Installation Manual

Installation Manual
PowerLogic™ Power Meter 700
Installation Guide
English
63230-501-204A1
07/2008
Additional Resources
INSTALLATION
Dimensions
Go to www.powerlogic.com, select your country > literature > Power Meters > PM700 > Instructional, and
then click the manual you want to download. If you do not have a user name and password, follow the
instructions on the web site.
Box Contents
Figure 2: PM700 Dimensions
SAFETY PRECAUTIONS
•
•
•
One (1) power meter
Two (2) retainer clips
One (1) installation sheet
+0.8
92 –0.0
(3.62)
Parts of the PM700
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
• Apply appropriate personal protective equipment (PPE) and follow safe electrical work
practices. In the USA, see NFPA 70E.
• Only qualified electrical workers should install this equipment. Such work should be
performed only after reading this entire set of instructions.
• NEVER work alone.
• Before performing visual inspections, tests, or maintenance on this equipment, disconnect
all sources of electric power. Assume that all circuits are live until they have been completely
de-energized, tested, and tagged. Pay particular attention to the design of the power system.
Consider all sources of power, including the possibility of backfeeding.
• Turn off all power supplying the power meter and the equipment in which it is installed before
working on it.
• Always use a properly rated voltage sensing device to confirm that all power is off.
• Before closing all covers and doors, carefully inspect the work area for tools and objects that
may have been left inside the equipment.
• Use caution while removing or installing panels so that they do not extend into the energized
bus; avoid handling the panels, which could cause personal injury.
• The successful operation of this equipment depends upon proper handling, installation, and
operation. Neglecting fundamental installation requirements may lead to personal injury as
well as damage to electrical equipment or other property.
• NEVER bypass external fusing.
• NEVER short the secondary of a PT.
• NEVER open circuit a CT; use the shorting block to short circuit the leads of the CT before
removing the connection from the power meter.
• Before performing Dielectric (Hi-Pot) or Megger testing on any equipment in which the power
meter is installed, disconnect all input and output wires to the power meter. High voltage
testing may damage electronic components contained in the power meter.
• The power meter should be installed in a suitable electrical enclosure.
Figure 1: PM700
• ➀ Control Power.
• ➁ Voltage Inputs.
• ➂ Current Inputs.
• ➃ Not used.
• ⑤ LED.
–Regular flashing =
functioning system.
–Irregular flashing =
communications indicator.
–Steady OFF/ON = meter not
functioning.
➀
➁
+0.8
92 –0.0
(3.62)
B
96
A
Mounting
(3.78)
50
1. Insert the power meter
through the 92 mm x 92 mm
(3.62 in. x 3.62 in.) cut-out
(see Figure 2).
2. Attach the two retainer clips to
the power meter using the
retainer slots at position A or
position B (shown in drawing
on right).
There are two sets of retainer
slots on the left, right, top and
bottom of the power meter. The
first set is for installation
locations thinner than 3 mm
(1/8 in.). The second set is for
installation locations 3 to 6 mm
(1/8 in. to 1/4 in.).
(1.97)
A
19
96
(3.78)
WIRING
B
Voltage inputs and control power for distribution systems up to 277 V L-N and 480 V L-L complies with
metering category III. Also, terminal wiring should have a minimum temperature rating of 80° C.
Polarity marks must be followed as shown for CTs (S1=X1, S2=X2) and PTs ( ■ = X1). See Tables 1 and
4 for connector specifications and wiring symbols.
➂
➃
⑤
NOTE: For use on a flat surface of a
protective enclosure (for example, in
the USA: NEMA 1 rated enclosure or
better).
Failure to follow this instruction will result in death or serious injury
(0.75)
mm (in.)
Table 1:
Connector Specifications for PM700.
Connection
Number
Wire Dimensions
1 and 2
12 to 24 AWG
2.5 to 0.2 mm2
Voltage Inputs
(PTs)
3, 4, 5, and 6
12 to 24 AWG
2.5 to 0.2 mm2
12 to 24 AWG
2
Current Inputs
(CTs)
14, 15, 16, 17, 18,
and 19
Insulation
Strip Length
Torque
Power Supply
2.5 to 0.2 mm
.
4 in.lb
4 in lb
.
3.54 to
4.43 in lb
.
0.45 N.m
0.45 N m
.
0.4 to 0.5 N m
1/4 in
6.0 mm
1/4 in
6.0 mm
1/4 in
6.0 mm
NOTE: Connections 7, 8, 9, and 10 are not used.
NOTE: Connections 11, 12, and 13 are not present on the power meter.
Table 3:
Table 2:
Number of
Wires
Number of
Wires
Voltages Less Than or Equal to 277 Vac L-N/480 Vac L-L, Direct Connect No PTs
CTs
Qty.
Voltage Connections
ID
Qty.
ID
3
CTs
System
Type
PT Primary
Scale
Figure Number
I1
2
V1, Vn
L-N
10
No PT
3
1
I1
2
V1, V2
L-L
11
No PT
4
2
I1, I2
3
V1, V2, Vn
L-L with N
12
No PT
5
4
ID
Type
System
Type
PT Primary
Scale
3
I1, I2, I3
3
V1, V2, V3, (Vn
to Ground)
Grounded
Wye
40
Based on
voltage
2
V1, V3 (Vn to
Ground)
Wye
42
Based on
voltage
14
3
V1, V2, V3 (Vn
to Ground)
Grounded
Wye
40
Based on
voltage
15
I1, I2, I3
2
I1, I2, I3
I1
3
V1, V2, V3 (Vn
to Ground)
Three-Phase Wiring
3
4
Table 3:
2
I1, I3
3
V1, V2, V3
Delta
30
No PT
6
3
I1, I2, I3
3
V1, V2, V3
Delta
31
No PT
7
1
I1
3
V1, V2, V3
Delta
(Balanced)
32
No PT
3
I1, I2, I3
3
V1, V2, V3, Vn
4-wire
Delta
40
No PT
3
I1, I2, I3
3
V1, V2, V3, Vn
Wye
40
No PT
1
I1
3
V1, V2, V3, Vn
Wye
(Balanced)
44
No PT
Figure
Number
Qty.
1
* Single-phase systems must be connected only as shown in wiring diagrams. Otherwise, meter will not display values.
Meter Configuration
ID
3
1
Voltage Connections
Qty.
Meter Configuration
Type
Single-Phase Wiring*
2
Wiring Diagrams
Voltages Greater Than 277 Vac L-N/480 Vac L-L
Three-Phase Wiring
Supported System Types
Grounded
Wye
(Balanced)
44
14
15
16
17
18
19
S2
•
•
Symbol
V
V
V
V
3
4
5
6
16
Wiring Diagram Symbols
Description
8
1
2
3
N
20
Fuse
3
4
VL-L <= 480V
5
6
Use System type 10.
To avoid distortion, use parallel wires for control
power and voltage inputs. Keep the fuse close
to the power source.
Earth ground
14
15
16
17
18
19
S2
•
•
•
Figure 5: 1-Phase Direct Voltage
Connection 2 CT
V1
V2
V3
VN
N
S1
S1
I1+
I1–
I2+
I2–
I3+
I3–
Voltage disconnect switch
Voltages Greater Than 277 Vac L-N/480 Vac L-L
L3
13
19
8
L1 L2
S2
I1+
I1–
I2+
I2–
I3+
I3–
Use System type 11.
To avoid distortion, use parallel wires for control
power and voltage inputs. Keep the fuse close
to the power source.
Use with 120/240 V systems.
L1 L2
S1
S2
3
3
CTs
Voltage Connections
Meter Configuration
Qty.
ID
Qty.
ID
Type
2
I1, I3
2
V1, V3 (V2 to
Ground)
Delta
30
Based on
voltage
9
3
I1, I2, I3
2
V1, V3 (V2 to
Ground)
Delta
31
Based on
voltage
10
V1, V3 (V2 to
Ground
Delta
(Balanced)
1
I1
2
3
I1, I2, I3
3
V1, V2, V3, (Vn
Wye
to Ground)
(Unbalanced)
3
V1, V2, V3, (Vn
Wye
to Ground)
(Unbalanced)
3
V1, V2, V3, (Vn
Wye
to Ground)
(Unbalanced)
2
1
I1, I3
I1
PT Primary
Scale
Current transformer.
Polarity marks: S1=X1, S2=X2.
S1 (X1)
Figure
Number
System
Type
S2 (X2)
Shorting block
3
4
5
6
V1
V2
V3
VN
14
15
16
17
18
19
I1+
I1–
I2+
I2–
I3+
I3–
S1
32
Based on
voltage
18
40
Based on
voltage
11
40
Based on
voltage
12
44
Based on
voltage
17
S2
Potential transformer.
Polarity marks: ■ = X1.
S1
S2
Protection containing a voltage disconnect switch with a fuse or
disconnect circuit breaker (the protection device must be rated for
the available short-circuit current at the connection point).
L1
V1
L1
V2
L2
L3
V3
L2
L3
In 2 PT systems, these connections are equivalent.
Polarity marks: ■ = X1.
V1
•
V2
V3
S1
Use System type 12.
To avoid distortion, use parallel wires for control
power and voltage inputs. Keep the fuse close
to the power source.
•
Use System type 30.
V1
V2
V3
VN
14
15
16
17
18
19
I1+
I1–
I2+
I2–
I3+
I3–
S1
S2
S2
•
•
V1
V2
V3
VN
14
15
16
17
18
19
I1+
I1–
I2+
I2–
I3+
I3–
S1
S2
S1
14
15
16
17
18
19
I1+
I1–
I2+
I2–
I3+
I3–
Use System type 40.
Use with 480Y/277 V and 208Y/120 V systems.
L1 L2 L3
■
■
■
■
3
4
5
6
V1
V2
V3
VN
14
15
16
17
18
19
I1+
I1–
I2+
I2–
I3+
I3–
S1
S2
For an open delta PT connection with 120 V L-L
secondaries, use System type 30.
S1
S2
S1
■
■
■
■
3
4
5
6
V1
V2
V3
VN
14
15
16
17
18
19
I1+
I1–
I2+
I2–
I3+
I3–
S2
S2
•
S1
V1
V2
V3
VN
Figure 10: 3-Phase 3-Wire Delta
Connection 3CT 2PT
L1 L2 L3
3
4
5
6
S1
3
4
5
6
S2
Figure 9: 3-Phase 3-Wire Delta Connection
2 CT 2 PT
S1
S2
3
4
5
6
Use System type 31.
L3
S2
•
•
L1 L2 L3
S2
Figure 6: 3-Phase 3-Wire 2 CT no PT
N L1 L2
S1
Three-Phase Wiring
Number of
Wires
Figure 8: 3-Phase 4-Wire Wye Direct
Voltage Input Connection 3 CT
L1 L2
The following symbols are used in the wiring diagrams:
Table 4:
Figure 4: 1-Phase Line-to-Line 2-Wire
System 1 CT
N L1
S1
Based on
voltage
Figure 7: 3-Phase 3-Wire 3 CT no PT
Figure 3: 1-Phase Line-to-Neutral 2-Wire
System 1 CT
•
•
Use System type 31.
For an open delta PT connection with 120 V L-L
secondaries, use System type 31.
Figure 11: 3-Phase 3-Wire Wye Connection
3 CT 3 PT (unbalanced)
Figure 12: 3-Phase 3-Wire Wye Connection
2CT 3PT (unbalanced)
L1 L2 L3
L1 L2 L3
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
3
4
5
6
14
15
16
17
18
19
S1
V1
V2
V3
VN
S1
I1+
I1–
I2+
I2–
I3+
I3–
S1
•
N
■
■
■
■
■
S1
S1
3
4
5
6
V1
V2
V3
VN
14
15
16
17
18
19
I1+
I1–
I2+
I2–
I3+
I3–
Use System type 40.
•
■
■
■
S1
S2
•
I1+
I1–
I2+
I2–
I3+
I3–
S2
•
Use System type 40.
Figure 17: 3-Phase 3-Wire Wye 1CT 3PT
(unbalanced)
3
4
5
6
V1
V2
V3
VN
14
15
16
17
18
19
I1+
I1–
I2+
I2–
I3+
I3–
S1
3
4
5
6
V1
V2
V3
VN
14
15
16
17
18
19
I1+
I1–
I2+
I2–
I3+
I3–
■
■
■
■
■
S1
S2
3
4
5
6
V1
V2
V3
VN
14
15
16
17
18
19
I1+
I1–
I2+
I2–
I3+
I3–
N
S2
Use System type 44
•
Figure 18: 3-Phase 3-Wire 1 CT 2 PT
(balanced)
•
■
■
■
■
14
15
16
17
18
19
I1+
I1–
I2+
I2–
I3+
I3–
3
4
5
6
V1
V2
V3
VN
14
15
16
17
18
19
I1+
I1–
I2+
I2–
I3+
I3–
Figure 24: Control Power Transformer
(CPT) Connection
N L1 L2 L3
L1 L2 L3
S1
S2
•
Use System type 32
Figure 23: Direct Connect Control Power
(DC Control Power)
3
4
5
6
V1
V2
V3
VN
14
15
16
17
18
19
I1+
I1–
I2+
I2–
I3+
I3–
1 2
1 2
- +
- +
•
•
DC Control Power 100 Vdc < V < 300 Vdc
See Table 5.
•
•
Control Power Transformer
120 or 240 Vac Secondary 50 Va max.
See Table 5.
Use System type 44
Figure 22: Direct Connect Control Power
(Phase to Neutral)
N L1 L2 L3
1 2
1 2
-+
- +
Table 5:
Fuse Recommendation
Control Power Source
Source Voltage (Vs)
Fuse
Fuse Amperage
CPT
Vs ≤125 V
FNM or MDL
250 mA
CPT
125 < Vs ≤240 V
240 < Vs ≤305 V
FNQ or FNQ-R
250 mA
CPT
FNQ or FNQ-R
250 mA
Line Voltage
Vs ≤240 V
FNQ-R
250 mA
Line Voltage
Vs > 240 V
Vs ≤300 V
FNQ-R
250 mA
LP-CC
500 mA
DC
NOTES:
S2
•
V1
V2
V3
VN
L1 L2 L3
S1
Use System type 44
3
4
5
6
Figure 21: Direct Connect Control Power
(Phase to Phase)
•
•
•
•
Use System type 42.
Figure 20: 3-Phase 4-Wire Direct Voltage
Input Connection 1 CT
(balanced)
L3
S1
L1 L2 L3
■
S2
Use System type 40.
S1
L1 L2 L3
■
S1
S2
•
S1
L1 L2 L3
S2
14
15
16
17
18
19
S2
V1
V2
V3
VN
L1 L2
S2
■
S1
S2
I1+
I1–
I2+
I2–
I3+
I3–
Figure 14: 3-Phase 4-Wire Wye 3CT 2PT
(balanced)
L1 L2 L3
3
4
5
6
S1
S2
Use System type 40.
S2
14
15
16
17
18
19
S2
Figure 13: 3-Phase 4-Wire Wye Connection
3 CT 3 PT
N
V1
V2
V3
VN
3
4
5
6
Figure 19: 3-Phase 3-Wire Direct Voltage
Input Connection 1 CT
(balanced)
L1 L2 L3
■
S2
•
N
L1 L2 L3
■
S1
S2
N
Figure 16: 3-Phase 4-Wire Wye 1 CT 3PT
(balanced)
■
S1
S2
Figure 15: 3-Phase 4-Wire Wye 2 CT 3 PT
(for balanced 3-wire loads)
•
Use System type 32
Phase to Phase only when voltage
< 415 + 10% Vac max.
See Table 5.
•
•
Phase to Neutral only when voltage
< 300 + 10% Vac max.
See Table 5.
See Figure 21 to Figure 24.
Over current protection should be located as close to the device as possible.
For selecting fuses and circuit breakers other than those listed above, use the following criteria:
• Over current protection should be rated as listed above.
• Current interrupt capacity should be selected based on the installation category and fault current capability.
• Over current protection should be selected with a time delay.
• The voltage rating should be based on the input voltage applied.
• If a 0.25 A fuse is not available with the required fault current capability, use a fuse rated at a maximum of
0.5 A.
OPERATING THE DISPLAY
The power meter is equipped with a large, back-lit LCD display. It can display up to five lines of information
plus a sixth row of menu options. Figure 25 shows the different parts of the power meter display.
Figure 26: PM700 Abbreviated IEC Menu Hierarchy*
Figure 25: Parts of PM700 Display
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
M.
Type of measurement
Screen Title
Alarm icon
Maintenance icon
Bar Chart (%)
Units
Display more menu items
Menu item
Selected menu indicator
Button
Return to previous menu
Values
Phase
A
B
C
PHASE
DMD
U-V
U
V
PQS
PQS
I
)
L
ZZZZZ\\\\\\
!
E
F
ZZZZZ\\\\\\
!
0(!3%
PHASE
DMD
ZZZZZ\\\\\\
!
!
.
1. Press ###: until you see SETUP.
2. Press SETUP.
3. Enter your password. The default
password is 00000.
4. Press OK.
5. Press METER.
6. Press CT.
7. Enter the PRIM CT (primary CT) number:
1 to 32762.
8. Press OK.
9. Enter the SEC. CT (secondary CT)
number: 1 or 5.
10. Press OK.
11. Press 1; to return to the SETUP MODE
screen.
PEAK
-!8$%-!.$
M
Setup Example: This example shows how to set up CTs. Use the same method to set up PTs and
Communication.
D
E
$-$
Ph
Qh
Sh
PF
G
#42!4)/
#4
#4
02)3%#
/+
F
K
J
I
H
How the Buttons Work
Table 6:
MINMX
Navigation
--->
U
V
See the online PM700 Reference Guide at www.powerlogic.com for more information on setting up the
power meter.
I
1;
Return to the previous menu level.
^
Indicates the menu item is selected and there are no menu levels below the current level.
+
I
V
PQS
PF
F
THD V
THD I
Getting Technical Support
Please refer to the Technical Support Contacts provided in the power meter shipping carton or go to
www.powerlogic.com, select your country > tech support for support phone numbers by country.
TIMER
RESET
METER
SETUP
METER
DIAGN.
METER
E
DMD
MINMX
MODE
TIMER
Change values or scroll through the available options. When the end of a range is reached,
pressing + again returns to the first value or option.
<-
Select the next number of a series.
OK
Move to the next editable field or exits the screen if the last editable field is selected.
Set Up the Power Meter
Figure 26 shows abbreviated hierarchical relationships of the menu screens for the PM700. Using the
Setup Example below in conjunction with the menu hierarchy (Figure 26), complete a minimum setup of
the power meter. A minimum setup includes:
Set up CTs.
Set up PTs.
MINMX
View more menu items on the current level.
Change Values
•
•
THD
Button Symbols
DMD
PASSW
BARG
U = Voltage, L-L
V = Voltage, L-N
Schneider Electric
Power Monitoring and Control
*The power meter can be configured to display either IEC or IEEE nomenclature. Figure 26 shows IEC
nomenclature.
295 Tech Park Drive, Suite 100
This product must be installed, connected, and used in compliance with prevailing
standards and/or installation regulations. As standards, specifications, and designs
change from time to time, please ask for confirmation of the information given in
this publication.
LaVergne, TN 37086 USA
Tel: +1 (615) 287-3400
63230-501-204A1
www.powerlogic.com
© 2008 Schneider Electric. All Rights Reserved.
07/2008
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement