advertisement
K3
K3
Digital karaoke processor
Manual
Contents
1 、 Safety Instruction 2
2 、 Product Overview 3
3
、
Front Panel Connections 4
4
、
Rear Panel Connections 5
5
、
Boot Screen 6
6
、
Music Function Instructions
6.1
、
Music Input Line Option 7
6.1.1
、
Analog Music Input 7
6.1.2
、
Digital Audio Format Input (S / PDIF) 7
6.2
、
Music Volume Setting 7
6.3
、 Music Tone Set 8
6.4
、 Music PEQ Settings 8
6.5
、
The Maximum Volume Setting 8
6.6
、
Music Noise Gate Settings 8
6.7
、
The Music Low-Cut Set 8
7
、
Microphone Function Instructions
7.1
、
Microphone Input and Potentiometer Settings 8
7.2
、
Microphone Volume Settings 8
7.3
、
Microphone Enhancement Feature 8
7.4
、 Microphone Optimization Settings 9
7.5
、 Microphone Noise Gate Settings 9
7.6
、 Microphone Feedback Elimination Settings 9
7.7
、、
Microphone High & Low-Cut Setting 9
7.8
、
Microphone PEQ Settings 10
7.9
、
Microphone Direct Sound Volume, Phase Settings 10
7.10
、
The Effect Volume Settings 11
7.11
、
The High and Low-Cut of Effect Setting 11
7.12
、
The Effect of the PEQ Settings 11
7.13
、
Echo Volume & Phase Settings 12
7.14
、 Echo Delay Setting 12
7.15
、 The Maximum Volume of Effect Setting 12
7.16
、 Echo Mode, Echo Thickness Settings 13
7.17
、
The Reverberation Volume & Phase Settings 13
7.18
、
Reverb Pre-Delay & Reverb Time Setting 13
7.19
、
Reverb Type Setting 14
8
、
Main Output Function Instruction
8.1
、
Main Output Volume, PEQ Setting 14
8.2
、
Direct Sound to the Main Output, Effect to the Main
Output Volume Setting 15
8.3
、 Music to Center Volume Settings 15
8.4
、 Main Output PEQ Settings 15
8.5
、
Left & Right Delay Settings of Main Output 16
8.6
、
The Main Output Limit Settings 16
9 、 Center Part Function Instruction
9.1
、 Center Volume Setting 17
9.2
、
Direct Sound to the Center,
Effect to Center Volume Setting 17
9.3
、
Center Musical Delay,
Music to Center Volume Set 17
9.4
、
Center PEQ 18
9.5
、
Center High & Low-Cut Settings 18
10
、
Sub Woofer Features
10.1
、 Sub Woofer Level and Phase Settings 19
10.2
、 Sub Woofer High & Low-Cut Settings 19
10.3
、
Sub Woofer PEQ Settings 20
10.4
、
Sub Woofer Music Delay set Direct Sound to the Sub
Woofer Volume Settings 20
10.5
、
Sub Woofer Limit Settings 20
1 Program Features Instruction
11.1
、
Program Saved 21
11.2
、
Program Recall 22
11.3
、 Program Delete(PC software interface features) 22
11.4
、 Program Data is saved to the Computer
(PC software interface features) 22
11.5
、
Program Upload the Data from the Computer to the
Processor (PC software interface features) 22
12
、
Power-On Upload Options 22
13
、
Volume, Gain Maximum Limit Functions 22
14
、
Volume Fader Function 22
15 、 Sub Woofer Output Options 23
16 、 Music Pitch Auto-Recovery Function 23
17 、 Panel Lock, Parameter Lock Function
17.1
、
Panel Lock Function 23
17.2
、
Parameter Lock Function 23
18
、
Power-On Reset Function 23
19
、
Automatically Return to the Boot Screen Function 23
20
、
Language Options 23
21
、
Remote Control Function
21.1
、 Wireless Remote Control 24
21.2
、 Line Remote Control Function 24
22
、
Computer Interface Software Control Functions 25
23
、
Important Notes on PC Control
24
、
Accessories 25
25
、
Technical Specifications 26
1
IMPORTANT SAFETY INSTRUCTIO
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER ( OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED PERSONNEL
The lightning flash with arrowhead synbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure, that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operation and maintenace (servicing) instruction in the literature accompanying the appliance.
Please see below basic protection proceeding before using:
1. Please read all the safety instruction before using the product.
2. This product must be earthed. If it should be malfunction or break down, grounding provides a path of least resistance for electric current to reduce risk of electric shock.
This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and earthed in accordance with all local codes and ordinance.
DANGER- Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product - if it will not fit the outlet, have a proper outlet installed by a qualified electrician.
3. To reduce the risk of injury, close supervision is necessary when the product is used near children.
4. Do not use this product near water-for example, near a bathtub, washbowl, kitchen sink, in wet basement or near a swimming pool or the lake.
5. This product may be capable of producing sound levels that cloud cause permanent hearing loss. Do not operate for a long period of time at high volume level or at a level that is uncomfortable. If you experience any hearing loss or ringing in the ears, you should consult an audiologist.
6. This product should be located so that its location or position does not interfere with its proper ventilation.
7. This product should be located away from heat sources such as radiators, heat registers or other products that produce heat.
8. The product should be connected to a power supply only of the type described on the operation instructions or as marked on the product.
9. This product may be equipped with a polarized line plug (one blade wider than the other). This is a safety feature. If you are unable to insert the plug into the outlet, contact an electrician to replace your obsolete outlet. Do not defeat the safety purpose of the plug.
10. The power-supply cord of the product should be unplugged from the outlet when left unused for a long period of time.
When unplugging the power-supply cord, do not pull on the cord, but grasp it by the plug.
11. Care should be taken so that object do not fall and liquid are not spilled into the enclosure through opening.
12. The product should be serviced by qualified service personnel when:
A
. The power-supply cord or the plug has been damaged; or
B
. Objects have been fallen, or liquid has been spilled into the product; or
C
. The product has been exposed to rain; or
D
. The product does not appear to operate normally or exhibits a marked change in performance; or
E
. The product has been dropped or the enclosure damaged..
13. Do not attempt to service the product beyond that described in the user-maintenance instructions.
All other servicing should be referred to qualified service personnel.
on or roll anything over it. Do not allow the product to rest on or to be installed over power cords of any type. Improper installations of this type create the possibility of fire hazard and/or personal injury.
SAVE THESE INSTRUCTIONS
Version:V1.0
2
2、Product Overview
K3
1
MIC
2 3
USER PROGRAM PARAMETER
1 2
3
4
STORE
MIC ENHANCE MIC MODE EFF MODE MUS MODE MAIN MODE
CENT MODE
SUB MODE
MUS VOL/EDIT(PUSH)
MIC VOL EFF VOL
★ The product uses 56-bit high-performance DSP and 24bit AD / DA, 48kHz sampling frequency of professional digital multi-channel karaoke processor
★ high performance professional concerts effect (reverb, echo, dual-echo, reverb + echo).
★
Feedback eliminating multi-level optional.
★
15-level stereo digital keying music tone.
★
7-band parametric equalizer filter for music(can be set to a low -shelf/ high-shelf filter).
★
10-band parametric equalizer filter for Microphone (can be set to low shelf//high-shelf filter).
★
3-band parametric equalizer filter for effect (can be set to low shelf//high-shelf filter).
★ 5-band parametric equalizer filter for Main output(can be set to low shelf//high-shelf filter).
★
3-band parametric equalizer filter for Sub woofer (can be set to low shelf//high-shelf filter).
★
3-band parametric EQ filter equalizer filter for Center (can be set to low shelf//high-shelf filter).
★
3 group audio-video automatic priority input and background music (BGM).
★
Knob parameter adjustment of all-digital operation more convenient.
★ VOD interface (RS232), wireless infrared remote control, remote line interface (external remote receiver).
★
Computer interface software connect to unit via RS232, USB ports, all parameters adjustable.
★
Extremely low noise.
★ Subwoofer volume
Automatic mode: volume automatically switch between concert and dance.
Manual mode: remains unchanged
★
Power-on program loading Optional: Keep the last program before turn off ; User program 1-4
★
132 * 32 dot-matrix LCD screen, display more intuitive.
★ Large capacity storage: 15 preset, 30 user programmable.
3
3、Front panel instruction
1 2
3
4
5 6
K3
1
MIC
2 3
USER PROGRAM
2 3
PARAMETER
1 4
STORE
MIC ENHANCE MIC MODE EFF MODE MUS MODE MAIN MODE CENT MODE SUB MODE
MUS VOL/EDIT(PUSH) MIC VOL EFF VOL
7 8 9 10 11 12 13 14 15 16 17
1
、
3-ways microphone input jack and volume control potentiometer
2
、
132 * 32 dot- matrix LCD display is used to display a variety of menus and parameter adjustment information.
3
、
Infrared remote control receiver window
4
、
User programming keys
5
、
Storage program key
6
、
Menu parameter switch key (in the start-up screen show the music rising tone, falling tone)
7 、 Microphone enhance keys
8
、
Microphone mode key
9
、
Effect mode key
10
、
Music mode key
11
、
Main output mode key
12 、 Center mode key
13
、
Subwoofer mode key
14
、
Music volume knob ("edit" function in the menu screen, adjust menu parameters, "ress " function is switch other parameters in the same menu screen)
15
、
Microphone volume knob
16
、 effect volume knob
17
、
USB Connection
4
4、Rear Panel instruction
1 2 3 4 6 8 10
11 12 13 14 15 16 17
POWER
~90V-250V
50-60Hz
Made In China
R S 2 3 2
S/PDIF
OPTIC
CENT
LINE REMOTE
BGM
INPUT
ADJUST
IN1
-
∞
+3dB
OUT
VIDEO
IN2
L
BGM IN1
AUDIO INPUT
IN2
AUX OUT
REC OUT
R
SUB RIGHT LEFT
4
MIC INPUT
5
5 7 9
1
、
Power Switch (T1AL/250VAC)
2
、
Standard IEC Power Input (~ 90V-220V)
3 、 RS232 interface
4
、
Digital Audio Output (S / PDIF)
5
、
The OPTIC Interface (fiber interface)
6
、
Main Output
7
、
Remote Line Interface (external remote receiver)
8
、
3-way video inputs: the background music (BGM) "," Input 1 "," Input 2 "
9
、
1-way video output interface (selected from the 3-way input signal as the output signal)
10
、
Audio input level adjustment potentiometer
11 、 Stereo audio input interface: the background music (BGM) "," Input 1, Input 2
12
、
Auxiliary output (use as surround output)
13
、
Recording output
14
、
Sub woofer output
15
、
Right main output
16 、 Left main output
17
、
Microphone inputs
5
5、Power-On processor.
Connect power cable, press the power switch on the rear panel, screen display trademark will be shown as below:
K3
Then the version No#, the processor unit starts loading data
(the boot loaded data can be set after the boot, there are 5 options:
[the last memory before turn-off], [1-4 user program],here show the selected set).
Version *.*
Loading[USER 1]
Loading is complete, display boot screen, as follows:
MIC: 9.0dB BMUS: 15.0dB
EFF: 12.0dB
BGM A48 FBX 1
The boot screen shows the current microphone volume, music volume, effect volume
3-lines character and icon meaning is as follows:
The music input line (BGM/IN1/IN2)
Panel lock (" ", means the panel has been locked, no display indicates unlocked)
Encoder lock (" " means some parameters have been locked, no display indicates unlocked)
Subwoofer mode ( " " means concert mode," "means dance mode, no display indicates manual mode)
Musical input format ("A" represents the analog input "D" represents a digital input "44,48,32" represents the sampling rate)
Music pitch (" " )
Feedback eliminator status ("FBX1-5" indicates feedback eliminate grade 1-5, no display indicate feedback eliminator function closed)
MIC: 9.0dB BMUS: 15.0dB
EFF: 12.0dB
BGM A48 FBX 1
6
6、Music part operating instructions
6.1 Line select function of music input
6.1.1 analog music input
3-way analog music input line: background music, Input 1, Input 2
Potentiometer adjustment function, adjustment range: - 8 ~ +3 db
Method 1: continuously press panel buttons "music mode" until display to the music input selection screen, as shown below:
Music Input:
BGM
Panel
Turning the knob "music volume/edited (pressed)" to set music input lines.
Display
Method 2: setting from "device settings" of the interface software.
Method 3: use the remote control settings
FBE
PRESET/USER
BGM IN1 IN2
1
4
7
2
5
8
3
6
9
REMOTE CONTROL
6.1.2 digital audio format input (S /PDIF )
For different sampling rates (44.1khz/48khz) digital audio input, the machine will automatically recognize.
Method 1: Panel settings.
Method 2: setting from "device settings" of the interface software.
6.2 music volume set
Range: mute,-30db ~ 0db, Stepping: 0.5db
Operation 2: on the remote control music + " Music"
REMOTE CONTROL
Mic
+
Music
+
Mic
Music
-
-
Effe ct
Panel
Method 3: Operation from the interface software to set up
6.3 * Music tones
Range: b 7, b 6, b 5, b 4, b 3, B 2, B 1. # #1, #2, #3, #4, #5, #6 and #7
Method 1: The display on the screen.
Press the key on the panel " <" and " >" to set the music tone..
Method 2: remote control "b"
" ", "#"
Panel
Method 3: Operation from the interface software to set up
Mic
+
Music
+
Mic
Music
-
-
Effe ct
REMOTE CONTROL
7
6.4. Music PEQ setting
PEQ: 7 bands
Type: Parametric equalization filters(can be set as low/high-tone filter), graphic equalization th
(the 7 band can be set up as a high-cut).
Frequency range: 20Hz - 20kHz
Gain range: - 15db ~ + 12 db(can be limited to +6db in the "evice Settings" of interface software),stepping is 0.1 db
Band range: 0.011 ~3.595
Operating method 1: (panel can only set the gain) press "usic mode" on panel continuously to enter the Music menu EQ,As below:
MUS PEQ2 292Hz -2.5
+ 6
- 6
Panel
Press the " <" and " >" set the EQ
Rotate the knob " music volume/edit (press)" to set the gain "
Method 2: by the interface software
(All the EQ parameters can be set)
Display
6.5 The maximum volume setting
Panel
Range: mute,-30db ~ 0db, Stepping: 0.5db
Method 1: continuously press buttons "music mode" to the maximum music volume screen, as below:
MUS MAX GAIN
0.0dB
Panel
Operation method 2: through the interface software to set up
Display
6.6. Music Noise Gate settings
Scope: On and Off
Operation: Set up through the interface software.
6.7. Music low-Cut set
Range: OFF, 20Hz ~200Hz, stepping 5 Hz
Operation: Set up through the interface software.
7, Microphone part instructions
7.1microphone input and potentiometer settings
There are a total of 5 microphone connector, 3 on the front panel, 2 on rear panel.
3-microphone on the front panel with Level Adjust input, in general, set in the middle is best.
7.2 Microphone Volume Setting
Range: mute, -25dB~+6dB, stepping 0.5 dB
Method 3: Operation from the interface software to set up
Panel
Mic
+
Music
+
Mic
-
Music
-
-
Effe ct
REMOTE CONTROL
8
7.3 Microphone Enhancement Feature
Range: adjust range - 50% (off) ~ + 50 %
Operating method 1: On the panel press the key "Music Enhance", set to continuously change enhance switch, turn the knob to adjust music inspired.
Operating method 2: Operation from the interface software to set up
MIC Enhance
+
8%
Panel
7.4 microphone optimization settings
Range: Off, Popular, Professional
Operation: Operation from the interface software to set up
7.6 microphone feedback elimination settings
Range: Off, Grade between 1 to 5.
Display
7.5 microphone noise gate settings
Range: Off, On
Operation: Operation from the interface software to set up
Feedback elimination on the screen, turning the knob "Music volume / Edit(Press) "to set the sensitivity
FBE
BGM
1
4
IN1
2
5
PRESET/USER
IN2
3
6
Panel
REMOTE CONTROL
Operating method 2: Operation from the interface software to set up
When the singer handheld microphone facing the speaker is singing, often occur howling/whistle, the phenomenon often makes the listener feel irritable, serious cases will damage the speaker and amplifier.
Adjustment the feedback elimination setting, howling will be eliminated automatically, effective protection of the speaker and amplifier.
Operation method 3: on the remote control "feedback inhibition" setting
7.7 microphone High-cut, Low-cut setting
Low-cut range: 20hz ~ 200hz, stepping 5hz
High-cut range: 12khz ~ 20khz, stepping 0.5khz
Operating Method 1: Press the panel button "microphone mode "into the microphone menu, selected to the microphone low-cut, high-cut screen, as shown below:
Panel
Keys "<" and ">" switch Low-cut and High-cut.
Operating method 2: Operation from the interface software to set up
HPF:
OUT
45Hz
MIC
LPF:14.5kHz
FREQ
Display
Panel
9
7.8 microphone PEQ settings
Balanced qty: 10
Type: parametric equalization filter (can be set to low / treble tone filter), graphic equalizer
Frequency range: 20hz ~ 20khz
" in the interface software), step 0.1db
Bandwidth range: 0.011 to 3.595
until show MIC PEQ as below:
Panel
"
MIC PEQ1 80.3Hz
+ 5.9
+ 6
- 6
Display
Buttons "<" and ">" to select the desired setting PEQ
Turning knob music volume / edit (press) to set the gain
Operating method 2: Operation from the interface software to set up(all equalizer parameters can be set)
Panel
7.9 microphone direct sound volume, phase settings
Volume range: 0% ~100%, Stepping: 1%
Phase range: 0 180 selected the direct sound and phase, as shown below:
Panel
Keys "<" and ">" to switch direct sound and phase.
Turning knob "usic volume / edit (press) "to set
Operating method 2: Operation from the interface software to set up
MIC DIR VOL
PHASE
100%
[0 ]
Display
Panel
10
7.10 effect volume set
Range: mute,-30db ~ 0db, Stepping: 0.5db
Operating method 3: Operation from the interface software to set up
Panel
Mic
+
Music
+
Mic
-
Music
-
-
Effe ct
REMOTE CONTROL
7.11 Effect high-cut, low-cut set
Low-cut range: OFF, 50hz - 200hz, stepping 5hz
High-cut range: 8khz ~ 16khz, OFF, stepping 0.5khz
Operating : Operation from the interface software to set up
7.12 Effect PEQ set
The PEQ qty: 3
Type: parametric equalization filter (can be set to low / treble tone filter), graphic equalizer
Frequency range: 20hz ~ 20khz
Gain Range:-15db ~ +12 db, step 0.1db
Bandwidth range: 0.011 to 3.595
Operation: (panel only set the gain of equalizer )
Panel
Buttons "<" and ">" to select the desired setting PEQ
Operating method 2: Operation from the interface software to set up(all equalization parameters can be set)
EFF PEQ
1
101Hz
+ 6
- 6
0.0
Display
Panel
11
7.13 Echo volume, phase settings
Volume range: mute,-30db ~ 0db, Stepping: 0.5db
Phase range: 0 , 180 operation: Press the buttons "Effect Mode" on the panel continuously into the echo volume and phase screen, as shown below:
ECHO VOL
PHASE
-
10.0dB
[0 ]
Panel
Buttons "<" and ">" to switch Echo volume and phase
Turning knob "music volume / edit (press) "to set .
Display
Operating method 2: Operation from the interface software to set up
7.14 Echo delay set
Delay range: 100ms-600ms, stepper: 5ms "
Panel
Depth range: 0% -100%, Stepping: 1%:
Operation: Press the buttons "Effect Mode" on the panel continuously into the effect delay, as shown below:
ECHO DELAY
200ms
ECHO DEPTH 60%
Panel
Button "<", ">" Switching echo delay and depth.
Turning knob "music volume / edit (press) "to set
Operating method 2: Operation from the interface software to set up
Display
7.15 Effect maximum volume setting
Range: mute,-30db ~ 0db, Stepping: 0.5db
Panel
Operation: Press the buttons "Effect Mode" on the panel continuously into the effect maximum volume, as shown below:
EFF MAX VOL
0.0dB
Panel
Turning knob "music volume / edit (press) "to set the maximum volume.
Operating method 2: Operation from the interface software to set up
Display
Panel
12
7.16 Echo mode, Echo thickness settings
Range: Single, stereo, dual echo
Range: On, Off
Operation: Press the buttons "Effect Mode" on the panel continuously into the Echo Mode/ Echo Thickness, as shown below:
ECHO MODE
MONO
ECHO TO REV OFF
Panel
Display
Keys "<" and ">" Switch echo pattern and thickness.
Turning knob "music volume / edit (press) "to set
Operating method 2: operation from the interface software to set up
7.17 Reverb volume, phase settings
Volume range: mute,-30db ~ 0db, Stepping: 0.5db
Panel
Phase range: 0 , 180
Operation: Press the buttons "Effect Mode" on the panel continuously into the Reverb
Volume/ Phase, as shown below:
REV VOL
PHASE
-
10.0dB
[0 ]
Panel
Keys "<" and ">" switch reverb volume and phase.
Turning knob "music volume / edit (press) "to set
Operating method 2: Operation from the interface software to set up
Display
7.18 reverb pre-delay, reverb-time setting
Reverb pre-delay range :0-250ms, Stepping: 10ms
Panel
Reverb-time range :0.5-6s, Stepping: 0.1s
Operation: Press the buttons "Effect Mode" on the panel continuously into the Reverb
Pre-delay/ Reverb-time, as shown below
REV PRE-DELAY
0ms
REV TIME
3.2s
Panel
Display
Keys "<" and ">" switch reverb pre-delay and reverb-Time.
Turning knob "music volume / edit (press) "to set
:
Operating method 2: Operation from the interface software to set up
Panel
13
7.19 reverb type set
Range: 1.off ; 2. Room ; 3 Small hall; 4.Hall; 5. Church; 6. Cathedral; 7. Vocal.
Operation: Press the buttons "Effect Mode" on the panel continuously into the Reverb Type, as shown below:
Panel
Turning knob "music volume / Edit (press)" to set the reverb type
Operating method 2: Operation from the interface software to set up
REV TYPE
Room
Display
Panel
8、the main output section instructions
8.1 main output volume, balance setting
Range: mute,-30db ~ 0db, Stepping: 0.5db
Operation: Press the buttons "Main output Mode" on the panel continuously into the Main output volume and main output balance, as shown below:
MAIN OUT VOL
0.0dB
MAIN BALANCE L R 100%
Panel
Display
Keys "<" and ">" to switch the main output volume and main output balance.
Turning knob "music volume / edit (press) "to set
Operating method 2: Press keys "balance + " and" balance - " on the remote control.
Operating method 3: Operation from the interface software to set up
Panel
-
SUB
CENT +
CENT -
-
BAL
REMOTE CONTROL
REMOTE CONTROL
14
8.2 Direct sound to the main output, and the effect to the main output volume setting
Range: Mute,-30db ~ 0db, Stepping: 0.5db
Operation: Press the buttons "Main output Mode" on the panel continuously into the Direct sound to main output and
Effect to the main output volume, as shown below:
MIC DIR TO MAIN
EFF TO MAIN
-5.0dB
0.0dB
Panel
Display
Keys "<" and ">" to switch the needed parameters.
Turning knob "music volume / edit (press) "to set
Operating method 2: Operation from the interface software to set up
8.3 Music to the main output volume settings
Range: Mute,-30db ~ 0db, Stepping: 0.5db
Panel
Operation: Press the buttons "Main output Mode" on the panel continuously into the Music to main output volume, as shown below:
Panel
Turning knob " usic volume / edit (press) "to set
Operating method 2: Operation from the interface software to set up
MUS TO MAIN:
0.0dB
Display
8.4 main output PEQ settings
The PEQ qty: 5
Type: parametric equalization filter (can be set to low / treble tone filter) and graphic equalizer
Frequency range: 20hz ~ 20khz
Gain Range:-15db ~ +12 db, step 0.1db
Bandwidth range: 0.011 to 3.595
Methods of operation: (panel can only set the equalizer gain)Press the buttons "Main output Mode" on the panel continuously into the MAIN PEQ, as shown below:
As shown below:
Panel
MAIN PEQ
1
101Hz
+ 6
- 6
0.0
Display
15
Keys "<" and ">" to switch the needed PEQ.
Turning knob "music volume / edit (press) "to set Gain.
Operating method 2: Operation from the interface software to set up(all equalizer parameter can be set )
Panel
8.5 Main output left delay, right-delay setting
Range: 0.0ms ~ 5.0ms, stepping 0.1ms
Operation method1: Press the buttons "Main output Mode" on the panel continuously into the Main output delay, turning knob "usic volume / edit (press) "to set.
Operating method 2: Operation from the interface software to set up
8.6 Main output compression settings
Threshold range: -20 ~ +16 db, stepping 0.5db
Ratio: 2:1 4:1 8:1 16:1 32:1 64:1 128:1
Range: On, Off
Operation method1: (Only can set Threshold range and Ratio)Press the buttons "Main output Mode" on the panel continuously into the Main output compression, as shown below:
Panel
+16
OUT
-20
In
MUS COMP:
THRES RATIO
-7.0dB
2:1
Display
Keys "<" and ">" to switch the Threshold Rang and Ratio.
Turning knob " usic volume / edit (press) "to set.
Operating method 2: Operation from the interface software to set up
Panel
16
9、Center part operating instructions
9.1 Center volume setting
Range: Mute, -3
0db ~ 0db, Stepping: 0.5db
Operation method 1: Press the buttons "Center Mode" on the panel continuously into the Center volume , as shown below:
CENT VOL
0.0dB
CENT MAX VOL + 6.0dB
Panel
Display
Keys "<" and ">" to switch the center volume and microphone maximum volume.
Turning knob"usic volume / edit (press) "to set.
Operating method 2: Press on the keys "Center +" and ?Center -" on the remote control.
Operating method 3: Operation from the interface software to set up
SUB
+
-
SUB
CENT +
CENT -
BAL
+
-
BAL
REMOTE CONTROL
Panel
9.2 Direct sound to the center, Effect to the center volume setting
Range: mute,-30db ~ 0db, Stepping: 0.5db
REMOTE CONTROL
Operation method 1: Press the buttons "Mic Mode" on the panel continuously into the Direct sound to Center and Effect to center , as shown below:
MIC DIR TO CENT
-5.0dB
EFF TO CENT MUTE
Panel
Keys "<" and ">" to switch Direct sound to the center and Effect to the center.
Turning knob "usic volume / edit (press) "to set.
Operating method 2: Operation from the interface software to set up
Display
9.3 Center music delay, and The music to center volume set
Center Music delay range: 0 ~ 5ms, stepping 0.5ms
Panel
Music to the Center volume range: Mute,-30db ~ 0db, Stepping: 0.5db
How: Press the panel button microphone mode "election to set to music the delay, the volume of the music to the center screen, as shown below:
Operation method 1: Press the buttons "Mic Mode" on the panel continuously into the Center music delay and
Music to the Center volume , as shown below:
Panel
CENT DELAY:
0.0ms
MUS TO CENT: 0.0dB
Display
17
Keys "<" and ">" to switch Direct sound to the center and Effect to the center.
Turning knob "usic volume / edit (press) "to set.
Operating method 2: Operation from the interface software to set up
9.4 Center PEQ settings
The PEQ qty: 3
Type: parametric equalization filter (can be set to low / treble tone filter) and graphic equalizer.
Frequency range: 20hz ~ 20khz
Gain Range:-15db ~ +12 db, step 0.1db
Bandwidth range: 0.011 to 3.595
Panel
Operation method1: (Only can set EQ gain on the panel)Press the buttons "Mic Mode" on the panel continuously into the CENT PEQ, as shown below:
Panel
CENT PEQ
1
101Hz
+ 6
- 6
0.0
Display
Keys "<" and ">" to select the needing PEQ
Turning knob "usic volume / edit (press) "to set gain
.
Operating method 2: Operation from the interface software to set up
9.5 High-cut, low-cut settings
Low-cut range: OFF, 20Hz ~ 300Hz, stepping 5Hz
High-cut range: 2.5kHz ~ 20kHz, OFF, stepping 0.5khz
Operating method : Operation from the interface software to set up
Panel
18
10、The Sub woofer part operating instructions
10.1 Sub woofer volume and phase settings
Volume range: mute,-30db ~ 0db, Stepping: 0.5db
Phase range: 0 , 180
Operation method 1: Press the buttons "Sub Woofer Mode" on the panel continuously into the Sub woofer volume and phase, as shown below:
SUB VOL
-19.5dB
PHASE
[0 ]
Panel
Display
Keys "<" and ">" to switch the Sub woofer volume and phase
Turning knob "music volume / edit (press) "to set
Operation method 2: Press the keys "bass +" and "bass" on the remote control
Operating method 3: Operation from the interface software to set up
Panel
SUB
+
-
SUB
CENT +
CENT -
BAL
+
-
BAL
REMOTE CONTROL
REMOTE CONTROL
10.2 High-cut, Low-cut setting
Low-cut range: 19.7 ~ 1000hz,, 203 stepper
High-cut range: 35.1 ~ 2000hz, 209 stepper
Operation method 1: Press the buttons "Sub Woofer Mode" on the panel continuously into the Low-cut and High-cut, as shown below:
HPF:
19.7Hz
LPF:2000Hz
OUT
SUB FREQ
Panel
Display
Keys "<" and ">" to switch the High-cut and Low cut
Turning knob "music volume / edit (press) "to set
Operating method 2: Operation from the interface software to set up
Panel
19
10.3 Sub woofer PEQ settings
PEQ qty : 3
Type: parametric equalization filter (can be set to low / treble tone filter) and graphic equalizer
Frequency range: 20hz ~ 20khz
Gain Range:-15db ~ +12 db, stepping 0.1db
Bandwidth range: 0.011 to 3.595
Operation method 1: (Only can set EQ gain on the panel)Press the buttons "Sub Woofer Mode" on the panel continuously into the SUB PEQ, as shown below:
SUB PEQ3 120Hz
+ 10.0
+ 6
- 6
Panel
Display
Keys "<" and ">" to select the needing PEQ
Turning knob "music volume / edit (press) "to set gain
Operating method 2: Operation from the interface software to set up
(all the parameter of EQ can be set)
Panel
10.4 Subwoofer music delay, direct sound to the Subwoofer volume settings
Subwoofer music delay range: 0 ~ 20ms, stepping 0.5ms
Direct sound to the subwoofer range: MUTE,-30db ~ 0db, Stepping: 0.5db
Operation method 1: Press the buttons "MIC Mode" on the panel continuously into the Subwoofer music delay and
Direct sound to the subwoofer volume, as shown below:
SUB MUS DELAY:
0.0ms
MIC DIR TO SUB: 0.0dB
Panel
Display
Keys "<" and ">" to switch Subwoofer music delay and Direct sound to subwoofer volume
Turning knob "music volume / edit (press) "to set gain
Operating method 2: Operation from the interface software to set up
Panel
20
10.5 Subwoofer compressor settings
Threshold range: -20 ~ +16 db, stepping 0.5db
Ratio: 2:1 4:1 8:1 16:1 32:1 64:1 128:1
Range: On, Off
Operation method 1: (Only Threshold can be set )Press the buttons "Sub Mode" on the panel continuously into the
Subwoofer compressor, as shown below:
Panel
+16
OUT
-20
In
SUB COMP:
THRES:
-9.0dB
Display
Turning knob "music volume / edit (press) "to set Threshold
Operating method 2: Operation from the interface software to set up
11、Program/Memories management functions
The processor unit provides 15-preset programs and 30-user programs.
1 1.1 Program saved
Operation method 1: Press the keys "Save" on the panel, as below:
Panel
Save To
User Memory
1
Panel
Turning knob "music volume / edit (press) "to choose the program to save .
Press the key " ave? again to save the program.
Display
Operating method 2: Operation from the interface software to set up
11.2 program recall
Operating method 1: Press the keys[1], [2],[3], [4]: recall the program directly.
Operating method 2: by remote control
Operating method 3: Operation from the interface software to set up
Panel
Panel
BGM
1
4
7
0/30
IN1
2
5
8
10+
IN2
3
6
9
20+
REMOTE CONTROL
21
11.3 program deleted (computer software interface features)
11.4 program data is saved to the computer (computer software interface features)
11.5 program import the data from the computer to the processor (computer software interface features)
12 、Turn-On to load the selected program.
Connect the Processor unit to the computer ,open the software, set the program in"eboot effect"rom "evice setting"
(Program 1-4; Last program status before turn off).
Programs(memories)
1
-
4
The default program will be one of 1-4 whether or not making any parameter adjustment before reboot. This feature is to prevent extra work loaded applied to the
Musical Technicians.
Default program remain the same to prevent sudden power failure.
Last program
13
、
Volume, Maximum gain limit functions
Set through the online software interface with the computer: "Device Settings"
Maximum volume of the music: Mute,-30db ~ 0db, Stepping: 0.5db
Maximum volume of the microphone: Mute,-25db ~ +6 db, Stepping: 0.5db
Maximum volume of effect: mute,-30db ~ 0db, Stepping: 0.5db
Maximum volume of center: mute,-30db to 0db stepper: 0.5db
Maximum volume of subwoofer: Mute,-30db ~ 0db, Stepping: 0.5db
The maximum gain of music equalizer : +6.0 db to +12.0 db, Stepping: 0.1db
Volume limit feature: To protect and prevent damaging speakers and amplifier in a certain range.
To avoid setting too high volume destroyed the sound field. Example: When the microphone parameter is set to-10db, then the upper limit value of microphone volume is-10db, when using the microphone volume knob or the remote control to adjust the microphone volume, maximum output volume is -10db.
14 、 volume fader function
Set this function under "Device Settings" in the software provided.
the signal line, the signal is from small to large incremental increase; If the parameter set to "immediately", the signal is changed over directly without fading process.
22
15、Subwoofer output options.
Set this function under "Device Settings" in the software provided.
when the mode is manual, the subwoofer volume setting does not change.
when the mode is automatic: once the Microphone receives input signal, subwoofer output volume is the "concert" setting.
if Microphone has no input signal, a certain time later , the subwoofer volume will switch to "ance" settings automatically .
The following parameters are valid only in the automatic mode: concert volume, dance volume
The microphone detection threshold: When the microphone detects a level greater than this threshold, then determinate the microphone has input; otherwise determined to be no input.
The microphone detects time: when microphone no-signal input time more than this time, the subwoofer output volume will switch to "Dance" volume setting automatically.
16、music pitch automatic recovery function
The music pitch will adjust treble or bass when the user failed to meet the correct tone.
It will return to original musical setting after it.
17、panel lock, parameter lock function
17.1 panel lock function
Press the knob [music volume / edit (press)] more than 5 seconds to lock the system
Press the Knob [Music volume / Edit (press)] for more than 5 seconds to unlock the system.
17.2 parameter lock function
Operation from the interface software to set up
18、power-on reset function
Reset.....
Panel
Display
Note: After the reset, the user program will be deleted! Please stored in the computer in advance!
19、boot screen automatically returns
System will return to Start-Up screen automatically when no operation in 180s.
20、 Language selection function
To change system language, press [Center Mode] and [Bass Mode] same time.
23
21、 the wireless remote control
The easy-to-use remote control function, eliminating the need for manual operation. Simple parameter adjustment makes you to adjust the parameter settings used easily as picture shown below. :
FBX
BGM
1
4
7
0/30
IN1
2
5
8
10+
PRESET/USER
IN2
3
6
9
20+
MIC
+
MUSIC
+
EFFE
CT
+
MIC
-
MUSIC
-
SUB
+
-
SUB
CENT +
CENT -
-
EFF
ECT
BAL
+
-
BAL
REMOTE CONTROL
Keys
Feedback eliminate
Digit keys
BGM(background music)
、
Input 1
、
Input 2
Remote control keys function
Function
Adjust the feedback elimination
Press the digit keys to recall the memory directly
Adjust the music input line
"
"
10+
" "
20+
"
MIC+
、
MIC-
MUSIC+
、
MUSIC-
EFFECT+ 、 EFFECT-
Demote Tone
、
Original
Tone
、
Rise Tone
SUB+
、
SUB-
Cent+
、
Cent-
EQ+
、
EQ-
Press the "10 +" firstly, within 3 seconds press "0" ~ "9" can recall the memories 10 ~ 19 can recall the memories 20 ~ 299
Microphone volume Adjust
Music volume Adjust
Effect volume Adjust
Music Tone Adjust
SUB volume Adjust
Center volume Adjust
Main Left/Right output volume Adjust
Sheet 1 (the remote control code, data-digit hexadecimal)
2
3
4
Keys
Feedback Eliminate
Default / user
Background Music(BGM)
Code
0 0
0 1
0 4
0 3
Input 1
Output 2
1
0 2
0 5
0 6
0 7
0 A
Keys
5
6
7
8
9
0 / 3 0
1 0 +
2 0 +
MIC+
Code
0 9
0 8
0 B
0 C
0 D
1 0
0 F
0 E
1 1
Keys
MIC -
Music+
Music-
Effect+
Effect-
Reduce Tone
Original Tone
Rise Tone
SUB+
Code
1 7
1 6
1 5
1 4
1 B
1 2
1 8
1 3
1 9
21.1 line remote function
This function is an external remote control receiver. Line remote interface defines the following figure:
Keys
SUB-
Center +
Center -
EQ+
EQ-
Code
1 D
1 E
1 F
1 A
1 C
5V Power Output
Line remote control signal input
Ground
Line Remote Connect(processor rear panel socket)
24
22、When on-line computer interface software control the processor functions Online, the panel can not operate.
COM Port Detect Automatically.
Software can set all the parameters of the processor.
Please refer to the corresponding HELP documentation software instruction.
USB and RS232 cannot operate together. If RS232 interface is needed, please remove USB connection.
23、Important instruction on PC control
Please read the following instruction carefully before doing the connection.
Or there is more risks on abnormal conditions as offline, computer crash.
⑴ Please assure the AC power applies with the machine working condition.
⑵
The ground connection should be set with AC power.
Please use the AC power to connect the computer with the machine.
⑶
Do not install the control software with the same version and model repeatedly.
⑷
Do not load all the software in the same catalogue. Advise to set the separate file folder for saving the software.
⑸ Try to avoid doing the PC software control operation in the condition with strong signal interference.
⑹ The wrong operation will lead to fail controlling and even damage the machine and the computer.
a.Do not insert or pull out the connection interface at the power on condition before PC connection..
b.Do not move the computer, the machine and the connecting cable after PC connection.
c.Do not use the panel operation or touch the key on the panel after PC connection.
d.Do not insert or pull out the connection interface of the computer and the machine after successful
PC connection.
E.Do not use one computer to control several machines.
⑺ Please refer to IMPORTANT SAFETY INSTRUCTION in the user instruction.
AC Power
GROUNDING
Computer Iterface
24 Accessories:
Accessories
RS232 Computer Communication lines
Software CD
USB computer communication line
Manual
Remote Control
Qty
1
1
1
1
1
25
25、Technical Specification
Music parts
SNR
THD
Frequency response
Input sensitivity/ impedance
Max-output
Parametric EQ :5 bands
Type
Gain
Frequency:
Bandwidth:
Pitch Shift
Stereo audio input Level-adjustment
Video:
3-way video input, 1-way video output
Input Sensitivity/Impedance
Output Sensitivity/Impedance
Sub woofer parts
THD
Frequency Response
3-bands PEQ
Type
Gain
Frequency
Bandwidth
MIC parts
SNR
THD
Frequency Response
Input sensitivity/ impedance
Max-output
7-bands PEQ
Type
Gain
Frequency
Bandwidth
5-way MIC input
Remote
RS232
USB
Power Voltage
Fuse
Power-consumption
Weight
Size
26
>102dB(BYPASS , Pitch shift closed)
0.01% 20Hz-20kHz
20Hz-20kHz ± 0.5dB
0.707V/47kohm
14Vpp/60ohm EQ output
PEQ 、 High-shelf 、 Low-shelf
+12dB~-15dB , Stepping 0.1dB
20Hz~20kHz
0.011-3.595
7 Levels, Stepping 100 cents
∞ ~+0dB
1Vpp/75ohm
1Vpp/75ohm
0.01% 20Hz-2000Hz
20Hz-2000Hz ± 0.5dB
PEQ
、
High-shelf
、
Low-shelf
+12dB~-15dB , Stepping 0.1dB
20Hz~2000Hz
0.011-3.595
>100dB(Effect closed)
0.01% 50Hz-16kHz(Effect closed)
50Hz-16kHz ± 0.5dB
42mv/4.7kohm
13.8Vpp
PEQ
、
High-shelf
、
Low-shelf
+12dB~-15dB , step 0.1dB
20Hz~20kHz
0.011-3.595
1-way line control
,
5-pin socket
9-pin socket
AC 90-250V/50Hz
T1AL/250VAC
10W
2.2KG
45 482 123(mm)
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 Safety Instruction
- 4 Product Overview
- 5 Front Panel Connections
- 6 Rear Panel Connections
- 7 Boot Screen
- 8 Music Input Line Option
- 8 Analog Music Input
- 8 Digital Audio Format Input (S / PDIF)
- 8 Music Volume Setting
- 9 Music Tone Set
- 9 Music PEQ Settings
- 9 The Maximum Volume Setting
- 9 Music Noise Gate Settings
- 9 The Music Low-Cut Set
- 9 Microphone Input and Potentiometer Settings
- 9 Microphone Volume Settings
- 9 Microphone Enhancement Feature
- 10 Microphone Optimization Settings
- 10 Microphone Noise Gate Settings
- 10 Microphone Feedback Elimination Settings
- 10 Microphone High & Low-Cut Setting
- 11 Microphone PEQ Settings
- 12 The Effect Volume Settings
- 12 The High and Low-Cut of Effect Setting
- 12 The Effect of the PEQ Settings
- 13 Echo Volume & Phase Settings
- 13 Echo Delay Setting
- 13 The Maximum Volume of Effect Setting
- 14 Echo Mode, Echo Thickness Settings
- 14 The Reverberation Volume & Phase Settings
- 14 Reverb Pre-Delay & Reverb Time Setting
- 15 Reverb Type Setting
- 15 Main Output Volume, PEQ Setting
- 16 Output Volume Setting
- 16 Music to Center Volume Settings
- 16 Main Output PEQ Settings
- 17 Left & Right Delay Settings of Main Output
- 17 The Main Output Limit Settings
- 18 Center Volume Setting
- 18 Effect to Center Volume Setting
- 18 Music to Center Volume Set
- 19 Center PEQ
- 19 Center High & Low-Cut Settings
- 20 Sub Woofer Level and Phase Settings
- 20 Sub Woofer High & Low-Cut Settings
- 21 Sub Woofer PEQ Settings
- 21 Woofer Volume Settings
- 21 Sub Woofer Limit Settings
- 22 Program Saved
- 23 Program Recall
- 23 Program Delete(PC software interface features)
- 23 (PC software interface features)
- 23 Processor (PC software interface features)
- 23 Power-On Upload Options
- 23 Volume, Gain Maximum Limit Functions
- 23 Volume Fader Function
- 24 Sub Woofer Output Options
- 24 Music Pitch Auto-Recovery Function
- 24 Panel Lock Function
- 24 Parameter Lock Function
- 24 Power-On Reset Function
- 24 Automatically Return to the Boot Screen Function
- 24 Language Options
- 25 Wireless Remote Control
- 25 Line Remote Control Function
- 26 Computer Interface Software Control Functions
- 26 Accessories
- 27 Technical Specifications