ZN-NH11VNE Manual - Ganz Security

ZN-NH11VNE Manual - Ganz Security
ZC-Y11VE/ZN-NH11VE/ZN-NHW11VE Installation Guide
INFORMATION TO USER
CAUTION
RISK OF ELECTRIC SHOCK,
DO NOT OPEN
!
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SEERIVCE PERSONEL.
This symbol is intended to alert the user to the presence of un-insulated
“dangerous voltage” within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
!
This symbol is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
2010/2-1 03A.02
2
ZC-Y11VE/ZN-NH11VE/ZN-NHW11VE Installation Guide
Table of Contents
1. FEATURES ................................................................................................................. 5
2. PACKAGE CONTENTS ................................................................................................ 6
3. PART NAMES ............................................................................................................ 7
3.1. Rear View ....................................................................................................................... 7
3.2. Bottom View .................................................................................................................. 7
4. INSTALLATION ........................................................................................................ 10
4.1. Installing a C/CS Mounting lens .................................................................................... 10
4.2. Installing an Auto IRIS lens ............................................................................................ 10
4.3. Setting the Image Attribute .......................................................................................... 11
4.4. Operating the OSD Menu ............................................................................................. 11
5. CONNECTIONS ........................................................................................................ 12
5.1.Connectors .................................................................................................................... 13
6. CONFIGURATION .................................................................................................... 16
6.1.Set up network environment ......................................................................................... 16
6.2. View video on web page ............................................................................................... 16
6.2.1. View video using ZNS-GIT I IPAdminTool ................................................................ 16
6.2.2. View video using IP address ................................................................................... 19
6.3. Reset ............................................................................................................................ 19
6.4. Factory Default ............................................................................................................. 19
APPENDIX (A): SPECIFICATIONS.................................................................................. 20
Summary ............................................................................................................................ 20
Electrical Characteristics ..................................................................................................... 21
Environment Condition ....................................................................................................... 21
VCA (Video Content Analysis) .............................................................................................. 21
APPENDIX (B): POWER OVER ETHERNET .................................................................... 23
PoE compatibility ................................................................................................................ 23
Power classification............................................................................................................. 23
APPENDIX (C): DIMENSIONS ....................................................................................... 24
APPENDIX (D): ACCESSORIES ........... г‚Ёгѓ©гѓј! гѓ–гѓѓг‚Їгѓћгѓјг‚ЇгЃЊе®љзѕ©гЃ•г‚ЊгЃ¦гЃ„гЃѕгЃ›г‚“гЂ‚
APPENDIX (E): TROUBLE SHOOTING ........................................................................... 25
Checking your Firmware...................................................................................................... 25
2010/2-1 03A.02
3
ZC-Y11VE/ZN-NH11VE/ZN-NHW11VE Installation Guide
Support ............................................................................................................................... 25
2010/2-1 03A.02
4
ZC-Y11VE/ZN-NH11VE/ZN-NHW11VE Installation Guide
1. FEATURES
Camera
п‚·
п‚·
п‚·
Box type IP Camera
Sony 1/3” Super HAD CCD & High Quality SS-HQ1 Full Kit Chip Set
Sony 1/3" Vertical Double Density Color CCD (Optional)
True Day / Night (ICR) and WDR (Optional)
Streaming
п‚·
п‚·
п‚·
п‚·
Dual streaming mode (such as different codec/resolution/bit rate and so on.)
De-interlacing on DSP
Burnt-in text supported
Unicast/Multicast supported
Video/Audio
п‚·
п‚·
п‚·
п‚·
п‚·
Video compression: H.264/MPEG/MJPEG, 25/[email protected](PAL/NTSC)
Audio compression: G.711(ВµLaw, aLaw)/PCM
Analog video out for external monitors
Video Motion Detection supported
2-way mono audio supported
Network
п‚·
п‚·
RTSP/ HTTP protocol supported
10/100 Base-T Ethernet
Additional Features
п‚·
п‚·
п‚·
п‚·
п‚·
п‚·
п‚·
RS-485 supported
USB 2.0 supported (External storage, Wireless LAN)
Micro SD card supported
PoE supported
Built-in Video Content Analysis
OSD supported
SDK (Software Development Kit) provided
VCA (Video Content Analysis)
п‚·
п‚·
VCA Presence (Included as basic)
VCA Surveillance (Optional)
2010/2-1 03A.02
5
ZC-Y11VE/ZN-NH11VE/ZN-NHW11VE Installation Guide
2. PACKAGE CONTENTS
Unpack carefully and handle the equipment with care. The packaging contains:
ZN-Y11VE/ZN-NH11VE/ZN-NHW11VE
DC power adaptor
Mount ring
9 Pin terminal block
Rubber cap (for protecting CCD)
Hex wrench driver
Adaptor for mounting the camera
Screws
Quick Installation Guide
DC Jack Adaptor Cable
i
The above contents are subject to change without prior notice.
Note
2010/2-1 03A.02
6
ZC-Y11VE/ZN-NH11VE/ZN-NHW11VE Installation Guide
3. PART NAMES
3.1. Rear View
в—‹
1
в—‹
2
в—‹
3
в‘ LOOP OUT
RESET
DI
RS-485 DO
в—‹
4
в‘ AUDIO
в—‹
5
- +
C 1
C 1
Out In
Micro SD
в—‹
6
ETHERNET
в—‹
7
в—‹
8
3.2. Bottom View
в—‹
9
2010/2-1 03A.02
7
ZC-Y11VE/ZN-NH11VE/ZN-NHW11VE Installation Guide
в‘ Analog video out
It is an analog video output port.
в‘Ў Reset
Reset switch is used for restarting ZN-Y11VE/ZN-NH11VE/ZN-NHW11VE or resetting ZNY11VE/ZN-NH11VE/ZN-NHW11VE as Factory Default (FD). Refer to the section “6.3. Reset” for
more specific information.
в‘ў USB connector
Insert a USB storage device or Wi-Fi devices. (Only Ralink RT73 chipsets based wireless devices
are available.)
в‘Ј 9 pin terminal block for D/I, D/O, audio, and serial communication
Refer to the section “5.1.Connectors” for more specific information.
⑤ Power Adaptor Connector (DC 12V)
ZN-Y11VE/ZN-NH11VE/ZN-NHW11VE needs a DC12V for power supply. Refer to the section
“Power Adaptor Connector (DC 12V)” for more specific information.
+ -
!
Make sure the polarity is correct. Incorrect connection may cause malfunction
Caution or damage to the IP device.
в‘Ґ Micro SD Card socket
It is a memory card slot for external storage.
⑦ LAN Connector (Ethernet)
This is a RJ45 LAN connector for 10/100 Base-T Ethernet.
Status LED Network LED
2010/2-1 03A.02
8
ZC-Y11VE/ZN-NH11VE/ZN-NHW11VE Installation Guide
⑧ 4 Pin connector for Auto IRIS
Only DC-drive type is supported. Refer to the section “4.2. Installing an Auto IRIS lens” for
more specific information.
в‘Ё Adaptor for mounting the camera
Mounting points adaptor is provided on the bottom (or the top) of the camera for mounting
the camera on a bracket or tripod.
2010/2-1 03A.02
9
ZC-Y11VE/ZN-NH11VE/ZN-NHW11VE Installation Guide
4. INSTALLATION
CCW
CW
CW
SET Screw
SCREW
Set
(For IRIS LENS)
4.1. Installing a C/CS Mounting lens
1. Remove the protective rubber cap from the front of the camera.
2. Install the mount ring for lens and adjust the mount ring to fit C or CS lens.
3. Tighten the setscrews using the hex wrench in the package.
4.2. Installing an Auto IRIS lens
1. Remove the cover of the auto iris lens plug and connect it with the lens cable.
2. Connect the auto iris lens plug to the 4-pin lens terminal on the back of the camera.
i
Note
i
Use the connection recommended by the manufacturer. For best
performance, read the lens manual carefully. You may need to set the flange
back focus.
Only DC-drive type is supported.
Note
2010/2-1 03A.02
10
ZC-Y11VE/ZN-NH11VE/ZN-NHW11VE Installation Guide
2 1
4 3
4 pin connector for IRIS
PIN
1
2
3
4
DC IRIS Lens
DampDamp+
Drive+_
Drive-
4.3. Setting the Image Attribute
You can set the image attribute of camera through the webpage.
The menu of image attribute can be seen under Setup > Video & Audio > Video-in > Attribute
Setting. Brightness, contrast, hue, saturation and sharpness can be adjusted.
4.4. Operating the OSD Menu
To operate the OSD of camera, refer to the �OSD Menu Control Manual’ in the SDK.
2010/2-1 03A.02
11
ZC-Y11VE/ZN-NH11VE/ZN-NHW11VE Installation Guide
5. CONNECTIONS
Analog Video Out
LOOP OUT
DC Jack Adaptor
Cabl
RESET
RS-485 DO
- +
C 1
DI
C 1
AUDIO
Out In
Micro SD
Power Adaptor
LAN Cable
ETHERNET
4 pin connector for iris
!
When connecting the DC power supply, make sure the polarity is correct. Incorrect
Caution connection may cause malfunction or damage to the camera.
2010/2-1 03A.02
12
ZC-Y11VE/ZN-NH11VE/ZN-NHW11VE Installation Guide
5.1.Connectors
в‘ 9 pin terminal block
LOOP OUT
RESET
RS-485
- +
DO
DI
AUDIO
C 1 C 1
Out In
Micro SD
ETHERNET
в‘Ў RS-485
The RS-485 serial port consists of TRX+(RX+) and TRX-(RX-) as following the following image.
<RS-485 Application>
TRX+(RX+)
TRX-(RX-)
TX+
TX-
485
PTZDevices
Device
+
-
RS-485 Connection
в‘ў Sensor (DI) connection
ZN-Y11VE/ZN-NH11VE/ZN-NHW11VE provides 1 channel D/I. It can be connected to either a
voltage type sensor or a relay type sensor as the following figures. It can be selected by
software.
Input voltage range: 0 VDC minimum to 24 VDC maximum
Input voltage threshold: 1 V
!
Do not exceed the maximum input voltage or relay rate.
Caution
2010/2-1 03A.02
13
ZC-Y11VE/ZN-NH11VE/ZN-NHW11VE Installation Guide
Internal
+5V
Internal
DI
Output of
Sensor
+
DI 1
-
COM
COM
Relay Type
Output of
Sensor
+
-
-
+
Voltage Type
в‘Ј Alarm (DO) connection
Only the relay type is supported.
Relay Rating: Max 24VAC 500mA or 12VDC 1A
!
Do not exceed the maximum relay rating.
Caution
Internal
Device
DO
COM
Relay Type
⑤ Audio connection
ZN-Y11VE/ZN-NH11VE/ZN-NHW11VE has a mono audio input and a mono audio output. As the
output power for the audio is low, amplifier speaker is needed. (Do not use a headphone or
earphone directly to the camera.)
Aout
Ain
2010/2-1 03A.02
Speaker
Mic
14
ZC-Y11VE/ZN-NH11VE/ZN-NHW11VE Installation Guide
в‘Ґ Power Adaptor Connector (DC 12V)
Power adaptor connector connects to DC Jack adapter cable.
+
+
-
-
RED
!
Make sure the polarity is correct. Incorrect connection may cause malfunction or
damage to the IP device
Caution
!
Power Adaptor Connector (DC 12V)
Caution
2010/2-1 03A.02
15
ZC-Y11VE/ZN-NH11VE/ZN-NHW11VE Installation Guide
6. CONFIGURATION
6.1.Set up network environment
The default IP address of your IP device is 192.168.XXX.XXX. You can find the available IP address
from the MAC address of your device. Please make sure the device and your PC are on the same
network segment before running the installation. If the network segment between your PC and
the device is different, change your PC’s settings as below.
IP address : 192.168.xxx.xxx
Subnet mask: 255.255.0.0
6.2. View video on web page
View the live video on a web page using your IP device and its IP address. You can use the ZNSGIT I IPAdminTool or enter the IP address on the web page.
6.2.1. View video using ZNS-GIT I IPAdminTool
ZNS-GIT IPAdmin Tool automatically searches all activated GANZ Encoders and network
cameras and shows the product name, IP address, MAC address and etc. ZNS-GIT IPAdminTool
is provided with SDK at the following SDK path.
{SDK root}\BIN\TOOLS\AdminTool\
2010/2-1 03A.02
16
ZC-Y11VE/ZN-NH11VE/ZN-NHW11VE Installation Guide
To use the ZNS-GIT IPAdminTool and view the live video on a web page:
1. Start ZNS-GIT IPAdminTool. Names and info of currently activated devices appear as a
list.
2. Right-click on the desired device and select Web view.
3. Select Continue to this website on the Security Certificate Alert page.
(The explanation and captured images at this manual are mainly on the basis of Internet
Explorer 7.0)
4. Click pop-up blocked and install the ActiveX control as below. You need to install the
ActiveX for displaying the images.
2010/2-1 03A.02
17
ZC-Y11VE/ZN-NH11VE/ZN-NHW11VE Installation Guide
5. Wait for a few seconds while the web page loads. The live video is displayed as below.
6. If the live video is not displayed and “Can not Create XMLDOMDocument Install
MSXML4.0” message is shown as below, please download and Install from the link
below.
http://www.microsoft.com/downloads/details.aspx?familyid=3144B72B-B4F2-46DAB4B6-C5D7485F2B42&displaylang=en
(VCA Library requires MS XML 4.0 library which is an xml parser made by Microsoft.)
2010/2-1 03A.02
18
ZC-Y11VE/ZN-NH11VE/ZN-NHW11VE Installation Guide
6.2.2. View video using IP address
View the live video on a web page using your IP device and its IP address. To have the correct
IP address ready and use it on a web page:
1. Convert a MAC address to an IP address or check the IP address on the ZNS-GIT I
IPAdminTool.
(The MAC address is attached on the side or bottom of the device.)
MAC address = 00-1C-B8-C0-14-B1 в†’ IP address = 192.168.20.177
Convert the Hexadecimal number to Decimal number.
2. Open a web browser and enter the IP address of the device.
3. Click Continue to this website on the Security Certificate Alert page.
4. Click pop-up blocked and install the ActiveX control. You need to install the ActiveX for
displaying the images.
5. Wait for a few seconds while the web page loads. The live video is displayed.
6.3. Reset
1. While the device is in use, press and hold the Reset .
2. Release the Reset button after 3 seconds.
3. Wait for the system to reboot.
6.4. Factory Default
1.
2.
3.
4.
Disconnect the power supply from the device.
Connect the power to the device with the Reset button pressed and held.
Release the Reset button after 5 seconds.
Wait for the system to reboot.
The factory default settings can be inferred as follows:
IP address:
Network mask:
Gateway:
User ID:
Password:
2010/2-1 03A.02
192.168.xx.yy
255.255.0.0
192.168.0.1
root
pass
19
ZC-Y11VE/ZN-NH11VE/ZN-NHW11VE Installation Guide
APPENDIX (A): SPECIFICATIONS
Summary
Camera Module
Model
Image
Sensor
Effective
Pixels
Size
Scanning
system
CCD
Sync
Frequency
ELECTRICAL
ZN-Y11VE /ZN-NH11VE
ZN-NHW11VE
Sony 1/3” Super HAD CCD,
SONY 1/3" Vertical Double
410K Pixel
Density Color CCD
NTSC: 768(H) x 494(V)
PAL: 752(H) x 582(V)
1/3 inch interline transfer CCD
2:1 Interlace
NTSC: 15.734 KHz (H) 59.94 Hz(V)
PAL:15.625 KHz(H) 50.00 Hz (V)
Resolution
540 TV Lines
560 TV lines (Color),
600 TV lines (B/W)
S/N (Y
signal)
50dB (AGC Off)
52dB (AGC Off)
Min.
Illumination
0.3Lux/F1.2(Color),
01.Lux/F1.2(B/W), 0.002Lux
(Sens-up)
0.3Lux/F1.2(Color),
0.03Lux/F1.2(B/W)
Not supported
52dB(x128)
Wide
Dynamic
Range
Color
AGC Control
White
Balance
Electronic
Shutter
Speed
Sens-Up
DNR
Lens
Day & Night
ON/AUTO
OFF/LOW/MIDDLE/HIGH Selectable
ATW/AWC/MANUAL (1,800В° K~10,500В° K)
AUTO/
MANUAL
AUTO/
(NTSC: X256~1/60sec~
MANUAL
1/120,000sec,
(NTSC: 1/60~1/120,000,
PAL: X256~1/50sec~
PAL: 1/50~1/120,000)
1/120,000sec)
Sens-up and Sens-up Limit is
selectable / Flickerless
OFF/AUTO
OFF/LOW/MIDDLE/HIGH
ON (Level 0~32) /
(Noise Reduction)
OFF Selectable
3~8 mm Day & Night Vari-focal Auto Iris (Optional)
ZN-Y11VE: S/W
ZN-NH11VE : IR Cut Filter
Remove
IR Cut Filter Remove
Video
2010/2-1 03A.02
20
ZC-Y11VE/ZN-NH11VE/ZN-NHW11VE Installation Guide
Compression Format
H.264, MPEG-4, MJPEG Selectable per Stream
Number of Streams
Dual Stream, Configurable
Resolution
D1, 4CIF, VGA, CIF, QCIF, QVGA
Compression FPS
Deinterlacing
25/30 [email protected] (PAL/NTSC)
Supported (DSP)
Motion Detection
Supported
OSD
Supported (DSP)
Burnt-in Text (Digital)
Output
Supported (DSP)
1 Loop Out (BNC connector)
Audio
Input / Output
1/1 channel
Compression Format
G.711
Function
Digital Input / Ouput
RS-485
1/1 channel
Supported
Network
10/100 Base-T
TCP/IP, UDP/IP, HTTP, RTSP, RTCP, RTP/UDP, RTP/TCP,
SNTP, mDNS, UPnP, SMTP, SOCK, IGMP, DHCP,
FTP, DDNS, SSL v2/v3, IEEE 802.1X, SSH
Supported
Protocol
USB 2.0
SD Slot
Supported (Micro SD)
※ Micro SD Card is not included
Material
Aluminum
Dimensions
55(W) x 55(H) x 94.2(D) mm
Electrical Characteristics
Analog Video Output
Audio Input
Audio Output
Sensor(D/I)
Alarm(D/O)
Power Source(Approx)
1Vp-p, 75О©
Linein, 1.43Vp-p(Min 1.35Vp-p, max 1.49 Vp-p), 39 KО©
Lineout, 46mW Power, 16 О©
TTL level 4.5V threshold, Max 50mA
Max [email protected] or [email protected]
12 V DC 340 mA or PoE IEEE802.3af(class 0)
Environment Condition
Operating Temperature
Operating Humidity
0 ЛљC ~ 50 ЛљC (32ЛљF ~ 122 ЛљF)
Up to 85% RH
VCA (Video Content Analysis)
2010/2-1 03A.02
21
ZC-Y11VE/ZN-NH11VE/ZN-NHW11VE Installation Guide
VCA Presence (Included as Standard)
High Performance
Advanced Tracking Algorithm, Low False Alarm Rate
Easy to Use
Intuitive Web Browser Interface
Detection Zones
Multi-segment Polygons and Lines
On-screen Display
Real-time Display of Tracking Data and Events
Stream or Analog video out
Burnt-in Annotation
(※Analog video out support can vary depending on the device
model and hardware version and the firmware version)
VCA Surveillance (Optional)
Detection Behavior
Camera Tampering, Direction, Stopping, Loitering, Entering,
Exiting, Appear, and Disappear Filters
3D Behavior
Perspective Corrected Size and Speed Filters
Statistics
Counting Functions and Other Statistics
Meta Data
Binary XML Format
Image Stabilization (Optional)
Electronic Stabilization
Removes Camera Sway
2010/2-1 03A.02
22
ZC-Y11VE/ZN-NH11VE/ZN-NHW11VE Installation Guide
APPENDIX (B): POWER OVER ETHERNET
The Power over Ethernet(PoE) is designed to extract power from a conventional twisted pair
Category 5 Ethernet cable, conforming to the IEEE 802.3af Power-over-Ethernet (PoE) standard.
IEEE 802.3af allows for two power options for Category 5 cables.
The PoE module signature and control circuit provides the PoE compatibility signature and
power classification required by the Power Sourcing Equipment (PSE) before applying up to
15W power to the port.
The high efficiency DC/DC converter operates over a wide input voltage range and provides a
regulated low ripple and low noise output. The DC/DC converter also has built-in overload and
short-circuit output protection.
PoE compatibility
With non Power Sourcing Equipment (PSE)
When it is connected with non PSE, the power adaptor should be connected.
With power adaptor
Connecting both PSE and power adaptor does not do any harm to the products. Disconnecting
power adaptor while it is operating does not stop operation. The product continues to work
without rebooting.
Power classification
The PoE Power Class supported by the IP device is Class 0.
Class
Usage
Minimum Power Levels
Output at the PSE
Maximum Power Levels at the
Powered Device
0
Default
15.4W
0.44 to 12.95W
2010/2-1 03A.02
23
ZC-Y11VE/ZN-NH11VE/ZN-NHW11VE Installation Guide
APPENDIX (C): DIMENSIONS
55
91.4
94.2
55
Front view
Top view
LOOP OUT
RESET
RS-485
- +
DO
DI
C 1 C 1
AUDIO
Out In
Micro SD
ETHERNET
Rear view
H.264 Network Camera
Right side view
2010/2-1 03A.02
UNIT: mm
24
ZC-Y11VE/ZN-NH11VE/ZN-NHW11VE Installation Guide
APPENDIX (E): TROUBLE SHOOTING
Checking your Firmware
Firmware is software that determines the functionality of the device. One of your first actions
when troubleshooting a problem should be to check the currently installed version. The latest
version may contain a correction that fixes your particular problem. The current firmware
version in your device can be seen under Setup > About > Version.
New firmware can be downloaded at the FTP site. When you download firmware from the FTP,
your product will receive the latest available functionality. Always read the upgrade
instructions and release notes available with each new release, before updating the firmware.
Please contact us to get an FTP account.
Support
If you cannot resolve an issue, for additional assistance, please contact your supplier or system
integrator.
If you contact our support, please help us help you resolve your problems expediently by
providing a server report, log file and a brief description of the problem.
1. In the address bar of your browser, after the unit IP address enter following CGI
command.
<IP ADDRESS> /nvc-cgi/admin/param.cgi?action=list
The server report contains important information about the device, as well as a list of
the current parameters.
2. The Log messages in the device can prove a useful diagnostic tool for troubleshooting.
Go to Setup > Maintenance > System Log > LOG LIST > message.
2010/2-1 03A.02
25
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement