RCGF 26ccBM Operator's Manual - RCGF engines

RCGF 26ccBM Operator's Manual - RCGF engines
RCGF 26ccBM Operator’s Manual
(note: the spare parts list and dimension of engine are in the end of manual)
RCGF 26cc BM
Type : 2 cycle piston valve type gasoline engine for airplane
Piston displacement Cylinder (cc) : 26cc (1.60cu.in)
Bore x Stroke (mm): 1. 3 in(34mm) x 1.0 in(26mm)
Carburetor : RCGF
Ignition : RCGF DC-CDI (Computer Controlled auto advance, electronic ignition system)
Power supply: 4.8-8.4V
Maximum Output : 2.95HP /2.2KW
Requires: Gasoline, 2-cycle oil, ignition battery & propeller
Speed rang : 1500-9800rpm
Gasoline-Version : Pre-mixed Fuel, 25-40 (Gasoline):1 , Recommend:30:1
(90% high otcane unleaded gasoline, Import gas into carbon fiber installations valves)
Lubrication Oil : 2 cycle engine oil
Propeller : 18X8 7000rpm (Standard Two leafs prop)
Suggested Propellers:16X8,16X10, 17X8,17X10,18x8, 18x10
Sparking plug: NGK CM6 Type
Cooling System : Air Cooled
RCGF engine package Includes: electronic CDI ignition, muffler, spark plug, gaskets,
bolts, throttle arm extension & manual.
Weight :
Engine: 1.65 lb (748 g)
Muffler: 2.5 oz (70g)
Ignition Module: 4.4 oz (125 g)
Total: Weight: 2.07 lb (943 g)
Technical Data:
Ignition Battery: 4.8-8.4 NiCd or NiMH, 6.6V LiFe or 2S LiPo pack
Gasoline/Oil Mix: 30:1
Replacement Spark Plug: NGK CM6 or equivalent
Idle Speed: 1800 rpm/min
Static Thrust:
15.9 lb (7.2 kg) @ 328 ft (100 m) altitude
15.0 lb (6.8 kg) @ 5,900 ft (1800 m) altitude
(1) 1pc RCGF-26cc BM Gas Engine
(2) 1pc RCGF Spark Plug (NGK CM6 size)
(3) 1pc Muffler with gasket and bolts (5X16mm)
(4) 4pcs mounting bolts 4 x 25 mm
(5) 4pcs mounting bolts 5 x 30 mm
(6) 1pc Electronic Ignition Module with additional tachometer lead
(7) 1pc adapter nut (use to mount the spinner)
(8) 1pc RCGF beam mount
(9) Long Throttle Arm Extension
(10) RCGF Decal
Safety Tips and Warnings
в—Џ This engine is not a toy. Please place your safety and the safety of others paramount
while operating. RCGF will not be responsible for any safety issues or accidents involving
this engine.
в—Џ Operate the engine in a properly ventilated area.
в—Џ Before starting the engine, please make sure all components including the propeller
and the engine mount are secure and tight. It is strongly recommended that a good
quality screw sealant is used during engine installation.
в—Џ During the break-in period, it is recommended that the engine be installed on the
aircraft or a test stand with an appropriate shock absorber. Otherwise it is probable that
vibration could rebound back to the engine and serious damages may occur during the
break-in period.
в—Џ For your safety and the safety of others, please do not stand in front or in line with the
propeller when the engine is running. Keep onlookers away from the running engine,
especially small children.
в—Џ Always use a balanced spinner and a balanced propeller. An unbalanced spinner and
propeller combination will cause high levels of vibration and may cause the propeller
shaft to break. Always use a lightweight spinner on your engine. Lightweight spinners are
considered to be those with a cone wall of 1mm or less. Heavy spinners could cause the
propeller shaft to break. Securely tighten the spinner and propeller on the engine to
prevent it from being thrown off the engine while running.
в—Џ Never use a propeller that has hit the ground. Even though it may look good from the
outside, it may be cracked on the inside which may cause it to disintegrate while in use.
Do not use a nicked, cracked or split propeller.
● Keep foreign objects away from the propeller. Make sure that nothing can be “sucked in”
by the propeller.
в—Џ Never start the engine on loose gravel or sand.
в—Џ Do not attempt to stop the engine by throwing anything into the path of the propeller.
● Make sure the fuel line is well-secured to the engine and to the fuel tank so that it won’t
come off in flight.
в—Џ Do not use silicone fuel line because it will be dissolved by the fuel. Use gasoline
approved vinyl or neoprene rubber fuel line. Always secure the fuel line away from the
cylinder. The engine’s heat can damage the fuel line.
в—Џ Never touch the engine immediately after a run. The engine will be hot.
в—Џ Before transporting your model, remove all the fuel from the fuel tank and fuel lines.
● Always use high-quality oil intended for 2-stroke (2-cycle) engines. It’s a good idea to
use a petroleum based 2-cycle motor oil like Lawn Boy All Season – Ashless, Generation
II oil for the breakin period. Break-in should be considered about the first 3-5 gallons you run the engine. A
high quality synthetic 2-cycle oil is recommended for optimum performance and a longer
engine life. Synthetic 2-cycle oils leave fewer combustion byproducts than natural oil
which can foul the engine and exhaust ports, resulting in reduced performance. Synthetic
oils also reduce friction and provide more fluidity at low temperatures.
в—Џ Do not install your throttle servo or kill switch servo inside the engine compartment.
Doing so could cause radio interference. Install all electronic radio devices as far away
from the engine as possible.
в—Џ The throttle and choke pushrods should be non-metallic.
в—Џ If the engine is not to be used for more than a month, drain the fuel tank and remove
any fuel from inside the carburetor. Do this by running the engine at idle until it quits by
running out of fuel.Keeping gasoline inside the carburetor over an extended period of
time will damage the diaphragm valve and clog passages inside the carburetor. Due to
the carburetor being more complicated than those used in glow engines, keep the fuel
clean by using a fuel filter. Use a filter intended to be used with gasoline engines. Metal
filters intended for glow engine are too coarse and will not screen out finer particles.
● Always filter your fuel by using an appropriate filter before putting it into the airplane’s
fuel tank.
в—Џ Gasoline is extremely flammable. Keep it away from an open flame, excessive heat or
sources of sparks.
в—Џ Do not smoke near the engine or the fuel tank.
в—Џ This engine was designed for use in a model aircraft. Do not attempt to use it for any
other purpose.
в—Џ Always install an ignition system kill switch on the aircraft used.
в—Џ Caution: Running the engine with a lean gas mixture will cause the engine to overheat
and burn the electrode of the spark plug. Pay close attention to the High-speed Needle
adjustment. Running the engine with the proper gas mixture will cause the spark plugs
to appear yellow at the ignition point.
в—Џ For optimum performance please use fresh or recently purchased 93 octane gasoline
(87 octane gasoline will suffice) with a 30:1 gas/oil mixture.
GAS/OIL Mixing Chart
1 Gallon Gasoline (128 fl oz/3.78L) / 2-Cycle Oil
(4.26fl oz/125.68ml) = 30:1 ratio
в—Џ Excessive running of the engine at idle speed can result in a seriously carbonized
spark plug.
в—Џ Keep the surface of the engine clean to ensure proper heat dissipation. Ensure proper
cooling/ventilation around the cylinder with adequate air exhaust.
в—Џ To avoid permanent damage to the electronic ignition system, never rotate the propeller
on your RCGF engine with the electronic ignition system switched on and the plug not
installed in the plug cap.
Installation Instructions
Prepare the engine for installation
Before beginning installation it’s a good idea to plan location of the various components
of the engine. Many of the following steps may need to be completed in a different order
than listed.
1. Check to see that all screws and bolts are tight. Check carefully for any cracks, broken,
or missing parts. Tighten or replace any damaged or missing parts before proceeding.
2. Install the silicone wire cover over the pick up lead coming from the engine (cut the
excess silicon wire cover) and connect the lead to the pick–up lead from the Electronic
Ignition Module. Secure the connection with the included three pin connector securing
3. Connect the kill switch lead to the red connector from the ignition control module using
the lead from the kill switch or with the included three pin connector with pig tail. Use one
of the included three pin securing clips to secure the connection.
4. Connect the ignition module battery to the kill switch. Any 4.8-6.0V, 1000mAh and
above capacity battery will work well for this.Use heat shrink tubing to secure this
5. Install the ignition kill switch and charge jack on the aircraft so that it is easily
accessible from the outside of the plane.
6. Install the ignition module securely in the airplane forward area. It is recommended
that a thin piece of foam rubber is placed between the module and the mounting surface
and that Velcro В® is used to hold the module in place.
7. Secure all connections with heat shrink tubing .
8. Install the silicone ignition wire cover over the ignition wire.
9. Install the spark plug into the engine head (6-9lbs torque).
Installing the RCGF 26cc BM on Your Airplane
Note: The RCGF 26CC BM must be installed on at least a 8mm firewall.
The firewall must be securely glued to the airplane. Use triangle stock and pin the firewall
with hardwood dowels to reinforce the firewall glue joints. Never install the RCGF 26cc
onto a firewall thinner than specified because it may fail due to the power of the engine.
Note: Please remember to remove the prop washer(M2624) and the small blind nut,
when you mount the adapter nut in your 26cc BM engine.
1. Select an engine mount. A two-piece engine mount that does not interconnect or
overlap at the firewall is preferred for the RCGF 26cc
2. Before securing the engine mount to the firewall, test fit the engine onto the mount and
place the mount onto the firewall. Press the blind nuts into the rear of the firewall. If you
choose to use regular nuts or lock nuts be sure to place washers on the bolts before
securing the nuts onto the bolts on the rear of the firewall. Be sure to use Threadlocker
on the screws holding the engine mount to the firewall.
3. Place the engine on the engine mount and at the recommended distance from the
firewall and test-fit the cowling on the aircraft to verify the distance. When you’re satisfied
with the engine’s position, mark the location of the four holes on the mount.
4. Remove the engine from the mount. Drill and tap the engine mount at the position of
the four mounting holes. Use an appropriate size screw. It’s a good idea to drill and tap
all the way through the mounting beams in order to secure each screw with a lock nut.
5. Secure the four screws with lock washers, flat washers, and lock nuts.
6. Install the fuel tank in the airframe. Use only gasoline-safe fuel lines and a gasoline
safe stopper. One line should go to the carburetor and the other is to be used as a vent
(a vent line is simply an open ended fuel line from the fuel tank which exits the engine
compartment or the fuselage; most vent lines exit at the bottom of the firewall).You can fill
the tank by using the carburetor line as fill line if you have access to it or install a third
line to be used as fill line. Installing a third line is the cleanest and easiest way to add fuel.
An alternative fueling set up is a 2-line system with a T-fitting approved for gasoline use.
Be sure to use a filler plug with either a 2 line or 3 line set-up. It is a good idea to add an
extension to the vent line as shown, that goes up and to the rear of the tank. This helps
to avoid draining fuel from the tank when the model is pointed down.
7. Install the throttle servo as far as possible from the engine. Make sure that you get the
carburetor’s full range of rotation with your servo travel. If needed, use the included Long
Throttle Arm Extension. Be sure to use a non-metallic linkage through an outer pushrod
tube and a screw lock connector so that the linkage is adjustable. Components for the
non-metallic linkage can be purchased at your local hobby shop.
8. Once the throttle servo is installed it’s a good idea to deactivate the throttle return
spring with a pair of needle nose pliers. Gently grab the spring and remove it from
tension on the throttle lever. Deactivating the spring will remove the load or stress on the
throttle servo.
9. Install the choke servo (optional) at the same distance as the throttle servo from the
engine. Be sure to use a non-metallic linkage and a Faslink to secure the throttle linkage
to the servo.
10. Connect the ignition wire from the ignition module to the spark plug.
11. Install the muffler onto the engine. Be sure to use threadlocker and that the ignition
wire does not contact the muffler.
12. Cut all necessary clearance, carburetor adjustment, cooling, and exhaust holes in the
cowl. A 1:3 ratio of airflow intake area to airflow exhaust area is recommended for proper
engine cooling.
13. Make sure the cowl is secured to the airplane and that the knurled thrust washer
protrudes from the cowl by at least 3.4mm [1/8”].
Install the Propeller
1. It is recommended that you test-run, tune, and break-in the engine before flying. To
make this easier we recommend that you remove the cowling.
2. Set the engine near the beginning of the compression stroke. Note the position of the
ignition magnet with the engine inverted.
3. Place the spinner back plate on the engine and the propeller on the crankshaft at the
one o’clock position.
4. Install the prop washer and 8x1.25mm adapter nut on the crankshaft.
5. Install the spinner cone. Be sure to use thread locker on the spinner bolt.
Adjustment of the Engine
Each RCGF Engine has been factory preset. However, differences in elevation will
influence the performance of the carburetor. To obtain optimum output of the engine,
slight adjustment of the carburetor may be necessary.
Engine Functions and Adjustments
1. Choke Control (the choke control should be used when the engine is cold)
2. Throttle
3. Idle Adjustment Screw (adjust the idle speed)
4. (L) Low-speed Needle (adjusts the fuel/air mixture at low speeds)
5. (H) High-speed Needle (adjusts the fuel/air mixture at high speeds)
Idle Adjustment
Turning the Idle Adjustment Screw clockwise will increase the idle speed. Turning the Idle
Screw counter-clockwise will decrease the idle speed.
Low Speed Needle Adjustment
Turning the Low-speed Needle clockwise will lean the fuel/air mixture at low speeds.
Turning the Low-speed Needle counter- clockwise will richen the fuel/air mixture at low
speeds. (The default or factory setting of the Low-speed Needle is as follows: turn the
needle to the fully stop/closed position and then turn back 1.5 turns.)
High Speed Needle Adjustment
Turning the High-speed Needle clockwise will lean the fuel/ air mixture at high speeds.
Turning the low-speed Needle counter-clockwise will richen the fuel/air mixture at high
speeds. (The default or factory setting of the High-speed Needle is as follows: turn the
needle to the fully stop/closed position and then open the needle 2 turns). It is
recommended that the High-speed needle be adjusted by the use of a tachometer to
obtain maximum speed. Smooth acceleration and deceleration is an indicator of proper
engine performance.
Ignition Timing Adjustment
The ignition timing is preset on the RCGF26cc at 28-30В° before Top Dead Center (TDC).
The ignition timing can be advanced or retarded by loosening the ignition sensor Phillips
head screws and sliding the sensor to the full extent clockwise (32В° advancing the
ignition) or counter clockwise (26В° retarding the ignition). Be sure to retighten the Phillips
head screws after adjusting the ignition timing. It is best to attach the sensor with the
screws centered in the slot as a starting point.
Advancing the timing causes combustion to occur earlier resulting in
higher performance of the engine. However, advancing the timing also
causes higher engine temperatures and can cause premature wear of
internal engine components.
Carburetor Adjustment Troubleshooting
If The engine hesitates when accelerated rapidly.or The rpm increases at idling. or The
engine stops when the throttle is moved from high to low.
The low-speed needle “L ” is too lean. Open it up about 1/8 of a
turn and try again.
If The idle is not steady.
The low-speed needle “L ” valve is too rich. Close it 1/8 of a turn
and try again.
If Engine stops at full throttle.
Or Engine hesitates when accelerated rapidly.
Or The engine will not come up to full rpm at full throttle.
The high-speed needle valve “H” is too lean. Open it up 1/8 of
a turn and try again.
If Your engine does not reach full rpm.
Or Carbon build-ups appear consistently on your spark plug.
The high-speed needle valve “H” is too rich. Close it up 1/8 turn
and try again.
Starting Procedures
When starting the engine the first time and during break-in it’s recommended that you run
the engine without the cowling. Also, for safety reasons do not adjust the carburetor while
the engine is running. There are two recommended ways to start the RCGF26cc:
A. Manual Starting
Note: When hand starting the RCGF 26cc, use a thick glove or heavy duty starter stick to
protect your hand.
1. The propeller should be installed on the drive washer at the one o’clock position and at
the beginning of the compression stroke so that it’s comfortable to flip it through
2. Have someone help you hold the airplane while you start the engine.
3. Switch the ignition to ON, close the choke on the carburetor and open the throttle
slightly from the idle position.
4. Flip the propeller counter clockwise several times briskly, until a popping sound is
heard. This indicates that the engine is firing.
5. Move the choke lever to the OPEN position.
6. Set the throttle to a high idle. Set the propeller so that it is at the beginning of the
compression stroke.
7. Flip the propeller through compression rapidly. If this is done properly, the engine will
start after several brisk flips of the propeller.
8. After starting, let the engine idle for 40 to 50 seconds. Open and close the throttle
slowly until the engine runs smoothly at idle and at full throttle. Acceleration should also
be smooth. If acceleration is not smooth, adjustments to the carburetor may be
necessary (see Adjustment of the Engine.)
9. If your engine does not start, repeat steps 2-8.
B. Electric Starter Starting
A 12V electric starter is recommended to start the RCGF 26cc
1. Make sure you use a good quality, lightweight aluminum spinner.
2. Have someone help you hold the airplane while you start it.
3. Switch the ignition to ON, close the choke plate on the carburetor and open the throttle
slightly from the idle position.
4. Use your electric starter to turn the engine over for several seconds, until a popping
sound is heard. This indicates that the engine is firing.
5. Move the choke lever to the open position.
6. Set the throttle to high idle and use your electric starter to turn over the engine until it
7. After starting, let the engine idle for 40 to 50 seconds. Open and close the throttle
slowly until the engine runs smoothly at idle and at full throttle. Acceleration should also
be smooth. If acceleration is not smooth, adjustments to the carburetor may be
necessary (see Adjustment of the Engine).
8. If your engine does not start, repeat steps 2-7.
Engine Troubleshooting
If your engine fails to start after the preceding starting procedures please check the
Ignition battery
voltage low
Engine does not fire
Battery wires faulty
or loose
Faulty spark plug
or not firing
Engine flooded
Engine starts,then rpm
Increases till engine cuts
Fuel not reaching
Charge or
replace battery
Replace wires or
Replace spark plug
or check for spark
Remove plug,
disconnect fuel
line, rotate prop
to remove fuel
Check for:
a) fuel in tank
b) fuel tubing
cut, blocked,
or kinked
c) carburetor
This can be done by removing the spark plug from the cylinder and attaching the plug on
the outside of the crankcase. Have an assistant turn the engine over while checking this
and be sure to have the spark plug firmly plugged into the ignition wire.
Warning: The high voltage from the ignition can cause bodily harm, especially when
checking for spark in this manner.
Optional Digital Tachometer (not included)
An optional Digital Tachometer is available that can be directly connected to the ignition
and display the RPM of the engine.The Futaba В® DSC Charge Adapter can be mounted
in the fuselage and allows easy external plug-in of the Digital Tachometer.
Many of the RCGF Ignition modules have an additional lead to plug into the Digital
Tachometer. If your ignition module does not have this additional lead, the Digital
Tachometer can still be used. Simply use the Y-harness (included with the Digital
Tachometer) to connect to the pick-up lead from the engine. Be sure to secure all
connections and to secure the Digital Tachometer or leads on the aircraft used.
Engine Maintenance
Please clean the fuel filter in the RCGF Carburetor periodically. Failure to do so may
result in miss-calibration of the needle adjustments. In order to do this it is necessary to
remove the Phillips head screw which secures the carburetor filter cover and the
carburetor filter gasket. Use only carburetor cleaner to clean the opening around the filter
If you need carburetor spare parts please contact our service center on local.
Warranty Information
The RCGF-26 has a two year limited warranty through RCGF service center
beginning at the date of purchase. Please retain your receipt as your proof of purchase.
Contact Us
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF