque: 50 Nm (36.9 ft-lbs)
34
Flygt 3152 Installation, Operation, and Maintenance Manual
Maintenance
Replace the wear rings
Before replacing any wear ring, do the action applicable for your pump model:
• Disconnect and remove the drive unit end from the pump housing.
• Remove the lower diffuser.
When the clearance between the impeller wear ring (rotating) and pump housing wear
ring (stationary) exceeds 2mm (0.08in), one of the following wear rings must be replaced.
• the wear ring in the pump housing
• the impeller wear ring
1
2
3
1.
2.
3.
O-ring
Wear ring in the pump housing
Impeller wear ring
Figure 10: 3152 LT, MT, and HT
Figure 11: 3152 SH
Flygt 3152 Installation, Operation, and Maintenance Manual
35
Maintenance
1
1.
Lower diffuser
Figure 12: LL 3152
Replace the wear ring in the pump housing, diffuser ring, or suction cover
Figure 13: The wear ring in the pump housing
1. Knock off the wear ring using a hammer and a chisel.
If necessary, saw grooves in the wear ring using a hacksaw.
2. Please, check the surface intended for the wear ring that it is clean, before you are
mounting a new wear ring.
3. Drive in the new wear ring.
Use a rubber mallet or a wooden block to prevent deformation.
36
Flygt 3152 Installation, Operation, and Maintenance Manual
Maintenance
The work will proceed more easily if the pump housing , diffuser ring, or suction cover
first is heated and/or the wear ring cooled.
4. Before assembling the pump housing or diffuser ring with the drive unit end, check the
following:
• Check the O-ring and fit it in place.
• Check the orientation of the pump housing or diffuser ring.
5. Install the drive unit on the pump housing.
Tightening torque, see Torque values (page 32).
Replace the impeller wear ring
Figure 14: The impeller wear ring
1. Lay the drive unit on its side.
2. Knock off the impeller wear ring from the impeller.
If necessary, saw grooves in the wear ring using a hacksaw.
3. Heat the new impeller wear ring and press it onto the impeller.
4. Before assembling the pump housing or diffuser ring with the drive unit end, check the
following:
• Check the O-ring and fit it in place.
• Check the orientation of the pump housing or diffuser ring.
5. Install the drive unit on the pump housing.
Tightening torque, see Torque values (page 32).
Flygt 3152 Installation, Operation, and Maintenance Manual
37
Maintenance
Replace the impeller
1
2
3
1.
2.
3.
O-ring
Wear ring in the pump casing
Impeller wear ring
Figure 15: 3152 LT, MT, and HT
1
2
4
3
5
6
1.
2.
3.
4.
5.
6.
Upper wear protection
O-ring
Lower wear protection
Lock nuts
Sleeve screws
Cap nuts
Figure 16: HS 3152
38
Flygt 3152 Installation, Operation, and Maintenance Manual
Maintenance
1
1.
Lower diffuser
Figure 17: LL 3152
Figure 18: PL 3152
Flygt 3152 Installation, Operation, and Maintenance Manual
39
WS000656A
Maintenance
Figure 19: F 3152
Required tools for F 3152:
• 18 mm socket
• Impeller puller
If applicable, contact your local Xylem representative for correct type and size.
• Rod (wood or plastic) for locking the impeller in place, if applicable.
• Two crowbars, if applicable
WARNING:
• If you fail with the impeller installation, you must redo the installation procedure from the
beginning.
• A worn impeller and/or pump housing can have very sharp edges. Wear protective
gloves.
• When laying the pump on its side, do not allow the weight of the pump to rest on any
portion of the impeller. The impeller must not be allowed to make contact with the
concrete floor or other hard and rough surfaces.
Remove the impeller and the wear protections
For the HS-version, also remove the wear protections.
1. Disconnect and remove the drive unit end from the pump housing.
For lift models, remove the lower diffuser instead.
2. Lay the drive unit end on its side.
3. Remove the impeller screw or nut.
40
Flygt 3152 Installation, Operation, and Maintenance Manual
Maintenance
4. Depending the pumps model, do the following.
If the
pump
model is
a...
Then...
HSversion
1.
2.
3.
4.
Remove the washer.
Remove the impeller using a impeller puller for HS-versions.
Remove the upper wear protection.
Unscrew the four cap nuts and withdraw the lower wear protection from the pump
housing.
Other
version
1.
2.
Remove the impeller, impeller hub, or propeller using a impeller hub.
For PL3152, use an M16 threaded rod, length minimum 400 mm (15.7 in) and two
M16 nuts to contra fit them at the one end of the rod used as a puller screw.
NOTICE:
Do not pry off the impeller or the impeller hub since it can easily be damaged.
Install the impeller and the wear protections
For the HS-version, also install the wear protections.
1. Prepare the shaft:
a) Make sure that the end of the shaft is clean and free from burrs.
Polish off any flaws with a fine emery cloth.
b) Make sure that the key is seated in the keyway on the shaft.
c) Grease the end of the shaft.
2. Mount the impeller, impeller hub, or propeller.
a) Fit the upper wear protection, HS-version only.
b) Grease the impeller hub.
Flygt 3152 Installation, Operation, and Maintenance Manual
41
Maintenance
c) Place the washer on the impeller or propeller screw.
d) Press the impeller, impeller hub, or propeller onto the shaft with the impeller or
propeller screw.
3. Fasten the impeller, impeller hub, or propeller.
a) Tighten the impeller or propeller screw.
Tightening torque, see Torque values (page 32)
4.
5.
6.
7.
b) If the pump is a HS-version, unscrew the sleeve screws.
c) If the pump is a HS-version, fit the lower wear protection in the pump housing.
Check that the impeller is firmly seated and can be easily rotated by hand.
Before assembling the pump housing and the drive unit end, check the following:
Not applicable for PL-version.
a) Check the O-ring and fit it in place.
b) Check the orientation of the pump housing.
If the pump is a PL-version, do the following.
a) Fit the hood.
b) Fit the drive unit end to the diffuser.
If the pump is another version, assemble the pump.
Tightening torque, see Torque values (page 32).
More extensive repairs require special tools and should be completed by an Xylem
authorized service technician.
Adjust the lower wear protection
For the HS version, the lower wear protection may need adjustment. The clearance
between the impeller and the wear protection should be minimal. The clearance is
adjusted with the sleeve screws.
1. Check that the impeller can easily be rotated by hand.
2. Tighten the sleeve screws evenly until the wear protection is flush against the impeller.
3. Back off the sleeve screws a quarter turn.
4. Tighten the lock nuts evenly all around.
5. Fit and tighten the cap nuts.
6. Check that the impeller can easily be rotated by hand.
For the pump to perform at maximum capacity, the impeller must be adjusted regularly.
More extensive repairs require special tools and should be carried out by an Xylem
authorized service technician.
Remove the impeller: F
1. Place the pump in a horizontal position.
2. Remove the impeller screw and washer.
If applicable, use the rod.
42
Flygt 3152 Installation, Operation, and Maintenance Manual
WS000645A
Maintenance
3. Remove the impeller.
Use the impeller puller or the crowbar.
Install the impeller: F
WS000645A
1. Prepare the shaft:
a) Make sure that the end of the shaft is clean and free from burrs.
Polish off any flaws with a fine emery cloth.
b) Make sure that the key is seated in the keyway on the shaft.
c) Grease the end of the shaft.
2. Mount the impeller:
a) Place the washers on the shaft.
b) Fit the impeller.
If applicable, use the rod.
Tightening torque: 40 Nm (30 ft-lbs).
Check that the impeller can rotate freely.
3. Adjust the impeller:
a) Measure the distance between the edge of the impeller and the pump housing
cover.
The correct distance should be 0.2–0.6 mm (0.008-0.02 in.). Add or remove the
appropriate number of washers in order to achieve correct distance.
Flygt 3152 Installation, Operation, and Maintenance Manual
43
WS000650A
Maintenance
WS000651A
b) Fit the impeller.
If applicable, use the rod.
Tightening torque: 40 Nm (30 ft-lbs).
Check that the impeller can rotate freely.
4. Mount the suction cover:
a) Fit adjustment washers onto the studs on the pump housing.
b) Fit the suction cover to the studs.
c) Fit one adjustment washer and a lock nut onto each stud.
d) Tighten the studs.
Tightening torque: 57 Nm (42 ft-lbs).
5. Adjust the suction cover:
a) Measure the distance between the edge of the impeller and the pump housing
cover.
The correct distance should be 0.2–0.6 mm (0.008-0.02 in.). Add or remove the
appropriate number of washers in order to achieve correct distance.
44
Flygt 3152 Installation, Operation, and Maintenance Manual
WS000653A
Maintenance
b) Measure the distance between the edge of the impeller and the pump housing
cover.
Tightening torque: 57 Nm (42 ft-lbs).
Check that the impeller can rotate freely.
More extensive repairs require special tools and should be completed by an Xylem
authorized service technician.
Service the pump
Type of service
Purpose
Inspection interval
Initial inspection
To make a check up of the pump
condition by an authorized Xylem
service representative and, based
on the result and findings from
these measures, to determine the
intervals for periodical inspection
and major overhaul for the specific
installation.
Within the first year of operation.
Periodical inspection
To prevent operational interruptions
and machine breakdown. Measures
to secure performance and pump
efficiency are defined and decided
for each individual application. It
can include such things as impeller
trimming, wear part control and
replacement, control of zinc-anodes
and control of the stator.
Up to 12,000 hours or 3 year,
whichever comes first.
Applies to normal applications and
operating conditions at media
(liquid) temperatures <40В°C.
Major overhaul
To secure a long operating lifetime
for the product. It includes
replacement of key components
and the measures taken during an
inspection.
Up to 24,000 hours or 6 years,
whichever comes first.
Applies to normal applications and
operating conditions at media
(liquid) temperatures <40В°C.
NOTICE:
Shorter intervals may be required when the operating conditions are extreme, for example
with very abrasive or corrosive applications or when the liquid temperatures exceed 40В°C
(104В°F).
Flygt 3152 Installation, Operation, and Maintenance Manual
45
Maintenance
Inspection
Service item
Cable
2
46
Action
1.
2.
If the outer jacket is damaged, replace the cable.
Check that the cables do not have any sharp bends and are not
pinched.
Connection to power
Check that the connections are properly tightened.
Electrical cabinets
Check that they are clean and dry.
Impeller
1.
2.
Check the impeller clearance.
Adjust the impeller, if necessary.
Stator housing
1.
2.
Drain all liquid, if any.
Check the resistance of the leakage sensor.
Normal value approx.1500 ohms, alarm approx. 430 ohms.
Insulation
Use a megger maximum 1000 V.
1. Check that the resistance between the earth (ground) and
phase lead is more than 5 megohms.
2. Conduct a phase-to-phase resistance check.
Junction box
Check that it is clean and dry.
Level regulators
Check the condition and functionality.
Lifting device
Check that local safety regulations are followed.
Lifting handle
1.
2.
3.
Check the screws.
Check the condition of the lifting handle.
Replace if necessary.
O-rings
1.
2.
3.
Replace the oil plug O-rings.
Replace the O-rings at the entrance or junction cover.
Grease the new O-rings.
Overload protection and other
protections
Check the correct settings.
Personnel safety devices
Check the guard rails, covers, and other protections.
Rotation direction
Check the impeller rotation.
Oil housing2
Fill with new oil, if necessary.
Terminal board
Check that the connections are properly tightened.
Thermal contacts
Normally closed circuit; interval 0–1 ohm.
Thermistor
Check the resistance is between 20–250 ohms and the measured
voltage is maximum 2 V DC.
Voltage and amperage
Check the running values.
Regardless of individual applications, the stator housing and the oil housing should not be inspected less frequently than the intervals for
normal applications and operating conditions at media (liquid) temperatures <40В°C.
Flygt 3152 Installation, Operation, and Maintenance Manual
Maintenance
Major overhaul
For a major overhaul, take this action in addition to the tasks listed under Inspection.
Service item
Action
Support and main bearing
Replace the bearings with new bearings.
Mechanical seal
Replace with new seal units.
Service in case of alarm
Alarm source
Action
The thermistor/Thermal contact
Check that the cooling jacket is not clogged. Clean if necessary.
The overload protection
Check that the impeller can rotate freely.
Flygt 3152 Installation, Operation, and Maintenance Manual
47
Troubleshooting
Troubleshooting
Introduction
Follow these guidelines when troubleshooting the pump:
• Disconnect and lock out the power supply except when conducting checks that
require voltage.
• Make sure that no one is near the pump when the power supply is reconnected.
• When troubleshooting electrical equipment, use the following:
• Universal instrument multimeter
• Test lamp (continuity tester)
• Wiring diagram
The pump does not start
WARNING:
Always disconnect and lock out power before servicing to prevent unexpected startup.
Failure to do so could result in death or serious injury.
NOTICE:
Do NOT override the motor protection repeatedly if it has tripped. Doing so may result in
equipment damage.
48
Cause
Remedy
An alarm signal has been triggered
on the control panel.
Check that:
• The impeller rotates freely.
• The sensor indicators do not indicate an alarm.
• The overload protection is not tripped.
If the problem still persists:
Contact the local Xylem service shop.
The pump does not start
automatically, but can be started
manually.
Check that:
• The start level regulator is functioning. Clean or replace if necessary.
• All connections are intact.
• The relay and contactor coils are intact.
• The control switch (Man/Auto) makes contact in both positions.
Check the control circuit and functions.
The installation is not receiving
voltage.
Check that:
• The main power switch is on.
• There is control voltage to the start equipment.
• The fuses are intact.
• There is voltage in all phases of the supply line.
• All fuses have power and that they are securely fastened to the fuse
holders.
• The overload protection is not tripped.
• The motor cable is not damaged.
The impeller is stuck.
Clean:
Flygt 3152 Installation, Operation, and Maintenance Manual
Troubleshooting
Cause
Remedy
• The impeller
• The sump in order to prevent the impeller from clogging again.
If the problem persists, refer to the Flygt Service Guide on the web or contact the local
Xylem service shop. Always state the serial number of your pump when you contact Xylem,
see Product Description (page 11).
The pump does not stop when a level sensor is used
WARNING:
Always disconnect and lock out power before servicing to prevent unexpected startup.
Failure to do so could result in death or serious injury.
Cause
Remedy
The pump is unable to empty the
sump to the stop level.
Check that:
• There are no leaks from the piping and/or discharge connection.
• The impeller is not clogged.
• The non-return valve(s) are functioning properly.
• The pump has adequate capacity. For information:
Contact the local Xylem service shop.
There is a malfunction in the levelsensing equipment.
•
•
•
•
The stop level is set too low.
Raise the stop level.
Clean the level regulators.
Check the functioning of the level regulators.
Check the contactor and the control circuit.
Replace all defective items.
If the problem persists, refer to the Flygt Service Guide on the web or contact the local
Xylem service shop. Always state the serial number of your pump when you contact Xylem,
see Product Description (page 11).
The pump starts-stops-starts in rapid sequence
Cause
Remedy
The pump starts due to back-flow
which fills the sump to the start
level again.
Check that:
• The distance between the start and stop levels is sufficient.
• The non-return valve(s) work(s) properly.
• The length of the discharge pipe between the pump and the first nonreturn valve is sufficiently short.
The self-holding function of the
contactor malfunctions.
Check:
• The contactor connections.
• The voltage in the control circuit in relation to the rated voltages on the
coil.
• The functioning of the stop-level regulator.
• Whether the voltage drop in the line at the starting surge causes the
contactor's self-holding malfunction.
Flygt 3152 Installation, Operation, and Maintenance Manual
49
Troubleshooting
If the problem persists, refer to the Flygt Service Guide on the web or contact the local
Xylem service shop. Always state the serial number of your pump when you contact Xylem,
see Product Description (page 11).
The pump runs but the motor protection trips
WARNING:
Always disconnect and lock out power before servicing to prevent unexpected startup.
Failure to do so could result in death or serious injury.
NOTICE:
Do NOT override the motor protection repeatedly if it has tripped. Doing so may result in
equipment damage.
Cause
Remedy
The motor protection is set too low.
Set the motor protection according to the data plate and if applicable the
cable chart.
The impeller is difficult to rotate by
hand.
• Clean the impeller.
• Clean out the sump.
• Check that the impeller is properly trimmed.
The drive unit is not receiving full
voltage on all three phases.
• Check the fuses. Replace fuses that have tripped.
• If the fuses are intact, notify a certified electrician.
The phase currents vary, or they are
too high.
Contact the local Xylem service shop.
The insulation between the phases
and ground in the stator is
defective.
1.
2.
Use an insulation tester. With a 1000 V DC megger, check that the
insulation between the phases and between any phase and ground is
> 5 megohms.
If the insulation is less:
Contact the local Xylem service shop.
The density of the pumped fluid is
too high.
Make sure that the maximum density is 1100 kg/m3 (9.2 lb/US gal)
• Change the impeller, or
• Change to a more suitable pump.
• Contact the local Xylem service shop.
There is a malfunction in the
overload protection.
Replace the overload protection.
If the problem persists, refer to the Flygt Service Guide on the web or contact the local
Xylem service shop. Always state the serial number of your pump when you contact Xylem,
see Product Description (page 11).
The pump delivers too little or no water
WARNING:
Always disconnect and lock out power before servicing to prevent unexpected startup.
Failure to do so could result in death or serious injury.
50
Flygt 3152 Installation, Operation, and Maintenance Manual
Troubleshooting
NOTICE:
Do NOT override the motor protection repeatedly if it has tripped. Doing so may result in
equipment damage.
Cause
Remedy
The impeller rotates in the wrong
direction.
• If it is a 3-phase pump, transpose two phase leads.
• If it is a 1-phase pump:
Contact the local Xylem service shop.
One or more of the valves are set in
the wrong positions.
•
•
•
•
The impeller is difficult to rotate by
hand.
• Clean the impeller.
• Clean out the sump.
• Check that the impeller is properly trimmed.
The pipes are obstructed.
Clean out the pipes to ensure a free flow.
The pipes and joints leak.
Find the leaks and seal them.
There are signs of wear on the
impeller, pump, and casing.
Replace the worn parts.
The liquid level is too low.
• Check that the level sensor is set correctly.
• Depending on the installation type, add a means for priming the pump,
such as a foot valve.
Reset the valves that are set in the wrong position.
Replace the valves, if necessary.
Check that all valves are correctly installed according to media flow.
Check that all valves open correctly.
If the problem persists, refer to the Flygt Service Guide on the web or contact the local
Xylem service shop. Always state the serial number of your pump when you contact Xylem,
see Product Description (page 11).
Flygt 3152 Installation, Operation, and Maintenance Manual
51
Technical Reference
Technical Reference
Application limits
Data
Description
Liquid temperature
40В°C (104В°F) maximum
If the pump is not equipped with cooling jacket, the pump can be operated at full
load only if at least half the stator housing is submerged.
Warm-liquid version: 90В°C (195В°F) maximum
At increased temperatures, the pump must be completely submerged when
operating at full load.
Ex-approved pumps: 40В°C (104В°F) maximum
Liquid density
1100 kg/mВі (9.2 lb per US gal) maximum
pH of the pumped media
(liquid)
5.5–14 for cast iron pumps
3–14 for stainless steel pumps
Depth of immersion
20 m (65 ft) maximum
Other
For the specific weight, current, voltage, power ratings, and speed of the pump, see
the data plate of the pump.
Motor data
52
Feature
Description
Motor type
Squirrel-cage induction motor
Frequency
50 or 60 Hz
Supply
1-phase or 3-phase
Starting method
• Direct on-line
• Star-delta
Maximum starts per
hour
30 evenly spaced starts per hour
Code compliance
IEC 60034-1
Rated output variation
В±5%
Voltage variation without
overheating
В±10%, provided that it does not run continuously at full load
Voltage imbalance
tolerance
2%
Stator insulation class
H (180В°C [360В°F])
Flygt 3152 Installation, Operation, and Maintenance Manual
Xylem |’zīləm|
1) The tissue in plants that brings water upward from the roots
2) A leading global water technology company
We're 12,000 people unified in a common purpose: creating
innovative solutions to meet our world's water needs. Developing new
technologies that will improve the way water is used, conserved, and
re-used in the future is central to our work. We move, treat, analyze,
and return water to the environment, and we help people use water
efficiently, in their homes, buildings, factories and farms. In more than
150 countries, we have strong, long-standing relationships with
customers who know us for our powerful combination of leading
product brands and applications expertise, backed by a legacy of
innovation.
For more information on how Xylem can help you, go to xyleminc.com
Xylem Water Solutions AB
Gesällvägen 33
174 87 Sundbyberg
Sweden
Tel. +46-8-475 60 00
Fax +46-8-475 69 00
http://tpi.xyleminc.com
Visit our Web site for the latest version of this document and
more information
The original instruction is in English. All non-English
instructions are translations of the original instruction.
В©
2011 Xylem Inc
898073_3.0_en.US_2010-10_IOM.3152.091/.181/.350_XR
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement