Technical and Specification Information Mechanical range Comfort range Advanced intelligent range Wave smart control Worcester Controls range NEW Greenstar Comfort controls 1 Worcester and you. Making a difference. 2 As part of the Bosch Group, Worcester supported by an experienced technical products are designed and manufactured to services team which is able to provide provide customers with the highest levels of comprehensive support and advice from quality and reliability which are synonymous designing system layouts through with the Bosch name throughout the world. to installation. As part of Europe’s largest supplier of Worcester is dedicated to providing energy heating products, Worcester, Bosch Group efﬁcient gas- and oil-ﬁred condensing has the UK-based resources and support boilers, as well as an extensive range of capability to offer you the value-added renewable technologies. All of our products solutions you deserve. Worcester employs have been developed and introduced with a nationwide network of Service Engineers the aim of helping the UK to achieve the and technically trained Field Sales Managers Government’s efﬁciency targets. The reception and main entrance at our Worcester headquarters “At Worcester we recognise the vital role you play in the specification and installation of energy efficient appliances in homes across Contents Page Why are controls so important? 4-5 Worcester’s complete controls range 6-7 The intelligent controls range 8 - 20 Greenstar wiring centre 21 Wave smart control 22 - 25 Training 26 - 28 After-sales 29 the UK. We will continue to invest in our products, people, facilities and added value services to ensure you have all you require in order to deliver only the best solutions to your customers’ requirements.” Carl Arntzen, Managing Director, Bosch Thermotechnology Ltd. 3 Why are controls so important? At Worcester, we believe in providing heating engineers with a range of choices that will enable them to provide the best solution for their customers. This philosophy is reﬂected in the breadth of our controls offering and our continued investment in developing new control technologies. Maximise energy efficiency Best practice Over the last few years boilers have become Minimum control performance meets the increasingly efﬁcient, with the best models demands of today’s energy-conscious now offering typical efﬁciencies of around homeowner and modern heating controls 91% - close to the maximum that can be are now much more accurate than achieved through the design of the 15 years ago. With energy prices set to boiler itself. continue rising for the foreseeable future, homeowners want maximum efﬁciency to So it makes sense to take a closer look at keep their bills down and to minimise their the other parts of the system where we can carbon footprint. improve performance – and the controls side is an obvious area to focus on. Building Regulations Current and future editions of the Building Homeowner savings Regulations are to demand higher levels of Though 10-15 years ago, saving 10% control to achieve greater efﬁciencies, while on a fuel bill would not have been very bringing them in line with the Code for signiﬁcant, nowadays depending on your Sustainable Homes. level of fuel consumption it could amount to as much as £150 and 630kg carbon dioxide* a year, very quickly covering the cost of the chosen control. 4 *Source: Energy Saving Trust Code for Sustainable Homes The Code for Sustainable Homes, which has been in effect since April 2007, introduced minimum standards in new homes for energy and water efﬁciency. The Energy-related Products Directive (ErP) The next phase of the ErP Directive, for introduction in 2015, will set Europe-wide rules for the energy efﬁcient design of heating products such as boilers. In the Directive, load compensation controls are recognised as improving the system efﬁciency by at least 3%. Intelligent control For all of these reasons, Worcester’s new generation of controls offer far more than a simple on/off control and have moved Smart heating and hot water control towards two-way communication between The new Worcester Wave smart control the boiler and room thermostat or weather allows users to take control of their heating compensation controller. system from anywhere in the world*. However, at the same time we understand Using a compatible Apple® iOS or Android™ that no matter how ‘clever’ controls get device with a dedicated app installed, they need to be easy for the homeowner homeowners can alter the heating to use, otherwise they won’t be able to programme from the ofﬁce, whilst travelling control their heating and hot water to its or on holiday. The heating schedule can full potential. Our simple user interface be updated at any time to allow for the allows the customer to grasp the important constant changes in routine that occur in functions of any control. many of today’s lifestyles. 5 year guarantee on Worcester controls When purchased and installed at the same time, the guarantee period for a Worcester control will match that of a Greenstar gas-ﬁred boiler**. *When an internet connection is available. **Terms and conditions apply. 5 Complete controls range Worcester offers a wide range of controls from basic mechanical programmers to an internet-enabled smart control. Whatever the end user’s speciﬁc preferences and budget, there is a Worcester control model to meet their needs. Simple-to-operate mechanical timer range MT10 mechanical timer Analogue control for setting daily times for central heating. The heating will start and ﬁnish at the same times every day. • Use the ‘teeth’ on the dial to set heating time periods • The MT10 can be used in conjunction with the FR10 Intelligent Room Thermostat. MT10RF mechanical RF thermostat There are two parts to the MT10RF, a transmitter and a receiver. They use radio frequency (RF) to communicate, which means there is no additional wiring required to install them. • Analogue display for setting night and day time periods and temperature • Heating can be set from the transmitter on the wall, no need to access the boiler. Greenstar oil-fired system and regular boiler programmer Twin channel 7-day digital programmer The optional plug-in programmer for the Greenstar Danesmoor System, Greenstar Danesmoor regular and Greenstar Danesmoor WM ranges. • Enables two heating and hot water on/off periods to be set for each day of the week • Incorporates a holiday setting • The digital unit plugs into the fascia panel • The wiring for the timer is easily plugged into a pre-prepared socket. 6 Sophisticated digital and wireless programmers and room thermostats Comfort range The Greenstar Comfort controls range from a plug-in programmer to an advanced wireless programmer and room thermostat. • Easy to install, no wiring required • Thermostats incorporate load compensation which assesses the output and temperature of the boiler and adjusts the ﬂow temperatures to heating demand • Easy to use with clear visualisation of heating programme and intuitive menu navigation • 7-day time control that can be programmed for up to six time periods per day, for heating and hot water. Advanced intelligent range Wired programmers and thermostats with a wide range of advanced features. • All controls in this range have load compensation and the FW100 has weather compensation • Separate times and temperatures for the heating and hot water can be set for each day of the week • Holiday function which suspends the normal heating and hot water times for the duration of the holiday and resumes them on return • FR110 and FW100 have integrated solar control when installed with the ISM1. Wave smart control The Wave is a smart, internet-connected programmable control for central heating and hot water which can be operated using a smart device. • Simple to ﬁt, just requiring a low voltage 2-core wire between the controller and the boiler – all other connections are via the Wi-Fi network • External wired sensor not required for weather compensation as the Wave uses online data instead • Intuitive and modern design ensures easy programming and control of the boiler resulting in a simple hand over with the end-user • Energy graphs, home presence detection and many more features come as standard to ensure increased comfort and energy savings. 7 The Greenstar Comfort controls range Worcester’s new Greenstar Comfort range of intelligent boiler controls has been developed by Worcester with the help of feedback from installers and end-users. As a result, they are our most advanced and simple to use controls yet – being easier to install and simpler to use, while producing a wider choice of programming options. The thermostats communicate with the Both heating and hot water can be altered boiler via a very reliable wireless signal. up to six times a day with different settings Therefore no wiring is required, making for each day of the week. This gives the them quick to install. homeowner the opportunity to programme their heating to ﬁt in with their varying Unlike many wireless controls that just send daily routines. on and off commands, they are able to have an intelligent conversation with the boiler. There are three models in the This enables load compensation, which Comfort range: assesses the output and temperature of the • Greenstar Comfort – plug-in twin boiler and adjusts the ﬂow temperatures to meet the heating demand, resulting in lower fuel bills. channel programmer • Greenstar Comfort I RF – wireless room thermostat and plug-in twin channel programmer • Greenstar Comfort II RF – wireless programmable room thermostat and plug-in RF receiver. 8 Technical data – Comfort range Controller model Comfort Comfort I RF Comfort II RF Height 110mm 110mm 111mm Width 133mm 133mm 134mm U U D D D D Rated current 2-wire BUS 2-wire BUS 2-wire BUS Control range 4 - 30ºC in steps of 0.1ºC 4 - 30ºC in steps of 0.1ºC 4 - 30ºC in steps of 0.1ºC 0 - 60°C 0 - 60°C 0 - 60°C Protection level 1PX2D 1PX2D (fascia mounted) IP20 (wall mounted) IP20 Control position Fascia mounted Programmer fascia mounted/ Thermostat wall mounted Wall mounted RF Load compensation Permissible ambient temperature Compatibility REGULAR Danesmoor WM SYSTEM Danesmoor Heatslave II External COMBI Heatslave II 27Ri and 30Ri REGULAR* 12i System and 24i System CDi Classic System 27i System and 30i System Highflow CDi i Junior Si Compact CDi Compact 2 CDi Classic Comfort controls Oil-fired boilers SYSTEM^ Danesmoor System Gas-fired boilers COMBI Part no. Comfort 7 733 600 003 Comfort I RF 7 733 600 001 Comfort II RF 7 733 600 002 D2 D D3 D1 D D2 D D3 D2 D D3 D1 D D2 D D3 D D2 D D3 D1 D D2 D D3 D D D4 D D4 D D4 *With optional wiring centre (see page 21). ^With optional integral diverter valve. 1 Manufactured after July 2013. 2 Manufactured after 16th January 2007 with software version CF12.10 onwards. 3 Manufactured after February 2011. 4 Must be used with Comfort wall plate kit. Correct at time of printing. For the latest list of compatible boilers see the Worcester website. 9 Comfort twin channel programmer This is a twin channel programmer that plugs directly into the boiler and requires a separate room thermostat (not included). Features and benefits • 7-day time control for heating and hot water • Three adjustable heating and hot water time periods • Pre-set heating and hot water programme • Clear back-lit display • Automatic adjustment to British summer/winter time • Clear visualisation of heating programme • Easy menu navigation • Holiday mode of which only frost protection will remain active throughout this programmable period. Quick to install Easy menu navigation The Comfort twin channel programmer simply plugs Navigation through the menu is also very straightforward, into the boiler, with a connection to a separate room simply requiring rotation of the push button to quickly scroll thermostat. Programming functions are then accessed through the options. directly on the programmer. Programme to fit the household’s routine Both the heating at hot water can be programmed to come on and off up to three times a day and this can be set differently for each day of the week to ﬁt in with the homeowner’s routine. Comfort wall plate kit Where the boiler is in a location that is difﬁcult to access, such as a garage or loft, an optional plate kit can be used to mount the controller on a wall, with a low voltage 2-core wire connection back to the boiler. Clear back-lit display The large, back-lit screen provides a clear and easy interface to key information such as current heating and hot water operation and programming options. Further information includes time and day, burner on indicator, fault codes and Easy to use Based on feedback from end users and installers, the control menu has been designed to provide exceptional and intuitive ease-of-use, enabling users to become familiar with the system very quickly and take advantage of all of the available control options. 10 central heating programme visualisation bar. Comfort I RF twin channel programmer and room thermostat The Comfort I RF twin channel model is an intelligent programmer that plugs into the boiler and is supplied with a separate room thermostat for adjustment of room set-points temperature. Features and benefits All the features of Comfort (page 10) while also including: • Load compensation for enhanced efﬁciency • Extremely reliable RF signal • RF signal strength indicator to identify best location • Pre-paired transmitter and receiver • Landlord function. Load compensation Extremely reliable RF signal The Comfort I and II RF thermostats are able to have an Using the latest RF (radio frequency) technologies for intelligent conversation with the boiler. This enables a maximum reliability, the Comfort I provides wireless load compensation function that is capable of delivering communication between the boiler room thermostat up to 3% savings, based on measurements documented transmitter. It includes a radio signal strength indicator in the ErP Directive (Energy-related Products Directive). menu to assist in ﬁnding the best location for the Load compensation works by comparing the actual room thermostat. temperature and the set-point temperature and adjusting ﬂow temperature accordingly to maintain a low return water Holiday mode temperature for maximum condensing. The system can very simply be set to holiday mode, during which time the heating system provides frost protection only, while the hot water is switched off. Landlord function A ‘landlord function’ for enabling a maintenance/ annual service date to be set is also available for social housing customers. 11 Comfort II RF twin channel programmer The Comfort II RF is the top of the range control with a plug-in RF receiver on the boiler and a wall-mounted programmer and room thermostat combined in one unit. Features and benefits All the features of Greenstar Comfort and Comfort I (pages 10 & 11) while also including: • Six adjustable heating temperatures for each set-point per day • Programme and control heating and hot water at the room thermostat – perfect for boilers that are not easily accessible • Additional installer functions. Programme and control your heating and hot water at the Installer functions room thermostat The Greenstar Comfort II RF control includes a number of The combined programmer and room thermostat can functions that are for exclusive use by the installer/service be mounted on a wall in the living space. This provides engineer for use during installation, commissioning, annual access to all control functions at a single, easily accessible servicing and to assist with fault-ﬁnding. Maintenance location. This is also particularly useful in situations where and boiler diagnostic features include detailed system the boiler is difﬁcult to access, such as in a garage or loft. information and diagnostic history. Straightforward menu The control’s functions can be accessed through a simple menu structure with a minimal amount of steps required to programme the preferred setting. The menu navigation is circular, when the last item on a ‘menu tree’ is reached it goes back to the start of the menu. Six heating set-points per day Availability of up to six heating set-points per day provides unparalleled ﬂexibility to align boiler operation to the precise occupancy patterns within the home. Clear visualisation of heating programme When in programming mode, a graphical display at the bottom of the screen shows the set heating times for the day. 12 Installing and commissioning the Greenstar Comfort range of controls Room thermostat mounting The accuracy of a room thermostat is dependent upon the installation location. Any radiator in the same room as the room thermostat should NOT have a thermostatic radiator valve ﬁtted. The room thermostat should be installed so that the overall temperature of the property is monitored, for example hallways or landings, and not be installed in a living room or room with supplementary heating. Commissioning Comprehensive installation and commissioning instructions can be found within the installation and user instructions supplied with the units. 1.0m 0.75m 1.2m Selecting the installation location 13 The advanced intelligent controls range Worcester offers a range of wired intelligent heating controls, designed to enhance the integral efﬁciency of our current Greenstar boilers and feature weather and load compensation. In the forthcoming ErP Directive (Energy- There are four models in the intelligent related Products Directive) that is part controls range: of new Europe-wide legislation, load • FR10 Intelligent Room Thermostat – compensation controls are recognised as improving system efﬁciency by at least 3% and weather compensation by 4%, resulting in lower fuel bills. can be used in conjunction with any external 230V programmer • FR110 Programmable Room Thermostat – Load Compensation Thermostat and programmer By using low voltage power the controls • FW100 Weather Compensation Controller – also avoid the need for compliance with Weather Compensation Thermostat and Part P of the Building Regulations. programmer with outdoor sensor • ISM1 Intelligent Solar Module – for use with either the FR110 or FW100 to provide control of the solar system. 14 Technical data – advanced intelligent controls Controller model FR10 FR110 FW100 ISM1 Height 85mm 119mm 119mm 110mm Width 100mm 134mm 134mm 156mm Depth 35mm 35mm 35mm 55mm Rated voltage EMS-BUS 10 – 24V DC 10 – 24V DC 10 – 24V DC 10 – 24V DC Rated voltage – – – 230V AC Rated current ≤ 3.5 mA 4A 6 mA 6 mA (exc. illumination) (exc. illumination) Controller output 2-wire BUS 2-wire BUS 2-wire BUS 2-wire BUS Maximum output per connection – – – 120W 5 – 30ºC in steps of 0.5ºC 5 – 30ºC in steps of 0.5ºC 5 – 30ºC in steps of 0.5ºC – 0 – +50ºC 0 – +50ºC 0 – +75ºC 0 – +50ºC IP20 IP20 IPX2D (fascia mounted) IP20 (wall mounted) IP44 Wall mounted Wall mounted Fascia mounted/ wall mounted Wall mounted Control range Permissible ambient temperature Protection level Controller position Compatibility REGULAR Danesmoor WM SYSTEM Danesmoor Heatslave II External COMBI Heatslave II 27Ri and 30Ri REGULAR* 12i System and 24i System Highflow CDi i Junior Si Compact CDi Compact 2 CDi Classic CDi Classic System 27i System and 30i System SYSTEM^ COMBI Intelligent controls Oil-fired boilers Danesmoor System Gas-fired boilers Part no. FR10 intelligent room thermostat 7 716 192 065 D2 D D3 D1 D D FR110 programmable room thermostat 7 716 192 066 D2 D D3 D1 D D2 D D3 FW100 weather compensation controller 7 716 192 067 D2 D D3 D1 D D2 D D3 ISM1 intelligent solar module 7 716 192 068 D2 D D3 Outdoor weather sensor 7 716 192 764 *With optional wiring centre (see page 21). ^With optional integral diverter valve. 1 Manufactured after July 2013. 2 Manufactured after 16th January 2007 with software version CF12.10 onwards. 3 Manufactured after February 2011. 4 Must be used with an external propriety 230V timer. Correct at time of printing. For the latest list of compatible boilers see the Worcester website. D D4 DD 15 FR10 Intelligent Room Thermostat The FR10 is an intelligent room thermostat that enables load compensation and will offer energy savings compared to standard on/off controls. It can be used in conjunction with your existing external 230V programmer. Features and benefits • Compatible with your existing external 230V programmers • Programmer and room thermostat separate, familiarity for end user • Large, clear display, simple dial adjustment • Easy for installer to explain operation • Hidden intelligence • No additional knowledge required for end user operation • Load compensation • Increased efﬁciency of condensing boiler. Load compensation The FR10’s load compensation feature means that, rather than just switching the boiler on and off, it will adjust the ﬂow temperature of the central heating water in line with set heating temperature requirements. The smaller the difference between the actual temperature and the set-point temperature, the lower the ﬂow temperature from the boiler. In this way the FR10 minimises boiler cycling so less energy is wasted in ﬁring up the boiler after each ‘off’ cycle. Wall mounted Typically, the FR10 is mounted on the wall in the same position in the property as a traditional thermostat. As with traditional thermostats, any radiators in the same space as the controller should NOT be ﬁtted with a thermostatic Easy to use radiator valve (TRV). Operation by the user is very similar to traditional thermostats, with a large clear display and simple dial for adjusting set-point temperature. Consequently, it is very easy to explain to the end user. 16 FR110 Programmable Room Thermostat The FR110 is an intelligent programmable room thermostat that enables load compensation for heating and time control of hot water systems. Features and benefits • Wall mounted, with clear back-lit display • Ease of use for the installer and end user • Programmable room thermostat • Varied temperatures throughout the day • Economy temperature • Integrated solar control using ISM1 • Removes need for separate Worcester TDS10 controller • Maximum beneﬁt and efﬁciency from solar installation • Load compensation • Increased efﬁciency of condensing boiler. Six heating and hot water set-points The controller provides the choice of six weekly heating programmes, with six switching points per day. When used with system boilers it also offers a weekly hot water programme with six switching points per day. On combi boilers the six switching points can be used to switch pre-heat on where the hot water will be delivered to the tap quickly, and energy saving economy mode where the pre-heat function is turned off. Pre-set heating programmes The FR110 offers three pre-set temperature proﬁles for added convenience. • Comfort setting (21ºC), typically for use in the morning and evening • Economy setting (15ºC), typically used to keep the building warm through the day • Frost protection (5ºC), for when the property is Load compensation Once installed, the FR110’s integral low voltage EMS Bus device communicates with the boiler’s built-in Heatronic unoccupied for long periods or the heating is off in 3 controls to provide load-compensated control that ﬁnely cold weather. tunes ﬂow water temperatures to heating demand. Battery back-up The resultant reduced boiler cycling and the fact that the Use of a low voltage supply from the mains, rather than boiler remains warm rather than frequently cooling down relying on battery power, provides a clearer display for the and heating up again provides energy savings compared to user and ensures they don’t have to worry about replacing older style controllers. batteries. For extra peace of mind, the controller is supplied with a battery that will provide up to six hours back-up. Integrated solar heating control The FR110 can also be used in conjunction with Worcester’s ISM1 Intelligent Solar Module (see page 20) to optimise use of renewable solar energy for water heating. 17 FW100 Weather Compensation Controller The FW100 is a weather compensation controller that enables the boiler to anticipate changes in heating demand in relation to external temperatures. It comprises a programmable indoor unit to control the boiler and an external sensor located on a north facing wall. Features and benefits • Wall or fascia mounted • Installation ﬂexibility • Factory set parameters • Quick to install and commission • Economy temperature • House never goes cold • Integrated solar control using ISM1 • Removes need for separate Worcester TDS10 controller • Solar optimisation • Maximum beneﬁt and efﬁciency from solar installation • Weather compensation • Increased efﬁciency of condensing boiler. Room thermostat and programmer combined The list below shows the key criteria that should be applied The FW100 combines the functions of a room thermostat when choosing the most appropriate controls and discussing and programmer and incorporates factory-set heat the options with the end user. If the answer to the majority curves for use with radiators, underﬂoor heating and fan of the questions below is ‘yes’, a weather compensation convectors, making commissioning very straightforward. controller would be the most suitable option. The units also include a manual override for the user to • Are there many rooms in the dwelling that are used boost or reduce heating if and when required. frequently and in different ways? • Does the dwelling contain windows that are facing in Multiple heating programmes The FW100 offers the user three weekly heating programmes, with six switching points per day and a weekly hot water programme with six switching points per day. different directions? • Does the home have an open ﬁre, gas ﬁre or other heat source that does not heat all rooms equally? • Does the end user want a higher degree of comfort control in all rooms? The FW100 is compatible with the ISM1 Intelligent Solar Module (see page 20). • Does the customer accept the pump will run more often if a higher degree of comfort and better energy utilisation are to be achieved? When to use weather compensation controllers rather than room thermostats There are a number of situations where weather compensation controllers will offer better control and higher comfort levels compared to room thermostats. In • Are TRVs installed in all rooms? • Are there factors that prevent the heating controller being installed in the living area? • Can an outdoor sensor be installed on a north facing wall? • Does the end user want to achieve optimum comfort with choosing the most appropriate solution for the end user, it minimum energy consumption and are they prepared to is important to understand how the system will be used and pay a little extra for enhanced control? the nature of the building. 18 Installing and commissioning the advanced intelligent range of controls Installation Siting The accuracy of a room thermostat is dependent upon the installation location. 1.0m Any radiator in the same room as the room thermostat should NOT have a thermostatic radiator valve ﬁtted. 0.75m The room thermostat should be installed so that the overall 1.2m temperature of the property is monitored, for example, hallways or landings and not be installed in a living room or room with supplementary heating. Electrical connections The Worcester range of intelligent controls does not require a 230V mains supply. Instead, connection is made to the boiler via the BUS connections on the Heatronic 3 circuit board within the appliance. All BUS connections are polarity free. Permissible cable lengths and cross sections are shown in the table below: Cable length Cross-section ≤ 80m 0.40mm2 ≤ 100m 0.50mm2 ≤ 150m 0.75mm2 ≤ 200m 1.00mm2 ≤ 300m 1.50mm2 Permissible cable lengths to FW100 outside temperature Selecting the installation location sensor: Cable length Cross-section ≤ 20m 0.75mm2 – 1.50mm2 Commissioning ≤ 30m 1.00mm2 – 1.50mm2 Comprehensive installation and commissioning instructions ≥ 30m 1.50mm2 can be found within the installation and user instructions supplied with the units. To avoid inductive interference, lay all BUS cables separately to lines of 230V or 400V (minimum spacing 100mm). In case of external inductive interference, screened cables should be used. This ensures that the cables are shielded from external interference (e.g. heavy current cables, overhead wires, transformer stations, radio and television sets, amateur radio stations, microwave ovens etc). 19 ISM1 Intelligent Solar Module The ISM1 is a specially designed interface that integrates a solar heating system with a solar-compatible weather or load compensation unit such as the FW100 or FR110. Features and benefits • All solar control via FR110 or FW100 controller • Only one control to explain to end user • Displays solar performance on FR110 or FW100 • End user can check solar input • Clear colour coded plug-in connections • Installation ease • Solar optimisation • Maximum beneﬁt and efﬁciency from solar installation. The ISM1 enables the hot water system to take heat from Connection – low voltage section with BUS connection the solar panels when the sun is shining and then bring the Permissible cable length between the Heatronic 3 with boiler back on when there is not enough sunshine available. BUS capability and the ISM1: In this way, the user gets maximum beneﬁt from solar Cable length Cross-section ≤ 80m 0.40mm2 Another major beneﬁt of this arrangement is that the end ≤ 100m 0.50mm2 user only needs one controller to control both the solar and ≤ 150m 0.75mm2 boiler systems, making the system much easier to use. The ≤ 200m 1.00mm2 in-built intelligence of the FR110 and FW100 ensure that ≤ 300m 1.50mm2 heating while ensuring that hot water is always available. solar-related information is only displayed when the ISM1 is connected, to avoid confusion. The ISM1 is compatible with Greenstar CDi Classic System boilers providing the optional integral diverter valve is used and has the potential to reduce energy consumption by 15% compared to conventional systems. To avoid inductive interference, lay all BUS cables separately to lines of 230V or 400V (minimum spacing 100mm). Solar panel and cylinder sensors Dedicated sensors for both the solar panel and the hot water cylinder are supplied with ISM1. When sensor leads are extended, apply the following lead Installation The following components may be supplied by the unvented domestic hot water cylinder manufacturers, please refer to the installation instructions. Alternatively they are available at plumber’s merchants. • High limit control • Solar return two port valve • Solar wiring centre. cross-sections: Cable length Cross-section ≤ 20m 0.75mm2 – 1.50mm2 ≤ 30m 1.00mm2 – 1.50mm2 ≥ 30m 1.50mm2 230V AC connection Mains voltage should only be installed to the terminals on the left of the ISM1 and under no circumstances be connected to the BUS or sensor terminals. 20 Greenstar Wiring Centre The innovative Greenstar Wiring Centre enables intelligent control of heating and hot water for systems using our higher output regular boilers, while also reducing the workload and saving time for the installer. Features and benefits • Allows digital timers and programmers to be used with a regular boiler – controls both heating and hot water • Enables properties to use a wireless room thermostat which allows a wider choice of controls options • Pump is wired directly into the Wiring Centre and not to the boiler • Simple system-type selector (S or Y plan) – simple, clear wiring connections • Up to three Greenstar Wiring Centres can be linked together to control up to eight zones • Supplied complete with cylinder sensor and unique retaining device • Compatible with Worcester Greenstore unvented cylinders and third party unvented and vented cylinders* • IP44 safety rating increases possible installation locations. Enabling plug-in, fascia mounted digital timers and Control options programmers for Greenstar 27Ri and 30Ri regular boilers The Greenstar Wiring Centre allows the Greenstar 27Ri and The Greenstar Wiring Centre is a major beneﬁt for installers 30Ri regular boilers to be compatible with the following and end users, allowing the use of Worcester’s plug-in RF Worcester plug-in controls: controls, including wireless models, to be used on the new • Comfort I RF • Comfort II RF. Greenstar 27Ri and 30Ri regular boiler. This enables digital timers and programmers to control the heating and hot water for regular boilers systems. The wiring centre clearly Boiler located in kitchen distinguishes whether the cylinder needs hot water or if the home needs heating and, to maximise comfort and Wiring Centre located in airing cupboard Fuse spur efﬁciency, responds by operating the boiler at different 10-way wiring centre temperatures for each. Pump Simple, time-saving installation An innovative feature of the Greenstar Wiring Centre is that it allows the pump to be wired into the wiring centre, 3-core, SL, N, E rather than going through the household between the airing cupboard and the boiler. In replacement installations, this DHW cylinder Existing boiler system layout means the existing 3-core cable between the boiler and Greenstar 27Ri and 30Ri boiler located in kitchen pump can be utilised to carry communication signals (EMSFuse spur Greenstar Wiring Centre located in airing cupboard Fuse spur BUS) from the wiring centre to the boiler. Experience shows Greenstar Wiring Centre this can save as much as half a day of installation time. Pump The Greenstar Wiring Centre uses simple, clear, colourcoded connections and is supplied with a cylinder sensor and unique retaining device as standard. 3-core, BUS, BUS, E Product info Part number DHW cylinder 7 738 110 116 System layout with a Greenstar Wiring Centre *Please check with the manufacturer. Makes replacement boiler installation much easier. 21 Wave smart control The Wave is a smart, internet-connected programmable control for central heating and hot water which can be operated using a smart device. The Wave’s innovative programming enables Adapting to the end user’s needs it to have an ‘intelligent conversation’ Each Wave unit is supplied with a pre-set with the boiler and take advantage of programme that can be easily modiﬁed to advanced control features such as weather suit the user’s requirements. The Wave’s and load compensation. advanced user features include: • ‘Pairing’ with up to eight devices, Enhanced energy efficiency automatically sensing when people are at In the forthcoming ErP Directive (Energy- home. Sensing to an individual device can related Products Directive) that is part of be turned off if required new Europe-wide legislation, smart controls • The Wave will remember preferred like the Wave are recognised as improving the system efﬁciency by at least 4%^, programme settings to make these resulting in lower fuel bills. programme’, requiring just a start and easily available and features a ‘holiday ﬁnish date The Wave’s energy efﬁciency features include: the Wave can also programme the hot • Charts of heating and hot water usage so water settings, providing additional energy that it is easy to identify where potential savings could be made • When the room temperature is turned 22 • Unlike some other smart heating controls, savings and comfort • For security and peace of mind, all of the Wave’s data is owned by the user, down a leaf symbol will appear to indicate ensuring no information is shared with additional savings are being made. other parties. *See Worcester website for details of compatible devices. ^4% savings are achieved when weather compensation mode is enabled. The factory default is load compensation which delivers 3% savings. Technical data – Wave Controller model Wave 145 x 100 x 27mm Dimensions (H x W x D) 802.11b/g Connection (Wi-Fi) 14.3 to 16.0V DC Voltage supply Consumption (maximum) 0.9W Weight 250g Permissible operating temperature 0 to 45°C Permissible relative humidity 10 to 90% Compatibility Wave REGULAR Danesmoor WM SYSTEM Danesmoor Heatslave II External COMBI Heatslave II 27Ri and 30Ri REGULAR 12i System and 24i System CDi Classic System 27i System and 30i System Highflow CDi i Junior Si Compact CDi Compact CDi Classic Smart control Oil-fired boilers SYSTEM^ Danesmoor System Gas-fired boilers COMBI Part no. 7 716 192 072 D2 D D3 D1 D D2 D D3 ^With optional integral diverter valve. 1 Manufactured after July 2013. 2 Manufactured after 16th January 2007 with software version CF12.10 onwards. 3 Manufactured after February 2011. Correct at time of printing. For the latest list of compatible boilers see the Worcester website. 23 Features and benefits • Only a low voltage 2-core wire connection between the controller and the boiler • Easy to install, all other connections are via the Wi-Fi network • Remote control of heating AND hot water via app • Programme the heating system from outside the home • Load and weather compensation via the internet (no outdoor sensor required) • Allows the boiler to modulate its performance to meet the needs of each household • Intuitive and modern design • Ensures easy programming and control of the boiler, resulting in a simple hand over with the end-user • Energy graphs, presence detection and many more features come as standard • Ensures increased comfort and energy savings • No subscription fees or chargeable app add-ons • One-off cost. Quick to install The Wave is quick and easy to install: • Only requires a 2-core wire connection between the control and the boiler EMS 2 Wire • All other connections are via the Wi-Fi network • The Wave does not need an external wired sensor Greenstar boiler Wave unlike standard weather compensation controls • The Wave uses online data which signiﬁcantly reduces installation time and cost to the end user. Wi-Fi signal Wi-Fi (in home) Simple to use, providing an easy handover External access (away from home) Router The Wave’s intuitive and modern design ensures it is very simple to operate using either its in-built touchscreen or the app from wherever you are. Each unit is supplied complete External access (away from home) with written instructions for an easy handover. In addition, short instructional videos can be viewed via the app. Internet Phone When updates to the Wave software are released the controller and app will be updated automatically and completely free of charge. If you lose your internet connection, the Wave will continue to operate as an intelligent heating and hot water controller, Wave compatible devices*: Apple® devices running iOS 5.1 and higher Android™ devices running 2.2, 2.3 or 4.0 and higher using the last saved programme settings. 24 *Correct at time of printing. For the latest list of compatible boilers see the Worcester website. Installing and commissioning the Wave smart control Installation Siting To install a Worcester Wave all you need is: min. 0.4m • Worcester Wave control • Worcester compatible boiler • Wi-Fi enabled broadband router – 802.11 b/g • Wave app on a compatible Apple® or Android™ device. . 1m The thermostat must be ﬁtted to an interior wall min and ensure there is sufﬁcient free space around the thermostat. The wall mounting plate can be ﬁtted directly min. 0.6m onto the wall, for example in the location of the previous thermostat. The Wave connects to the boiler’s EMS BUS connections only. Under no circumstances must the thermostat be connected to the boiler’s 230 volt connections or external 230 volt supply. Commissioning instructions can be found within the installation and user instructions supplied with the unit. In addition, step by step videos can be seen on our You-Tube site ≥1.2m 0.75m Comprehensive installation and commissioning min. 0.6m ≥1m www.youtube.com/worcesterboschgroup Selecting the installation location 25 Total training experience from Land’s End to John O’Groats Worcester has always been committed to setting the College-linked Learning industry standard for expert professional training and As well as offering training at our own centres, Worcester this is reﬂected in the scope and content of the courses, has established close partnerships with many colleges venues and options available. around the UK, equipping them with our latest products. We offer training on our entire range of domestic and Worcester has worked closely with leading colleges and commercial heating technologies as well as industry-led independent training centres for more than 20 years – a courses. All tuition is handled by expert heating specialists, successful enterprise which in 2007 was enhanced further combining classroom theory with, practical hands-on with the launch of the College Links Learning Scheme. experience. Keep up-to-date with legislation and experience hands-on-training with our new technologies. Mobile training We can also bring training to you. We have mobile vehicles To increase your skills, expertise and value in the fully equipped with operational Greenstar gas-ﬁred boilers, market place, trust Worcester’s unique and proven dry strip-down models and even a Greensource air to air total training concept. heat pump. Our 7.5 tonne mobile oil vehicle is also available for hands-on oil product training and OFTEC assessments. Training centres throughout the UK Worcester Call now for more information 0330 123 0166. Worcester’s award-winning, state-of-the-art Training Academy is an innovative and spacious high tech training arena at our headquarters in Worcester. Facilities include open-plan domestic training areas with life-size single- Training centres T storey brick buildings. Here installers can get to grips with College links training centres Greenskies solar thermal systems working with Greenstar gas appliances, clearly demonstrating the importance of system design and operation. Elgin Wakefield Opened in Summer 2013, the Wakeﬁeld Training and Dundee Assessment Academy boasts a large gas laboratory which features our entire range of Greenstar gas-ﬁred appliances, Johnstone a ﬂushing area, wet and dry boilers and a light commercial Borders Ayr area with a cascade of Worcester GB162 boilers. It also Durham contains a heat pump room with a full range of Greenstore ground source, Greensource air source and Greenstar Belfast Plus hybrid heat pumps with a courtyard for all external components. There is a solar room with fully working components from our entire Greenskies solar range and Burnley W Wakefield Dublin Clay Cross a pitched roof for practical training, as well as a large Wrexham commercial training room. Worcester West Thurrock and Clay Cross Tredegar West Thurrock Further academies are located at West Thurrock in Essex and Clay Cross in Derbyshire, both of which offer Wiltshire a comprehensive choice of courses. Camborne 26 Cambridge Paignton Gas-fired product courses As a market leader in gas-ﬁred condensing boilers, we aim Gas-fired condensing boiler courses to ensure the highest levels of competence and expertise • Greenstar CDi Classic gas-fired condensing combi boilers. • Greenstar CDi Compact and Greenstar Si Compact gas- in the installation of all Worcester Greenstar gas-ﬁred products. We run intensive training courses for installers, commissioning engineers and operatives involved with servicing and fault ﬁnding. Our comprehensive gas-ﬁred condensing boiler training courses include product overview, inspection and cleaning of components, CO and CO2 analysis of ﬂue gas, removal of compact hydraulics, service mode functions and fault fired condensing combi boilers. • Greenstar i Junior gas-fired condensing combi boilers. • Greenstar system & regular gas-fired condensing boilers. • Greenstar Highflow CDi & FS CDi Regular floor standing gas-fired condensing combi and regular boilers. • Greenstar Controls (covers MT10, MT10RF, NEW Greenstar Comfort range, NEW Wave internet connected room thermostat, FR10, FR110, FW100, and ISM1). ﬁnding on ‘live and demo’ appliances. Greenstar Overview CDi Classic CDi Compact & Si Compact i Junior System & Regular Highflow CDi & FS CDi Regular Controls Duration 1 Day 1 Day 1 Day 1 Day 1 Day 1 Day 1 Day Cost Free* Free* Free* Free* Free* Free* Free* D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D Guide to the varied range of control options that are available Worcester D D D D D D Clay Cross U U U U U U D D D D D D D D D D D D D D D D D D D D Training course covers Speciﬁcation Installation Commissioning Servicing Maintenance Course locations Wakeﬁeld West Thurrock College Links† Mobile† U U U U D D D U D D *A holding fee of £65 applies to free courses and is refunded on attendance of the course. If a booking is cancelled more than 10 working days before the course date, the fee will be fully refunded. The fee is non-refundable if a cancellation is made less than 10 working days before the course date. †Please contact Worcester Training for speciﬁc colleges and mobile dates. 27 Additional product and industry training courses The diversity of products in today’s heating industry gives you the opportunity to expand your expertise, whilst offering more choice to your customers. Worcester provides comprehensive training from all its academies on its entire range of technologies. Call us on 0330 123 0166 to order a full course training brochure or to book yourself onto a training course, alternatively, you can visit www.worcester-bosch.co.uk/training Oil-fired product courses Worcester commercial product courses • Greenstar Danesmoor & Heatslave II high efficiency • Greenspring CWi47 water heater. • GB162 overview. • GB162 domestic. • GB162 commercial. • Greenstar Heat Distribution Unit. • Commercial ACS training and assessment – CODNCO1. condensing oil-fired boilers. • Oil advanced fault finding. • OFTEC 50. • OFTEC 101/105e, OFTEC 600a and OFTEC 101/105e/600a. Renewable product courses Bosch commercial product courses • Renewables overview. • Greenskies solar. • Greenskies advanced solar. • Introduction to heat pumps. • Greenstore LECP ground source heat pumps. • Greensource air to air heat pumps. • Greensource air to water heat pumps. • Greensource split air to water heat pumps. • GB312 & GB402 overview. • Solar thermal product overview. • GWPL Gas Absorption Heat Pumps overview. • CHP overview. • Commercial controls overview. Industry focused courses • Hot water systems & safety. • Chemical water treatment. • Construction skills F-Gas training/assessment certification. • IDHEE domestic heating design. • Domestic ACS training and assessment – reassessment. CCN1 + 3 appliances. • QCF Level 3 Award – Air source and ground source heat pumps. – Air to water and split air to water heat pumps. – Solar thermal. • MCS Made Easy. • Green Deal. • LPG Changeover. • WRAS Water Regulations. 28 A complete after-sales service As part of the worldwide Bosch Group, Worcester strives to Spares maintain the highest possible standards of after-sales care. Genuine replacement parts for all supported Worcester products are readily available from stock, or on a next day Worcester Contact Centre delivery basis. Visit www.worcester-bosch.co.uk/spares Should you require support, our award winning Contact to ﬁnd your local stockist. Centre team, based at our head ofﬁce in Worcester, are ready to take your calls. Whatever your query our contact Customer Technical Support centre operators along with our nationwide team of The Worcester Technical Helpline is a dedicated phone engineers are ready to help you. line – committed to providing a comprehensive service to complement the brand name and quality of our products. Tel: 0330 123 9559 Our experienced team of technical experts provides answers to queries of a technical nature across the entire Opening times Worcester range. Monday – Friday: 7.00am – 8.00pm Saturday: 8.00am – 5.00pm Technical Support Sunday: 9.00am – 12 noon Tel: 0330 123 3366 Bank Holidays: 8.00am – 4.30pm Fax: 01905 752 741 Email: [email protected] Opening times Monday – Friday: 7.00am – 8.00pm Saturday: 8.30am – 4.00pm Bank Holidays: 8.00am – 4.30pm 29 Notes 30 Notes 31 Useful numbers Customer Service Sales Engineer Appointments Tel: 0330 123 9669 Email: [email protected] [email protected] or telephone 0330 123 9339 Spare Parts Service Enquiries Tel: 0330 123 9779 Email: [email protected] [email protected] or telephone 0330 123 9559 Technical Helpline (Pre & Post Sales) Guarantee Registration Tel: 0330 123 3366 To register your Worcester guarantee, [email protected] please visit our website www.worcester-bosch.co.uk/registration Renewables Technical Helpline or telephone 0330 123 2552 Email: [email protected] or telephone 0330 123 9229 Training Tel: 0330 123 0166 [email protected] Literature Email: [email protected] or download instantly from our website or telephone 0330 123 9119 Calls to 03 numbers cost no more than a national rate call to an 01 or 02 number and must count towards any inclusive minutes in the same way as 01 and 02 calls. These rules apply to calls from any type of line, including mobile, BT, other ﬁxed phone line or payphone. Calls from mobiles and some other networks may vary. Calls to and from Bosch Thermotechnology Ltd may be recorded for training and quality assurance purposes. worcester-bosch.co.uk In partnership with FD TE O OMEST I ITU D H E 1964 E S ER I TAL ENG INE MEN ON NG & EN EATI VIR CH INS T This leaﬂet is accurate at the date of printing, but may be superseded and should be disregarded if speciﬁcation and/or appearances are changed in the interest of continued improvement. The statutory rights of the consumer are not affected. Apple is a trademark of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc. Google Play and Android are trademarks of Google Inc. Part No. 8 716 115 653 E 01/15 PAPERS MADE WITH FREE TM 100% CHLORINE BLEACHED PULP Worcester, Bosch Group, Cotswold Way, Warndon, Worcester, WR4 9SW BBT3450 Worcester, Bosch Group is a brand name of Bosch Thermotechnology Ltd.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project