Toshiba 32L1400U1 Television User's Guide
Add to My manualsadvertisement
◉
Touch to zoom
Integrated High Definition LED Television User’s Guide: 32L1400U 40L1400U 50L1400U If you need assistance: Toshiba’s Support Web site support.toshiba.com For more information, see “Troubleshooting” on page 97 in this guide. Owner’s Record The model number and serial number are on the back and side of your TV. Print out this page and write these numbers in the spaces below. Refer to these numbers whenever you communicate with your Toshiba dealer about this TV. Model number: ___________________________________ Serial number: ___________________________________ Register your Toshiba television at register.toshiba.com Note: To display a High Definition picture, the TV must be receiving a High Definition signal (such as an over-the-air High Definition TV broadcast, a High Definition digital cable program, or a High Definition digital satellite program). For details, contact your TV antenna installer, cable provider, or satellite provider GMA300032013 3/14 2 Dear Customer, WARNING Thank you for purchasing this Toshiba LED TV. This document will help you use the many exciting features of your new LED TV. Before operating your LED TV, carefully read this document completely. Improper location and installation of a television can lead to the death of your child. Never place the television on furniture or in a location where children can climb up on and tip over the television. Please refer to the Child Safety information in item 26) on page 5 of the Important Safety Instructions/Installation section. Safety Precautions WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN. WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: If you decide to wall mount this television, always use a mounting bracket that has been Listed by an independent laboratory (such as UL, CSA, ETL) and is appropriate for the size and weight of this television. The use of inappropriate or non-Listed mounting brackets could result in serious bodily injury and/or property damage. See “To Display your LED TV on the included Pedestal Stand:” on page 6 NOTE TO CATV INSTALLERS This is a reminder to call the CATV system installer’s attention to Article 820-40 of the U.S. NEC, which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. For additional antenna grounding information, see 33) on page 5 and 34) on page 5 . CHILD SAFETY: PROPER TELEVISION PLACEMENT MATTERS TOSHIBA CARES • Manufacturers, retailers and the rest of the consumer electronics industry are committed to making home entertainment safe and enjoyable. • As you enjoy your television, please note that all televisions – new and old- must be supported on proper stands or installed according to the manufacturer’s recommendations. Televisions that are inappropriately situated on dressers, bookcases, shelves, desks, speakers, chests, carts, etc., may fall over, resulting in injury. TUNE IN TO SAFETY • ALWAYS follow the manufacturer’s recommendations for the safe installation of your television. • ALWAYS read and follow all instructions for proper use of your television. • NEVER allow children to climb on or play on the television or the furniture on which the television is placed. • NEVER place the television on furniture that can easily be used as steps, such as a chest of drawers. • ALWAYS install the television where it cannot be pushed, pulled over or knocked down. • ALWAYS route cords and cables connected to the television so that they cannot be tripped over, pulled or grabbed. WALL OR CEILING MOUNT YOUR TELEVISION • ALWAYS contact your retailer about professional installation if you have any doubts about your ability to safely mount your television. • ALWAYS use a mount that has been recommended by the television manufacturer and has a safety certification by an independent laboratory (such as UL, CSA, ETL). • ALWAYS follow all instructions supplied by the television and mount manufacturers. • ALWAYS make sure that the wall or ceiling where you are mounting the television is appropriate. Some mounts are not designed to be mounted to walls and ceilings with steel studs or cinder block construction. If you are unsure, contact a professional installer. • Televisions can be heavy. A minimum of two people is required for a wall or ceiling mount installation. MOVING AN OLDER TELEVISION TO A NEW PLACE IN YOUR HOME • Many new television buyers move their older CRT televisions into a secondary room after the purchase of a flat-panel television. Special care should be made in the placement of older CRT televisions. • ALWAYS place your older CRT television on furniture that is sturdy and appropriate for its size and weight. • NEVER place your older CRT television on a dresser where children may be tempted to use the drawers to climb. • ALWAYS make sure your older CRT television does not hang over the edge of your furniture. CE.org/safety 4 Important Safety Instructions 1) 2) 3) 4) Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug Wide blade has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10) Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. • ALWAYS contact a service technician to inspect the TV any time it has been damaged or dropped. 15) CAUTION: • To reduce the risk of electric shock, do not use the polarized plug with an extension cord, receptacle, or other outlet unless the blades can be inserted completely to prevent blade exposure. • To prevent electric shock, match wide blade of plug to wide slot; fully insert. 16) CAUTION: • Do not let children swallow any small parts included on or with the product or play with the plastic bag. Keep the small parts and the plastic bag out of the reach of children. 17)CAUTION: • Do not let water or other liquids come into contact with the product, as it may result in damage. 18) WARNING: • To prevent the spread of fire, keep candles or other open flames away from this product at all times. • Keep the product away from direct sunlight, fire or a heat source such as a heater. This may reduce the product life time or result in fire. Installation, Care, and Service Installation 11) Only use attachments/accessories specified by the manufacturer. Follow these recommendations and precautions and heed all warnings when installing your TV: 12)Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over. 19) 13)Unplug this apparatus during lightning storms or when unused for long periods of time. 21)NEVER route the product’s power cord inside a wall or similar enclosed area. 14)Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as when power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 22)Never modify this equipment. Changes or modifications may void: a) the warranty, and b) the user’s authority to operate this equipment under the rules of the Federal Communications Commission. Additional Safety Precautions 14a) CAUTION: If the TV is dropped and the cabinet or enclosure surface has been damaged or the TV does not operate normally, take the following precautions: • ALWAYS turn off the TV and unplug the power cord to avoid possible electric shock or fire. • NEVER allow your body to come in contact with any broken glass or liquid from the damaged television. The LCD panel inside the TV contains glass and a toxic liquid. If the liquid comes in contact with your mouth or eyes, or your skin is cut by broken glass, rinse the affected area thoroughly with water and contact your doctor immediately. WARNING: Never expose the batteries to excessive heat such as sunshine, fire, or the like. 20)ALWAYS plug the product into an outlet that is located in such a manner that it can be easily unplugged in case the product requires service. 23) DANGER: RISK OF SERIOUS PERSONAL INJURY, DEATH, OR EQUIPMENT DAMAGE! Never place the TV on an unstable cart, stand, or table. The TV may fall, causing serious personal injury, death, or serious damage to the TV. 5 24)When selecting a location for the TV, • NEVER allow any part of the TV to hang over the edge of the supporting furniture, • NEVER place the TV on tall furniture (for example, entertainment centers or bookcases) without anchoring both the furniture and the TV to a suitable support, • Never place cloth or other material between the TV and the supporting furniture. • NEVER allow children to climb on the TV 25)To avoid damage to this product, never place or store the TV in direct sunlight; hot, humid areas; or areas subject to excessive dust or vibration. 26)Always place the TV on the floor or a sturdy, level, stable surface that can support the weight of the unit. Secure the TV using one of the following methods: (1) Secure the TV with a mounting screw (Recommended). • Place the TV on a sturdy surface that has a sufficient thickness and screw the unit on the surface securely by using the mounting screw and the fall-prevention screw hole. • If secured to furniture or other movable objects, the furniture must be secured to an immovable structure using the method shown in item 2 below. 30)Never allow anything to rest on or roll over the power cord, and never place the TV where the power cord is subject to wear or abuse. 31)Never overload wall outlets and extension cords. 32)Always operate this equipment from a 120V AC, 60 Hz power source. 33)Always make sure the antenna system is properly grounded to provide adequate protection against voltage surges and built-up static charges (see Section 810 of the National Electric Code). Mounting screw TV Back Screw hole (2) Secure the TV with a sturdy strap to a wall stud, pillar, or other immovable structure. When connecting the strap: - attach the strap to the TV using the hooks on the back of the TV, the clips on the pedestal, or the hole in the base of the pedestal as available. - make sure the strap is tight, secure, and parallel to the floor. Sturdy strap (as short as possible) 4" min. TV side 29)Always leave a space of at least 4 (four) inches around the TV. The slots and openings are provided to protect the TV from overheating and to help maintain reliable operation of the TV. Hook TV top 27)The product shall not be exposed to dripping or splashing, and that no objects filled with liquids, such as vases, shall be placed on the apparatus. 28)Never block or cover the slots or openings in the TV cabinet back, bottom, and sides. Never place the TV: • on a bed, sofa, rug, or similar surface; • too close to drapes, curtains, or walls; or • in a confined space such as a bookcase, built-in cabinet, or any other place with poor ventilation. 34) DANGER: RISK OF SERIOUS PERSONAL INJURY OR DEATH! • When installing a rooftop antenna, use extreme care to make sure you are never in a position where your body (or any item you are in contact with, such as a ladder or screwdriver) can accidentally touch overhead power lines. Never locate the antenna near overhead power lines or other electrical circuits. • Never attempt to install any of the following during lightning activity: a) an antenna system; or b) cables, wires, or any home theater component connected to an antenna or phone system. Care For better performance and safer operation of your TOSHIBA TV, follow these recommendations and precautions: 35)If you use the TV in a room where the temperature is 32° F (0° C) or below, the picture brightness may vary until the LED warms up. This is not a sign of malfunction. 36) WARNING: RISK OF SERIOUS PERSONAL INJURY OR EQUIPMENT DAMAGE! • Never use chemicals (such as air fresheners, cleaning agents, etc.) on or near the TV pedestal. 6 Studies indicate that plastics may weaken and crack over time from the combined effects of chemical agents and mechanical stress (such as the weight of the TV). Failure to follow these instructions could result in serious injury and/or permanent damage to TV and TV pedestal. • Always unplug the TV before cleaning. Gently wipe the display panel surface (the TV screen) using a dry, soft cloth (cotton, flannel, etc.). A hard cloth may damage the surface of the panel. Avoid contact with alcohol, thinner, benzene, acidic or alkaline solvent cleaners, abrasive cleaners, or chemical cloths, which may damage the surface. Never spray volatile compounds such as insecticide on the cabinet. Such products may damage or discolor the cabinet. 37)Never hit, press, or place anything on the back cover. These actions will damage internal parts. 38) WARNING: RISK OF ELECTRIC SHOCK! Never spill liquids or push objects of any kind into the TV cabinet slots. 39)During a lightning storm, do not touch the connecting cables or product. 40)For added protection of your TV from lightning and power surges, always unplug the power cord and disconnect the antenna from the TV if you leave the TV unattended or unused for long periods of time. 41)Always unplug the TV to completely disconnect from mains power. When the TV is turned off using the on/ off switch, it is not completely disconnected from power and a minute amount of current is still consumed. 42)During normal use, the TV may make occasional snapping or popping sounds. This is normal, especially when the unit is being turned on or off. If these sounds become frequent or continuous, unplug the power cord and contact a Toshiba Authorized Service Provider. 43) WARNING: RISK OF SERIOUS PERSONAL INJURY OR EQUIPMENT DAMAGE! Never strike the screen with a sharp or heavy object. 44) • The LCD screen of this product can be damaged by ultraviolet radiation from the sun. When selecting a location for the television, avoid locations where the screen may be exposed to direct sunlight, such as in front of a window. • Never touch, press, or place anything on the LCD screen. These actions will damage the LCD screen. If you need to clean the LCD screen, follow the instructions in item 36) on page 5 . Service 45) WARNING: RISK OF ELECTRIC SHOCK! Never attempt to service the TV yourself. Opening and removing the covers may expose you to dangerous voltage or other hazards. Failure to follow this WARNING may result in death or serious injury. Refer all servicing not specified in this manual to a Toshiba Authorized Service Provider. 46)If you have the TV serviced: • Ask the service technician to use only replacement parts specified by the manufacturer. • Upon completion of service, ask the service technician to perform routine safety checks to determine that the TV is in safe operating condition. Choosing a location for your LED TV To Display your LED TV on the included Pedestal Stand: Observe the following safety precautions: 1) Read and follow the pedestal assembly instructions included with the pedestal. CAUTION: Before beginning pedestal assembly, carefully lay the front of the LCD Panel face down on a flat, cushioned surface such as a quilt or blanket. Leave the bottom of the unit protruding over the edge of the surface and assemble the pedestal as described in this instruction document. Note: Extreme care should always be used when attaching the pedestal stand to avoid damage to the LCD panel. 2) Place the TV on a sturdy, level surface that can support the weight of the TV. 3) Be sure to secure the TV to a wall, pillar, surface, or other immovable structure see item 26) on page 5 for additional details. To Display your LED TV using a Wall Bracket: If you decide to wall mount your LED TV, always use a wall bracket Listed by an independent laboratory (such as UL, CSA, ETL) that is appropriate for the size and weight of the TV: 1) CAUTION: Two people are required for installation. 2) Unplug and remove any cables and/or other component connectors from the rear of the TV. 3) Remove the screws of the VESA Mounting Pattern shown in the table below, if applicable. CAUTION: Do not use the screws removed from the back cover to attach the wall mount bracket to the TV. 4) Always use the screws supplied or recommended by the wall mount manufacturer. 5) Follow the instructions provided with your wall bracket. Before proceeding, make sure the appropriate bracket(s) are attached to the wall and the back of the TV as described in the instructions provided with the wall bracket. 6) After attaching the appropriate bracket(s) to the wall and the back of the TV, remove the pedestal stand from the TV, as described in this instruction document. 7 7) VESA Mounting Pattern TV Size 50” TV. Hole Pattern (HxV) 32” 200mm x 200mm M6 40” 200mm x 200mm M6 50” 400mm x 200mm M8 Removing the Pedestal Stand 1) Carefully lay the front of the unit face down on a flat, cushioned surface such as a quilt or blanket. Leave the stand protruding over the edge of the surface. Note: Extreme care should always be used when removing the pedestal stand to avoid damage to the LCD panel. 2) Remove the stand screws shown in the diagram below. This will allow removal of the pedestal stand. 3) Once you have removed the screws holding the pedestal stand in place, remove the pedestal stand from the TV. 32” TV. VESA Mounting Pattern Two stand screws Hook Sturdy strap (as short as possible) (Sample Illustration) 40” TV. VESA Mounting Pattern Two stand screws VESA Mounting Pattern Screw Size Hook Sturdy strap (as short as possible) (Sample Illustration) Two stand screws Hook Sturdy strap (as short as possible) (Sample Illustration) CAUTION: Always place the TV on the floor or a sturdy, level, stable surface that can support the weight of the unit. To secure the TV, use a sturdy strap from the hook(s) on the rear of the TV to a wall stud, pillar, or other immovable structure. Make sure the strap is tight, secure, and parallel to the floor. 8 FCC Declaration of Conformity Compliance Statement (Part 15): Toshiba 32L1400U, 40L1400U, 50L1400U Television models comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. The party responsible for compliance to these rules is: Toshiba America Information Systems, Inc. 9740 Irvine Blvd., Irvine, CA 92618. Ph: 800-631-3811 Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by removing and applying power to the equipment, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications to this equipment not expressly approved by Toshiba could void the user’s authority to operate this equipment. ENERGY STAR® User Information ENERGY STAR User Information Statement: the factory default settings of this television meet ENERGY STAR® requirements. Changing Picture Settings may increase energy consumption, possibly beyond the limits required for ENERGY STAR qualification. To ensure your television is operating at optimal energy efficiency, select [Home] mode during initial activation. To return to [Home] mode settings, select the [Installation] icon from the menu, select [Store / Home Mode], then select [Home]. This places the TV in [Standard] mode. [Standard] mode is recommended for normal home use. ENERGY STAR® qualified TV. Products that earn the ENERGY STAR prevent green house gas emissions by meeting strict guidelines set by the U.S. Environmental Protection Agency. ENERGY STAR and the ENERGY STAR mark are registered U.S. marks. Important notes about your TV The following symptoms are technical limitations of LCD Display technology and are not an indication of malfunction; therefore, Toshiba is not responsible for perceived issues resulting from these symptoms. 1) An afterimage (ghost) may appear on the screen if a fixed, non-moving image appears for a long period of time. The afterimage is not permanent and will disappear in a short period of time. 2) The LCD panel contained in this TV is manufactured using an extremely high level of precision technology; however, there may be an occasional pixel (dot of light) that does not operate properly (does not light, remains constantly lit, etc.). This is a structural property of LCD technology, is not a sign of malfunction, and is not covered under your warranty. Such pixels are not visible when the picture is viewed from a normal viewing distance. Note: Interactive video games that involve shooting a “gun” type of joystick at an on-screen target may not work with this TV. 9 Trademark Information • • ColorStream, ColorMaster, DynaLight, GameTimer, Native Mode, Stable Sound, Surflock , TheaterWide, and TosLink are trademarks or registered trademarks of Toshiba America Information Systems, Inc, and/or Toshiba Corporation. Blu-ray Disc™, Blu-ray™, and the logos are trademarks of the Blu-ray Disc Association. •For DTS patents, see http://patents.dts. com. Manufactured under license from DTS Licensing Limited. DTS, the Symbol, & DTS and the Symbol together are registered trademarks, and DTS TruSurround is a trademark of DTS, Inc. © DTS, Inc. All Rights Reserved. •Manufactured under license from Dolby® Laboratories. Dolby® and the double-D symbol are trademarks of Dolby® Laboratories. •The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. •MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and Thomson. •This production contains Bitstream Vera Sans fonts under the following copyright: Copyright © 2003 by Bitstream, Inc. All Rights Reserved. Bitstream Vera is a trademark of Bitstream, Inc. •All other brand and product names are trademarks or registered trademarks of their respective companies. Copyright © 2014 by Toshiba America Information Systems, Inc. All rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed, however, with respect to the use of the information contained herein. Notice The information contained in this manual, including but not limited to any product specifications, is subject to change without notice. TOSHIBA AMERICA INFORMATION SYSTEMS, INC., TOSHIBA OF CANADA LIMITED, AND TOSHIBA DE MEXICO, S.A. DE. C.V.. (COLLECTIVELY TOSHIBA) PROVIDES NO WARRANTY WITH REGARD TO THIS MANUAL OR ANY OTHER INFORMATION CONTAINED HEREIN AND HEREBY EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE WITH REGARD TO ANY OF THE FOREGOING. TOSHIBA ASSUMES NO LIABILITY FOR ANY DAMAGES INCURRED DIRECTLY OR INDIRECTLY FROM ANY TECHNICAL OR TYPOGRAPHICAL ERRORS OR OMISSIONS CONTAINED HEREIN OR FOR DISCREPANCIES BETWEEN THE PRODUCT AND THE MANUAL. IN NO EVENT SHALL TOSHIBA BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL, OR EXEMPLARY DAMAGES, WHETHER BASED ON TORT, CONTRACT OR OTHERWISE, ARISING OUT OF OR IN CONNECTION WITH THIS MANUAL OR ANY OTHER INFORMATION CONTAINED HEREIN OR THE USE THEREOF. Contents Chapter 1: Introduction.............................................................. 16 Features...................................................................17 Overview of installation, setup, and use....................18 TV front and side panel controls and connections.....19 TV back panel connections.......................................20 Chapter 2: Connecting Your TV.................................................. 22 Overview of cable types............................................22 Coaxial (F-type) cable ........................................22 Standard A/V cables (red/white/yellow)..............23 Component video cables (red/green/blue)..........23 HDMI® cable (with HDMI Logo)..........................23 Optical audio cable.............................................24 About the connection illustrations......................24 Connecting a VCR, antenna, cable TV, or camcorder.....................................................24 Connecting a Blu-rayTM / DVD player, satellite receiver with ColorStreamTM or VCR ..................26 10 Contents 11 Connecting an HDMI® or DVI device to the HDMI® input.......................................................27 HDMI® CEC connection............................................29 Connecting a digital audio system............................31 Connecting a computer............................................32 Connection to the TV’s HDMI® terminal..............32 Chapter 3: Using the Remote Control........................................ 33 Installing batteries....................................................33 Remote control effective range.................................34 Learning about the remote control............................36 Chapter 4: Menu Layout and Navigation................................... 39 Main menu layout.....................................................39 Navigating the menu system....................................41 Chapter 5: Setting up your TV.................................................... 42 Initial Setup..............................................................42 Installation setup selection.......................................43 Storing channels in memory (optional)....................44 Auto Tuning..............................................................44 Manual Tuning..........................................................46 Setting channel skip.................................................46 Setting the AV input mode........................................47 Setting the time zone................................................47 Viewing the system status........................................48 Resetting Factory Defaults..................................48 Chapter 6: Setting up your TV.................................................... 49 Selecting the video input source...............................49 Labeling the video input sources..............................51 Tuning channels using the Channel Browser.............52 Favorites browser.....................................................53 Elements of the Channel Browser.......................54 Adding and clearing channels and inputs in the History List.........................................56 12 Contents Tuning to the next programmed channel.............56 Tuning to a specific channel (programmed or unprogrammed)...........................................56 Switching between two channels using Channel Return............................................57 Switching between two channels using SurfLock™...................................................57 Selecting the picture size..........................................58 Full.....................................................................59 TheaterWide 1....................................................59 TheaterWide 2....................................................59 TheaterWide 3....................................................60 Native.................................................................60 4:3.....................................................................61 Normal...............................................................61 Dot by Dot..........................................................61 Scrolling the TheaterWideTM picture (TheaterWide 2 and 3 only)................................62 Using the Auto Aspect feature..................................62 Using the 4:3 Stretch................................................63 Using the FREEZE feature.........................................63 Adjusting the picture ...............................................64 Selecting the picture mode.................................64 Adjusting the picture quality...............................65 Using closed captions..............................................66 Base closed captions..........................................66 Digital CC settings..............................................67 Adjusting the audio..................................................68 Muting the sound...............................................68 Using the Digital Audio Selection........................69 Selecting stereo/SAP broadcasts........................69 Adjusting the audio quality.................................70 DTS TruSurround™............................................71 Sound Mode.......................................................71 Stable SoundTM. .................................................71 Contents 13 Using the Dolby® Digital Dynamic Range Control feature ............................................71 Selecting the PIN code.............................................72 Enter a new PIN code..........................................72 Forgotten PIN code............................................72 Changing or deleting your PIN code...................72 Using parental controls (for USA region)..................72 Blocking TV programs and movies by rating (V-Chip).......................................................72 Downloading an additional rating system...........73 Displaying ratings..............................................76 Unlocking programs temporarily........................76 Using the input lock feature......................................77 Locking channels.....................................................77 Using the GameTimerTM. ....................................78 Using the panel lock feature................................79 Using the Media Player.............................................80 Auto Start function.............................................81 To open the Media Player....................................81 Viewing photo files.............................................82 Playing music files.............................................84 Viewing photo files and playing music files at the same time ..........................................85 Sorting photo or music files...............................85 Setting the sleep timer..............................................86 No Signal Power Down.............................................87 Using HDMI® CEC....................................................87 HDMI® CEC playback device (Blu-rayTM/DVD player, etc.) control . ....................................87 Other HDMI® CEC functions...............................89 Setting up HDMI® CEC........................................90 Using the HDMI® settings feature.............................90 HDMI® 1(or 2) RGB Range.................................90 HDMI® Information Display................................91 Displaying TV status information..............................91 Understanding the last mode memory feature..........92 14 Contents Chapter 7: Using the TV’s Advanced Features.......................... 93 Using the advanced picture settings.........................93 ColorMaster™....................................................93 Base Color Adjustment.......................................93 Color Temperature..............................................94 Static Gamma.....................................................94 DynaLightTM.......................................................95 Dynamic Contrast...............................................95 Cinema Mode.....................................................95 Noise Reduction.................................................95 Chapter 8: Troubleshooting........................................................ 97 General troubleshooting...........................................97 Picture problems......................................................98 Sound problems.......................................................99 Remote control problems.......................................100 Channel tuning problems.......................................100 Closed caption problems........................................101 Rating blocking (V-Chip) problems........................101 No HDMI® CEC operation.......................................101 HDMI® problems....................................................102 Media Player problems...........................................102 If the problem persists after trying the solutions.....102 Appendix A: Specifications...................................................... 103 Television system...................................................103 Channel coverage...................................................103 Power source.........................................................104 Power maximum current..................................104 Power consumption.........................................104 Audio power.....................................................104 Speaker type..........................................................104 Video/audio terminals............................................104 Video/audio input.............................................104 ColorStreamTM (component video) HD input.....105 Contents 15 HDMI®input......................................................105 Dimensions (with stand)........................................105 Weight / mass (with stand)...............................105 Operating conditions........................................105 Supplied accessories.............................................106 Acceptable signal formats for HDMI®.....................106 HDMI® signal formats.......................................106 Appendix B: Index..................................................................... 107 Chapter 1 Introduction Safety icons This manual contains safety instructions that must be observed to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data. These safety cautions have been classified according to the seriousness of the risk, and icons highlight these instructions as follows: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. Indicates a potentially hazardous situation which, if not avoided, may result in property damage. Provides important information. 16 Introduction Features 17 Features The following are just a few of the many exciting features of your new Toshiba wide screen, integrated HD LED TV: v Integrated digital tuning (8VSB ATSC and QAM) — Eliminates the need for a separate digital converter set-top box (in most cases) v 1366 x 768 output resolution (32L1400U) 1920 x 1080 output resolution (40/50L1400U) v Two HDMI®—Digital, High-Definition Multimedia Interfaces with 1080p input support. See “Connecting an HDMI® or DVI device to the HDMI® input” on page 27 v ColorStreamTM HD—High-resolution component video input and shared composite video input, see “Connecting a Blu-ray Blu- TM TM / DVD satellite player, satellite with ColorStreamTM /rayTM DVD player, receiverreceiver with ColorStream or VCR” or VCR” on page 26 v Digital Audio Out—Optical audio connection with Dolby® Digital optical output form. See “Connecting a digital audio system” on page 31 v DTS TruSurround™—Delivers an immersive virtual surround sound experience over front facing speaker configurations, complete with rich bass, high frequency detail and clear dialog. For more information, see “DTS TruSurround™” on page 71 v ColorMasterTM—Allows you to adjust the TV’s standard colors, see “ColorMaster™” on page 93 v Cinema Mode—Shows film-like quality movies, see “Cinema Mode” on page 95 v DynaLightTM—Backlight control monitors the brightness of each video frame and automatically adjusts backlight intensity based on the content to create higher dynamic contrast, for TM ” onon deeper blacks and increased depth, see “DynaLight “DynaLightTM” page 95 v DNR—Digital picture Noise Reduction, see “DNR” on page 96 v Edge Enhancer—Lets you adjust the levels for your desired picture settings and achieve a sharper picture, see“Edge Enhancer” on page 96 v HDMI® CEC—Allows control of external devices from the TV remote via HDMI® connection, see “Using HDMI® CEC” on page 87 v Media Player—Allows you to view photo files and play music files, see “Using the Media Player” on page 80 v ENERGY STAR® qualified 18 Introduction Overview of installation, setup, and use Overview of installation, setup, and use Follow these steps to set up your TV and begin using its many exciting features. 1 Carefully read the important safety, installation, care, and service information. Keep this document for future reference. 2 To choose a location for the TV: v Read “Important notes about your TV” on page 8 3 4 5 6 7 8 9 10 11 12 13 v Place the TV on the floor or a sturdy, level, stable surface that can support the weight of the unit. Secure the TV to a wall, pillar, or other immovable structure, see 26) on page 5. v Place the TV in a location where light does not reflect on the screen. v Always leave a space of at least 4 (four) inches around the TV. The slots and openings are provided to protect the TV from overheating and to help maintain reliable operation of the TV. Do not plug in any power cords until after you have connected all cables and devices to your TV. Before connecting cables or devices to the TV, learn the functions of the TV’s connections and controls, see “Overview of cable types” on page 22 Connect your other electronic device(s) to the TV, see “Connecting Your TV” on page 22 Install the batteries in the remote control, see “Installing batteries” on page 33 See “Using the Remote Control” on page 33 for an overview of the buttons on the remote control. After connecting all cables and devices, plug in the power cords for your TV and other devices. Then press the POWER button on the TV control panel or remote control to turn on the TV. See “Navigating the menu system” on page 41 for a quick overview of navigating the TV’s menu system. Program channels into the TV’s channel memory, see “Auto Tuning” on page 44 For details on using the TV’s features, see Chapter 6 and Chapter 7 For help, refer to “Troubleshooting” on page 97 For technical specifications, see “Specifications” on page 103 Introduction TV front and side panel controls and connections 19 If the TV stops responding to the buttons on the remote control or TV control panel and you cannot turn the TV off or on, unplug the power cords for a few seconds and then plug them in and try again. TV front and side panel controls and connections Left side panel TV front TV top 3 4 5 6 2 1 (Sample Illustration) 32L1400U - Front and side panel controls and connections Left side panel TV front TV top 3 4 5 6 2 1 (Sample Illustration) 40/50L1400U - Front and side panel controls and connection 1 2 3 4 Power On/Standby LED—Power indicator light, (glows red when the TV power is Off). Remote sensor (embedded)—Point the remote control toward this remote sensor. POWER—Turns the TV On/Off. ▲/▼/+/ ─ — Adjust the volume level, change the channel, or change the input or source you are viewing, depending on the mode, which is selected by the CH/INPUT button. 20 Introduction TV back panel connections 5 6 CH/INPUT—Switches the function of the ▲/▼/+/─ buttons to select the volume, channel, or input mode. • In Volume mode, the buttons increase or decrease the volume. • In Channel mode, the buttons change the channel up or down. • In Source mode, the buttons toggle the input from one source to the next. USB port—Accesses JPEG or MP3 files, or updates TV firmware. TV back panel connections For explanations of cable types and connections, see on page 22. 1 2 3 5 Power Cord 4 (Sample Illustration) 32L1400U - Back panel connections 1 5 2 3 Power Cord 4 5 Power Cord (Sample Illustration) 40/50L1400U - Back panel connections 1 ANT/CABLE—Antenna input that supports analog (NTSC) and digital (ATSC) off-air antenna signals and analog and digital cable TV (QAM) signals. Introduction TV back panel connections 2 3 4 5 21 ColorStreamTM HD—High-resolution component video input and shared composite video input, see “Connecting a Blu-ray Blu- TM TM or VCR” or / DVD player, receiverreceiver with ColorStream rayTM / DVD satellite player, satellite with ColorStreamTM VCR” on page 26 HDMI® IN—High-Definition Multimedia Interface input receives digital audio and uncompressed digital video from an HDMI® device or uncompressed digital video from a DVI device. HDMI® connection is necessary to receive 1080p signals. Digital Audio out— Optical audio output of Dolby® Digital or PCM (pulse-code modulation) format for connecting an external Dolby® Digital decoder, amplifier, or home theater system with optical audio input. Power Cord— Plug one end of the power cord into the jack on the back of the unit, and the other end into a live electrical outlet.(Only for 40/50L1400U models) The included power cord is for use with this unit only. Do not use it with other equipment. If you are not going to use the unit for an extended period of time, disconnect the power cord from the wall outlet. Whenever the power cord is plugged into the wall outlet, it will draw some power, even when the unit is off. If the TV stops responding to the buttons on the remote control or TV control panel and you cannot turn the TV off or on, unplug the power cords for a few seconds and then plug them in and try again.. Chapter 2 Connecting Your TV Overview of cable types Before purchasing cables, know the connector types your devices require. You can purchase cables from most stores that sell audio/ video devices. Coaxial (F-type) cable (Sample Illustration) Coaxial cable Coaxial (F-type) cable connects your antenna, cable TV service, and/or cable converter box to the ANT/CABLE input on your TV. Please tighten this connection by hand. Using tools may damage the connection. 22 23 Connecting Your TV Overview of cable types Standard A/V cables (red/white/yellow) (Sample Illustration) Standard AV cables Standard A/V cables (composite video) usually come in sets of three, and connect to video devices with analog audio and composite video output. These cables (and the related inputs on your TV) are typically color-coded according to use: yellow for video, red for stereo right audio, and white for stereo left (or mono) audio. Component video cables (red/green/blue) Component video cables (red/green/blue) Component video cables come in sets of three and connect with video devices with component video output. (ColorStreamTM is Toshiba’s brand of component video.) These cables are typically color-coded red, green, and blue. Separate audio cables are required for a complete connection. Component video cables provide better picture quality than composite video cables. HDMI® cable (with HDMI Logo) (Sample Illustration) HDMI® cable HDMI® (High-Definition Multimedia Interface) cable connects to devices that have an HDMI® output. An HDMI® cable delivers digital audio and video in its native format. Separate audio cables are not required, see “Connecting an HDMI® or DVI device to the HDMI® input” on page 27 24 Connecting Your TV Connecting a VCR, antenna, cable TV, or camcorder HDMI® cables provide the best audio and picture quality. Optical audio cable (Sample Illustration) Optical audio cable Optical audio cable connect receivers with Dolby® Digital or PCM (pulse-code modulation) optical audio input to the TV’s Digital Audio Out terminal, see “Connecting a digital audio system” on page 31. About the connection illustrations You can connect different types and brands of devices to your TV in several different configurations. The connection illustrations in this manual are representative of typical device connections only. The input/output terminals on your devices may differ from those illustrated herein. For details on connecting and using your specific devices, refer to each device’s User’s Guide. Connecting a VCR, antenna, cable TV, or camcorder From cable TV From cable TV Cable box or antenna Camcorder AUDIO OUT VIDEO L IN CH 3 CH 4 TV back panel R OUT Stereo VCR VIDEO L AUDIO R IN OUT L R CH 3 CH 4 IN from ANT OUT to TV (Sample Illustration) 32/40/50L1400U—Connecting to a VCR, antenna, or cable TV, or camcorder Items needed: v Coaxial cables v Standard AV cables If you have a mono VCR, connect L/MONO on the TV to your VCR’s audio out terminal using the white audio cable only. v Standard audio cable TV back panel 25 Connecting Your TV Connecting a VCR, antenna, cable TV, or camcorder The menu setting may need to be changed in order to watch the shared input between composite and component video. Composite and component video cannot be used simultaneously. When you use a cable box, you may not be able to use the remote control to program or access certain features on the TV. When you use ColorStreamTM HD or Video, switch AV input mode appropriately. To view the antenna or cable signal: Select ANT/CABLE video input source on the TV.* To view basic and premium cable channels: Turn off the VCR. Select the ANT/CABLE video input source on the TV.* Tune the TV to channel 3 or 4 (whichever channel the cable box output is set to). Use the cable box controls to change channels. To view the VCR or camcorder video: Turn on the VCR or camcorder video. Select VIDEO input source on the TV.* *To select the video input source, press the INPUT button on the remote control, see “Selecting the video input source” on page 49 The unauthorized recording, use, distribution, or revision of television programs, videotapes, DVDs, and other materials is prohibited under the Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability. 26 Connecting Your TV TM Connectinga aBlu-rayTM Blu-rayTM/ DVD / DVD player, satellite receiver with ColorStream Connecting player, satellite receiver with ColorStreamTM or VCRor VCR Connecting a Blu-rayTM / DVD player, satellite receiver with ColorStreamTM or VCR TV back panel From antenna Stereo VCR VIDEO L AUDIO R IN OUT L CH 3 CH 4 IN from ANT OUT to TV R From satellite dish Y Satellite IN PB AUDIO OUT L PR COMPONENT VIDEO S-VIDEO VIDEO OUT OUT R Satellite receiver, Blu-ray or DVD player TM (Sample Illustration) 32/40/50L1400U—Connecting a Blu-ray™ / DVD player or Satellite receiver with ColorStreamTM (or VCR). ColorStreamTM and composite video cables cannot be connected simultaneously. Items needed: v Coaxial cables v Standard AV cables If you have a mono VCR, connect L/MONO on the TV to your VCR’s audio out terminal using the white audio cable only. v Standard audio cables v Component video cables v You can connect the component video cables (plus audio cables) from the DVD player or satellite receiver to the COLOR STREAM HD terminal in the TV. The COLOR STREAM HD terminal can be used to display Progressive (480p, 720p) and Interlaced (480i, 1080i) scan systems. Please note that 1080p is not supported. Check the User’s Guide of the DVD player in order to determine the best output signal available. v If your DVD player or satellite receiver does not have component video, connect a standard A/V cable to the AUDIO/VIDEO terminal. If your DVD player has HDMI® video, see “Connecting an HDMI® or DVI device to the HDMI® input” on page 27 27 Connecting Your TV Connecting an HDMI® or DVI device to the HDMI® input When you use ColorStreamTM HD or Video, switch AV input mode appropriately. To view antenna or Cable channels: Select the ANT/CABLE video input source on the TV.* To view the DVD player: Turn on the DVD player. Select the COLORSTREAM HD video input source on the TV.* To view satellite programs using the component video connections: Turn on the satellite receiver. Select the COLORSTREAM HD video input source on the TV.* To view the VCR or view and record antenna channels: Turn on the VCR. Tune the VCR to the channel you want to watch. Select the VIDEO video input source on the TV.* To record a TV program while watching a DVD: Turn on the VCR. Tune the VCR to the channel to record. Select the COLORSTREAM HD video input source on the TV* to view the DVD. *To select the video input source, press the INPUT button on the remote control, see “Selecting the video input source” on page 49 The unauthorized recording, use, distribution, or revision of television programs, videotapes, DVDs, and other materials is prohibited under the Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability. Connecting an HDMI® or DVI device to the HDMI® input The HDMI® input on your TV receives digital audio and uncompressed digital video from an HDMI® source device, or uncompressed digital video from a DVI (Digital Visual Interface) source device. This input is designed to accept HDCP (High- Bandwidth DigitalContent Protection) program material in digital form from EIA/ CEA-861-D– compliant[1] consumer electronic devices (such as a set-top box or DVD player with HDMI® or DVI output). The HDMI® input can accept and display various signal formats. For detailed signal specifications, see “HDMI® signal formats” on page 106. Supported Audio format, see “HDMI®input” on page 105 . 28 Connecting Your TV Connecting an HDMI® or DVI device to the HDMI® input To connect a computer to the HDMI® input, see “Connection to the TV’s HDMI® terminal” on page 32 To connect an HDMI® device, you will need one HDMI® cable (type A connector) per HDMI® device. v For proper operation, it is recommended that you use an HDMI® cable with the HDMI® Logo( ). ® v HDMI cables transfer both video and audio. Separate analog audio cables are not required (see illustration). TV back panel HDMI ® device 
(Sample Illustration) 32/40/50L1400U—HDMI® connections To view the HDMI® device video: Select HDMI 1 or HDMI 2 video input source on the TV. (Press the INPUT button on the remote control. For more information, see “Selecting the video input source” on page 49) To connect a DVI device, you will need: v HDMI® to DVI adapter cable For proper operation, the length of an HDMI® to DVI adapter cable should not exceed 9.8 ft (3m). The recommended length is 6.6 ft (2m). 29 Connecting Your TV HDMI® CEC connection TV back panel VIDEO L DVI/HDCP OUT AUDIO R IN IN OUT L R (Sample Illustration) 32/40/50L1400U—DVI connections To ensure that the HDMI® or DVI device is reset properly: v When turning on your electronic components, turn on the TV first, and then the HDMI® or DVI device. v When turning off your electronic components, turn off the HDMI® or DVI device first, and then the TV. EIA/CEA-861-D compliance covers the transmission of uncompressed digital video with high-bandwidth digital content protection, which is being standardized for reception of highdefinition video signals. Because this is an evolving technology, it is possible that some devices may not operate properly with the TV. HDMI® CEC connection You can control the basic functions of connected audio/video devices using the TV’s remote control if you connect a HDMI® CEC compatible audio receiver or playback device. The HDMI® CEC Control feature uses CEC technology as regulated by the HDMI® standard. 30 Connecting Your TV HDMI® CEC connection Back panel Audio Receiver Playback device (HDMI ® CEC DVD Player, etc.) Playback device (HDMI ® CEC DVD Player, etc.) (Sample Illustration) 32/40/50L1400U—HDMI® CEC compatible audio receiver and playback device connections To connect an HDMI® device, you will need one HDMI® cable (type A connector) per HDMI® device (see “Overview of cable types” on page 22) v If several devices are connected, HDMI® CEC Control feature may not operate properly. v For proper operation, it is recommended that you use an HDMI® cable with the HDMI® Logo ( ). Before controlling the device(s): v After completing the above connections, configure the HDMI® CEC Setup menu with the desired settings, see “Setting up HDMI® CEC” on page 90 v The connected devices must also be configured. For details, see the operation manual for each device. v This feature uses the CEC technology as regulated by the HDMI® standard. v This feature is limited to models incorporating Toshiba’s HDMI® CEC. However, Toshiba is not liable for those operations. Refer to the individual instruction manuals for compatibility information. This feature may not work properly depending on the devices that are connected.  31 Connecting Your TV Connecting a digital audio system The TV’s Digital Audio Out terminal outputs a Dolby® Digital or 2-channel down-mixed PCM (pulse-code modulation) signal for use with an external Dolby® Digital decoder or other external audio system with optical audio input. You will need an optical audio cable (Use an optical audio cable that has the larger “TosLinkTM” connector and not the smaller “mini-optical” connector.) TV back panel Digital decoder or other digital audio system (Sample Illustration) 32/40/50L1400U—Connecting a digital audio system To control the audio: 1 Turn on the TV and the digital audio device. 2 Press the MENU button on the remote control and open the Sound menu. 3 Press the ▲/▼(arrow) buttons to select Digital Audio Output and then press the ENTER button. 4 Press the ◄/► (arrow) buttons to select either Auto or PCM, depending on your device. Some audio systems may not be compatible with Dolby® Digital bitstream signal.Older audio systems that are not compatible with standard optical out signals may not work properly, creating a high noise level that may damage speakers or headphones. THIS DAMAGE IS NOT COVERED BY YOUR WARRANTY. The DIGITAL AUDIO OUT terminal may not output some digital audio sources because of copy restrictions. v The Dolby® Digital format is available in the following situations: - When tuned to a digital RF channel - When an HDMI® input is used 32 Connecting Your TV Connecting a computer Connecting a computer With HDMI® connection, you can view your computer’s display on the TV and hear the sound from the TV’s speakers. Connection to the TV’s HDMI® terminal When connecting a computer with a DVI terminal, use an HDMI®to-DVI adapter cable. When connecting a computer with an HDMI® terminal, use an HDMI® cable (type A connector). Separate analog audio cables may not be necessary, depending on computer hardware and setup, see “Connecting an HDMI® or DVI device to the HDMI® input” on page 27 TV back panel Computer (Sample Illustration) 32/40/50L1400U Series - Connecting a computer to the TV through the HDMI® terminal. v The edges of the picture may be hidden. v If receiving a 480i (HDMI®), 480p (HDMI®), 720p, 1080i, or 1080p signal program, Native Mode TM scales the video to display the entire picture within the borders of the screen (i.e. no overscan). Chapter 3 Using the Remote Control Installing batteries To install batteries : 1 Remove the battery cover from the back of the remote control. Squeeze tab and lift cover (Sample Illustration) Removing the remote back cover 2 Insert two AAA batteries, corresponding to the (+) and (-) markings on the battery compartment. (Sample Illustration) Installing the batteries 3 Replace the battery cover. Do not expose batteries to excessive heat such as sunshine, fire, etc. 33 34 Using the Remote Control Remote control effective range v Be sure to use AAA size batteries. v Dispose of batteries in a designated disposal area. v Always consider the environment when disposing of batteries. v Always follow applicable laws and regulations. v If the remote does not operate correctly, or if the operating range is reduced, replace the batteries. v Always replace both batteries with new ones. Never mix battery types or use new and used batteries together. v Always remove batteries from the remote if they are dead or if the remote control is not to be used for an extended period of time. This prevents battery acid from leaking into the battery compartment. Remote control effective range For optimum performance, aim the remote control directly at the TV and make sure there is no obstruction between the remote control and the TV. 16.4 ft (5m) (Sample Illustration) 32L1400U-Remote control effective range  35 Using the Remote Control 16.4 ft (5m) (Sample Illustration) 40/50L1400U-Remote control effective range 36 Using the Remote Control Learning about the remote control Learning about the remote control The buttons used for operating the TV are described below. For the HDMI® CEC remote control functions, see “HDMI® CEC Blu-rayTM playback device (Blu-rayTM/DVD player, etc.) control” on page 87 (Sample Illustration) Remote control overview 37 Using the Remote Control Learning about the remote control The error message “NOT AVAILABLE” may appear if you press a button for a function that is not available. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 The POWER button turns the TV On/Off. When the TV is off, the power LED indicator on the TV front glows red. The PIC SIZE button cycles through the picture sizes, see “Selecting the picture size” on page 58 The PIC MODE button selects the picture mode, see “Adjusting the picture” on page 64 The INPUT button selects the video input source, see “Selecting the video input source” on page 49 The SLEEP button accesses the sleep timer, see “Setting the sleep timer” on page 86 The FREEZE button freezes the picture. Press again to restore the moving picture, see “Using the FREEZE feature” on page 63 The Channel Number buttons (0-9, and Dash 100) directly tune channels. The (Dash 100) button allows you to enter two part channel numbers, see “Storing channels in memory (optional)” on page 44 or to edit the Favorites List, see “Favorites browser” on page 53 The FAV button accesses the Favorites List in the Channel Browser, see “Favorites browser” on page 53 The RECALL button displays TV status information. The CH ▲/▼(arrow) buttons cycle through programmed channels (when no on-screen menu is present), see “Tuning channels using the Channel Browser” on page 52 The C. CAPTION button accesses closed captions, see “Using closed captions” on page 66 The MUTE button reduces or turns off the sound, see “Muting the sound” on page 68 The VOL (+ –) buttons adjust the volume level. The INFO button displays TV status information as well as program details, when available, see “Displaying TV status information” on page 91 The EXIT button closes on-screen menus. The ENTER button activates highlighted items in the main menu system. 38 Using the Remote Control Learning about the remote control 17 The CH RTN button returns to the last viewed channel or source, see “Switching between two channels using Channel Return” on page 57 18 The Arrow buttons (▲/▼/◄/►) select or adjust programming menus when a menu is on-screen. 19 The Arrow buttons (◄/►) open the Channel Browser and tune to the previous/next channel in the channel history when TV programming is on-screen. See “Tuning channels using the Channel Browser” on page 52 20 The MENU button accesses the main TV menu system. See “Navigating the menu system” on page 41. The following key functions allow you to control Toshiba HDMI® CEC compatible devices via HDMI® connection. See “Using HDMI® CEC” on page 87 21 The STOP button stops playback of the loaded playback device. 22 The PLAY button begins playback of the loaded playback device. 23 The SKIP forward button skips forward to locate later DVD chapters. 24 The FF button fast-forwards the playback device. (Press during play mode to view the picture moving rapidly forward.) 25 The EJECT button ejects the DVD or tape. 26 The PAUSE/STEP button suspends play or record temporarily. Press during play or record mode to pause the picture; press again to restart. 27 The SKIP reverse button skips to the beginning of the current DVD chapter or locates the previous chapter. 28 The REW button rewinds/reverses the playback device. (Press during play mode to view the picture moving rapidly backward.). Chapter 4 Menu Layout and Navigation Main menu layout The tables below and on the next pages provide a quick overview of your TV’s menu system. To open the menus (illustrated below), press MENU on the remote control. Icon Picture Item Picture Mode Option Dynamic / Standard / Movie / Game / PC / Store NOTE Store Mode is only available if the TV is set to Store Mode at initial setup. This option is hidden in the Home Mode. NOTE When the TV is set to Store in the initial menu or Store in the Installation Menu, the set will always reset to Store Picture Mode. Reset Reverts to the factory defaults for the selected picture mode Backlight Adjusts Backlight Contrast Adjusts Contrast Brightness Adjusts Brightness Color Adjusts Color Tint Adjusts Tint Sharpness Adjusts Sharpness Advanced Picture Settings Opens the Advanced Picture Settings menu Display Settings Opens the Display Settings menu 39 40 Menu Layout and Navigation Main menu layout Icon Sound Options Installation Timers Item Balance Bass Treble DTS TruSurround Sound Mode Stable Sound Dynamic Range Control TV Speakers MTS Digital Audio Selection Primary Audio Language Digital Audio Output Channel Options Closed Captions MediaShare Setup HDMI CEC Control Setup HDMI CEC Player Control Input Options Channel Browser Setup Power Management Panel Lock HDMI Information Display Parental PIN Setup Parental Control and Locks Menu Language Time Zone Daylight Saving Time Store / Home Mode Channel Tuning Quick Setup Reset TV Sleep Timer Game Timer Option Adjusts Balance Adjusts Bass Adjusts Treble On / Off Standard/Music/Movie/Clear Voice On / Off On / Off On/Off Stereo / Mono / SAP Offers different audio choices for digital channels Primary audio choice for digital channels Opens the Digital Audio Output menu Opens Channel Options menu Opens Closed Captions menu Opens MediaShare Setup menu Opens HDMI CEC Control Setup menu Opens HDMI CEC Player Control menu Opens Input Options menu Opens Channel Browser Setup menu Opens Power Management menu On / Off On / Off Opens Parental PIN Setup menu Opens Parental Control and Locks menu English / Français / Español Eastern / Newfoundland / Atlantic / Hawaii / Alaska / Pacific / Mountain / Central On / Off Home / Store Opens Channel Tuning menu Executes Quick Setup Resets to Factory Defaults 10-minute increments, from 0 min to a maximum of 12 hours Off/30 min/60 min/90 min/120 min 41 Menu Layout and Navigation Navigating the menu system Icon Item System Information Auto Demo Get Help Option Opens the System Information screen Opens Auto Demo menu NOTE Only available if the TV is set to Store mode. Navigating the menu system You can use the buttons on the remote control to access and navigate your TV’s on-screen menu system. 1 Press the MENU button to open the menu system. (Sample Image) Navigating the menu system 2 3 4 5 When a menu is open, use the ▲/▼/◄/►(arrow) buttons on the remote control to move in the corresponding direction in the menu. Press the ENTER button to save your menu settings or select a highlighted item. A highlighted menu item appears in a different color in the menu. All menus close automatically if you do not make a selection within approximately 60 seconds. To close a menu instantly, press the EXIT button. The menu background may sometimes appear black, depending on the signal the TV is receiving. This is not a sign of malfunction. Chapter 5 Setting up your TV Initial Setup When you first turn on or reset the TV, the Initial Setup window will appear. 1 In the Menu Language field, press the ◄/►(arrow) buttons to select your preferred language. 2 Press the ▲/▼(arrow) buttons to select Time Zone.Then set your desired time zone, using the ◄/►(arrow) buttons and press the ENTER button. The Store / Home Mode settings window appears. 3 For normal home use, press the ◄/►(arrow) buttons to select Home, and then press the ENTER button. The ANT/CABLE In setup window appears. 4 Press the ◄/►(arrow) buttons to select the input source (Cable or Antenna), and then press the ENTER button. 5 Press the ENTER button to select Start Scan and continue with the Auto Tuning. You must select a Language and either Home/Store mode, before you can exit out of the Setup Menu. The EXIT button will not function until these selections have been made. 42 43 Setting up your TV Installation Installationsetup setupselection selection Installation setup selection Menu language You can choose from three different menu language settings (English, Français, and Español) for the on-screen display of menus and messages. To select the menu language: 1 Press the MENU button and open the Installation menu, then highlight Menu Language. 2 Press the ◄/►/▲/▼(arrow) buttons to select your preferred language. Installation Menu Language English English Time Zone Eastern Français Off Español Daylight Saving Time Store / Home Mode Home Channel Tuning Quick Setup Reset TV (Sample Image) Selecting the menu language 3 Press the EXIT button to close the Installation menu. ANT/CABLE IN This setting configures the input source for the ANT/CABLE terminal. 1 Press the MENU button and open the Installation menu. 2 Highlight Channel Tuning, and then press the ENTER button. (Sample Image) Installation - Setup selection 44 Setting up your TV Auto Tuning 3 Open the Channel Tuning menu, highlight ANT/CABLE In, and then press the ENTER button. (Sample Image) Channel tuning menu - Input configuration selection 4 Press the ▲/▼(arrow) buttons to select the input source (Cable or Antenna), and then press the ENTER button to save your new settings. Storing channels in memory (optional) To make sure your TV stops only on the channels you want when you press the ▲/▼(arrow) buttons on the remote control or the control panel, store those channels in the TV’s memory. Auto Tuning You can set up the TV to detect all active channels in your area and store them in its memory. Then you can manually add or erase individual channels from memory. v You must set up the ANT/CABLE input source before programming channels. See “ANT/CABLE IN” on page 43. v The automatic channel programming process will erase channels that were previously programmed into the TV’s memory. v To tune the TV to a channel not programmed in the channel memory, you must use the Channel Number buttons on the remote control. v Programming channels when the ANT/CABLE input is configured for Cable will take substantially longer than when the antenna input is configured for Antenna. This is normal; however, once channel programming is finished, you should not have to repeat the programming process again unless your Cable TV service lineup changes significantly.  45 Setting up your TV To program channels automatically: 1 Configure the antenna input source, if you have not already done so, see “ANT/CABLE IN” on page 43. 2 Press the MENU button and open the Installation menu. 3 Highlight Channel Tuning, and then press the ENTER button. (Sample Image) Setup menu - Installation selection 4 Highlight Auto Tuning, and then press the ENTER button to open the Channel Program menu to begin channel programming. ! Cable Scanning channels, please wait... 6% Number of Channels Found - 7 Scanning Analog Channels Channel - 9 Cancel (Sample Image) Installation menu - Channel selection The TV will automatically cycle through all the antenna/cable channels, and store all active channels in the channel memory. While the TV is cycling through the channels, the message “Scanning channels, please wait” appears. 5 To cancel channel programming, press the EXIT button on the remote control or highlight Cancel in the on-screen display, and then press the ENTER button. When channel programming is complete, press the CH ▲/▼(arrow) buttons to view the programmed channels. 46 Setting up your TV Setting channel skip Manual Tuning After storing channels in memory, you can manually enter channels if the physical channel is known. 1 Press the MENU button and open the Installation menu. 2 Highlight Channel Tuning and then press the ENTER button. 3 Highlight Manual Tuning and then press the ENTER button, the Manual Tuning form will appear. 4 Use buttons 0–9 on the remote control to enter the channel number (for example, 56) 5 Press the ENTER button to start Manual Tuning. Type: Description: ATV Analog channel. DTV Digital channel. Setting channel skip To prevent a channel from being viewed, you can set it to be skipped. 1 From the Options menu, highlight Channel Options, and then press the ENTER button. The list of channels appears. (Sample Illustration) Channel Options 2 Press the ▲/▼(arrow) buttons to select a channel position to be skipped, and then press the ENTER button . A check will appear in the box. To remove the check, press the ENTER button again. 47 Setting up your TV Setting the time zone To add a channel to the channel memory: v Highlight the checked box next to the channel number you wish to add, and then press the ENTER button to remove the check. You can also block specific channels so that they cannot be tuned until you unlock them. For information, see “Locking channels” on page 77. To manually add digital sub-channels on a physical channel: v Use the Channel Numbers and the (Dash 100) on the remote control to enter the channel number (for example, 56–1). If the channel is found, the number will be added to the list and the box will be unchecked. If the channel is not found, a message appears. Skipped channels cannot be selected with the CH ▲/▼(arrow) buttons; however, they can be accessed using the number keys on the remote control. Setting the AV input mode This setting determines the configuration of the shared AV input on your TV. You can set this input for either ColorStream HD or Video. Add the following descriptions: To set the AV Input mode: 1 From Options menu, highlight Input Options, and then press the ENTER button. 2 Press ▲/▼(arrow) buttons to select AV Input, and then press the ENTER button. 3 Press ▲/▼(arrow) buttons to select Video or ColorStream HD, and then press the ENTER button to save your new setting. Setting the time zone The Time Zone setup allows you to specify the correct time zone for your region. This feature allows the TV status information to display the correct time zone information for your viewing area. To set the time zone: 1 In the Installation menu, highlight Time Zone, and press the ENTER button. 48 Setting up your TV Viewing the system status 2 Press the ▲/▼(arrow) buttons to select the region, and then press the ENTER button. To set the Daylight Saving Time status: 1 In the Installation menu, highlight Daylight Saving Time, and press the ENTER button. 2 Press the ▲/▼(arrow) buttons to select On or Off, and then press the ENTER button. Viewing the system status 1 In the Get Help menu, highlight System Information, and then press the ENTER button. The related information appears. To close the screen and return to the Get Help menu: v Highlight Done in the Support Information screen, and then press the ENTER button. To return to normal viewing, press the EXIT button. Resetting Factory Defaults To reset all settings and channels to their factory default values: 1 Press the MENU button and open the Installation menu. 2 Highlight Reset TV, and then press the ENTER button. 3 Enter your PIN code (If a PIN code has been set). 4 A confirmation screen appears. Select Yes, and press the ENTER button. The TV will turn off automatically. To cancel the reset process, select No, and press the ENTER button. Chapter 6 Setting up your TV Selecting the video input source To select the video input source to view: 1 Press the INPUT button on the remote control or TV control panel. 2 Do one of the following: v Press 0-3. v Repeatedly press the ▲/▼(arrow) buttons on the remote control, and then press the ENTER button to change the input setting. v Repeatedly press the INPUT button to cycle through all the inputs. Stop pressing the INPUT button when the desired input is selected. 49 50 Setting up your TV Selecting the video input source (Sample Image) Input Selection screen v You can label the video input sources according to the specific devices you have connected to the TV, see “Labeling the video input sources” on page 51 v Sources can be “hidden,” see“Labeling the video input sources” on page 51 v “NO VIDEO” will appear randomly on the screen if no signal is received in video input mode. v If a CEC device is connected to an HDMI® input, the HDMI® CEC icon appears. If a HDMI® CEC device with HDMI® switching capability (e.g. Audio Receiver) is connected to the HDMI® input, press the INPUT button on the remote control repeatedly to highlight HDMI 1 or HDMI 2. If the connected CEC device has any connected devices, a separate device selection pop-up window appears: Audio Receiver Player (Sample Illustration) HDMI® setting pop-up window Press the INPUT button repeatedly to highlight the desired input source, and then press the EXIT button. v When you select HDMI® CEC input sources from the pop-up window using the INPUT button, some HDMI® CEC devices may automatically turn on. 51 Setting up your TV Labeling the video input sources v When selecting input sources using the ▲/▼(arrow)buttons, you will need to press the ENTER button to actually select a particular device from the pop-up window or wait 5 seconds after highlighting desired input. Labeling the video input sources You can label each video input source according to the type of device you have connected to each source. Choose from the following preset list of labels: v – – (default label) v Receiver v Cable v DVD v Game v PC v Recorder v Satellite v VCR v Blu-Ray v Hide (to hide an unused input in the Input Selection screen and in the Channel Browser Inputs list) To label the video input sources: 1 In Options menu, highlight Input Options and then press the ENTER button. 2 Highlight Input Labeling, and then press the ENTER button. 3 Press the ▲/▼(arrow) buttons to highlight the video source you wish to label. 4 Press the ◄/►(arrow) buttons to select the desired label for that input source. If a particular input is not used, Hide can be selected as the label. This will cause that input to be grayed out in the Input Selection screen and skipped over when you press the INPUT button on the remote control. (Sample Image) Input Labeling screen 52 Setting up your TV Tuning channels using the Channel Browser 5 To save the new input labels, highlight Done, and then press the ENTER button. To revert to the factory default labels, highlight Reset and press the ENTER button. Input labeling example: The screen below left shows the default Input Selection screen (with none of the inputs labeled as a specific device). The screen below (right) is an example of how you can label the inputs if you connected a VCR to ColorStreamTM HD, a video recorder to HDMI 1, and a DVD player to HDMI 2. VCR Recorder DVD No inputs labeled All inputs labeled (Sample Image) Input selection screens To clear the input labels: 1 2 3 In Options menu, highlight Input Options and then press the ENTER button. Highlight Input Labeling, and then press the ENTER button. Highlight Reset, and then press the ENTER button. Tuning channels using the Channel Browser The Channel Browser provides an easy navigation interface for all your channels and inputs. This feature allows you to: v Navigate and select entries. v Keep a list of your favorite channels, see “Favorites browser” on page 53 v Quickly surf and tune your recently viewed channels/inputs from the Channel Browser History List. v Surf via Browse mode (to immediately tune channels as you highlight them in the Channel Browser) or Select mode (to surf over channels in the Channel Browser before you select one to tune). v Quickly change inputs from the Inputs List. v Quickly select HDMI® CEC devices from the HDMI® CEC List. 53 Setting up your TV Favorites browser Favorites browser The Favorites Browser allows you to quickly set up a favorite channels/inputs list that is integrated into the Channel Browser. To add a favorite channel/input: 1 Tune to the channel or input. 2 Press and hold the FAV button for a few seconds. The channel or input is added to the beginning of the Favorites list on the left side of the Channel Browser. To delete a favorite channel/input: 1 Press the FAV button to open the Favorites browser list. 2 Highlight the channel or input to delete by pressing BACK CB or NEXT CB arrow buttons. 3 Press and hold the (Dash 100) button for a few seconds. The channel/input will be removed from the Favorites list. To set up the Channel Browser: 1 In the Options menu, highlight Channel Browser Setup, and then press the ENTER button. 2 Press the ▲(arrow) button to highlight Navigation, and then press the ◄/►(arrow) buttons to select either Browse Mode or Select Mode. (Sample Image) Channel browser setup screen 3 Press the ▼(arrow) button to highlight History List, ANT/ CABLE List, Input List, Favorites List or HDMI CEC List, and then press the ◄/►(arrow) buttons to select On or Off. v The History List will be cleared every time the TV is powered off. v HDMI® CEC List is automatically grayed out and set to Off when Enable HDMI® CEC is switched to Off. See “Using HDMI® CEC” on page 87 54 Setting up your TV Favorites browser 4 To save the new entries, highlight Done, and then press the ENTER button. To return to factory defaults, highlight Reset, and then press the ENTER button. To open the Channel Browser: v Press BACK CB or NEXT CB arrow buttons on the remote control. v Press the BACK CB arrow button to surf backward through the previously tuned channels in the History list, the channels in the ANT/CABLE channel list, the inputs in the Inputs list, the favorite channels/inputs in the Favorites list, or the HDMI® CEC devices in the HDMI® CEC List. v Press the NEXT CB arrow button to surf forward through the channel History, the ANT/CABLE channel list, the Inputs list, the favorite channels/inputs in the Favorites list, or the HDMI® CEC List. Elements of the Channel Browser 2 9 4 8 3 4 52 2 5 (Sample Illustration) Channel Browser elements 1 2 3 4 5 Current list (History, ANT/CABLE, Inputs, Favorites, or HDMI® CEC). Channel or input type. Channel or input currently being viewed. Channel or input that is currently highlighted in the browser. Channels stored in the Current List. 55 Setting up your TV Favorites browser To toggle among the available lists: After opening the Channel Browser, press the ▲/▼(arrow) buttons to toggle through the History, ANT/CABLE, Inputs, Favorites, or HDMI CEC options. v The Channel Browser opens in History List by default. Once another list has been selected, the Channel Browser will open in the last selected list. v If all lists are turned off, pressing BACK CB or NEXT CB arrow buttons or the FAV button will not display the Channel Browser. If Favorites List is turned off, the FAV button will have no effect. v Pressing the FAV button will display the Channel Browser Favorites list regardless of the last selected list in the Channel Browser. To tune to a channel or input in Browse mode: 1 While watching TV, press BACK CB or NEXT CB arrow buttons to display the Channel Browser and surf back to a previous item or surf forward to the next item in the list. In Browse mode, when you stop on an item in the Channel Browser, it is highlighted and the TV automatically tunes to the channel or input. 2 Press the EXIT button to close the Channel Browser. To tune to a channel or input in Select mode: 1 2 3 While watching TV, press BACK CB or NEXT CB arrow buttons to display the Channel Browser and surf back to a previous item or surf forward to the next item in the list. In Select mode, when you stop on an item in the Channel Browser, it is highlighted, but the TV is not turned to the channel until you press the ENTER button. Press the ENTER button to tune the TV to the highlighted item. Press the EXIT button to close the Channel Browser. 56 Setting up your TV Favorites browser Adding and clearing channels and inputs in the History List As a channel or input is tuned, the Channel Browser adds it to the History List and displays it on the right side of the Channel Browser. Previously tuned channels/inputs are shifted to the left, eventually moving off the left side. Press the BACK CB arrow button to surf backward through the previously tuned channels/inputs. Any channel or input that is tuned repeatedly will not be repeated in the History List, but instead is moved to the end of the list on the right side of the Channel Browser. v All channels that are tuned using the numeric buttons on the remote control. v All channels that are tuned using the ◄/►(arrow) buttons on the remote control. Whenever an item is selected that cannot be tuned (for various reasons), the TV will automatically tune to the previously viewed channel or input. Clearing channels from the History List: v Reconfiguring the ANT/CABLE input will clear the History List. see “ANT/CABLE IN” on page 43 v Turning off the TV will clear the History List. Tuning to the next programmed channel To tune to the next programmed channel, press the ◄/►(arrow) buttons on the remote control or TV control panel. This feature will not function until you have programmed channels into the TV’s channel memory, see “Storing channels in memory (optional)” on page 44 Tuning to a specific channel (programmed or unprogrammed) To tune analog channels: Press the Channel Number (0–9) on the remote control. For example, to select channel 125, press 1, 2, 5, and then press the ENTER button. Tuning digital channels: Press the Channel Number (0–9) on the remote control, followed by the (Dash 100) button, and then the sub-channel number. For example, to select digital channel 125-1, press 1, 2, 5, –, 1, and then press the ENTER button. 57 Setting up your TV Favorites browser If a digital channel is not programmed, either through the automatic channel scan or the Channel add function, see “Auto Tuning” on page 44, you will have to tune the RF channel using the Channel Numbers and the (Dash 100) button on the remote control. Switching between two channels using Channel Return The Channel Return feature allows you to switch between two channels without entering an actual channel number each time. 1 Select the first channel you want to view. 2 Select a second channel using the Channel Number buttons (and the (Dash 100) button if selecting a digital channel). 3 Press the CH RTN button on the remote control. The previous channel will display. Each time you press the CH RTN button, the TV will switch back and forth between the last two channels that were tuned. If you press the CH RTN button from a non-antenna input, the TV will return to the last-viewed input. Switching between two channels using SurfLock™ The SurfLock™ feature temporarily “memorizes” one channel to the CH RTN button, so you can return to that channel quickly from any other channel by pressing the CH RTN button. To memorize a channel to the CH RTN button: 1 Tune the TV to the channel you wish to program into the CH RTN button. 2 Press and hold the CH RTN button for a few seconds until the message “Memorized” appears on the screen. The channel has been programmed to the CH RTN button. 3 You can then change channels repeatedly, and when you press the CH RTN button, the memorized channel will be tuned. The TV will return to the memorized channel one time only. Once you press the CH RTN button and then change channels again, the CH RTN memory will be cleared and the button will function as Channel Return, by switching back and forth between the last two channels that are tuned.This feature also works for external inputs. 58 Setting up your TV Selecting the picture size Selecting the picture size You can view many program formats in several picture sizes— Native, 4:3, Full, TheaterWide 1, TheaterWide 2, TheaterWide 3, Normal, and Dot by Dot. The picture size illustrations are examples only. The format of the image (in any of the picture sizes) depends on the format of the signal you are currently watching. Select the picture size that displays the current program in the way that looks best to you. You can save separate picture size preferences for each input on your TV. To select the picture size: 1 Press the PIC SIZE button on the remote. 2 With the Picture Size menu displayed, do one of the following: v Repeatedly press the PIC SIZE button. v Press the corresponding number button (0-5) while the Picture Size menu is displayed. v Press the ▲/▼(arrow) buttons while the Picture Size menu is displayed. Some of the picture sizes may not be available depending on the receiving signal format (those will be grayed out in the Picture Size screen). Using these functions to change the picture size (i.e., changing the height/width ratio) for any purpose other than your private viewing may be prohibited under the Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability. If you select a TheaterWideTM picture size, the top and bottom edges of the picture (including subtitles or captions) may be hidden. To view these edges, adjust the Picture Position or try viewing the program in 4:3 or Full, see “Scrolling “Scrolling the the TheaterWideTM TheaterWideTM picture (TheaterWide 2 and 3 only)” on page 62 59 Setting up your TV Selecting the picture size Full The Full setting is for viewing in the 16:9 (480i, 480p) source programs. If receiving a squeezed 4:3 format program, the picture is stretched horizontally to fill the width of the screen but not stretched vertically. The Full setting is for viewing in 1080i, 1080p, and 720p program source. (Sample Illustration) Picture size - Full The edges of the picture may be hidden. TheaterWide 1 This setting is for viewing 4:3 format programs. (Sample Illustration) Picture size - TheaterWide 1 The center of the picture remains close to its original proportion, but the left and right edges are stretched horizontally to fill the screen. TheaterWide 2 This setting is for viewing letter box programs. (Sample Illustration) Picture size - TheaterWide 2, letter box 60 Setting up your TV Selecting the picture size The picture’s top and bottom edges may be hidden*. TheaterWide 3 This setting is for viewing letter box programs with subtitles. (Sample Illustration) Picture size - TheaterWide 3, letter box with subtitles The picture’s top and bottom edges are hidden*. * To view the hidden areas (such as subtitles or captions), see TM “Scrolling the TheaterWide picture TheaterWideTM picture(TheaterWide (TheaterWide2 2and and3 3only)” only)” on page 62 Native These settings are for viewing in 480i (HDMI®), 480p (HDMI®), 720p, 1080i, and 1080p signal programs). (Sample Illustration) Picture size - Native v If receiving a 1080i, 1080p, 720p, 480i (HDMI®), or 480p (HDMI®) signal program, the video is scaled to display the entire picture within the borders of the screen (i.e. no overscanning). v This is especially useful for external HD sources such as DVD movies, Video Games, or computer graphics. v The Native mode is supported only for HDMI® (1080i, 1080p, 720p, 480i, and 480p), ColorStreamTM (1080i and 720p), and ANT/CABLE (digital) inputs (1080i, 1080p, and 720p). v Depending on the input signal, the picture’s border may be hidden, displayed in black, or noisy. 61 Setting up your TV Selecting the picture size 4:3 (Sample Illustration) Picture size - 4:3 Some program formats will display with sidebars and/or bars at the top and bottom. Normal This setting is for viewing VGA, SVGA, XGA, WXGA, and SXGA sources. (Sample Illustration) Picture size - Normal This size is a non-stretched display. Some input signal formats will display with sidebars and/or bars at the top and bottom. Dot by Dot This setting is for viewing VGA, SVGA, XGA, WXGA, and SXGA sources. (Sample Illustration) Picture size - Dot by Dot Dot by Dot is a non-scaling display. Depending on the input signal format (VGA, for example) the picture may appear with sidebars and/or bars at the top and bottom. 62 Setting up your TV Using the Auto Aspect feature Scrolling the TheaterWideTM picture (TheaterWide 2 and 3 only) You can set separate scroll settings for the TheaterWide 2 and TheaterWide 3 modes for each input. To set the scroll settings: 1 In the Picture Menu, highlight Display Settings, and then press the ENTER button. 2 Highlight Picture Position, and then press the ENTER button. (The Picture Position will be available when Picture Size is TheaterWide 2 or TheaterWide 3.) (Sample Image) Picture menu - Theater Settings selection 3 4 The Picture Position screen will appear, press ◄/►(arrow) button to scroll the picture up and down as needed. To save the new settings, highlight Done, and then press the ENTER button. To revert to the factory defaults, highlight Reset and then press the ENTER button. The adjustment range is from -5 to +10. When receiving a signal at 480i resolution, the picture scroll function may have limited adjustment range. Using the Auto Aspect feature When this feature is set to On, the TV will automatically select the picture size when one of the following input sources is received: v A 480i, 480p, 720p, 1080i digital signal from the ANT/CABLE input. v 480i, 480p, 720p, 1080i, 1080p, or VGA (60Hz) signal from the HDMI® inputs. 63 Setting up your TV Using the FREEZE feature Aspect Ratio of Signal Automatic Aspect Size (automatically selected when Auto Source Aspect is On) 4:3 Normal 4:3 4:3 Letter Box TheaterWide 2 16:9 Full Full Not defined (no ID-1 data or HDMI® aspect data) The current picture size you selected, see “Selecting the picture size” on page 58 To turn on the auto aspect ratio feature: 1 Press the MENU button and open the Picture menu. 2 Highlight Display Settings, and then press the ENTER button. 3 In the Auto Aspect field, press the ENTER button, and then select On. To turn off the Auto Aspect ratio feature, Select Off in step 3 above. Using the 4:3 Stretch When 4:3 Stretch is activated, the TV displays 4:3 programs as a full-screen picture. 1 From the Picture menu, highlight Display Settings, and then press the ENTER button. 2 Press the ▲/▼(arrow) buttons to select 4:3 Stretch, and then press the ENTER button. 3 Press the ▲/▼(arrow) buttons to select On or Off, and then press the ENTER button This feature is available when Auto Aspect is set to On. Using the FREEZE feature To use the FREEZE feature: 1 When watching the TV, press the FREEZE button to freeze the picture. 2 To unfreeze the picture, press the FREEZE button again (or any other button). 64 Setting up your TV Adjusting the picture Using the FREEZE function for any purpose other than your private viewing may be prohibited under the Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability. If the TV is left in FREEZE mode for more than 15 minutes, the FREEZE mode will automatically release and the TV returns to normal video. Adjusting the picture Selecting the picture mode You can select your desired picture settings from the modes described below. Mode: Description: Dynamic Maximizes Contrast, Color Saturation, Sharpness, Gray Scale, and Brightness to create more vivid and dynamic images. Standard Standard picture settings. Movie Lower contrast for darkened rooms. Game Optimized for playing video games by displaying the images in their purest form (4:4:4) without the loss of color information. The result is superior image quality and shorter signal to screen time for a faster gaming experience. PC Optimized for viewing your personal computer. Store Mode is only available if the TV is set to Store Mode at initial setup. This option is hidden in the Home Mode. When the TV is set to Store in the initial menu or Store in the Installation Menu, the set will always reset to Store Picture Mode. PC mode is available for HDMI® only (grayed out for other input sources). 65 Setting up your TV Adjusting the picture To select the picture mode using the menu system: 1 Press the MENU button and open the Picture menu. 2 Highlight Picture Mode, and then press the ENTER button. (Sample Image) Picture menu - Mode selection 3 Press the ▲/▼(arrow) buttons to select the picture mode you prefer, and then press the ENTER button. Adjusting the picture quality You can adjust the picture quality (Contrast, Backlight, DynaLightTM, Brightness, Color, Tint, and Sharpness.) to your personal preferences. Selection Press (◄) Press (►) Backlight* darker lighter Contrast lower higher Brightness darker lighter Color paler deeper Tint reddish greenish Sharpness softer sharper * Backlight: adjusts the brightness of the entire screen. When in video mode and no signal is input, this selection is automatically set to 0. (Settings are stored in memory.) To adjust the picture quality: 1 Press the MENU button and open the Picture menu. 2 Press the ▲/▼(arrow) buttons to select the picture quality you wish to adjust ( Backlight, Contrast, Brightness, Color, Tint, or Sharpness), press the ENTER button. Then press the ◄/►(arrow) buttons to adjust the setting. 66 Setting up your TV Using closed captions To reset to the factory defaults: 1 Press the MENU button. 2 Select Picture ► Reset. 3 Press the ENTER button. A confirmation screen appears. 4 Press the ▲/▼ (arrow) buttons to select Yes, and then press ENTER. Any picture setting that you adjust affects the current input only. You can adjust the picture quality separately for each input. Depending on a Sharpness value, the Edge Enhancer effect may be reduced. Using closed captions Base closed captions Closed caption mode has two options: v Captions—An onscreen display of the dialogue, narration and sound effects of TV programs and videos that are closed captioned (usually marked “CC” in program guides). v Text—An onscreen display of information not related to the current program, such as weather or stock data (when provided by individual stations). To view captions or text: 1 In Options menu, highlight Closed Captions, and then press the ENTER button. 2 In the Closed Caption Display field, select On. 3 In the Analog CC Mode field, select the desired closed caption mode, and then press the ENTER button. To view captions, highlight CC1, CC2, CC3, or CC4. (CC1 displays translation of the primary language in your area.) (Sample Illustration) Viewing captions 67 Setting up your TV Using closed captions If the program or video you selected is not closed captioned, no captions will display onscreen. To view text, highlight T1, T2, T3, or T4. (Sample Illustration) Captions - text If text is not available in your area, a black rectangle may appear on screen. If this happens, set the Base CC Mode to Off. To turn off closed caption mode, select Off in step 2 above. A closed caption signal may not display in the following situations: v When a recording has been dubbed v When the signal reception is weak v When the signal reception is non-standard Digital CC settings You can customize the closed caption display characteristics by changing the background color, opacity, text size, type, edge, and color. v These settings are available for digital channels only. v You cannot set Caption Text and Background as the same color. To customize closed captions: 1 In Options menu, highlight Closed Captions, and then press the ENTER button. 68 Setting up your TV Adjusting the audio 2 3 4 Highlight Digital CC Settings, and then press the ENTER button. Press the ▲/▼(arrow) buttons to highlight the characteristic you wish to change, and then press the ◄/►(arrow) buttons to select the format for that characteristic. To save the new settings, highlight Done, and then press the ENTER button. To revert to the factory defaults, highlight Reset, and then press the ENTER button. Mode: Description Caption Size Auto, Small, Standard, Large Caption Text Type Auto, Default, Mono (with Serif), Prop. (with Serif), Mono (without Serif), Prop. (without Serif), Casual, Cursive, Small Capitals Caption Text Edge Auto, None, Raised, Depressed, Uniform, Left Drop Shadow, Right Drop shadow Caption Text Color Auto, Black, White, Red, Green, Blue, Yellow, Magenta, Cyan Text Foreground Opacity Auto, Transparent, Translucent, Flashing, Solid Background Color Auto, Black, White, Red, Green, Blue, Yellow, Magenta, Cyan Magenta, Cyan Text Background Opacity Auto, Transparent, Translucent, Flashing, Solid Caption Text Edge Color Auto, Black, White, Red, Green, Blue, Yellow, Magenta, Cyan Adjusting the audio Muting the sound Press the MUTE button to partially reduce (1/2 Mute) or turn off (Mute) the sound. Each time you press the MUTE button, the mute mode changes in the following order: 1/2 Mute, Mute, Volume, 1/2 Mute, etc. 1/2 Mute Mute (Sample Image) Levels of mute Volume 69 Setting up your TV Adjusting the audio If you modify items in the Sound menu while Mute is active, Mute is cancelled. Using the Digital Audio Selection You can use the Digital Audio Selection to conveniently switch between audio tracks on a digital channel (for those channels that have multiple audio tracks). This temporarily overrides the audio track chosen by the Primary Audio Language option under the Sound menu, see “Selecting stereo/SAP broadcasts” on page 69 1 Press the MENU button and open the Sound menu. 2 Highlight Digital Audio Selection, and then press the ENTER button. DTS TruSurround Sound Mode Stable Sound Standard Off Digital Audio Output (Sample Image) Sound menu - Digital Audio Selector selection 3 4 Press the ◄/►(arrow) buttons to select the desired service. Press the EXIT button. Selecting stereo/SAP broadcasts The multi-channel TV sound (MTS) feature allows you to output high-fidelity stereo sound. MTS also can transmit a second audio program (SAP) containing a second language, music or other audio information (when provided by individual stations). When the TV receives a stereo or SAP broadcast, the icon Stereo or SAP appears when the INFO button is pressed. The MTS feature is only available for analog signals on the ANT/CABLE input. To listen in stereo sound: 1 Press the MENU button and open the Sound menu. 2 Highlight MTS, and then press the ENTER button. 3 Select Stereo, and then press the ENTER button. 70 Setting up your TV Adjusting the audio v You can typically leave the TV in Stereo mode because it outputs the type of sound being broadcast (stereo or monaural). v If the sound is noisy, select Mono to reduce the noise. To listen to an alternate language on an ATSC digital station (if available), highlight the Primary Audio Language field in step 2 above, and then select the language you prefer. To listen to a second audio program on an analog station, if available, select SAP in step 2 above. v A second audio program (SAP) can be heard only on those TV stations that offer it. For example, a station might broadcast another language as a second audio program. If you have SAP on, you will see the current program on the screen but hear the other language instead of the program’s normal audio. v If you have SAP on and the station you are watching is not broadcasting a second audio program, the station’s normal audio will be output. However, occasionally there is no sound at all in SAP mode. If this happens, set the MTS feature to Stereo mode. Adjusting the audio quality You can adjust the audio quality by adjusting the bass, treble and balance. To adjust the audio quality: 1 Press the MENU button and open the Sound menu. 2 Press the ▲/▼(arrow) buttons to highlight the item you wish to adjust (Bass, Treble, or Balance), and then press the ENTER button. 3 Press the ◄/►(arrow) buttons to adjust the level. v ◄ makes the bass or treble weaker or increases the balance in the left channel (depending on the item selected). v ► makes the bass or treble stronger or increases the balance in the right channel (depending on the item selected). 71 Setting up your TV Adjusting the audio DTS TruSurround™ This technology delivers an immersive virtual surround sound experience over front facing speaker configurations, complete with rich bass, high frequency detail and clear dialog. To turn on DTS TruSurroundTM: 1 Press the MENU button and open the Sound menu. 2 Highlight DTS TruSurround field, and then press the ENTER button. 3 Press the ▲/▼(arrow) buttons to select On, and then press the ENTER button Sound Mode Select the Sound Mode your prefer. To select a Sound Mode: 1 Press the MENU button and open the Sound menu. 2 Highlight Sound Mode field, and then press the ENTER button. 3 Press the ▲/▼(arrow) buttons to select one of Sound Mode , and then press the ENTER button. Stable SoundTM The Stable SoundTM feature limits high volume levels and prevents the extreme changes in volume that can occur when channels are changed or a program switches to a commercial. To turn on Stable SoundTM: 1 Press the MENU button and open the Sound menu. 2 Highlight Stable Sound, and then press the ENTER button. 3 Press the ▲/▼(arrow) buttons to select On. Using the Dolby® Digital Dynamic Range Control feature You can further compress Dolby® Digital dynamic range, allowing you to switch from digital to analog broadcasts at the same dynamic range. To use the Dolby® Digital Dynamic Range Control: 1 Press the MENU button and open the Sound menu. 2 Highlight Dynamic Range Control, and then press the ENTER button. 3 Press the ▲/▼(arrow) buttons to select On, and then press the ENTER button. 72 Setting up your TV Using parental controls (for USA region) v This feature is available when the TV is tuned to a digital RF channel or an HDMI® input with the Dolby® Digital signal. Selecting the PIN code A PIN code is necessary for some menus. v The Parental Control and Locks menu is grayed out if no PIN has been set. Enter a new PIN code 1 2 3 Press the MENU button and open the Options menu. Highlight Parental PIN Setup, and then press the ENTER button. Use the number buttons to enter a 4-digit number. Confirm the code. Forgotten PIN code While the PIN code entering screen is displayed, press the INFO button four times within five seconds. The PIN code will be cleared and you can enter a new PIN code. Changing or deleting your PIN code 1 2 3 4 Press the MENU button and open the Options menu. Highlight Parental PIN Setup, and then press the ENTER button. Use the number button to enter a 4-digit number. Select Change PIN or Delete PIN. Press the ENTER button. Using parental controls (for USA region) Blocking TV programs and movies by rating (V-Chip) Some TV programs and movies include signals that classify the content of the program (as unsuitable for younger viewers). The V-Chip feature in this TV detects the signals and blocks the programs according to the ratings you select. 1 Press the MENU button and open the Options menu. 2 Highlight Parental Control and Locks, and then press the ENTER button. 3 Enter your four-digit PIN code. 73 Setting up your TV Using parental controls (for USA region) 4 5 Press the ▲/▼(arrow) buttons to highlight Enable Rating Blocking, and press ENTER button. Press the ▲/▼(arrow) buttons to select On, and then press the ENTER button. (Sample Image) Locks menu - Enable Rating Blocking selection 6 7 8 Press the ▼(arrow) button to highlight Edit Rating Limits, and then press the ENTER button. The Edit Rating Limits screen appears. For each desired selection, press the ▲/▼/◄/►(arrow) buttons to highlight the selection, and then press the ENTER button to select it. A box with an “X” is a rating that will be blocked. As you highlight a rating, a definition for the rating appears at the bottom of the screen. To save the new settings, highlight Done, and then press the ENTER button. This feature will be not available if no PIN code is set. Downloading an additional rating system In the future, an additional rating system may become available for use in selectively blocking TV programs and movies. The currently tuned station must be receiving a digital signal before an additional rating system can be downloaded. To download the additional rating system, if available: 1 Press the MENU button and open the Options menu. 2 Hihglight Parental Control and Locks, and then press the ENTER button. 3 Enter your four-digit PIN code. 74 Setting up your TV Using parental controls (for USA region) 4 5 6 7 Press the ▲/▼(arrow) buttons to highlight Enable Rating Blocking, and press the ENTER button. Press the ▲/▼(arrow) buttons to select On, and then press the ENTER button. Press the ▼(arrow) button to highlight Edit Rating Limits, and then press the ENTER button. The Edit Rating Limits screen appears. Highlight Alt RS, and then press the ENTER button. The Edit Alternate Ratings screen appears. v The ALT RS button will only be available if an additional rating system is currently available. v It may take several minutes for the TV to download the additional rating system. v The information displayed in the Alternate Ratings screen will depend on the configuration of the additional rating system available at the time of download. 8 For each desired selection, press the ▲/▼/◄/►(arrow) buttons to highlight the selection, and then press the ENTER button to select it. A box with an “X” is a rating that will be blocked. 9 To save the new settings, highlight Done, and then press the ENTER button. 10 In the Edit Rating Limits screen, highlight Done, and then press the ENTER button. v The additional rating system can only be downloaded one time. You will not be able to download any updates to the rating system should such updates become available. v The additional rating system is not designed, transmitted or controlled by the TV or Toshiba, nor is the availability of an additional rating system determined or controlled by Toshiba. Similarly, the rating of programs in an additional rating system is not determined, transmitted or controlled by the TV or Toshiba. v The additional rating system is an evolving technology; therefore, availability, content and format may vary. 75 Setting up your TV Using parental controls (for USA region) Rating system Independent rating system for broadcasters: Ratings: Description and Content themes: TV-MA Mature Audience Only (This program is specifically designed to be viewed by adults and therefore may be unsuitable for children under 17. L) Crude or indecent language S) Explicit sexual activity V) Graphic violence TV-14 Parents Strongly Cautioned (This program contains some material that many parents would find unsuitable for children under 14 years of age.) D) Intensely suggestive dialogue L) Strong, coarse language S) Intense sexual situations V) Intense violence TV-PG Parental Guidance Suggested (This program contains material parents may find unsuitable for younger children.) D) Some suggestive dialogue L) Infrequent coarse language S) Some sexual situations V) Moderate violence TV-G General Audience (Most parents would find this program suitable for all ages) TV-Y7, TV-Y7FV Directed to Older Children (This program is designed for children age 7 and above. NOTE: Programs in which fantasy violence may be more intense or more combative than other programs in this category are designated TV-Y7FV.) TV-Y All Children (This program is designed to be appropriate for all children) Independent rating system for movies: Ratings: X NC-17 R PG-13 PG G Description and Content themes: X-rated (For adults only) Not intended for anyone 17 and under Restricted (Under 17 requires accompanying parent or adult) Parents Strongly Cautioned (Some material may be inappropriate for children under 13) Parents Guidance Suggested (Some material may be not be suitable for children) General Audience (Appropriate for all ages) 76 Setting up your TV Using parental controls (for USA region) Indication other than rating system: Display: TV-NONE MPAA N/A NOT RATE (No rating appears) Description: TV None Movie Not Applicable Movie Not Rated No rating information is provided If you place an “X” in the box next to “None” Rated, programs rated “None” or “Not Rated” will be blocked; Programs that do not provide any rating information will not be blocked. Displaying ratings To display the rating of the program you are watching, press the INFO button on the remote control. If it is rated “None” the word “NONE” appears in the INFO screen. If rating information is not provided, no rating will appear in the INFO screen. TV - NONE (Sample Image) Rating Info screens Unlocking programs temporarily If you try to tune to a program that exceeds the rating limits you have set, the TV will enter program lock mode and a warning message appears on the screen. This program exceeds the rating limit you set. Push " MUTE " to enter PIN. (Sample Illustration) Warning - exceeded rating limit You can either temporarily unlock the program or select an unlocked program to watch. To temporarily unlock the program: 1 Press the MUTE button. 77 Setting up your TV Locking channels 2 Enter your four-digit PIN code, and then press the ENTER button. If the correct code is entered, the program lock mode is released and the normal picture appears. All locking will be enabled again when you change the channel. Using the input lock feature You can use the Input Lock feature to lock the video inputs (Video, ColorStreamTM HD, HDMI 1 and HDMI 2). You will not be able to view the input sources until you unlock the inputs. To lock/unlock the video inputs: Mode: Video Off 1 In the Options menu, highlight the Parental Control and Locks, and then press the ENTER button. 2 Enter your four-digit PIN code. 3 Highlight Input Lock, and then press the ENTER button. 4 Press the ▲/▼(arrow) buttons to select the level of video input locking you prefer (see table below for descriptions), and then press the ENTER button. Description: Locks Video, ColorStreamTM HD, HDMI 1 and HDMI 2. Unlocks all video inputs. Locking channels With the Lock feature, you can lock specific channels. Locked channels can only be accessed by entering the PIN code, see “Enter a new PIN code” on page 72 To lock channels: 1 From the Options menu, highlight Channel Options, and then press the ENTER button. 78 Setting up your TV Locking channels (Sample Illustration) Channel options 2 3 Press the ▲/▼(arrow) buttons to select a channel in the lock column. Press the ENTER button. PIN code entry will be required to set a locked channel. If the PIN code has not yet been set, a warning message appears. 4 A check appears in the box. 5 To remove the check, press the ENTER button. 6 Press the EXIT button. Using the GameTimerTM You can use the GameTimerTM to set a time limit for playing a video game (30–120 minutes). When the GameTimerTM expires, the TV enters Input Lock mode and locks out the input source for the video game device. To set the GameTimerTM: 1 In the Timers menu, highlight GameTimer, and then press the ENTER button. 2 Enter your four-digit PIN code. 3 Press the ▼(arrow) button to select 30, 60, 90 or 120 minutes, and then press the ENTER button. To cancel the GameTimerTM, select Off in step 3 above. To deactivate the Input Lock once the GameTimerTM has activated it: 79 Setting up your TV Locking channels v Set the Input Lock to Off, see “Using the input lock feature” on page 77 v A message appears when 10 minutes, 3 minutes, and 1 minute are remaining. v If the TV loses power with time remaining, the TV will enter Input Lock mode when power is restored (as if the GameTimerTM had been activated). To resume use, you must deactivate the Input Lock, see “Using the input lock feature” on page 77 Using the panel lock feature You can lock the control panel to prevent your settings from being changed accidentally (by children, for example). When Panel Lock is set to On, none of the controls on the control panel operate except the POWER button. To lock the control panel: 1 In the Options menu, highlight Panel Lock, and then press the ENTER button. 2 3 Enter your four-digit PIN code. Press the ▼(arrow) button to select On. When the control panel is locked and any button on the control panel (except the POWER button) is pressed, the message “NOT AVAILABLE” appears. (Sample Illustration) Locks menu - Panel Lock selection To unlock the control panel, select Off in Step 3 in this section or press and hold the VOLUME (–) button on the TV control panel for approximately 15 seconds until the volume icon appears. 80 Setting up your TV Using the Media Player Using the Media Player Using Media Player with a USB device You can enjoy photo or music content stored on a USB storage device. Photo Viewer specifications: v Data type: JPEG EXIF ver 2.1 v File format: JPEG v Maximum photo size: 6 MB v Maximum number of files: 500/folder v Maximum photo resolution: 4096 x 4096 pixels Music Player specifications: v File format: MP3 v Sampling frequency: 32 kHz, 44.1 kHz, 48 kHz v Bit rate: from 32 to 320 kbps v Maximum number of files: 500/folder Supported file system: FAT16 and FAT32 v Gently insert the USB device into the port and do not remove while viewing Media Player. v USB device: USB Mass Storage Class device (MSC) v Connectivity is not guaranteed for all devices. v Connect the USB device to the TV directly. v Do not use a USB Hub. v You must obtain any required permission from copyright owners to use copyright content. Toshiba cannot and does not grant such permission. v Depending on the file size and amount in your USB storage device, it may take some time to load before content is viewable. A message will display on-screen when files are loading from the USB storage device. v Only limited types of U3 USB device are supported. Therefore, it is suggested that you not use U3 USB with Media Player. v Non-supported characters will be replaced with a square. 81 Setting up your TV Using the Media Player Auto Start function When Auto Start is enabled, you will be asked if you want to start the Media Player when a USB device is inserted. If Auto Start is disabled, you must manually start the Media Player from the menu. To change the Auto Start setting: 1 In the Options menu, highlight MediaShare Setup, and then press the ENTER button. 2 Press the ▲/▼(arrow) buttons to highlight USB Auto Start. 3 Press the ◄/►(arrow) buttons to select On or Off. To open the Media Player There are two methods for starting the Media Player: auto start and manual start. Auto Start: 1 Gently insert a supported USB storage device to the USB port on the back of the TV. A prompt will appear. If you repeatedly insert and remove the USB connector, the prompt may not appear. 2 Press the ◄/►(arrow) buttons to select Yes, and then press the ENTER button. The Media Player menu appears. (If you select No, nothing happens.) (Sample Image) Media Player - open screen v The prompt will disappear after about 10 sec. v If Auto Start is set to Off, you can start the Media Player manually. Manual Start: 1 In the Options menu, highlight MediaShare Setup, and then press the ENTER button. 2 Press the ▲/▼(arrow) buttons to highlight Photo or Music, and then press the ENTER button. 82 Setting up your TV Using the Media Player (Sample Image) Media Play screen v The viewer will open even if there are no photo or music files. v While the Media Player is active, the main menus cannot be displayed. Viewing photo files There are three types of view modes: multi view, single view, and slide show. Within Slide show, you can skip forward, repeat, and set time interval. Multi View This view allows you to search for photos in a grid format. These pictures are displayed using thumbnail data in each image file. (Sample Image) Media Play - photos screen To use multi view: Press the ▲/▼/◄/►(arrow) buttons to move the highlight in one window. If all of the photos will not fit in one screen, the screen will move to the previous page when you press ◄ from the top left thumbnail. When you press ► from the bottom right thumbnail, the screen will move to the next page. You can also use the ▲/▼(arrow) buttons to page up or down the in photo list when there are more photos than will fit on one screen. 3 When you select a folder, press the ENTER button to move to the next layer, or press the CH RTN button to return to the previous layer. 83 Setting up your TV Using the Media Player 4 Press the ENTER button to view the selected photo in Single View mode. Single view In this view mode, only files located in the selected directory will be displayed. This view allows you to change the photo content manually. When you move from Multi View to the Single View, the currently selected photo is displayed. To use single view: v Press the ►(arrow) button to view the next photo. Press ◄ to view the previous photo. v Press ▲ to rotate the image 90° counterclockwise. Press ▼ to rotate the image 90° clockwise. Slide show This view allows you to watch a slide show of the photos. In this mode, only files located in the selected directory will be played. To use slide show: 1 Press the ENTER button in the Single View mode. 2 Press the ◄/►(arrow) buttons to view the previous or next photo. To set Interval Time and Repeat settings: 1 Press the MENU button to open the Quick Menu. 2 Press the ▲/▼(arrow) buttons to select either Interval Time or Repeat. 3 Press the ◄/►(arrow) buttons to adjust the setting and press the CH RTN button. Zoom and Picture size functions are disable. To close the Photo Viewer, press the EXIT button. The television will return to the last viewed channel or external input. 84 Setting up your TV Using the Media Player Playing music files You can listen to music from a list of available files. When listening to music files, you can select music lists, play, pause, stop, skip, repeat play, and adjust sound settings. (Sample Image) Media Play - music list After opening Media Player and selecting Music (see “To open the Media Player” on page 81) press the ▲/▼(arrow) buttons to select a file or folder. You can use the ▲/▼(arrow) buttons to page up or down the music list when there are more files than will fit onto one screen. 4 Select the desired folder and press the ENTER button to move to the next layer. Press the CH RTN button to move back to the previous layer. 5 With the desired file selected, press the ENTER button or the PLAY button to start playback. 6 Press the STOP button to stop playback v If playback finishes before STOP is pressed, the next file will automatically start to play from the beginning. v Depending on the file size, it may take some time for playback to begin. During playback you can do the following: v Press PAUSE to pause. v To resume normal playback, press PLAY. v To locate a specific file, press the SKIP Reverse or SKIP Forward button repeatedly. v To adjust volume, press the VOL (+ –) buttons. To play in fast reverse or fast forward, press REV or FF during playback. Each time you press REV or FF, the playback speed changes. 85 Setting up your TV Using the Media Player During playback, you can adjust the Sound menu functions from the Quick Menu. To set the repeat mode: 1 Press the MENU button to open the Quick Menu. 2 Press the ▲/▼(arrow) buttons to select Repeat. 3 Press the ◄/►(arrow) buttons to select Off, All or 1. 4 Press CH RTN. To close the Music Player, press EXIT. Viewing photo files and playing music files at the same time While viewing photo files, you can listen to music from a list of available files. 1 While viewing photos in the Single View or Slide Show mode, press the MENU button to open the Quick Menu. 2 Highlight Background Music and press the ENTER button. The music list appears. 3 Select a music file and press the ENTER button to start playback. 4 Press CH RTN twice to move back to photo view mode. The music is now playing in the background. Sorting photo or music files From the photos Multi View or from the music list, you can sort your photo or music folders and files. To sort photo or music folders and files: 1 From photo Multi View mode or from the music list, press the MENU button to open the Quick Menu. 2 Press the ▲/▼(arrow) buttons to select Sort. 3 Press the ◄/►(arrow) buttons to select Title, New, or Old to set the sorting rule. Title-File sorting rules: v Unicode priority v Numerical (0-9), Uppercase (A-Z), lowercase (a-z), Chinese 86 Setting up your TV Setting the sleep timer v Increasing order New-From new to old according to the date and time when the picture was taken. Old-From old to new according to the date and time when the picture was taken. During playback, you can adjust the Sound menu functions from the Quick Menu. The Sorting or Total Time display display may not be available in all cases. Setting the sleep timer You can set the sleep timer to turn off the TV after a set length of time (maximum of 12 hours). To set the sleep timer using the remote control: 1 Press the SLEEP button on the remote control to set the length of time until the TV turns off. 2 Repeatedly press the SLEEP button to increase the time in 10-minute increments, or press the ▲/▼(arrow) buttons to increase or decrease the time in 10-minute increments, to a maximum of 12 hours. To set the sleep timer using the on-screen menus: 1 In Timers menu, highlight Sleep Timer, and then press the ENTER button. Press the Number buttons to enter the length of time (maximum of 12 hours) and then press the ENTER button. Or press the ▲/▼(arrow) buttons to increase or decrease in 10-minute increments (maximum of 12 hours). If a power failure occurs, the sleep timer setting may be cleared. To display the time remaining until the TV turns off, press the SLEEP button. To cancel the sleep timer, repeatedly press SLEEP until it is set to 0 minutes. 87 Setting up your TV Using HDMI® CEC No Signal Power Down The TV will automatically turn itself off after 15 minutes when no signal is detected. You can change the setting to Off for the following purposes: v Low signal strength of analog channel (no signal detection) v Only Audio L/R is connected to external input to listen to music through the TV speakers. To change the no signal power down setting: 1 From the Options menu, highlight Power Management, and then press the ENTER button. 2 Highlight No Signal Power Down, and then press the ENTER button. 3 Press the ▲/▼(arrow) buttons to highlight the item you want to change, and press the ◄/►(arrow) buttons to select On or Off. v Default setting for this feature is On. v A warning message will appear 1 minute before the TV turns off. Using HDMI® CEC This is a new feature that uses CEC technology and allows you to control Toshiba HDMI® CEC compatible devices from the TV remote via HDMI® (see “HDMI® CEC connection” on page 29) When Enable HDMI CEC Control in the HDMI CEC Control Setup menu is set to On (see “Setting up HDMI® CEC” on page 90), the HDMI® CEC functions described below will be enabled. HDMI® CEC playback device (Blu-rayTM/DVD player, etc.) control With your TV’s remote control, or using the HDMI® CEC Player Control menu, you can control the connected HDMI® CEC playback device you are watching. Available remote control key functions Button: PLAY STOP PAUSE SKIP Forward SKIP Reverse Description: Begin playback Stop playback Pause the picture during play or record mode Skip Forward Skip backward 88 Setting up your TV Using HDMI® CEC Button: FF REW ▲/▼/◄/► ENTER EXIT Description: Fast forward Rewind/reverse Navigates menu options Enters menu options Return to the previous menu These functions depend on the devices connected. HDMI® CEC Player Control menu functions To control the HDMI® CEC player from the menu: 1 From the Options menu, highlight HDMI CEC Player Control, and then press the ENTER button. (Sample Image) Preferences menu - HDMI® CEC Player Control 2 Press the ▲/▼(arrow) buttons to select the item you wish to control and press the ENTER button. Item: Description: Power Turns the select device On/Off Root Menu Accesses the root menu of the selected device Contents Menu Accesses the contents list when you press ENTER. At this time, the HDMI CEC Player Control menu disappears. Setup Menu Accesses the setup menu of a selected device Top Menu Accesses the top menu of a selected device Menu Accesses the menu of a selected device 89 Setting up your TV Using HDMI® CEC These functions depend on the devices that are connected.The HDMI® CEC Player Control item will be grayed out in the following conditions: v A non-HDMI® input is currently selected. v The Enable HDMI CEC item is set to Off. v The connected CEC device is not a playback or recording device. HDMI® CEC input source selection If a HDMI® CEC device with HDMI® switching capability (e.g. Audio Receiver) is connected to the HDMI® input, you can select another HDMI® CEC device that is connected to the master HDMI® device using the TV’s INPUT button, see “Selecting the video input source” on page 49 VOLUME and MUTE controls of Audio Receiver With your TV’s remote control, you can adjust or mute the sound volume of the Audio Receiver. v VOL (+ –) buttons adjust the volume level. v MUTE button turns off the sound. To use this function: v Set Initial Speaker Setting to Receiver in the HDMI CEC Control Setup menu. v Confirm that a connected HDMI® CEC device (such as DVD player, etc.) is selected for the Audio Receiver input source. v These functions depend on the device connected. v Initial Speaker Setting will be grayed out if Amplifier Control is set to Off. Other HDMI® CEC functions When the Enable HDMI CEC Control and each item in the HDMI CEC Control Setup menu are set to On, the following functions will be enabled. Item: TV Auto Power Description: If a HDMI® CEC device is turned on, the TV turns on automatically. Auto Standby If the TV is turned off, the TV will send a message to turn off all of the HDMI® CEC devices connected to the TV. 90 Setting up your TV Using the HDMI® settings feature Item: Amplifier Control Description: If Amplifier Control is set to On, you can adjust the sound volume or turn off the sound using the remote control. Initial Speaker Setting From this item, you can set your audio output preference to the TV speakers or the audio receiver speakers. When this item is set to Receiver, the TV remote can be used to adjust or mute the volume of the audio. This item will be grayed out when Amplifier Control is set to Off. When you turn on the Audio Receiver, change its input source or adjust the sound volume, the sound will be output from the audio receiver’s speakers even if TV Speakers has been selected. Turn the TV off and on again to output the sound from the TV speakers. Setting up HDMI® CEC To set the HDMI® CEC Setup: 1 From the Options menu, highlight HDMI CEC Control Setup and press the ENTER button. 2 Highlight Enable HDMI CEC Control, and then press the ENTER button. 3 Select On, and then press the ENTER button. If you select Enable HDMI CEC Control Off, the other items will be grayed out. 4 Press the ▲/▼(arrow) buttons to highlight the HDMI® CEC Setup item you want to use, and press the ENTER button, follow by ▲/▼(arrow) buttons. v TV Auto Power: On/Off v Auto Standby: On/Off v Amplifier Control: On/Off v Initial Speaker Setting: TV/ Receive Using the HDMI® settings feature HDMI® 1(or 2) RGB Range You can select RGB range of HDMI inputs from the following modes, as described below: 91 Setting up your TV Displaying TV status information 1 From the Options menu, highlight Input Options, and then press the ENTER button. 2 Highlight HDMI 1(or 2 ) RGB Range and then press the ENTER button. 3 Press the ▲/▼(arrow) buttons to select Auto, Full, or Limited, and then press the ENTER button. Mode Auto(default) Full Limited Description Adjusts RGB full range signal automatically. RGB input signal is displayed in the range from 0 to 255. RGB input signal is displayed in the range from 16 to 235. The HDMI® setting (RGB Range) needs proper HDMITM source devices. If your HDMI® source device does not support these features, the TV may not work properly when this feature is enabled. HDMI® Information Display Viewing the HDMI® signal information: 1 From the Options menu, highlight HDMI Information Display, and then press the ENTER button. 2 Press the ▲/▼(arrow) buttons to select On or Off, and then press the ENTER button. 3 When the HDMI Information is set to On, pressing the INFO button displays the HDMI Information banner (Resolution, Scan Type, Frame Rate, Aspect, Bit Depth, Color Space, RGB/ YUV, Chroma Format). When the HDMI Information is set to Off, the normal banner is displayed.  The signal information banner will appear when this feature is set to On and you watch an HDMI® input and press the INFO button. The signal information will disappear after approximately 60 seconds.  If you press the INFO button when this feature is set to Off, only the normal banner will appear. Displaying TV status information To display TV status information using the RECALL button: v Press the RECALL button on the remote control. The following information will be displayed (if applicable): v Current input (ANT/CABLE, Video, etc.) 92 Setting up your TV Understanding the last mode memory feature v If ANT/CABLE is the current input, either “CABLE” (for cable TV) or “ANT” (for over-the-air broadcasts). v Channel number (if in ANT/CABLE mode) v Digital signal strength indicator (bar graph in lower right corner of box; for digital signals only) v Stereo, Mono, or SAP audio status (when in HDMI® input mode, Dolby® Digital, or PCM) v Video resolution v Aspect ratio of incoming video signal (4:3 or 16:9) v V-Chip rating status v GameTimer (if set) To close the Recall screen, press the RECALL button again. To display TV status information using INFO, press the INFO button. The following additional information will display for digital channels, if applicable: v Title v Duration v Detailed description ANT 69-1 ABCD Now The ABCD Show Next ABCD New at 5:00pm 720p 16:9 TV-PG 05:00pm-06:00pm EST 08:00pm-09:00pm (Sample Illustration) Info banner To close the INFO screen, press the INFO button again. Understanding the last mode memory feature If the power is cut off while you are viewing the TV, the Last Mode Memory feature automatically turns on the TV when the power is resupplied. If you know you will be away from the TV for an extended period of time you should unplug the power cord. Chapter 7 Using the TV’s Advanced Features Using the advanced picture settings ColorMaster™ The ColorMaster™ feature allows you to adjust standard colors. 1 From the Picture menu, highlight Advanced Picture Settings, and then press the ENTER button. 2 Highlight ColorMaster, and then press the ENTER button. 3 Press the ▲/▼(arrow) buttons to select On, and then press the ENTER button. Base Color Adjustment When ColorMaster™ is set to On, the list of base colors appears. You can select a base color to adjust. 1 From the Picture menu, highlight Advanced Picture Settings, and then press the ENTER button. 2 Highlight Base Color Adjustment and then press the ENTER button. 3 Press the ▲/▼(arrow) buttons to select a color. Press the ENTER button. 4 Press the ◄/►(arrow) buttons to select Hue, Saturation, or Brightness. 5 Press the ▲/▼(arrow) buttons to adjust the setting. 93 94 Using the TV’s Advanced Features Using the advanced picture settings 6 Repeat Steps 3 through 5 to adjust other colors. To reset the adjustments to the factory defaults, select Reset on the screen. Press the ENTER button. Color Temperature You can change the quality of the picture by selecting from three preset Color Temperatures (Cool, Medium, and Warm), as described below. Mode: Picture Quality: Cool blueish Medium neutral Warm reddish 1 2 3 4 From the Picture menu, highlight Advanced Picture Settings, and then press the ENTER button. Highlight Color Temperature and then press the ENTER button. Press the ENTER button, follow by ▲/▼(arrow) buttons to select the desired color temperature, and then press the ENTER button. Press the ▲/▼(arrow) buttons to highlight Red, Green, or Blue level, and then press the ◄/►(arrow) buttons to adjust the level. Press the EXIT button. The Red, Green, and Blue level settings are connected to the Color Temperature settings and will change based on which preset color temperature (Cool, Medium, or Warm) is selected. Static Gamma The static gamma feature lets you adjust the levels of black in the picture. 1 From the Picture menu, highlight Advanced Picture Settings, and then press the ENTER button. 2 Highlight Static Gamma and then press the ENTER button. 3 Press the ◄/►(arrow) buttons to adjust the level of black detail. Press the EXIT button. v If the setting is decreased, the detail of black colors is decreased. v If the setting is increased, the detail of black colors is increased. 95 Using the TV’s Advanced Features Using the advanced picture settings DynaLightTM The DynaLightTM feature automatically strengthens the black coloring of dark areas in the video according to the level of darkness. 1 From the Picture menu, highlight Advanced Picture Settings, and then press the ENTER button. 2 Highlight DynaLight and then press the ENTER button. 3 Press the ▲/▼(arrow) buttons to select High, Low, or Off. Press the ENTER button. Dynamic Contrast Dynamic Contrast detects changes in picture quality that affect the appearance of your contrast settings and then automatically adjusts the video. 1 From the Picture menu, highlight Advanced Picture Settings, and then press the ENTER button. 2 Highlight Dynamic Contrast and then press the ENTER button. 3 Press the ▲/▼(arrow) buttons to select High, Middle, Low, or Off. Press the ENTER button. Cinema Mode When you view a DVD (3:2 pulldown processed) from a DVD player connected to the VIDEO, ColorStreamTM HD (component video), or HDMI® inputs on the TV, smoother motion can be obtained by setting the Cinema Mode to On. (available for 480i and 1080i signals). 1 From the Picture menu, highlight Advanced Picture Settings, and then press the ENTER button. 2 Highlight Cinema Mode and then press the ENTER button. 3 Press the ▲/▼(arrow) buttons to select On or Off. Press the ENTER button. Noise Reduction MPEG NR The MPEG noise reduction feature allows you to reduce visible interference caused by MPEG compression. 96 Using the TV’s Advanced Features Using the advanced picture settings 1 2 3 4 From the Picture menu, highlight Advanced Picture Settings, and then press the ENTER button. Highlight Noise Reduction and then press the ENTER button. Press the ▲/▼(arrow) buttons to select MPEG NR and then press the ENTER button. Press the ▲/▼(arrow) buttons to select High, Middle, Low, or Off, and then press the ENTER button. DNR DNR lets you soften the screen representation of a weak signal to reduce the noise effect. 1 From the Picture menu, highlight Advanced Picture Settings, and then press the ENTER button. 2 Highlight Noise Reduction and then press the ENTER button. 3 Press the ▲/▼(arrow) buttons to select DNR and then press the ENTER button. 4 Press the ▲/▼(arrow) buttons to select High, Middle, Low, or Off, and then press the ENTER button. Edge Enhancer The Edge Enhancer feature lets you adjust the levels for your desired picture settings and achieve a sharper picture. 1 From the Picture menu, highlight Advanced Picture Settings, and then press the ENTER button. 2 Highlight Edge Enhancer and then press the ENTER button. 3 Press the ▲/▼(arrow) buttons to select On or Off. Press the ENTER button. This feature may not work properly depending on the content. Chapter 8 Troubleshooting General troubleshooting Before calling a service technician, review this chapter or visit the Toshiba technical support Web site at support.toshiba.com for possible causes/solutions for the problem you are experiencing. Before you begin to troubleshoot any problem, first unplug the TV from the AC wall outlet, wait approximately one minute, and then plug the TV back into the AC wall outlet. If the problem still exists attempt to troubleshoot the problem. Black box on-screen. The closed caption feature is set to one of the Text modes (T1, T2, T3, or T4). Set the closed caption feature to Off, see “Using closed captions” on page 66 TV stops responding to controls. If the TV stops responding to the buttons on the remote control or TV control panel and you cannot turn off the TV, unplug the TV from the AC wall outlet and plug it back in. If you cause a static discharge when touching the TV and the TV fails to function, simply unplug the TV from the AC outlet and plug it back in. The TV should return to normal operation. Other problems. If your TV’s problem is not addressed in this Troubleshooting section or the recommended solution has not worked, use the Reset Factory Defaults procedure, see “Resetting Factory Defaults” on page 48 97 98 Troubleshooting Picture problems Onscreen Demo Pop-up If your TV is displaying a Demo pop-up screen, reset the Store / Home mode setting to Home. For more information see “Installation setup selection” on page 43 TV will not turn on. Ensure the power cord is plugged in properly, and then press the POWER button. Ensure the TV is plugged into a working AC power outlet by plugging another device into the AC power outlet to verify the AC power outlet is working. Replace the batteries in the remote control, see “Installing batteries” on page 33 Try the control panel buttons on the TV. Picture problems General picture problems. Check the antenna/cable connections, see “Connecting Your TV” on page 22 Press the INPUT button on the remote control or on the TV and select a valid video input source, see “Selecting the video input source” on page 49. If no device is connected to an input on the TV, no picture appears when you select that particular input source. For device connection details, see “Connecting Your TV” on page 22 Antenna reception may be poor. Use a highly directional outdoor antenna (if applicable). The station may be having broadcast difficulties. Try another channel. Adjust the picture quality, see “Using the advanced picture settings” on page 93 Picture size changes by itself or when the TV is turned OFF and back ON. Turn the Auto Aspect feature of the TV to OFF. see “Using the advanced picture settings” on page 93 Cannot select external video sources. If you cannot view signals from external devices connected to VIDEO, ColorStreamTM HD, HDMI 1, or HDMI 2, ensure that the Input Lock is set to Off, see “Using the input lock feature” on page 77 Troubleshooting Sound problems 99 Noisy picture. If you are watching an analog channel (off-air broadcast or Cable TV), you can set the DNR feature to reduce visible interference in the TV picture, see “DNR” on page 96 Video Input Selection problems If the Input Selection window does not appear when you press INPUT on the remote control or TV, press INPUT a second time. This will cause a change to the next video input source and display the Input Selection window. Poor display color or no color. The station may be having broadcast difficulties. Try another channel. Adjust the Tint and/or Color, see “Adjusting the picture quality” on page 65 Poor composite picture. If the TV is connected to an external A/V device (e.g. DVD player, video game system, set-top box, etc.) try using a ColorStreamTM or HDMI® video connection instead. Picture and sound are out of sync. As with all products that contain a digital display, this may occur in rare instances, when viewing certain content (e.g. television broadcasts, video games, DVDs). The cause may include, without limitation, video processing within the TV, video processing in an attached gaming system, and video processing or different compression rates used by broadcasters in their programming. Try the following: v If the TV is connected to an A/V receiver that has a programmable audio delay feature, use this feature to help synchronize the sound to the picture. v If the problem occurs only on certain TV channels, inform your local broadcast, cable, or satellite provider. v Turn off and unplug the TV from the AC wall outlet for a few seconds and plug it back in. Sound problems Check the antenna/cable connections, see “Connecting a VCR, antenna, cable TV, or camcorder” on page 24 The station may be having broadcast difficulties. Try another channel. The sound may be muted. Press the VOL (+) button. 100 Troubleshooting Channel tuning problems If you hear no sound, try setting the MTS feature to Stereo mode, see “Selecting stereo/SAP broadcasts” on page 69 If you are not receiving a second audio program from a known SAP source, make sure the MTS feature is set to SAP mode, see “Selecting stereo/SAP broadcasts” on page 69 If you hear audio that seems incorrect for the program you are watching (such as music or a foreign language), the SAP mode may be on. Set the MTS feature to Stereo mode, see “Selecting stereo/ SAP broadcasts” on page 69 Remote control problems Remove all obstructions between the remote control and the TV. Replace the remote control’s batteries, see “Installing batteries” on page 33 Your TV’s remote control may not operate certain features on your external devices. Refer to the User’s Guide for your other device to determine its available features. If your TV remote control does not operate a specific feature on another device, use the remote control that came with the device, see “Learning about the remote control” on page 36 If the TV still does not act as expected, perform the Reset Factory Defaults procedure, see “Resetting Factory Defaults” on page 48 Channel tuning problems The Auto Tuning feature may have erased the channel from memory. Add the channel to the channel memory, see “Storing channels in memory (optional)” on page 44 The Lock feature may have blocked the channel. Unblock the channel, see “Locking channels” on page 77 If you cannot tune digital channels, check the antenna configuration. If the problem persists, clear all channels from the channel list and reprogram channels into memory, see “Storing channels in memory (optional)” on page 44. For additional information, see “TV stops responding to controls.” on page 97. If the problem persists, use the Reset Factory Defaults procedure, see “Resetting Factory Defaults” on page 48 101 Troubleshooting No HDMI® CEC operation Closed caption problems If the program or video you have selected is not closed captioned, no captions appear on the screen.If text is not available, a black rectangle may appear. If this happens, turn off the closed caption feature, see “Using closed captions” on page 66 A closed caption signal may not display correctly under the following circumstances: v The recording is dubbed v The signal reception is weak v The signal reception is non-standard For additional information, see “Using closed captions” on page 66 Rating blocking (V-Chip) problems Forgotten PIN code. When the PIN code screen appears, press the INFO button 4 times within approximately 5 seconds. The old PIN code is cleared, see “Forgotten PIN code” on page 72 The V-Chip feature is available for U.S. V-Chip systems only, see “Using parental controls (for USA region)” on page 72 No HDMI® CEC operation The HDMI® CEC feature is available for Toshiba HDMI® CEC compatible devices. Ensure that HDMI® cables with the ( ) Logo are used. ® When the connected HDMI CEC device does not work correctly after you have changed settings of the device, turn off your TV and unplug the power cord, then plug in and turn on again. If several devices are connected, the HDMI® CEC feature may not operate properly. Read the instruction manual furnished with the connected HDMI® CEC device. 102 Troubleshooting If the problem persists after trying the solutions HDMI® problems HDMI® cables. Ensure that HDMI® cables with the ( ) Logo are used, see “Connecting an HDMI® or DVI device to the HDMI® input” on page 27 Legacy HDMI® sources. Some legacy HDMI® sources may not work properly with the latest HDMI® TV products due to new standard adoption. Media Player problems Incorrect functionality may occur when using a USB HUB connection. Photo files that were processed and edited using the computer’s application software may not be viewable. The TV may select one format automatically and play it when contents that support two or more formats are played. Confirm that the contents of the USB storage device are in formats that are supported by this TV, see “Using the Media Player” on page 80 If the problem persists after trying the solutions Contact Toshiba at: support.toshiba.com. Appendix A Specifications v These models comply with the specifications listed below. v Designs and specifications are subject to change without notice. v These models may not be compatible with features and/or specifications that may be added in the future. Television system NTSC standard ATSC standard Digital Cable 8VSB 64 QAM, 256 QAM; in-the-clear, unencrypted Channel coverage VHF UHF Cable TV 103 2 through 13 14 through 69 Mid band (A-8 through A-1, A through I) Super band (J through W) Hyper band (AA through ZZ, AAA, BBB) Ultra band (65 through 94, 100 through 135) 104 Specifications Power source Power source 120V AC, 60 Hz Power maximum current 32L1400U 40L1400U 50L1400U 0.9 A 1.1 A 1.4 A Power consumption 32L1400U 40L1400U 50L1400U 0.3 W in Standby mode 0.3 W in Standby mode 0.3 W in Standby mode Audio power 32L1400U 40L1400U 50L1400U 6 6 6 7W 7W 7W Speaker type 32L1400U Two 5.98 x 1.57 x 1.42” 40L1400U Two 5.98 x 1.57 x 1.42” 50L1400U Two 5.98 x 1.57 x 1.42” Video/audio terminals Video/audio input Video Audio 1 V (p-p), 75 ohm, negative sync. 200 mV(rms) (-20dBFS, 47K ohm or greater) 105 Specifications Dimensions (with stand) ColorStreamTM (component video) HD input Video Audio Y: 1V(p-p), 75 ohm PR: 0.7 V(p-p), 75 ohm PB: 0.7 V(p-p), 75 ohm Suggested formats: 1080i, 720p, 480p, 480i 200 mV(rms) (-20dBFS, 47K ohm or greater) HDMI®input HDMI® compliant (type A connector) HDCP compliant 2-channel Linear-PCM/ Dolby® Digital; 32/44.1/48kHz sampling frequency; 16/20/24 bits per sample HDMI® Audio Dimensions (with stand) 32L1400U 40L1400U 50L1400U Width Height Depth Width Height Depth Width Height Depth 28.9” (734mm) 19.3” (489mm) 7.1” (180mm) 36.5” (928mm) 23.1” (588mm) 7.6” (194mm) 44.2” (1122mm) 27.6” (702mm) 8.5” (217mm) Weight / mass (with stand) 32L1400U 40L1400U 50L1400U 13.4 lbs (6.1 kg) 20.9 lbs (9.5 kg) 35.1 lbs (15.9 kg) Operating conditions Temperature 32ºF - 95ºF (0ºC - 35ºC) 106 Specifications Supplied accessories 20 - 80 % (no moisture condensation) Humidity Supplied accessories v v v v v v Remote control with two size “AAA” batteries Resource Guide Quick Start Guide Pedestal and hardware Warranty information Power cord (available on certain models) Acceptable signal formats for HDMI® HDMI® signal formats Format Resolution V. Frequency H. Frequency Pixel Clock Frequency VGA 640 x 480 59.940 Hz 31.469 kHz 25.175 MHz SVGA 800 x 600 60.317 Hz 37.879 kHz 40.000 MHz XGA 1024 x 768 60.004 Hz 48.363 kHz 65.000 MHz 1280 x 768 59.870 Hz 47.776 kHz 79.500 MHz 1360 x 768 60.015 Hz 47.712 kHz 85.500 MHz SXGA 1280 x 1024 60.020 Hz 63.981 kHz 108.000 MHz 480i 720 x 480i 59.940 Hz 15.734 kHz 27.000 MHz 480p 720 x 480p 59.940 Hz 31.469 kHz 27.000 MHz 720p 1280 x 720p 60.000 Hz 45.000 kHz 74.250 MHz 1080i 1920 x 1080i 60.000 Hz 33.750 kHz 74.250 MHz 1080p 1920 x 1080p 24.000 Hz 27.000 kHz 74.250 MHz 60.000 Hz 67.500 kHz 148.500 MHz WXGA v Some illustrations in this User’s Guide are for explanation purposes and may differ from the actual unit. v Designs and specifications are subject to change without notice. v These models may not be compatible with features and/or specifications that may be added in the future. Appendix B Index A Acceptable signal formats for HDMI® HDMI® signal formats 106 Additional Safety Precautions Installation, Care, and Service Choosing a location for your LED TV To Display your LED TV on the included Pedestal Stand 4 Adjusting the picture Selecting the picture mode Adjusting the picture quality Using closed captions 64, 65 ANT/CABLE IN Storing channels in memory (optional) Auto Tuning Manual Tuning 43 Audio Adjusting quality 70 Dolby® Digital Dynamic Range Control 71 Muting sound 68 Stereo/SAP broadcasts 69 Auto Aspect using 62 Auto Start function Media Player 81 Available remote control key functions HDMI® CEC Player Control menu functions HDMI® CEC input source selection VOLUME and MUTE controls of Audio Receiver 87 B Base closed captions Digital CC settings Adjusting the audio Muting the sound 66 Blocking TV programs and movies by rating (V-Chip) Downloading an additional rating system Rating system 107 108 Index Displaying ratings 72 C Channel Browser elements 54 tuning channels 52 Channels Locking channels 77 Cinema Mode Noise Reduction MPEG NR DNR 95 Color Temperature Static Gamma DynaLightTM Dynamic Contrast 94 Component video cables (red/green/blue) HDMI® cable (with HDMI Logo) Optical audio cable About the connection illustrations 23 Connecting a digital audio system Connecting a computer Connection to the TV’s HDMI® terminal 31 Connecting a VCR, antenna, cable TV, or camcorder Connecting a Blu-ray™ / DVD player, satellite receiver with ColorStream® or VCR Connecting an HDMI® or DVI device to the HDMI® input HDMI® CEC connection 24 Connecting Your TV Overview of cable types Coaxial (F-type) cable Standard A/V cables (red/white/ yellow) 22 D Dimensions (with stand) Weight (mass) Operating conditions Supplied accessories 105 E Edge Enhancer 96 Enter a new PIN code Forgotten PIN code Changing or deleting your PIN code Using parental controls (for USA region) 72 F Favorites browser Elements of the Channel Browser Adding and clearing channels and inputs in the History List Tuning to the next programmed channel 53 Features 17, 18 Freeze Feature 63 Full TheaterWide 1 TheaterWide 2 TheaterWide 3 58, 59, 63, 91 H HDMI®-CEC using 87 HDMI® Information Display Displaying TV status information Understanding the last mode memory feature 91 I Icône Index sécurité 16 Introduction Safety icons Features Overview of installation, setup, and use 16 L Last mode memory feature 92 Locks menu setting pin code 72 M Media Player playing music files 84 Menu Navigation 41 Menu Layout and Navigation Main menu layout Navigating the menu system 39 N Native 4:3 Normal Dot by Dot 58, 60 No HDMI® CEC operation HDMI® problems Media Player problems If the problem persists after trying the solutions 101 No signal power down set 87 O Other HDMI® CEC functions Setting up HDMI® CEC Using the HDMI® settings 109 feature HDMI® 1(or 2) RGB Range 89 P Panel lock feature using 79 Parental controls using 72 Picture Adjusting quality 65 Picture size 4:3 61 Normal 61 TheaterWide 1 59 TheaterWide 2 59 TheaterWide 3 60 Pin code Changing 72 Deleting 72 Entering PIN code 72 Forgotten 72 Power maximum current Power consumption Audio power Speaker type 104 Program ratings Displaying 76 Unlocking programs 76 Q Quick setup ANT/CABLE IN 43 R Remote control problems Channel tuning problems Closed caption problems Rating blocking (V-Chip) problems 100 110 Index Resetting Factory Defaults 48 S Safety Icons 16 Safety Precautions WARNING CHILD SAFETY Important Safety Instructions 2, 4 Scrolling the TheaterWideTM picture (TheaterWide 2 and 3 only) Using the Auto Aspect feature Using the 4:3 Stretch Using the FREEZE feature 58, 60, 62 Setting channel skip Setting the AV input mode Setting the time zone Viewing the system status 46 Setting the sleep timer No Signal Power Down Using HDMI® CEC HDMI® CEC playback device (BlurayTM/DVD player, etc.) control 86 Setting up your TV Initial Setup Installation setup selection Menu language 42 Slide show Playing music files Viewing photo files and playing music files at the same time Sorting photo or music files 82, 83 Sound Mode Stable Sound Using the Dolby® Digital Dynamic Range Control feature Selecting the PIN code 71 Specifications Dimensions 105 HDMI® input 105 Speaker type 104 Supplied accessories 106 TV system 103 Specifications Television system Channel coverage Power source 103 T Timer Sleep timer 86 Time zone setting 47 To Display your LED TV using a Wall Bracket FCC Declaration of Conformity Compliance Statement (Part 15) ENERGY STAR® User Information Important notes about your TV 6 To open the Media Player Viewing photo files Multi View Single view 81 Trademark Information Copyright Notice 9 Troubleshooting Closed caption problems 101 Contact Toshiba 102 HDMI® 102 Media player problems 102 Picture problems 98 Rating blocking problems 101 Sound problems 99 Troubleshooting General troubleshooting Picture problems Index Sound problems 97 Tuning to a specific channel (programmed or unprogrammed) Switching between two channels Using Channel Return Switching between two Channels using SurfLock™ Selecting the picture size 56 TV front and side panel controls and connections TV back panel connections 19 TV panel controls left side 19 TV remote functionality 36 U Unlocking programs temporarily Using the input lock feature Locking channels Using the GameTimerTM 76 Using the Digital Audio Selection Selecting stereo/SAP broadcasts Adjusting the audio quality DTS TruSurround™ 69 Using the panel lock feature Using the Media Player Using Media Player with a USB device Auto Start function 79 Using the Remote Control Installing batteries Remote control effective range Learning about the remote control 33 Using the TV’s Advanced Features Using the advanced picture settings ColorMaster™ 111 Base Color Adjustment 93 V Video/audio terminals Video/audio input ColorStream® (component video) HD input HDMI®input 104 Video input sources Labeling 51
advertisement