Release Notes for Cisco Aironet Access Points and Bridges for

Release Notes for Cisco Aironet Access Points and Bridges for
Release Notes for Cisco Aironet Access Points
and Bridges for Cisco IOS Release 15.2(4)JB4
March 2014
OL-31714-01
These release notes describe features, enhancements, and caveats for Cisco IOS Release 15.2(4)JB4.
This release supports these Cisco Aironet autonomous access points:
•
AP 702
•
AP 802
•
AP 1040
•
AP 1140
•
AP 1260
•
AP 1530
•
AP 1550(128MB only)
The supported versions are listed in Table 1
Note
•
AP 1600
•
AP 2600
•
AP 3500
•
AP 3600
•
AP 3700 (Site survey only)
You cannot use HTTPS file transfer to upgrade to Cisco IOS Release 15.2(4)JB4 from previous releases.
Because of the image size for this release, you must use TFTP or FTP file transfer for the upgrade. Refer
to the upgrade instructions at this URL:
http://www.cisco.com/en/US/docs/wireless/access_point/12.4_10b_JA/configuration/guide/scg12410bchap20-firmware.html#wp1035507
Cisco Systems, Inc.
www.cisco.com
Contents
Contents
These release notes contain these sections:
•
Introduction, page 2
•
System Requirements, page 2
•
New Features and Platforms in this Release, page 5
•
Important Notes, page 6
•
Caveats, page 14
•
Troubleshooting, page 15
•
Obtaining Documentation, Obtaining Support, and Security Guidelines, page 16
Introduction
The Cisco Aironet Access Point is a wireless LAN transceiver that acts as the connection point between
wireless and wired networks or as the center point of a standalone wireless network. In large
installations, the roaming functionality provided by multiple access points enables wireless users to
move freely throughout the facility while maintaining uninterrupted access to the network.
System Requirements
You can install the 32 MB Cisco IOS Release 15.2(4)JB3a on all 802, 1040, 1140, 1260, 1550, 1600,
2600, 3500, and 3600 series access points. New APs 702 and 1530 support 128 MB minimum flash and
AP 3700 supports 64 MB minimum flash.
Finding the Cisco IOS Software Release
To find the version of Cisco IOS software that is running on your access point, use a Telnet session to
log into the access point, and enter the show version EXEC command. This example shows command
output from an access point that is running Cisco IOS Release 15.2(4)JB4:
ap1260AG> show version
Cisco IOS Software, C1260 Software (AP3G1-K9W7-M), Version 15.2(4)JB4
Copyright (c) 1986-2010 by Cisco Systems, Inc.
On access points running Cisco IOS software, you can also find the software release on the System
Software Version page in the access point’s web-browser interface. If your access point does not run
Cisco IOS software, the software release appears at the top left of most pages in the web-browser
interface.
Upgrading to a New Software Release
To upgrade your access point or bridge software, follow these steps:
Step 1
Follow this link to the Cisco home page:
Release Notes for Cisco Aironet Access Points and Bridges for Cisco IOS Release 15.2(4)JB4
2
OL-30935-01
System Requirements
http://www.cisco.com
Step 2
Click Support. The Support and Documentation page appears.
Step 3
Under the Select a Product Name, click Wireless. The Product/Technology Support page appears.
Step 4
Under the Make a Selection to Continue section, click Access Point. Products and Access Point are
highlighted.
Step 5
Select the access point model for which you need the information. For example, click the Cisco Aironet
1260 series. A list of documents appears.
Step 6
Click Configure. A list of configuration documents appears.
Step 7
Click Cisco IOS Software Configuration Guide for Cisco Aironet Access Points, 15.2(4)JB4.
Step 8
Navigate to the Managing Firmware and Software chapter.
For information on Cisco IOS software, click this link to browse to the Cisco IOS Software Center on
Cisco.com:
http://www.cisco.com/cisco/software/navigator.html
The new Cisco IOS software is supported only in these versions of 1550 series :
Table 1
Note
Supported Versions
Version
First VID with 128 MB
1552E
VID 04
1552EU
VID 01 (all)
1552I
VID 03
1552H
VID 04
1552S
VID 01 (all)
AP 1550 does not support 64 MB Cisco IOS Release starting from 15.2(4)JA1 in autonomous mode.
Converting a Lightweight Access Point Back to Autonomous Mode
You can convert an access point from lightweight mode back to autonomous mode by loading a Cisco
IOS Release that supports autonomous mode. If the access point is associated with a controller, you can
use the controller to load the Cisco IOS release. If the access point is not associated with a controller,
you can load the Cisco IOS release using TFTP.
The image files and their supported access points are listed in Table 2.
Table 2
Image File Names
Image File
Supported Access Point
Ap3g2
2600I/2600E, 3600I/3600E, 3700I/3700E
Ap3g1
3500I/3500E, 1260I/1260E
Ap1g1
702
Release Notes for Cisco Aironet Access Points and Bridges for Cisco IOS Release 15.2(4)JB4
OL-30935-01
3
System Requirements
Table 2
Image File Names
Image File
Supported Access Point
Ap1g3
1530I/1530E
Ap1g2
1600I/1600E
1520
1552E, 1552EU, 1552S, 1552I, 1552H
1140
1040 and c1140
Disabling Radios to Prevent Unexpected Reboots When Upgrading the System Software
If your access point runs Cisco IOS Release 12.2(11)JA, 12.2(11)JA1, or 12.2(11)JA2, your access point
might unexpectedly reboot after you upgrade to a later Cisco IOS release. However, after the access point
reboots, the upgrade is complete and the access point operates normally. It is recommended to disable
the radio interfaces before upgrading the software to prevent the access point from rebooting
unexpectedly.
To disable the radio interfaces using the access point’s web-browser interface, which you can access
through the access point's Ethernet port, follow these steps:
Step 1
Browse to the Network Interfaces: Radio Settings page. Figure 1 shows the top portion of the Network
Interfaces: Radio Settings page.
Figure 1
Network Interfaces: Radio Settings Page
Release Notes for Cisco Aironet Access Points and Bridges for Cisco IOS Release 15.2(4)JB4
4
OL-30935-01
New Features and Platforms in this Release
Step 2
Choose Disable to disable the radio.
Step 3
Click Apply at the bottom of the page.
Step 4
If your access point has two radios, repeat these steps for the second radio.
Beginning in privileged EXEC mode, follow these steps to disable the access point radios using the
access point CLI:
Command
Purpose
Step 1
configure terminal
Enters global configuration mode.
Step 2
interface dot11radio {0 | 1}
Enters interface configuration mode for the radio interface. The
2.4-GHz radio is radio 0, and the 5-GHz radio is radio 1.
Step 3
shutdown
Disables the radio port.
Step 4
end
Returns to privileged EXEC mode.
Step 5
copy running-config startup-config (Optional) Saves your entries in the configuration file.
If your access point has two radios, repeat these steps for the second radio. Use the no form of the
shutdown command to enable the radio.
Supported Browsers
These browsers are supported:
•
Internet Explorer 8.x and later
•
Firefox 3.x and later
New Features and Platforms in this Release
There are no new features in this release. For more information about the updates in this release, see the
Caveats section.
Release Notes for Cisco Aironet Access Points and Bridges for Cisco IOS Release 15.2(4)JB4
OL-30935-01
5
Installation Notes
Installation Notes
This section contains information that you should keep in mind when installing 702, 802, 1040, 1140,
1260, 1530, 1550, 1600, 2600, 3500, 3600, and 3700 series access points.
Access Points
This section contains installation notes for access points.
Installation in Environmental Air Space
Cisco Aironet 1040, 1140, 1250, 1260, and 2600 series access points provide adequate fire resistance
and low smoke-producing characteristics suitable for operation in a building's environmental air space,
such as above suspended ceilings, in accordance with Section 300-22(C) of the National Electrical Code
(NEC) and Sections 2-128, 12-010(3) and 12-100 of the Canadian Electrical Code, Part 1, C22.1.
Caution
The power injector does not provide fire resistance and low smoke-producing characteristics and is not
intended for use in extremely high or low temperatures or in environmental air spaces such as above
suspended ceilings.
Antenna Installation
For instructions on the proper installation and grounding of external antennas for 1550, 1260, 1600E,
2600, E3500E, and 3600E access points, refer to the National Fire Protection Association’s NFPA 70,
National Electrical Code, Article 810, and the Canadian Standards Association’s Canadian Electrical
Code, Section 54.
Warning
Do not install the antenna near overhead power lines or other electric light or power circuits, or
where it can come into contact with such circuits. When installing the antenna, take extreme care
not to come into contact with such circuits, as they may cause serious injury or death.
Important Notes
This section describes important information about access points and bridges.
Use FTP or TFTP File Transfer to Upgrade to Cisco IOS Release 15.2(4)JB4
You cannot use HTTPS file transfer to upgrade to Cisco IOS Release 15.2(4)JB4 from previous releases.
Because of the image size for this release, you must use FTP or TFTP file transfer for the upgrade. Refer
to the upgrade instructions at this URL:
http://www.cisco.com/en/US/docs/wireless/access_point/12.4_10b_JA/configuration/guide/scg12410bchap20-firmware.html#wp1035507
Release Notes for Cisco Aironet Access Points and Bridges for Cisco IOS Release 15.2(4)JB4
6
OL-30935-01
Important Notes
Cisco 1040/1140 series Access Points May Record "watchdog timer expired" as
Last Reset Reason
This error message sometimes appears as the last reset reason when the access points are power cycled:
Watchdog timer expired
This symptom is observed only in the Cisco 1040/1140 series access point and does not have any impact
on functionality. Ignore the “watchdog timer expired” reason after an access point has been power
cycled. You can also overwrite the reset reason to “reload” by rebooting with command operation.
Regulatory Update for Japan
This release supports the U regulatory domain for the W52 frequency set (channels 36, 40, 44, and 48)
in Japan for the Cisco Aironet 1230 series. This support was added for the Cisco Aironet 1130 series in
Cisco IOS Software Release 12.4(3G)JA, which shipped previously. Cisco access points specified for
this new domain ship with a U domain radio. Installed J domain access points are automatically upgraded
to the U domain status with this release.
For the latest Cisco WLAN compliance status, visit this URL:
http://www.cisco.com/en/US/prod/collateral/wireless/ps5679/ps5861/product_data_sheet0900aecd805
37b6a_ps430_Products_Data_Sheet.html.
Point-to-Point and Point-to-Multipoint Bridging Support for 802.11n Platforms
The point-to-point and point-to-multipoint bridging is supported on the Cisco Aironet 1040, 1140, 1260,
1600, 2600, 3500 and 3600 series access points (802.11n platforms). The 5-GHz bands support 20 and
40-MHz channel widths, and the 2.4-GHz bands support only a 20-MHz channel width.
The following items are supported for AP1040, AP1140, AP1260, AP1600, AP2600, AP3500, and
AP3600 bridging:
Note
•
MIMO, short-range bridging (on campus or inter-building bridge deployments), with dipole and
MIMO antennas (line of sight and short range) under 1 km.
•
20-MHz and 40-MHz 802.11n support.
•
Workgroup bridge (WGB) short-range support.
•
SISO (single-in, single-out), MCS 0-7 and legacy bridge rates (802.11 a/b/g and 802.11n) using one
outdoor antenna.
This is only supported using short range links and is not a replacement for the AP-1300/1400 or other
bridge products.
The following items are not supported for AP 702, AP1040, AP1140, AP1260, AP1600, AP2600,
AP3500 and AP3600 bridging:
•
The distance CLI command: long-range links over 1 km currently are not supported; therefore, the
distance command is not supported.
Release Notes for Cisco Aironet Access Points and Bridges for Cisco IOS Release 15.2(4)JB4
OL-30935-01
7
Important Notes
•
Outdoor MIMO bridging using external antennas has not been fully tested and is not fully supported
with this release.
Low Throughput Seen on Access Points with 16 BSSIDs Configured
If your network uses 16 BSSIDs with 1 and 2-Mbps data rates, access points might experience very low
throughput due to high management traffic.
802.11n HT Rates Apply Only to No Encryption or WPA2/AES Encryption
As per the 802.11n amendment, the 802.11n HT rates apply only to no encryption or WPA2/AES
encryption. They do not apply to WEP or WPA encryption. If WEP or TKIP encryption is used, the
access point and any 802.11n clients will not transmit at HT rates. Legacy rates (802.11a/b/g) will be
used for any clients using WEP or TKIP encryption.
Layer 3 Not Supported with NAC for MBSSID
Layer 3 is not supported with NAC for MBSSID in this release.
Change to Default IP Address Behavior
Cisco IOS Release 12.3(2)JA and later releases change the default behavior of access points that request
an IP address from a DHCP server
When you connect a 1040, 1130, 1140, 1250, or 1260 series access point or a 1300 series outdoor access
point/bridge with a default configuration to a LAN, the access point requests an IP address from a DHCP
server and, if it does not receive an address, continues to send requests indefinitely.
Changes to the Default Configuration—Radios Disabled and No Default SSID
The radio or radios are disabled by default, and there is no default SSID. You must create an SSID and
enable the radio or radios before the access point allows wireless associations from other devices. These
changes to the default configuration improve the security of newly installed access points.
Clients Using WPA/WPA2 and Power Save May Fail to Authenticate
Certain clients using WPA/WPA2 key management and power save can take many attempts to
authenticate or, in some cases, fail to authenticate. Any SSID that is defined to use authentication
key-management WPA, together with clients using power save mode and authenticating using
WPA/WPA2, can experience this problem.
A hidden configure level command, dot11 wpa handshake timeout, can be used to increase the timeout
between sending the WPA key packets from the default value (100 ms) to a value between 101 and 2000
ms. The command stores its value in the configuration across device reloads.
Release Notes for Cisco Aironet Access Points and Bridges for Cisco IOS Release 15.2(4)JB4
8
OL-30935-01
Important Notes
Default Username and Password Are Cisco
When you open the access point interface, you must enter a username and a password. The default
username for administrator login is Cisco, and the default password is Cisco. Both the username and
password are case sensitive.
Some Client Devices Cannot Associate When QoS Is Configured
Some wireless client devices, including Dell Axim handhelds and Hewlett-Packard iPaq HX4700
handhelds, cannot associate to an access point when the access point is configured for QoS. To allow
these clients to associate, disable QoS on the access point. You can use the QoS Policies page on the
access point GUI to disable QoS or enter this command on the CLI:
ap(config-if)# no dot11 qos mode
Some Devices Disassociate When Multiple BSSIDs Are Added or Deleted
Devices on your wireless LAN that are configured to associate to a specific access point based on the
access point MAC address (such as client devices, repeaters, hot standby units, or workgroup bridges)
might lose their association when you add or delete multiple BSSIDs. When you add or delete multiple
BSSIDs, check the association status of devices that are configured to associate to a specific access
point. If necessary, reconfigure the disassociated device to use the BSSID new MAC address.
Enabling MBSSIDs Without VLANs Disables Radio Interface
If you use the mbssid configuration interface command to enable multiple BSSIDs on a specific radio
interface but VLANs are not configured on the access point, the access point disables the radio interface.
To re-enable the radio, you must shut down the radio, disable multiple BSSIDs, and re-enable the radio.
This example shows how to re-enable the radio:
AP1260AG(config)# interface d1
AP1260AG(config-if)# shut
AP1260AG(config-if)# no mbssid
AP1260AG(config-if)# no shut
After you re-enable the radio, you can enable VLANs on the access point and enable multiple BSSIDs.
Cannot Set Channel on DFS-Enabled Radios in Some Regulatory Domains
Access points with 5-GHz radios configured at the factory for use in Europe, Singapore, Korea, Japan,
Taiwan, and Israel now comply with regulations that require radio devices to use Dynamic Frequency
Selection (DFS) to detect radar signals and to avoid interfering with them. You cannot manually set the
channel on DFS-enabled radios that are configured for these regulatory domains.
Release Notes for Cisco Aironet Access Points and Bridges for Cisco IOS Release 15.2(4)JB4
OL-30935-01
9
Important Notes
TACACS+ and DHCP IP Address Sometimes Locks Out Administrators
When you configure an access point for TACACS+ administration and you request for an IP address
from the DHCP server, you might be locked out of the access point after it reboots if you do not have a
local username and password configured on the access point. This issue does not affect access points that
are configured with a static IP address. If you have been locked out, you must regain access by resetting
the unit to default settings.
Access Points Do Not Support Loopback Interface
You must not configure a loopback interface on the access point.
Caution
Configuring a loopback interface might generate an IAPP GENINFO storm on your network and disrupt
network traffic.
Throughput Option for 802.11g Radio Blocks Association by 802.11b Clients
When you configure the 802.11g access point radio for best throughput, the access point sets all data
rates to basic (required). This setting blocks association from 802.11b client devices. The best
throughput option appears on the web-browser interface Express Setup and Radio Settings pages and
in the speed CLI configuration interface command.
Use Auto for Ethernet Duplex and Speed Settings
We recommend that you use auto, the default setting, for both the speed and duplex settings on the access
point Ethernet port. When your access point receives inline power from a switch, any change in the speed
or duplex settings that resets the Ethernet link reboots the access point. If the switch port to which the
access point is connected is not set to auto, you can change the access point port to half or full to correct
a duplex mismatch, and the Ethernet link is not reset. However, if you change from half or full back to
auto, the link is reset, and, if your access point receives inline power from a switch, the access point
reboots.
Note
The speed and duplex settings on the access point Ethernet port must match the Ethernet settings
on the port to which the access point is connected. If you change the settings on the port to which
the access point is connected, change the settings on the access point Ethernet port to match.
Using the force-reload Option with archive download-sw Command
When you upgrade an access point or bridge system software by entering the archive download-sw
command on the CLI, you must use the force-reload option. If the access point or bridge does not reload
the flash memory after the upgrade, the pages in the web-browser interface might not reflect the upgrade.
This example shows how to upgrade the system software by using the archive download-sw command:
AP# archive download-sw /force-reload /overwrite tftp://10.0.0.1/image-name
Release Notes for Cisco Aironet Access Points and Bridges for Cisco IOS Release 15.2(4)JB4
10
OL-30935-01
Important Notes
Radio MAC Address Appears in Access Point Event Log
When a client device roams from an access point (such as access point alpha) to another access point
(access point bravo), a message appears in the event log on access point alpha stating that the client
roamed to access point bravo. The MAC address that appears in the event message is the MAC address
for the radio in access point bravo. The MAC address for the access point Ethernet port is on the label
on the back of the access point.
Mask Field on IP Filters Page Behaves the Same As in CLI
In Cisco IOS Release 12.2(8)JA and later releases, the mask that you enter in the Mask field on the IP
Filters page in the access point GUI behaves the same way as a mask that you enter in the CLI. If you
enter 255.255.255.255 as the mask, the access point accepts any IP address. If you enter 0.0.0.0, the
access point looks for an exact match with the IP address that you entered in the IP Address field.
Repeater Access Points Cannot Be Configured as WDS Access Points
Repeater access points can participate in WDS, but they cannot provide WDS. You cannot configure a
repeater access point as a main WDS access point, and if a root access point becomes a repeater in
fallback mode, it cannot provide WDS.
Cannot Perform Link Tests on Non-Cisco Aironet Client Devices and on Cisco
Aironet 802.11g Client Devices
The link test feature on the web-browser interface does not support non-Cisco Aironet client devices.
Corrupt EAP Packet Sometimes Causes an Error Message
During client authentication, the access point sometimes receives a corrupt EAP packet and displays this
error message:
Oct 1 09:00:51.642 R: %SYS-2-GETBUF: Bad getbuffer, bytes= 28165
-Process= "Dot11 Dot1x process", ipl= 0, pid= 32
-Traceback= A2F98 3C441C 3C7184 3C604C 3C5E14 3C5430 124DDC
You can ignore this message.
When Cipher Is TKIP Only, Key Management Must Be Enabled
When you configure TKIP-only cipher encryption (not TKIP + WEP 128 or TKIP + WEP 40) on any
radio interface or VLAN, every SSID on that radio or VLAN must be set to use WPA or CCKM key
management. If you configure TKIP on a radio or VLAN but you do not configure key management on
the SSIDs, client authentication fails on the SSIDs.
Release Notes for Cisco Aironet Access Points and Bridges for Cisco IOS Release 15.2(4)JB4
OL-30935-01
11
Important Notes
Cisco CKM Supports SpectraLink Phones
Cisco CKM (CCKM) key management is designed to support voice clients that require minimal roaming
times. Voice clients must support Cisco Compatible Extensions to benefit from this feature, for the voice
client security mode you selected, please refer to the following URL for the list of CCX versions and
supported clients: http://www.cisco.com/web/partners/pr46/pr147/partners_pgm_concept_home.html
Non-Cisco Aironet Clients Sometimes Fail 802.1X Authentication
Some non-Cisco Aironet client adapters do not perform 802.1X authentication to the access point unless
you configure Open authentication with EAP. To allow both Cisco Aironet clients using LEAP and
non-Cisco Aironet clients using LEAP to associate using the same SSID, you might need to configure
the SSID for both Network EAP authentication and Open authentication with EAP.
Pings and Link Tests Sometimes Fail to Clients with Both Wired and Wireless
Network Connections
When you ping or run a link test from an access point to a client device installed in a PC running
Microsoft Windows, the ping or link test sometimes fails when the client has both wired and wireless
connections to the LAN. Microsoft does not recommend this configuration. For more information, refer
to Microsoft Knowledge Base article 157025 at this URL:
http://support.microsoft.com/default.aspx?scid=kb;en-us;157025&Product=win2000
Layer 3 Mobility Not Supported on Repeaters and Workgroup Bridges
Repeater access points and workgroup bridges cannot associate to an SSID that is configured for Layer
3 mobility. Layer 3 mobility is not supported on repeaters and workgroup bridges.
Hardware Limitation in Cisco Aironet 1250 and 1140 Series Access Points
The beacons on the Cisco Aironet 1250 and 1140 access points can only have output at intervals that are
multiples of 17 milliseconds. When these access points are configured for a 100-millisecond beacon
interval, they transmit beacons every 102 milliseconds. Similarly, when the beacon interval is configured
for 20 milliseconds, these access points transmit beacons every 17 milliseconds.
Potential RFC 3748 Violation
When the following command is configured under the SSID settings (for LEAP authentication):
authentication client username <WORD> password [0 | 7] <LINE>
if the first access-challenge returned by the Radius server after the access-request from the access point
is not for the LEAP method but for EAP-MD5, the access point violates RFC 3748.
Instead of sending an EAP NAK requesting LEAP authentication, the access point sends the user's
credentials with EAP-MD5 and drops the derived keys, since it cannot read the EAP-MD5 from the
access-accept.
Release Notes for Cisco Aironet Access Points and Bridges for Cisco IOS Release 15.2(4)JB4
12
OL-30935-01
Important Notes
This violates RFC 3748.
The workaround for this is to use the commands dot1x credentials and dot1x eap profile for LEAP
authentication.
For configuration procedures, see the Cisco IOS Software Configuration Guide for Cisco Aironet Access
Points.
Autonomous AP Will Treat The Sub-interface Tied To Bridge-group1 As The
Native Vlan
When using a configuration on an autonomous AP where there is no native VLAN defined, each
interface is being dot1q tagged, communication will fail after upgrading to release 15.2(4)JB4 or later.
It appears that the configuration is still correct after the upgrade, but the AP sends the untagged frames
for bridge-group 1, even though the encapsulation is not defined as native. The autonomous AP will treat
the sub-interface tied to bridge-group 1 as the native VLAN, even if it is not defined with the native
keyword: "encapsulation dot1 <vlan> native". The VLAN associated with bridge-group 1 must be set to
native on the connecting switchport configuration
The workaround for this is to configure VLAN 100 as the native VLAN on the connected switchport
trunk, even though the encapsulation is not specified as native on the AP.
DHCP Failure When Access Point Renewal Time Is Greater Than Rebind Time
An access point is unable to obtain IP through the same IOS DHCP server when the access point is
running on 15.2x. The problem occurs because the Renewal (T1) time dhcp option 58 is larger than
Rebinding (T2) time dhcp option 59.
Configuring the radius server using the old cli
This cli command was used in the previous releases to configure radius servers:
radius-server host {hostname | ip-address} [auth-port port-number] [acct-port port-number]
[timeout seconds] [retransmit retries] [key string]
Though this command can still be used, we recommend that you use this new command:
radius server {server-name}[auth-port port-number] [acct-port port-number] [timeout seconds]
[retransmit retries] [key string]
Upgrade from IOS 12.4 to IOS 15 breaks access point L3 Connectivity
The following table shows the behavior change:
Release Notes for Cisco Aironet Access Points and Bridges for Cisco IOS Release 15.2(4)JB4
OL-30935-01
13
Caveats
Release Name
IP Routing Enabled
Action to be Taken Before
Upgrade to Cisco IOS Release
15.2(4)JB4
Till Cisco IOS Release
15.2(2)JA
Not Applicable
No issue in upgrade.
Cisco IOS Release 15.2(2)JB
No
Cisco IOS Release 15.2(4)JA
Yes
IP routing and configured routes
should be removed and default
gateway should be configured if
required.
Caveats
This section lists Open Caveats and Resolved Caveats for access points and bridges in Cisco IOS Release
15.2(4)JB4.
Cisco Bug Search Tool
The Bug Search Tool (BST), which is the online successor to Bug Toolkit, is designed to improve the
effectiveness in network risk management and device troubleshooting. The BST allows partners and
customers to search for software bugs based on product, release, and keyword, and aggregates key data
such as bug details, product, and version. The tool has a provision to filter bugs based on credentials to
provide external and internal bug views for the search input.
To view the details of a caveat listed in this document:
1.
Access the BST (use your Cisco user ID and password) at https://tools.cisco.com/bugsearch/.
2.
Enter the bug ID in the Search For: field.
Open Caveats
Table 3 lists caveats that are open in Cisco IOS Release 15.2(4)JB4.
Table 3
Open Caveats
Identifier
Headline
CSCud51131
Need new CLI to configure IPv6 SNTP server addresses.
CSCue53185
The allowed frequencies are repeated in show controllers dot111 command for Japan
regdomain.
CSCuf85579
Multicast downstream fails on a wlan client with security wpa2-tkip on enabling broadcast key
rotation.
CSCui79550
The IP Protocol 119 column is missing on the QoS policies page.
CSCuj62328
The Apple client does not associate with 11r SSID.
Release Notes for Cisco Aironet Access Points and Bridges for Cisco IOS Release 15.2(4)JB4
14
OL-30935-01
Troubleshooting
Table 3
Open Caveats
Identifier
Headline
CSCum95814
Authorization fails for 1042 AAA-3-AUTH_LOW_IOMEM clients while using IPv6.
CSCul91975
WGB may disconnect permanently after 802.11 probe.
CSCuo69578
Cisco AP1532 bridge throughput is very low on 802.11n.
Resolved Caveats
Table 4 lists caveats that are resolved in Cisco IOS Release 15.2(4)JB4.
Table 4
Resolved Caveats
Identifier
Headline
CSCum68243
The dot11 ant-band-mode command is not available.
CSCum50818
The 1552 IOS crashes when configured in the non root bridge mode.
CSCum16566
When 1532I is powered in C, E, H, M and S domains, with 802.3at PoE+ or AIR-PWRINJ4 power
injector, one of the 2.4GHz TX is disabled.
CSCum49200
Wireless clients utilizing Broadcom chipsets may have trouble associating to a Cisco Aironet 2600 or
3600 series access points.
CSCun02785
Add new 5G CTL tables for D-domain for both Cisco Aironet 1532i and 1532e access points.
If You Need More Information
If you need information about a specific caveat that does not appear in these release notes, you can use
the Cisco Bug Toolkit to find select caveats of any severity. Click this URL to browse to the Bug Toolkit:
https://tools.cisco.com/bugsearch/search
(If you request a defect that cannot be displayed, the defect number might not exist, the defect might not
yet have a customer-visible description, or the defect might be marked Cisco Confidential.)
Troubleshooting
For the most up-to-date, detailed troubleshooting information, refer to the Cisco TAC website at
http://www.cisco.com/cisco/web/support/index.html. Click Technology Support, choose Wireless
from the menu on the left, and click Wireless LAN.
Release Notes for Cisco Aironet Access Points and Bridges for Cisco IOS Release 15.2(4)JB4
OL-30935-01
15
Obtaining Documentation, Obtaining Support, and Security Guidelines
Obtaining Documentation, Obtaining Support, and Security
Guidelines
For information on obtaining documentation, obtaining support, providing documentation feedback,
security guidelines, and also recommended aliases and general Cisco documents, see the monthly
What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical
documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of
Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The
use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)
Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and
figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and
coincidental.
Copyright © 2013 Cisco Systems, Inc. All rights reserved.
Release Notes for Cisco Aironet Access Points and Bridges for Cisco IOS Release 15.2(4)JB4
16
OL-30935-01
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement