Manual - Sign in to My Account
Remote with Voice Control
1 Meet Your Remote
2 Turn On Your Remote
Your remote arrives with the AA batteries
already installed, but not activated. Here is
how to power it on for the first time.
TV Power
3 Pair Remote for “Aim
Anywhere” Control
Control your set-top box without having to
point your remote at the device, even
when it is located inside a cabinet or
entertainment center.
Status LED
All Power
A Pick up your remote and remove the “Pull”
tab (on back) by pulling away from the
remote. The Status LED will blink green
four times as the remote powers up (about
5 seconds).
A Press and hold the Setup button (about 3
seconds) until the Status LED changes
from red to green.
Voice Control
Push and hold to talk. Discover content
by channel, program or key words.
Access Guide, Saved, XFINITY On Demand,
Apps, Search and Settings.
B Turn on your TV.
C Turn on your set-top box.
B Press the XFINITY button.
C Follow the on-screen instructions to enter
the 3-digit code that appears.
Once the code is correctly entered, your
XFINITY Remote is paired with the device.
Number Keys
Use predictive text (T9) to quickly search
for content.
TV Input
Changes to the next available input on
your TV (if programmed in Step 4).
Program remote for Aim Anywhere or
to control your TV or audio device.
Not working? Make sure the battery tab from
your remote is removed, your TV is on and you are
entering the correct 3-digit code on your TV screen.
Need to remove Aim Anywhere control? Press
and hold the Setup button on the remote until the
status LED changes from red to green. Press A on
the remote. If the status LED blinks green twice,
you have successfully removed Aim Anywhere.
4 Control Your TV’s Power and Volume
5 Test Voice Control
Once your remote is paired with your set-top
box, you can use voice control.
A Using the list on the right, find the first 5digit code for your TV manufacturer.
B Press and hold the Setup button (about 3
seconds) until the Status LED changes
from red to green.
Need help ?
Use the My Account app
for Mobile (iOS/Android) or X1
C Enter the first 5-digit code for your TV
manufacturer. The Status LED should flash
green twice.
Popular Manufacturer Codes
10178, 11265
10051, 10250
10812, 10060
10154, 10159
10000, 11100
Sharp 10093, 10165
10156, 11156
11758, 11756
If your code isn’t listed or you would
like to control an audio device, visit
Remote with Voice Control
A Press and hold the Voice button until you
hear the audio tone.
B Speak a voice command to the remote
while continuing to hold down the button.
Try one of the suggestions below. The
Status LED will be solid blue while you
speak your command.
SHOW ME all Eagles games
SHOW ME all kids movies on HBO
RECORD The Biggest Loser
LAUNCH Pandora
C Release the Voice button when your
command is complete. Look at the TV for
the results of your voice command.
Keep for future reference, but if you
decide to toss, please recycle.
Quick Start Guide v.1.0
1698397C Printed in China
There is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, the user is
encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase or decrease the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that which the receiver is connected.
Consult the dealer or an experienced remote control
/TV technician for help.
• It is strongly recommended that the TV be plugged into a separate wall outlet.
FIND The Voice
D Verify that the code was accepted by using
your remote to adjust volume and turn the
TV on and off.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15
of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not used
in accordance with the instructions, may cause harmful
interference to radio communications.
Not working? Try the second code listed. Still
not working? Visit for a
complete list of codes or use the My Account app
for mobile (iOS/Android) or X1.
FCC Compliance Statement
Not working? Make sure you’re pressing the
Voice button while you speak into the remote,
and release it when complete.
The user is cautioned that changes and modifications made
to this equipment without the approval of the manufacturer
could void the user’s authority to operate this equipment.
This device complies with part 15 of the FCC rules. Operation
is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
“Caution” : Exposure to Radio Frequency Radiation. Antenna
shall be mounted in such a manner to minimize the potential
for human contact during operation to avoid the possibility of
exceeding the FCC radio frequency exposure limit.
Radio Exposure Statement: This equipment complies with
the FCC radiation exposure limits set forth for devices
operating in an uncontrolled environment. This equipment
should be operated with a minimum distance of 2 cm
between the radiator and front of face. This equipment
should not be placed directly on the ear when the speaker
is active.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF