LCD -based Intelligent Burglar Alarm System User Guide - QUACHNet

LCD -based Intelligent Burglar Alarm System User Guide - QUACHNet
LCD -based
Intelligent Burglar Alarm
System
User Guide
Ver 2.0
Table of Content
1.
2.
3
4
5
6
7
Introduction ............................................................................................................................... 2
1.1
General Description ...................................................................................................... 3
1.2
System Features ............................................................................................................ 3
Anatomy of the LCD-based Intelligence Burglar Alarm .......................................................... 4
2.1
System Components and Usage .................................................................................... 4
2.2
System Setup ................................................................................................................. 5
2.2.1
Panel Setup ........................................................................................................ 5
2.2.2
Connections of Cables....................................................................................... 6
Commands of LCD-based Smart Burglar Alarm System .............
!
3.1
Operation upon receiving alarming call ...............................
!
3.2
Remote Operation using phone .............................................................................. 7
3.3 Pre-record Voice Message ...................................................................................... 7
3.4 Add Remote Control ................................................................................................. 8
3.5
Delete the remote control ........................................................................................ 8
3.6
Add detector ............................................................................................................... 8
3.7
Delete detector ........................................................................................................... 8
Command Reference ............................................................................
!
4.1
Commands for Configuration .................................................
!
4.2
Commands of System Enquiries: ...........................................
!
Types of Alarm Zone ............................................................................................................... 20
6.1
Definitions of Zones................................................................................................... 20
6.2
System default zone types are: .................................................................................... 21
6.3
Fitting parameters: ...................................................................................................... 21
Guideline of Installation Sensors ............................................................................................ 21
6. 1 Guideline for Installing Door or Window Sensor ....................................................... 22
6.2
Guideline for Installing PIR Motion Sensor ............................................................... 22
Troubleshooting ...................................................................................................................... 23
1. Introduction
1.1 General Description
LCD –based Intelligent Burglar Alarm System is designed for both home and business
use and is built on leading microprocessor technology. This versatile system is also
equipped with powerful features and user-friendly interface as the most cost-effective
solution for security. It has a built-in siren with super high sound volume of 120 dB that
is loud enough as an alert for most noisy environment. The system allows at most 6
groups of phone number set up for calling notification that make sure you will not miss
any happening of incident. The LCD on panel displays clear system message and the
location of alert, together with the keypad on board, LCD-based Smart Burglar Alarm is
an in-dispensable choice of security solution for your properties and safety.
1.2 System Features
в– Large LCD English blue back-light display, voice prompt, ease of use.
в– Can check status and call records from panel.
в– Allow up to 99 wireless defense zones and 4 wired zones.
в– Each can be defined as one of the 8 zone types including NORMAL, STAY,
INTELLIGENT, EMERGENCY, CLOSED, HELP SENIOR, WELCOME and CHIME.
в– Four sets of scheduled arm/disarm function, each time disarmed you can select the
included period of time and different defense zone, eliminating of need of the manual
procedure, realizing the beauty of automatic controls
в– 6 group voice alarm phone number for alert calling, different zones can dial a pre-set
telephone number, and numbers saved inside EEPROM without lost upon power
failure.
в– Support ISD automatic voice mailbox for playback message upon alert. Maximum
length of voice message is 10 seconds.
в– Telephone (phone) long-distance telephone control for arming, disarming, monitoring,
remote announcement.
в– Wireless intelligent study coding, compatible with PT2262 normal encoding and a
1527 encoding, convenient and flexible for adding or reducing accessories. Maximum
support 150 remote control and 150 sensors.
в– Unique black box features, you can display most recent 72 disarmed records and 102 recent alarm
recording. Accurately shows the alarm time and zones number.
2. Anatomy of the LCD -based Intelligence Burglar Alarm
2.1 System Components and Usage
ARM
The system is at a fully ready status where all detectors are activated in a working state,
when the some events (burglar, fire, gas leak, etc) happened and detected, alarm system
alarm right away.
In a ARM status, the panel [ARM] light is on, LCD screen show "ARM" is also on.
To activate using remote control: press [ARM] key once.
To activate using keyboard: on panel keyboard [ARM] keys once
STAY ARM
This is for partial arming of the alarm system when there are people at home, only some
of the selected sensors are activated and could be triggered by events.
In a STAY ARM status, the panel [ ARM ] light is on, LCD screen show " Stay arm " is
also on.
To activate using remote control: press [Stay arm ] key once.
To activate using keyboard: on panel keyboard [STAY] keys once.
DISARM
All sensors are deactivated and will not be respond to any events.
In a DISARM status, the panel [ ARM ] light is off, LCD screen show " DISARM " is
on.
To activate using remote control: press [DISARM] key once.
To activate using keyboard: on panel keyboard [DISARM] keys once.
EMERGENCY
When an emergency occurs, press emergency button on the remote or the * button on
panel to activate alarm.
Remark:
If password on keyboard is enabled, you need to enter password before other operations,
the initial password is 1234.
2.2 System Setup
2.2.1
Panel Setup
Alarm panel should be installed at a central location with best transmission to all the
wireless sensors and accessories. Keep the panel well away from large metal objects or
household appliances with high-frequency interference, and avoid barriers such as
concrete walls with metal frame inside and fire doors.
Alarm panel
2.2.2
Connections of Cables
3. Commands of LCD-based Smart Burglar Alarm System
3.1.Operation upon receiving alarming call
After Panel alerts, it will automatically dial the preset telephone number for three times
until connected. When the user picks up the phone, a piece of pre-recorded voice
message will be played back immediately and let the receiver noted about the event.
Upon receiving the call, it can also control the alarm panel remotely via the phone
(according to the command below). User will not be asked for password upon
connected and alarm will automatically hang up call within receiving any instruction
within 20 seconds.
[1]: arming
[2]: disarming
[3]: monitoring open
[4]: monitoring closed
[5]: siren on
[6]: siren off
[7]: Monitor the voice message in mailbox
[*]: Hang up
3.2 Remote Operation using phone
Dial into the alarm panel using telephone or cellular phone can carry out some
operations remotely. Upon the panel pick up your call and connected, follow instruction
played to input password, (default password is 1234), press the corresponding number
on phone keypad for operation. Alarm will automatically hang up call after invalid
password failed for three times in succession.
[1]: arming
[2]: disarming
[3]: monitoring open
[4]: monitoring closed
[5]: siren on
[6]: siren off
[7]: Monitor the voice message in mailbox
[*]: Hang up
[#]enter the configuration mode
3.3 Pre-record Voice Message
Alarm panel will play a pre-recorded voice message after the alarm call when a pre-set
phone number upon alarm. To record customized message:
п‚· Press "# "Key to enter the configuration mode:
п‚· Then press 19#пјЊspeak your message at the panel for recording
п‚· System will record 10 Seconds and then automatically exit; or press any key to
end whenever your message end.
п‚· Press *, then # exit setup status.
3.4 Add Remote Control:
Press "#" key to enter the configuration mode:
п‚· Syntax: 07+(00~99)+# to configure remote control
Example: 07 then press 01#, to configure the 1st remote control. Then press any key of
the remote control to send a signal to the alarm panel, panel beep twice means
successful, beep only once means the remote control has been configured before. Alarm
panel can configure up to 150 remote control of different addressing. Upon completion
press # to exit the configuration mode, press * and then # exit the configuration mode.
3.5 Delete the remote control:
Press "# "Key to enter the configuration mode:
п‚· Syntax 1: 08+(00~99)+# to delete the remote control
п‚· Syntax 2: 08+**+# to delete all remote controls
Example: 08 then press 01# for deleting 1st remote control, then if you want to delete
8th remote control, press “08” instead of “01”. Press # to exit the delete remote control,
press * and then # to exit configuration mode.
3.6 Add detector
Press "# "Key to enter the configuration mode:
Syntax: 09+ (00~99) +# to set the detector
Example: 09 then press 01#, to configure 1st sensor, then trigger the detector to send a
signal to the alarm panel. Panel beep twice means successful, beep only once means the
remote control has been configured before. Alarm panel can configure up to 150
sensors of different addressing. Upon completion press # to exit the configuration mode,
press * and then # exit the configuration mode.
3.7 Delete detector
Press "# "Key to enter the configuration mode:
Syntax 1: 10+ (00~99) +# to delete the detector
Syntax 1: 10+**+# to delete all the detectors
Example: 10 then 01#, to deleting 1st sensor. If you want to delete the 6th detectors, use
“06” instead of “01”. Upon completion press # to exit the configuration mode, press *
and then # exit the configuration mode.
4
Command Reference
This system supports two methods of configuration including the local keyboard,
telephone set. Following are examples how instructions are given via one of the two
methods of setting
Example: you want to change the first phone number for voice calling to 13899998888:
Method 1: At the Keyboard
Press # to enter the configuration mode, and then press 3113899998888# , press the *
then press # to exit configuration mode.
Method 2: By telephone set
Calling into the alarm panel, upon connected, alarm panel will ask for password, it is
1234 as the default, then press #, and then press 3113899998888# , press the * then
press # to exit configuration mode.
Remark:
The status LED is lit on the panel to indicate at the configuration mode, the status light
is off upon exit.
Below is a table of all commands supported:
4.1 Commands for Configuration
Settings
Keypad Sequence & Parameters
Set up voice alarm
phone number
To set the 1st group to the 9th group of voice alarm phone
number гЂђ 1-9 гЂ‘ indicates that the first group to the Ninth
group alarm number correspondingly.
Example: If the user wants to set 13812345678 for the first set
of voice alarm phone number
Method one:
After you press the # key to enter the configuration mode, press
the 3113812345678#, * Then press # To exit Setup.
гЂђ 3 гЂ‘ + гЂђ 1-9 гЂ‘ Method two:
+ гЂђPhone numberгЂ‘ Remote calling into the alarm panel put in password (initial
password: 1234 ) when being asked, then press the # key, hear
+ гЂђ # гЂ‘
the voice prompt and then press 3113812345678#, then press #
to exit the remote setting status.
Remark:
For users using the telephone line extension, you should dial a
number (such as "9") to pick up a dialing tone, then with your
command you should add to this number a " * ". So the
completed command becomes 9*13812345678#
Remark:
7,8,9 group number for HELP SENIOR zone and panel will
only dial these three groups number when that specific zone
alarming.
Delete voice alarm
phone number
Used to delete the first groups to the Ninth group alert phone
numbers
Example: If you want to delete the first set of telephone alarm
гЂђ 3 гЂ‘ + гЂђ 1-9 гЂ‘ number,
+ гЂђ # гЂ‘
Method one:
After you press the # key to enter the configuration mode, press
the 31#, then press * then press # to exit Setup.
Method two:
After entering the telephone remote setting status, press 31#
Password
modification
Syntax:
гЂђ 50 гЂ‘ + "Four
digital
new
password" + гЂђ # гЂ‘
Set
delay
system arm
for
Syntax:
гЂђ
51 гЂ‘
+
гЂђ 00-99 Second "
+ гЂђ # гЂ‘
Set the time of
delay for alarming
Syntax:
гЂђ
52 гЂ‘
+
гЂђ 00-99 Second гЂ‘
+ гЂђ # гЂ‘
Used to modify the user password, the default user password is
1234
Example: If you want to set up a new user password 4321
Method one:
Press # key to enter the configuration mode, press the 504321#,
press the * then press # to exit setup.
Method two:
After calling and connected to the panel from remote, press
504321#
Upon armed from the remote control or alarm panel, the alarm
panel is set to delay 0 пјЌ 99 before at the ready status of ARM.
The system default is 00 seconds.
Example: users need to set the delay time for 60 Seconds.
Method one:
Press # key to enter the configuration mode, press the 5160#,
then * then press # to exit setup.
Method two:
After calling and connected to the panel from remote,
press5160#
Set the time of delay upon alarm, it can be set to 0-99 seconds;
the system default is 00 seconds.
Example: the user needs to set the alarm delay time to 60
Seconds.
Method one:
Press # Key to enter the configuration mode, press the 5260#,
and * then press # to exit setup.
Method two:
After calling and connected to the panel from remote, press
5260#.
Set length of Siren
sound
Syntax:
гЂђ
53 гЂ‘
+
гЂђ 00-20 Minute "
+ гЂђ # гЂ‘
Set the scope of
control of alarm
panel and remote
control
Syntax:
гЂђ
54 гЂ‘
+
гЂђ Remote control
number 00~99 гЂ‘ +
гЂђ Starting defense
area 00~99 гЂ‘ +
гЂђ End of defense
zone 00~99 гЂ‘ +
гЂђ # гЂ‘
Set
audible
confirmation
for
remote
control
operation
Syntax:
гЂђ
55 гЂ‘
+
гЂђ Remote control
number 00~99 гЂ‘ +
гЂђ 0/1 гЂ‘ + гЂђ # гЂ‘
Set alarm length of sounding when panel when the alarm, could
be set to 0-20 minutes, factory default is 1 minute.
Example: you want to make a siren sound 5 Minutes.
Method one:
# Key to enter the configuration mode, press the 5305#,
Then press # To exit Setup.
Method two:
After calling and connected to the panel from remote, press
5305#.
Set which defense zone will be controlled by remote control and
from alarm panel keyboard. Factory default is all remote control
and keyboard can control all 00-99 zones.
Remark:
The 1st remote control represented by number 01, ** represents
the alarm panel keyboard.
Example: you want to set 01 remote control to control only
00-20 zone.
Method one:
# Key to enter the configuration mode, press 54010020#
Method two:
After calling and connected to the panel from remote, press
54010020#
Example: you want to set the alarm panel keyboard control
00-50 Defense zone.
* Then press # To exit Setup.
Method two:
After calling and connected to the panel from remote, press
54**0050#
1 means on and 0 means closed, the default is on.
Example: set panel without sound when remote control number
01 is sending signal.
Method one:
Pressing # to entering the setup, and then press55010#, * then
press # to exit setup.
Method two:
After calling and connected to the panel from remote, press
55010#.
Set date and time Set the system date and time
settings
An example: it is now 1st of July of 2011 9 пјљ 00 пјљ 00 am
Method one:
Syntax:
гЂђ56гЂ‘ + "4-digits # to enter the configuration mode, press the
year" + гЂђ01-12 The 5620110701090000# пјЊ * then press # to exit Setup.
MonthгЂ‘ + гЂђ01-31 Method two:
DayгЂ‘ + гЂђ 00-23 After calling and connected to the panel from remote, press
HourгЂ‘ + гЂђ 00-60 5620110701090000#.
minutes гЂ‘
+
гЂђ 00-59 Second "
+ гЂђ # гЂ‘
Scheduled arm and
disarm time setting
Syntax:
гЂђ 57 гЂ‘ + Group
number гЂђ 01~04 гЂ‘
+
гЂђ
AAAA
Scheduled time of
arm гЂ‘ + гЂђ BBBB
Scheduled disarmed
time гЂ‘ + гЂђ Number
week гЂ‘ + гЂђ # гЂ‘
Scheduled arm and
disarm zones settings
Syntax:
гЂђ 58 гЂ‘ + гЂђGroup
number 01~04 гЂ‘ +
гЂђ 00-99 Defense
zone begin the area
code гЂ‘ + гЂђ 00-99
Defense zone ends
area code гЂ‘
+
гЂђ # гЂ‘
To set the time for scheduled arm and disarm, it allows set at
most four group of time for arm and disarm.
Example: set up the first group scheduled time to arm at 22 пјљ
00 pm and disarm at 07 пјљ 00 am, this is valid for Monday,
Tuesday, Wednesday, Thursday and Friday of each week.
Method one:
# enter the configuration mode, and then press
57012200070012345#
Example: set up the second group scheduled time to arm at
12 пјљ 00 and disarm at 13 пјљ 00 pm, this is valid for all 7 days
of each week.
Method one:
# enter the configuration mode, and then press
5702120013001234567#, * then press # to exit Setup.
Method two:
After calling and connected to the panel from remote,
press57012200070012345#,then press5702120013001234567#.
Used to set when the four group of zone to be controlled by
scheduled arm and disarm
Example: To set up the first group scheduled arm and disarm
control 00-50 defense zone.
Method one:
Press # enter the setup status and press 58010050#, * then press
# exit Setup
Method two:
After calling and connected to the panel from remote, press
58010050#
Used to set when the four group of zone to be controlled by
scheduled arm and disarm
Example: To set up the first group scheduled arm and disarm
control 00-50 defense zone.
Method one:
Press # enter the setup status and press 58010050#, * then press #
exit Setup
Method two:
After calling and connected to the panel from remote, press
58010050#
Set the type of
defense zone
Syntax:
гЂђ 60 гЂ‘ + гЂђ 00-99
zone number гЂ‘ +
гЂђ 1-8 Type гЂ‘ +
гЂђ 0/1 гЂ‘ + гЂђ # гЂ‘
To set 99 zone type, 00-99 represents 0-99 zone number, 1-8
represents one of the 8 zone type:
1. NORMAL
2. STAY ARM
3. INTELLIGENT
4. EMERGENCY
5. CLOSED
6. CHIME
7. WELCOME
8. HELP SENIOR
The last 0/1 represents 0 siren of panel produce no sound
upon alarming while 1 is sounded.
Example: Set zone number 2 as STAY zone type, and siren not
sound upon alarming.
Method one:
# Key enters the configuration mode, press 600220#,
* Then press # To exit Setup.
Method two:
After calling and connected to the panel from remote, press
600220#
Set mode of wired Set wired alarm zone to NO or NC. The zone numbers of
alarm zone
51-54 are wired defense zones, system default is 51-54 are
wired zones with NO mode.
0 means NO and 1 means NC
Syntax:
Example: Set 51 zone to NC,
гЂђ 61 гЂ‘ + гЂђ zone
Method one:
number 51-54 гЂ‘ +
# Key enters the configuration mode, press 61511#
гЂђ0/1 гЂ‘+ гЂђ# гЂ‘
* Then press # to exit Setup.
Method two:
After calling and connected to the panel from remote, press
61511#
Remark: On the back pane of the alarm panel
51 = zone 1 and labeled Z1
52 = zone 2 and labeled Z2
53 = zone 3 and labeled Z3
54 = zone 4 and labeled Z4
Set
Remote This enables or disables the remote operation of alarm panel
Operation on or off using telephone. System default is on.
Example: turn off the remote setting function,
Syntax:
гЂђ62 гЂ‘+ гЂђ0/1 гЂ‘ Method one:
#, and then press 620#, * then press # To exit Setup.
+ гЂђ# гЂ‘
Method two:
After calling and connected to the panel from remote, press
620#
Assign
specific System default is all 00-99 defense zone will make call from
phone number to the first to sixth group phone number upon alarming.
certain zone
Example: user needs 00-10 to call the first, second, third set
of numbers.
Syntax:
гЂђ
63 гЂ‘
+ Method one:
гЂђ 00-99 Defense # , and then press 630010123#
zone begin the area Method two:
code гЂ‘ + гЂђ 00-99 After calling and connected to the panel from remote, press
Defense zone ends 630010123#
area code гЂ‘ + Example: users need to 11-20 zone alarm the fourth, the fifth
гЂђ Police group and the sixth group number.
number 123456 гЂ‘ Method one:
# , And then press631120456#
+ гЂђ # гЂ‘
Method two:
After calling and connected to the panel from remote, press
631120456#
Example: User wants zone 21 calls only the 5th group
number.
Method one:
# And then press6321215 #.
Method two:
After calling and connected to the panel from remote, press
6321215#.
Set
audible
confirmation from
panel to on or off
Syntax:
гЂђ
11 гЂ‘
+
гЂђ 0/1 гЂ‘ + гЂђ # гЂ‘
Alarm panel will produce audible confirmation beep upon
receipt of signal from remote control. 1 is on, 0 is off, and
default is on.
Example: users need to disable the audible confirmation.
Method one:
# then press 110# , press the * then press # Exit Setup
Method two:
After calling and connected to the panel from remote, press
110#
Enable or disable of
the anti-tampering
of telephone cord
Syntax:
гЂђ
13 гЂ‘
+
гЂђ 0/1 гЂ‘ + гЂђ # гЂ‘
Cut the phone cord will trigger the alert. 0 is off and 1 on,
system defaults to closed.
Example: user need to enable anti-tampering of telephone
cord feature
Method one:
Press # Then press 131#, * then press # to exit Setup
Siren
volume
adjustment
Syntax:
гЂђ
14 гЂ‘
+
гЂђ 00-99 гЂ‘ +
гЂђ # гЂ‘
Forced disarm from
panel keyboard
Syntax:
гЂђ
15 гЂ‘
+
гЂђ 0/1 гЂ‘ + гЂђ # гЂ‘
Method two:
After calling and connected to the panel from remote, press
131#
Valid value is from 00 to 99 as largest, system default is the
largest.
Example: users need to set volume to 50 гЂ‚
Method one:
# , and then press 1450# , press the * then press # Exit Setup
Method two:
After calling and connected to the panel from remote, press
1450#
Upon alarming, enforced to use only the panel keyboard to
disarm (remote control is not allowed) for extra security. 1 is
on and 0 is off , the system default is off
Example: user needs to enforce to use keyboard.
Method one:
# , and then 151# , press the * then press # Exit Setup
Method two:
After calling and connected to the panel from remote, press
151#
Turn on or off This set the alarm panel to sound for 5 seconds upon a kind of
Interference Alert
malicious attach from un-authorized remote control or transmitter
of same frequency, meanwhile, the alarm panel will display tP
Syntax:
гЂђ
16 гЂ‘
+ warning.
гЂђ 0/1 гЂ‘ + гЂђ # гЂ‘ Example: users need enable interference alert
Method one:
# , and then press 161# ,
press the * then press # Exit Setup
Method two:
After calling and connected to the panel from remote, press 161#
Keyboard password To enable the password protect of keyboard. System default
protection feature
password is 1234, defaults set to off. Alarm panels will display
"keyboard locked" when keyboard is locked
Syntax:
гЂђ
17 гЂ‘
+ Example: keyboard users need to set the password protection.
гЂђ 0/1 гЂ‘ + гЂђ # гЂ‘ Method one:
# , and then press 171# , press the * then press # Exit Setup
Method two:
After calling and connected to the panel from remote, press 171#
Set number of ring The system default is 8.
tones
before 0 means the remote operation is not allowed and disabled
picking up
Example: the user needs to set up a number of rings before
picking up to 6.
Syntax:
гЂђ 18 гЂ‘ + гЂђ 00 Method one:
пјЌ 99 гЂ‘ + гЂђ # гЂ‘ # , and then press 1806#
Example: the user needs to set off the remote number ring.
Method one:
# , and then press 1800# , press the * then press # Exit Setup
Method two:
After calling and connected to the panel from remote, press
1806# ,or press 1800#
Restore
setting
factory System restore factory setting
Method one: # , and then press 9898#
Method two:
After calling and connected to the panel from remote, press9898#
Syntax:
Remark:
гЂђ 9898 гЂ‘ +
This feature will restore all settings to factory default apart from
гЂђ # гЂ‘
the configuration of sensors and remote control.
Total System Reset
Disconnect power to the alarm panel, turned off the battery switch
alarm panel, then press and hold the alarm panel of ARM button
Syntax:
while power-on. The system will respond with short “beep”
Press and hold the
slowly for 5 seconds, then can release ARM button. The system is
ARM button on the
now totally reset. All configurations have been cleared, all sensors
keyboard
and
and remote controlled are deleted and password is restored to
power on.
original 1234.
4.2 Commands of System Enquiries
Press Query button on panel to enter the query mode, alarm panel status LED is
blinking. Then put in commands as detailed in table below, when finished, Press *, and
then press #, to exit the query mode.
Note: In case keyboard password protection is enabled, please enter the password to
unlock before other commands.
Query for
voice To query the alarm panel currently saved to the first set to
alarm phone number the Ninth group voice alarm phone number.
Press alarm panel query key of your keyboard, then
Syntax:
3+гЂђ 1-9 гЂ‘ + гЂђ # гЂ‘ blinking status LED on the Panel, and then press 31#, the
alarm panel LCD show 13812345678 means alarm panel's
first set of alarm numbers are13812345678
Query password
Used to query the current password of the alarm panel,
Press alarm panel query key of your keyboard, then
Syntax:
blinking status LED on and then press 50#, the alarm panel
50 +гЂђ # гЂ‘
LCD show 1234. Alarm panel your current password is
1234. Press # to clear the screen, press * then press # to
exit the query mode.
Query the time for Query delay time for arm (00-99) Seconds
delay arm
Press alarm panel query key of your keyboard, then
blinking status LED on and then press 51#, the alarm panel
Syntax:
LCD show 00 mean time for delay is 0 second.
51 +гЂђ # гЂ‘
Query delay time for
alarming
Syntax:
52+гЂђ # гЂ‘
Query siren sounding
time for alarming
Syntax:
53+гЂђ # гЂ‘
To query the alarm delay time (00-99) Seconds
Press alarm panel query key of your keyboard, then
blinking status LED on and then press 52#, the alarm panel
LCD show 00 mean time for delay is 0 second.
To query the siren sounding time (00-20) minutes when the
alarming.
Press alarm panel query key of your keyboard, then
blinking status LED on and then press 53#, the alarm panel
LCD show 01 mean time for delay is 1 minute.
Query remote control For query of specific remote control and keyboard
and
keyboard assignments to zone 00-99
assignments to zone
Press alarm panel query key of your keyboard, then
Syntax:
blinking status LED on and then press 5401#, the alarm
54+ гЂђ 00-99 гЂ‘ + panel LCD show 00-99 and remote control 1 means remote
гЂђ # гЂ‘
control 1 is controlling zone 00-99, press # clear screen,
using 5402# for query remote control 2 and so on.
Query remote control For query the setting of remote control 00-99 for the
audible confirmation audible confirmation to command.
Press alarm panel query key of your keyboard, then
Syntax:
55+ гЂђ 00-99 гЂ‘ + blinking status LED on and then press 5501#, the alarm
panel LCD show ON means remote control 1 is set to
гЂђ # гЂ‘
sound upon receipt of command.
Query the scheduled Used to query first to fourth set of scheduled time for arm
time for arm and and disarm.
disarm
Press alarm panel query key of your keyboard, then
blinking status LED on and then press 5701# to query the
Syntax:
57+гЂђ 01 пјЌ 04 гЂ‘ + first of scheduled arm and disarm, the alarm panel LCD
show ” Monday, Tuesday, 22-00 07-00” means schedule
гЂђ # гЂ‘
set as Monday and Tuesday 22:00 pm arm and 07:00 am
disarm.
Query
the
zone For query the first to the fourth group scheduled arm and
number
with disarm.
scheduled arm and Press alarm panel query key of your keyboard, then
disarm
blinking status LED on and then press 5801# for zones
with the first group of phone zone, the alarm panel LCD
Syntax:
st
58+【 01 - 04 】 + show “00-99” means 0-99 zone are with 1 phone number
group.
гЂђ # гЂ‘
Query type wireless For query the zone types of 00-99.
defense zone
The alarm panel LCD show the name of type of zone,
detail about zone types can be referred to another section
Syntax:
60+【 00 - 99 】 + of manual, the word “ON” or “OFF” next to the zone type
represents whether siren will sound upon alarming.
гЂђ # гЂ‘
Query the type of
wired zones
Syntax:
61+гЂђ 51 пјЌ 54 гЂ‘ +
гЂђ # гЂ‘
Query
remote
operation on/off
Syntax:
62+гЂђ # гЂ‘
Query phone number
for specific zone
For query the zone type of 51-54.
Example: Press alarm panel query key of your keyboard,
then blinking status LED on and then press 6151# to query
51 zone alarm type, show NO means short-circuit to alarm
while show NC means open circuit to alarm.
To query if the remote operation is allowed, it should show
either ON or OFF.
To query the phone number assigned to zone 00-99 for
alert.
Syntax:
Example: Press alarm panel query key of your keyboard,
63+гЂђ 00 пјЌ 99 гЂ‘ + then blinking status LED on and then press 6301# for zone
гЂђ # гЂ‘
1, the alarm panel LCD show 123456 means these 6 group
of phone numbers are assigned to 01 zone.
Query for the setting For query whether the alarm will play audible confirmation
of alarm audible upon receipt of commands. It shows either ON or OFF.
confirmation
Syntax:
11+гЂђ # гЂ‘
Query the setting of For query whether the anti-tampering of telephone line is
anti-tampering
of set, it shows either ON or OFF.
telephone line
Syntax:
13+гЂђ # гЂ‘
Query sound volume Query for the volume level of siren, it shows between
of siren
00-99 representing the 00 as lowest and 99 as highest
volume.
Syntax:
14+гЂђ # гЂ‘
Query for the setting To query whether enforcing the disarm from keyboard
of enforced keyboard upon alarming. It shows either ON or OFF.
disarm
Syntax:
15+гЂђ # гЂ‘
Query of the setting
of interference alert
Syntax:
16+гЂђ # гЂ‘
Query
keyboard
password protection
Syntax:
17+гЂђ # гЂ‘
Query of number of
rings before panel
pick-up incoming call
Syntax:
18+гЂђ # гЂ‘
To query whether interference alert is set, it shows either
ON or OFF.
To query if the password protection feature is enabled, it
shows either ON or OFF.
To query the number of ringing before the panel will pick
up incoming calls from remote.
Example: Press alarm panel query key of your keyboard,
then blinking status LED on and then press 18#, it shows
08 means 8 rings, 11 means 11 rings and so forth.
Query alarm panel The system can save up to the most recent 72 disarmed
arm/disarm records
records.
Syntax:
9901+гЂђ # гЂ‘
Press alarm panel query key of your keyboard, then
blinking status LED on and then press 9901#, press 8 to
scroll up and 0 to scroll down for records. Other
indications as:
JP = arm/disarm from keyboard
YC = arm/disarm from remote
tP = interference alert
01 = remote control number 1
Query alarm panel The system can save up to the most recent 102 alarming
alarming records
records.
Press alarm panel query key of your keyboard, then
Syntax:
blinking status LED on and then press 9900#, press 8 to
9900+гЂђ # гЂ‘
scroll up and 0 to scroll down for records.
Example: Screen shows 01-01 22-02 02 alarm, which
means alarm happened on 1st January 22:02pm at zone 2.
5
Types of Alarm Zone
5.1 Definitions of Zones
The alarm supports 99 distinguishable defense zones and they can be classified into one
of the 8 Zone Types with their respective characteristics.
Type Zone Type
ID
1
NORMAL Defense
Zone
2
STAY Defense zone
(AT-HOME Defense
zone)
3
INTELLIGENT
Defense zone:
4
EMERGENCY
Defense zone:
5
CLOSED Defense
zone:
Interpretation
The Panel only works on the arming status. When
disarming, there is no response.
Can be shut off solely through the remote control
(Keypad) to avoid the Infrared Detectors and other
in-room detectors from misinformation when master is
resting at home.
If the detector in the Defense zone is triggered only
once, it will not immediately alarm. But if being
triggered once again within 30 seconds after the first
triggering, it will not alarm immediately.
No matter on arming or disarming status, if detector is
triggered it will alert. Usually used in connecting with
Smoke Detectors, Gas Detectors and emergency
button, etc.
No matter arming or disarming status, detectors will
not alert even being triggered.
6
CHIME Zone
No matter in what status, when sensor with this zone is
triggered, a welcome door bell will be ring as
notification.
7
WELCOME Zone
On disarming status, when sensor with this zone is
triggered, a welcome voice message will be played.
8
HELP SENIOR
Defense Zone
This type of zone is for elderly safety, no matter in
what status, the panel will alarm once sensor with this
zone type is triggered.
5.2 System default zone types are:
Normal
Stay
Intelligent
01-59
60-79
80-89
Help
Senior
90
Chime
Welcome
Emergency
91
92
93-99
5.3 Fitting parameters:
-
-
Input voltage: DC9V-12V
Standby currents: < 25mA
Alarm current: пјњ 450 mA
пЃ® Wireless frequency: 433MHZ
пјЊ2262/1.5-4.7M пјЊ EV1527/300K
пЃ® Backup battery: NI-HI AAA*6 DC7.24V
пЃ® Alarm loudness: 110dB
Detailed parameters: The alarm should be compatible with PT2262, PT2240 and
EV1527. Using PT2262 encoding, the resistance is recommended 1.5M-4.7M;
using with EV1527 encoding, the resistance by 180K-470K. It is advised to place
jumpers randomly at A0-A7 for addressing of individual sensor, better not to let
them totally empty for security.
6
Guideline of Installation Sensors
6. 1
Guideline for Installing Door or Window Sensor
1. The surface for door sensor installation should be clean so door sensor can be
attached to the door and frame firmly with double faced adhesive.
2. Each door sensor is a pair of sensor and magnet. The sensor (A as in diagram)
should be installed on the fixed door frame and the magnet (B as in diagram) should
be placed on the movable door with a distance not exceeding 1 cm.
3. Upon installed, door sensor should be tested by open the door and check if the
indicator on door sensor flashes for 1 second.
4. In case the door sensor is running out of battery, the indicator should be kept lit as a
low-voltage notification.
6.2 Guideline for Installing PIR Motion Sensor
1. Before use, make sure the power switch of PIR motion sensors is at the ON
position.
2. Installation height is about 2.2 meters above ground and the optimized detection
angle for most motion sensor is 90 degree. The sensor should face the detected area
with this consideration for best coverage. It is advised to install with the face of
motion sensor perpendicular to the most probable moving detection of people for
the highest effective detection.
3. Within coverage of detection, there should be no any objects for obstruction.
4. There should be no two infrared detectors in the same as they will possibly
intervene with each other.
5. Avoid the detector facing window, cooling or warming machines, or other
appliances that cause the temperature changing sharply and thus cause false alarm.
6. Most infra-red detector needs about 5 minutes to heat up before READY for normal
operation.
7. Regular PIR motion sensor is for indoor use unless the specification stated
otherwise.
Unless specifies otherwise, most infra-red detector are indoor use and not reliable to
use outdoor.
7. Troubleshooting
Problem
1. cannot dial for
alarm
2. cannot
long-distance
operation
3. no record
indication when
alerting
4. remote control
(keyboard) out of
order
5. infrared detector
out of order
6. Beam detector
out of order
Diagnosis
п‚· no arming
п‚· alerting phone unsettled
п‚· parts improperly installed
e.g. sensors installed too far
away
п‚· code no match
п‚· password input wrongly
Available Solutions
п‚· do arming operation
п‚· re-set according to the
specification
п‚· coordinating the location of parts
п‚· re-coding
п‚· voice message not recorded
п‚· record voice message
п‚· coding un-matched with the
Panel
п‚· insufficient battery power or
battery contact no good
п‚· battery pieces poor contact
or voltage un-matched with
Panel
п‚· low power
п‚· re-learn the remote control
п‚· change battery to correct type
п‚· polish the surface of contact of
battery
п‚· contact the local dealer to change
the matched remote control
(keyfob)
п‚· change to the same type battery
п‚· Retype Password or reset password
п‚· Check power supply
п‚· Replaced with a working power
adapter
п‚· Check if cables short circuit.
п‚· Check beam detector
п‚· Re-cabling for perfect contact
alignment
п‚· Make sure pair of sensors aligned
by observing the indicators.
7. siren without
sound
8. the transmission
distance of detector
to panel shorten
9. Alarm triggered
continuously right
after power up
п‚· siren plug or jack in short
circuit or broken-line
п‚· siren out of order
п‚· closed siren by command
п‚· positive and ground wires of
siren reversed
п‚· a nearby emitter is sending
code
п‚· Panel receiver stoppage
п‚· standby battery of the Panel
insufficient
п‚· repair or change plug or jack or
change the jack line
п‚· use another siren to double check
п‚· activate siren by command
п‚· reverse the wires to try adjust a
longer length of siren sounding
п‚· move one detector next to panel
and try
п‚· identify the interfering source and
eliminate it
п‚· check Panel power whether
plugged well
п‚· Phone cord is not connected п‚· Either disable the phone alert
but the phone alert function
function or connect the phone
is enabled
cord
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement