OWNER'S MANuAL
PROPANE CONSTRUCTION CONVECTION HEATER
OWNER’S MANUAL
200
000
BTU/
HR
VARIABLE 40-80,000 Btu/Hr
75-200,000 BTU/HR
IMPORTANT: Read and understand this manual before
assembling, starting or servicing heater. Improper use
of heater can cause serious injury. Keep this manual for
future reference.
GENERAL HAZARD WARNING:
Failure to comply with the precautions and instructions
provided with this heater, can result in death, serious
bodily injury and property loss or damage from hazards
of fire, explosion, burn, asphyxiation, carbon monoxide
poisoning and/or electrical shock.
Only persons who can understand and follow the instructions should use or service this heater.
If you need assistance or heater information such as an instructions manual, labels, etc. contact the manufacturer.
Table of Contents
Safety Informa ion................................................ 2
Maintenance......................................................... 7
Unpacking............................................................ 3
Troubleshooting.................................................... 8
Theory of Operation............................................. 3
Specifications....................................................... 9
Product Identification............................................ 3
Replacement Parts............................................... 9
Ventilation ............................................................ 3
Technical Services................................................ 9
Propane Supply.................................................... 4
Accessories.......................................................... 9
Installation............................................................ 4
Illustrated Parts Breakdown and Parts List........ 10
Operation.............................................................. 5
Warranty and Repair Service............................. 14
Storage................................................................. 7
Save this manual for future reference.
For more information, visit www.desatech.com
Safety Information
WARNING: This product
contains and/or generates
chemicals known to the State
of California to cause cancer or
birth defects or other reproductive harm.
WARNING: Fire, burn inhalation and explosion hazard. Keep
solid combustibles, such as building materials, paper or cardboard,
a safe distance away from the
heater as recommended by the
instructions. Never use the heater
in spaces which do or may contain
volatile or airborne combustibles
or products such as gasoline, solvents, paint thinner, dust particles
or unknown chemicals.
WARNING: Not for home or
recreational vehicle use.
The heater is designed for use as a construction heater in accordance with ANSI
Z83.7•CGA 2.14. Other standards govern the
use of fuel gases and heating products for specific uses. Your local authority can advise you
about these. The primary purpose of construction heaters is to provide temporary heating
of buildings under construction, alteration or
repair. Properly used, the heater provides safe
economical heating. Products of combustion
are vented into the area being heated.
We cannot foresee every use which may be
made of our heaters. Check with your local fire safety authority if you have
questions about heater use.
Other standards govern the use of fuel gases and
heat producing products for specific uses. Your
local authorities can advise you about these.
Carbon Monoxide Poisoning: Some people are
more affected by carbon monoxide than others. Early signs of carbon monoxide poisoning
resemble the flu, with headaches, dizziness
and/or nausea. If you have these signs, the
heater may not be working properly. Get fresh
air at once! Check for proper ventilation and
have heater serviced.
Propane Gas: Propane gas is odorless. An
odor-making agent is added to propane gas.
The odor helps you detect a propane gas
leak. However, the odor added to propane
gas may fade. Propane gas may be present
even though no odor exists.
Make certain you read and understand all
warnings. Keep this manual for reference. It
is your guide to safe and proper operation of
this heater.
1. Install and use heater with care. Follow all
local ordinances and codes. In the absence
of local ordinances and codes, refer to
the Standard for Storage and Handling of
Liquefied Petroleum Gas, ANSI/NFPA 58
Natural Gas Installation Code, CAN/CGA
B149.2. This instructs on the safe storage
and handling of propane gases.
2. This product has been approved for use in
the Commonwealth of Massachusetts.
3. Use only propane gas set up for vapor
withdrawal.
4. Provide adequate ventilation. Before using heater, provide at least a 2.5 square
foot (0.232 m2) (80,000 btu heaters) or
6.0 square foot (0.557 m2) (200,000 btu
heaters) opening of fresh, outside air.
5. For indoor use only. Do not use heater
outdoors.
6. Keep heater away from strong drafts,
wind, water spray, rain or dripping water.
7. Do not use heater in occupied dwellings
or in living or sleeping quarters.
8. Do not use heater in a basement or below
ground level. Propane gas is heavier than
air. If a leak occurs, propane gas may sink
to the lowest possible level.
9. Keep appliance area clear and free from
combustible materials, gasoline, paint
thinner and other flammable vapors and
liquids. Dust is combust ble. Do not use
heater in areas with high dust content.
10.Minimum heater clearances from combustibles: 80,000 Btu heaters
Sides: 3 feet (91 cm); Top: 6 feet (1.83 m)
100-200,000 Btu heaters
Sides: 3 feet (91 cm); Top: 7 feet (2.1 m)
11.Keep heater at least six feet (1.83 m) from
propane tank(s).
12.Keep propane tank(s) below 100° F
(37.8° C).
13.Use only the hose and factory preset
regulator provided with the heater.
14.Check heater for damage before each
use. Do not use a damaged heater.
www.desatech.com
119588-01A
SAFETY INFORMATION
Product
Identification
Continued
15.Check hose before each use of heater. If
highly worn or cut, replace with hose specified by manufacturer before using heater.
16.Do not alter heater. Keep heater in its
original state.
17.Do not use heater if altered.
18.Locate heater on stable and level surface
if heater is hot or operating.
19.Not intended for use on finished floors.
20.Never block air inlet (bottom of shell) or
air outlet (around top of shell) of heater.
21.Do not leave heater unattended.
22.Keep children and animals away from
heater.
23.Always run heater with control knob at
LO, MED or HI settings. Never set control
knob between OFF, LO, MED or HI settings. Flashback may occur.
24.Never move, handle or service a hot
or operating heater. Severe burns may
result. You must wait 15 minutes after
turning heater off.
25.To prevent injury, wear gloves when handling heater.
26.Never attach duct work to heater.
27.Turn off propane supply to heater when
not in use.
28.Use only original replacement parts. This
heater must use design-specific parts.
Do not substitute or use generic parts.
Improper replacement parts could cause
serious or fatal injuries.
Unpacking
1. Remove all packing items applied to
heater for shipment. Keep plastic cover
caps (attached to inlet connector and
hose/regulator assembly) for storage.
2. Remove all items from carton.
3. Check all items for shipping damage. If
heater is damaged, promptly inform dealer
where you bought heater.
Outer
Shell
Ignitor
Button
200,0
00 B
TU/H
R
Valve
Ball Valve
Inlet
Control Knob
Safety Pilot Valve
Button
Figure 1 - 200,000 Btu Model Shown
Ventilation
WARNING: Provide at least
a 2.5 square foot (0.23 m 2)
opening of fresh, outside air
while running heater. If proper
fresh, outside air ventilation is
not provided, carbon monoxide
poisoning can occur. Provide
proper fresh, outside air ventilation before running heater.
Theory of Operation
The Fuel System: The hose/regulator assem-
bly attaches to the propane gas supply. This
provides fuel to the heater.
The Ignition System: The piezo ignitor lights
the pilot.
The Automatic Control System: This system
causes the heater to shut down if the flame
goes out.
119588-01A
www.desatech.com
Propane Supply
You must provide propane gas and propane
tank(s).
Use this heater only with a propane vapor
withdrawal supply system. See Chapter 5
of the Standard for Storage and Handling
of Liquefied Petroleum Gas, ANSI/NFPA 58
and/or CAN/CGA B149.2. Your local library or
fire department will have this booklet.
This heater will operate with a 20 pound (9.07
kg) propane tank. However, you can only
operate it in the LOW position during mildly
cool weather for a very short time. At higher
heat settings or during colder weather, you
must use larger tanks.
The amount of propane gas ready for use from
propane tanks varies. Two factors decide this
amount.
1. The amount of propane gas in tank(s)
2. The temperature of tank(s)
The chart below shows the minimum number
of 100 pound (45 kg) tanks needed to run
the heater. Connect tanks together with a
manifold.
Average Temperature
At Tank Location
(80,000 Btu models)
Number
Of Tanks
20° F (-6.7° C) to 60° F (15.6° C)
0° F (-17.8° C) to 20° F (-6.7° C)
1
2
(200,000 Btu models)
20° F (-6.7° C) to 60° F (15.6° C)
2
0° F (-17.8° C) to 20° F (-6.7° C)
3
Less gas is vaporized at lower temperatures.
Your local propane gas dealer will help you
select the proper supply system.
Installation
WARNING: Review and understand the warnings in the
Safety Information section, page
2. They are needed to safely operate this heater. Follow all local
codes when using this heater.
CAUTION: Never ignite and/
or run this heater unless the
shells are fully extended and
locked into position.
outer shell
IMPORTANT: When the heater is first removed from carton, the outer shell is in the
down position. Protect hands before lifting
outer shell. Never grasp bare metal without
hand protection.
1. Care must be taken to protect hands during this step. Lift outer shell straight up
as shown in Figure 2, until all three clips
engage slots in lower shell. Screw holes
will line up at this point.
2. Lock clips into place with 3 screws as
shown in Figure 2. The heater must not be
operated unless the outer shell is properly
extended and fully locked into place.
Outer
Shell
200
000
BTU/
HR
Clip in Slot
of Lower 3 Screws
per Clip
Shell
Figure 2 - Lifting Outer Shell
(200,000 Btu Model Shown)
Connecting to Gas Supply
WARNING: Test all gas piping
and connections for leaks after
installation or servicing. Never
use an open flame to check for
a leak. Apply a mixture of liquid
soap and water to all joints.
Bubbles forming show a leak.
Correct all leaks at once.
1. Provide propane supply system (see
Propane Supply).
2. Connect fuel gas fitting on hose/regulator
assembly to propane tank(s). Turn fuel
gas fitting counterclockwise into threads
on tank. Tighten firmly using a wrench.
IMPORTANT: Tighten regulator with vent
pointing down. Pointing vent down protects regulator from weather damage.
3. Connect hose to the valve inlet. Tighten
firmly using a wrench. You must use the
regulator supplied with heater even if propane tank has one.
www.desatech.com
119588-01A
Installation
Operation
Continued
4. Open propane supply valve on propane
tank(s) slowly. Note: If not opened slowly,
excess-flow check valve on propane tank
may stop gas flow. If this happens, you
may hear a click inside the regulator assembly, this is the check valve closing. To
reset the excess flow check valve, close
propane supply valve and open again
slowly.
5. Check all connections for leaks. Apply
mixture of liquid soap and water to gas
joints. Bubbles forming show a leak that
must be corrected.
Hose
Propane Supply
Valve
Propane
Tank
Regulator
POL
Fitting
Figure 3 - Regulator Position
Hose
Valve Inlet
Figure 4 - Hose and Valve Inlet
(200,000 Btu Model Shown)
WARNING: Review and understand the warnings in the
Safety Information section, page
2. They are needed to safely operate this heater. Follow all local
codes when using this heater.
80,000 Btu heater
To Start Heater
1. Follow all installation, ventilation and
safety information.
2. Locate heater on stable and level surface.
Make sure strong drafts do not blow on
heater.
3. Make sure unit is turned off by slightly
depressing and turning control knob fully
clockwise to OFF.
4. Open propane supply valve on propane
tank(s) slowly. Note: If not opened slowly,
excess-flow check valve on propane tank
may stop gas flow. If this happens, you may
hear a click inside the regulator assembly,
this is the check valve closing. To reset the
excess flow check valve, close propane
supply valve and open again slowly.
5. Slightly depress and turn control knob
counterclockwise to the LO position (see
Figure 5).
6. With the control knob pushed all the way
in, press and release the piezo ignitor
button. Keep pressing piezo ignitor button until the burner lights. Hold control
knob down for a maximum of 15 seconds
while attempting ignition. If heater does
not ignite, release control knob and wait
3 minutes before attempting to reignite.
7. After ignition, hold control knob down
for about 30 seconds. This activates the
automatic control system.
Control Knob
Off/
Apagado/
Arrêt
Lo/Bajo/
Bas
Med/
Medio/
Moyen
Hi/Alto/
Haut
Piezo Ignitor Button
Figure 5 - Control Knob and Piezo Ignitor
119588-01A
www.desatech.com
OPERATION
Continued
8. When burner remains lit, set heater at the
desired heat level by slightly depressing
the control knob and turning it counterclockwise to the MED or HI settings (see
Figure 5, page 5).
9. If burner goes out, turn off gas. Slightly depress and turn control knob fully clockwise
to OFF. Check fuel supply. If adequate
fuel is available, restart heater beginning
at step 1, page 5.
CAUTION: Always run heater
with control knob at LO, MED or HI
settings. Never set control knob
between OFF, LO, MED or HI settings as flashback may occur.
Yellow
Flame
Blue
Flame
Flame Inside
Burner Tube
(makes
roaring
noise)
Figure 7 - Incorrect Flame Pattern During
Flashback
Flame Patterns
Figure 6 shows a correct flame pattern. The
burner flame is mostly blue with a slight yellow
coloring on the ends.
Figure 7 shows an incorrect flame pattern.
The flame is mostly yellow. The incorrect
flame pattern results from low gas pressure
or from flashback.
Slight Yellow
Coloring on
Flame Ends
CAUTION: Running heater
between settings may cause
flashback. During flashback, the
burner flame is mostly yellow.
The flame will burn inside the
burner tube, causing a roaring
noise. If flashback occurs, turn
heater off. After burner tube
cools, restart the heater.
To Stop Heater
Blue
Flame
Burner
Tube
1. Tightly close propane supply valve on
propane tank(s). Allow heater to burn
remaining fuel in hose.
2. Shut off burner. Do this by pushing in the
control knob and turning clockwise to the
OFF position.
To Restart Heater
1. Wait five minutes after stopping heater.
2. Restart heater by following To Start
Heater, page 5.
Figure 6 - Correct Flame Pattern at High
Position
WARNING: Review and understand the warnings in the
Safety Information section, page
2. They are needed to safely operate this heater. Follow all local
codes when using this heater.
www.desatech.com
119588-01A
OPERATION
Storage
Continued
CAUTION: Disconnect heater
from propane supply tank(s).
200,000 BTU/HR HEATER
To Start Heater
1. Before lighting pilot fully close the ball
valve (turn knob fully clockwise).
2. Fully open the valve on the propane
cylinder and wait 15 seconds before
proceeding to step 3.
3. Depress red button on safety pilot valve
admitting gas to the heater. Then push
and release the ignitor button until the
pilot lights.
4. When the pilot lights, continue to hold the
button depressed for 30 seconds, then
release.
5. If pilot goes out, wait 5 minutes and repeat
the lighting procedure.
6. When the pilot remains lit, open the ball
valve (turn knob counterclockwise) to
light main burner. Partially close valve to
regulate heat output.
Ignitor
Button
Ball Valve Control
Knob Button
Safety Pilot
Valve
Figure 8 - Starting Heater
TO STOP HEATER
1. Securely close valve on the propane
cylinder.
2. Continue to operate heater until all fuel in
the hose has burned.
3. Fully close the ball valve.
TO RESTART HEATER
1. Securely close valve at propane cylinder.
2. Wait 5 minutes.
3. Restart heater by following To Start
Heater, page 6.
119588-01A
CAUTION: Be careful not to
locate fingers in groves on side
of heater, in vent holes or on
bottom of shell when collapsing shell to the down position.
Severe cuts may occur. Always
wear hand protection when
grasping bare metal.
1. The heater should be inspected before
each use and at least annually by a qualified person.
2. Before each use, check the soft "O" ring
seat at the bullnose of the POL fitting. If
the "O" ring is cut, scuffed or otherwise
damaged, replace the POL fitting with part
number LPA4020.
3. Turn off the gas at the propane/LP gas supply
cylinder(s) when the heater is not in use.
4. Heater is to be stored indoors. The connection between propane/LP gas supply
cylinder(s) and heater must be disconnected, cylinder(s) removed from the heater
and stored outdoors in accordance with
Chapter 5 of the Standard for Storage and
Handling of Liquefied Petroleum Gases
ANSI/NFPA 58 and CSA B149.1, Natural
Gas and Propane Installation Code.
5. Store in a dry, clean and safe place.
Maintenance
WARNING: Never attempt
to service heater while it is
connected to propane supply,
operating or hot. Severe burns
can occur.
1. Keep heater clean.
2. Inspect heater before each use. Check
connections for leaks. Apply mixture of
liquid soap and water to connections.
Bubbles forming show a leak that must
be corrected. Correct all leaks at once.
3. Inspect hose/regulator assembly before each
use. If hose is highly worn or cut, replace.
4. Have heater inspected yearly by a qualified service person.
www.desatech.com
Troubleshooting
WARNING: Never service heater while it is plugged in, connected
to propane supply, operating or hot. Severe burns and electrical
shock can occur.
OBSERVED FAULT
POSSIBLE CAUSE
Burner fails to light
1.Propane supply valve 1.Open propane supply valve
slowly
closed on propane tank(s)
2.Excess flow check valve 2.Close propane supply valve
on propane tank and reclosed
open slowly
3.Blockage in burner orifice 3.Replace burner orifice
4.Piezo ignition system not 4.Check to assure ignitor
electrode gap is 0.195"
sparking
Check wire lead for damage. Replace piezo ignitor
and/or ignitor electrode as
necessary
5.Clean or replace pilot as5.Pilot orifice clogged
sembly
(200,000 Btu models only)
REMEDY
Pilot lights but goes out when 1.Not enough warm up time
automatic control valve button is released (200,000 Btu
models only)
2.Low gas pressure
1.Relight, hold automatic
control valve button in 45
seconds
2.Check propane tank(s) for
proper gas supply
3.Thermocouple loose or 3.Tighten connection or replace thermocouple
needs to be replaced
4.Automatic control valve 4.Replace automatic control
valve
needs to be replaced
Burn rate is low
1.Control valve is on LOW
2.Plugged gas orifice
3.Low gas pressure
4.Low fuel supply
www.desatech.com
1.Turn valve counter clockwise to HIGH
2.Replace gas orifice
3.Check gas supply; check
regulator output
4.Consult propane gas supplier
119588-01A
Specifications
80,000 Btu
200,000 Btu
• Rating: 40,000 - 80,000 Btu/hr (11.72
- 23.4 kW)
• Type of Gas: Propane/LP Only
• Gas Supply Pressure to regulator: Maximum - Bottle Pressure, Minimum - 5 psig
(34.5 kPa)
• Gas Supply Pressure regulator out:
25" W.C. (63.5 cm)
• Ignition: Piezo Ignitor
• Minimum Ambient Temp Rating:
0° F (-17.8° C)
• Fuel Consumption/hr: 1.85 - 3.71 lb
(0.83 – 1.68 kg)
• Fuel Orifice Port No.: 1
• Fuel Orifice Port Size: 0.086" (2.18 mm)
• Rating: 75,000 - 200,000 Btu/hr (22.0
- 58.6 kW)
• Type of Gas: Propane/LP Only
• Gas Supply Pressure to regulator: Maximum - Bottle Pressure, Minimum - 15 psig
(103 kPa)
• Gas Supply Pressure regulator out:
10 psig (68.9 kPa)
• Ignition: Piezo Ignitor
• Minimum Ambient Temp. Rating: 0° F (17.8° C)
• Fuel Consumption/hr: 3.48 - 9.28 b
(1.58 - 4.21 kg)
• Fuel Orifice Port No.: 6
• Fuel Orifice Port Size: 0.032" (0.813 mm)
Replacement Parts
WARNING: Use only original
replacement parts. This heater
must use design-specific parts.
Do not substitute or use generic
parts. Improper replacement
parts could cause serious or fatal injuries. This will also protect
your ­warranty coverage for parts
replaced under warranty.
Parts Under Warranty
Contact authorized dealers of this product. If
they can’t supply original replacement part(s),
either contact your nearest Parts Central or
call DESA Heating Products’ Technical Service Department at 1-866-672-6040.
When calling DESA Heating Products, have ready
• your name
• your address
• model number of your heater
• how heater was malfunctioning
• purchase date
Technical Services
You may have further questions about
this heater. If so, contact DESA Heating
Products’ Technical Service Department
at 1-866-672-6040. When calling, please
have your model and serial numbers of your
heater ready.
You can also visit DESA Heating Products’
Technical Service web site at
www.desatech.com.
Accessories
Purchase heater accessories and parts from
your nearest dealer or service center. If they
can not supply an accessory or part, either
contact your nearest Parts Central (listed
in the separate Authorized Service Center
booklet) or call DESA Heating Products’
at 1-866-672-6040. You can also write to
the address listed on the back page of this
manual.
Parts Not Under Warranty
Contact authorized dealers of this product. If
they can’t supply original replacement part(s),
either contact your nearest Parts Central
(listed in Authorized Service Center booklet)
or call DESA Heating Products at 1-866-6726040 for referral information.
When calling DESA Heating Products, have ready
• model number of your heater
• the replacement part number
119588-01A
www.desatech.com
Illustrated Parts Breakdown
Models
TC106, TC112, TC113, TC114 AND TC115
1
2
6
7
8
9
23
5
11
10
12
3
16
13
14
17
15
18
19
20
22
21
10
4
www.desatech.com
119588-01A
Parts List
Models
TC106, TC112, TC113, TC114 AND TC115
This list contains replaceable parts used in your heater. When ordering parts, follow the
instructions listed under Replacement Parts on page 9 of this manual.
KEY
NO. PART NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
Cap
Upper Shell
Lower Shell
Ring Shield
Base
Ignitor Electrode
Thermocouple Bracket
Thermocouple
Thin Hex Nut
Piezo Ignitor Kit
Valve Retainer Nut
Control Knob
Nozzle Locator
Nozzle
Fuel Tube Kit
Burner Tube Kit
Brass Hex Cap
Automatic Valve
Adapter, 1/4 FPT x 1/4 MPT
Female Elbow Fitting, 1/4 FPT x 3/8 FLR
Hose/Regulator Assembly, 10 foot
Tube Fitting
Shoulder Screw
113785-01
113781-01
113825-01
113778-01
**
116617-01
103854-01
113790-01
100898-01
102445-01
098508-01
099393-03
117166-01
116556-01
116570-01
103929-01
099460-01
116554-01
117059-01
113795-01
115626-01
117060-01
099230-02
QTY.
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
PARTS AVAILABLE - NOT SHOWN
117069-02 80,000 Btu Rating Decal
113808-07 Hang Tag (English)
113808-08 Hang Tag (Spanish)
113808-09 Hang Tag (French)
113805-04 Installation Decal (English)
113805-05 Installation Decal (Spanish)
113805-06 Installation Decal (French)
113802-17 Model Decal
116558-01 Control Position Decal
**Not a field replaceable part
119588-01A
www.desatech.com
1
1
1
1
1
1
1
1
1
11
Illustrated Parts Breakdown
Models
200C, RCP200V(A), SPC-200C, tC107 and TC200V(A)
12
10
9
1
25
8
17
27
24
29
13
23
7
5
6
23
15
16
20
14
22
19
18
3
11
21
4
2
26
12
www.desatech.com
119588-01A
Parts List
Models
200C, RCP200V(A), SPC-200C, tC107 and TC200V(A)
This list contains replaceable parts used in your heater. When ordering parts, follow the
instructions listed under Replacement Parts on page 9 of this manual.
KEY
NO. PART NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Pilot Assembly
Hose/Regulator Assembly
Burner Ring Assembly
Ring Shield
Fuel Tube Assembly
Pilot Tube Assembly
Upper Shell
Orifice Adapter
Bracket, Pilot Mounting
Orifice, LP
Base
Cap
Thermocouple Clip Thin Hex Nut
Control Valve
Female Elbow Fitting, 1/4 FLR x 1/8 FPT
Female Elbow Fitting, 1/4 FLR x 1/4 FPT
Thermocouple
Lower Shell
Fitting, 1/4 FPT x 1/4 MPT
Ball Valve
Piezo Ignitor Kit
Valve Nut, 1/2-28
Female Elbow Fitting, 1/4 FPT x 3/8 FLR
Retaining Ring
Ignitor Electrode
Heat Shield
Pilot Orifice
Elbow Fitting, 1/8 FPT x 1/4 CPSN
113814-01
113835-01
113777-01
113778-01
113779-01
113780-01
114178-01
113782-01
113783-01
113816-01
**
113875-01
100898-01
113787-01
113788-01
113817-01
113790-01
113821-01
113812-01
113793-01
102445-01
113794-01
113795-01
113796-01
113797-01
113798-01
113820-01
113801-01
QTY.
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
3
1
1
1
1
1
PARTS AVAILABLE - NOT SHOWN
113809-01 Ball Valve Knob
113810-01 Ball Valve Knob Insert
117069-03 200,000 Btu Rating Decal
113808-01 Hang Tag (English)
113808-02 Hang Tag (Spanish)
113808-03 Hang Tag (French)
113805-01 Installation Decal (English)
113805-02 Installation Decal (Spanish)
113805-03 Installation Decal (French)
113802-19 Model Decal
**Not a field replaceable part
119588-01A
www.desatech.com
1
1
1
1
1
1
1
1
1
1
13
Warranty and Repair Service
KEEP THIS WARRANTY
Model
Serial No.
Date of Purchase
LIMITED WARRANTIES FOR NEW AND FACTORY
RECONDITIONED PRODUCTS
New Products: DESA Heating Products warrants this heater and any parts thereof, to be free of defects in materials and workmanship for one (1) year from the date of first purchase, when operated and
maintained in accordance with the manufacturer's instructions. These warranties are extended only to
the original retail purchaser, when proof of purchase is provided.
Factory Reconditioned Heaters: DESA Hea ing Products warrants this factory reconditioned heater and
any parts thereof, to be free of defects in materials and workmanship for thirty (30) days from the date of
first purchase, when operated and maintained in accordance with the manufacturer's instructions. These
warranties are extended only to the original retail purchaser, when proof of purchase is provided.
These warranties cover only the cost of parts and labor required to restore the product to proper operating condition. Transportation and incidental costs associated with warranty repairs are not reimbursable
under this warranty.
Warranty service is available only through authorized dealers and service centers.
This warranty does not cover defects resulting from misuse, abuse, negligence, accidents, lack of proper
maintenance, normal wear, alteration, modifica ion, tampering, contaminated fuels, repair using improper
parts or repair by anyone other than an authorized dealer or service center. Routine maintenance is the
responsibility of the owner.
THIS EXPRESS WARRANTY IS GIVEN IN LIEU OF ANY OTHER WARRANTY EITHER EXPRESSED
OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
DESA Heating Products assumes no responsibility for indirect, incidental or consequential damages.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations or exclusions may not apply to you. This limited warranty gives you specific legal rights and you
may also have other rights which vary from province to province.
WARRANTY SERVICE
Should your heater require service, return it to your nearest authorized service center. Proof of purchase
must be presented with the heater. The heater will be inspected. A defect may be caused by faulty materials
or workmanship. If so, DESA Heating Products will repair or replace the heater without charge.
REPAIR SERVICE
Return the heater to your nearest authorized service center. Each Service Center is independently owned
and operated. Repairs not covered by the warranty will be billed at standard prices. We reserve the right
to amend these specifications at any time without notice.
Illustrated parts lists can be obtained free of charge. Send a self-addressed stamped envelope to the
address listed below. List the heater model number and the date located in the lower right corner of this
page. A service manual may be purchased from the address listed below. Send a check or money order
for $5.00 (US) payable to DESA Heating Products.
When writing for informa ion regarding your heater, be sure to include the model number and serial number
as shown on the model plate.
2701 Industrial Drive
P.O. Box 90004
Bowling Green, KY 42102-9004
ATTN: Customer Service Department
82 Akron Road
Toronto, Ontario
M8W 1T2
119588-01
Rev. A
06/06
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement