iC5000 On-Chip Analyzer

iC5000 On-Chip Analyzer
_
V5.7
Hardware Reference
iC5000 On-Chip Analyzer
Thank you for purchasing this product from iSYSTEM. This product has been carefully crafted to satisfy your
needs. Should any questions arise, do not hesitate to contact your local distributor or iSYSTEM directly. Our
technical support personnel will be happy to answer all your technical support questions.
All information, including contact information, is available on our web site www.isystem.com. Feel free also to
explore our alternative products.
iSystem constantly yields for development and therefore certain pictures in this documentation may vary slightly
from the actual product you received. The differences should be minor, but should you find more serious
inconsistencies of the product with the documentation, please contact your local distributor for more
information.
This document and all documents accompanying it are copyrighted by iSYSTEM and all rights are reserved.
Duplication of these documents is allowed for personal use. For every other case a written consent from
iSYSTEM is required.
Copyright  2015 iSYSTEM, AG.
All rights reserved.
All trademarks are property of their respective owners.
www.isystem.com
 iSYSTEM, January 2015
1/64
iC5000 Base Unit
Ordering code
IC50000 or IC50000-1
The iC5000 Base Unit is a base platform connecting to the PC via the TCP/IP or USB 2.0 port. It is always used
in conjunction with the DTM and/or the I/O module.
The iC5000 Base Unit features 256MB of analyzer storage buffer.
There are three status LEDs on the iC5000 Base Unit. The status LEDs inform the user of the current status of
the emulation system. Their meaning is:

– When lit, the unit is turned on

R – When lit, the target application being controlled is running

F – When lit, the unit is free for communication, i.e. winIDEA can connect to it.
 iSYSTEM, January 2015
2/64
Powering the emulator
A round 3-pin power connector is located on the rear of the iC5000 base unit.
Power connector pinout, view from the rear of the Emulator
The iC5000 unit accepts a wide input voltage range from 10V to 24V DC, thus enabling the Emulator to work
also with a 12V or 24V car battery. Power consumption is up to 6W (iC5000 with Debug/Trace Module, and
cable adapter, without I/O module).
The necessary power supply (IC30000-PS) is delivered beside the iC5000 unit.
IC30000-PS
An optional 12V power supply for Car (cigarette lighter) plug can be ordered under the IC30000-PS-CAR12V
ordering code.
IC30000-PS-CAR12V
Note: Use only original iSYSTEM accessories for powering the iC5000. If you wish to use a power supply
different from the delivered one, please consult with iSYSTEM first.
Note: When powering the system, switch ON emulator before target; when shutting down the system, switch
OFF target before emulator!
 iSYSTEM, January 2015
3/64
iC5000 Debug/Trace Module (JTAG/BDM)
Ordering code
IC50020
iC5000 Base Unit in conjunction with the iC50020 Debug/Trace module is a universal on-chip emulation
platform. Additionally, a connecting cable (40-pin flat cable), a target specific cable adapter and architecture
specific license is required to debug the target based on a specific architecture.
Valid input voltage range for all debug signals is between 1.8 - 5.5V
Note: Typically, IC50000 and IC50020 module already come assembled together when delivered to the user.
The user only needs to connect a specific cable adapter via 40-pin flat cable, through which then the
development system connects to the target.
iC5000 development and test system including also an optional IO module
 iSYSTEM, January 2015
4/64
40-pin flat cable used to connect architecture specific debug cable adapters to the iC5000 Debug/Trace module.
16-bit Nexus (IC50152), 16-bit ETM (IC50115) and 10-pin Infineon DAP (IC50161) cable adapters come with
two flat cables (30-pin and 40-pin) pre-attached. With these, 40-pin flat cable, which is shipped next to the
Debug/Trace module (IC50020), is not required. Note that these debug cable adapters require iC5000
Debug/Trace module revision D or newer, and cannot be connected to the older revisions.
iC5000 I/O Module (IOM2)
Ordering code
IC50011

System Port: inter-emulator synchronization and trigger output, 100ohm series termination.

Digital inputs: 8 channels, 10kOhm input impedance, 5V tolerant, ESD protected.

Digital outputs: 8 channels, 100ohm output series termination, ESD protected.

Analog inputs: 2 channels, 8-bit ADCs, 1MOhm input impedance, range is ±5.0V with 1:1 probe, ±50V
with a 10:1 probe, 3ns acquisition time.
Power measurement probe uses these two inputs for power measurement. (Available on rev. C and later)

Analog outputs: 2 channels, 8-bit DACs, ±4.5V bipolar output, ±7mA drive, 100ohm output resistance.

Optional 10MHz temperature compensated precision oscillator TCXO for a high accuracy long duration
trace/analyzer session measurements.
All digital signals are 3.3V LVTTL compatible and are ESD protected.
All analog signals have a Schottky diode over- / undervoltage protection, except the Current Sense signals.
The maximum voltage on the Current Sense probe is 60V.
Nominal sampling rate is 1MSPS.
 iSYSTEM, January 2015
5/64
Connectors
iC5000 I/O Module Connectors’ Pinout

10-pin header for the System Port.

16-pin header for 8 digital inputs.

16-pin header for 8 digital outputs.

10-pin header for 2 analog outputs.

2 BNC connectors for 2 analog inputs.

10-pin header for Power Measurement Port (rev. C and later).
All connectors, except the BNCs, are standard Berg 2.54mm / 100mils raster.
For analog inputs, standard scope probes can be used.
For more details on I/O module and its use, refer to a separate standalone document titled I/O Module user’s
manual.
 iSYSTEM, January 2015
6/64
Using grounding wire
In case of the on-chip emulation, it has been proven that a development tool can be damaged at the moment
when the emulator's debug connector is plugged into the target system when neither the target nor the emulator
are powered up yet. At this point in time, there could be ground potential difference between the emulator and
the target way over 1000V. Such voltage difference is then discharged over the emulator and the target, which
can destroy electronic components of the emulator and/or the target.
The voltage difference can be introduced by:

power supply (target, emulator), which does not have the power outlet ground connected with the power
supply ground.

power outlets which have different ground potentials

PC, when iC5000 connects to the PC through the USB port
Connecting a dedicated grounding wire, which is shipped with the iC5000 unit, between the iC5000 system and
the target before the target debug cable adapter is connected to the target, makes the complete development
system even more robust and resistant to the mentioned electrical discharge problem - despite the fact the iC5000
development system features already a high quality protection on all connecting signals by default.
iC5000 with the grounding wire and the ground pin in the left bottom corner
 iSYSTEM, January 2015
7/64
The grounding wire connecting the target and iC5000
Licenses
iC5000 introduces a new licensing model. As with all iSYSTEM tools, winIDEA license is required. Valid
winIDEA license also includes iSYSTEM technical support service, and can be requested either by phone or by
e-mail [email protected]
Besides winIDEA license, at least one CPU architecture license is required in order to connect to the target
microcontroller via debug interface. Advanced functionalities such as trace, profiling and code coverage become
available via trace license. Make sure that the target debug connector to which ic5000 system connects, exposes
microcontroller trace port (ETM, Nexus …) when trace functionality is required.
iSYSTEM development tools feature a hardware based license scheme, which saves costs comparing to per-seat
based licenses. All licenses are kept in the iC5000 development system, which conveniently allows moving
iC5000 unit from one development seat to another.
When new iC5000 system is shipped from iSYSTEM, CPU architecture and trace licenses are preprogrammed
by the iSYSTEM test department. With such a new system, only winIDEA license needs to be requested from
iSYSTEM after receiving the iC5000 system. Additional CPU architecture license, which are purchased later,
must be programmed by the user.
Below picture shows the sticker, which can be found on iC5000 system, identifying which CPU architecture
licenses were preprogrammed by the iSYSTEM test department. Below picture shows preprogrammed CortexM3 and MPC56xx licenses.
 iSYSTEM, January 2015
8/64
Communication
iC5000 supports two types of communication: 10/100M Ethernet and USB 1.1/2.0. It is recommended to use
USB2.0 interface since it provides the fastest transfer from the iC5000 development system to the PC where
winIDEA IDE runs. This will guarantee a maximum performance of the iC5000 development system.
Specify the communication port through which the iC5000 unit connects to the PC in the
Hardware/Hardware/Communication tab.
Hardware Configuration dialog, Communication page

Universal Serial Bus (USB) - select when the Emulator is attached to the PC's USB port. The Emulator is
selected in the Device pull-down menu. When the Emulator is connected to the USB port of a computer for
the first time, Windows will detect a new device and prompt you for the driver for it. Specify the path to the
USB directory in the winIDEA installation directory. If only one emulator is connected to a PC via USB
then Device combo box can be left empty (recommended). In this case if you exchange the emulator
with another one, you don’t have to change communication settings.

TCP/IP – This option sets the TCP/IP properties of the iC5000. See ‘Setting up TCP/IP communication’
section for more details on TCP/IP setup.
Use the 'Test' button to test the communication settings.
Communication test window
 iSYSTEM, January 2015
9/64
Setting up TCP/IP communication
If the Emulator is connected using the Ethernet, its TCP/IP settings must be configured on both sides: the
Emulator and in winIDEA.
More information on configuring the Emulator and winIDEA can be found in the Hardware User’s Guide.
First step: Configuring the Emulator
The Emulator must be connected using an alternate option – either through the serial port, through the parallel
port or through USB. The connection must be set up in the ‘Hardware/Communication’ tab. Then, select the
‘Hardware/Hardware Type’ tab and click on the ‘System Configuration…’ button.
System configuration options
The TCP/IP settings can be obtained from the DHCP server on the network. If such a server is not available, the
settings can be set manually. In this case, in the TCP/IP Configuration window, the IP Address, the Subnet Mask
and the TCP Port must be specified. The default gateway address must be specified, if the Emulator is used via a
gateway. The IP Address, available for the Emulator to use, the Subnet Mask and the default gateway, if needed,
are usually defined by your network administrator. The TCP Port can be any port between 1024 and 65535,
which is not already used. By default, the TCP port 5313 is used. For the information, if this port address could
cause any conflicts and for an alternative port address, also contact your network administrator. When the correct
settings are entered, click on the ‘Apply changes’ button. This writes the changes to the Emulator.
If you want winIDEA to use these settings, press the “Use this communication setting” button. Then, close the
System configuration window.
The Emulator must be switched off and then on again in order for changes to take effect.
Emulator’s MAC address is written on the same sticker where you will also find device serial number as it is
shown on the next picture.
 iSYSTEM, January 2015
10/64
Second step: Configuring
There are two ways of configuring TCP/IP in winIDEA: manually or by automatic discovery.

Manual Configuration
Select the Hardware/Communication tab.
Hardware/Communication tab
If the “Use this communication setting” button was used when configuring the Emulator, these settings should
already be set as required. If this option was not used, select the TCP/IP button and enter the IP Address and the
TCP Port, as entered above into the Emulator. Connect the Emulator to the Ethernet, if not already connected,
and click on the ‘Test’ button. The communication should be up and running.

Configuration with Automatic Discovery
Select the Hardware/Communication tab.
Display of discovered emulators
First, select ‘TCP/IP’ type of communication. Then select the ‘Use global discovery on UDP port 58371’ and
press the Refresh button.
 iSYSTEM, January 2015
11/64
In the pull-down window all emulators found on the network will be shown. The correct emulator can be
identified by its serial number. Select the emulator and press the ‘Test’ button to ensure the communication is
possible.
To be able to easier identify your own emulator, you can specify an unique port number in the first step (for
example, as shown above, 23456; the number can be any number between 1024 and 65535, that is not already
used on your network for other purposes – note that on the other hand more emulators can have the same port
number), uncheck the ‘Use global discovery’ option, enter the port number, if the correct one is not entered
already, and press the refresh button. Now, only the emulators on the network that use this port will be shown.
Troubleshooting TCP/IP
If the communication test fails, there could be a problem with the IP Address, the Subnet Mask, the Default
gateway address or the TCP Port.
First, make sure the Subnet Mask is correct. The subnet mask should be the same in the TCP/IP configuration of
your computer and in the Emulator.
To find out the TCP/IP settings of your computer, open the command prompt and type ‘ipconfig’. The computer
will return something like this:
Ethernet adapter Local Area
Connection-specific
IP Address. . . . .
Subnet Mask . . . .
Default Gateway . .
Connection:
DNS Suffix
. . . . . .
. . . . . .
. . . . . .
.
.
.
.
:
: 210.121.92.121
: 255.255.255.0
: 210.121.92.65
Enter the same Subnet Mask and the Default Gateway data into Emulator.
Next, make sure, the IP Address is not already used by any other device. The easiest way to do that is to
disconnect the Emulator from the Ethernet, open a command prompt and type in ‘ping <ip_address>’ where
<ip_address> is the IP Address selected when configuring the Emulator, in the above example you would type in
‘ping 210.121.92.92’ (without quotes). The result should be ‘Request timed out…’. If the result of the command
is anything else (like ‘Reply from…’), the IP is already taken and you should choose another one. If the result is
correct, type in ‘ping <ip_address> -w 500 –t’, in the above example this would mean ‘ping 210.121.92.92 –w
500 –t’ . This command pings the IP address every 500 milliseconds until you stop it with Control+C. You
should constantly receive the information ‘Request timed out’. Then, while the ping command is running,
connect the Emulator and turn it on. Now, in a few moments, a ping reply should occur, in the form of ‘Reply
from <ip_address>’… If this is not the case, the IP was set wrong. Try setting the IP again or select another one.
If this is the case and the Emulator still cannot communicate with winIDEA, the TCP Port setting is wrong.
Please select another port, set it up in the Emulator and in winIDEA and try again. When the ping is not more
required, stop it using the keyboard shortcut Control+C.
If more Emulators are connected to the Ethernet and have the same IP set, only one will be active. Every
Emulator must have a unique IP.
Troubleshooting USB
During winIDEA installation USB driver is also installed. Very rarely after you power on the emulator which
you connected to PC Windows show errors:
1. USB device not recognized
2. Cannot Install this Hardware.
If first error is displayed you should:
 Check cable or use another USB cable.
 Connect emulator to another USB port
 Connect emulator to a different USB port. The one that resides on a PCI or PCIe card.
 Connect emulator to a PC via powered USB switch. In case a PC (usually a laptop) cannot provide
enough power over USB port.
If second error is displayed or the above suggestions for the first error don’t solve the problem you should
reinstall the driver. Use the following procedure.
In Windows click on the start menu and select run, then type %ALLUSERSPROFILE% and press OK.
 iSYSTEM, January 2015
12/64
Run Dialog which shows how to find folder with iSystem USB drivers
Windows explorer window will be shown. Open isystem\drivers folder and you should see the same files as on
the below screenshot.
iSystem USB drivers shown in Windows explorer
Power down the emulator and double click on the InstallDriver.exe file which first installs new driver and then
uninstalls older driver and removes registry entries which point to older driver.
If Windows still shows “Cannot install this Hardware” dialog then manual driver uninstall procedure should be
performed.
 iSYSTEM, January 2015
13/64
Cannot Install this Hardware error message
Manual uninstallation of drivers
To manually uninstall driver you should first identify the files you must remove from the computer.
From the Windows start menu select Run and type regedit and press the OK button.
In regedit locate the key HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class
Press CTRL + F and enter iSystem in the search dialog and press OK.
Regedit window

Regedit should display a key with several strings as shown above. Under this key there are also subkeys
represented by numbers. Click on such a key and inside locate a string named InfPath which points to
an INF file. Locate this INF file in c:\Windows\Inf folder and delete it. Repeat the procedure for all
different INF files found in registry.
 iSYSTEM, January 2015
14/64
Regedit window showing a key which points to an old USB driver



Then delete the main key (with all subkeys) which holds the data of all enumerated iSystem devices. In
example shown above the key is {00294380-BBA1-11D5-A7B8-0000F81A2088}.
At the end remove the folder where winIDEA installs the driver, for example:
C:\Documents and Settings\All Users\isystem\drivers
The folder path is different on windows 7 and Vista.
Now, restart the PC and again install the iSystemDriverPack which you can find here:
http://www.isystem.com/downloads/winIDEA/driver/isystem_usb_driver_setup.exe
The above procedure can be executed only if you have administrator rights.
 iSYSTEM, January 2015
15/64
Trace Line Calibration
Majority of the modern embedded microcontrollers providing trace functionality, implements a so called
message based trace port, where an individual trace message is broadcasted off the microcontroller through a
relatively narrow physical trace port in multiple CPU cycles, at frequencies, which can be well over 100 MHz.
Typically, the trace port is combined from trace data lines and a trace clock line, which is used to sample trace
data lines on rising, falling or both edges (depending on the individual implementation).
At lower frequencies and good signal integrity we can consider the clock and data lines as pure digital signals,
which are correctly phase aligned. As such, the external trace tool can capture them accurately without any
problems.
Nowadays, capturing of the valid trace data becomes more and more challenging due to the various signal
integrity issues (noise, skew, crosstalk, reflections, ground bounce…), which are introduced either due to the
high frequency trace clock & data, due to the bad target PCB design or a combination of both. IC5000 has the
ability to compensate for these issues via Trace Line Calibration functionality, which allows shifting threshold
voltage and clock phase at the capture time of the trace data. When Trace Line Calibration is performed, it auto
scans over these two dimensions and searches for valid and invalid settings and finds an optimum data eye.
Example
Let’s assume we have a Cortex-M3 based NXP LPC1768 microcontroller running at 95 MHz. At this frequency,
some of the signal integrity issues will show up for sure. After the debug download, the application should be
run. Next, the “Start” button in the “Hardware/Tools/ Trace Line Calibration” should be pressed, which starts the
auto-scan. After a couple of seconds, the result of the scan is collected and recommended “Vref” and “Phase“
values are provided. Typically, the user just needs to press the “->” button to use the recommended values (or, if
desired, enter them manually) and finally use the Apply button.
Configuration part of the Trace Line Calibration dialog
Newly applied values are stored upon Save Workspace and also used on the next debug download.
The following picture shows the result of the Trace Line Calibration and the corresponding timing view of
signals on the trace port.
 iSYSTEM, January 2015
16/64
Good signal integrity at lower frequency with large
“Data eyes”
Trace Line Calibration window – scan has been
performed and applied.
X
.
R
o
invalid area
valid area
recommended
currently used
 iSYSTEM, January 2015
Higher frequency: Valid “Data eyes” shown on
upper data signal and how the clock (lower) must be
delayed.
17/64
Trace Port PCB Design Guidelines
This section contains some guidelines, which should be considered during the target PCB design to ensure the
correct operation of the trace port (ETM, Nexus,…) and the external trace tool (iC5000, iTRACE GT). Note that
the quality and timing of the trace port signals to the external trace tool are critical for correct and reliable trace
operation.

All trace port lines on the PCB should be as short as possible (max ~2,5 cm),

Traces should run on the same layer, or layers with the same impedance.

Preferred layer impedance is 50 Ohm.

Connector’s ground pins should be connected directly to PCB’s GND plane.

Trace clock should be serially terminated by 47 Ohm resistor as close as possible to the driver. The value of
the resistor may be changed depending on driver characteristics.

Trace clock should be clean of crosstalk – if possible with double distance to closest nets.

Trace clock should have only point-to-point connection – any stubs should be avoided.

It is strongly recommended also for other (data) lines to be point-to-point only. If any stubs are needed, they
should be as short as possible, when longer are required, there should be a possibility to optionally
disconnect them (e.g. by jumpers).

Trace port data bus inner crosstalk is not so important, but it is critical to isolate the whole bus from other
signals (including from the trace port clock).
The following examples show, how the length of the trace lines is reflected in signal integrity and consequently
in functionality. One of typical evaluation boards was used, where the CPU is located on the upper piggyback
board, which fits to the lower, larger measurement board.
Trace lines with short stubs
Trace Line Calibration result
Measured by oscilloscope
Trace lines with longer stubs (over connector to other board)
 iSYSTEM, January 2015
18/64
Trace Line Calibration result
Measured by oscilloscope
Emulation Notes
Above message can occur when using trace. It indicates that the DDR (trace storage RAM) input FIFO, which
accepts trace data from the system domain, has overflowed, and some portion of the trace data will be missing. It
doesn’t mean any hardware failure. Possible solutions:

lower the target CPU clock

increase Nexus clock divider, which yields lower Nexus clock, but at the same time Nexus is more
prone to overflows then

changing the trace port width e.g. from 16 bit to 12 bit or from 12 bit to 4 bit reduces the Nexus
information bandwidth. Note that possible port size varies depending on the target CPU.

IC50000-1 (ordering code) has higher trace storage bandwidth than IC50000.
 iSYSTEM, January 2015
19/64
Debug Cable Adapters
Various cable adapters are available depending on the specific target architecture and the target debug connector.
They are used to connect iC5000 development system to the target.
Ordering code
IC50111
Adapter
20-pin 2.54mm Cortex Debug Cable Adapter &
20-pin 2.54mm ARM Cable Adapter
IC50112
14-pin 2.54mm ARM Cable Adapter
IC50113-AMP
20-pin 1.27mm AMP Cortex Debug Cable Adapter
IC50114
Mictor 38-pin ARM ETM 8-bit Cable Adapter
IC50115
Mictor 38-pin ARM ETM 16-bit Cable Adapter
IC50116
10-pin 1.27mm Cortex Debug Cable Adapter
IC50118
20-pin 1.27mm Cortex Debug Cable Adapter
IC50130
26-pin 2.54 mm ColdFire Cable Adapter
IC50140
6-pin 2.54mm BDM Cable Adapter
IC50141
6-pin 2.54mm S12Z Cable Adapter
IC50150
14-pin 2.54mm MPC5xxx Cable Adapter
IC50151
Mictor 38-pin MPC5xxx Nexus 8-bit Cable Adapter
IC50152
Mictor 38-pin MPC5xxx Nexus 16-bit Cable Adapter
IC50152-12
IC50153
16-pin 2.54mm Freescale COP Cable Adapter
IC50154
51-pin GLENAIR Cable Adapter
IC50155
Mictor 38-pin PPC4xx RISCTrace Cable Adapter
IC50160
16-pin 2.54mm Infineon JTAG Cable Adapter
IC50160-ECU14
10-pin 1.27mm Tricore ECU14 Cable Adapter
IC50160-MEDC17
10-pin 1.27mm Tricore MEDC17 Cable Adapter
IC50162
6-pin 2.54mm Infineon I2C Cable Adapter
IC50163
10-pin 1.27mm Infineon DAP2 Wide Cable Adapter
IC50170
16-pin 2.54mm Renesas 78K0R Serial Cable Adapter
IC50174
10-pin 2.54mm Renesas 78K0 Serial Cable Adapter
IC50175
14-pin 2.54mm Renesas RL78 Serial Cable Adapter
IC50171
20-pin 2.54mm Renesas V850/RH850 Cable Adapter
IC50172
26-pin KEL Renesas V850 Cable Adapter
IC50173
14-pin 2.54mm Renesas SuperH Cable Adapter
IC50190
4-pin ERNI ST STM8 Cable Adapter
IC50176
14-pin 2.54mm Renesas RH850 Cable Adapter
IC50177
Mictor 38-pin Renesas RH850 Nexus 16-bit Cable Adapter
 iSYSTEM, January 2015
20/64
Signal direction definition used throughout this document:
O
I
- output from the debugger to the target microcontroller
- input to the debugger from the target microcontroller
 20-pin 2.54mm Cortex Debug Cable Adapter
This adapter is delivered under the IC50111 ordering code. Note that another adapter comes along under this
ordering code and that is 20-pin 2.54mm ARM Cable Adapter.
Ordering code
IC50111
This adapter is used to connect the iC5000 development system to Cortex-M (M0, M0+, M1, M3, M4) based
target. It connects to Debug/Trace module (IC50020) on one side and to the target debug connector on the other
side. It can be used for targets featuring 20-pin 2.54 pitch target debug connector with Cortex-M pinout.
The following pinout is valid on the target side:
Signal Signal description Signal
direction
I
Reference voltage VTref
Ground
GND
Ground
GND
Ground
GND
Ground
GND
Ground
GND
Ground
GND
Ground
GND
Ground
GND
Ground
GND
Pin
Pin
Signal
Signal description
1
3
5
7
9
11
13
15
17
19
2
4
6
8
10
12
14
16
18
20
SWDIO/TMS
SWCLK/TCK
SWO/TDO
NC/TDI
nSRST
TRCLK
TRD0
TRD1
TRD2
TRD3
SWD/JTAG
SWD/JTAG
SWD/JTAG
SWD/JTAG
System Reset
Trace Clock
Trace Data 0
Trace Data 1
Trace Data 2
Trace Data 3
Signal
direction
I/O
O
I
O
I/O
I
I
I
I
I
20-pin Cortex-M pinout
Note: 20-pin 2.54mm Cortex-M Cable Adapter features resettable fuses on pins 1, 2, 4, 6, 8 and 10. These
protect debug signals against overcurrent. These fuses cycle back to a conductive state after the excessive current
fades away.
The adapter connects to the target via a 20-pin 2.54 mm connector (for example Yamaichi: FAS-2001-2101-20BF). A target should feature a matching part (for example WÜRTH ELEKTRONIK: 612 020 216 21).
 iSYSTEM, January 2015
21/64
 20-pin 2.54mm ARM Cable Adapter
This adapter is delivered under the IC50111 ordering code. Note that another adapter comes along under this
ordering code and that is 20-pin 2.54mm Cortex-M Cable Adapter.
Ordering code
IC50111
This adapter is used to connect the iC5000 development system to Cortex-A, Cortex-R, or ARM7, ARM9 based
target. It connects to Debug/Trace module (IC50020) on one side and to the target debug connector on the other
side. It can be used for targets featuring 20-pin 2.54 pitch target debug connector with ARM pinout.
The following pinout is valid on the target side:
Signal
direction
I
O
O
O
O
I
I
I/O
O
I
Signal description
Signal
Reference voltage
Debug JTAG
Debug JTAG
Debug JTAG
Debug JTAG
Return TCK
Debug JTAG
System Reset
Debug request
Debug Acknowledge
VTref
nTRST
TDI
TMS
TCK
RTCK
TDO
nSRST
DBGRQ
DBACK
Pin Pin Signal
1
3
5
7
9
11
13
15
17
19
2
4
6
8
10
12
14
16
18
20
NC
GND
GND
GND
GND
GND
GND
GND
GND
GND
Signal description
Signal
direction
Not Connected
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
20-pin ARM pinout
Note: 20-pin 2.54mm ARM Cable Adapter features resettable fuses on all pins except for pin 11 and 19. These
fuses protect debug signals against overcurrent and cycle back to a conductive state after the excessive current
fades away.
The adapter connects to the target via a 20-pin 2.54 mm connector (for example Yamaichi: FAS-2001-2101-20BF). A target should feature a matching part (for example WÜRTH ELEKTRONIK: 612 020 216 21).
 iSYSTEM, January 2015
22/64
Texas Instruments Microcontrollers
Note that targets based on Texas Instruments (TI) ARM microcontroller may feature Texas Instruments ARM
14-pin target debug connector with TI proprietary pinout.
A dedicated adapter is available for Texas Instruments ARM 14-pin pinout and can be ordered separately under
IAPIN20ARM14TI ordering code. Make sure you don’t mix up Texas Instruments pinout with standard 14-pin
2.54mm ARM pinout (cable adapter IC50112).
Double check the pinout of the target debugs connector with the iC5000 cable adapter pinout before connecting
iC5000 to the target for the first time.
Ordering code
IAPIN20ARM14TI
With this adapter, the following pinout is valid on the target side:
Signal
direction
Output
Output
Input
Input
Input
Output
Input
Signal description
Signal
Pin Pin Signal
Standard JTAG
Standard JTAG
Reference voltage
Standard JTAG
Return TCK
Standard JTAG
Debug Acknowledge
TMS
TDI
VTref
TDO
RTCK
TCK
BERR
1
3
5
7
9
11
13
2 nTRST
4
GND
6
NC
8
GND
10 GND
12 GND
14 nSRST
Signal description
Standard JTAG
Ground
Not connected
Ground
Ground
Ground
System Reset
Signal
direction
Output
In/Out
ARM7 14-pin TI target connector
A jumper is present on the adapter. If this jumper is set, the SYSTEM RESET line is connected to pin 14 on the
target side. If SYSTEM RESET is not needed, then this jumper should be removed.
Note: this adapter can only be used with 20-pin 2.54mm ARM Cable Adapter
The adapter connects to the target via a 14-pin 2.54 mm connector (for example Yamaichi: FAS-1401-2101-20BF). A target should feature a matching part (for example WÜRTH ELEKTRONIK: 612 014 216 21).
 iSYSTEM, January 2015
23/64
 14-pin 2.54mm ARM Cable Adapter
Ordering code
IC50112
IC50112 ARM Cable Adapter is used to connect the iC5000 development system to Cortex-A, Cortex-R, or
ARM7, ARM9 based target. It connects to Debug/Trace module (IC50020) on one side and to the target debug
connector on the other side. It can be used for targets featuring 14-pin 2.54 pitch target debug connector with
ARM pinout.
The following pinout is valid on the target side:
Signal
direction
O
O
O
O
I
I
Signal description
Signal
Pin Pin Signal
Not Connected
Debug JTAG
Debug JTAG
Debug JTAG
Debug JTAG
Debug JTAG
Reference voltage
NC
nTRST
TDI
TMS
TCK
TDO
VTref
1
3
5
7
9
11
13
2 GND
4 GND
6 GND
8 GND
10 GND
12 nSRST
14 GND
Signal description
Ground
Ground
Ground
Ground
Ground
System Reset
Ground
Signal
direction
I/O
14-pin ARM pinout
Note: 14-pin 2.54mm ARM Cable Adapter features resettable fuses on all pins. These fuses protect debug
signals against overcurrent and cycle back to a conductive state after the excessive current fades away.
The adapter connects to the target via a 14-pin 2.54 mm connector (for example Yamaichi: FAS-1401-2101-20BF). A target should feature a matching part (for example WÜRTH ELEKTRONIK: 612 014 216 21).
 iSYSTEM, January 2015
24/64
 20-pin 1.27mm Cortex Debug Cable Adapter
Ordering code
IC50113
Note: This product is obsolete and is fully replaced with IC50118
IC50113 Cortex-M Adapter Board is used to connect the iC5000 development system to Cortex-M (M1, M3,
M4) based target. It connects to Debug/Trace module (IC50020) on one side and to the target debug connector
on the other side. It can be used for targets featuring 20-pin 1.27mm pitch target debug connector with Cortex-M
pinout.
The following pinout is valid on the target side:
Signal Signal description Signal
direction
I
Reference voltage VTref
Ground
GND
Ground
GND
Ground
GND
Ground
GND
Ground
GND
Ground
GND
Ground
GND
Ground
GND
Ground
GND
Pin
Pin
Signal
Signal description
1
3
5
7
9
11
13
15
17
19
2
4
6
8
10
12
14
16
18
20
SWDIO/TMS
SWCLK/TCK
SWO/TDO
NC/TDI
nSRST
TRCLK
TRD0
TRD1
TRD2
TRD3
SWD/JTAG
SWD/JTAG
SWD/JTAG
SWD/JTAG
System Reset
Trace Clock
Trace Data 0
Trace Data 1
Trace Data 2
Trace Data 3
Signal
direction
I/O
O
I
O
I/O
I
I
I
I
I
20-pin Cortex-M pinout
Note: 20-pin 1.27mm Cortex-M Cable Adapter features resettable fuses on pins 1, 2, 4, 6, 8 and 10. These
protect debug signals against overcurrent and cycle back to a conductive state after the excessive current fades
away. Signals on pins 12, 14, 16, 18 and 20 are protected via 47 ohm serial resistors.
The adapter connects to the target via a 20-pin 1.27mm connector (for example SAMTEC: FFSD-10-01-N). A
target should feature a matching part (for example SAMTEC: FTSH-110-01-F-DV-K).
 iSYSTEM, January 2015
25/64
 20-pin 1.27mm AMP Cortex Debug Cable Adapter
Ordering code
IC50113-AMP
IC50113-AMP Cortex-M Cable Adapter is used to connect the iC5000 development system to Cortex-M (M1,
M3, M4) based target. It connects to Debug/Trace module (IC50020) on one side and to the target debug
connector on the other side. It can be used for targets featuring 20-pin 1.27mm AMPMODU target debug
connector with Cortex-M pinout.
The following pinout is valid on the target side:
Signal Signal description
direction
I
Reference voltage
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Signal
Pin Pin
VTref
GND
GND
GND
GND
GND
GND
GND
GND
GND
1
3
5
7
9
11
13
15
17
19
2
4
6
8
10
12
14
16
18
20
Signal
Signal description
SWDIO/TMS
SWCLK/TCK
SWO/TDO
NC/TDI
nSRST
TRCLK
TRD0
TRD1
TRD2
TRD3
SWD/JTAG
SWD/JTAG
SWD/JTAG
SWD/JTAG
System Reset
Trace Clock
Trace Data 0
Trace Data 1
Trace Data 2
Trace Data 3
Signal
direction
I/O
O
I
O
I/O
I
I
I
I
I
20-pin Cortex-M pinout
Note: 20-pin 1.27mm AMPMODU Cortex-M Cable Adapter features resettable fuses on pins 1, 2, 4, 6, 8 and 10.
These protect debug signals against overcurrent and cycle back to a conductive state after the excessive current
fades away. Signals on pins 12, 14, 16, 18 and 20 are protected via 47 ohm serial resistors.
The adapter connects to the target via a 20 -pin AMP connector (for example TE connectivity, part number 1111196-8). A target should feature a matching part (for example TE connectivity part number 5-104549-2 in
SMT technology).
 iSYSTEM, January 2015
26/64
 Mictor 38-pin ARM ETM 8-bit Cable Adapter
Ordering code
IC50114
This adapter is used to connect the iC5000 development system to ARM7/ARM9 based target. It connects to
Debug/Trace module (IC50020) on one side and to the target debug connector on the other side. It can be used
for targets featuring Mictor 38-pin target debug connector with ARM7/ARM9 ETM pinout.
Only 4 or 8-bit ETM port width (physical port size) is supported with this adapter. However, it can be also used
for ETM trace on targets where physically more than 8 ETM data lines are connected to the target debug
connector by configuring the on-chip ETM module for operation with 8 or less data lines (‘Hardware/CPU
Setup/ETM tab). Note that ETM port bandwidth proportionally drops off when less ETM data lines are used and
trace overflows are more likely to occur. If maximum bandwidth is needed, use IC50115, ARM ETM 16-bit
cable adapter.
The following pinout is valid on the target side:
Signal direction
O
I
O
O
O
O
Signal
NC
NC
NC
NC
nSRST
TDO
NC
TCK
TMS
TDI
nTRST
NC
NC
NC
NC
NC
NC
NC
NC
Pin
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
Pin
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
Signal
NC
NC
TRACECLK
NC
NC
VTref
NC
TRACEPKT[7]
TRACEPKT[6]
TRACEPKT[5]
TRACEPKT[4]
TRACEPKT[3]
TRACEPKT[2]
TRACEPKT[1]
TRACEPKT[0]
TRACESYNC
PIPESTAT[2]
PIPESTAT[1]
PIPESTAT[0]
Signal direction
I
I
I
I
I
I
I
I
I
I
I
I
I
I
8-bit ARM ETM target pinout
Blue colored signals are required for trace.
Note: Mictor 38-pin ARM ETM Cable Adapter features resettable fuses on pins 9, 11, 12, 15, 17, 19 and 21.
These protect debug signals against overcurrent and cycle back to a conductive state after the excessive current
fades away. Signals on pins 6, 16, 18, 20, 22, 24, 26, 26, 28, 30, 32, 34, 36 and 38 are protected via 47 ohm
serial resistors.
The adapter connects to the target via a 38-pin Mictor connector (Tyco Electronics 5767055-1). A target should
feature a matching part (for example Tyco Electronics 5767081-1 in SMT technology).
 iSYSTEM, January 2015
27/64
 Mictor 38-pin ARM ETM 16-bit Cable Adapter
Ordering code
IC50115
Note: iC5000 Debug/Trace module (IC50020) revision D or newer is required to be able to connect and use this
adapter.
This adapter is used to connect the iC5000 development system to ARM7/ARM9 based target. It connects to
Debug/Trace module (IC50020) on one side and to the target debug connector on the other side. It can be used
for targets featuring Mictor 38-pin target debug connector with ARM7/ARM9 ETM pinout.
The same cable adapter covers ETMv1 and ETMv3 pinout. The following pinout is valid on the target side:
Signal direction
O
I
O
O
O
O
I
I
I
I
I
I
I
I
Signal
Pin
Pin
Signal
NC
NC
NC
NC
nSRST
TDO
NC
TCK
TMS
TDI
nTRST
TRACEPKT[15]
TRACEPKT[14]
TRACEPKT[13]
TRACEPKT[12]
TRACEPKT[11]
TRACEPKT[10]
TRACEPKT[9]
TRACEPKT[8]
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
NC
NC
TRACECLK
NC
NC
VTref
NC
TRACEPKT[7]
TRACEPKT[6]
TRACEPKT[5]
TRACEPKT[4]
TRACEPKT[3]
TRACEPKT[2]
TRACEPKT[1]
TRACEPKT[0]
TRACESYNC
PIPESTAT[2]
PIPESTAT[1]
PIPESTAT[0]
Signal direction
I
I
I
I
I
I
I
I
I
I
I
I
I
I
ETMv1 target pinout
Blue colored signals are required for trace.
 iSYSTEM, January 2015
28/64
Signal direction
O
I
O
O
O
O
I
I
I
I
I
I
I
I
Signal
Pin
Pin
Signal
NC
NC
GND
NC
nSRST
TDO
NC
TCK
TMS
TDI
nTRST
TRACEDATA15
TRACEDATA14
TRACEDATA13
TRACEDATA12
TRACEDATA11
TRACEDATA10
TRACEDATA9
TRACEDATA8
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
NC
NC
TRACECLK
NC
NC
VTref
NC
TRACEDATA7
TRACEDATA6
TRACEDATA5
TRACEDATA4
TRACEDATA3
TRACEDATA2
TRACEDATA1
GND
GND
VCC
TRACECTL
TRACEDATA0
Signal direction
I
I
I
I
I
I
I
I
I
I
I
I
I
I
ETMv3 target pinout
Blue colored signals are required for trace.
Note: Mictor 38-pin ARM ETM Cable Adapter features resettable fuses on pins 9, 11, 12, 15, 17, 19 and 21.
These protect debug signals against overcurrent and cycle back to a conductive state after the excessive current
fades away. Signals on pins 6, 16, 18, 20 and 22-38 are protected via 47 ohm serial resistors.
The adapter connects to the target via a 38-pin Mictor connector (Tyco Electronics 5767055-1). A target should
feature a matching part (for example Tyco Electronics 5767081-1 in SMT technology).
Texas Instruments TMS570 Microcontrollers
Targets based on Texas Instruments (TI) ARM microcontroller can feature MIPI 60-pin target debug connector
with Texas Instruments proprietary pinout instead of 38-pin Mictor. MIPI term stands for Mobile Industry
Processor Interface and is a standardized connector for debugging and tracing up to 40 data lines.
A dedicated adapter (converter) is available for Texas Instruments MIPI 60-pin pinout and can be ordered
separately under the IAMIC38MIPI60TMS570 ordering code.
Double check the pinout of the target debugs connector before connecting iC5000 to the target for the first time.
Ordering code
 iSYSTEM, January 2015
IAMIC38MIPI60TMS570
29/64
Note: This adapter is always used in conjunction with the IC50115 cable adapter.
iC5000 can trace up to 16 trace data lines. The target microcontroller has to be configured for 16-bit trace port
operation if the target features MIPI connector with 32 data trace lines connected.
iSYSTEM high-end iTRACE GT development platform can capture 32-bit data trace port too.
Note that signal naming in iSYSTEM documentation uses target signal names and not the ones from the MIPI
standard. Refer to ‘MIPI Alliance Recommendation for Debug and Trace Connectors’ and ‘ARM Target
Interface Connections’ documentation for more information about signal names and their functions.
With this adapter, the following pinout is valid on the target side:
Signal direction
Signal
Pin
Pin
Signal
Signal direction
I
O
O
O
O
VTref
TCK
TDI
RTCK
nTRST_PU
NC
TRACECLK
NC
TRACECTL
TRACEDATA0
TRACEDATA1
TRACEDATA2
TRACEDATA3
TRACEDATA4
TRACEDATA5
TRACEDATA6
TRACEDATA7
TRACEDATA8
TRACEDATA9
TRACEDATA10
TRACEDATA11
TRACEDATA12
TRACEDATA13
TRACEDATA14
TRACEDATA15
NC
NC
NC
GND
NC
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
TMS
TDO
nSRST
nTRST_PD
NC
NC
NC
GND
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
GND
NC
O
I
O
O
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
60-pin MIPI target connector
Blue colored signals are required for trace.
The adapter connects to the target via a 60-pin MIPI connector (for example SAMTEC: QTH-030-01-L-D-A). A
target should feature a matching part (for example SAMTEC: QSH-030-01-L-D-A).
 iSYSTEM, January 2015
30/64
 10-pin 1.27mm Cortex Debug Cable Adapter
Ordering code
IC50116
This adapter is used to connect the iC5000 development system to Cortex-M (M0, M0+, M1, M3, M4) based
target. It connects to Debug/Trace module (IC50020) on one side and to the target debug connector on the other
side. It can be used for targets featuring 10-pin 1.27mm pitch target debug connector with Cortex-M pinout.
The following pinout is valid on the target side:
Signal
Signal description
direction
I
Reference voltage
Ground
Ground
Ground
Ground
Signal
VTref
GND
GND
GND
GND
Pin Pin
1
3
5
7
9
2
4
6
8
10
Signal
Signal description
SWDIO/TMS
SWCLK/TCK
SWO/TDO
NC/TDI
nSRST
SWD/JTAG
SWD/JTAG
SWD/JTAG
SWD/JTAG
System Reset
Signal
direction
I/O
O
I
O
I/O
10-pin Cortex-M pinout
Note: 10-pin 1.27mm Cortex-M Cable Adapter features resettable fuses on pins 1, 2, 4, 6, 8 and 10. These fuses
protect debug signals against overcurrent and cycle back to a conductive state after the excessive current fades
away.
The adapter connects to the target via a 10-pin 1.27mm connector (for example SAMTEC: FFSD-05-01-N). A
target should feature a matching part (for example SAMTEC: SHF-105-01-L-D-TH).
 iSYSTEM, January 2015
31/64
 20-pin 1.27mm Cortex Debug Cable Adapter
Ordering code
IC50118
IC50118 Cortex-M Adapter Board is used to connect the iC5000 development system to Cortex-M (M1, M3,
M4) based target. It connects to Debug/Trace module (IC50020) on one side and to the target debug connector
on the other side. It can be used for targets featuring 20-pin 1.27mm pitch target debug connector with Cortex-M
pinout.
The following pinout is valid on the target side:
Signal Signal description
direction
I
Reference voltage
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Signal
VTref
GND
GND
GND
GND
NC_CAPGND
NC_CAPGND
GND
GND
GND
Pin Pin
1
3
5
7
9
11
13
15
17
19
2
4
6
8
10
12
14
16
18
20
Signal
Signal description
SWDIO/TMS
SWCLK/TCK
SWO/TDO
NC/TDI
nSRST
TRCLK
TRD0
TRD1
TRD2
TRD3
SWD/JTAG
SWD/JTAG
SWD/JTAG
SWD/JTAG
System Reset
Trace Clock
Trace Data 0
Trace Data 1
Trace Data 2
Trace Data 3
Signal
direction
I/O
O
I
O
I/O
I
I
I
I
I
20-pin Cortex-M pinout
Note: 20-pin 1.27mm Cortex-M Cable Adapter features resettable fuses on pins 1, 2, 4, 6, 8 and 10. These
protect debug signals against overcurrent and cycle back to a conductive state after the excessive current fades
away. Signals on pins 12, 14, 16, 18 and 20 are protected via 47 ohm serial resistors.
The adapter connects to the target via a 20-pin 1.27mm connector (for example SAMTEC: FFSD-10-01-N). A
target should feature a matching part (for example SAMTEC: FTSH-110-01-F-DV-K).
 iSYSTEM, January 2015
32/64
 26-pin 2.54 mm ColdFire Cable Adapter
Ordering code
IC50130
This adapter is used to connect the iC5000 development system to Freescale ColdFire based target. It connects
between the Debug/Trace module (IC50020) and the target debug connector. It can be used for targets featuring
26-pin 2.54mm pitch target debug connector with ColdFire pinout.
The following pinout is valid on the target side:
Signal direction
I
I
I
I
I
I
Signal
Developer Reserved
GND
GND
RESET
VDD_IO
GND
PSTDDATA6
PSTDDATA4
PSTDDATA2
PSTDDATA0
Motorola Reserved
GND
NC
Pin
1
3
5
7
9
11
13
15
17
19
21
23
25
Pin
2
4
6
8
10
12
14
16
18
20
22
24
26
Signal
~BKPT
DSCLK
Developer Reserved
DSI
DSO
PSTDDATA7
PSTDDATA5
PSTDDATA3
PSTDDATA1
GND
Motorola Reserved
PSTCLK
~TEA
Signal direction
O
O
O
I
I
I
I
I
I
O
ColdFire 26-pin target pinout
Note: 26-pin 2.54 mm ColdFire Cable Adapter features resettable fuses on pins 2, 4, 7, 8, 9, 10, 24 and 26. These
protect debug signals against overcurrent and cycle back to a conductive state after the excessive current fades
away. Signals on pins 1, 12-19 and 24 are protected via 47 ohm serial resistors.
The adapter connects to the target via a 26-pin 2.54 mm connector (for example Yamaichi: FAS-26-17). A target
should feature a matching part (for example WÜRTH ELEKTRONIK: 612 026 216 21).
 iSYSTEM, January 2015
33/64
 6-pin 2.54mm BDM Cable Adapter
Ordering code
IC50140
This adapter is used to connect the iC5000 development system to Freescale HCS08, HC12, HCS12, S12X or
ColdFire V1 based target. It connects to Debug/Trace module (IC50020) on one side and to the target debug
connector on the other side. It can be used for targets featuring 6-pin 2.54mm pitch target debug connector with
BDM pinout.
The following pinout is valid on the target side:
Signal
direction
I/O
Signal description
Signal
BGND
Not connected
Not connected
BGND
NC
NC
Pin Pin
1
3
5
2
4
6
Signal
Signal description
GND
RESET
VTref
Ground
System Reset
Reference voltage
Signal
direction
I/O
I
6-pin BDM pinout
Note: 6-pin BDM Cable Adapter features resettable fuses on pins 1, 2, 4 and 6. These fuses protect debug signals
against overcurrent and cycle back to a conductive state after the excessive current fades away.
The adapter connects to the target via a 6-pin 2.54 mm connector (for example FCI: 71600-006LF). A target
should feature a matching part (for example WÜRTH ELEKTRONIK: 612 006 216 21).
 iSYSTEM, January 2015
34/64
 6-pin 2.54mm S12Z Cable Adapter
Ordering code
IC50141
This adapter is used to connect the iC5000 development system to Freescale S12Z based target. It connects to
Debug/Trace module (IC50020) on one side and to the target debug connector on the other side. It can be used
for targets featuring 6-pin 2.54mm pitch target debug connector with S12Z BDM pinout.
The following pinout is valid on the target side:
Signal
direction
I/O
I
I
Signal description
Signal
BGND
data out
clock
BGND
PDO
PDOCLK
Pin Pin
1
3
5
2
4
6
Signal
Signal description
GND
RESET
VTref
Ground
System Reset
Reference voltage
Signal
direction
I/O
I
6-pin BDM pinout
Note: 6-pin BDM Cable Adapter features resettable fuses on pins 1, 2, 4 and 6. These fuses protect debug signals
against overcurrent and cycle back to a conductive state after the excessive current fades away. Signals on pins 3
and 5 are protected via 47 ohm serial resistors
The adapter connects to the target via a 6-pin 2.54 mm connector (for example FCI: 71600-006LF). A target
should feature a matching part (for example WÜRTH ELEKTRONIK: 612 006 216 21).
 iSYSTEM, January 2015
35/64
 14-pin 2.54mm MPC5xxx Cable Adapter
Ordering code
IC50150
This adapter is used to connect the iC5000 development system to Freescale MPC5xxx and ST SPC56 based
target via JTAG debug interface. It connects to Debug/Trace module (IC50020) on one side and to the target
debug connector on the other side. It can be used for targets featuring 14-pin 2.54mm pitch target debug
connector with MPC5xxx pinout.
The following pinout is valid on the target side:
Signal
direction
O
I
O
O
O
I
Signal description
Signal
Pin Pin
Standard JTAG
Standard JTAG
Standard JTAG
TDI
TDO
TCK
EVTIN
nSRST
VTref
NC
1
3
5
7
9
11
13
System Reset
Reference voltage
Not connected
Signal
Signal description
2
GND
Ground
4
GND
Ground
6
GND
Ground
8 PORST*
Power On Reset*
10
TMS
Standard JTAG
12
GND
Ground
14 JCOMP (optional) Standard JTAG
Signal
direction
O
O
O
14-pin MPC5xxx & SPC56 target pinout
Mandatory pins on the microcontroller side are GND, VDD, RESET, TMS, TDI, TDO and TCK.
*Note: Pin 8 (Power on reset) is supported with adapter revision C1 or newer.
JCOMP is an optional pin. Some microcontrollers don’t have this pin. Internally, this is actually JTAG TRST
which resets JTAG TAP state machine. Because JTAG TAP state machine can be reset also by TMS and TCK,
this pin is optional also for the debugger. If microcontroller has JCOMP pin but it is not connected to the target
debug connector then it must be set to non-active state in the target via a pull-up resistor. If not then JTAG TAP
state machine remains in reset and debugging is not possible.
14-pin 2.54mm MPC5xxx Cable Adapter features resettable fuses on all connected pins. These protect debug
signals against overcurrent and cycle back to a conductive state after the excessive current fades away.
Jumper J2 (EVTIN)
Note: Jumper J2 is not needed, and is not assembled in new adapters. It was introduced with rv: C1, previous
versions (rv: A1, A2, B1) do not have this jumper.
Under some circumstances it can happen that the debugger cannot find any absolute program counter message in
the analyzed Nexus trace block. Consequentially, trace reconstruction fails and errors or nothing gets displayed
in the trace window. To avoid such situations, the debugger can feed periodic signal to the EVTIN CPU pin
connecting to the on-chip Nexus engine, which then periodically generates and broadcasts program counter
synchronization messages.
In order to use this feature, jumper J2 must be bridged and the ‘Force periodic Nexus SYNC’ option in the
‘Hardware/emulation Options/CPU Setup/Nexus’ tab must be checked. Refer to iSYSTEM ‘Freescale MPC5xxx
& ST SPC56 Family On-Chip Emulation’ technical notes document for more details on the ‘Force periodic
Nexus SYNC’ option use.
Note that the EVTI (Nexus Event In) CPU pin may be shared with other CPU functionalities. For instance, on
MPC5516 the same pin can operate as GPIO, EBI read/write or EVTI. Whenever the CPU pin is configured and
used for EVTI alternate operation, J2 must not be populated in order to prevent electrical conflicts.
 iSYSTEM, January 2015
36/64
Note: In general there is no need to use ‘Force periodic Nexus SYNC’ functionality unless a specific application
code is traced, which does not generate messages containing absolute program counter information. As long as
the user has no problems with the trace use, it is recommended to keep jumper J2 disconnected.
The adapter connects to the target via a 14-pin 2.54 mm connector (for example Yamaichi: FAS-1401-2101-20BF). A target should feature a matching part (for example WÜRTH ELEKTRONIK: 612 014 216 21).
 iSYSTEM, January 2015
37/64
 Mictor 38-pin MPC5xxx Nexus 8-bit Cable Adapter
Ordering code
IC50151
This adapter is used to connect the iC5000 development system to Freescale MPC5xxx or ST SPC56 based
target via Nexus debug interface. It connects to Debug/Trace module (IC50020) on one side and to the target
debug connector on the other side. It can be used for targets featuring Mictor 38-pin target debug connector with
MPC5xxx Nexus pinout.
This adapter supports 2, 4 or 8-bit Nexus port width only. However, it can be also used for Nexus trace on
targets where physically more than 8 Nexus data (MDO) lines are connected to the target debug connector by
configuring on-chip Nexus module for operation with 8 or less data lines (where possible). For majority of
MPC5xxx microcontrollers, it’s possible to configure on-chip Nexus module to broadcast Nexus information
through variable amount of Nexus data (MDO) lines. For instance, MPC555x can be configured for 4 or 12-bit
Nexus port operation, MPC551x for 8 or 12 bit Nexus port operation, etc… Note that Nexus port bandwidth
proportionally drops off when less Nexus data (MDO) lines are used and trace overflows are more likely to
occur. If maximum bandwidth is needed, use IC50152, MPC5xxx Nexus 16-bit cable adapter.
Jumper J2 (EVTIN)
Under some circumstances it can happen that the debugger cannot find any absolute program counter message in
the analyzed Nexus trace block. Consequentially, trace reconstruction fails and errors or nothing gets displayed
in the trace window. To avoid such situations, the debugger can feed periodic signal to the EVTIN CPU pin
connecting to the on-chip Nexus engine, which then periodically generates and broadcasts program counter
synchronization messages.
In order to use this feature, jumper J2 must be bridged and the ‘Force periodic Nexus SYNC’ option in the
‘Hardware/emulation Options/CPU Setup/Nexus’ tab must be checked. Refer to iSYSTEM ‘Freescale MPC5xxx
& ST SPC56 Family On-Chip Emulation’ technical notes document for more details on the ‘Force periodic
Nexus SYNC’ option use.
Note that the EVTI (Nexus Event In) CPU pin may be shared with other CPU functionalities. For instance, on
MPC5516 the same pin can operate as GPIO, EBI read/write or EVTI. Whenever the CPU pin is configured and
used for EVTI alternate operation, J2 must not be populated in order to prevent electrical conflicts.
Note: In general there is no need to use ‘Force periodic Nexus SYNC’ functionality unless a specific application
code is traced, which does not generate messages containing absolute program counter information. As long as
the user has no problems with the trace use, it is recommended to keep jumper 2 disconnected.
Note: Jumper J2 was introduced with rv:B1, previous versions (rv: A1, A2) do not have this jumper.
 iSYSTEM, January 2015
38/64
The following pinout is valid on the target side:
Signal direction
O
I
O
O
O
O
Signal
NC
NC
NC
NC
RSTIN
TDO
NC
TCK
TMS
TDI
NTRST
NC
NC
NC
NC
NC
NC
NC
NC
Pin
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
Pin
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
Signal
NC
NC
NC
NC
EVTIN
VTREF
NC
MDO7
MDO6
MDO5
MDO4
MDO3
MDO2
MDO1
MDO0
EVTO
MCKO
MSEO1
MSEO0
Signal direction
O
I
I
I
I
I
I
I
I
I
I
I
I
I
MPC5xxx and SPC56 16-bit Nexus target pinout
Note: Mictor 38-pin MPC5xxx Nexus 8-bit Cable Adapter features resettable fuses on pins 9, 10, 11, 12, 15, 17,
19 and 21. These protect debug signals against overcurrent and cycle back to a conductive state after the
excessive current fades away. Signals on pins 16, 18, 20, 22, 24, 26, 28, 30, 32, 34, 36 and 38 are protected via
47 ohm serial resistors.
The adapter connects to the target via a 38-pin Mictor connector (Tyco Electronics 5767055-1). A target should
feature a matching part (for example Tyco Electronics 5767081-1 in SMT technology).
 iSYSTEM, January 2015
39/64
 Mictor 38-pin MPC5xxx Nexus 16-bit Cable Adapter
Ordering code
IC50152
IC50152-12
Note: iC5000 Debug/Trace module (IC50020) revision D or newer is required to be able to connect and use this
adapter.
This adapter is used to connect the iC5000 development system to Freescale MPC5xxx or ST SPC56 based
target via Nexus debug interface. It connects between the Debug/Trace module (IC50020) and the target debug
connector. It can be used for targets featuring Mictor 38-pin target debug connector with MPC5xxx Nexus
pinout.
IC50152 features a standard connection length (cca. 24 cm). An adapter with shorter cable length (12 cm) was
introduced (ordering code IC50152-12) for cases when standard length doesn’t work e.g. due to a badly designed
target PCB where reliable Nexus trace capture with the standard 24 cm cable cannot be achieved. In such cases,
shorter cable helps. In practice, IC50152-12 is sometimes used in conjunction with the MPC5646C (3M Bolero)
target device, which internally seems to lack from fast drivers on the Nexus signals.
Jumper J2 (EVTIN)
Under some circumstances it can happen that the debugger cannot find any absolute program counter message in
the analyzed Nexus trace block. Consequentially, trace reconstruction fails and errors or nothing gets displayed
in the trace window. To avoid such situations, the debugger can feed periodic signal to the EVTIN CPU pin
connecting to the on-chip Nexus engine, which then periodically generates and broadcasts program counter
synchronization messages.
In order to use this feature, jumper J2 must be bridged and the ‘Force periodic Nexus SYNC’ option in the
‘Hardware/emulation Options/CPU Setup/Nexus’ tab must be checked. Refer to iSYSTEM ‘Freescale MPC5xxx
& ST SPC56 Family On-Chip Emulation’ technical notes document for more details on the ‘Force periodic
Nexus SYNC’ option use.
Note that the EVTI (Nexus Event In) CPU pin may be shared with other CPU functionalities. For instance, on
MPC5516 the same pin can operate as GPIO, EBI read/write or EVTI. Whenever the CPU pin is configured and
used for EVTI alternate operation, J2 must not be populated in order to prevent electrical conflicts..
Note: In general there is no need to use ‘Force periodic Nexus SYNC’ functionality unless a specific application
code is traced, which does not generate messages containing absolute program counter information. As long as
the user has no problems with the trace use, it is recommended to keep jumper 2 disconnected.
Note: Jumper J2 was introduced with rv: N1, previous versions (rv: M1) do not have this jumper.
 iSYSTEM, January 2015
40/64
The following pinout is valid on the target side:
Signal direction
I
I
I
O
I
I
O
O
O
O
I
Signal
MDO12
MDO14
MDO9
NC
RSTIN
TDO
MDO10
TCK
TMS
TDI
NTRST
MDO11
NC
NC
NC
NC
NC
NC
NC
Pin
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
Pin
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
Signal
MDO13
MDO15
NC
MDO8
EVTIN
VTREF
NC
MDO7
MDO6
MDO5
MDO4
MDO3
MDO2
MDO1
MDO0
EVTO
MCKO
MSEO1
MSEO0
Signal direction
I
I
I
O
I
I
I
I
I
I
I
I
I
I
I
I
I
I
MPC5xxx and SPC56 16-bit Nexus target pinout
Note: Mictor 38-pin MPC5xxx Nexus 16-bit Cable Adapter features resettable fuses on pins 9, 10, 11, 12, 15,
17, 19 and 21. These protect debug signals against overcurrent and cycle back to a conductive state after the
excessive current fades away. Signals on pins 1, 2, 3, 4, 5, 8, 13, 14, 16, 18, 20, 22, 23, 24, 26, 28, 30, 32, 34, 36
and 38 are protected via 47 ohm serial resistors.
The adapter connects to the target via a 38-pin Mictor connector (Tyco Electronics 5767055-1). A target should
feature a matching part (for example Tyco Electronics 5767081-1 in the SMT technology).
Ordering code
IAMIC38SAM50MPC
IAMIC38SAM50MPC adapter
Some targets based on Freescale Qorivva Power Architecture or PX Series Power Architecture
microcontroller(s) (e.g. MPC5675K) can also feature a 50-pin Samtec ERF8-025 connector for the Nexus debug
interface instead of a popular 38-pin Mictor connector. In this case, the IAMIC38SAM50MPC adapter is
connected to the target first and then used in conjunction with Mictor 38-pin MPC5xxx Nexus 16-bit Cable
Adapter.
In practice, it has been noticed that 50-pin Samtec target connector does not provide good mechanical stability in
one direction which as a result can also yield electrically unreliable connection. Special care must be taken when
connecting iC5000 to the target Samtec connector to minimize potential connection problems. Note that no
problems have been detected or reported in conjunction with the Mictor connector.
 iSYSTEM, January 2015
41/64
The following pinout is valid on the target side:
Signal direction
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
Signal
MSEO0
MSEO1
GND
MDO0
MDO1
GND
MDO2
MDO3
GND
MCKO
MDO4
GND
MDO5
MDO6
GND
MDO7
MDO8
GND
MDO9
MDO10
GND
MDO11
MDO12
GND
MDO15
Pin
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
Pin
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
Signal
VTREF
TCK
TMS
TDI
TDO
NTRST
RDY
EVTI
EVTO
JTAG_RST
NC
GND
NC
NC
GND
NC
NC
GND
NC
NC
GND
MDO13
MDO14
GND
NC
Signal direction
O
O
O
I
O
O
I
O
I
I
50-pin Samtec ERF8 Nexus target connector pinout
The adapter connects to the target via a 50-pin ERM8 connector (for example SAMTEC: ERM8-025-01-L-DEM2-TR). A target should feature a matching part (for example SAMTEC: ERF8-025-05.0-L-DV).
 iSYSTEM, January 2015
42/64
 16-pin 2.54mm Freescale COP Cable Adapter
Ordering code
IC50153
This adapter is used to connect the iC5000 development system to Freescale MPC6xx, MPC82xx, MobileGT,
MPC7xx or MPC83xx based target via COP/JTAG debug interface. It connects to Debug/Trace module
(IC50020) on one side and to the target debug connector on the other side. It can be used for targets featuring 16pin 2.54 pitch target debug connector with Freescale COP pinout.
The following pinout is valid on the target side:
Signal Signal description
Signal
direction
I
Standard JTAG
TDO
O
Standard JTAG
TDI
I
Status (optional)
HALTED
O
Standard JTAG
TCK
O
Standard JTAG
TMS
O
Soft Reset
SRESET
O
Hard Reset
HRESET
I
Status (optional) CKSTP_OUT
Pin Pin
1
3
5
7
9
11
13
15
2
4
6
8
10
12
14
16
Signal
Signal description
QACK#
TRST
VTref
CKSTP_IN
NC
GND
NC
GND
100-ohm pull-down
Standard JTAG
Reference voltage
Status (optional)
Not Connected
Ground
Not Connected
Ground
Signal
direction
O
O
I
O
16-pin Freescale COP target pinout
Note: 16-pin 2.54mm Freescale COP Cable Adapter features resettable fuses on all pins except for pin 15. These
protect debug signals against overcurrent and cycle back to a conductive state after the excessive current fades
away. A signal on pin 15 is protected via 100 ohm serial resistor.
The adapter connects to the target via a 16-pin 2.54 mm connector (for example Yamaichi: FAS-1601-2101-2OBF). A target should feature a matching part (for example WÜRTH ELEKTRONIK: 612 016 216 21).
 iSYSTEM, January 2015
43/64
 51-pin GLENAIR Cable Adapter
Ordering code
IC50154
This adapter is used to connect the iC5000 development system to Freescale MPC5xxx or ST SPC5xxxx based
target via Nexus debug interface. It connects to Debug/Trace module (IC50020) on one side and to the target
debug connector on the other side. Typically it’s used in conjunction with targets operating in harsh
environments, featuring a robust 51-pin GLENAIR target debug connector instead of the popular 38-pin Mictor
target debug connector.
The following pinout is valid on the target side:
Signal direction
I
O
O
O
O
O
O
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
Signal
NC
NC
TDO
RESET
EVTIN
TRST
TMS
TDI
SWCLK/TCK
MDO0
MCKO
EVTO
MSEO0
MDO1
MDO2
MDO3
NC
MSEO1
MDO4
MDO5
MDO6
MDO7
MDO8
MDO10
MDO11
NC
Pin
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
Pin
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
Signal
NC
NC
RDY
VTREF
GND
GND
GND
GND
GND
GND
GND
GND
MDO9
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
Signal direction
I
I
51-pin GLENAIR target pinout
Note: 51-pin GLENAIR Cable Adapter features resettable fuses on pins 5, 6, 7, 8, 9, 11, 13 and 15. These protect
debug signals against overcurrent and cycle back to a conductive state after the excessive current fades away.
Signals on pins 19, 21, 23, 25, 26, 27, 29, 31, 35, 37, 39, 41, 43, 45, 47, 49 and GND are protected via 47 ohm
serial resistors.
The adapter connects to the target via a 51-pin GLENAIR connector (for example GLENAIR - M83513/02-GN).
A target should feature a matching part (for example GLENAIR - M83513/01-GN).
 iSYSTEM, January 2015
44/64
 Mictor 38-pin PPC4xx RISCTrace Cable Adapter
Ordering code
IC50155
Note: iC5000 Debug/Trace module (IC50020) revision D or newer is required to be able to connect and use this
adapter.
This adapter is used to connect the iC5000 development system to Applied Micro PPC4xx based target via
RISCTrace debug interface. It connects between the Debug/Trace module (IC50020) and the target debug
connector. It can be used for targets featuring Mictor 38-pin target debug connector with PPC4xx RISCTrace
pinout.
The following pinout is valid on the target side:
Signal direction
O
O
I
O
O
O
O
I
I
I
I
I
I
I
Signal
NC
NC
GND
HALT
SRST
TDO
NC
TCK
TMS
TDI
NTRST
NC
BS0
BS1
BS2
BS3
BS4
BS5
BS6
Pin
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
Pin
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
Signal
NC
NC
TRCLK
NC
NC
VREF
NC
NC
NC
NC
NC
NC
TS0
TS1
TS2
TS3
TS4
TS5
TS6
Signal direction
I
I
I
I
I
I
I
I
I
PPC4xx RISCTrace target pinout
Note: Mictor 38-pin MPC5xxx Nexus 16-bit Cable Adapter features resettable fuses on pins 7, 9, 11, 12, 15, 17,
19 and 21. These protect debug signals against overcurrent and cycle back to a conductive state after the
excessive current fades away. Signals on pins 6, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37 and 38 are
protected via 47 ohm serial resistors.
The adapter connects to the target via a 38-pin Mictor connector (Tyco Electronics 5767055-1). A target should
feature a matching part (for example Tyco Electronics 5767081-1 in SMT technology).
 iSYSTEM, January 2015
45/64
 50-pin Samtec MPC5xxx Nexus 16-bit Cable Adapter
Ordering code
IC50156
Note: iC5000 Debug/Trace module (IC50020) revision D or newer is required to be able to connect and use this
adapter.
This adapter is used to connect the iC5000 development system to Freescale MPC5xxx or ST SPC56 based
target via Nexus debug interface. It connects between the Debug/Trace module (IC50020) and the target debug
connector. It can be used for targets featuring 50-pin Samtec ERF8-025 target debug connector with MPC5xxx
Nexus pinout.
Jumper J2 (EVTIN)
Under some circumstances it can happen that the debugger cannot find any absolute program counter message in
the analyzed Nexus trace block. Consequentially, trace reconstruction fails and errors or nothing gets displayed
in the trace window. To avoid such situations, the debugger can feed periodic signal to the EVTIN CPU pin
connecting to the on-chip Nexus engine, which then periodically generates and broadcasts program counter
synchronization messages.
In order to use this feature, jumper J2 must be bridged and the ‘Force periodic Nexus SYNC’ option in the
‘Hardware/emulation Options/CPU Setup/Nexus’ tab must be checked. Refer to iSYSTEM ‘Freescale MPC5xxx
& ST SPC56 Family On-Chip Emulation’ technical notes document for more details on the ‘Force periodic
Nexus SYNC’ option use.
Note that the EVTI (Nexus Event In) CPU pin may be shared with other CPU functionalities. For instance, on
MPC5516 the same pin can operate as GPIO, EBI read/write or EVTI. Whenever the CPU pin is configured and
used for EVTI alternate operation, J2 must not be populated in order to prevent electrical conflicts..
Note: In general there is no need to use ‘Force periodic Nexus SYNC’ functionality unless a specific application
code is traced, which does not generate messages containing absolute program counter information. As long as
the user has no problems with the trace use, it is recommended to keep jumper 2 disconnected.
 iSYSTEM, January 2015
46/64
The following pinout is valid on the target side:
Signal direction
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
Signal
MSEO0
MSEO1
GND
MDO0
MDO1
GND
MDO2
MDO3
GND
MCKO
MDO4
GND
MDO5
MDO6
GND
MDO7
MDO8
GND
MDO9
MDO10
GND
MDO11
MDO12
GND
MDO15
Pin
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
Pin
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
Signal
VTREF
TCK
TMS
TDI
TDO
NTRST
NC
EVTI
EVTO
JTAG_RST
NC
GND
NC
NC
GND
NC
NC
GND
NC
NC
GND
MDO13
MDO14
GND
NC
Signal direction
O
O
O
I
O
O
I
O
O
I
I
MPC5xxx and SPC56 50-pin 16-bit Nexus target pinout
Note: 50-pin Samtec MPC5xxx Nexus 16-bit Cable Adapter features resettable fuses on pins 2, 4, 6, 8, 10, 12, 16
and 20. These protect debug signals against overcurrent and cycle back to a conductive state after the excessive
current fades away. All other signals are protected via 47 ohm serial resistor.
The adapter connects to the target via a 50-pin Samtec connector (SAMTEC ERM8-025-01-L-D-EM2). A target
should feature a matching part (for example SAMTEC - ERF8-025-05.0-L-DV in the SMT technology).
 iSYSTEM, January 2015
47/64
 16-pin 2.54mm Infineon JTAG Cable Adapter
Ordering code
IC50160
This adapter is used to connect the iC5000 development system to Infineon XC166, XC2000 and TriCore based
target via JTAG debug interface. It connects to Debug/Trace module (IC50020) on one side and to the target
debug connector on the other side. It can be used for targets featuring 16-pin 2.54mm pitch target debug
connector with Infineon JTAG pinout.
The following pinout is valid on the target side:
Signal
direction
O
I
O
O
O
I
O
Signal description
Standard JTAG
Standard JTAG
(optional)
Standard JTAG
Standard JTAG
Standard JTAG
Break Input
Not Connected
Signal
Pin Pin
TMS
1
TDO
3
CPUCLK 5
TDI
7
TRST
9
TCLK
11
BRK_IN 13
NC
15
Signal
2
VTref
4
GND
6
GND
8
RESET
10 BRK_OUT
12
GND
14 OCDS_E
16
NC
Signal description
Reference voltage
Ground
Ground
Power On Reset
Break Output
Ground
(optional)
Not Connected
Signal
direction
I
O
I
O
16-pin Infineon JTAG target pinout
Mandatory pins on the microcontroller side are TMS, TDO, TDI, TRST, TCLK and RESET. BRK_IN and
BRK_OUT signals can be used optionally.
Note: 16-pin 2.54mm Infineon JTAG Cable Adapter features resettable fuses on all connected pins. These
protect debug signals against overcurrent and cycle back to a conductive state after the excessive current fades
away.
The adapter connects to the target via a 16-pin 2.54 mm connector (for example Yamaichi: FAS-1601-2101-2OBF). A target should feature a matching part (for example WÜRTH ELEKTRONIK: 612 016 216 21).
 iSYSTEM, January 2015
48/64
 10-pin 1.27mm Tricore MEDC17 Cable Adapter
Ordering code
IC50160-MEDC17
This connector has been defined by Bosch and supports JTAG debug interface.
This adapter is used to connect the iC5000 development system to Infineon XC166, XC2000 and TriCore based
target via JTAG debug interface. It connects to Debug/Trace module (IC50020) on one side and to the target
debug connector on the other side. It can be used for targets featuring 10-pin 1.27 mm pitch target debug
connector with Bosch MEDC17 pinout.
The following pinout is valid on the target side:
Signal
direction
O
O
O
I
Signal description
Signal
Break Input
Ground
Standard JTAG
Power On Reset
Reference voltage
~BRK_IN
GND
TMS
~RESET
VTref
Pin Pin
1
3
5
7
9
Signal
2
~TRST
4
TCLK
6 ~BRK_OUT
8
TDI
10
TDO
Signal description
Standard JTAG
Standard JTAG
Break Output
Standard JTAG
Standard JTAG
Signal
direction
O
O
I
O
I
10-pin Bosch MEDC17 target pinout
Mandatory pins on the microcontroller side are TMS, TDO, TDI, ~TRST, TCLK and ~RESET. ~BRK_IN and
~BRK_OUT signals can be used optionally.
Note: 10-pin 1.27mm Tricore MEDC17 Cable Adapter features resettable fuses on all connected pins. These
protect debug signals against overcurrent and cycle back to a conductive state after the excessive current fades
away.
The adapter connects to the target via a 10-pin 1.27mm connector (for example SAMTEC: FFSD-05-01-N). A
target should feature a matching part (for example SAMTEC: SHF-105-01-L-D-TH).
 iSYSTEM, January 2015
49/64
 10-pin 1.27mm Tricore ECU14 Cable Adapter
Ordering code
IC50160-ECU14
This connector has been defined by Bosch and supports JTAG debug interface.
This adapter is used to connect the iC5000 development system to Infineon XC166, XC2000 and TriCore based
target via JTAG debug interface. It connects to Debug/Trace module (IC50020) on one side and to the target
debug connector on the other side. It can be used for targets featuring 10-pin 1.27 mm pitch target debug
connector with Bosch ECU14 pinout.
The following pinout is valid on the target side:
Signal
direction
O
O
I/O
Signal description
Signal
Ground
Standard JTAG
Standard JTAG
User specific
Not Connected
GND
~TRST
TMS
USERIO
NC
Pin Pin
1
3
5
7
9
2
4
6
8
10
Signal
Signal description
TCLK
TDO
TDI
Vref
~RESET
Standard JTAG
Standard JTAG
Standard JTAG
Reference voltage
Power On Reset
Signal
direction
O
I
O
I
O
10-pin Bosch ECU14 target pinout
Mandatory pins on the microcontroller side are TMS, TDO, TDI, ~TRST, TCLK and ~RESET. USERIO signal
can be used optionally.
Note: 10-pin 1.27mm TriCore ECU14 Cable Adapter features resettable fuses on all connected pins. These
protect debug signals against overcurrent and cycle back to a conductive state after the excessive current fades
away.
The adapter connects to the target via a 10-pin 1.27mm connector (for example SAMTEC: SFM-105-01-S-D). A
target should feature a matching part (for example SAMTEC: TFM-105-01-L-D).
 iSYSTEM, January 2015
50/64
 10-pin 1.27mm Infineon DAP Cable Adapter
Ordering code
IC50161
Note: This product is obsolete and is fully replaced with IC50163
This adapter is used to connect the iC5000 development system to Infineon XC166, XC2000 or TriCore based
target. It connects to Debug/Trace module (IC50020) on one side and to the target debug connector on the other
side. It can be used for targets featuring 10-pin 1.27mm pitch target debug connector with Infineon DAP pinout.
From Rev. E1 on, Infineon 3-pin DAP debug interface (Wide Mode) is supported (labeled “Infineon DAP2”).
Older revisions support 2-pin DAP (one clock line + one bidirectional data line) interface only (labeled “Infineon
DAP”).
From Rev. D1 on, Hot Attach operation without connecting/disconnecting the adapter from the target is
supported. Rev. D1 newly introduces jumper J1.
With jumper J1 in position 1-2 (default), normal debug operation is configured. The debugger drives MCU reset
line low during the initial debug connection and then takes control over the microcontroller.
With jumper J1 in position 2-3, Hot Attach operation is configured. In this case, all debug signals from the
iC5000 unit are disconnected and the target starts running as soon as the power is applied to the target. When
Hot Attach command is issued from winIDEA, the debugger connects to the MCU and control over the MCU is
taken without resetting the MCU. Depending on the target MCU, refer to the XC166/XC2000 or the TriCore
technical notes document for more details on Hot Attach configuration and use.
The following pinout is valid on the target side:
Signal
Signal description
direction
I
Reference voltage
Ground
Ground
Not Connected
Ground
Signal
Vref
GND
GND
NC
GND
Pin Pin
1
3
5
7
9
2
4
6
8
10
Signal
Signal description
DAP1
DAP0
USER_IO
USER_IN
RESET
Bidirectional data
DAP clock
Optional
Optional
System Reset
Signal
direction
I/O
O
O
O
I/O
10-pin Infineon DAP pinout
Note: 10-pin 1.27mm Infineon DAP Cable Adapter features resettable fuses on pins 1, 2, 3, 4, 5, 6, 8, 9 and 10.
These fuses protect debug signals against overcurrent and cycle back to a conductive state after the excessive
current fades away.
The adapter connects to the target via a 10-pin 1.27mm connector (for example SAMTEC: FFSD-05-01-N). A
target should feature a matching part (for example SAMTEC: SHF-105-01-L-D-TH).
 iSYSTEM, January 2015
51/64
 6-pin 2.54mm Infineon I2C Cable Adapter
Ordering code
IC50162
This adapter is used to connect the iC5000 development system to Infineon SP37/SP40 based target. It connects
to Debug/Trace module (IC50020) on one side and to the target debug connector on the other side. It can be used
for targets featuring 6-pin 2.54mm pitch target debug connector with Infineon I2C pinout.
The following pinout is valid on the target side:
Signal
direction
Signal description
Signal
Pin
Reference voltage
VDDBAT
PP0
PP1
GND
PP2
PP3
1
2
3
4
5
6
I/O
I/O
Ground
I/O
I/O
6-pin 2.54mm Infineon I2C pinout
Note: 6-pin 2.54mm Infineon I2C Cable Adapter features resettable fuses on pins 1, 2, 3, 4, 5 and 6. These fuses
protect debug signals against overcurrent and cycle back to a conductive state after the excessive current fades
away.
Emulation Notes
MCU can run in normal, debug or programming mode. Mode is always selected after power on and cannot be
changed later. Because of this VDDBAT (pin 1 on the debug connector) is a power supply output from the
emulator and the target power supply (battery) must be removed while debugging. Before the debug
download takes place, power off/on sequence is generated by the emulator and programming mode selected.
During the debug download, first user flash is erased, then the application code programmed into the flash and at
the end the complete flash is read back. This last step is required since the code memory can be no longer read
once the MCU is in the debug mode. Beside of the user flash, SP41 has also Firmware ROM which cannot be
read by the debugger.
After the debug download, the MCU is reset again since it was in the programming mode during the debug
download. This means a power off/on sequence is initiated again and the debug mode selected. This same
sequence is also applied when debug reset command is executed from winIDEA.
During debugging (MCU in debug mode) two hardware execution breakpoints are available. No software
breakpoints in flash are available since user flash cannot be modified in the debug mode.
Real time access is not available.
On-chip debug logic does not implement a stop command. Therefore the MCU cannot be stopped by the
debugger while the application is running. MCU will stop only if hardware execution breakpoint is hit.
Note: 4-pin “connector” located on the side of the adapter is meant for future extensions of debug functionalities.
Currently it provides no functionality.
The adapter connects to the target via a 6-pin 2.54 mm connector (for example LUMBERG: 2,5 MBX 06). A
target should feature a matching part (for example WÜRTH ELEKTRONIK: 613 006 111 21).
 iSYSTEM, January 2015
52/64
 10-pin 1.27mm Infineon DAP2 Wide Cable Adapter
Ordering code
IC50163
This adapter is used to connect the iC5000 development system to Infineon XC166, XC2000 or TriCore based
target. It connects to Debug/Trace module (IC50020) on one side and to the target debug connector on the other
side. It can be used for targets featuring 10-pin 1.27mm pitch target debug connector with Infineon DAP pinout.
From Rev. E1 on, Infineon 3-pin DAP debug interface (Wide Mode) is supported (labeled “Infineon DAP2”).
With jumper J1 in position 1-2 (default), normal debug operation is configured. The debugger drives MCU reset
line low during the initial debug connection and then takes control over the microcontroller.
With jumper J1 in position 2-3, Hot Attach operation is configured. In this case, all debug signals from the
iC5000 unit are disconnected and the target starts running as soon as the power is applied to the target. When
Hot Attach command is issued from winIDEA, the debugger connects to the MCU and control over the MCU is
taken without resetting the MCU. Depending on the target MCU, refer to the XC166/XC2000 or the TriCore
technical notes document for more details on Hot Attach configuration and use.
The following pinout is valid on the target side:
Signal
Signal description
direction
I
Reference voltage
Ground
Ground
Not Connected
Ground
Signal
Vref
GND
GND
NC
GND
Pin Pin
1
3
5
7
9
2
4
6
8
10
Signal
Signal description
DAP1
DAP0
DAP2
USER_IN
RESET
Bidirectional data
DAP clock
Bidirectional data
Optional
System Reset
Signal
direction
I/O
O
I/O
O
I/O
10-pin Infineon DAP pinout
Note: 10-pin 1.27mm Infineon DAP Cable Adapter features resettable fuses on pins 1, 2, 3, 4, 5, 6, 8, 9 and 10.
These fuses protect debug signals against overcurrent and cycle back to a conductive state after the excessive
current fades away.
The adapter connects to the target via a 10-pin 1.27mm connector (for example SAMTEC: FFSD-05-01-N). A
target should feature a matching part (for example SAMTEC: SHF-105-01-L-D-TH).
 iSYSTEM, January 2015
53/64
 16-pin 2.54mm Renesas 78K0R Serial Cable Adapter
Ordering code
IC50170
This adapter is used to connect the iC5000 development system to Renesas 78K0R based target via Serial debug
interface. It connects to Debug/Trace module (IC50020) on one side and to the target debug connector on the
other side. It can be used for targets featuring 16-pin 2.54 pitch target debug connector with 78K0R pinout.
The following pinout is valid on the target side:
Signal Signal description
direction
Ground
I/O
Communication
line
I/O
Communication
line
Not Connected
Not Connected
Not Connected
Not Connected
I
Reset In
Signal
GND
TOOL0
(RxD/TxD)
TOOL0
(RxD/TxD)
NC
NC
NC
NC
RESET IN
Pin Pin
Signal
Signal description
1
3
2
4
RESET OUT
Vcc
Reset Out
Power Supply
5
6
NC
Not Connected
7
9
11
13
15
8
NC
10
NC
12
NC
14
FLMD0
16 TOOL1 (CLK)
Not Connected
Not Connected
Not Connected
Flash Mode
Clock Input
Signal
direction
O
I/O
O
I
16-pin Renesas 78K0R Serial Debug target pinout
If the ‘Supply 5V to the target’ option is checked in the ‘Hardware/Emulation Options/CPU Setup/Advanced’
tab, the debugger supplies 5V at Vcc pin (pin 4) of the target debug connector, which can be used to power the
target. Maximum target current consumption should not exceed 50mA.
Note: 16-pin Renesas 78K0R Serial Debug Cable Adapter features resettable fuses on all connected pins. These
protect debug signals against overcurrent and cycle back to a conductive state after the excessive current fades
away.
Note: If ‘RESET IN’ (target reset detection) is not connected to the target debug connector, make sure that 10k
pull up is connected to this pin (target debug connector pin 15) or the debugger may exhibit unpredictable
behaviour.
The adapter connects to the target via a 16-pin 2.54 mm connector (for example Yamaichi: FAS-1601-2101-2OBF). A target should feature a matching part (for example WÜRTH ELEKTRONIK: 612 016 216 21).
 iSYSTEM, January 2015
54/64
 20-pin 2.54mm Renesas V850/RH850 Cable Adapter
Ordering code
IC50171
This adapter is used to connect the iC5000 development system to Renesas V850 based target. It connects to
Debug/Trace module (IC50020) on one side and to the target debug connector on the other side. It can be used
for targets featuring 20-pin 2.54 pitch target debug connector with V850 pinout.
The following pinout is valid on the target side:
Signal
direction
Signal description
Signal
Pin Pin
Signal
Signal description
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
1
3
5
7
9
11
13
15
17
19
2
TCK
4
TMS
6
TDI
8
TRST
10
NC
12 RESET
14 FLMD0
16 ~RDY
18
TDO
20
VDD
Debug JTAG
Debug JTAG
Debug JTAG
Debug JTAG
Not Connected
CPU Reset
Flash Mode
Synchronization
Debug JTAG
Reference voltage
Signal
direction
O
O
O
O
I/O
O
I
I
I
20-pin Renesas V850/RH850 target pinout
Note: 20-pin 2.54mm V850/RH850 Cable Adapter features resettable fuses on all pins except for pin 16. These
fuses protect debug signals against overcurrent and cycle back to a conductive state after the excessive current
fades away. A signal on pin 16 is protected via 100 ohm serial resistor.
The adapter connects to the target via a 20-pin 2.54 mm connector (for example Yamaichi: FAS-2001-2101-2OBF). A target should feature a matching part (for example WÜRTH ELEKTRONIK: 612 020 216 21).
 iSYSTEM, January 2015
55/64
 26-pin KEL Renesas V850 Cable Adapter
Ordering code
IC50172
This adapter is used to connect the iC5000 development system to Renesas V850 based target. It connects to
Debug/Trace module (IC50020) on one side and to the target debug connector on the other side. It can be used
for targets featuring 26-pin KEL target debug connector with V850 pinout.
The following pinout is valid on the target side:
Signal
direction
I
Signal description
Signal
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Reserved
Reserved
Reference Voltage
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
Reserved
Reserved
VTRef
Pin Pin
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
Signal
Signal description
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
DDI
DCK
DMS
DDO
DRST
RESET
FLMD0
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
N-Wire
N-Wire
N-Wire
N-Wire
N-Wire
Reset
Flash Mode
Signal
direction
O
O
O
I
O
O
O
26-pin Renesas V850 target pinout
Note: 26-pin KEL V850 Cable Adapter features resettable fuses on all connected signals. These fuses protect
debug signals against overcurrent and cycle back to a conductive state after the excessive current fades away.
This adapters ends with a KEL connector (part number 8825E-026-175). Normally, the target side has KEL
connector, part number 8830E-026-170S populated. For more details see 8825E Series at http://www.kel.jp/.
 iSYSTEM, January 2015
56/64
 14-pin 2.54mm Renesas SuperH Cable Adapter
Ordering code
IC50173
This adapter is used to connect the iC5000 development system to Renesas SuperH based target. It connects to
Debug/Trace module (IC50020) on one side and to the target debug connector on the other side. It can be used
for targets featuring 14-pin 2.54 pitch target debug connector with SuperH pinout.
The following pinout is valid on the target side:
Signal
direction
Signal description
Signal
O
O
I
O
O
O
Debug JTAG
Debug JTAG
Debug JTAG
Mode select
Debug JTAG
Debug JTAG
RESET IN
TCK
NTRST
TDO
ASEBRK
TMS
TDI
RESET
Pin Pin
1
3
5
7
9
11
13
Signal
Signal description
2
NC
Not Connected
4
ASEMD
Status read
6
GND
Ground
8
VTREF
Reference voltage
10
GND
Ground
12
GND
Ground
14 GND_DETECT
Ground detect
Signal
directio
n
I
O
I
14-pin SuperH target pinout
Note: 14-pin 2.54mm SuperH cable adapter features resettable fuses on all pins except for pin 14, where serial
resistor of 100ohm and pull up resistor of 10k ohm is used. These fuses protect debug signals against overcurrent
and cycle back to a conductive state after the excessive current fades away.
The adapter connects to the target via a 14-pin 2.54 mm connector (for example Yamaichi: FAS-1401-2101-2OBF). A target should feature a matching part (for example WÜRTH ELEKTRONIK: 612 014 216 21).
 iSYSTEM, January 2015
57/64
 10-pin 2.54mm Renesas 78K0 Serial Cable Adapter
Ordering code
IC50174
This adapter is used to connect the iC5000 development system to Renesas 78K0 based target via Serial debug
interface. It connects to Debug/Trace module (IC50020) on one side and to the target debug connector on the
other side. It can be used for targets featuring 10-pin 2.54 pitch target debug connector with 78K0 pinout.
The following pinout is valid on the target side:
Signal
Signal description
Signal
direction
I
Reset In
RESET IN
O
Flash Mode
FLMD0
I/O
Communication line
X2
O
Communication line
X1
Not Connected
NC
Pin Pin
1
3
5
7
9
Signal
2 RESET OUT
4
TARVCC
6
GND
8
GND
10
5V OUT
Signal description
Reset Out
Target Vcc
Ground
Ground
5V Power Supply
Signal
direction
O
I
O
10-pin Renesas 78K0 Serial Debug target pinout
If the ‘Supply 5V to the target’ option is checked in the ‘Hardware/Emulation Options/CPU Setup/Advanced’
tab, the debugger supplies 5V at 5V OUT pin (pin 10) of the target debug connector, which can be used to
power the target. Maximum target current consumption should not exceed 50mA.
Note: 10-pin Renesas 78K0R Serial Debug Cable Adapter features resettable fuses on all connected pins. These
protect debug signals against overcurrent and cycle back to a conductive state after the excessive current fades
away.
Note: If ‘RESET IN’ (target reset detection) is not connected to the target debug connector, make sure that 10k
pull up is connected to this pin (target debug connector pin 1) or the debugger may exhibit unpredictable
behavior.
The adapter connects to the target via a 10-pin 2.54 mm connector (for example Yamaichi: FAS-1001-2101-2OBF). A target should feature a matching part (for example WÜRTH ELEKTRONIK: 612 010 216 21).
An additional adapter (ordering code IAPIN10PIN16NEC78K) must be ordered separately in order to connect to
a target featuring 16-pin 2.54 pitch target debug connector.
Ordering code
 iSYSTEM, January 2015
IAPIN10PIN16NEC78K
58/64
IAPIN10PIN16NEC78K
With this adapter, the following pinout is valid on the target side:
Signal
direction
O
I/O
I
Signal description
Signal
Ground
GND
Not Connected
NC
Not Connected
NC
Not Connected
NC
Communication line
X1
Not Connected
NC
Communication line
X2
Reset In
RESET IN
Pin Pin
1
3
5
7
9
11
13
15
Signal
Signal description
2 RESET OUT
4
TARVCC
6
NC
8
NC
10
NC
12
NC
14
FLMD0
16
NC
Reset Out
Target Vcc
Not Connected
Not Connected
Not Connected
Not Connected
Flash Mode
Not Connected
Signal
direction
O
I
O
16-pin Renesas 78K0 Serial Debug target pinout
The adapter connects to the target via a 10-pin 2.54 mm connector (for example Yamaichi: FAS-1001-2101-2OBF). A target should feature a matching part (for example WÜRTH ELEKTRONIK: 612 010 216 21).
 iSYSTEM, January 2015
59/64
 14-pin 2.54mm Renesas RL78 Serial Cable Adapter
Ordering code
IC50175
This adapter is used to connect the iC5000 development system to Renesas RL78 based target via Serial debug
interface. It connects to Debug/Trace module (IC50020) on one side and to the target debug connector on the
other side. It can be used for targets featuring 14-pin 2.54 pitch target debug connector with RL78 pinout.
The following pinout is valid on the target side:
Signal
direction
I/O
O
Signal description
Signal
Not Connected
NC
Not Connected
NC
Communication line
TOOL0
Not Connected
NC
Power supply pin
EVDD
Not Connected
NC
Reset Out
RESET_OUT
Pin Pin
1
3
5
7
9
11
13
Signal
Signal description
2
GND
Ground
4
NC
Not Connected
6
RESET_IN
Reset In
8
VDD
Power supply pin
10 RESET_OUT
Reset Out
12
GND
Ground
14
GND
Ground
Signal
direction
I
O
14-pin Renesas RL78 Serial Debug target pinout
If the ‘Supply 5V to the target’ option is checked in the ‘Hardware/Emulation Options/CPU Setup/Advanced’
tab, the debugger supplies 5V at VDD pin (pin 8) of the target debug connector, which can be used to power the
target. Maximum target current consumption should not exceed 50mA.
Some RL78 devices may have two power supply pins (EVDD and VDD). Both must be connected to debug
connector.
If ‘Vref’ option for Debug I/O levels is checked in the ‘Hardware/Emulation Options/Hardware’ tab the EVDD
on pin 9 is used as TAR-VREF.
Note: If ‘RESET IN’ (target reset detection) is not connected to the target debug connector, make sure that 10k
pull up is connected to this pin (target debug connector pin 6) or the debugger may exhibit unpredictable
behavior.
The adapter connects to the target via a 14-pin 2.54 mm connector (for example Yamaichi: FAS-1401-2101-2OBF). A target should feature a matching part (for example WÜRTH ELEKTRONIK: 612 014 216 21).
 iSYSTEM, January 2015
60/64
 14-pin 2.54mm Renesas RH850 Cable Adapter
Ordering code
IC50176
This adapter is used to connect the iC5000 development system to Renesas V850 based target. It connects to
Debug/Trace module (IC50020) on one side and to the target debug connector on the other side. It can be used
for targets featuring 14-pin 2.54 pitch target debug connector with V850 pinout.
The following pinout is valid on the target side:
Signal
direction
O
O
I
O
O
I
I/O
Signal description
Signal
Pin Pin
Signal
Signal description
Debug JTAG
Debug JTAG
Debug JTAG
Debug JTAG
Debug JTAG
Synchronization
CPU Reset
TCK
TRST
TDO
TDI
TMS
~RDY
RESET
1
3
5
7
9
11
13
GND
FLMD0
FLMD1
VTREF
NC
GND
GND
Ground
Flash Mode
Flash Mode
Reference voltage
Not Connected
Ground
Ground
2
4
6
8
10
12
14
Signal
direction
O
O
I
14-pin Renesas RH850 target pinout
Note: 14-pin 2.54mm RH850 Cable Adapter features resettable fuses on all pins except for pin 11. These fuses
protect debug signals against overcurrent and cycle back to a conductive state after the excessive current fades
away. A signal on pin 11 is protected via 100 ohm serial resistor.
The adapter connects to the target via a 14-pin 2.54 mm connector (for example Yamaichi: FAS-1401-2101-2OBF). A target should feature a matching part (for example WÜRTH ELEKTRONIK: 612 014 216 21).
 iSYSTEM, January 2015
61/64
 Mictor 38-pin Renesas RH850 Nexus 16-bit Cable Adapter
Ordering code
IC50177
This adapter is used to connect the iC5000 development system to Renesas RH850 based target exposing Nexus
trace interface over the Mictor 38-pin connector. It connects to Debug/Trace module IC50020 on one side and to
the target debug connector on the other side. It can be used for targets featuring Mictor 38-pin debug & trace
connector with the RH850/F1H Nexus pinout.
Jumper J1 on the adapter can be used to isolate (jumper removed) the target microcontroller EVTI input pin from
the debugger, which can optionally control it too.
The following pinout is valid on the target side:
Signal direction
I
I
I
Signal
MDO12
MDO14
MDO9
NC
NRESET
TDO
MDO10
TCK
TMS
TDI
TRST
MDO11
NC
NC
NC
NC
NC
NC
FLMD0
O
I
I
O
O
O
O
I
O
Pin
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
Pin
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
Signal
MDO13
MDO15
NC
MDO8
EVTI
VTREF
~RDY
MDO7
MDO6
MDO5
MDO4
MDO3
MDO2
MDO1
MDO0
EVTO
MCKO
MSEO1
MSEO0
Signal direction
I
I
I
O
I
I
I
I
I
I
I
I
I
I
I
I
I
I
Mictor 38-pin Renesas RH850/F1H 16-bit Nexus target pinout
Note: Mictor 38-pin Renesas RH850 Nexus 16-bit Cable Adapter features resettable fuses on pins 9, 11, 12, 15,
17, 19, 21, 37. Fuse on pin 33 is not assembled. The fuses protect debug signals against overcurrent and cycle
back to a conductive state after the excessive current fades away. All other signals are protected via 47 ohm
serial resistor.
The adapter connects to the target via a 38-pin Mictor connector (Tyco Electronics 5767055-1). A target should
feature a matching part (for example Tyco Electronics 5767081-1 in SMT technology).
 iSYSTEM, January 2015
62/64
 4-pin ERNI ST STM8 Cable Adapter
Ordering code
IC50190
This adapter is used to connect the iC5000 development system to ST STM8 based target. It connects to the
Debug/Trace module (IC50020) on one side and to the target debug connector on the other side. It can be used
for targets featuring 4-pin ERNI target debug connector with the STM8 pinout.
The following pinout is valid on the target side:
Pin
Signal
Signal description
1
2
3
4
VDD
SWIO
GND
RST
Reference voltage
Debug SWIM pin
Ground
Reset
Signal
direction
I
I/O
O
4-pin ERNI ST STM8 target pinout
Note: 4-pin ERNI ST STM8 Cable Adapter features resettable fuses on all pins. These fuses protect debug
signals against overcurrent and cycle back to a conductive state after the excessive current fades away.
The adapter ends with the ERNI MiniBridge 4-pin connector female (P/N 839033). On the target side, ERNI
MiniBridge 4-pin connector right angle male (P/N 214012) or ERNI MiniBridge 4-pin connector vertical male
(P/N 284697) can be used.
 iSYSTEM, January 2015
63/64
Troubleshooting
It is highly recommended to read the technical notes document for your specific microcontroller family before
contacting iSYSTEM technical support. This document can be downloaded from www.isystem.com but
typically it comes delivered with the development system. It contains all the information related to the debugging
including some troubleshooting tips.
Operating Environment:
Operating temperature: between 10°C and 40°C
Humidity: 5% to 80% RH
Storage temperature: between -10°C and 60°C
Dimensions: 127 x 127x 54 mm
Note: Consult with iSYSTEM when using equipment outside of these parameters.
Disclaimer: iSYSTEM assumes no responsibility for any errors which may appear in this document, reserves the
right to change devices or specifications detailed herein at any time without notice, and does not make any
commitment to update the information herein.
 iSYSTEM. All rights reserved.
 iSYSTEM, January 2015
64/64
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement