Panasonic MCO-5M, (UV), UV O2/CO2 Incubator Operating Instructions

The Panasonic MCO-5M, MCO-5M(UV), and MCO-5MUV series O2/CO2 Incubators provide a controlled environment for cell culture applications. These incubators offer precise temperature, CO2, and O2 control to ensure optimal growth conditions for your cells.

PDF Download

Document

Operating Instructions
O2/CO2 Incubator
MCO-5M
MCO-5M(UV)
MCO-5M
MCO-5MUV Series
Please read these instructions carefully before using this product, and save this manual for future use.
See page 51 for all Model Nos.
CONTENTS
INTRODUCTION
P. 2
PRECAUTIONS FOR SAFE OPERATION
P. 3
LABELS ON THE INCUBATOR
P. 7
ENVIRONMENTAL CONDITIONS
P. 7
INCUBATOR COMPONENTS
P. 8
Control panel and keypad
P. 10
Remote alarm terminals
P. 12
INSTALLATION SITE
P. 13
INSTALLATION
P. 14
Connecting a CO2 gas cylinder
P. 15
Connecting a N2 (or O2) gas cylinder
P. 16
Connecting a gas injection nozzle
P. 17
PREVENTING CONTAMINATION
P. 18
PRECAUTIONS FOR CULTURES
P. 19
INITIAL CLEANING METHOD
P. 20
REMOVING INNER ATTACHMENTS
P. 21
INSTALLING INNER ATTACHMENTS
P. 23
FILLING THE HUMIDIFYING PAN
P. 24
WATER LEVEL SENSOR
P. 25
ROUTINE MAINTENANCE
P. 26
CORRECT OPERATION
P. 26
OPERATION OF KEYS ON THE CONTROL PANEL
P. 27
SETTING OF ALARM RESUME TIME
P. 28
Operation after power failure
P. 28
KEY LOCK FUNCTION
P. 29
AUTOMATIC GAS CYLINDER CHANGEOVER
P. 30
UV LAMP
P. 32
Change of setting for UV lamp ON period
P. 33
Precautions when using the UV lamp
P. 34
Lighting the UV lamp for 24 hours
P. 35
ALARMS, SAFETY, AND SELF-DIAGNOSIS
P. 36
CALIBRATION
Temperature calibration
P. 38
O2 calibration
P. 39
CO2 calibration
P. 40
TROUBLESHOOTING
P. 41
DISPOSING OF THE O2/CO2 INCUBATOR
P. 43
STACKING INCUBATORS
P. 48
SPECIFICATIONS
P. 50
PERFORMANCE
P. 51
SAFETY CHECK SHEET
P. 52
1
INTRODUCTION
■ Read this operating instruction carefully before using the Product and follow the instructions for safety
operation.
■ Our company disavows any responsibility for safety if the Product is used for other than the intended
use or used with any procedures other than those given in this operating instruction.
■ Keep this operating instruction in a suitable place so that it can be referred to as necessary.
■ The contents of this operating instruction are subject to change without notice for improvement of
performance or functions.
■ Contact our sales representative or agent if any page of the operating instruction is lost or the page
order is incorrect.
■ Contact our sales representative or agent if any point in this operating instruction is unclear or if there
are any inaccuracies.
■ No part of this operating instruction may be reproduced in any form without the expressed written
permission of our company.
CAUTION
Our company guarantees the product under certain warranty conditions.
way shall be responsible for any loss of content or damage of content.
2
Our company in no
PRECAUTIONS FOR SAFE OPERATION
It is imperative that the user complies with this operating instruction
as it contains important safety advice.
Items and procedures are described so that you can use this unit correctly and safely.
If the precautions advised are followed, this will prevent possible injury to the user and
any other person.
Precautions are illustrated in the following way:
WARNING
Failure to observe WARNING signs could result in a hazard to personnel
possibly resulting in serious injury or death.
CAUTION
Failure to observe CAUTION signs could result in injury to personnel and
damage to the unit and associated property.
Symbol shows;
this symbol means caution.
this symbol means an action is prohibited.
this symbol means an instruction must be followed.
Be sure to keep this operating instruction in a place accessible to users of this unit.
&lt; Label on the unit &gt;
This mark is labeled on the cover in which the electrical components of high voltage
are enclosed to prevent the electric shock.
The cover should be removed by a qualified engineer or a service personnel only.
WARNING
As with any equipment that uses CO2 gas, there is a likelihood of oxygen depletion in the vicinity
of the equipment. It is important that you assess the work site to ensure there is suitable and
sufficient ventilation. If restricted ventilation is suspected, then other methods of ensuring a
safe environment must be considered. These may include atmosphere monitoring and
warning devices.
3
PRECAUTIONS FOR SAFE OPERATION
WARNING
Do not use the unit outdoors. Current leakage or electric shock may result if the unit is exposed to
rain water.
Only qualified engineers or service personnel should install the unit.
unqualified personnel may cause electric shock or fire.
The installation by
Install the unit on a sturdy floor and take an adequate precaution to prevent the unit from
turning over. If the floor is not strong enough or the installation site is not adequate, this may result
in injury from the unit falling or tipping over.
Never install the unit in a humid place or a place where it is likely to be splashed by water.
Deterioration of the insulation may result which could cause current leakage or electric shock.
Never install the unit in a flammable or volatile location. This may cause explosion or fire.
Never install the unit where acid or corrosive gases are present as current leakage or electric
shock may result due to corrosion.
Always ground (earth) the unit to prevent electric shock. If the power supply outlet is not
grounded, it will be necessary to install a ground by qualified engineers.
Never ground the unit through a gas pipe, water main, telephone line or lightning rod. Such
grounding may cause electric shock in the case of an incomplete circuit.
Connect the unit to a power source as indicated on the rating label attached to the unit. Use
of any other voltage or frequency other than that on the rating label may cause fire or electric shock.
Never store volatile or flammable substances in this unit if the container cannot be sealed. These
may cause explosion or fire.
Do not insert metal objects such as a pin or a wire into any vent, gap or any outlet on the unit.
This may cause electric shock or injury by accidental contact with moving parts.
Use this unit in safe area when treating the poison, harmful or radiate articles. Improper use
may cause bad effect on your health or environment.
Turn off the power switch (if provided) and disconnect the power supply to the unit prior to any
repair or maintenance of the unit in order to prevent electric shock or injury.
Do not touch any electrical parts (such as power supply plug) or operate switches with a wet
hand. This may cause electric shock.
4
WARNING
Ensure you do not inhale or consume medication or aerosols from around the unit at the time of
maintenance. These may be harmful to your health.
Never splash water directly onto the unit as this may cause electric shock or short circuit.
Never put containers with liquid on the unit as this may cause electric shock or short circuit when
the liquid is spilled.
Never bind, process, or step on the power supply cord, or never damage or break the power
supply plug. A broken supply cord or plug may cause fire or electric shock.
Do not use the supply cord if its plug is loose. Such supply cord may cause fire or electric shock.
Never disassemble, repair, or modify the unit yourself. Any such work carried out by an
unauthorized person may result in fire, or electric shock or injury due to a malfunction.
Disconnect the power supply plug if there is something wrong with the unit.
abnormal operation may cause electric shock or fire.
Continued
When removing the plug from the power supply outlet, grip the power supply plug, not the cord.
Pulling the cord may result in electric shock or fire by short circuit.
Disconnect the power supply plug before moving the unit. Take care not to damage the power
cord. A damaged cord may cause electric shock or fire.
Disconnect the power plug when the unit is not used for long periods. Keeping the connection
may cause electric shock, current leakage, or fire due to the deterioration of insulation.
If the unit is to be stored unused in an unsupervised area for an extended period, ensure that
children do not have access and that doors cannot be closed completely.
The disposal of the unit should be accomplished by appropriate personnel. Remove doors to
prevent accidents such as suffocation.
Do not put the packing plastic bag within reach of children as suffocation may result.
5
PRECAUTIONS FOR SAFE OPERATION
CAUTION
This unit must be plugged into a dedicated circuit protected by branch circuit breaker.
Use a dedicated power source as indicated on the rating label attached to the unit. A multiple-tap
may cause fire resulting from abnormal heating.
Never store corrosive substances such as acid or alkali in this unit if the container cannot be
sealed. These may cause corrosion of inner components or electric parts.
Check the setting when starting up of operation after power failure or turning off of power
switch. The stored items may be damaged due to the change of setting.
Be careful not to tip over the unit during movement to prevent damage or injury.
Prepare a safety check sheet when you request any repair or maintenance for the safety of service
personnel.
6
LABELS ON THE INCUBATOR
Warning and caution labels are attached to the incubator. The following table describes the labels.
This label is attached to covers that access high-voltage electrical components to
prevent electric shock. Only a qualified engineer or service personnel should be
allowed to open these covers.
This symbol indicates an ultraviolet light (UV) caution.
This symbol indicates that caution is required. Refer to product documentation for
details.
This symbol indicates a hot surface.
This symbol indicates an earth.
This symbol means “ON” for a power switch.
This symbol means “OFF” for a power switch.
ENVIRONMENTAL CONDITIONS
This equipment is designed to be safe at least under the following conditions (based on the IEC 61010-1):
■ Indoor use;
■ Altitude up to 2000 m;
■ Ambient temperature 5 oC to 40 oC
■ Maximum relative humidity 80 % for temperature up to 31 oC decreasing linearly to 50 % relative
humidity at 40 oC;
■ Mains supply voltage fluctuations not to exceed &plusmn;10 % of the nominal voltage;
■ Other supply voltage fluctuations as stated by the manufacturer;
■ Transient overvoltages according to Installation Categories (Overvoltage Categories) II; For mains
supply the minimum and normal category is II;
■ Pollution degree 2 in accordance with IEC 60664.
7
INCUBATOR COMPONENTS
1
2
5
6
12
7 (inside)
22
MCO-5M(UV) or
when MCO-19UVS is
installed in MCO-5M
13 ,15 ,16(inside)
Changeable
9
4
8
14
19
23
8
19
3
Switch cover
Connecting port for N2/O2 gas
11
10
18
Connecting port for CO2 gas
17
20
21
MCO-5M(UV) or
when MCO-19UVS is
installed in MCO-5M
Rear right side
Rear left side
8
1. Outer door: Sticks to frame with magnetic seal. Door heater is installed in the door panel. The
door opening is reversible. Contact our sales representative or agent to change the door hinge from left
to right or vice versa.
2. Inner door: Made of tempered glass, however avoid excessive impact on the glass.
3. Leveling feet: Screw type for adjusting the height. Adjust the feet so that the unit can be level.
4. Tray: Can be pulled toward you.
5. Side support: Right and left side supports can be removed for disinfection. See page 21 and 22.
6. Rear duct: Flow path for circulating air. Removable.
7. Fan (inside the rear duct): Made from polypropylene resin. Can be sterilized by an autoclave.
8. Sample air outlet: This also functions as an internal gas outlet. Use only a supplied cap(9).
9. Sample air outlet cap: Always attach this cap except at the time of using of sample air outlet.
10. Connecting port A/B for CO2 gas pipe (rear side): When an optional component MCO-5GC (gas
auto changer) is installed, both A and B are available. If MCO-5GC is not installed, only A is available.
Refer to page 15 for gas cylinder connection. Ensure that the gas pressure is set at 0.03 MPa(G) (0.3
kgf/cm2(G), 4.3 psi(G)). Refer to page 30 for automatic gas cylinder changeover.
11. Connecting port A/B for N2/O2 gas pipe (rear side): Refer to page 16 for gas cylinder connection.
Ensure that gas pressure is set at 0.05 MPa(G) (0.5 kgf/cm2(G), 7.1 psi(G)). Refer to page 30 for
automatic gas cylinder changeover.
12. Door switch: Detects the door opening/closing and stops the circulating fan and electromagnetic
valve for CO2 and N2/O2 when door is open. UV lamp is also deactivated by door opening
(MCO-5M(UV) or when an optional UV system set MCO-19UVS is installed in MCO-5M).
13. Humidifying pan: Use sterile distilled water to fill the humidifying pan.
14. Humidifying pan cover: Prevents UV light being exposed to the chamber. When filling the
humidifying pan, lift the front side and take out the humidifying pan. See page 24 for details.
15. UV lamp (MCO-5M(UV) or when an optional UV system set MCO-19UVS is installed in MCO-5M):
This UV lamp does not generate ozone. Never look at the UV light directly. For replacement, contact
our sales representative or agent.
16. Water level sensor: Detects the water level in the humidifying pan. See page 25 for details.
17. Remote alarm terminal:
18. Access port:
Refer to page 12.
When not in use, cap with the silicon caps on both outside and inside.
19. Power switch: Main switch of the unit. Also functions as an over-current breaker. The switch is
covered by a switch cover to prevent the accidental push. To turn on or off the switch, remove the
switch cover by loosening the screw. See figure on the right.
20. Glow starter (MCO-5M(UV) or when an optional UV system set MCO-19UVS is installed in
MCO-5M): For UV lamp (model; FG-7P)
21. Removal power supply cord
22. Handle: Outer door handle. When moving the handle from upper to a lower position remove it from
original position first, then remove two cups and screws at the lower position and attach the handle there.
23. Gas injection nozzle: Refer to page 17.
9
INCUBATOR COMPONENTS
Control panel and keypad
3
2
1
8
9
10
11
4
5
6
7
1. Digital temperature indicator (TEMPERATURE oC): Normally, this indicator shows the chamber
temperature. In the setting mode, it shows the set value of the chamber temperature. If the self
diagnostic function detects any abnormality, an error code will be displayed.
2. Heater lamp (HEAT): This lamp lights when the heater is energized.
3. UV indicator (UV): This lamp lights when the UV lamp is ON.
recommends the replacement of UV lamp. See page 32 for the details.
The blink of this indicator
4. Door lamp (DOOR): This lamp lights when the outer door is open.
5. Water level alarm lamp (RH PAN): This lamp blinks when the water in the humidifying pan is less
than approximately 0.8 liter.
6. High limit regulator: This regulator is used to set the high limit temperature.
7. Over heat lamp (OVER HEAT): This lamp lights when the chamber temperature reaches the high
limit set value.
8. CO2 inject lamp (INJECT): This lamp lights when CO2 gas is being injected.
9. Digital CO2 density indicator (CO2 %): Normally, this indicator shows the CO2 density in the
chamber. In the setting mode, it indicates the set value of the CO2 density. The empty gas supply line
is displayed when CO2 gas cylinder becomes empty (only when MCO-5GC is installed). See page 30 for
details.
10. O2 inject lamp (INJECT): This lamp lights when N2 or O2 gas is being injected.
11. Digital O2 density indicator (O2 %): Normally, this indicator shows the O2 density in the chamber.
In the setting mode, it indicates the set value of the O2 density. The empty gas supply line is displayed
when N2 or O2 gas cylinder becomes empty (only when MCO-5GC is installed). See page 30 for details.
10
15
12
13
20
14
19
16
17
18
12. Set key (SET): Pressing this key to enter the setting mode, and the digits to be set will blink.
13. Calibration key (CAL): By pressing this key for approximately 5 seconds, the unit enters calibration
function mode. See page 38 for the details. Also, used to change the UV lamp ON period. See page
33 for the details.
14. Alarm buzzer stop key (BUZZER): Press this key to silence the buzzer when the alarm operates
and the buzzer sounds.
15. N2/O2 gas supply line indicator (A/B): The lamp for the N2/O2 gas supply line currently in use lights
up. (Lamp ON; cylinder A, Lamp blinks; cylinder B)
16. CO2 gas supply line indicator (A/B): The lamp for the CO2 gas supply line currently in use lights up
provided that gas auto changer MCO-5GC is installed. (Lamp ON; cylinder A, Lamp blinks; cylinder B)
17. Gas supply line switching key (GAS SUPPLY): This is a key to select N2 or O2 gas supply. By
pressing this key, the N2 or O2 gas supply line (A/B) is changed in O2 density set mode. The supply line
is changed automatically when N2 or O2 gas cylinder is empty. Similarly, by pressing this key in CO2
density set mode, CO2 gas supply line is changed automatically when a gas auto changer MCO-5GC
(option) is installed. The supply line is changed automatically when CO2 gas cylinder is empty.
18. Enter key (ENT): Pressing this key memorizes the set value in the controller.
19. Numerical value shift key ( ): Pressing this key in the setting mode causes the numerical value
to shift. In key lock mode, pressing this key makes key lock ON or OFF.
20. Digit shift key ( ): Pressing this key in the setting mode causes the changeable digit to shift.
Pressing this key more than 5 seconds enters key lock mode. See page 29 for the key lock.
11
INCUBATOR COMPONENTS
Remote alarm terminals
The remote alarm terminal is located at the rear right side.
Remote alarm terminal
The remote alarm terminal is a contact output.
Normal
: OPEN
Abnormal , blackout : CLOSE
Contact capacity
: DC 30 V, 2 A
Note:
• When the power switch is OFF or the power failure condition, the contact output is CLOSE.
• The remote alarm cannot be silenced by pressing the alarm buzzer stop key (BUZZER) since the
remote alarm is not conjunct with the alarm buzzer stop key (BUZZER) key.
REMOTE ALARM
MAX DC30V 2A
Remote alarm terminal
N. O.
12
INSTALLATION SITE
For correct operation of the incubator, install it in a location with the following conditions.
WARNING
When using CO2/N2 gas for control, make sure that there is adequate ventilation. Using CO2/N2 gas in
a small room without adequate ventilation may cause gas poisoning or oxygen deprivation. In addition,
when opening the incubator doors, do not directly inhale the air in the chamber.
Si l’appareil est utilis&eacute; dans un evdroit restreint, le niveau de la densite CO2/N2 de l’air peut s’&eacute;lever et
peut &ecirc;tre nocif aux humains. Evitez d’aspirer l’air provenant de l’in&eacute;rieur de l’appareil quand vous ouverz
la porte.
 Normal air environment
Install the incubator in an environment with normal air.
 Do not expose to direct sunlight
Do not install the incubator in a location where it will be exposed to direct sunlight. If the incubator is
operated in direct sunlight, performance will be adversely affected.
 Separate from heat sources
Do not install the incubator near significant heat sources, such as heaters, boilers, ovens, or autoclaves.
Heat will adversely affect the performance of the incubator.
 Ambient temperature at least 5 C lower than set temperature
The control temperature of the incubator is at least 5 C higher than the ambient temperature. For
example, if the chamber is controlled at 37 C, the ambient temperature must normally be no more than
32 C. Do not allow the ambient temperature to become too high.
 Strong and level floor
Select a site with a strong and level floor. If the floor is uneven or the installation is not level, the incubator
will be unstable and this may cause accident or injury. To avoid vibration and noise, always make sure
that the installation is stable. An unstable surface may result in vibration or noise.
WARNING
Install the incubator at a location that can support the weight. If the floor is not strong enough or if the
installation is insufficient, the incubator may fall over and cause injury.
Always make sure that the floor is strong, even, and level, and that the incubator will not tip over.
An insufficient installation may result in injury due to water leakage or the incubator falling over.
 Low humidity
Select a site with a relative humidity of 80 %R.H. or lower. Using the incubator in high humidity may result
in current leakage or electric shock.
WARNING
Do not use the incubator outdoors. If the incubator is exposed to rain water, it may result in current
leakage or electric shock.
Never install the Incubator in a moist location, such as near a sink or water line, or where it is
likely to be exposed to water. In addition, do not install it near water or steam pipes. Moisture can
cause the insulation to deteriorate, which may result in current leakage or electric shock.
 No inflammable or corrosive gas
Never install the incubator in a location where it will be exposed to inflammable or corrosive gas. Doing so
may result in explosion or fire. In addition, insulation may deteriorate due to corrosion of protective casing,
resulting in current leakage or electric shock.
 No falling objects
Do not install the incubator in a location where there is the possibility of objects falling from above. Doing
so may result in damage or accident.
13
INSTALLATION
1. Remove the packing tape and clean up.
Remove all the tape that is securing the doors and inner attachments. Open the doors for ventilation. If
the outer panels are dirty, dampen a cloth with a diluted neutral detergent and wipe them. (Using an
undiluted solution may damage the plastic. Follow the diluting instructions for the detergent that is used.)
Wipe off the residual detergent with a wet cloth and then wipe off any moisture.
Note:
Remove the cable tie banding the power supply cord. Prolonged banding may cause the corrosion of
the cord coating.
WARNING
Do not leave plastic wrapping bags within reach of children. If a bag is placed over a child’s head, it
can block the mouth and nose and cause suffocation.
2. Adjust the leveling feet.
Adjust the leveling feet by turning them counterclockwise to level
the incubator. (See the illustration on the right.)
3. Ground the incubator.
Ground the incubator during installation to prevent electric shock
in case the insulation is not sufficient. If there is no ground wire at
the location, consult with qualified service personnel.
 When a ground must be installed
If a grounded 3-pole outlet is not available, then a ground must
be installed. Consult with qualified service personnel.
Leveling feet
WARNING
To prevent electric shock, always ground the incubator. If grounding is not possible, then have a ground
installed by qualified personnel. If the incubator is not grounded, it may result in electric shock.
Never connect the ground wire to a gas pipe, water pipe, lightning rod, or telephone ground wire.
Doing so may cause electric shock.
 Installing a ground fault circuit breaker
If using the incubator in a location with moisture or humidity cannot be avoided, then it is recommended
that a ground fault circuit breaker be installed in the power supply circuit (i.e., the power supply at the
incubator). Have the circuit breaker installed by qualified service personnel.
CAUTION
Do not climb on the incubator or place objects on top of it. Doing so may damage it or cause it to fall
over, resulting in injury. If it is to be stacked, refer to page 48 and stack it securely.
 When the incubator is not in use
Empty the water from the humidifying pan and remove moisture from the chamber. Make sure that the
chamber is completely dry before closing the doors. Failure to do so may result in damage.
 Before moving the incubator
Before moving the incubator, empty the water from the humidifying pan, disconnect the power supply plug
from the outlet, and make sure that the cord will not be damaged. Failure to do so may result in electric
shock or fire.
14
Connecting a CO2 gas cylinder
WARNING
When connecting a gas cylinder to the incubator, confirm the gas type. Confirm that the connections
are secure and that no gas will escape. Be sure to use the specified pressure. Using an incorrect
gas or pressure may result in explosion or fire, or in gas poisoning or oxygen deprivation due to escaping
gas.
Install the incubator in a location with adequate ventilation. If adequate ventilation cannot be
provided, then install an alarm system using CO2 and O2 densitometers.
1. Use a liquefied CO2 gas cylinder (at least 99.5 % pure). The siphon (dip tube) type cannot be used.
2. Install a gas regulator rated at 25 MPa(G) (250 kgf/cm2(G), 3600 psi(G)) for the primary pressure, and
0.2 MPa(G) (2 kgf/cm2(G), 30 psi(G)) for the secondary pressure on the CO2 gas cylinder.
3. Using the gas tube that is provided, connect the gas regulator to the connecting port A/B for CO2 gas
pipe (located at the rear left side of the incubator).
Note:
If CO2 is supplied to multiple CO2 incubators from a single gas cylinder, a CO2 solid will be formed in the
gas regulator. The gas regulator safety valve will operate, and there may an explosive sound.
When the MCO-5GC is not mounted
Using the gas tube that is provided, connect the gas regulator for the CO2 gas cylinder to connecting port
A for CO2 gas pipe on the incubator. After connecting the gas tube, check to make sure that no gas is
leaking.
When the MCO-5GC is mounted
Connect a pair of CO2 gas cylinders with gas regulators independently. The gas supply line will be
switched automatically. Connect the main cylinder to connecting port A for CO2 gas pipe and the reserve
cylinder to connecting port B for CO2 gas pipe. After connecting the cylinders, check to make sure that no
gas is leaking.
 For details on installing the optional gas auto changer (MCO-5GC), refer to the MCO-5GC installation
guide. For details on using the MCO-5GC, refer to page 30.
4. Set the CO2 gas on the secondary side to 0.03 MPa(G) (0.3 kgf/cm2(G), 4.3 psi(G)) for gas injection. As
the pressure increases, the CO2 gas density control range will increase. Excessive pressure may cause
gas supply lines inside the incubator to come loose, which may result in gas poisoning or oxygen
deprivation due to the escaping of gas. If gas lines come loose, the incubator must be repaired.
 The gas lines connected to the incubator will degrade over time. If any deterioration or abnormalities
are found during inspection, replace the lines immediately.
15
INSTALLATION
Connecting a N2 (or O2 ) gas cylinder
WARNING
Check the gas type and ensure that it is fit for the purpose. Make sure that all pipes are
connected correctly and are not liable to become disconnected. Ensure that the gas pressure is
set at the specified value. Improper connection of the gas pipe or use of incorrect gas pressure
may result in leakage of gas. Elevated level of gas can be hazardous to health and may lead to
asphyxiation and risk of death.
This incubator needs N2 or O2 gas depending on the setting of O2 density. The selection is as follows:
When the setting of O2 density is less than 18 %: N2 gas
When the setting of O2 density is more than 22 %: O2 gas
O2 density in the atmosphere is about 20 %. For the control of O2 density in the chamber, O2 gas is
diluted by N2 gas when the setting of O2 density is less than that of the atmosphere. On the contrary, O2
gas is added when the setting of O2 density is more than that of the atmosphere.
1. Install a gas regulator rated at 25 MPa(G) (250 kgf/cm2(G), 3600 psi(G)) on the primary side and 0.2
MPa(G) (2.0 kgf/cm2(G), 30 psi(G)) on the secondary side on N2 or O2 gas cylinder.
2. Using the gas supply tube provided, connect the gas regulator to the connecting port A/B for N2 or O2
gas pipe located at the rear left side of the incubator. Connect the main cylinder to the connecting port A
for N2 or O2 gas pipe and connect the sub-cylinder to the connecting port B for N2 or O2 gas pipe so that
the gas supply can be switched automatically when one gas cylinder is empty. Connect the same gas
type to both connecting port A and B for N2 or O2 gas pipe . Never connect N2 gas and O2 gas at the
same time to the connecting port A and B for N2 or O2 gas pipe respectively.
3. Set the N2 or O2 gas pressure on the secondary side to 0.05 MPa(G) (0.5 kgf/cm2(G), 7.1psi(G)) (at gas
injection). The higher gas pressure makes control range of O2 density wider. In addition, excessive
pressure may cause disconnection of internal pipes inside the incubator, which will result in leakage of N2
or O2 gas into the atmosphere. Elevated level of CO2 gas or O2 gas can be hazardous to health and
may lead to asphyxiation and risk of death or fire by gas leakage. The repair of the incubator will be
necessary if the internal pipe is disconnected.
4. Check that no gas is leaking at any point where the pipe connects with the gas regulator or the
incubator.
 The gas lines connected to the incubator will degrade over time. If any deterioration or abnormalities
are found during inspection, replace the lines immediately.
WARNING
O2 gas increases the susceptibility of substances to burn. Take care of the handling of flame in a room
where the incubator is installed.
16
Connecting a gas injection nozzle
In the case of control of O2 density in the chamber, connect the gas injection nozzle to the gas injection
port by using the gas injection nozzle tube enclosed (inner diameter; 5 mm, outer diameter; 9 mm, length;
300 mm). This helps faster recovery of humidity after opening of the inner door.
Fill the humidifying pan with sterile distilled water so that the gas injection nozzle can be under the water
level.
1. Inside of unit is arranged as shown in Fig. 1 when humidifying pan cover removed. There is a gas
injection port in the lower left-hand corner.
2. Connect gas injection nozzle to gas injection port using gas injection nozzle tube. (Fig. 2)
3. Connecting gas injection nozzle is as shown in Fig. 3.
Gas injection nozzle
Gas injection port
Gas injection nozzle tube
Fig.1
Fig.2
17
Fig.3
PREVENTING CONTAMINATION
To prevent contamination of the chamber, select a suitable installation site.
 Avoid locations with high temperatures or humidity.
Avoid locations with high temperatures or humidity, because of a greater presence of microorganisms in
the air.
 Avoid locations with passers-by or drafts.
Avoid locations near doors, air conditioners, fans, etc., where passers-by or drafts can facilitate the entry
of microorganisms into the chamber.
 If possible, use a cleanroom.
To achieve a better culture, it is recommended that a cleanroom be used if one is available.
 Use clean containers.
The greatest cause of contamination is dirty containers for cultures. Be careful not to get containers or
trays dirty when taking them in and out.
 Keep the chamber clean.
Wipe off any fingerprints. If water spills from the humidifying pan, or if the doors are left open for a long
time, condensation may form on the inside of the doors. If that occurs, wipe off the condensation with a
dry sterile gauze. In particular, clean and disinfect the chamber if the culture medium is spilled. For details,
refer to “ROUTINE MAINTENANCE “on page 26.
 Use sterile distilled water in the humidifying pan.
Always use sterile distilled water in the humidifying pan. Do not use ultrapure water, because it may
cause red rust-like particles in the humidifying pan.
The water level alarm lamp (RH PAN) on the control panel blinks when the water level is low. Quickly refill
the sterile distilled water in the humidifying pan when the water level alarm blinks. Adding
low-temperature water will significantly lower the temperature in the chamber. Clean the humidifying pan
once a month.
 Keep the incubator out of direct airflows from air conditioners or fans.
Cool airflow from an air conditioner may cause condensation and lead to possible contamination.
18
PRECAUTIONS FOR CULTURES
 Leave space between culture containers.
Always leave space for ventilation between culture containers (Petri dishes, flasks, etc.). Inadequate
spacing may result in uneven temperature distribution and CO2/O2 gas density.
 Do not place harmful materials in the chamber.
Never place samples that release acidic, alkali, or corrosive gas in the chamber. Doing so may cause
damage resulting from discoloration or corrosion.
 Close the inner door.
Always close the inner door before closing the outer door. Failure to close the inner door will adversely
affect performance even if the outer door is closed.
 Open and close the doors gently.
Always open and close the doors gently. Closing the doors forcefully may cause spillage of the culture
medium, incomplete closing, or damage to the gasket. Before opening the inner door, check through the
glass to confirm that the UV lamp is OFF (if the MCO-5M(UV) or the optional UV system set MCO-19UVS
is installed in MCO-5M).
 Be careful when closing the outer door.
Use the handle when closing the outer door. Holding the door in other places may cause injury by getting
fingers caught in the door. Do not lean on the outer door. Doing so may result in injury from the outer door
coming loose or the incubator falling over, or it may cause current leakage or electric shock.
 Be careful of the inside of the outer door.
The inside of the outer door may become hot.
 Avoid using excessive force on the inner door.
Do not put your hand on the glass, poke it with sharp objects, or apply strong force. Doing so may result
in injury from breaking the glass.
 Check the cause of any alarm buzzer.
If an alarm buzzer sounds while the incubator is in use, immediately check the cause of the alarm. For
details on what may cause an alarm buzzer to sound, refer to page 36.
19
INITIAL CLEANING METHOD
Before using the incubator for the first time, clean dirt (tape residue, smear, etc.) from the
chamber and the inner attachments thoroughly. To keep the chamber clean is essential
to get the proper performance out of the incubator. Use the following steps to clean the
incubator properly.
1. Remove the inner attachments, referring to “REMOVING INNER ATTACHMENTS” on page 21.
2. Clean the removed inner attachments, chamber inside walls and inner door gaskets with a cloth or
sponge soaked in neutral detergent, diluted by 5 % or less. (Undiluted detergent can damage the plastic
components. For the dilution, refer to the instruction of the detergent.) (Fig. 1)
CAUTION
Do not use detergents or antiseptic solutions with acid, alkali, or chlorine. Doing so may cause
discoloration, corrosion, or rusting.
Be careful to keep the diluted detergent or water out of the temperature sensor, the CO2 gas injection
hole, the gas injection port, the inner sample air access port, the fan motor shaft bearing, and the inner
sample air outlet (Fig.2
). Also, do not wash the temperature sensor, the CO2 sensor, the O2 sensor,
the water level sensor and UV lamp using detergent. Doing so may cause failure.（Fig.2）
3. Soak a cloth or unwoven cloth in distilled water and wring it tightly, and then wipe off the residual
detergent thoroughly.
4. Wash the silicon caps (2 pcs) for the access port and the inner circulating fan using the above
mentioned detergent and rinse them with distilled water, and then autoclave them for sterilization (121 oC,
20 minutes).
5. Wipe up the inside walls, and the inner attachments like trays thoroughly with a cloth or unwoven cloth
soaked in alcohol for disinfection. Be careful not to leave any residue alcohol.
6. Reinstall the inner attachments correctly and securely, referring to “INSTALLING INNER
ATTACHMENTS” on page 23.
Silicon cap
CO2 sensor
O2 sensor
Temp. sensor
UV lamp
Fig. 1
Water level sensor
Fig. 2
20
REMOVING INNER ATTACHMENTS
CAUTION
Wear rubber gloves when performing maintenance on the chamber. Failure to wear gloves may
result in cuts or abrasions from sharp edges or corners.
Be careful not to damage the water level sensor or the UV lamp in the rear duct.
Do not use detergents or antiseptic solutions with acid, alkali, or chlorine. Doing so may cause
discoloration, corrosion, or rusting.
1. Turn OFF the power switch of the incubator.
2. Open the outer and inner doors and pull out the trays. (Fig. 1)
3. Lift the humidifying pan cover off from the pins at the rear side. (Fig. 2)
4. Pull out the humidifying pan. (Fig. 3)
5. Remove the screw by securing the clamp for the side support. (Fig. 4)
6. Remove the clamp. (Fig. 5)
7. Lift the side support off of the pins. (Fig. 6)
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
21
REMOVING INNER ATTACHMENTS
8. Lift the rear duct and remove it from the pins at the rear side. (Fig. 7)
9. Remove the fan by pulling out the central spring and then by pulling out the fan. (Fig. 8)
10. Remove the silicon caps of the access port, one each from interior (Fig. 9) and exterior (Fig. 10).
①Pull out the central spring
②Pull out the fan
Fig. 7
Fig. 8
Fig. 9
Fig. 10
22
INSTALLING INNER ATTACHMENTS
Use the following steps to install the inner attachments properly.
1. To reinstall all the attachments, perform the procedure in reverse order from step 10 on page 22.
2. When installing the fan, insert it to the motor shaft securely. Lightly turn the fan manually to make sure
that it does not strike the rear panel. Then put on the central spring. (Fig. 1)
CAUTION
If the fan is not inserted deep enough, the intended velocity performance cannot be achieved, which may
cause culture failure or insufficient decontamination.
3. To install the rear duct, confirm 4 pins are securely installed in the 4 holes of rear duct. (Fig. 2)
CAUTION
If the rear duct is fixed insecurely, the intended velocity performance cannot be achieved, which may
cause culture failure or insufficient decontamination.
① Push the fan deeply.
② Install the spring afterwards.
③ Lightly turn the fan manually to
make sure that it does not
strike the rear panel.
Fig. 1
Fig. 2
4. To install the side support, confirm the direction of fixing holes as shown in Fig. 3.
5. As shown in Fig. 4, set the tray with only the front edge bent up. If the tray is set in the wrong direction,
it may not be level and may become unstable.
Bent up
Fig. 3
23
Fig. 4
FILLING THE HUMIDIFYING PAN
Use the following procedure to fill the humidifying pan or to replace the water.
1. Lift the front side of the humidifying pan cover.
(Fig. 1)
2. Pull the humidifying pan forward. (Fig. 2)
3. Dispose of the remaining water in the humidifying
pan and clean the humidifying pan with a diluted
detergent. Then rinse it thoroughly with distilled
water and wipe it with alcohol for disinfection.
4. Wipe all moisture from the bottom of the chamber.
Fig. 1
5. Return the humidifying pan to the chamber and
add sterile distilled water (approx. 1.5 L, preheated
to 37 C). (Fig. 3)
6. Set the humidifying pan with the inner side flush
against the back, and replace the humidifying pan
cover. Close inner door and outer door, and confirm
that water level alarm lamp (RH PAN) on the control
panel is OFF.
Fig. 2
Note:
• Preheat to 37 C the water to be added to the
humidifying pan. Adding low-temperature water will
lower the temperature and humidity in the chamber.
• Replace the water in the humidifying pan by the
above procedure when the water level alarm lamp
blinks.
Fig. 3
CAUTION
When refilling the water in the humidifying pan, always wipe off any dirt from the water level sensor
with alcohol for disinfection. While doing that, be careful not to apply excessive force to the sensor lead
wire.
Caution:
In order to adjust the humidity inside the incubator chamber optimally and prevent condensation on the
chamber surface and inner door, it is designed to create the lower temperature area underneath the
humidifying pan to recondense the evaporated moisture in the humidifying pan. Although the
condensation may be seen round the humidifying pan on the bottom of chamber (inside the humidifying
pan cover), it is not a malfunction.
24
WATER LEVEL SENSOR
This incubator is equipped with a water level sensor. The water level sensor is set automatically when the
humidifying pan is installed. Take care not to damage the water level sensor when removing or installing
the humidifying pan.
When the humidifying pan is removed (side view)
Water level sensor
Humidifying pan
When the humidifying pan is installed (side view)
Note: Make sure that the humidifying pan is pushed all the way to the back and that the water level
sensor comes down when you install the humidifying pan.
Note:
• Lift the water level sensor before installing the humidifying pan if the water level sensor is in the lower
position after maintenance.
• When installing the humidifying pan, make sure that the humidifying pan is set properly and that water
level sensor comes down into the humidifying pan. The water level alarm lamp (RH PAN) blinks if the
water level sensor does not come down completely. If necessary, set the humidifying pan again in the
proper location.
• The water level sensor detects the water level every 30 minutes and just after the outer door is closed. It
takes several seconds to detect the water level. Therefore, the water level alarm lamp may flash a few
times after the outer door is closed even when the humidifying pan is full.
CAUTION
Foreign particles on the water surface can adhere to the water level sensor and fittings by capillary action
because the water level sensor is always in the water. The adhered foreign particles degrade water level
sensor performance and the water level alarm lamp may blink even though there is sufficient water in the
humidifying pan. Be sure to wipe OFF any dirt on the water level sensor with alcohol for disinfection
whenever you change the humidifying water. When cleaning the water level sensor, take care not to
apply excessive force to the lead wires.
25
ROUTINE MAINTENANCE
To use this unit in a clean condition, clean the chamber and the inner attachments at least once a month.
1. Remove the inner attachments by the procedures shown on page 21.
2. Clean the chamber and the inner attachments by the procedures shown on page 20.
3. Install the inner attachments by the procedures shown on page 23.
● When there is excessive dirt, contact our sales representative or agent.
CORRECT OPERATION
Use the following procedure to start trial operation or actual operation of the incubator.
1. Install the incubator correctly, referring to “INSTALLATION” on page 14.
2. Remove the packing materials from the chamber and inner attachments. Clean and disinfect the
chamber and inner attachments, referring to above “ROUTINE MAINTENANCE”.
3. Add approximately 1.5 L of sterile distilled water to the humidifying pan. (Refer to page 24.)
4. Turn ON the power switch at the lower part of the incubator.
Note:
The humidity in the incubator chamber is adjusted to the optimum setting. To prevent condensation on the
surface inside chamber and the inner door, there is a low-temperature area under the humidifying pan in
the bottom of chamber to recondense evaporated moisture. Condensation may occur around the
humidifying pan at the bottom of the chamber (on the inside of the humidifying pan cover), but this does
not indicate a problem.
26
OPERATION OF KEYS ON THE CONTROL PANEL
Table below shows the basic procedure for setting the chamber temperature, CO2 and O2 density. The
high limit alarm temperature setting is also shown in the table. Perform key operations in the sequence
indicated in the table. The example in the table is based on the assumption that the desired temperature
is 36.5 oC, CO2 density is 5 % and O2 density is 5 %. Adjustment of the high limit regulator should be
executed after the chamber temperature reaches the stable condition.
(The unit is set at the factory so that the chamber temperature is 37 oC, CO2 control is 0 % and O2 density
is 20 %.)
Allow at least 8 hours until the next setting after setting of desired chamber temperature and setting CO2
density to 0 %, at the time of first start-up or start-up after no use for long period.
Basic operation (Example: Chamber temperature; 36.5 oC, CO2 density; 5 % O2 density; 5 %)
Description of operation
1
Turn the power switch ON.
2
Press set key.
3
By pressing digit shift key and
numerical value shift key, set the
figure to 36.5.
4
Press enter key.
5
By pressing digit shift key and
numerical value shift key, set the
figure to 05.0.
6
Press enter key.
7
By pressing digit shift key and
numerical value shift key, set the
figure to 05.0.
8
Press enter key.
9
(Executed after the chamber
temperature reaches the stable
condition)
Adjust high limit regulator so that
the alarm temp. is 1 oC or more
higher than chamber temperature.
10
Press enter key.
Key operated
---SET
Indication after operation
The current chamber temperature is displayed
in digital temperature indicator.
The left digit blinks.
When pressed, the changeable digit is shifted.
When pressed, the figure of settable digit changes.
ENT
Set temperature is memorized.
Left digit in digital CO2 density
indicator blinks.
When pressed, the changeable digit is shifted.
When pressed, the figure of settable digit changes.
ENT
Set CO2 density is memorized, and
Left digit in digital O2 density indicator
blinks.
When pressed, the figure of settable digit changes.
When pressed, the changeable digit is shifted.
ENT
Set O2 density is memorized.
In digital CO2 density indicator, HI is displayed.
In digital temperature indicator, high limit temp. is
displayed. The high limit temp. can be changed
by turning high limit regulator.
ENT
This is the end of set mode and the indicators
display current temperature and density.
• In each setting mode, if the change of the setting is not necessary, pressing set key (SET) skips to next
setting mode.
• When the CO2 density is set to 00.0 % and O2 density is set between 18.1 % and 21.9 %, the control is
OFF regardless of the chamber atmosphere.
• The high limit temperature set value will change when the high limit regulator is turned even if the unit is
not in setting mode, because the alarm circuit is an independent circuit.
• In each setting mode, the indicator returns to the current temperature and density display mode
automatically when 90 seconds has passed without any key operation.
• The setting of O2 density is 70 % in maximum when the setting of CO2 density is higher than 10.1 %.
And, the setting of CO2 density is 10 % in maximum when the setting of O2 density is 70.1 %.
• Always ventilate the chamber when changing to CO2 control only from O2 control.
27
SETTING OF ALARM RESUME TIME
The alarm buzzer is silenced by pressing the alarm buzzer stop key (BUZZER) on the control panel
during alarm condition.
The buzzer will be activated again after certain suspension if the alarm condition is continued. The
suspension time can be set by following the procedure shown in the table below.
The example in the table is based on the assumption that the desired duration is 20 minutes.
Note: The duration is set in 30 minutes at the factory.
Table Changing procedure for alarm resume time (Ex: change from 30 minutes to 20 minutes)
Description of operation
1
Key operated
----
2
Press calibration key for 5 seconds.
3
Set the figure to F25
with the numerical value shift key
and digit shift key.
4
Press enter key.
5
Set the figure to 020 with the
numerical value shift key.
6
Press enter key.
Indication after operation
The current chamber temperature is
displayed.
The left digit blinks.
When pressed,
the figure of settable digit changes.
The settable digit is shifted.
ENT
The current setting is displayed.
The middle digit blinks.
When pressed, the figure of settable
digit changes.
ENT
The setting is memorized and
the current chamber temperature is
displayed.
• The settable alarm resume time are 0, 10, 20, 30, 40, 50, or 60 minutes (The setting is 000, 010, 020,
030, 040, 050 or 060 respectively). The buzzer would not reset if the reset time is set in 000.
• The set mode returns to the temperature display mode automatically when 90 seconds has passed
without any key operation. In this case, any setting before pressing the enter key (ENT) is not
memorized.
WARNING
Do not use calibration key (CAL) on the control panel in normal use. Pressing this key leads the
calibration mode. Wrong key operation affects the basic performance. Never touch any other keys on
the control panel in the event of pressing calibration key (CAL) accidentally. After about 90 seconds, the
unit returns to chamber temperature display mode automatically.
Operation after power failure
The set value is memorized by nonvolatile memory. Accordingly, the incubator resumes the operation
with setting before power failure.
28
KEY LOCK FUNCTION
This unit is provided with a key lock function. When the key lock is ON, change of temperature, CO2 or
O2 density setting through the key pad is not available.
Note: The key lock is set in OFF mode at the factory.
Display
Mode
Function
Key lock is OFF
Enable to change the setting
Key lock is ON
Disable to change the setting
Procedure for key lock setting (change from key lock OFF to key lock ON)
Description of operation
1
Key operated
Indication after operation
The current chamber temperature is
displayed.
----
2
Press digit shift key for 5 seconds.
L0 is displayed
in the digital temperature indicator.
3
Press numerical value shift key
and scroll the figure to 1.
When pressed, the figure of settable
digit changes.
4
Press enter key.
ENT
The key lock is set to ON.
The current chamber temperature is displayed.
Note:
• The key lock function is available for temperature, CO2 density and O2 density setting.
• To cancel the key lock, set to L0 in the above procedure.
29
AUTOMATIC GAS CYLINDER CHANGEOVER
This incubator is provided with an automatic N2 (or O2) gas cylinder changeover system, which switches
the gas (N2 or O2) cylinder when one gas cylinder becomes empty.
Also, a gas auto changer (MCO-5GC) is available as an optional accessory. This kit switches the gas
supply line when one CO2 gas cylinder becomes empty.
Note: The installation of MCO-5GC should be implemented by a qualified service personnel.
1. Indication of gas supply line currently used
Lamp ON
Lamp blink with long interval
Gas cylinder A
Gas cylinder B
Gas cylinder A
(only when MCO-5GC installed)
Gas cylinder B
(only when MCO-5GC installed)
N2/O2 gas supply line
indicator
CO2 gas supply line
indicator
CO2 gas supply line indicator
N2/O2 gas supply line indicator
2. The N2/O2 gas supply line switches when there is no change in O2 density for a while even if gas valve
is opened. Such status is regarded as the empty gas cylinder.
Similarly, CO2 gas supply line switches when one gas cylinder is empty if MCO-5GC is installed.
The notice of change of gas supply line is as follows:
Digital temperature
indicator
Digital CO2 density
indicator
Digital O2 density
indicator
When N2 or O2 gas supply
line is switched automatically
Current chamber
temperature and E02 is
displayed alternately.
Current CO2 density is
displayed.
Current O2 density
and empty cylinder is
displayed alternately
“A or B”.
When CO2 gas supply line is
switched automatically
(only when MCO-5GC is
installed)
Current chamber
temperature and E01 is
displayed alternately.
Current CO2 density
and empty cylinder is
displayed alternately
“A or B”.
Current O2 density is
displayed.
• By pressing alarm buzzer stop key (BUZZER), the alarm is canceled and the incubator returns to the
normal operation.
• Replace the cylinder A when the gas supply line is switched from cylinder A to cylinder B. Care should
be taken to the cylinder since a little gas may remain in the cylinder A.
• The supply line is switched to the cylinder A again when the cylinder B is empty.
Note:
The changeover of the gas supply line (N2 or O2 and CO2) is determined based on the recovery of CO2
and O2density in the chamber. The changeover can be accomplished by some occasions (such as block
or press of gas tube, reduction of gas pressure, or insufficient open of gas valve) even if the cylinder is
not empty. Check the gas volume remained in the cylinder before replacement.
30
3. Following shows the procedure to changeover the gas supply line (N2/O2 gas cylinder and CO2 gas
cylinder) manually.
(Example: Change of CO2 gas cylinder from B to A, Change of N2 gas cylinder from A to B)
Operation
Key
operated
Indication after operation
CO2
O2/N2
The left digit on the digital
temperature indicator blinks.
The left digit on the digital
CO2 density indicator blinks.
1
Press set key.
SET
2
Press enter key.
ENT
3
Press gas supply line
switching key once.
(Pressing the key again
selects CO2 gas cylinder B)
The blinking CO2 gas supply
lamp changes to continuous ON
and cylinder A is selected.
4
Press enter key.
The setting of CO2 gas cylinder
is memorized, and the left digit
on the digital O2 density
indicator blinks.
5
Press gas supply line
switching key once.
(Pressing the key again
selects N2 gas cylinder A)
ENT
Gas supply line
indicator
The lamp ON of N2/O2 gas
supply lamp changes to blinking
and cylinder B is selected.
6
Press enter key.
ENT
7
Press enter key.
ENT
The setting of N2 gas cylinder is
memorized. HI is displayed on
the digital CO2 density indicator
and the setting of high limit
alarm temperature is displayed.
This is the end of the setting
mode. The current chamber
temperature and densities are
displayed.
: lamp ON
Note:
The procedure 3 above should be skipped when MCO-5GC is not installed.
31
: lamp blinks
UV LAMP
The clauses below are applicable when the model is MCO-5M(UV) or an optional UV system set
MCO-19UVS is installed in MCO-5M.
A UV lamp is located inside the rear duct to sterilize the water in the humidifying pan and air circulating in
the chamber.
Following shows precautions and instructions about the UV lamp.
• The UV light is exposed only to the inside of the rear duct and the humidifying pan cover when all
chamber components are installed properly.
• During cultivation, ensure all components are located adequately and never turn on the UV light without
the humidifying pan cover.
• Even if the unit is operating without turning on the UV lamp, the humidifying pan cover should be
installed properly. An operation without humidifying pan cover will affect the temperature distribution and
humidify recovery.
• When checking the UV lamp operation, open the outer door and push the door switch with the inner
door closed. The visible blue light can be checked under the humidifying pan cover. The UV light is
harmful to eyes. Never turn on the UV light with the inner door or humidifying pan cover opened.
• The UV lamp is ON for a predetermined period after the outer door is closed, or every 12 hours when
the outer door is not opened more than 12 hours continuously. The period of factory setting is 5 minutes.
The period can be changed when necessary as shown in the page 33.
• The recommended timing of lamp replacement (the ratio of UV output is less than 70% of initial value) is
when the accumulated ON time is over about 1,000 hours. The blink of the UV indicator when the UV
lamp is OFF means the accumulated time has exceeded about 1,000 hours and recommends the
replacement of the lamp. When replacing the UV lamp, contact our sales representative or agent.
• E18 is displayed on the digital temperature indicator when the UV lamp is burned out. In this case,
replace the UV lamp immediately. At the time of replacement, also replace the glow starter (Type;
FG-7P). For the replacement of UV lamp and glow starter, contact our sales representative or agent.
32
Change of setting for UV lamp ON period
The clauses below are applicable when the model is MCO-5M(UV) or an optional UV system set
MCO-19UVS is installed in MCO-5M.
Follow the procedure below when changing the setting for UV lamp ON period.
Basic operation sequence (Example: change of UV lamp ON period from 5 minutes to 3 minutes)
Description of operation
1 Press calibration key for 5 seconds.
Key operated
CAL
4
When pressed, the changeable digit is shifted.
ENT
By pressing numerical value shift
key, set the figure to 003.
5 Press enter key.
The left digit in the digital
temperature indicator blinks.
When pressed, the figure of settable digit
changes.
By pressing numerical value shift
2 key and digit shift key,
set the figure to F01.
3 Press enter key.
Indication after operation
The current setting is displayed
in the digital CO2 density indicator.
When pressed, the figure of settable digit
changes.
ENT
Set value is memorized and the display return to
normal display mode.
• The available set range for the UV lamp is between 0 minute and 30 minutes (000 to 030). The default
setting is for 5 minutes. When set to 000, the UV lamp is not turned on.
• The UV lamp is turned off during ON period when the outer door is opened. After closing the outer
door, the lamp turns on during predetermined period.
• Condensation will occur and/or temperature distribution may be affected due to the heat of the UV lamp
when the setting of the lamp operation is longer than 5 minutes or if only the outer door is opened
repeatedly.
• For the replacement of UV lamp, contact our sales representative or agent.
Pressing calibration key (CAL) for about 5 seconds leads the calibration mode. In the calibration mode,
the calibration of temperature, CO2 density and O2 density is possible. Wrong key operation affects the
basic performance. Never touch any other keys on the control panel in the event of pressing calibration
key (CAL) accidentally. After about 90 seconds, the unit returns to chamber temperature display mode
automatically.
33
UV LAMP
Precautions when using the UV lamp
The cautions below are applicable when the model is MCO-5M(UV) or an optional UV system set
MCO-19UVS is installed in MCO-5M.
● Always use humidifying pan and humidifying pan cover
The humidifying pan and humidifying pan cover prevent the UV light from escaping. Make sure they are
installed even if you do not need humidity.
● Notice of recommended replacement of UV lamp
This unit is provided with a function to notify the recommendation of UV lamp replacement when the
accumulated ON time of UV lamp is over about 1,000 hours. The blink of the UV indicator on the control
panel recommends the replacement of UV lamp. For the replacement, contact our sales representative
or agent.
● Location of UV lamp
The UV lamp is OFF when the outer door is opened as it is operated to outer door switch. Check the UV
lamp is ON with the inner door closed once a month by activating the outer door switch. If the lamp is
not ON, the lamp needs to be replaced. Contact our sales representative or agent.
The UV lamp is located in the rear duct. Take care not to damage the lamp at the time of
installation/removal of attachments or humidifying pan.
WARNING
Never expose the eyes directly to UV light as UV light can cause permanent damage to eyes. Never
remove humidifying pan cover when UV light is ON (MCO-5M(UV) or when an optional UV system set
MCO-19UVS is installed in MCO-5M).
Hazardous UV light. Do not press door switch.
34
Lighting the UV lamp for 24 hours
Follow the procedure below when lighting UV lamp for 24 hours.
Before sterilization by UV lamp, remove all attachments in the chamber (tray, side support, rear duct, fan,
humidifying pan, humidifying pan cover, gas injection nozzle, gas injection nozzle tube) and clean the
interior, inner door and UV lamp thoroughly.
Description of operation
1
Press calibration key
for 5 seconds.
2
By pressing numerical value shift
key and digit shift key,
set the figure to F02.
3
Press enter key.
4
By pressing numerical value shift
key, set the figure to 001.
5
Press enter key.
Key operated
Indication after operation
The left digit in the digital
temperature indicator blinks.
CAL
When pressed, the figure of settable digit changes.
When pressed, the changeable digit
is shifted.
ENT
“000” is displayed in the digital
CO2 density indicator. (unit: min)
When pressed, the figure of
settable digit changes.
ENT
Set value is memorized and the display returns to
normal display mode.
● This setting should be executed with the outer door closed and the UV lamp off.
● The UV lamp keeps on for 24 hours after the setting. The setting is canceled when the outer door is
opened. Follow the above procedure to set the UV 24-hour mode again.
● The unit keeps running with set temperature, CO2 density and O2 density during UV lighting.
Pressing calibration key (CAL) for about 5 seconds leads the calibration mode. In the calibration mode,
the calibration of temperature, CO2 density and O2 density is possible. Wrong key operation affects the
basic performance. After about 90 seconds, the unit returns to chamber temperature display mode
automatically. In this case, the set value that has not been fixed pushing enter key (ENT) is not
changed.
35
ALARMS, SAFETY AND SELF-DIAGNOSIS
This unit has the alarms and safety functions shown in table below, and also self diagnostic functions.
Alarms and safety functions
Alarm &amp; Safety
Situation
High limit
temperature alarm
Automatic set
temperature alarm
Indication
If the chamber temperature exceeds
the high limit alarm temperature set
value.
Buzzer
Safety operation
Over heat lamp lights.
E12 or E16 and chamber
temperature are displayed
Continuous tone
Heater OFF
Remote alarm
alternately.
If the chamber temperature deviates
o
from the set temperature by &plusmn;1 C or
more.
All digits on the digital
Intermittent tone with
Remote alarm with 15
temperature indicator blink.
15 minutes delay.
minutes delay
Remote alarm with 15
Automatic set CO2
If the chamber CO2 density deviates
All digits on the digital CO2
Intermittent tone with
density alarm
from the set value by &plusmn;1 % or more.
density indicator blink.
15 minutes delay.
minutes delay
Automatic set O2
If the chamber O2 density deviates
All digits on the digital O2
Intermittent tone with
Remote alarm with 30
density alarm
from the set value by &plusmn;1 % or more.
density indicator blink.
30 minutes delay.
minutes delay
Auto-return
When there is no key pressing in
each setting mode for 90 seconds.
Key lock
When the key lock is “ON”.
CO2 gas cylinder
If the CO2 density does not increase
empty
when the CO2 gas valve is opened.
N2/O2 gas cylinder
If the O2 density does not change
empty
when the N2/O2 gas valve is opened.
Normal display mode.
-----
---------
The setting mode is
canceled.
The setting is disabled.
E01 is displayed alternately
with the temperature on the
Intermittent tone
Remote alarm
digital temperature indicator.
E02 is displayed alternately
with the temperature on the
Remote alarm
Intermittent tone
N2/O2 gas supply line is
altered
digital temperature indicator.
E01 is displayed alternately
CO2 gas line
changeover
When the CO2 gas supply line is
switched.
(only when MCO-5GC is installed)
with the temperature on the
digital temperature indicator.
The empty gas supply line
Remote alarm
Intermittent tone
Gas supply line is
altered.
is displayed on the digital
CO2 density indicator.
E02 is displayed alternately
with the temperature on the
O2/N2 gas line
When the O2/N2 gas supply line is digital temperature indicator.
changeover
switched.
The empty gas supply line
Remote alarm
Intermittent tone
Gas supply line is
altered.
is displayed on the digital
O2 density indicator.
Wrong CO2 gas line
If the CO2 gas is connected to wrong
connection
gas supply line.
Wrong selection of
gas between N2 and
O2
If the N2 gas or O2 gas is selected
wrongly.
If the temperature sensor is
Chamber
disconnected.
temperature sensor
abnormality
If the temperature sensor is short
circuited.
E03 is displayed alternately
with the temperature on the
Remote alarm
Intermittent tone
E04 is displayed alternately
with the temperature on the
N2/O2 valve and CO2
valve are closed.
digital temperature indicator.
Remote alarm
Intermittent tone
N2/O2 valve and CO2
valve are closed.
digital temperature indicator.
E05 is displayed alternately
with the temperature on the
digital temperature indicator.
E06 is displayed alternately
with the temperature on the
digital temperature indicator.
36
Intermittent tone
Heater OFF
Remote alarm
Alarms and safety functions
Alarm &amp; Safety
Situation
If the ambient temperature sensor is
Ambient
disconnected.
temperature sensor
abnormality
If the ambient temperature sensor is
short circuited.
CO2 sensor
If the output voltage of the CO2 sensor
abnormality
is abnormal.
O2 sensor
If the output voltage of the O2 sensor
abnormality
is abnormal.
If the high limit alarm temperature
Main heater
alarm operates, or if the main heater is
abnormality
open circuit, or the main heater relay
is short circuited.
Indication
with the temperature on the
digital temperature indicator.
E10 is displayed alternately
with the temperature on the
Intermittent tone
digital temperature indicator.
E19 is displayed alternately
with the temperature on the
Intermittent tone
digital temperature indicator.
CO2 valve closes.
Remote alarm
N2/O2 valve closes.
Remote alarm
E12 is displayed alternately
with the temperature on the
Intermittent tone
Remote alarm
Intermittent tone
Remote alarm
Intermittent tone
Remote alarm
Intermittent tone
Remote alarm
digital temperature indicator.
with the temperature on the
short circuited.
digital temperature indicator.
If the door heater goes open circuit,
E14 is displayed alternately
or the door heater relay is
with the temperature on the
short circuited.
digital temperature indicator.
Disconnection of
If the relay of main heater, bottom
E16 is displayed alternately
S.S.R for each
heater or sensor box heater goes open with the temperature on the
heater
circuit.
Low humidifying
If the water in the humidifying pan is Water level alarm lamp
water
about 0.8 L.
(RH PAN) blinks.
[MCO-5M(UV) or when
MCO-19UVS is installed in MCO-5M]
When the UV lamp is burned out.
E18 is displayed alternately
UV lamp failure
abnormality
Remote alarm
digital temperature indicator.
E11 is displayed alternately
E13 is displayed alternately
Door heater
Intermittent tone
with the temperature on the
or the bottom heater relay is
abnormality
Safety operation
E09 is displayed alternately
If the bottom heater goes open circuit,
Bottom heater
Buzzer
digital temperature indicator.
with the temperature on the
-----
Intermittent tone
-----
Remote alarm
digital temperature indicator.
[MCO-5M(UV) or when
Recommendation of MCO-19UVS is installed In MCO-5M]
UV indicator blinks
The accumulated ON time is over when UV lamp is OFF.
new UV lamp
about 1,000 hours.
-----
-----
• The alarm can be canceled by pressing the alarm buzzer stop key (BUZZER), but the remote alarm
cannot be silenced. And the high limit temperature alarm cannot be silenced with the alarm buzzer stop
key (BUZZER).
• E01 or E02 is cleared automatically when the gas is connected correctly and the buzzer is silenced with
the alarm buzzer stop key (BUZZER). Press the alarm buzzer stop key (BUZZER) to silence the alarm
after changeover of gas supply line.
• If one of E05 to E18 is displayed, consult with our sales representative or agent.
37
CALIBRATION
Temperature calibration
1. Press the calibration key (CAL) for approximately 5 seconds.
2. The left digit of the digital temperature indicator blinks, and the other indicators go out.
3. Set the present correct temperature with the digit shift key (
) and numerical value shift key (
then press the enter key (ENT).
4. The unit automatically reverts to the display mode.
),
[Example]
If the displayed chamber temperature is 37.0 oC (set value) and the actual temperature is 36.8 oC.
1. Press the calibration key (CAL) for about 5 seconds.
2. The “3” on the digital temperature indicator blinks, and the other indicators go out.
3. Adjust the set value to the actual value of 36.8 oC with the digit shift key (
) and numerical value
shift key ( ), then press enter key (ENT).
4. The unit automatically reverts to the display mode.
Note:
It is important to accurately measure the temperature inside the unit when performing temperature
calibration. Particularly, the temperature gauge used must have an accuracy of 0.5 class or better.
The temperature must be measured at several points.
The temperature setting must not change by more than &plusmn;1.0 oC during calibration. If it exceeds this, an
error tone is emitted, the input data is ignored, and the unit reverts to the display mode. Consequently, if
it is necessary to change the temperature by more than 1.0 oC, perform calibration in several stages over
a period of time.
38
O2 calibration
[Zero setting]
Zero setting should be done when CO2 and O2/N2 has not been injected yet and the stable condition
(about 8 hours) of temperature/humidity inside the unit has been attained.
1. Press the calibration key (CAL) for 5 seconds.
2. The left digit on the digital temperature indicator blinks, and the other indicators go out.
3. Press the calibration key (CAL) once again.
4. The left digit on the digital CO2 density indicator blinks, and the other indicators go out.
5. Press the calibration key (CAL) once again.
6. The left digit of the digital O2 density indicator blinks, and the other indicators go out.
7. Set 20.0 with the digit shift key (
) and numerical value shift key ( ), then press the enter key
(ENT).
8. The unit automatically reverts to the display mode.
[Span setting]
Span setting should be done under stable condition of temperature, humidity, CO2 and O2 density.
1. Press the calibration key (CAL) for about 5 seconds.
2. The left digit of the digital temperature indicator blinks, and the other indicators go out.
3. Press the calibration key (CAL) once again.
4. The left digit of the digital CO2 density indicator blinks, and the other indicators go out.
5. Press the calibration key (CAL) once again.
6. The left digit of the digital O2 density indicator blinks, and the other indicators go out.
7. Set the present correct O2 density with the digit shift key (
) and numerical value shift key (
then press the enter key (ENT).
8. The unit will automatically revert to the display mode.
),
[Example]
For the internal O2 density of 5.0 % (setting) and a measured value is 4.8 %.
1. Press the calibration key (CAL) for about 5 seconds.
2. The left digit on the digital temperature indicator blinks, and the other indicators go out.
3. Press the calibration key (CAL) once again.
4. The left digit on the digital CO2 density indicator blinks, and the other indicators go out.
5. Press the calibration key (CAL) once again.
6. The left digit of the digital O2 density indicator blinks, and the other indicators go out.
7. Set the present correct O2 density (4.8 %) with the digit shift key (
) and numerical value shift key
( ), then press the enter key (ENT).
8. The unit automatically reverts to the display mode.
Note:
•The calibration is applicable when the set value and present value are less than 15 % or more than 25 %
O2 density.
•The separate calibration is needed as the low density (less than 15 %) and high density (more than
25 %) has the span calibrating value respectively.
•Always carry out the CO2 calibration after O2 calibrating ( [ZERO],[SPAN] ).
39
CALIBRATION
CO2 calibration
[Zero setting]
Zero setting should be done when CO2 and O2/N2 has not been injected yet and the stable condition
(about 8 hours) of temperature/humidity inside the unit has been attained.
1. Press the calibration key (CAL) for 5 seconds.
2. The left digit on the digital temperature indicator blinks, and the other indicators go out.
3. Press the calibration key (CAL) once again.
4. The left digit on the digital CO2 density indicator blinks, and the other indicators go out.
5. Set 00.0 with the digit shift key (
) and numerical value shift key ( ), then press the enter key
(ENT).
6. The unit automatically reverts to the display mode.
[Span setting]
Span setting should be done under stable condition of temperature, humidity, and CO2 density.
1. Press the calibration key (CAL) for about 5 seconds.
2. The left digit on the digital temperature indicator blinks, and the other indicators go out.
3. Press the calibration key (CAL) once again.
4. The left digit on the digital CO2 density indicator blinks, and the other indicators go out.
5. Set the present correct CO2 density with the digit shift key (
) and numerical value shift key (
then press the enter key (ENT).
6. The unit automatically reverts to the display mode.
),
Note:
This calibration is available when the present correct CO2 density is 2 % or more.
[Example]
For an internal CO2 density of 5.0 % (setting) and a measured value of 4.5 %.
1. Press the calibration key (CAL) for about 5 seconds.
2. The left digit on the digital temperature indicator blinks, and the other indicators go out.
3. Press the calibration key (CAL) once again.
4. The left digit on the digital CO2 density indicator blinks, and the other indicators go out.
5. Set the present correct CO2 density (4.5 %) with the digit shift key (
) and numerical value shift key
( ), then press the enter key (ENT).
6. The unit automatically reverts to the display mode.
40
TROUBLESHOOTING
If the unit malfunctions, check out the following before calling for service.
Malfunction
The unit does not operate
at all
The key
disabled
operation
is
If the alarm function
operates
If the chamber
temperature is not
equal to the set
temperature
If the gas density does not
coincide with the set value
If the chamber humidity
does not rise
If the gas consumption is
too much
Check/Remedy
• The unit is not plugged correctly into a power outlet.
• The circuit breaker at the power source is active or a power failure
has occurred.
• The removal power supply cord is connected to the port attached on
the rear of the cabinet.
• The key lock function is set in ON mode.
[At the beginning of operation]
• The chamber temperature is not equal to the set value.
• The chamber CO2/O2 density is not equal to the set value.
a. The secondary pressure of the gas regulator is not equal to the
set value [for CO2 gas; 0.03 MPa(G) (0.3 kgf/cm2(G), 4.3 psi(G)),
for N2/O2 gas; 0.05 MPa(G) (0.5 kgf/cm2(G), 7.1 psi(G))].
b. The gas tube is not connected securely between the gas
regulator and the unit.
[During operation]
• The high limit alarm temperature is not set at least 1 oC higher than
the set chamber temperature.
• The set temperature value was changed, or the door was left open
for a long period. Or a low temperature load was placed inside the
unit. In this case, if the unit is left as it is, the alarm will eventually
clear itself.
• The gas tube has slipped off or the gas leaks.
• The set value of the gas density was changed.
• The gas cylinder is empty. Check the primary pressure of the gas
cylinder once a week. (The CO2 primary pressure of less than 3.8
MPa(G) (38 kgf/cm2(G), 551 psi(G)) means a little gas in the cylinder.
Replace the cylinder soon.)
• The ambient temperature must always be at least 5 oC less than the
set temperature.
• The outer door was closed while the inner door was left open.
• The secondary pressure is not set to the specified value [for CO2 gas;
0.03 MPa(G) (0.3 kgf/cm2(G), 4.3 psi(G)), for N2/O2 gas; 0.05 MPa(G)
(0.5 kgf/cm2(G), 7.1 psi(G))].
• The gas tube is clogged or chinked.
• The humidifying pan is not filled with sterile distilled water. (Always
use sterile distilled water.)
• The humidifying pan is not filled with sterile distilled water. (Always
use sterile distilled water.)
• The door is opened frequently.
• There is any gas leakage at the connection or pin hole on the gas
tube. It is recommended to replace the gas tube once a year.
• The gasket of the inner door is not completely sealed.
• The access port at the upper left corner is opened.
41
TROUBLESHOOTING
Malfunction
If normal cultivation cannot
be done and chamber gas
density is suspect
If it takes much time to
recover the gas density
Check/Remedy
• The environment around the unit is not normal. The source of the
contaminated gas is nearby.
• The unit is installed in an enclosed space.
• HEPA filter is provided in the gas piping. If it takes much time to
recover the gas density even though the gas pressure is normal, it may
be that dust on the HEPA filter prevents the gas flow. Consult the our
sales representative or agent.
Note:
If the malfunction is not eliminated after checking the above items, or the malfunction is not shown in the
above table, contact our sales representative or agent.
42
DISPOSING OF THE O2/CO2 INCUBATOR
When disposing of the O2/CO2 incubator, contact our sales representative or agent.
WARNING
The O2/CO2 incubator must be dismantled and disposed of by qualified personnel only. If the
incubator is left where outsiders enter, it may result unexpected accident (for example, children to become
locked inside).
Before disposing a O2/CO2 incubator with biohazardous danger, decontaminate the O2/CO2 incubator to
the extent possible by the user.
43
DISPOSING OF THE O2/CO2 INCUBATOR
Note:
This symbol mark and recycle system apply only to EU countries. They
do not applied to the countries in other areas of the world.
Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC
(English)
This Panasonic product is designed and manufactured with high-quality materials and components that
can be recycled and reused.
This symbol means that the electrical and electronic equipment, at their end-of-life, should be disposed of
separately from household wastes.
Dispose of this product at your local community waste collection/recycling center.
In the European Union there are separate collection systems for used electrical and electronic products.
Please help us to conserve the environment we live in.
(German)
Ihr Panasonic Produkt wurde entworfen und hergestellt mit qualitativ hochwertigen Materialien und
Komponenten, die recycelt und wiederverwendet werden k&ouml;nnen.
Dieses Symbol bedeutet, da&szlig; elektrische und elektronische Ger&auml;te am Ende ihrer Nutzungsdauer von
Hausm&uuml;ll getrennt entsorgt werden sollen.
Bitte entsorgen Sie dieses Ger&auml;t bei Ihrer &ouml;rtlichen kommunalen Sammelstelle oder im Recycling Centre.
In der Europ&auml;ischen Union gibt es unterschiedliche Sammelsysteme f&uuml;r Elektrik- und Elektronikger&auml;te.
Helfen Sie uns bitte, die Umwelt zu erhalten, in der wir leben!
44
(French)
Votre produit Panasonic est con&ccedil;u et fabriqu&eacute; avec des mat&egrave;riels et des composants de qualit&eacute; sup&eacute;rieure
qui peuvent &ecirc;tre recycl&eacute;s et r&eacute;utilis&eacute;s.
Ce symbole signifie que les &eacute;quipements &eacute;lectriques et &eacute;lectroniques en fin de vie doivent &ecirc;tre &eacute;limin&eacute;s
s&eacute;par&eacute;ment des ordures m&eacute;nag&egrave;res.
Nous vous prions donc de confier cet &eacute;quipement &agrave; votre centre local de collecte/recyclage.
Dans l’Union Europ&eacute;enne, il existe des syst&egrave;mes s&eacute;lectifs de collecte pour les produits &eacute;lectriques et
&eacute;lectroniques usag&eacute;s.
Aidez-nous &agrave; conserver l’environnement dans lequel nous vivons !
Les machines ou appareils &eacute;lectriques et &eacute;lectroniques contiennent fr&eacute;quemment des mati&egrave;res qui, si elles
sont trait&eacute;es ou &eacute;limin&eacute;es de mani&egrave;re inappropri&eacute;e, peuvent s’av&eacute;rer potentiellement dangereuses pour la
sant&eacute; humaine et pour l’environnement.
Cependant, ces mati&egrave;res sont n&eacute;cessaires au bon fonctionnement de votre appareil ou de votre machine.
Pour cette raison, il vous est demand&eacute; de ne pas vous d&eacute;barrasser de votre appareil ou machine usag&eacute;
avec vos ordures m&eacute;nag&egrave;res.
(Spanish)
Los productos Panasonic est&aacute;n dise&ntilde;ados y fabricados con materiales y componentes de alta calidad,
que pueden ser reciclados y reutilizados.
Este s&iacute;mbolo significa que el equipo el&eacute;ctrico y electr&oacute;nico, al final de su ciclo de vida, no se debe
desechar con el resto de residuos dom&eacute;sticos.
Por favor, deposite su viejo “televisor” en el punto de recogida de residuos o contacte con su
administraci&oacute;n local.
En la Uni&oacute;n Europea existen sistemas de recogida espec&iacute;ficos para residuos de aparatos el&eacute;ctricos y
electr&oacute;nicos.
Por favor, ay&uacute;denos a conservar el medio ambiente!
45
DISPOSING OF THE O2/CO2 INCUBATOR
(Portuguese)
O seu produto Panasonic foi concebido e produzido com materiais e componentes de alta qualidade que
podem ser reciclados e reutilizados.
Este s&iacute;mbolo significa que o equipamento el&eacute;ctrico e electr&oacute;nico no final da sua vida &uacute;til dever&aacute; ser
descartado separadamente do seu lixo dom&eacute;stico.
Por favor, entregue este equipamento no seu ponto local de recolha/reciclagem.
Na Uni&atilde;o Europeia existem sistemas de recolha separados para produtos el&eacute;ctricos e electr&oacute;nicos
usados.
Por favor, ajude-nos a conservar o ambiente em que vivemos!
(Italian)
Il vostro prodotto Panasonic &egrave; stato costruito da materiali e componenti di alta qualit&agrave;, che sono
riutilizzabili o riciclabili.
Prodotti elettrici ed elettronici portando questo simbolo alla fine dell’uso devono essere smaltiti
separatamente dai rifiuti casalinghi.
Vi preghiamo di smaltire questo apparecchio al deposito comunale.
Nell’Unione Europea esistono sistemi di raccolta differenziata per prodotti elettrici ed elettronici.
Aiutateci a conservare l’ambiente in cui viviamo!
46
(Dutch)
Panasonic producten zijn ontwikkeld en gefabriceerd uit eerste kwaliteit materialen, de onderdelen kunnen
worden gerecycled en weer worden gebruikt.
Het symbool betekent dat de elektrische en elektronische onderdelen wanneer deze vernietigd gaan
worden , dit separaat gebeurt van het normale huisafval.
Zorg ervoor dat het verwijderen van de apparatuur bij de lokaal erkende instanties gaat gebeuren.
In de Europese Unie wordt de gebruikte elektrische en elektronische apparatuur bij de daarvoor wettelijke
instanties aangeboden.
Alstublieft help allen mee om het milieu te beschermen.
(Swedish)
Din Panasonic produkt &auml;r designad och tillverkad av material och komponenter med h&ouml;g kvalitet som kan
&aring;tervinnas och &aring;teranv&auml;ndas.
Denna symbol betyder att elektriska och elektroniska produkter, efter slutanv&auml;ndande, skall sorteras och
l&auml;mnas separat fr&aring;n Ditt hush&aring;llsavfall.
V&auml;nligen, l&auml;mna denna produkt hos Din lokala mottagningstation f&ouml;r avfall/&aring;tervinningsstation.
Inom den Europeiska Unionen finns det separata &aring;tervinningssystem f&ouml;r begagnade elektriska och
elektroniska produkter.
V&auml;nligen, hj&auml;lp oss att bevara milj&ouml;n vi lever i!
47
STACKING INCUBATORS
Use the following procedure to stack incubators. This work is potentially dangerous, so contact our sales
representative or agent.
CAUTION
 Select a floor that is strong enough to support the stacked incubators.
 Never stack 4 or more incubators. Doing so is dangerous.
(When stacking 2 incubators)
1. Take out 2 stacking plates A, 2 stacking plates B, 4 protective stickers, and 4 screws from accessory
bag.
Note:
Use 2 stacking plates (A and B) for each one. Only one pair of stacking plates is provided per an
incubator, so take out the stacking plates (A and B) from both incubators.
2. Unplug both of the incubators that are to be stacked.
3. Remove the caps at the 2 places in the front of the top surface of the incubator that is to be on the
bottom, attach the protective stickers to the 4 corners on the top surface of the incubator that is to be on
the bottom. (Fig. A)
4. Secure stacking plate A with the screws that are provided.
5. Remove the front panel (4 screws, 3 connectors, 1 ground wire, 1 gas tube) from the incubator that is
to be on the top.
6. Place the upper incubator on top of the lower one, being careful not to pinch your fingers.
7. Make the lower incubator level by adjusting the leveling feet, and then level the upper incubator in the
same way.
8. Secure the stacking plate A fixed to the lower incubator to the upper incubator with the accessory
screws.
9. Remove from the back of the lower incubator the 2 hooks (4 screws) and remove from the upper
incubator the 2 screws on the lower rear panel.
10. Use the 6 screws that were removed in step 9 to secure stacking plate B to the rear panels of the
upper and lower incubators.
11. Replace the front panel (4 screws, 3 connectors, 1 ground wire, 1 gas tube) to the upper incubator.
12. Use the hooks on the back of the upper incubator to prevent the incubators from falling over.
(When stacking 3 incubators)
13. Perform again the procedure from step 3
48
Front panel
Stacking plate B
Stacking plate A
Protective sticker
Fig.A ＜View from quarter rear side＞
49
SPECIFICATIONS
Product name
O2/CO2 Incubator MCO-5M
O2/CO2 Incubator MCO-5M(UV)
External dimensions
W480 mm x D548 mm x H575 mm (W18.9 inch x D21.6 inch x H22.6 inch)
Internal dimensions
W350 mm x D378 mm x H375 mm (W13.8 inch x D14.9 inch x H14.8 inch)
Interior volume
49 L (1.73 cu.ft.)
Exterior
Painted steel
Interior
Stainless steel containing copper (R corner structure)
Outer door
Painted steel,
Reversible support (selectable right or left-hand door)
Inner door
Tempered glass
Trays
Access port
Made of stainless steel containing copper (standard 3 trays , maximum 6 trays )
W310 mm x D310 mm x H12 mm (W12.2 inch x D12.2 inch x H0.47 inch)
Maximum load; 4 kg/tray
Inner diameter; 30 mm (1.18 inch), On the back side
Insulation
Rigid polyurethane foamed-in place
Heating system
Direct Heat &amp; Air (DHA) jacket system
Heater
180 W
Humidifying system
Natural evaporation with humidifying pan
Temperature controller
PID control system
Temperature display
Digital display
CO2 controller
PID control system/TC sensor(direct detection in chamber)
CO2 density display
O2 controller
Digital display
PID control system/Zirconia sensor(direct detection in chamber)
O2 density display
Digital display
Air circulation
Fan assisted
Air filter
UV lamp
0.3 μm, Efficiency; 99.97 % or higher
-----
4 W x 1 (ozone-free emission)
Water level sensor
Alarms
Remote alarm contacts
Gas inlet connection
Optical type
Automatic set temperature alarm, Automatic set CO2 density alarm
Automatic set O2 density alarm, High limit temperature alarm
Various gas/sensor/heater alarms
Allowable contact capacity: DC 30 V, 2 A
4 mm to 6 mm (0.157 inch to 0.236 inch) diameter tube can be connected
CO2 inlet pressure
0.03 MPa(G) (0.3 kgf/cm2(G), 4.3 psi(G))
O2 inlet pressure
0.05 MPa(G) (0.5 kgf/cm2(G), 7.1 psi(G))
Accessories
1 removal power supply cord ,3 trays, 3 gas tube, 1 humidifying pan
1 gas injection nozzle, 1 gas injection nozzle tube
1 pair of stacking plates A and B, 4 protective stickers, 6 tube bands
50 kg
Weight
Optional accessories
UV system set (MCO-19UVS)
UV system set is a standard equipment.
Gas auto changer (MCO-5GC), Gas regulator (MCO-100L)
Tray (MCO-30ST), Roller base (MCO-5RB)
Interface board (MTR-L03), Interface board (MTR-480)
Data acquisition system (MTR-5000), Interface board (MCO-420MA, USA only)
Note: Refer to the updated catalog when ordering an optional component.
Designs and specifications are subject to change without notice.
50
PERFORMANCE
O2/CO2 Incubator MCO-5M
MCO-5M(UV)
MCO-5M-PK
MCO-5M-PE
MCO-5MUV-PK
MCO-5MUV-PE
Product name
Model No.
MCO-5M-PA
MCO-5MUV-PA
Temperature control range
Ambient temperature +5 oC to 50 oC (ambient temperature; 5 oC to 35 oC)
Temperature distribution
&plusmn;0.25 oC (ambient temperature; 25 oC, setting; 37 oC, CO2: 5 %, O2: 5 %, no load)
Temperature variation
&plusmn;0.1 oC (ambient temperature; 25 oC, setting; 37 oC, CO2: 5 %, O2: 5 %, no load)
CO2 control range
CO2 variation
0 % to 20%
&plusmn;0.15 % (ambient temperature; 25 oC, setting; 37 oC, CO2: 5 %, O2: 5 %, no load)
O2 control range
O2 variation
1 % to 18 %, 22 % to 80%
&plusmn;0.2 % (ambient temperature; 25 oC, setting; 37 oC, CO2: 5 %, O2: 5 %, no load)
Chamber humidity
95 %R.H.&plusmn; 5 %R.H.
o
Applicable environment
condition
Temperature; 5 C to 35 oC, Humidity; equal or less than 80 %R.H.
(The designed performance may not be obtained when
the ambient temperature is equal or less than 15 oC)
Noise level
24 dB (A scale)
Power consumption
Max. 205 W
Heat emission
Related voltage, frequency
Amperage
Max. 740 kJ/h
110 V to 120 V, 60 Hz
220 V, 60 Hz
220 V to 240 V, 50 Hz
Max. 1.8 A
Max. 0.9 A
Max. 0.9 A
Note: The unit with CE mark complies with EC directives.
Based on our measuring method.
51
CAUTION
Please fill in this form before servicing.
Hand over this form to the service engineer to keep for his and your safety.
Safety check sheet
1. Unit contents
Risk of infection:
Risk of toxicity:
Risk from radioactive sources:
□Yes
□Yes
□Yes
□No
□No
□No
(List all potentially hazardous materials that have been stored in this unit.)
Notes :
2. Contamination of the unit
Unit interior
No contamination
Decontaminated
Contaminated
Others:
□Yes
□Yes
□No
□No
□Yes
□No
3. Instructions for safe repair/maintenance of the unit
□Yes
□No
a) The unit is safe to work on
b) There is some danger (see below)
□Yes
□No
Procedure to be adhered to in order to reduce safety risk indicated in b) below.
Date :
Signature :
Address, Division :
Telephone :
Product name :
O2/CO2 incubator
Model No.
Serial number :
MCO-
Please decontaminate the unit yourself before calling the service engineer.
52
Date of Installation :
1-1-1, Sakata Oizumi-Machi Ora-Gun, Gunma 370-0596, Japan
&copy; Panasonic Healthcare Co., Ltd. 2012
Printed in Japan
7FB6P15139800
S0412-1042
">

Hello! I am an AI chatbot specifically trained to assist you with the Panasonic MCO-5M (UV), UV O2/CO2 Incubator Operating Instructions. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant terminated

Key Features

Precise Temperature Control
CO2 Density Control
O2 Density Control
UV Sterilization (MCO-5M(UV) & MCO-5MUV)
Humidity Control
Automatic Gas Cylinder Changeover
Alarm System
Safety Features
Easy to Use Interface

Frequently asked questions

What is the difference between the MCO-5M, MCO-5M(UV), and MCO-5MUV models?

The MCO-5M(UV) and MCO-5MUV models include a built-in UV lamp for chamber sterilization, while the MCO-5M does not.

How do I set the temperature, CO2, and O2 levels in the incubator?

You can adjust these settings using the control panel and keypad. Refer to the operating instructions for detailed information on setting parameters.

What kind of water should I use in the humidifying pan?

Always use sterile distilled water. Do not use ultrapure water, as it may cause rust particles to form.

What is the difference between the MCO-5M, MCO-5M(UV), and MCO-5MUV models?

How do I set the temperature, CO2, and O2 levels in the incubator?

What kind of water should I use in the humidifying pan?

Related

Phcbi MCO-5M Series, MCO-5M-PA Operating instructions

PHCbi MCO-170AC-PE MCO CO2 Incubator Operating Instructions

Panasonic MDF-U4186S Series Ultra-Low Temperature Freezer Operating Instructions

Sanyo MCO-19M Incubator Instruction Manual

Sanyo CO2 Incubator MCO-19AIC Manual

Panasonic MCO-19M Series Incubator Operating Instructions

Sanyo MCO-5M Instruction Manual

Sanyo MCO-19M(UV) Service Manual - Multi-Gas Incubator

SANYO MCO-20AIC CO2 Incubator Instruction Manual

Phcbi MIR-H263-PA, MIR-H263-PR Operating instructions

Panasonic MCO-170AICUVL Operating Instructions Manual

Panasonic MCO-20AIC CO2 Incubator Operating Instructions