heated bedding
Includes
QUICK
SET-UP
GUIDE
pages 4-5
heated bedding
U S E R
M A N U A L
TRUSTED FOR OVER
100 YEARS
P.N. 174822
IMPORTANT INSTRUCTIONS
DO NOT DESTROY
WARNINGS AND SAFEGUARDS
AS WITH ALL ELECTRICAL PRODUCTS, MISUSE OF PRODUCT OR FAILURE TO
PROPERLY FOLLOW THE INSTRUCTIONS MAY CAUSE OVERHEATING, FIRE OR
PERSONAL INJURY. PLEASE READ THE PRODUCT LABEL AND ALL OF THE
INSTRUCTIONS BEFORE USING YOUR HEATED PRODUCT.
1. DO NOT USE THIS HEATED PRODUCT WITH AN INFANT, A CHILD, AN
INCAPACITATED OR IMMOBILE PERSON, A PARAPLEGIC, A QUADRIPLEGIC,
A DIABETIC, ONE INSENSITIVE TO HEAT SUCH AS A PERSON WITH
POOR BLOOD CIRCULATION, OR ANYONE WHO CANNOT CLEARLY
UNDERSTAND THE INSTRUCTIONS AND/OR OPERATE THE CONTROLS.
2. DO NOT USE BLANKET/MATTRESS PAD ON A WATERBED, SOFA, BUNK
BED OR MECHANICALLY ADJUSTABLE BED AND DO NOT USE THROW
ON A WATERBED, BUNK BED OR MECHANICALLY ADJUSTABLE BED.
3. FOR THROW BLANKETS: DO NOT USE WITH ROCKING
CHAIRS, RECLINERS, CHAIRS WITH CASTERS OR WHEELS,
OR OTHER FURNITURE SUBJECT TO MOVEMENT.
4. DO NOT USE WITH ANOTHER ELECTRICALLY HEATED PRODUCT
SUCH AS A BLANKET, MATTRESS PAD OR THROW.
5. DO NOT ROUTE ELECTRICAL CORDS BETWEEN THE MATTRESS
AND BOX SPRING. DO NOT ALLOW THE CORDS TO BE PINCHED.
6. DO NOT USE WITH DAMAGED CORDS. DAMAGED CORDS
CAN LEAD TO POSSIBLE OVERHEATING OR FIRE.
7. WRAPPING THE CORD AROUND THE CONTROLLER MAY
DAMAGE THE CORD. LOOP LOOSELY WHEN STORING.
8. DO NOT DRY CLEAN THIS HEATED PRODUCT. CLEANING
LIQUID MAY DAMAGE THE INSULATION OF THE HEATING
ELEMENT. IMPROPER LAUNDERING MAY CAUSE PROBLEMS
WITH THE HEATING WIRE WHICH CAN LEAD TO FIRE.
9. DO NOT TUCK IN, PINCH, FLEX OR EXPOSE THE HEATING WIRE. DO NOT
WRAP OR TUCK THE HEATED PRODUCT, SUPPLY CORD OR CONTROL
IN A SOFA OR OTHER FURNITURE. ALL PORTIONS OF THE HEATED
PRODUCT AND CONTROLLERS SHOULD BE VISIBLE AT ALL TIMES.
10. TURN OFF OR UNPLUG THE CONTROL FOR THE
HEATED PRODUCT WHEN NOT USING.
2
For questions or support, please visit www.sunbeam.com.
11. CONTROLLER IS NOT WATERPROOF. DO NOT IMMERSE IN WATER.
12. KEEP THE CONTROL AWAY FROM DRAFTY AREAS THAT MAY
BECOME DAMP OR WET SUCH AS AN OPEN WINDOW.
13. DO NOT USE PINS; THEY MAY DAMAGE THE ELECTRIC WIRING.
14. BE SURE THIS BLANKET/MATTRESS PAD/THROW IS USED
ONLY ON AN AC SUPPLY CURRENT CIRCUIT OF 110-120 VOLTS
60 HZ. DO NOT USE WITH AN EXTENSION CORD. DO NOT USE
WITH GENERATORS, POWER CONVERTERS, OR INVERTERS.
15. THE PRODUCT MAY EXPERIENCE INCREASED HEAT IN AREAS WHERE
HEATED PRODUCT IS BUNCHED OR FOLDED WHILE IN USE.
16. KEEP ALL DOGS, CATS AND OTHER PETS AWAY FROM THIS
HEATED PRODUCT. THIS IS AN ELECTRICAL APPLIANCE
THAT THEY CAN DAMAGE OR BE INJURED BY.
17. USE THE PROPER SIZE BLANKET/MATTRESS PAD FOR YOUR BED. FOR
EXAMPLE, USE A TWIN SIZE WARMING BLANKET ON A TWIN SIZE BED.
18. NOT FOR HOTEL, MOTEL OR OTHER INSTITUTIONAL USE.
19. IF IMPROPER OPERATION OF THIS PRODUCT IS OBSERVED, UNPLUG
IMMEDIATELY, DISCONTINUE USE AND CALL SUNBEAM CONSUMER
CARE IN THE U.S AT 800-892-7684 OR IN CANADA AT 800-667-8623.
20. CHECK WITH YOUR HEALTHCARE PROVIDER BEFORE USING
WITH A PACEMAKER OR ANY MEDICAL DEVICES.
21. THROW CONTROLLERS MUST NOT BE WRAPPED,
COVERED OR TUCKED WHEN OPERATING.
SAVE THESE INSTRUCTIONS; DO NOT DESTROY
POLARIZED PLUG:
IMPORTANT
Plug power cord into a 110-120 volt wall outlet. Do not attempt to
force the plug. This appliance has a polarized plug (one blade is
wider than the other). To reduce the risk of electrical shock, this plug
is intended to fit only one way into an outlet. If the plug does not fit
in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician.
Do not attempt to defeat this safety feature
IF THE FOLLOWING IMPORTANT INSTRUCTIONS ARE NOT
FOLLOWED, THE HEATED PRODUCT WILL NOT OPERATE PROPERLY.
For questions or support, please visit www.sunbeam.com.
3
QUICK SET-UP GUIDE
Mattress Pad & Blanket
STEP 4
TWIN/FULL
SINGLE CONTROL SET-UP
STEP
1
Place on bed with
label at foot of bed
facing out
Plug Power Cord
into wall
Power Cord
Left Side
Control
Right Side
STEP
2
Connect the Control
Cord connector and
module securely
Module
Label
Control Cord
Connector
STEP 3 Run Control Cord
under the bed
Flag Tag
BASE UNIT FOR
REMOTE CONTROL
SET-UP
4
1
Module
2
3
Run Base Unit Cord under the bed
QUEEN/KING/CALIFORNIA KING
DUAL CONTROL SET-UP
STEP
STEP
1
2
Place on bed with
label at foot of bed
facing out
STEP 4
Plug Power Cord
into wall
Left (Secondary)
Control
Connect the Control
Cord connector and
module securely
Power Cord
Left Side
Right Side
(Label on back
of control)
Module
Label
Control Cord
Connector
Flag Tag
STEP 3 Run Control Cord
under the bed
4
Right
(Primary) Control
For questions or support, please visit www.sunbeam.com.
QUICK SET-UP GUIDE
Heated Throw
STEP
STEP
1
2
Flag Tag
Connect the Control
Cord connector and
module securely
Control
Plug Power Cord
into wall
Power
Cord
Module
Flag Tag
Throw Cord
Connector
Label
Throw Cord
Control
Control Cord
Control Cord
Connector
Connector
Power
Cord
Module
Throw Cord
Connector
Label
Throw Cord
PLEASE follow these directions in the order they are given to
ensure your product will work correctly. Do not turn on the
product until it has been fully assembled.
CAUTION:
• Always make sure cords and controls are NOT trapped or
pinched between bed slats, mattress, springs, against wall,
foot board or bed frame, or between furniture, walls or chairs.
• Do not plug main power cord into the wall
IMPORTANT
outlet until you have completely set up your
heated product per the instructions.
For questions or support, please visit www.sunbeam.com.
5
Table of Contents
Quick Set-Up Guide................................................................................................. 4-5
Heated Blanket, Mattress Pad and Comforter
Setup...................................................................................................................... 7
Controllers........................................................................................................ 8-10
Heated Throw
Setup.................................................................................................................... 11
Control Features................................................................................................... 11
Care and Cleaning.................................................................................................... 12
Frequently Asked Questions................................................................................ 13-14
Warranty............................................................................................................. 15-16
How to Obtain Warranty Service................................................................................ 16
DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE.
If you have any questions while setting up or using your product,
please visit us on the World Wide Web at: www.sunbeam.com or
contact Sunbeam Consumer Care in the U.S. at (800) 892-7684
or in Canada at (800) 667-8623.
CAUTION: Do not plug main power cord into the wall outlet until you have
completely set up your heated product per the instructions.
• Disconnect power cord from wall before detaching control from heated product.
• Always make sure cords and controls are NOT trapped or pinched between bed slats,
mattress, springs, against wall, foot board or bed frame, or between furniture, walls or chairs.
CAUTION: Do not attempt to force the plug. This appliance has a polarized plug
(one blade is wider than the other). To reduce the risk of electrical shock, this plug
is intended to fit only one way into an outlet. If the plug does not fit in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
IMPORTANT
6
For questions or support, please visit www.sunbeam.com.
Heated Blanket, Mattress Pad and
Comforter Setup
1 Place the heated blanket/mattress pad on the bed with the label at the foot of the bed facing upward.
2Connect the cord into the module at the bottom of the heated blanket/ mattress pad until the plastic
hinges click into place.
CAUTION: Cord must be COMPLETELY CONNECTED. A risk of fire could result from a loose connection.
3Run the control cord on the floor under the bed. Do not sandwich cord between the mattress and box
spring. Avoid any tangling or pinching.
4 Plug power cord into a 110-120 volt wall outlet.
CAUTION: Do not use with generator power.
Control Placement:
•D
ual Control for heated blanket or mattress pad – place primary control (label on back of
control) on the right side of the bed.
STEP 4
STEP
STEP
1
2
Place on bed with
label at foot of bed
facing out
Plug Power Cord
into wall
Left (Secondary)
Control
Connect the Control
Cord connector and
module securely
Power Cord
Left Side
Right
(Primary) Control
Right Side
(Label on back
of control)
Module
Label
Control Cord
Connector
Flag Tag
STEP 3 Run Control Cord
under the bed
•S
ingle Control for heated blanket or mattress pad –
the control can be placed on either side of the bed.
STEP 4
Plug Power Cord
into wall
Power Cord
STEP
1
Place on bed with
label at foot of bed
facing out
Left Side
Control
Right Side
STEP
2
Connect the Control
Cord connector and
module securely
Module
Label
Control Cord
Connector
Flag Tag
See Control Features on page 8
for your individual control.
STEP 3 Run Control Cord
under the bed
If there is a flashing light or your control displays
a flashing “F” ,“FF”, “F1” or “F2” see page 8.
For questions or support, please visit www.sunbeam.com.
7
Control Chart
OneSet™
SimpliTouch™ EasySet™ Pro StyleSmart™ II ComfortSet™ SelectTouch™ ChoicePlus™ DesignSmart™ ChoiceTouch™ EliteStyle™ PrimeStyle™ EliteStyle™ II
SimpliTouch™ Pro
AO
Style #
(Single
Control)
Y85
K85P
S85/S85A U85/U85A 085
P85/
P85A
85P
W85/
W85A
X85/X85A
Style #
(Dual
Control)
Y85KQ
K85KQP
S85KQ/
S85KQA
P85KQ/
P85KQA
85KQP
W85KQ/
W85KQA
X85KQ/
X85KQA
U85KQ/
U85KQA
Backlit
Display
085KQ
b
LED
Display
Warming
Settings
b
b
b
b
b
10 hour
10 hour
10 hour*
(S85A,
S85KQA)*
10 hour
10 hour
Select
10 hour
Selectable
A/0
2, 6 or 10
hour
Selectable
A/0
2, 6 or 10
hour
3 hour
3 hour
3 hour
5
10
10
10
10
20
20
10
10
3
3
3
b
b
b
b
b
Programable
b
b
b
Preheat
Easy Grip
b
b
Ambient
Temperature
Compensation
Auto-Off
b
N85AP M85AP T85A
Throw Throw Throw
b
b
b
b
* S85KQA only
If your controller does not appear on the chart, please visit our website for more information.
Control Features
(for all controllers except DesignSmart™ and ChoiceTouch™, see page 9 for
detailed features.)
Auto-Off Feature:
The “Auto-Off” feature is designed for conservation of energy by automatically turning your blanket or
mattress pad off after 10 hours of continuous use (3 hours for throws).
For Dual Controls:
Each control operates independently and will turn off 10 hours after the control is turned “On”.
Auto-Off Select* Feature (selected models only):
Some models with the “Auto-Off” feature (see control chart) offer an “Auto-Off Select” button that can
disable the “Auto-Off” feature so the heated product will not automatically turn off.
Controls with the “Auto-Off Select” feature have the “Auto-Off” active as the default so the heated product
will automatically turn off after 10 hours.
To disable the “Auto-Off”, press the “Auto-Off Select” button. The word “StayOn” will appear in the digital
display to indicate the “Auto-Off” feature is deactivated and the heated product will NOT automatically turn
off after 10 hours. The heated product will remain on until the product is manually turned off by pressing the
“On/Off” button.
To activate auto-off, press the “Auto-Off Select” button. The word “AutoOff” will appear in the digital display to
indicate the “Auto-Off” feature is activated and the heated product will automatically turn off after 10 hours.
Note: After a power outage, the “Auto-Off” feature automatically resets the timer.
To restart all heated products after a power failure:
Press the power button and the heated product will begin to warm.
8
For questions or support, please visit www.sunbeam.com.
Preheat Feature (selected models only):
The preheat function will heat the bed for a period of 30 minutes and the control will return to its original setting.
1 To use the preheat feature, simply turn on the warming product by pressing the “On/Off” button and then
press the “Preheat” button. The display will show “PH” while the function is activated.
2 To reset the preheat feature, simply turn off the control by pressing the “On/Off” button and then turn it
back on by pressing the “On/Off” button.
Using Your Control:
1To turn the control on, press the “On/Off” button.
Note: For SelectTouch™, ComfortSet™, and ChoicePlus™ controls, the backlit display light will reset itself by
flashing “88” and then will return to the previous setting and will begin to warm.
2Note: For OneSet™ control, press the button to turn on to the lowest heat setting. Repeat pressing the
button to scroll to desired heat setting (5 total). To turn off, scroll through heat settings until all LED
indicator lights turn off.
3Adjust the warming setting to your personal comfort by rotating the top knob left or right for ChoicePlus™,
SimpliTouch™, and EasySet™ controls.
4Note: For SelectTouch™ and ComfortSet™ controls, press the large left button with the “-” sign to lower
the heat setting and the large right button with the “+” sign to increase your heat setting.
5To turn the heated blanket/mattress pad OFF, press the “On/Off” button.
CAUTION: ALWAYS turn the heated blanket/mattress pad “OFF” when not in use.
DesignSmart™ Controller
Selectable Auto Off:
You can set the auto-off time at 2hrs, 6hrs or 10hrs.
1To use the auto-off feature, Press the Mode button until the “Auto-Off” words begin to flash.
2While the “auto-off” is flashing, use the + (dimmer increase) and - (dimmer decrease) buttons to scroll
through the 3 auto off options.
Auto off will be set at the highlighted time. (The control will remember the auto off setting unless AC power is disconnected.
If no button is pressed after 6 seconds, the highlighted setting will be set.
Preheat:
The preheat function will heat the bed for a period of 30 minutes and the control will return to its
original setting.
1Press the mode button until “Preheat” appears on the screen. The preheat will then start.
2To turn off the Preheat feature press the mode button until the “Preheat” disappears from the screen or
press the On/Off button to power off the unit.
Heat Adjustment:
There are 10 settings from Low to Hi.
To adjust the heat setting, simply press the + (raise heat temp) or the – (lower heat temp) on the large
circular button in the center of the control.
Dimmer:
Your controller gives you the ability to adjust the brightness of the display.
To adjust the brightness, Press the + (dimmer increase) or the – (dimmer decrease) buttons to change the
brightness level.
ChoiceTouch™ Controller
Setting the clock:
1. Turn the unit over to find the Slide switch.
2. Slide the switch to Time Set. The clock will begin to flash.
3. Press the + (dimmer increase) or the – (dimmer decrease) buttons to scroll through the time. (if you hold down
the button, the time will scroll at a faster pace).
For questions or support, please visit www.sunbeam.com.
9
Note: there is a P to the right of the clock to denote PM.
4. Release the button to stop at the desired time.
5. When the desired time has been reached, slide the switch to the center position to save the time and return
to normal operation.
Note: The clock will blink until the time has been set.
The control will remember the time settings unless AC power is disconnected.
Selectable Auto Off:
You can set the auto-off time at 2hrs, 6hrs or 10hrs.
If the personalized options are not selected, the auto off feature is designed for conservation of energy by
automatically turning your blanket or mattress pad off after 10 hrs of continuous use.
To use the auto-off feature, Press the Mode button until the “Auto-Off” words begin to flash.
While the “auto-off” is flashing, use the + (dimmer increase) and - (dimmer decrease) buttons to scroll
through the 3 auto off options.
Auto off will be set at the highlighted time. (The control will remember the auto off setting unless AC power
is disconnected.
If no button is pressed after 6 seconds, the highlighted setting will be set.
Preheat:
The preheat function will heat the bed for a period of 30 minutes and the control will return to its original setting.
Your controller allows you to set the time that you would like your blanket to start preheating each night. That
way you can always get into a cozy warm bed.
To set the preheat time with a set time
1. Make sure the clock has been set. To set the clock, please see the clock set instructions.
2. Set the time you would like the pre-heat to come on.
3. Turn the unit over to find the Slide switch. (if the clock has not been set, please see clock set instructions.)
4. Slide the switch to Preheat Time Set. The clock and “Preheat will flash”. Press the + (dimmer increase) or
the – (dimmer decrease) buttons to scroll through the time. (if you hold down the button, the time will scroll
at a faster pace).
Note: there is a P to the right of the clock to denote PM.
4. Release the button to stop at the desired time.
5. When the desired time has been reached, slide the switch to the center position to save the time and return
to normal operation.
Note: The Preheat time will blink until you have set the Clock. Please set the Clock before you set the time you
would like preheat to start.
The control will remember the time settings unless AC power is disconnected.
To use the preheat function without setting the time
1. Press the mode button until Preheat flashes on the screen.
2. Press the + (dimmer increase) or – (dimmer decrease) to scroll through the options. Each press moves
changes the options as follows:
• Preheat On with the time displayed. This will set the preheat to turn on automatically at the pre-set time
displayed. If you do not press any button for 6 seconds, the preheat time will be set and the unit will be
ready to preheat at the set time.
• Preheat On without the time displayed. This will start the preheat when you leave the mode setting. You can
leave the mode setting by not pressing any button for 6 seconds.
• Preheat off. This stops any preheat functionality.
If no button is pressed after 6 seconds, the last setting will be stored.
10
For questions or support, please visit www.sunbeam.com.
Note: When the Preheat Mode is set to turn on at the set time, the clock display will show the time the blanket
will begin the preheat, not the actual time of day. This is to remind you when you have the blanket set to start
preheat.
Heat Adjustment:
There are 10 Heat level settings from Low to Hi.
To adjust the heat setting, simply press the + (raise heat temp) or the – ( lower heat temp) on the large
circular button in the center of the control.
Dimmer:
You can adjust the brightness of the display.
Press the + (dimmer increase) or the – (dimmer decrease) buttons to change the brightness level.
Heated Throw Setup
When setting up your heated throw, be sure to follow the steps below in order.
1 Locate the heated throw’s information label near the module.
2 Connect the cord into the module at the bottom of the heated throw until
the plastic hinges click into place. CAUTION: Cord must be COMPLETELY CONNECTED. A risk of fire
could result from a loose connection.
3 Plug the [heated throw] power cord into a 110-120 volt wall outlet.
CAUTION: Do not plug main power cord into the wall outlet until you have completely set up your heated
product per the instructions.
• Disconnect power cord from wall before detaching control from heated product.
• Always make sure cords and controls are NOT trapped or pinched between bed slats, mattress,
springs, against wall, foot board or bed frame, or between furniture, walls or chairs.
• Do not wrap control in throw when in use.
• Do not use with generator power.
Using Your Heated throw Control:
1 To turn on the throw press the button in the middle of the control.
The indicator light will glow, depending on which setting the heated
throw is set, and the heated throw will begin to warm.
CAUTION: ALWAYS turn the heated throw “OFF” and disconnect the power
cord from the outlet when not in use.
2 To turn the heated throw OFF press the button through the different
settings until the temperature setting lights are not glowing.
3
3
Flag Tag
If there is a flashing light
on your control, see page 8.
Flag Tag
Control
Control
Power
Cord
Power
Cord
1
1
2
Module
Throw Cord
Connector
Label
Throw Cord
2
Module
Throw Cord
Connector
For questions or support, please visit www.sunbeam.com.
Label
Throw Cord
11
Care and Cleaning OF YOUR HEATED BEDDING PRODUCT
We recommend washing before initial use.
Before Washing or Storing Your Heated Bedding Product:
1 Disconnect power cord from wall BEFORE detaching control cord from the heated product.
2 Ensure that no cords are still connected and none of the wires have worn through the fabric.
3 Carefully follow all washing instructions or your heated product may shrink and possibly
cause a fire hazard.
• DO NOT submerge control in water.
• DO NOT dry clean your heated product. Dry cleaning solvents may damage the wires.
• DO NOT use bleach or cleaning fluids.
• DO NOT use a wringer.
• DO NOT iron your heated product.
• DO NOT use mothballs or sprays of any kind.
• DO NOT reconnect the heated product or use it until it is COMPLETELY dry.
• DO NOT wash or put into water the power cord or any of the product’s cords.
• DO NOT use analgesic cream in combination with your heated product.
Taking care of your heated product is easy and safe as long as you follow a few simple steps.
Machine Washing
1 Presoak the blanket/mattress pad/throw for 15 minutes in mild soap and cold water.
2 Wash in mild soap and cold water on the “delicate” or “gentle” cycle in the washer
for two minutes. Remember, do not use bleach.
3 Rinse in fresh, cold water.
4 Spin dry in the washing machine. Then gently stretch to its original size.
Machine Drying
Caution: Do not use commercial dryers or the dryers at your local laundromat.
They get too hot and would damage the wiring of the heated product.
1 Preheat the dryer on the “low” temperature setting for 2 minutes.
2 Place blanket/mattress pad/throw into the dryer and tumble dry for 10 minutes at a low temperature.
3 Remove the blanket/mattress pad/throw while it is still damp and gently stretch it to its original size.
4 Drape the heated product over a clothesline or a shower rod. DO NOT use clothespins.
5 Heated product must be COMPLETELY dry before reconnecting the power plug or control plug.
Hand Drying
1 Gently stretch the blanket/mattress pad/throw back to its original size.
2 Drape the heated product over a clothesline or hang over a shower rod. DO NOT use clothespins.
3 Heated product must be COMPLETELY dry before reconnecting the power plug or control plug.
12
For questions or support, please visit www.sunbeam.com.
Frequently Asked Questions
ABOUT YOUR HEATED BEDDING PRODUCT
Q Who should NOT use the heated blanket, heated mattress pad or heated throw?
A The following people should NOT use the heated blanket, heated mattress pad
or warming throw:
• An infant
• A child
• An incapacitated or immobile person
• A paraplegic
• A quadriplegic
• A diabetic
• Anyone insensitive to heat such as a person with poor blood circulation
• Anyone who cannot clearly understand the instructions and/or operate the controls
Q What do I do if my pet chews the cord, I lose my control or the control does not
operate properly?
A Please stop using the heated product immediately. Call our Consumer Service number
listed under How to Obtain Warranty Service and ask for instructions on how and where to send
the heated product.
Q My control feels warm to the touch. Is this a problem?
A No. The control will feel warm to the touch when functioning properly.
Q My heated blanket/heated mattress pad/heated throw doesn’t heat properly.
A Your heated product is not a heating pad. It will not feel hot to the touch when laid out
flat in a normal manner. Try the following fold test to see if it is
operating properly:
1 Fold the heated blanket, heated mattress pad or warming throw 3
times over.
2 Make sure the control cord is connected to the module and then plug
the power cord into an outlet.
3 Turn on your heated product, then turn the control to the highest
setting and wait 5 to 7 minutes.
4 Put your hand between the folds and you should feel the blanket/ mattress pad/throw
warming up.
Caution: DO NOT continue the test for more than 7 minutes. DO NOT attempt to make any internal
adjustments to this appliance. If you have tried all of the solutions above and the heated product
still doesn’t work, stop using it immediately, disconnect the power cord and contact Sunbeam
Consumer Care.
For questions or support, please visit www.sunbeam.com.
13
Q What does “F” ,“FF”, “F1” or “F2” mean on my Electronic Digital Control?
A T he digital controls are designed to notify you in the event that a problem has been discovered
by flashing “FF”, “F1” or “F2” on the display.
Models: ChoicePlus™
Follow instructions below.
FF
F1
Models: SelectTouch™, ComfortSet™
Follow instructions below.
F2
Models: SelectTouch™, ComfortSet™
Follow instructions below.
F
Models: StyleSmart™ II, DesignSmart™, ChoiceTouch™
Follow instructions below.
1.) Follow the instructions on the flag tag attached to the control cord to reset control.
2.) Check the blanket/mattress pad for visual damage.
3.) If no visual damage is found, unplug the system from wall outlet.
4.) Check that the control is well-connected to the module.
5.) Plug the power cord into the wall outlet.
6.) Set the control to “On”.
7.) ­If the system does not operate after 2 or 3 times trying to reset, disconnect the power cord
and contact Sunbeam Consumer Care.
Q What does a flashing light mean on my OneSet™, EasySet™, PrimeStyle™ AO
or EliteStyle™ control?
A These controls are designed to notify you in the event that a problem has been discovered
by flashing the light on the control. Follow instructions on the flag tag to reset control. First,
check the heated product for visual damage. If no visual damage is found, unplug the system
from wall outlet. Check that the control is well-connected to the module. Plug the power cord
into the wall outlet and turn the control On. If the product still does not operate after 2 or 3
times trying to reset, disconnect the power cord and contact Sunbeam Consumer Care.
14
For questions or support, please visit www.sunbeam.com.
PLEASE DO NOT RETURN THIS PRODUCT TO PLACE OF PURCHASE.
Limited Warranty
Sunbeam Products, Inc. doing business as Jarden Consumer Solutions or if in Canada, Sunbeam
Corporation (Canada) Limited doing business as Jarden Consumer Solutions (collectively “JCS”) warrants
that for a period stated below from the date of purchase, this product will be free from defects in
material and workmanship.
• All heated products branded “Arlington™” will carry a ONE year limited warranty.
•All heated products branded “Sunbeam® HomeChoice™” will carry a TWO year limited warranty.
•All heated waterproof mattress pads will carry a THREE year limited warranty, with the exception of
“Arlington™” and “Sunbeam® HomeChoice™.”
•All other heated products branded “Sunbeam®” and “SlumberRest®” will carry a FIVE year limited
warranty, except heated waterproof mattress pads.
JCS, at its option, will repair or replace this product or any component of the product found to be defective
during the warranty period. Replacement will be made with a new or remanufactured product or component. If
the product is no longer available, replacement may be made with a similar product of equal or greater value.
This is your exclusive warranty. Do NOT attempt to repair or adjust any electrical or mechanical functions on
this product. Doing so will void this warranty.
This warranty is valid for the original retail purchaser from the date of initial retail purchase and
is not transferable. Keep the original sales receipt. Proof of purchase is required to obtain warranty
performance. JCS dealers, service centers, or retail stores selling JCS products do not have the right to
alter, modify or any way change the terms and conditions of this warranty.
This warranty does not cover normal wear of parts or damage resulting from any of the following:
negligent use or misuse of the product, use on improper voltage or current, use contrary to the operating
instructions, disassembly, repair or alteration by anyone other than JCS or an authorized JCS service
center. Further, the warranty does not cover: Acts of God, such as fire, flood, hurricanes and tornadoes.
What are the limits on JCS’s Liability?
JCS shall not be liable for any incidental or consequential damages caused by the breach of any express,
implied or statutory warranty or condition.
Except to the extent prohibited by applicable law, any implied warranty or condition of merchantability or
fitness for a particular purpose is limited in duration to the duration of the above warranty.
JCS disclaims all other warranties, conditions or representations, express, implied, statutory or otherwise.
JCS shall not be liable for any damages of any kind resulting from the purchase, use or misuse of, or
inability to use the product including incidental, special, consequential or similar damages or loss
of profits, or for any breach of contract, fundamental or otherwise, or for any claim brought against
purchaser by any other party.
Some provinces, states or jurisdictions do not allow the exclusion or limitation of incidental or
consequential damages or limitations on how long an implied warranty lasts, so the above limitations or
exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights that vary from
province to province, state to state or jurisdiction to jurisdiction.
For questions or support, please visit www.sunbeam.com.
15
PLEASE DO NOT RETURN THIS PRODUCT TO PLACE OF PURCHASE
We’re Here to Help, Please contact Jarden Consumer Care Centers listed below:
How to Obtain Warranty Service
In the U.S.A.
If you have any question regarding your heated product, this warranty or would like to obtain
warranty service, please visit our web site at: www.sunbeam.com or contact Jarden Consumer Care
at 1-800-892-7684 and a convenient service center address will be provided to you.
In Canada
If you have any question regarding your heated product, this warranty or would like to obtain
warranty service, please visit our web site at: www.sunbeam.com or contact Jarden Consumer Care
at: 1-800-667-8623 and a convenient service center address will be provided to you.
In the U.S.A., this warranty is offered by Sunbeam Products, Inc. doing business as Jarden Consumer
Solutions located in Boca Raton, Florida 33431. In Canada, this warranty is offered by Sunbeam Corporation
(Canada) Limited doing business as Jarden Consumer Solutions, located at 20B Hereford Street, Brampton,
Ontario L6Y 0M1. If you have any other problem or claim in connection with this product, please contact our
Consumer Service Department. PLEASE DO NOT RETURN THIS PRODUCT TO ANY OF THESE ADDRESSES OR
TO THE PLACE OF PURCHASE.
Printed in China
© 2014 Sunbeam Products, Inc. doing business as Jarden Consumer Solutions. All rights reserved.
Distributed by Sunbeam Products, Inc. doing business as Jarden Consumer Solutions, Boca Raton,
Florida 33431.
DW-012814
For inquiries regarding recycling and proper disposal of this product, please contact your local waste
management facility.
16
For questions or support, please visit www.sunbeam.com.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement