Mitsubishi GT1000 GT14-U-E graphic operation terminal User's Manual

SAFETY PRECAUTIONS
(Always read these precautions before using this equipment.)
Before using this product, please read this manual and the relevant manuals introduced in this manual
carefully and pay full attention to safety to handle the product correctly.
The precautions given in this manual are concerned with this product.
In this manual, the safety precautions are ranked as "WARNING" and "CAUTION".
WARNING
Indicates that incorrect handling may cause hazardous conditions,
resulting in death or severe injury.
CAUTION
Indicates that incorrect handling may cause hazardous conditions,
resulting in medium or slight personal injury or physical damage.
Note that the
caution level may lead to a serious accident according to the circumstances.
Always follow the instructions of both levels because they are important to personal safety.
Please save this manual to make it accessible when required and always forward it to the end user.
[DESIGN PRECAUTIONS]
WARNING
● Some failures of the GOT, communication unit or cable may keep the outputs on or off.
Some failures of a touch panel may cause malfunction of the input objects such as a touch switch.
An external monitoring circuit should be provided to check for output signals which may lead to a
serious accident.
Not doing so can cause an accident due to false output or malfunction.
● If a communication fault (including cable disconnection) occurs during monitoring on the GOT,
communication between the GOT and PLC CPU is suspended and the GOT becomes inoperative.
A system where the GOT is used should be configured to perform any significant operation to the
system by using the switches of a device other than the GOT on the assumption that a GOT
communication fault will occur.
Not doing so can cause an accident due to false output or malfunction.
● Do not use the GOT as the warning device that may cause a serious accident.
An independent and redundant hardware or mechanical interlock is required to configure the device
that displays and outputs serious warning.
Failure to observe this instruction may result in an accident due to incorrect output or malfunction.
● Incorrect operation of the touch switch(s) may lead to a serious accident if the GOT backlight is gone
out.
When the GOT backlight goes out, the POWER LED blinks (green/orange) and the display section
dims, while the input of the touch switch(s) remains active.
This may confuse an operator in thinking that the GOT is in "screensaver" mode, who then tries to
release the GOT from this mode by touching the display section, which may cause a touch switch to
operate.
Note that the following occurs on the GOT when the backlight goes out.
• The POWER LED flickers (green/orange) and the monitor screen appears blank.
A-1
[DESIGN PRECAUTIONS]
WARNING
● The display section is an analog-resistive type touch panel.
If you touch the display section simultaneously in 2 points or more, the switch that is located around
the center of the touched point, if any, may operate.
Do not touch the display section in 2 points or more simultaneously.
Doing so may cause an accident due to incorrect output or malfunction.
● When programs or parameters of the controller (such as a PLC) that is monitored by the GOT are
changed, be sure to reset the GOT or shut off the power of the GOT at the same time.
Not doing so can cause an accident due to false output or malfunction.
CAUTION
● Do not bundle the control and communication cables with main-circuit, power or other wiring.
Run the above cables separately from such wiring and keep them a minimum of 100mm apart.
Not doing so noise can cause a malfunction.
● Do not press the GOT display section with a pointed material as a pen or driver.
Doing so can result in a damage or failure of the display section.
● When the GOT is connected to the Ethernet network, the available IP address is restricted according
to the system configuration.
• When multiple GOTs are connected to the Ethernet network:
Do not set the IP address (192.168.0.18) for the GOTs and the controllers in the network.
• When a single GOT is connected to the Ethernet network:
Do not set the IP address (192.168.0.18) for the controllers except the GOT in the network.
Doing so can cause the IP address duplication. The duplication can negatively affect the
communication of the device with the IP address (192.168.0.18).
The operation at the IP address duplication depends on the devices and the system.
● Turn on the controllers and the network devices to be ready for communication before they
communicate with GOT.
Failure to do so can cause a communication error on the GOT.
[MOUNTING PRECAUTIONS]
WARNING
● Be sure to shut off all phases of the external power supply used by the system before mounting or
removing the GOT to/from the panel.
Not switching the power off in all phases can cause a unit failure or malfunction.
A-2
[MOUNTING PRECAUTIONS]
CAUTION
● Use the GOT in the environment that satisfies the general specifications described in the User's
Manual.
Not doing so can cause an electric shock, fire, malfunction or product damage or deterioration.
● When mounting the GOT to the panel, tighten the mounting screws within the specified torque range.
Undertightening can cause the GOT to drop, short or malfunction. Also, undertightening can disable
waterproof or oil proof effect.
Overtightening can cause a drop, short circuit or malfunction due to the damage of the screws or the
GOT.
Also, "distortion" of the GOT or the panel may disable waterproof or oil proof effect.
● Never drop cutting chips and electric wire chips into the ventilation window of the GOT when you drill
screw holes or perform wiring.
Otherwise, fire, failure or malfunction may be caused.
● When inserting/removing a SD card into/from the GOT, turn the SD card access switch off in
advance.
Failure to do so may corrupt data within the SD card.
● When removing a SD card from the GOT, make sure to support the SD card by hand, as it may pop
out.
Failure to do so may cause the SD card to drop from the GOT and break.
● When installing a USB memory to the GOT, make sure to install the USB memory to the USB
interface firmly.
Failure to do so may cause a malfunction due to poor contact.
● Before removing the USB memory from the GOT, operate the utility screen for removal.
After the successful completion dialog box is displayed, remove the memory by hand carefully.
Failure to do so may cause the USB memory to drop, resulting in a damage or failure of the memory.
● Operate and store the GOT in environments without direct sunlight, high temperature, dust, humidity,
and vibrations.
● When using the GOT in the environment of oil or chemicals, use the protective cover for oil.
Failure to do so may cause failure or malfunction due to the oil or chemical entering into the GOT.
A-3
[WIRING PRECAUTIONS]
WARNING
● Be sure to shut off all phases of the external power supply used by the system before wiring.
Failure to do so may result in an electric shock, product damage or malfunctions.
● Always ground the FG terminal of the GOT power to the protective ground conductors dedicated to
the GOT.
Not doing so may cause an electric shock or malfunction.
● Correctly wire the GOT power supply section after confirming the rated voltage and terminal
arrangement of the product.
Not doing so can cause a fire or failure.
● Tighten the terminal screws of the GOT power supply section in the specified torque range.
Undertightening can cause a short circuit or malfunction.
Overtightening can cause a short circuit or malfunction due to the damage of the screws or the GOT.
● Exercise care to avoid foreign matter such as chips and wire offcuts entering the GOT.
Not doing so can cause a fire, failure or malfunction.
CAUTION
● The cables connected to the unit must be run in ducts or clamped.
Not doing so can cause the unit or cable to be damaged due to the dangling, motion or accidental
pulling of the cables or can cause a malfunction due to a cable connection fault.
● When unplugging the cable connected to the unit, do not hold and pull the cable portion.
Doing so can cause the unit or cable to be damaged or can cause a malfunction due to a cable
connection fault.
● Plug the communication cable into the connector of the connected unit and tighten the mounting and
terminal screws in the specified torque range.
Undertightening can cause a short circuit or malfunction. Overtightening can cause a short circuit or
malfunction due to the damage of the screws or unit.
[TEST OPERATION PRECAUTIONS]
WARNING
● Before performing the test operations of the user creation monitor screen (such as turning ON or
OFF bit device, changing the word device current value, changing the settings or current values of
the timer or counter, and changing the buffer memory current value), read through the manual
carefully and make yourself familiar with the operation method.
During test operation, never change the data of the devices which are used to perform significant
operation for the system.
False output or malfunction can cause an accident.
A-4
[STARTUP/MAINTENANCE PRECAUTIONS]
WARNING
● When power is on, do not touch the terminals.
Doing so can cause an electric shock or malfunction.
● Correctly connect the battery connector.
Do not charge, disassemble, heat, short-circuit, solder, or throw the battery into the fire.
Doing so will cause the battery to produce heat, explode, or ignite, resulting in injury and fire.
● Before starting cleaning or terminal screw retightening, always switch off the power externally in all
phases.
Not switching the power off in all phases can cause a unit failure or malfunction.
Undertightening can cause a short circuit or malfunction.
Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit.
CAUTION
● Do not disassemble or modify the unit.
Doing so can cause a failure, malfunction, injury or fire.
● Do not touch the conductive and electronic parts of the unit directly.
Doing so can cause a unit malfunction or failure.
● Do not drop or apply strong impact to the unit.
Doing so may damage the unit.
● Do not drop or give an impact to the battery mounted to the unit.
Doing so may damage the battery, causing the battery fluid to leak inside the battery.
If the battery is dropped or given an impact, dispose of it without using.
● For repair of the backlight, contact your local Mitsubishi (Electric System) Service.
● Before touching the unit, always touch grounded metal, etc. to discharge static electricity from
human body, etc.
Not doing so can cause the unit to fail or malfunction.
● Replace battery with GT11-50BAT by Mitsubishi electric Co. only.
Use of another battery may present a risk of fire or explosion.
● Dispose of used battery promptly.
Keep away from children. Do not disassemble and do not dispose of in fire.
A-5
[DISPOSAL PRECAUTIONS]
CAUTION
● When disposing of the product, handle it as industrial waste.
● When disposing of this product, treat it as industrial waste. When disposing of batteries, separate
them from other wastes according to the local regulations.
(For details of the battery directive in EU member states, refer to the User's Manual of the GOT to be
used.)
[TOUCH PANEL PRECAUTIONS]
CAUTION
● For the analog-resistive film type touch panels, normally the adjustment is not required. However,
the difference between a touched position and the object position may occur as the period of use
elapses. When any difference between a touched position and the object position occurs, execute
the touch panel calibration.
● When any difference between a touched position and the object position occurs, other object may be
activated. This may cause an unexpected operation due to incorrect output or malfunction.
[TRANSPORTATION PRECAUTIONS]
CAUTION
● When transporting lithium batteries, make sure to treat them based on the transport regulations.
(For details on models subject to restrictions, refer to the User's Manual for the GOT you are using.)
● Before transporting the GOT, turn the GOT power on and check that the battery voltage status is
normal on the Time setting & display screen (utilities screen). In addition, confirm that the adequate
battery life remains on the rating plate.
Transporting the GOT with the low battery voltage or the battery the reached battery life may
unstabilize the backup data unstable during transportation.
● Make sure to transport the GOT main unit and/or relevant unit(s) in the manner they will not be
exposed to the impact exceeding the impact resistance described in the general specifications of the
User's Manual, as they are precision devices.
Failure to do so may cause the unit to fail.
Check if the unit operates correctly after transportation.
A-6
INTRODUCTION
Thank you for choosing Mitsubishi Graphic Operation Terminal (Mitsubishi GOT).
Read this manual and make sure you understand the functions and performance of the GOT thoroughly
in advance to ensure correct use.
CONTENTS
SAFETY PRECAUTIONS .........................................................................................................................A - 1
INTRODUCTION ......................................................................................................................................A - 7
CONTENTS ..............................................................................................................................................A - 7
MANUALS...............................................................................................................................................A - 13
QUICK REFERENCE .............................................................................................................................A - 13
ABBREVIATIONS AND GENERIC TERMS ...........................................................................................A - 15
HOW TO READ THIS MANUAL .............................................................................................................A - 20
1. OVERVIEW
1.1
Features........................................................................................................................................... 1 - 2
1.1.1 Rough procedure .................................................................................................................. 1 - 3
2. SYSTEM CONFIGURATION
2.1
Overall Configuration ....................................................................................................................... 2 - 1
2.2
System Equipment........................................................................................................................... 2 - 1
2.2.1 GOT (GT14) ......................................................................................................................... 2 - 2
2.2.2 Option ................................................................................................................................... 2 - 3
3. SPECIFICATIONS
3.1
General Specifications..................................................................................................................... 3 - 1
3.2
Performance Specifications ............................................................................................................. 3 - 2
3.3
Power Supply Specifications ........................................................................................................... 3 - 3
4. PARTS NAME
4.1
Front Panel ...................................................................................................................................... 4 - 1
4.2
Back Panel....................................................................................................................................... 4 - 2
4.3
Rear Face ........................................................................................................................................ 4 - 3
5. UL, cUL STANDARDS AND EMC DIRECTIVE
5.1
UL, cUL Standards .......................................................................................................................... 5 - 1
5.2
EMC Directive.................................................................................................................................. 5 - 1
5.2.1 Requirements to Meet EMC Directive .................................................................................. 5 - 2
5.2.2 EMC Directive-Compliant System Configuration .................................................................. 5 - 4
5.2.3 Precautions for Wiring/Connecting the EMC Directive-Compliant Product .......................... 5 - 5
A-7
6. INSTALLATION
6.1
Control Panel Inside Dimensions for Mounting GOT ....................................................................... 6 - 1
6.2
Panel Cutting Dimension ................................................................................................................. 6 - 2
6.3
Mounting Position ............................................................................................................................ 6 - 2
6.4
Control Panel Temperature and Mounting Angle ............................................................................ 6 - 3
6.5
Installation Procedure ...................................................................................................................... 6 - 4
7. WIRING
7.1
Power Supply Wiring ....................................................................................................................... 7 - 2
7.1.1 Wiring example ..................................................................................................................... 7 - 2
7.1.2 Grounding the GOT .............................................................................................................. 7 - 2
7.1.3 The cause of malfunctions related wiring/Remedy ............................................................... 7 - 3
7.2
Wiring inside and outside the panel ................................................................................................. 7 - 5
7.2.1 Wiring inside ......................................................................................................................... 7 - 5
7.2.2 Outside the panel.................................................................................................................. 7 - 5
7.2.3 Attaching surge killers to control equipment ......................................................................... 7 - 6
8. OPTION
A-8
8.1
SD Card ........................................................................................................................................... 8 - 1
8.1.1 Applicable SD card ............................................................................................................... 8 - 1
8.1.2 Installing and removing procedures of the SD card.............................................................. 8 - 1
8.2
USB Memory ................................................................................................................................... 8 - 3
8.2.1 Applicable USB memory....................................................................................................... 8 - 3
8.2.2 Installing and removing procedures of the USB memory ..................................................... 8 - 3
8.3
Battery ............................................................................................................................................. 8 - 4
8.3.1 Applicable battery ................................................................................................................. 8 - 4
8.3.2 Battery specifications............................................................................................................ 8 - 4
8.3.3 Battery replacement procedure ............................................................................................ 8 - 5
8.4
Protective Sheet .............................................................................................................................. 8 - 6
8.4.1 Applicable protective sheet................................................................................................... 8 - 6
8.4.2 Installing procedure .............................................................................................................. 8 - 6
8.5
Protective Cover for Oil.................................................................................................................... 8 - 7
8.5.1 Applicable protective cover for oil ......................................................................................... 8 - 7
8.5.2 Installing procedure .............................................................................................................. 8 - 7
8.6
USB Environmental Protection Cover.............................................................................................. 8 - 9
8.6.1 Applicable USB environmental protection cover................................................................... 8 - 9
8.6.2 Installing procedure .............................................................................................................. 8 - 9
8.7
Stand ............................................................................................................................................. 8 - 10
8.7.1 Applicable stand ................................................................................................................. 8 - 10
8.7.2 Installing procedure ............................................................................................................ 8 - 10
8.8
Connector Conversion Adapter ..................................................................................................... 8 - 11
8.8.1 Applicable connector conversion adapter........................................................................... 8 - 11
8.8.2 Installing procedure of connector conversion adapter ........................................................ 8 - 11
8.9
Serial Multi-Drop Connection Unit.................................................................................................. 8 - 12
8.9.1 Serial multi-drop connection unit ........................................................................................ 8 - 12
8.9.2 Applicable serial multi-drop connection unit ....................................................................... 8 - 12
8.9.3 Installation........................................................................................................................... 8 - 12
8.9.4
8.9.5
Parts name ......................................................................................................................... 8 - 13
Caution for compliance with EMC Directive........................................................................ 8 - 13
8.10 Panel-Mounted USB Port Extension.............................................................................................. 8 - 14
8.10.1 Applicable panel-mounted USB port extension .................................................................. 8 - 14
8.10.2 Parts name ......................................................................................................................... 8 - 14
8.10.3 Installing procedure ............................................................................................................ 8 - 14
8.11 RS-232/485 Signal Conversion Adapter........................................................................................ 8 - 16
8.11.1 Applicable RS-232/485 signal conversion adapter ............................................................. 8 - 16
8.11.2 Installing procedure of RS-232/485 signal conversion adapter .......................................... 8 - 16
9. UTILITY FUNCTION
9.1
Utility Execution ............................................................................................................................... 9 - 1
9.2
Utility Function List........................................................................................................................... 9 - 2
9.3
Utility Display ................................................................................................................................... 9 - 4
9.3.1 Display operation of main menu ........................................................................................... 9 - 6
9.3.2 Utility basic configuration ...................................................................................................... 9 - 8
9.3.3 Basic operation of settings change....................................................................................... 9 - 9
10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)
10.1
Communication setting .................................................................................................................. 10 - 1
10.1.1 Communication setting functions........................................................................................ 10 - 1
10.1.2 Display operation of Communication Setting...................................................................... 10 - 1
10.1.3 Communication setting contents ........................................................................................ 10 - 2
10.1.4 Communication setting operation ....................................................................................... 10 - 4
10.2
Communication Detail Setting ....................................................................................................... 10 - 8
10.2.1 Communication detail setting functions .............................................................................. 10 - 8
10.2.2 Display operation of Communication Detail setting ............................................................ 10 - 8
10.2.3 Display contents of Communication Detail setting............................................................ 10 - 10
10.3
Ethernet Setting ........................................................................................................................... 10 - 15
10.3.1 Ethernet setting functions ................................................................................................. 10 - 15
10.3.2 Display operation of Ethernet setting................................................................................ 10 - 15
10.3.3 Display contents of Ethernet setting ................................................................................. 10 - 16
11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)
11.1
Display Setting............................................................................................................................... 11 - 1
11.1.1 Function of Display ............................................................................................................. 11 - 1
11.1.2 Display operation of Display ............................................................................................... 11 - 2
11.1.3 Display operations .............................................................................................................. 11 - 3
11.2
Operation Setting (Settings Regarding Operation) ........................................................................ 11 - 6
11.2.1 Operation setting functions ................................................................................................. 11 - 6
11.2.2 Display operation of Operation ........................................................................................... 11 - 7
11.2.3 Setting operation of operation ............................................................................................ 11 - 8
11.2.4 Security level change ......................................................................................................... 11 - 9
11.2.5 Utility Call Key Setting ...................................................................................................... 11 - 11
11.2.6 Adjusting the touch panel position (Touch panel calibration) ........................................... 11 - 13
11.2.7 USB mouse/keyboard setting ........................................................................................... 11 - 15
11.2.8 VNC(R) server function setting ......................................................................................... 11 - 17
11.3
Transparent Mode Setting ........................................................................................................... 11 - 18
11.4
Backup/Restoration Setting ......................................................................................................... 11 - 19
A-9
11.5
Behavior of Duplicate IPs ............................................................................................................ 11 - 22
11.6
License Management .................................................................................................................. 11 - 25
12. CLOCK SETTINGS AND BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12.1
Time Setting and Display ............................................................................................................... 12 - 1
12.1.1 Time setting and display functions...................................................................................... 12 - 1
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.1
Data Storage Location ................................................................................................................... 13 - 1
13.1.1 Data type and storage location ........................................................................................... 13 - 1
13.1.2 OS version confirmation ..................................................................................................... 13 - 3
13.1.3 Capacity confirmation of the project data downloading location......................................... 13 - 4
13.1.4 Display file .......................................................................................................................... 13 - 4
13.2
Various Data Control ..................................................................................................................... 13 - 5
13.2.1 OS information.................................................................................................................... 13 - 5
13.2.2 Alarm information.............................................................................................................. 13 - 11
13.2.3 Project Information............................................................................................................ 13 - 17
13.2.4 Hard copy information....................................................................................................... 13 - 27
13.2.5 Advanced recipe information ............................................................................................ 13 - 33
13.2.6 Logging information .......................................................................................................... 13 - 53
13.2.7 Memory card format.......................................................................................................... 13 - 63
13.2.8 Memory information .......................................................................................................... 13 - 65
13.2.9 USB device status display ................................................................................................ 13 - 66
13.2.10 SRAM control.................................................................................................................... 13 - 68
13.2.11 GOT data package acquisition ......................................................................................... 13 - 73
13.2.12 Operator information management................................................................................... 13 - 74
14. GOT SELF CHECK (DEBUG AND SELF CHECK)
14.1
Debug ............................................................................................................................................ 14 - 1
14.1.1 System monitor................................................................................................................... 14 - 1
14.1.2 A list editor .......................................................................................................................... 14 - 1
14.1.3 FX list editor........................................................................................................................ 14 - 1
14.1.4 Backup/restoration.............................................................................................................. 14 - 2
14.2
Self Check ..................................................................................................................................... 14 - 3
14.2.1 Memory check .................................................................................................................... 14 - 3
14.2.2 Drawing check .................................................................................................................... 14 - 6
14.2.3 Font check ........................................................................................................................ 14 - 10
14.2.4 Touch panel check............................................................................................................ 14 - 12
14.2.5 I/O check........................................................................................................................... 14 - 14
14.2.6 Ethernet status check ....................................................................................................... 14 - 17
14.3
System Alarm Display.................................................................................................................. 14 - 19
14.4
GOT start time ............................................................................................................................. 14 - 21
15. CLEANING DISPLAY SECTION (CLEAN)
16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS
16.1
BootOS and Standard Monitor OS Required for Installation.......................................................... 16 - 2
16.2
Prior Preparations for Installing BootOS and Standard Monitor OS .............................................. 16 - 3
A - 10
16.3
BootOS and Standard Monitor OS Installation Using SD card or USB Memory ........................... 16 - 4
16.3.1 Installing when starting the GOT ........................................................................................ 16 - 5
16.3.2 Installing using the program/data control function (Utility) .................................................. 16 - 7
16.4
When Installing the Different Version of BootOS, Standard Monitor OS ....................................... 16 - 9
16.5
CoreOS........................................................................................................................................ 16 - 11
16.5.1 Installing the CoreOS ....................................................................................................... 16 - 11
16.5.2 When the CoreOS cannot be installed ............................................................................. 16 - 13
17. MAINTENANCE AND INSPECTION
17.1
Daily Inspection ............................................................................................................................. 17 - 2
17.2
Periodic Inspection ........................................................................................................................ 17 - 2
17.3
Cleaning Method............................................................................................................................ 17 - 3
17.4
Battery Voltage Low Detection and Battery Replacement............................................................. 17 - 4
17.5
Backlight Shutoff Detection............................................................................................................ 17 - 7
17.5.1 Backlight shutoff detection and external alarm ................................................................... 17 - 7
18. TROUBLESHOOTING
18.1
GOT Restoration Sheet ................................................................................................................. 18 - 1
18.2
Error Message and System Alarm............................................................................................... 18 - 11
18.2.1 Error contents display ....................................................................................................... 18 - 11
18.2.2 List of error message/system alarm.................................................................................. 18 - 13
APPENDICES
Appendix.1
External Dimensions..........................................................................................................App - 1
Appendix.2
Usage Condition of Utility Function ...................................................................................App - 7
Appendix.3 Transportation Precautions ...............................................................................................App - 9
Appendix.3.1 Relevant models...........................................................................................................App - 9
Appendix.3.2 Transportation guidelines .............................................................................................App - 9
INDEX
REVISIONS
A - 11
A - 12
MANUALS
The following table lists the manual relevant to this product.
Refer to each manual for any purpose.
Packaging
Manual Number
(Model code)
GT Works3 Version1 Installation Procedure Manual
Enclosed in product
-
GT Designer3 Version1 Screen Design Manual (Fundamentals) 1/2, 2/2
Stored in CD-ROM
SH-080866ENG
(1D7MB9)
GT Designer3 Version1 Screen Design Manual (Functions) 1/2, 2/2
Stored in CD-ROM
SH-080867ENG
(1D7MC1)
GOT1000 Series Connection Manual (Mitsubishi Products) for GT Works3
Stored in CD-ROM
SH-080868ENG
(1D7MC2)
GOT1000 Series Connection Manual (Non-Mitsubishi Products 1) for GT Works3
Stored in CD-ROM
SH-080869ENG
(1D7MC3)
GOT1000 Series Connection Manual (Non-Mitsubishi Products 2) for GT Works3
Stored in CD-ROM
SH-080870ENG
(1D7MC4)
GOT1000 Series Connection Manual (Microcomputer, MODBUS Products, Peripherals) for GT
Works3
Stored in CD-ROM
SH-080871ENG
(1D7MC5)
GT Simulator3 Version1 Operating Manual for GT Works3
Stored in CD-ROM
SH-080861ENG
(1D7MB1)
GOT1000 Series User's Manual (Extended Functions, Option Functions) for GT Works3
Stored in CD-ROM
SH-080863ENG
(1D7MB3)
Manual Name
QUICK REFERENCE
 Creating a project
Obtaining the specifications and operation methods of GT Designer3
Setting available functions on GT Designer3
Creating a screen displayed on the GOT
GT Designer3 Version1 Screen Design Manual
(Fundamentals) 1/2, 2/2
Obtaining useful functions to increase efficiency of drawing
Setting details for figures and objects
Setting functions for the data collection or trigger action
GT Designer3 Version1 Screen Design Manual (Functions)
1/2, 2/2
Setting functions to use peripheral devices
Simulating a created project on a personal computer
GT Simulator3 Version1 Operating Manual for GT Works3
 Connecting a controller to the GOT
Obtaining information of Mitsubishi products applicable to the GOT
Connecting Mitsubishi products to the GOT
Connecting multiple controllersto one GOT (Multi-channel function)
GOT1000 Series Connection Manual (Mitsubishi Products)
for GT Works3
Establishing communication between a personal computer and a
controller via the GOT (FA transparent function)
A - 13
Obtaining information of Non-Mitsubishi products applicable to the
GOT
Connecting Non-Mitsubishi products to the GOT
Obtaining information of peripheral devices applicable to the GOT
Connecting peripheral devices including a barcode reader to the GOT
• GOT1000 Series Connection Manual (Non-Mitsubishi
Products 1) for GT Works3
• GOT1000 Series Connection Manual (Non-Mitsubishi
Products 2) for GT Works3
GOT1000 Series Connection Manual (Microcomputer,
MODBUS Products, Peripherals) for GT Works3
 Transferring data to the GOT
Writing data to the GOT
Reading data from the GOT
GT Designer3 Version1 Screen Design Manual
(Fundamentals) 1/2, 2/2
Verifying a editing project to a GOT project
 Others
Configuring the extended function and option function
A - 14
GOT1000 Series User's Manual (Extended Functions, Option
Functions) for GT Works3
ABBREVIATIONS AND GENERIC TERMS
 GOT
Abbreviations and generic terms
GT1695M-X
Abbreviation of GT1695M-XTBA, GT1695M-XTBD
GT1685
GT1685M-S
Abbreviation of GT1685M-STBA, GT1685M-STBD
GT1675M-S
Abbreviation of GT1675M-STBA, GT1675M-STBD
GT1675M-V
Abbreviation of GT1675M-VTBA, GT1675M-VTBD
GT1675-VN
Abbreviation of GT1675-VNBA, GT1675-VNBD
GT1672-VN
Abbreviation of GT1672-VNBA, GT1672-VNBD
GT1665M-S
Abbreviation of GT1665M-STBA, GT1665M-STBD
GT1675
GT1672
GT1665
GT1665M-V
Abbreviation of GT1665M-VTBA, GT1665M-VTBD
GT1662
GT1662-VN
Abbreviation of GT1662-VNBA, GT1662-VNBD
GT1655
GT1655-V
Abbreviation of GT1655-VTBD
GT1595-X
Abbreviation of GT1595-XTBA, GT1595-XTBD
GT16
GT1595
GT1585
GT157
GT156
GOT1000
Series
Description
GT1695
GT155
Abbreviation of GT1695, GT1685, GT1675, GT1672, GT1665, GT1662, GT1655, GT16 Handy GOT
GT1585V-S
Abbreviation of GT1585V-STBA, GT1585V-STBD
GT1585-S
Abbreviation of GT1585-STBA, GT1585-STBD
GT1575V-S
Abbreviation of GT1575V-STBA, GT1575V-STBD
GT1575-S
Abbreviation of GT1575-STBA, GT1575-STBD
GT1575-V
Abbreviation of GT1575-VTBA, GT1575-VTBD
GT1575-VN
Abbreviation of GT1575-VNBA, GT1575-VNBD
GT1572-VN
Abbreviation of GT1572-VNBA, GT1572-VNBD
GT1565-V
Abbreviation of GT1565-VTBA, GT1565-VTBD
GT1562-VN
Abbreviation of GT1562-VNBA, GT1562-VNBD
GT1555-V
Abbreviation of GT1555-VTBD
GT1555-Q
Abbreviation of GT1555-QTBD, GT1555-QSBD
GT1550-Q
Abbreviation of GT1550-QLBD
GT15
GT145
Abbreviation of GT1595, GT1585, GT157 , GT156 , GT155
GT1455-Q
Abbreviation of GT1455-QTBDE, GT1455-QTBD
GT1450-Q
Abbreviation of GT1450-QLBDE, GT1450-QLBD
GT14
Abbreviation of GT1455-Q, GT1450-Q
GT1275
GT1275-V
Abbreviation of GT1275-VNBA, GT1275-VNBD
GT1265
GT1265-V
Abbreviation of GT1265-VNBA, GT1265-VNBD
GT12
GT115
Abbreviation of GT1275, GT1265
GT1155-Q
GT1150-Q
GT11
GT105
GT104
Abbreviation of GT1155-QTBDQ, GT1155-QSBDQ, GT1155-QTBDA, GT1155-QSBDA,
GT1155-QTBD, GT1155-QSBD
Abbreviation of GT1150-QLBDQ, GT1150-QLBDA, GT1150-QLBD
Abbreviation of GT115 , GT11 Handy GOT,
GT1055-Q
Abbreviation of GT1055-QSBD
GT1050-Q
Abbreviation of GT1050-QBBD
GT1045-Q
Abbreviation of GT1045-QSBD
GT1040-Q
Abbreviation of GT1040-QBBD
GT1030
Abbreviation of GT1030-LBD, GT1030-LBD2, GT1030-LBL, GT1030-LBDW, GT1030-LBDW2,
GT1030-LBLW, GT1030-LWD, GT1030-LWD2, GT1030-LWL, GT1030-LWDW, GT1030-LWDW2,
GT1030-LWLW, GT1030-HBD, GT1030-HBD2, GT1030-HBL, GT1030-HBDW, GT1030-HBDW2,
GT1030-HBLW, GT1030-HWD, GT1030-HWD2, GT1030-HWL, GT1030-HWDW, GT1030-HWDW2,
GT1030-HWLW
GT1020
Abbreviation of GT1020-LBD, GT1020-LBD2, GT1020-LBL, GT1020-LBDW, GT1020-LBDW2,
GT1020-LBLW, GT1020-LWD, GT1020LWD2, GT1020-LWL, GT1020-LWDW, GT1020-LWDW2,
GT1020-LWLW
GT10
Abbreviation of GT105 , GT104 , GT1030, GT1020
A - 15
Abbreviations and generic terms
GOT1000
Series
GT16
Handy
GOT
Handy
GOT
GT11
Handy
GOT
Description
GT1665HS-V
Abbreviation of GT1665HS-VTBD
GT1155HS-Q
Abbreviation of GT1155HS-QSBD
GT1150HS-Q
Abbreviation of GT1150HS-QLBD
GT SoftGOT1000
Abbreviation of GT SoftGOT1000
GOT900 Series
Abbreviation of GOT-A900 series, GOT-F900 series
GOT800 Series
Abbreviation of GOT-800 series
 Communication unit
Abbreviations and generic terms
Description
Bus connection unit
GT15-QBUS, GT15-QBUS2, GT15-ABUS, GT15-ABUS2, GT15-75QBUSL, GT15-75QBUS2L,
GT15-75ABUSL, GT15-75ABUS2L
Serial communication unit
GT15-RS2-9P, GT15-RS4-9S, GT15-RS4-TE
RS-422 conversion unit
GT15-RS2T4-9P, GT15-RS2T4-25P
Ethernet communication unit
GT15-J71E71-100
MELSECNET/H communication unit
GT15-J71LP23-25, GT15-J71BR13
MELSECNET/10 communication unit
GT15-75J71LP23-Z*1, GT15-75J71BR13-Z*2
CC-Link IE Controller Network communication
unit
GT15-J71GP23-SX
CC-Link IE Field Network communication unit
GT15-J71GF13-T2
CC-Link communication unit
GT15-J61BT13, GT15-75J61BT13-Z*3
Interface converter unit
GT15-75IF900
Serial multi-drop connection unit
GT01-RS4-M
Connection Conversion Adapter
GT10-9PT5S
RS-232/485 signal conversion adapter
GT14-RS2T4-9P
*1
*2
*3
A9GT-QJ71LP23 + GT15-75IF900 set
A9GT-QJ71BR13 + GT15-75IF900 set
A8GT-J61BT13 + GT15-75IF900 set
 Option unit
Abbreviations and generic terms
Printer unit
Video/RGB unit
Description
GT15-PRN
Video input unit
GT16M-V4, GT15V-75V4
RGB input unit
GT16M-R2, GT15V-75R1
Video/RGB input unit
GT16M-V4R1, GT15V-75V4R1
RGB output unit
GT16M-ROUT, GT15V-75ROUT
Multimedia unit
GT16M-MMR
CF card unit
GT15-CFCD
CF card extension unit
*1
GT15-CFEX-C08SET
External I/O unit
GT15-DIO, GT15-DIOR
Sound output unit
GT15-SOUT
*1
A - 16
GT15-CFEX + GT15-CFEXIF + GT15-C08CF set.
 Option
Abbreviations and generic terms
Memory card
CF card
SD card
Description
GT05-MEM-16MC, GT05-MEM-32MC, GT05-MEM-64MC, GT05-MEM-128MC,
GT05-MEM-256MC, GT05-MEM-512MC, GT05-MEM-1GC, GT05-MEM-2GC,
GT05-MEM-4GC, GT05-MEM-8GC, GT05-MEM-16GC
L1MEM-2GBSD, L1MEM-4GBSD
Memory card adaptor
GT05-MEM-ADPC
Option function board
GT16-MESB, GT15-FNB, GT15-QFNB, GT15-QFNB16M,
GT15-QFNB32M, GT15-QFNB48M, GT11-50FNB, GT15-MESB48M
Battery
GT15-BAT, GT11-50BAT
For GT16
GT16-90PSCB, GT16-90PSGB, GT16-90PSCW, GT16-90PSGW,
GT16-80PSCB, GT16-80PSGB, GT16-80PSCW, GT16-80PSGW,
GT16-70PSCB, GT16-70PSGB, GT16-70PSCW, GT16-70PSGW,
GT16-60PSCB, GT16-60PSGB, GT16-60PSCW, GT16-60PSGW,
GT16-50PSCB, GT16-50PSGB, GT16-50PSCW, GT16-50PSGW,
GT16-90PSCB-012, GT16-80PSCB-012, GT16-70PSCB-012,
GT16-60PSCB-012, GT16-50PSCB-012, GT16H-60PSC
For GT15
GT15-90PSCB, GT15-90PSGB, GT15-90PSCW, GT15-90PSGW,
GT15-80PSCB, GT15-80PSGB, GT15-80PSCW, GT15-80PSGW,
GT15-70PSCB, GT15-70PSGB, GT15-70PSCW, GT15-70PSGW,
GT15-60PSCB, GT15-60PSGB, GT15-60PSCW, GT15-60PSGW,
GT15-50PSCB, GT15-50PSGB, GT15-50PSCW, GT15-50PSGW
For GT14
GT14-50PSCB, GT14-50PSGB, GT14-50PSCW, GT14-50PSGW
Protective Sheet
For GT12
GT11-70PSCB, GT11-65PSCB
For GT11
GT11-50PSCB, GT11-50PSGB, GT11-50PSCW, GT11-50PSGW,
GT11H-50PSC
For GT10
GT10-50PSCB, GT10-50PSGB, GT10-50PSCW, GT10-50PSGW,
GT10-40PSCB, GT10-40PSGB, GT10-40PSCW, GT10-40PSGW,
GT10-30PSCB, GT10-30PSGB, GT10-30PSCW, GT10-30PSGW,
GT10-20PSCB, GT10-20PSGB, GT10-20PSCW, GT10-20PSGW
Protective cover for oil
GT05-90PCO, GT05-80PCO, GT05-70PCO, GT05-60PCO, GT05-50PCO,
GT16-50PCO, GT10-40PCO, GT10-30PCO, GT10-20PCO
USB environmental protection cover
GT16-UCOV, GT16-50UCOV, GT15-UCOV, GT14-50UCOV, GT11-50UCOV
Stand
GT15-90STAND, GT15-80STAND, GT15-70STAND, A9GT-50STAND, GT05-50STAND
Attachment
GT15-70ATT-98, GT15-70ATT-87, GT15-60ATT-97, GT15-60ATT-96,
GT15-60ATT-87, GT15-60ATT-77, GT15-50ATT-95W, GT15-50ATT-85
Backlight
GT16-90XLTT, GT16-80SLTT, GT16-70SLTT, GT16-70VLTT, GT16-70VLTTA, GT16-70VLTN,
GT16-60SLTT, GT16-60VLTT, GT16-60VLTN, GT15-90XLTT, GT15-80SLTT, GT15-70SLTT,
GT15-70VLTT, GT15-70VLTN, GT15-60VLTT, GT15-60VLTN
Multi-color display board
GT15-XHNB, GT15-VHNB
Connector conversion box
GT11H-CNB-37S, GT16H-CNB-42S
Emergency stop sw guard cover
GT11H-50ESCOV, GT16H-60ESCOV
Memory loader
GT10-LDR
Memory board
GT10-50FMB
Panel-mounted USB port extension
GT14-C10EXUSB-4S, GT10-C10EXUSB-5S
A - 17
 Software
Abbreviations and generic terms
Description
GT Works3
Abbreviation of the SW DNC-GTWK3-E and SW DNC-GTWK3-EA
GT Designer3
Abbreviation of screen drawing software GT Designer3 for GOT1000 series
GT Simulator3
Abbreviation of screen simulator GT Simulator3 for GOT1000/GOT900 series
GT SoftGOT1000
Abbreviation of monitoring software GT SoftGOT1000
GT Converter2
Abbreviation of data conversion software GT Converter2 for GOT1000/GOT900 series
GT Designer2 Classic
Abbreviation of screen drawing software GT Designer2 Classic for GOT900 series
GT Designer2
Abbreviation of screen drawing software GT Designer2 for GOT1000/GOT900 series
iQ Works
Abbreviation of iQ Platform compatible engineering environment MELSOFT iQ Works
MELSOFT Navigator
Generic term for integrated development environment software included in the SW DNC-IQWK (iQ
Platform compatible engineering environment MELSOFT iQ Works)
GX Works2
Abbreviation of SW DNC-GXW2-E and SW DNC-GXW2-EA type programmable controller
engineering software
GX Simulator2
Abbreviation of GX Works2 with the simulation function
GX Simulator
Abbreviation of SW D5C-LLT-E(-EV) type ladder logic test tool function software packages
(SW5D5C-LLT (-EV) or later versions)
GX Developer
Abbreviation of SW D5C-GPPW-E(-EV)/SW D5F-GPPW-E type software package
GX LogViewer
Abbreviation of SW DNN-VIEWER-E type software package
PX Developer
Abbreviation of SW D5C-FBDQ-E type FBD software package for process control
MT Works2
Abbreviation of motion controller engineering environment MELSOFT MT Works2
(SW DNC-MTW2-E)
MT Developer
Abbreviation of SW RNC-GSV type integrated start-up support software for motion controller Q series
MR Configurator2
Abbreviation of SW DNC-MRC2-E type Servo Configuration Software
MR Configurator
Abbreviation of MRZJW -SETUP E type Servo Configuration Software
FR Configurator
Abbreviation of Inverter Setup Software (FR-SW -SETUP-WE)
NC Configurator
Abbreviation of CNC parameter setting support tool NC Configurator
FX Configurator-FP
Abbreviation of parameter setting, monitoring, and testing software packages for FX3U-20SSC-H
(SW D5C-FXSSC-E)
FX3U-ENET-L Configuration tool
Abbreviation of FX3U-ENET-L type Ethernet module setting software (SW1D5-FXENETL-E)
RT ToolBox2
Abbreviation of robot program creation software (3D-11C-WINE)
MX Component
Abbreviation of MX Component Version
MX Sheet
Abbreviation of MX Sheet Version
QnUDVCPU & LCPU Logging Configuration
Tool
Abbreviation of QnUDVCPU & LCPU Logging Configuration Tool (SW1DNN-LLUTL-E)
(SW D5C-ACT-E, SW D5C-ACT-EA)
(SW D5C-SHEET-E, SW D5C-SHEET-EA)
 License key (for GT SoftGOT1000)
Abbreviations and generic terms
License
A - 18
Description
GT15-SGTKEY-U, GT15-SGTKEY-P
 Others
Abbreviations and generic terms
Description
IAI
Abbreviation of IAI Corporation
AZBIL
Abbreviation of Azbil Corporation (former Yamatake Corporation)
OMRON
Abbreviation of OMRON Corporation
KEYENCE
Abbreviation of KEYENCE CORPORATION
KOYO EI
Abbreviation of KOYO ELECTRONICS INDUSTRIES CO., LTD.
SHARP
Abbreviation of Sharp Manufacturing Systems Corporation
JTEKT
Abbreviation of JTEKT Corporation
SHINKO
Abbreviation of Shinko Technos Co., Ltd.
CHINO
Abbreviation of CHINO CORPORATION
TOSHIBA
Abbreviation of TOSHIBA CORPORATION
TOSHIBA MACHINE
Abbreviation of TOSHIBA MACHINE CO., LTD.
HITACHI IES
Abbreviation of Hitachi Industrial Equipment Systems Co., Ltd.
HITACHI
Abbreviation of Hitachi, Ltd.
FUJI
Abbreviation of FUJI ELECTRIC CO., LTD.
PANASONIC
Abbreviation of Panasonic Corporation
PANASONIC INDUSTRIAL DEVICES SUNX
Abbreviation of Panasonic Industrial Devices SUNX Co., Ltd.
YASKAWA
Abbreviation of YASKAWA Electric Corporation
YOKOGAWA
Abbreviation of Yokogawa Electric Corporation
ALLEN-BRADLEY
Abbreviation of Allen-Bradley products manufactured by Rockwell Automation, Inc.
GE
Abbreviation of GE Intelligent Platforms
LS IS
Abbreviation of LS Industrial Systems Co., Ltd.
SCHNEIDER
Abbreviation of Schneider Electric SA
SICK
Abbreviation of SICK AG
SIEMENS
Abbreviation of Siemens AG
RKC
Abbreviation of RKC INSTRUMENT INC.
HIRATA
Abbreviation of Hirata Corporation
MURATEC
Abbreviation of Muratec products manufactured by Muratec Automation Co., Ltd.
PLC
Abbreviation of programmable controller
Control equipment
Generic term for control equipment manufactured by each corporation
Temperature controller
Generic term for temperature controller manufactured by each corporation
Indicating controller
Generic term for indicating controller manufactured by each corporation
CHINO controller
Abbreviation of indicating controller manufactured by CHINO CORPORATION
PC CPU module
Abbreviation of PC CPU Unit manufactured by CONTEC CO., LTD
GOT (server)
Abbreviation of GOTs that use the server function
GOT (client)
Abbreviation of GOTs that use the client function
Windows font
Abbreviation of TrueType font and OpenType font available for Windows
(Differs from the True Type fonts settable with GT Designer3)
Intelligent function module
Indicates the modules other than the PLC CPU, power supply module and I/O module that are mounted
to the base unit
MODBUS/RTU
Generic term for the protocol designed to use MODBUS protocol messages on a serial communication
MODBUS/TCP
Generic term for the protocol designed to use MODBUS protocol messages on a TCP/IP network
A - 19
HOW TO READ THIS MANUAL
 Symbols
Following symbols are used in this manual.
Refers to the information required.
Refers to information useful
for operation.
Indicates the location of related content.
Indicates the operation procedure.
Perform procedures in numerical order.
[
] : Indicates the setting items displayed
on the software and GOT screen.
: Refers to a button displayed on the
computer screen or the GOT screen,
or a key of the computer keyboard.
5 9 2 0
Since the above page was created for explanation purpose, it differs from the actual page.
A - 20
OVERVIEW
OVERVIEW
1
 About GOT
For the display screen, two kinds of screens are available: user screen
and utility screen.
PLC
2
SYSTEM
CONFIGURATION
A GOT is installed on the panel surface of a control panel or operating
panel and connects to the PLC within the control panel. The GOT carries
out switch operation, lamp display, data display, message display, etc.
Connector for
program
(1) User Screen
3
GOT
SPECIFICATIONS
The user screen is a screen drawn by drawing software.
The objects [Touch switch], [Lamp display], [Comment display], and
[Numeric display] can be arbitrarily arranged on the display.
Moreover, multiple screens created within drawing software can be
individually selected or overlapped for the display.
For details, refer to the following.
GT Designer3 Version1 Screen Design Manual
4
(2) Utility Screen
The utility screen is a factory drawn horizontal screen that cannot be edited.
Installing the BootOS or Standard monitor OS in the GOT from drawing software, the utility screen is displayed.
The utility screen has options for [Brightness/contrast], [Memory check], etc.
For details, refer to the following.
PARTS NAME
1.
5
UL, cUL
STANDARDS AND
EMC DIRECTIVE
9. to 18.
INSTALLATION
6
WIRING
7
OPTION
8
1. OVERVIEW
1-1
1.1 Features
Monitoring for turning ON/OFF bit devices of a PLC, forced turning ON/OFF the bit devices of a PLC, monitoring the
word device set value/current value and changing that numeric values are easily made.
(1) The display unit is used for engineers' stage replacement, setting change and troubleshooting or for
operation guidance to an operator.
•
•
•
•
Monitor
Forced turning ON/OFF
Set value change
Trouble check
(2) Improved monitoring performance and connectivity to FA devices
• Multiple languages are displayed using the Unicode2.1-compatible fonts and beautiful characters are drawn
using the TrueType and high quality fonts.
• Two types of display modes are provided: 65536-color display and monochrome display
A fine and beautiful full-color display which shows even small characters clearly, is enabled in the 65536-color
display by adopting the high intensity, wide viewing angle and high definition TFT color liquid crystal display.
(Also compatible with digital screen displays with 65536 colors, BMP, etc.)
In the monochrome display, 16 scales are used to improve the display.
• High speed monitoring through high speed communication at maximum of 115.2kbps.
• High speed display and high speed touch switch response.
• The operation performance is improved by the analog touch panel.
(3) More efficient GOT operations including screen design, startup, adjustment, management and
maintenance works
•
•
•
•
•
•
•
•
The 9MB built-in flash memory is included as standard.
SD card interface is included as standard.
RS-232 interface is included as standard.
RS-422/485 interface is included as standard.
USB interface (host/device) is included as standard.
Ethernet interface is included as standard.
System font types are increased by the adoption of the font installation system.
Four types of alarms (system alarm, user alarm, alarm history and alarm popup display) are integrated, and
realizing an efficient alarm notification.
(4) Enhanced support of FA device setup tools
• Transferring or monitoring the sequence programs using the PC connected to GOT is available, during
connection to A, QnA, L, Q, or FX series PLC CPU (FA Transparent function).
1-2
1. OVERVIEW
1.1 Features
1.1.1
1
Rough procedure
Install GT Designer3 in the PC.
OVERVIEW
The outline procedures before operating GOT and the descriptions of each item are shown below.
Refer to GT Designer3 Version1 Screen Design Manual
(Fundamentals).
2
Wire for the controller power supply and I/O.
SYSTEM
CONFIGURATION
Wire for the GOT power supply and the controller.
Refer to GT Designer3 Version1 Screen Design Manual
(Functions).
7. WIRING
Refer to GOT1000 Series Connection Manual for GT Works3.
Controller manuals
4
PARTS NAME
Turn on the power of GOT and controller.
16. INSTALLATION OF COREOS, BOOTOS AND
Install the OS to GOT.
STANDARD MONITOR OS
Refer to GT Designer3 Version1 Screen Design Manual
(Fundamentals).
UL, cUL
STANDARDS AND
EMC DIRECTIVE
5
Check that the OS is installed to GOT.
Refer to GT Designer3 Version1 Screen Design Manual
6
(Fundamentals).
INSTALLATION
Download project data.
3
SPECIFICATIONS
Create project data.
Turn on the controller power and check that the GOT
recognizes the controller.
7
WIRING
Check that the monitoring is normal.
OPTION
8
1. OVERVIEW
1.1 Features
1-3
1-4
1. OVERVIEW
1.1 Features
SYSTEM CONFIGURATION
1
OVERVIEW
2.
2.1 Overall Configuration
2
SYSTEM
CONFIGURATION
The overall configuration of GOT is as follows.
For the connection methods applicable to GOT1000 series and cable, refer to the following.
Bar code
reader
(Commercially
available)
3
Refer to
8.1.
Stand
Refer to
8.7.
RFID
controller
(Commercially
available)
USB
memory
Refer to
8.2.
Panel-mounted
Refer to
USB port
8.10.
extension
USB mouse
(Commercially
available)
Battery
Refer to
8.3.
Serial
multi-drop
connection
unit
Refer to
8.9.
USB
keyboard
(Commercially
available)
Protective
sheet
Refer to
8.4.
Connector
conversion
adapter
Refer to
8.8.
Personal
computer
(Commercially
available)
RS-232/485
Refer to
signal
conversion
8.11.
adapter
Printer *1
(Commercially
available)
4
PARTS NAME
SD card
5
Only hard copy of the screen can be printed.
UL, cUL
STANDARDS AND
EMC DIRECTIVE
*1
Refer to
Protective
cover for oil
8.5.
SPECIFICATIONS
GOT1000 Series Connection Manual for GT Works3
2.2 System Equipment
6
(1) Explanation of the GOT model name
Communication
interface
E : Built-in Ethernet
Power type
D : DC24V
Panel color type
B : Black
Display device type
L : monochrome (black and white)
T : TFT color (High intensity, wide angle view)
Resolution
Q : 320×240 (QVGA)
Display color type
0 : Monochrome (black and white) 16 scales
5 : 65535 colors
Screen size type
5 : 5.7"
GOT1000 series
GT14
2. SYSTEM CONFIGURATION
2.1 Overall Configuration
INSTALLATION
- Q T B D E
7
WIRING
5 5
8
OPTION
GT14
2-1
(2) Explanation of the option model name
GT
**
-
** ****
50 : Dedicated for 5.7"
16 : Dedicated for GT16
15 : Dedicated for GT15
14 : Dedicated for GT14
11 : Dedicated for GT11
10 : Dedicated for GT10
09 :
05 : Common for GT16/GT15/GT14/GT11/GT10
01 :
2.2.1
Product
name
GOT (GT14)
Model name
GT1455-QTBDE
5.7" [320 240 dots], TFT color liquid crystal display, 65536 colors,
24VDC, memory size 9MB, built-in battery, built-in Ethernet interface
GT1455-QTBD
5.7" [320 240 dots], TFT color liquid crystal display, 65536 colors,
24VDC, memory size 9MB, built-in battery
GT1450-QLBDE
5.7" [320 240 dots], STN monochrome liquid crystal display, monochrome (black/white),
24VDC, memory size 9MB, built-in battery, built-in Ethernet interface
GT1450-QLBD
5.7" [320 240 dots], STN monochrome liquid crystal display, monochrome (black/white),
24VDC, memory size 9MB, built-in battery
GOT
2-2
Specifications
2. SYSTEM CONFIGURATION
2.2 System Equipment
2.2.2
1
Option
Product name
1m
GT01-C30R4-8P
3m
2
10m
GT01-C300R4-8P
30m
GT01-C30R4-25P
3m
GT01-C100R4-25P
10m
For connecting GOT to QnA/A Motion controller CPU (A series), FXCPU (DSub 25pin)
GT01-C200R4-25P
20m
3
GT01-C300R4-25P
30m
For connecting GOT to FA-CNV CBL
For connecting GOT to serial communication unit (AJ71QC24(N)-R4)
GT09-C30R4-6C
3m
For connecting GOT to computer link module/serial communication unit
20m
Computer link connection GT09-C100R4-6C
cable
GT09-C200R4-6C
10m
20m
GT09-C300R4-6C
30m
QCPU direct connection
cable
GT01-C30R2-6P
3m
For connecting GOT to QCPU
FX expansion board
connection, FX special
adaptor connection, data
transfer cable
GT01-C30R2-9S
3m
For connecting GOT to FXCPU expansion board (D-Sub 9pin)
For connecting GOT to FXCPU special adaptor (D-Sub 9pin)
FX special adaptor
connection
GT01-C30R2-25P
3m
For connecting GOT to FXCPU special adaptor (D-Sub 25pin)
Computer link connection GT09-C30R2-9P
cable
GT09-C30R2-25P
3m
3m
4
PARTS NAME
QnA/A/FXCPU direct
connection cable,
computer link connection
cable
For connecting GOT to FXCPU (MINI DIN 8pin)
For connecting GOT to FXCPU expansion board (MINI DIN 8pin)
5
For connecting GOT to computer link module/serial communication unit
Connection cables for OMRON PLCs (Sold separately)
RS-422 cable
RS-232 cable
Cable
length
GT09-C30R40101-9P
3m
GT09-C100R40101-9P
10m
GT09-C200R40101-9P
20m
GT09-C300R40101-9P
30m
Contents
6
For connecting GOT to OMRON PLC, serial communication unit, serial communication
board
INSTALLATION
RS-422 cable
Model name
GT09-C30R40103-5T
3m
GT09-C100R40103-5T
10m
GT09-C200R40103-5T
20m
GT09-C300R40103-5T
30m
GT09-C30R40102-9P
3m
GT09-C100R40102-9P
10m
GT09-C200R40102-9P
20m
GT09-C300R40102-9P
30m
GT09-C30R20101-9P
3m
For connecting GOT to OMRON PLC, serial communication unit, communication board,
serial communication board
GT09-C30R20102-25S
3m
For connecting GOT to OMRON connection cable
GT09-C30R20103-25P
3m
For connecting GOT to OMRON rack type host link unit
For connecting GOT to serial communication board
7
For connecting GOT to OMRON rack type host link unit, communication board
8
OPTION
Product
name
SYSTEM
CONFIGURATION
FXCPU direct connection
cable, FX expansion
GT01-C100R4-8P
board connection cable
GT01-C200R4-8P
SPECIFICATIONS
GT01-C10R4-8P
Contents
UL, cUL
STANDARDS AND
EMC DIRECTIVE
RS-232
cable
Cable
length
WIRING
RS-422
cable
Model name
OVERVIEW
Connection cables for MITSUBISHI PLCs (Sold separately)
2. SYSTEM CONFIGURATION
2.2 System Equipment
2-3
Connection cables for KEYENCE PLCs (Sold separately)
Product
name
RS-422 cable
RS-232 cable
Model name
Cable
length
Contents
GT09-C30R41101-5T
3m
GT09-C100R41101-5T
10m
GT09-C200R41101-5T
20m
GT09-C300R41101-5T
30m
GT09-C30R21101-6P
3m
For connecting GOT to KEYENCE PLC
GT09-C30R21102-9S
3m
For connecting GOT to KEYENCE multi-communication unit
GT09-C30R21103-3T
3m
For connecting GOT to KEYENCE multi-communication unit
For connecting GOT to KEYENCE multi-communication unit
Connection cables for Panasonic PLCs (Sold separately)
Product
name
RS-232 cable
Model name
Cable
length
Contents
GT09-C30R20901-25P
3m
For connecting GOT to Panasonic RS422/232C conversion adapter
GT09-C30R20902-9P
3m
For connecting GOT to the tool port or RS232C port of Panasonic PLC, computer
communication unit
GT09-C30R20903-9P
3m
For connecting GOT to the RS232C port of Panasonic PLC
GT09-C30R20904-3C
3m
For connecting GOT to the RS232C port of Panasonic PLC
Connection cables for YASKAWA PLCs (Sold separately)
Product
name
RS-422 cable
RS-232 cable
2-4
Model name
Cable
length
GT09-C30R40201-9P
3m
GT09-C100R40201-9P
10m
GT09-C200R40201-9P
20m
GT09-C300R40201-9P
30m
GT09-C30R40202-14P
3m
GT09-C100R40202-14P
10m
GT09-C200R40202-14P
20m
GT09-C300R40202-14P
30m
GT09-C30R20201-9P
3m
GT09-C30R20202-15P
3m
GT09-C30R20203-9P
3m
GT09-C30R20204-14P
3m
GT09-C30R20205-25P
3m
2. SYSTEM CONFIGURATION
2.2 System Equipment
Contents
For connecting GOT to YASKAWA MEMOBUS module
For connecting GOT to YASKAWA PLC
For connecting GOT to YASKAWA PLC
For connecting GOT to YASKAWA MEMOBUS module
1
Connection cables for YOKOGAWA PLCs (Sold separately)
RS-232 cable
Cable
length
Contents
3m
GT09-C100R40301-6T
10m
GT09-C200R40301-6T
20m
GT09-C300R40301-6T
30m
GT09-C30R40302-6T
3m
GT09-C100R40302-6T
10m
GT09-C200R40302-6T
20m
GT09-C300R40302-6T
30m
GT09-C30R40303-6T
3m
GT09-C100R40303-6T
10m
GT09-C200R40303-6T
20m
GT09-C300R40303-6T
30m
GT09-C30R40304-6T
3m
GT09-C100R40304-6T
10m
GT09-C200R40304-6T
20m
GT09-C300R40304-6T
30m
GT09-C30R20301-9P
3m
For connecting GOT to YOKOGAWA CPU port/D-Sub 9pin conversion cable
GT09-C30R20302-9P
3m
For connecting GOT to YOKOGAWA PC link module
GT09-C30R20304-9S
3m
For connecting GOT to YOKOGAWA converter
OVERVIEW
GT09-C30R40301-6T
2
SYSTEM
CONFIGURATION
For connecting GOT to YOKOGAWA PC link module
3
SPECIFICATIONS
RS-422 cable
Model name
For connecting GOT to YOKOGAWA temperature controller
4
PARTS NAME
Product
name
Connection cables for Allen-Bradley PLCs (Sold separately)
RS-232 cable
Model name
Cable
length
5
Contents
GT09-C30R20701-9S
3m
For connecting GOT to Allen-Bradley PLC
GT09-C30R20702-25P
3m
For connecting GOT to Allen-Bradley Adapter
UL, cUL
STANDARDS AND
EMC DIRECTIVE
Product
name
Connection cables for SIEMENS PLCs (Sold separately)
Product
name
RS-232 cable
Model name
GT09-C30R20801-9S
Cable
length
3m
Contents
6
For connecting GOT to SIEMENS HMI Adapter
RS-232 cable
Model name
GT09-C30R21401-4T
Cable
length
3m
Contents
For connecting GOT to SHINKO indicating controller
7
SD card (Sold separately)
Product name
*1
Contents
L1MEM-2GBSD
SD memory card 2GB
L1MEM-4GBSD
SDHC memory card 4GB
-
Commercially-available SD card *1
Some models with the operations checked by our company are usable.
For the operation-checked models, refer to "Operation Check Results of Third Party SD Cards on GT14 Model" (Hime-T-P-0089)
separately available, or contact your local distributor.
8
OPTION
SD card
Model name
WIRING
Product
name
INSTALLATION
Connection cables for SHINKO indicating controller PLCs (Sold separately)
2. SYSTEM CONFIGURATION
2.2 System Equipment
2-5
USB memory (Sold separately)
Product name
Model name
USB memory
Commercially-available USB memory *2
*2
Contents
Some models with the operations checked by our company are usable.
For the operation-checked models, refer to "List of valid devices applicable for GOT1000 series" (T10-0039) separately available,
or contact your local distributor.
Battery (Sold separately)
Product name
Model name
Battery *3
GT11-50BAT
*3
Contents
Battery for clock data, alarm history, recipe data, time action setting value,
advanced alarm, advanced recipe, logging, hard copy, and SRAM user area
backups
At GOT purchase, it is installed in the main unit.
Stand (Sold separately)
Product name
Stand
Model name
GT05-50STAND
Contents
Stand for 5.7"
Protective cover for oil (Sold separately)
Product name
Protective cover for oil
Model name
GT05-50PCO
Contents
For 5.7" GOT
Protective sheet (Sold separately)
Product name
Model name
Contents
GT14-50PSCB
Protective sheet
Clear 5 sheets
GT14-50PSGB
GT14-50PSCW
5.7" protective sheet
GT14-50PSGW
Antiglare 5 sheets
Clear (Frame: white) 5 sheets
Antiglare (Frame: white) 5 sheets
Drawing software (Sold separately)
Product name
Model name
SW
GT Designer3
(
Contents
DNC-GTD3-E
Drawing software for GOT1000 series
indicates the version.)
PC connection cable (Sold separately)
Product name
Model name
Cable length
Contents
GT09-C30USB-5P
3m
GOT (USB Mini-B)
PC (USB)
GT01-C30R2-9S
3m
GOT (D-Sub 9pin)
PC (D-Sub 9pin)
Project data transfer cable
Panel-mounted USB port extension (Sold separately)
Product name
Panel-mounted USB port
extension
Model name
GT14-C10EXUSB-4S
Cable length
1m
Contents
Panel-mounted USB port extension, compatible with IP67f
Serial multi-drop connection unit (Sold separately)
Product name
Serial multi-drop connection
unit
Model name
GT01-RS4-M
Contents
For GOT multi-drop connection
Connector conversion adapter (Sold separately)
Product name
Connector conversion adapter
2-6
Model name
GT10-9PT5S
2. SYSTEM CONFIGURATION
2.2 System Equipment
Contents
For GOT multi-drop connection
1
Bar code reader, RFID controller (Sold separately)
Model name
Contents
Bar code reader
-
Commercially-available bar code reader *4
RFID controller
-
Commercially-available RFID controller *4
*4
Some models with the operations checked by our company are usable.
For the operation-checked models, refer to "List of valid devices applicable for GOT1000 series" (T10-0039) separately available,
or contact your local distributor.
SPECIFICATIONS
3
PARTS NAME
4
UL, cUL
STANDARDS AND
EMC DIRECTIVE
5
6
INSTALLATION
GT14-RS2T4-9P
Contents
For GOT multi-drop connection, multi-channel function connection,
temperature controller connection, and MODBUS(R)/RTU connection
7
WIRING
Model name
8
OPTION
Product name
RS-232/485 signal conversion
adapter
2
SYSTEM
CONFIGURATION
RS-232/485 signal conversion adapter (Sold separately)
OVERVIEW
Product name
2. SYSTEM CONFIGURATION
2.2 System Equipment
2-7
2-8
2. SYSTEM CONFIGURATION
2.2 System Equipment
SPECIFICATIONS
OVERVIEW
1
3.1 General Specifications
2
Storage ambient temperature
-20 to 60
0 to 55
(when horizontally installed), 0 to 50
Operating ambient humidity
10 to 90%, non-condensing (WBT: 39
Storage ambient humidity
10 to 90%, non-condensing
Under
Conforms to
intermittent
JIS B 3502 and
vibration
IEC 61131-2
Under
continuous
vibration
Vibration resistance
(when vertically installed)
)
3
Frequency
Acceleration
Halfamplitude
5 to 8.4Hz
-
3.5mm
8.4 to 150Hz
9.8m/s2
-
5 to 8.4Hz
-
1.75mm
8.4 to 150Hz
4.9m/s2
-
Sweep count
10 times each in
X, Y and Z
directions
SPECIFICATIONS
0 to 50
-
4
Shock resistance
Conforms to JIS B 3502, IEC 61131-2 (147 m/s2, 3 times each in X, Y and Z directions)
Operating atmosphere
Must be free of lamp black, corrosive gas, flammable gas, or excessive amount of electro
conductive dust particles and must be no direct sunlight. (Same as for saving)
Operating altitude *1
2000 m (6562 ft) max.
Installation location
Inside control panel
Overvoltage category *2
II or less
2 or less
Self-cooling
Grounding
Class D grounding (100
*1
*2
*3
or less), to be connected to the panel when grounding is not possible.
Do not use or store the GOT under pressures higher than the atmospheric pressure of altitude 0m (0ft.).
Failure to observe this instruction may cause a malfunction.
When the air inside the control panel is purged by pressurization, the surface sheet may be lifted by high pressure. As a result,
the touch panel may be difficult to press, and the sheet may be peeled off.
This indicates the section of the power supply to which the equipment is assumed to be connected between the public electrical
power distribution network and the machinery within the premises.
Category II applies to equipment for which electrical power is supplied from fixed facilities.
The surge voltage withstand level for up to the rated voltage of 300V is 2500V.
This index indicates the degree to which conductive pollution is generated in the environment where the equipment is used.
In pollution degree 2, only non-conductive pollution occurs but temporary conductivity may be produced due to condensation.
6
7
WIRING
Cooling method
5
8
OPTION
Pollution degree
*3
UL, cUL
STANDARDS AND
EMC DIRECTIVE
Display section
Operating ambient
Other than
temperature
display section
SYSTEM
CONFIGURATION
Specifications
PARTS NAME
Item
INSTALLATION
3.
3. SPECIFICATIONS
3.1 General Specifications
3-1
3.2 Performance Specifications
The performance specifications are as follows.
Specifications
Item
Display section *1
GT1455-QTBD(E)
Type
TFT color liquid crystal display
Screen size
5.7"
Resolution
320
Display size
W115(4.53)
Display character
16-dot standard font: 20 characters
12-dot standard font: 26 characters
Display color
Display angle
GT1450-QLBD(E)
Monochrome (black/white) liquid crystal display
240 dots
H86(3.39)[mm](inch) (Horizontal format)
15 lines (Horizontal format),
20 lines (Horizontal format)
65536 colors
*2
Monochrome (black/white) 16 scales
Left/Right: 80 degrees, Top: 80 degrees, Bottom: 60 Left/Right: 45 degrees, Top: 20 degrees, Bottom: 40
degrees (Horizontal format)
degrees (Horizontal format)
Intensity of liquid crystal
display only
400[cd/m2]
300[cd/m2]
Contrast adjustment
-
32-level adjustment
Intensity adjustment
8-level adjustment
Life
Approx. 50,000h. (Time for contrast to become 1/5 at operating ambient temperature of 25
)
LED type (irreplaceable)
Backlight
Backlight off/screen saving time can be set.*3
Touch panel*4
Life
Approx. 70,000h or longer. (Time for display intensity reaches 50% at operating ambient temperature of 25
Type
Analog resistive film
Key size
Minimum 2
)
2 dots (per key)
Number of points touched
Simultaneous presses not allowed. (Only 1 point can be touched.)
simultaneously
Life
C drive*5
Memory
D drive
1 million times (operating force 0.98N max.)
Built-in flash memory, 9Mbytes (for storing project data and OS)
Life (Number of write times): 100,000 times
SRAM (internal), 512Kbytes (battery backup)
GT11-50BAT lithium battery
Battery
Backup target
Clock data, alarm history, recipe data, time action setting value,
advanced alarm, advanced recipe, logging, hard copy and SRAM user area
Life
Approx. 5 years (Operating ambient temperature of 25
RS-422/485
RS-422/485, 1ch
Transmission speed: 115200/57600/38400/19200/9600/4800bps
Connector shape: D-Sub 9pin (Female)
Application: For communicating with a controller
Terminating resistor: Open/110 /330
)
(Switched by terminating resistor selector switch)*6 (At factory
shipment: 330 )
Built-in
interface
RS-232
RS-232, 1ch
Transmission speed: 115200/57600/38400/19200/9600/4800bps
Connector shape: D-Sub 9pin (Male)
Application: For communicating with a controller, connecting a bar code reader/RFID, connecting a PC
(project data upload/download, OS installation, FA transparent function)
Ethernet
(Only for models
equipped with Ethernet)
Data transfer method: 100BASE-TX, 10BASE-T, 1ch
Connector shape: RJ-45 (modular jack)
Application: For communicating with a controller, using the gateway function, connecting a PC (project
data upload/download, OS installation, FA transparent function)
USB
SD card
3-2
USB (Full Speed 12Mbps), Host, 1ch
Connector shape: TYPE-A
Application: For transferring data, storing data
USB (Full Speed 12Mbps), device, 1ch
Connector shape: Mini-B
Application: For connecting a PC (project data upload/download, OS installation, FA transparent function)
SD standard, 1ch
Supported memory card: SDHC memory card, SD memory card
Application: For uploading/downloading project data, OS installation, storing logging data
Buzzer output
Single tone (tone length adjustable)
Protective structure*7
IP67f (front section of the panel only)
External dimensions
W164(6.46)
Weight
Approx. 0.7kg (Excluding mounting fixtures)
Compatible software package
(GT Designer3 version)
Version1.37P or later
3. SPECIFICATIONS
3.2 Performance Specifications
H135(5.32)
D55(2.17)[mm](inch)
*4
*5
*6
*7
11.1 Display Setting
The touch panel is analog resistive film-type. If you touch the panel simultaneously in 2 points or more, the switch that is located
around the center of the touched point, if any, may operate. Do not touch the panel in 2 points or more simultaneously.
Do not press the GOT display section with a pointed material as a pen or driver. Doing so can result in a damage or failure of the
display section.
An analog resistive film-type touch panel does not require adjustment usually. However, misalignment between object position
and actual touched position may be caused as usage time passes. If misalignment between object position and actual touched
position may occur, adjust the touch panel position. Misalignment between object position and actual touched position may
operate an unintended object, which causes unintended operation by mis-output and mis-operation.
ROM in which new data can be written without deleting the written data
Set the terminating resistor selector switch of the GOT in accordance with the connection type when adopting GOT multidrop
connection.
Note that this does not guarantee all user's operation environment. The protection is not applied when the interface environment
protection cover is removed.
In addition, the product may not be used in environments under exposition of oil or chemicals for a long period of time, or in
environments filled with oil-mist.
3.3 Power Supply Specifications
Specifications
Item
GT1450-QLBD
GT1450-QLBDE
GT1455-QTBD
Fuse (built-in, irreplaceable)
1.6A
Power consumption
7.68W (320mA/24V)
8.40W (350mA/24V)
7.68W (320mA/24V)
8.40W (350mA/24V)
6.72W (280mA/24V)
7.44W (310mA/24V)
6.72W (280mA/24V)
7.44W (310mA/24V)
OVERVIEW
SYSTEM
CONFIGURATION
4
5
Inrush current
30A or less (26.4VDC) 2ms
Permissible instantaneous
power failure time
Within 5ms
INSTALLATION
24VDC (+10% -15%), ripple voltage 200mV or less
3
6
GT1455-QTBDE
Input power supply voltage
2
SPECIFICATIONS
*3
11.1 Display Setting
Gradation inversion is a characteristic of liquid crystal display panel. Please be forewarned that depending on the displayed color,
the visualization may be difficult even within the described view angle.
The GOT screen saving/backlight off function prevents images from becoming permanently etched on the display screen and
increases the backlight life.
1
PARTS NAME
*2
Bright dots (always lit) and dark dots (unlit) may appear on a liquid crystal display panel due to its characteristics. It is impossible
to completely avoid this symptom, as the liquid crystal display comprises of a great number of display elements. Flickers may be
observed depending on the display color.
Please note that these dots appear due to its characteristic and are not caused by product defect.
Flickers and partial discoloration may be generated on the liquid crystal display panel due to the display contents or the contrast
adjustment. However, please note that these phenomena appear due to its characteristic and are not caused by product defect.
There is a difference in the display brightness and the color tones between liquid crystal display panels. When using multiple
liquid crystal display panels, please note that there is an individual difference between them.
A crosstalk (shadow as an extension of the display) may appear on the liquid crystal display panel. Please note that it appears
due to its characteristic.
When the display section is seen from the outside of the display angle, the display color seems like it has changed. Please note
that it appears due to its characteristic. Especially, the response time of a STN liquid crystal display is slower in the lower
temperature due to its characteristic. Please use the display after checking the response time.
Please note that the response time, brightness and color of the liquid crystal display panel may vary depending on the usage
environmental temperature.
When the same screen is displayed for a long time, an incidental color or partial discoloration is generated on the screen due to
heat damage, and it may not disappear.
To prevent the heat damage, the screen saver function is effective.
For details on the screen saver function, refer to the following.
UL, cUL
STANDARDS AND
EMC DIRECTIVE
*1
Noise immunity
Noise voltage: 1000Vp-p, Noise width: 1μs (by noise simulator of 30 to 100Hz noise frequency)
7
Dielectric withstand voltage
500VAC for 1 minute (across power supply terminals and earth)
Insulation resistance
10M
Applicable wire size
0.75[mm2] or more for power supply, 2[mm2] or more for grounding
Applicable solderless terminal
Solderless terminal for M3 screw RAV1.25-3, V2-N3A, FV2-N3A
or larger by insulation resistance tester (across power supply terminals and earth)
WIRING
At backlight off
8
POINT
3. SPECIFICATIONS
3.3 Power Supply Specifications
OPTION
Operation at momentary power failure
The GOT continues to operate even upon 5ms or shorter instantaneous power failure.
The GOT stops operating if there is extended power failure or voltage drop, while it automatically resumes
operation as soon as the power is restored.
3-3
3-4
3. SPECIFICATIONS
3.3 Power Supply Specifications
PARTS NAME
1
OVERVIEW
4.
4.1 Front Panel
2
SYSTEM
CONFIGURATION
(4)
(1)(2)
3
SPECIFICATIONS
(5)(6)
(3)
No.
Name
PARTS NAME
4
Description
Display section
Displays the utility screen and the user creation screen.
(2)
Touch panel
For touch switch operation on the utility screen and the user creation screen
(3)
POWER LED
Lit in green: Power is correctly supplied.
Lit in orange: Screen saving.
Blinks in orange/green: Blown back light bulb
Not lit: Power is not supplied.
(4)
Logo label
Removable
(5)
USB interface
USB interface for communicating with PC (Device)
For OS installation, project data download, and FA transparent
(6)
USB environmental protection
cover
Opens/closes when the USB interface is used.
5
UL, cUL
STANDARDS AND
EMC DIRECTIVE
(1)
INSTALLATION
6
WIRING
7
OPTION
8
4. PARTS NAME
4.1 Front Panel
4-1
4.2 Back Panel
(1)
(4)
(5)
(7)
(8)
Battery cover opened
(6)
(14)
(2)
(9)
Power supply terminal layout
(13)
(12)
No.
4-2
(3)
(10)
(11)
(15)
Name
Description
(1)
RS-232 interface
For communicating with controller (PLC, microcomputer board, bar code reader, RFID, etc) or PC (OS
installation, project data download, transparent) (D-sub 9pin male)
(2)
RS-422/485 interface
For communicating with controller (PLC, microcomputer board, etc) (D-sub 9pin female)
(3)
USB interface
USB interface for data transfer, data storage (host)
(4)
Preventive hole from removing
for the USB cable
Hole fixed with banding band or others as a prevention from removing for the USB cable
(5)
Rating plate (nameplate)
The model name, current consumption, product number, H/W version, and BootOS version are described.
(6)
SD card interface
Interface for installing the SD card to the GOT
(7)
SD card access LED
Lit: SD card being accessed, Not lit: SD card is not accessed.
(8)
SD card access switch
Prohibits accessing the SD card removing the card from the GOT.
ON: SD card being accessed (SD card removal prohibited)
OFF: SD card not accessed (SD card removal possible)
(9)
Battery
GT11-50BAT battery for storing clock data, alarm history, recipe data, time action setting value, advanced
alarm, advanced recipe, logging, hard copy and SRAM user area
(10)
Battery cover
Opens/closes when the battery is replaced or the terminating resistor is selected.
(11)
Power terminal
Power terminal and FG terminal (for power supply (24VDC) to GOT and grounding)
(12)
Power terminal cover
Opens/closes when the power terminal is connected. (color: transparent)
(13)
Reset switch
Switch for resetting the hardware (Use an isolated rod to operate.)
(14)
Terminating resistor selector
switch
For switching the RS-422/485 communication interface terminating resistor
(15)
Ethernet communication status
LED
SD RD: Turns on in green during data communication,
100M: Turns on in green during 100Mbps transmission.
4. PARTS NAME
4.2 Back Panel
1
OVERVIEW
4.3 Rear Face
(2)
No.
Name
(1)
SYSTEM
CONFIGURATION
2
(2)
Description
Ethernet interface
For Ethernet connection to a controller (PLC microcomputer board) (RJ-45 connector)
(2)
Holes for unit mounting fixtures
Holes for the mounting fixtures (accessory) when the GOT is mounted to the panel (4 holes at top and
bottom)
3
SPECIFICATIONS
(1)
PARTS NAME
4
UL, cUL
STANDARDS AND
EMC DIRECTIVE
5
INSTALLATION
6
WIRING
7
OPTION
8
4. PARTS NAME
4.3 Rear Face
4-3
4-4
4. PARTS NAME
4.3 Rear Face
5.1 UL, cUL Standards
UL, cUL Standard are recognized in use by the following combination (Model and Hardware version of the GOT/LOT.).
Model
Hardware version of the GOT/LOT.
GOT
GT1455-QTBD
GT1455-QTBDE
GT1450-QLBD
GT1450-QLBDE
Version C or later
RS-232/485 signal conversion adapter
GT14-RS2T4-9P
LOT.121 or later
3
SPECIFICATIONS
POINT
Checking method of hard ware version.
Confirm the hardware version with the rating plate of the GOT.
4
GRAPHIC OPERATION TERMINAL
MODEL GT1455-QTBDE
IN 20. 4 26. 4VDC POWER 8.40W MAX
G
MAC. ADD. 0026926212C6
MITSUBISHI ELECTRIC COPORATION
MADE IN JAPAN
JY550D26101C
CQ
PARTS NAME
S/N 1217999 CQ
2
SYSTEM
CONFIGURATION
Item
1
OVERVIEW
UL, cUL STANDARDS AND EMC DIRECTIVE
Hardware
version
5
UL, cUL
STANDARDS AND
EMC DIRECTIVE
 General notes on Power supply
This equipment must be supplied by a UL Listed or Recognized 24V DC rated power supply and UL Listed or
Recognized fuse rated not higher than 4A, or a UL Listed Class 2 power supply.
 Using GOT
GOT is for use on a Flat Surface of a Type 1 Enclosure.
6
5.2 EMC Directive
For the products sold in European countries, the conformance to the EMC Directive, which is one of the European
Directives, has been a legal obligation since 1996. Also, conformance to the Low Voltage.
Directive, another European Directives, has been a legal obligation since 1997.
Manufacturers who recognize their products must conform to the EMC and Low Voltage Directive are required to declare
that their products conform to these Directives and put a "CE mark" on their products.
7
WIRING
• This product is designed for use in industrial applications.
• Manufactured by: Mitsubishi Electric Corporation
2-7-3 Marunouchi, Chiyoda-ku, Tokyo 100-8310 Japan
• Manufactured at: Mitsubishi Electric Corporation Himeji Works
840 Chiyoda-machi, Himeji, Hyogo 670-8677 Japan
• Manufactured at: Mitsubishi Electric Corporation Nagoya Works
1-14 Yada-minami 5-Chome, Higashi-ku, Nagoya 461-0048 Japan
• Authorized Representative in the European Community: Mitsubishi Electric Europe B.V.
Gothaer Str. 8, 40880 Ratingen, Germany.
INSTALLATION
5.
OPTION
8
5. UL, cUL STANDARDS AND EMC DIRECTIVE
5.1 UL, cUL Standards
5-1
5.2.1
Requirements to Meet EMC Directive
EMC Directives are those which require "any strong electromagnetic force is not output to the external.:Emission
(electromagnetic interference)" and "It is not influenced by the electromagnetic wave from the external.: Immunity
(electromagnetic sensitivity)".
Items  EMC directive thru  Grounding summarize the precautions to use GOT and configure the mechanical unit in
order to match the EMC directives.
Though the data described herein are produced with our best on the basis of the requirement items and standards of the
restrictions gathered by Mitsubishi, they do not completely guaranteed that all mechanical unit manufactured according
to the data do not always match the above directives. The manufacturer itself which manufactures the mechanical unit
must finally judge the method and others to match the EMC directives.
 EMC directive
The standards of the EMC Directive are shown below.
Applied standard
Test standard
Test details
Standard value
30M-230MHz QP:
EN55011
*1
Radiated noise
Electromagnetic emissions from the
product are measured.
30dB V/m (30m in measurement range)*2, *3
230M-1000MHz QP:
37dB V/m(30m in measurement range)*2, *3
EN61000-4-2
Electrostatic
immunity*1
EN61000-4-3
Radiated field AM
modulation*1
EN61131-2
: 2007
Immunity test in which field is irradiated
to the product.
Immunity test in which burst noise is
applied to the power line and signal
Fast transient burst noise*1
lines.
EN61000-4-4
EN61000-4-5
Surge immunity*1
EN61000-4-6
Conducted RF immunity*1
EN61000-4-8
Power supply frequency
magnetic field immunity
*1
*2
*3
5-2
Immunity test in which static electricity is
applied to the cabinet of the equipment.
Immunity test in which lightening surge
is applied to the product.
4kV Contact discharge
8kV Aerial discharge
80-1000MHz:10V/m
1.4-2GHz:3V/m
2.0-2.7GHz:1V/m
80%AM modulation@1kHz
Power line:2kV
Digital I/O(24V or higher): 1kV
(Digital I/O(24V or less))> 250V
(Analog I/O, signal lines)> 250V
Power line (between line and ground):
Power line (between lines):
Data communication port:
0.5kV
0.5kV
1kV
Immunity test in which a noise inducted
on the power and signal lines is applied.
Power line: 10V
Data communication port: 10V
Test for checking normal operations
under the circumstance exposed to the
ferromagnetic field noise of the power
supply frequency (50/60Hz).
30 A/m
The GOT is an open type device (device installed to another device) and must be installed in a conductive control panel.
The above test items are conducted in the condition where the GOT is installed on the conductive control panel and combined
with the Mitsubishi PLC.
QP: Quasi-peak value, Mean : Average value
The above test items are conducted in the following conditions.
30M-230MHz QP : 40dB V/m (10m in measurement range)
230M-1000MHz QP : 47dB V/m (10m in measurement range)
5. UL, cUL STANDARDS AND EMC DIRECTIVE
5.2 EMC Directive
Ground and power supply wires for the GOT must be connected as described below.
Provide a grounding point near the GOT. Short-circuit the FG terminals of the GOT (FG: frame ground) and
ground them with the thickest and shortest wire possible (The wire length must be 30cm (11.81in.) or shorter.)
The FG terminals function is to pass the noise generated in the PC system to the ground, so an impedance that
is as low as possible must be ensured. As the wires are used to relieve the noise, the wire itself carries a large
noise content and thus short wiring means that the wire is prevented from acting as an antenna.
Note) A long conductor will become a more efficient antenna at high frequency.
(3) Shock protection
In order to prevent those who are unfamiliar with power facility, e.g., an operator, from getting a shock, make
sure to take the following measures on the control panel.
(a) Store the GOT within the control panel locked, and allow only those who are familiar with power facility to
unlock the panel.
(b) Build the structure in order that the power supply will be shut off when the control panel is opened.
(4) Dustproof and waterproof features
The control panel also provides protection from dust, water and other substances. Insufficient ingression
protection may lower the insulation withstand voltage, resulting in insulation destruction. The insulation in the
GOT is designed to cope with the pollution level 2, so use in an environment with pollustion level 2 or better.
Pollution level1 :
Pollution level2 :
An environment where the air is dry and conductive dust does not exist.
An environment where conductive dust does not usually exist, but occasional
temporary conductivity occurs due to the accumulated dust.
Generally, this is the level for inside the control panel equivalent a control room or
on the floor of a typical factory.
An environment where conductive dust exits and conductivity may be generated
due to the accumulated dust.
An environment for a typical factory floor.
Continuous conductivity may occur due to rain, snow, etc. An outdoor environment.
Pollution level3 :
Pollution level4 :
The following are applicable ground terminals. Use them in the grounded state.
Be sure to ground the GOT for ensuring the safety and complying with the EMC Directive.
:
Functional grounding
:
Improves the noise resistance.
SYSTEM
CONFIGURATION
5
6
7
8
OPTION
Protective grounding
Ensures the safety of the GOT and improves the noise resistance.
4
WIRING
 Grounding
3
SPECIFICATIONS
(2) Connection of power and ground wires
2
PARTS NAME
(a) The control panel must be conductive.
(b) When fixing a top or bottom plate of the control panel with bolts, do not coat the plate and bolt surfaces so
that they will come into contact.
And connect the door and box using a thick grounding cable in order to ensure the low impedance under
high frequency.
(c) When using an inner plate to ensure electric conductivity with the control panel, do not coat the fixing bolt
area of the inner plate and control panel to ensure conductivity in the largest area as possible.
(d) Ground the control panel using a thick grounding cable in order to ensure the low impedance under high
frequency.
(e) Holes made in the control cabinet must be 10 cm (3.94inch) diameter or less. If the holes are 10cm
(3.94inch) or larger, radio frequency noise may be emitted.
In addition, because radio waves leak through a clearance between the control panel door and the main
unit, reduce the clearance as much as practicable.
The leakage of radio waves can be suppressed by the direct application of an EMI gasket on the paint
surface.
UL, cUL
STANDARDS AND
EMC DIRECTIVE
(1) Control panel
INSTALLATION
GOT is an open type device (device installed to another device) and must be installed in a conductive control panel.
It not only assure the safety but also has a large effect to shut down the noise generated from GOT, on the control
panel.
OVERVIEW
1
 Control panel
5. UL, cUL STANDARDS AND EMC DIRECTIVE
5.2 EMC Directive
5-3
5.2.2
EMC Directive-Compliant System Configuration
For information of the EMC Directive-compliant models please consult with your nearest Mitsubishi product provider.
 GOT
Use any of the following GOTs with which CE mark logo is printed on the rating plate.
When using a GOT other than shown below, the system does not conform to the EMC Directive.
Item
Model
Hardware version of the GOT
GT1455-Q
GT1455-QTBD
GT1455-QTBDE
Version C or later
GT1450-Q
GT1450-QLBD
GT1450-QLBDE
Version C or later
POINT
Checking method of hard ware version.
Confirm the hardware version with the rating plate of the GOT.
GRAPHIC OPERATION TERMINAL
MODEL GT1455-QTBDE
IN 20. 4 26. 4VDC POWER 8.40W MAX
S/N 11Y0086
BQ G
BQ
MAC. ADD. 002692621123
MITSUBISHI ELECTRIC COPORATION
MADE IN JAPAN
JY550D26001C
Hardware
version
 Connection method
Use the following methods to connect with the GOT to ensure compliance with the EMC Directive.
: Compliant with EMC Directive
Connection method*1
: Not compliant with EMC Directive
GT14
Direct connection to CPU
Computer link connection
CC-Link connection (via G4)
Ethernet connection
GOT multi-drop connection
*1
Other connections
*1
When connecting the GOT to other controllers as a PLC manufactured by other company, create the cable (by the user) and
configure the system to meet the EMC Directive specifications for the connected device.
POINT
Connected devices
If connecting to the PLC or microcomputer other than Mitsubishi products
(MELSEC-Q series, MELSEC-L series, MELSEC-QnA , MELSEC-A series or MELSEC-FX series) please
refer to the EMC Directive compliance manual for that specific device.
5-4
5. UL, cUL STANDARDS AND EMC DIRECTIVE
5.2 EMC Directive
Any device which utilizes a data communication function is susceptible to the wider effects of local EMC noise.
Therefore, when installing any communication cables care should always be taken with the routing and location of
those cables. The GOT identified on the previous page are compliant with the EMC requirement when the following
communication cables are used.
(1) Panel-mounted USB port extension
2
GT14-C10EXUSB-4S
User Made Cables
The cable need to be independently tested by the user to demonstrate EMC
compatibility when they are used with the GOT, the PLC of MELSEC-Q series,
MELSEC-L series, MELSEC-QnA, MELSEC-A series and MELSEC-FX series.
(3) Ethernet connection cable
Shielded twisted pair cable (STP)
(4) PLC (manufactured by other company), microcomputer, temperature controller, inverter, servo amplifier,
CNC, MODBUS(R)/RTU or MODBUS(R)/TCP connection
Produce the cable (RS-232 cable, RS-422 / 485 cable) for connecting the GOT to a controller with reference to
the following manual.
Precautions for Wiring/Connecting the EMC Directive-Compliant Product
Wire and connect GOT1000 series equipments as instructed below. If the GOT1000 series equipments are configured in
a way different from the following instructions, the system may not comply with EMC directives.
 Power and ground wires wiring method
(1) Power and ground wires wiring method
Connect the power wire and connection cable as shown in the illustration, and be sure to attach a ferrite core
(TDK Corporation type ZCAT3035-1330 or similar) within the range shown below.
Lead the power wire and ground wire as shown in 5.2.1  Control panel (2).
Be sure to ground the FG cable, and protective ground cable.
5
UL, cUL
STANDARDS AND
EMC DIRECTIVE
5.2.3
4
PARTS NAME
GOT1000 Series Connection Manual for GT Works3 and a controller used
SPECIFICATIONS
3
6
INSTALLATION
Existing Cables
SYSTEM
CONFIGURATION
(2) Direct connection cable
GT01-C30R2-6P, GT01-C30R4-25P,
GT01-C100R4-25P, GT01-C200R4-25P,
GT01-C300R4-25P, GT01-C10R4-8P,
GT01-C30R4-8P, GT01-C100R4-8P,
GT01-C200R4-8P, GT01-C300R4-8P,
GT01-C30R2-9S, GT01-C30R2-25P,
WS0-C20R2
OVERVIEW
1
 About the cable used
7
TDK
WIRING
Up to 75mm
OPTION
8
5. UL, cUL STANDARDS AND EMC DIRECTIVE
5.2 EMC Directive
5-5
POINT
Any device which utilizes a data communication function is susceptible to the wider effects of local EMC noise.
Therefore, when installing any communication cables care should always be taken with the routing and location of
those cables.
Optional ferrite cores are recommended when the cable route is close to EMC noise sources like welders, large
motors, etc.
All tests have been performed with original Mitsubishi cables. For customer prepared cables, please refer to the
previous page.
GOT Unit
GT1450-QLBD
GT1450-QLBDE
GT1455-QTBD
GT1455-QTBDE
Existing Cables
User Made Cables
3rd party cables need to be independently
tested by the user to demonstrate EMC
compliance.
Ex. GT01-C30R4-8P (as shown in EX.1)
Example 1
F = Ferrite core
Ex. NEC TOKIN - ESD-R-17S or similar
GT01-C30R4-8P
(250mm)
(9.84inch)
Programmable
controller
100mm
(3.93inch)
F
140mm
(5.51inch)
F
Comes equipped
Optional
5-6
F
5. UL, cUL STANDARDS AND EMC DIRECTIVE
5.2 EMC Directive
Optional
GOT units
INSTALLATION
MOUNTING PRECAUTIONS
OVERVIEW
CAUTION
• Use the GOT in the environment that satisfies the general specifications described in this manual.
Not doing so can cause an electric shock, fire, malfunction or product damage or deterioration.
• Never drop cutting chips and electric wire chips into the ventilation window of the GOT when you drill screw holes
or perform wiring.
Otherwise, fire, failure or malfunction may be caused.
• Connect connection cables securely to the specified connectors while the power is turned OFF.
Imperfect connection may cause malfunction or failure.
• Operate and store the GOT in environments without direct sunlight, dust, lamp black, conductive dust, corrosive
gas, combustible gas, high temperature, condensation, wind, rain, vibrations and impacts.
Electric shock, fire, malfunction, product damage or deterioration can be caused.
• Tighten the mounting screws within the specified torque range.
Undertightening can cause the GOT to drop, short circuit or malfunction. Also, undertightening can disable
waterproof or oil proof effect.
Overtightening can cause a drop, short circuit or malfunction due to the damage of the screws or the GOT. Also,
"distortion" of the GOT or the panel may disable waterproof or oil proof effect.
6.1 Control Panel Inside Dimensions for Mounting GOT
Mount the GOT onto the control panel while considering the following control panel inside dimensions.
Vertical installation of the GOT requires a space with the same dimensions as the horizontal installation turned 90
degrees clockwise (seen from the display side).
2
SYSTEM
CONFIGURATION
• Be sure to shut off all phases of the external power supply used by the system before mounting or removing the
GOT to/from the panel.
Not doing so can cause the unit to fail or malfunction.
3
SPECIFICATIONS
WARNING
4
PARTS NAME
MOUNTING PRECAUTIONS
1
5
UL, cUL
STANDARDS AND
EMC DIRECTIVE
6.
6
POINT
152 (5.99")
140 (5.52")
WIRING
7
8
OPTION
120 (4.73")
30 (1.19")
INSTALLATION
Applicable cable
Some cables may need to be longer than the specified dimensions when connecting to the GOT. Therefore,
consider the connector dimensions and bending radius of the cable as well for installation.
Unit: mm (inch)
6. INSTALLATION
6.1 Control Panel Inside Dimensions for Mounting GOT
6-1
6.2 Panel Cutting Dimension
Make holes in the panel according to the dimensions list below.
Also, ensure 10mm of space in upper and lower parts of the panel for mounting fixtures.
• Horizontal format (If the vertical format is selected, the dimension must be rotated 90 degrees.)
+2
+0.08"
153 -0 (6.03" -0
)
+0.08"
121 +2
)
-0 (4.77" -0
10 (0.4")
or more
Within 2 (0.08”) to 4 (0.16”)
10 (0.4")
or more
Unit: mm (inch)
6.3 Mounting Position
When mounting the GOT, the following clearances must be maintained from other structures and devices.
• The below diagram represents a horizontal installation. (The same clearances must be maintained when rotating the
GOT 90 degrees clockwise for a vertical installation.)
Installation Environment
A, D
In the presence of radiated-noise or heat-generating equipment nearby
50mm or more
In the absence of radiated-noise or heat-generating equipment nearby
20mm or more
80mm or
C
more*1
20mm or more
50mm or
E
more*2
20mm or more
Vertical Format....50 mm (1.97") or more
Vertical Format....80 mm (3.14") or more
B
*1
*2
B
D
E
A
C
Panel thickness: 2 to 4mm
(0.08 to 0.16inch)
6-2
6. INSTALLATION
6.2 Panel Cutting Dimension
100mm or more
20mm or more
When mounting the main unit to a control panel or similar fixture, set the GOT display section as shown below.
 Horizontal installation
When the temperature inside the control panel is 40 to 55
105 degrees.
, the mounting angle should be in the range from 60 to
105°
GOT
display
section
60°
3
SPECIFICATIONS
Control panel,
etc.
The GOT will have a longer lifetime if used within the mounting angles shown above.
Ideally, the temperature inside the control panel should not exceed 0 to 40 .
 Vertical installation
, the mounting angle should be in the range from 60 to
GOT
back panel
105°
5
60°
UL, cUL
STANDARDS AND
EMC DIRECTIVE
GOT
display
section
4
PARTS NAME
When the temperature inside the control panel is 40 to 50
105 degrees.
2
SYSTEM
CONFIGURATION
GOT
back panel
OVERVIEW
1
6.4 Control Panel Temperature and Mounting Angle
Control panel,
etc.
The GOT will have a longer lifetime if used within the mounting angles shown above.
Ideally, the temperature inside the control panel should not exceed 0 to 40 .
INSTALLATION
6
WIRING
7
OPTION
8
6. INSTALLATION
6.4 Control Panel Temperature and Mounting Angle
6-3
6.5 Installation Procedure
The GOT is designed to be embedded into a panel. Mount the GOT by following the procedure below.
For the panel cutting dimension, refer to "6.2 Panel Cutting Dimension".
Also, be sure that the thickness of the mounting panel face is 2 to 4mm.
1.
Packing
Magnified
illustration
Installing the packing
Install packing to the packing installation groove on the back
panel of the GOT.
While referring to the cross sectional view of the packing shown
left, push the thinner side into the packing groove.
(Left drawing is the example of lateral format.)
Packing
Packing installation groove
Packing cross sectional view
Inserting direction
2.
Inserting into the panel face
Insert the GOT from the front side of the panel.
Mounting hole
Enlarged view
3.
Fixing the GOT
Engage the hook of the mounting fixture (accessory) to the unit
fixing hole of the GOT and fix them by tightening the mounting
screws in the torque range of 0.3 to 0.5N·m.
Mounting
bracket
Mounting
screw
4.
6-4
6. INSTALLATION
6.5 Installation Procedure
A protection film is attached on the display section of GOT prior
to shipment.
Remove the film when the installation is completed.
1
(1) Tightening the mounting screw
Tighten the mounting screws within the specified torque range.
Undertightening can cause a drop and disable waterproof or oil proof effect.
Overtightening may damage the unit, or distort the panel and make a surface waviness on the display area,
leading to deterioration of the visibility or incorrect input from the touch panel. Also, overtightening can disable
waterproof or oil proof effect.
• Specified torque range: 0.3 to 0.5N·m
2
SYSTEM
CONFIGURATION
Cautions on installation
OVERVIEW
POINT
4
PARTS NAME
(2) Mounting panel face
Make sure that the panel surface is free from warpage, flaws and irregularities. Warpage, flaws and
irregularities may disable the waterproof effect.
Select proper panel thickness under consideration of the panel strength.
(For example, the panel strength may be insufficient depending on the panel material and dimensions even if
the panel thickness is acceptable. Insufficient panel strength may cause warpage depending on the
installation positions of the GOT and other equipment.)
SPECIFICATIONS
3
UL, cUL
STANDARDS AND
EMC DIRECTIVE
5
INSTALLATION
6
WIRING
7
OPTION
8
6. INSTALLATION
6.5 Installation Procedure
6-5
6-6
6. INSTALLATION
6.5 Installation Procedure
WIRING
OVERVIEW
1
WARNING
• Be sure to shut off all phases of the external power supply used by the system before wiring.
Failure to do so may result in an electric shock, product damage or malfunctions.
2
• Please make sure to ground FG terminal of the GOT power supply section by applying 100 or less which is used
exclusively for the GOT.
Not doing so may cause an electric shock or malfunction.
• Correctly wire the GOT power supply section after confirming the rated voltage and terminal arrangement of the
product.
Not doing so can cause a fire or failure.
• Exercise care to avoid foreign matter such as chips and wire offcuts entering the GOT.
Not doing so can cause a fire, failure or malfunction.
4
CAUTION
WIRING PRECAUTIONS
3
SPECIFICATIONS
• Tighten the terminal screws of the GOT power supply section in the specified torque range.
Undertightening can cause a short circuit or malfunction.
Overtightening can cause a short circuit or malfunction due to the damage of the screws or the GOT.
SYSTEM
CONFIGURATION
WIRING PRECAUTIONS
PARTS NAME
• Plug the communication cable into the connector of the connected unit and tighten the mounting and terminal
screws in the specified torque range.
Undertightening can cause a short circuit or malfunction.
Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit.
This chapter describes the wiring to the GOT power supply section.
For the connection with a PLC, refer to the following.
5
UL, cUL
STANDARDS AND
EMC DIRECTIVE
GOT1000 Series Connection Manual for GT Works3
For the dimensional drawing of connection cables, refer to the following.
Appendix.1 External Dimensions
6
HINT
There are two kinds of noises: Radiated noise that is transmitted into the air and Conductive noise that is directly
transmitted along connected lines.
Countermeasures must be taken considering both kinds of noises and referring to the following 3 points.
(1) Protecting against noise
INSTALLATION
General preventive measures against noise
7
(a) Keep signal lines away from noise sources such as a power cable or a highpower drive circuit.
(b) Shield the signal lines.
(2) Reducing generated noise
(a) Use a noise filter, etc. to reduce the level of the noise generated due to a source such as a high-power
motor drive circuit.
(b) Attach surge killers to the terminals on the No Fuse Breaker (NFB), electromagnetic contactors, relays,
solenoid valves, and generators to suppress noise interference.
(3) Releasing noise to the ground
WIRING
7.
8
(a) Make sure to connect the ground cable to the ground.
(b) Use a short and thick cable to lower its impedance.
Ground the power system and the control system separately.
OPTION
(c)
7. WIRING
7-1
7.1 Power Supply Wiring
7.1.1
Wiring example
Connect the power supply to the power terminals on the back panel of the GOT.
Use 0.75mm2 or thicker cables to avoid voltage drop and tighten the terminal screw with the specified torque securely.
PC and external
device connection
cables
+
Grounding
(100 or less)
7.1.2
-
24VDC
power supply
Grounding the GOT
 About grounding
Make sure to carry out the following for grounding.
• Carry out the independent grounding if possible.
Apply the class D grounding. (Keep the grounding resistance within 100 or less.)
• If the independent grounding is impossible, carry out the shared grounding as shown in fig.2) below.
GOT
Other
device
Grounding
(100 or less)
(1) Independent ground
...... Best condition
GOT
Other
device
GOT
Other
device
Grounding
(100 or less)
(2) Shared grounding
...... Good condition
(3) Common grounding
...... Not allowed
• Use the cable of 2mm2 or more for grounding.
Set the grounding point closer to the GOT to make the grounding cable short as possible.
7-2
7. WIRING
7.1 Power Supply Wiring
Terminal screws should be tightened to between 0.5 to 0.8N·m. Terminal screws must be secured to prevent a loose
connection thus avoiding a malfunction.
Do not tighten the terminal screw with a torque exceeding the specified torque. Failure to do so may cause
equipment failures or malfunctions.
3.2
Terminal
screw
6.2mm
or less
Solderless
terminal
Terminal
screw
Solderless
terminal
2
SYSTEM
CONFIGURATION
3.2
6.2mm
or less
7.1.3
When wiring two cables to
one terminal
Cable size
For power supply: 0.75mm2 or more For grounding: 2mm2 or more
Solderless terminal
M3 solderless terminal (applicable solderless terminal: RAV1.25-3, V2-N3A, FV2-N3A)
Tightening torque
0.5 to 0.8N·m
3
SPECIFICATIONS
When wiring one cable to
one terminal
The cause of malfunctions related wiring/Remedy
4
Grounding of the GOT may cause electric potential difference and noise interference, which may result in GOT
malfunctions. These problems may be resolved by taking the following measures.
PARTS NAME
 Wiring path of the GOT's ground cable and power line
Bundling the GOT's ground cable and power line together can cause interference noise, which may result in
malfunctions.
Keeping the GOT's ground cable and power line away from each other will help minimize noise interference.
5
UL, cUL
STANDARDS AND
EMC DIRECTIVE
FG
OVERVIEW
1
 Recommended terminal shape
FG
6
Bad : Bundling the ground cable and
the power cable
WIRING
7
8
OPTION
Good : Wiring the ground cable away from the
power cable
Power supply for power equipment
INSTALLATION
Power supply for power equipment
7. WIRING
7.1 Power Supply Wiring
7-3
 Connecting the ground cable from the panel that houses control equipment to the panel to
which the GOT is grounded
When running a single ground cable from the panel that houses such piece of control equipment as a PLC to the
panel to which the GOT is grounded, the ground cable may have to be directly connected to the terminal on the GOT.
Connection cable
FG
Ground cable from
the panel that
houses control
equipment
If electric potential difference between the ground points created by it causes malfunctions, lowering the voltage as
shown in Remedy 1 below may solve the problem.
• Remedy 1 (Refer to the figures Remedy 1-1 and 1-2 below.)
If the electric potential difference between the ground cable and the panel that houses the GOT is creating
problems, connect the ground cable to the panel also.
If the wiring method as shown in Remedy 1-1 is not feasible, follow Remedy 1-2.
Connection cable
Connection cable
Ground cable from
the panel that
houses control
equipment
FG
Ground cable from
the panel that
houses control
equipment
FG
Use the thickest
cable possible.
Use the thickest
cable possible.
Panel
grounding
Panel
grounding
Remedy 1-2
Remedy 1-1
If taking Remedy 1 worsens noise interference, taking Remedy 2 may alleviate it.
• Remedy 2 (Refer to the figures Remedy 2-1 and 2-2 below.)
Attach a ferrite core to the cable if noise from the GOT panel has adverse effects on the GOT when Remedy 1
is taken.
Wind the wire around the ferrite core several times (approx. 3 times), if a ferrite core is used.
If the wiring method as shown in Remedy 2-1 is not feasible, follow Remedy 2-2.
Connection cable
Connection cable
Ground cable from
the panel that
houses control
equipment
FG
Ferrite core
Use the thickest
cable possible.
Use the thickest
cable possible.
FG
Ferrite core
Panel
grounding
Remedy 2-1
7-4
Ground cable from
the panel that
houses control
equipment
7. WIRING
7.1 Power Supply Wiring
Panel
grounding
Remedy 2-2
1
7.2 Wiring inside and outside the panel
OVERVIEW
Wiring inside
Run power lines, servo amplifier drive wires, and communication cables so that they do not cross each other.
Noise interference that is generated by cables that cross each other may cause malfunctions.
Surge suppressors are an effective way to filter out surge noise that is generated from no fuse breakers (NFB),
electromagnetic contactors (MC), relays (RA), solenoid valves, and induction motors.
For surge killers, refer to the section to follow.
7.2.3 Attaching surge killers to control equipment
Crossing power lines and communication cables
Uncrossed power lines and
communication cables
NFB
PLC
PLC I/O wire
MC
MC
RA
PLC I/O wire
MC
RA
MC
RA
RA
4
Drive control wire
Drive control wire
Terminal block
Terminal block
7.2.2
3
GOT connection cable
SPECIFICATIONS
GOT connection cable
PLC
NFB
Power
cable
PARTS NAME
Power
cable
SYSTEM
CONFIGURATION
2
5
Outside the panel
To pull the power line and communication cable out of the panel, make two pullout holes away from each other and pull
the cables through.
Putting both cables through the same pullout hole will increase noise interference.
Power line
Power line
6
Connection
cable
INSTALLATION
Connection
cable
Pullout hole
Pullout hole
Keep the power line and communication cable inside the duct at least 100mm away from each other.
If that is not possible, the use of a metal separator inside the duct can reduce noise interference.
Power line
Wiring duct
7
Separator
Signal line
8
OPTION
Power line
WIRING
100mm or more
Signal line
UL, cUL
STANDARDS AND
EMC DIRECTIVE
7.2.1
7. WIRING
7.2 Wiring inside and outside the panel
7-5
7.2.3
Attaching surge killers to control equipment
If communication errors happen in synch with the on/off signals from certain control equipment (referred to as "load"
hereafter) such as no fuse breakers, electromagnetic contactors, relays, solenoid valves, and induction motors, surge
noise interference is suspected.
If this problem happens, keep the ground cable and communication cable away from the load.
If that is not possible, an installation of a surge killer will help reduce noise interference.
Place the surge killer as close to the load as possible.
Remedy for AC inductive load
Keep the ground cable and
communication cable away
from each other.
C
L:Load
Output
R
Output equipment
such as PLC output unit
AC
Place the surge killer near the load.
Remedy for DC inductive load
Keep the ground cable and
communication cable away
from each other.
Output
D
DC
Output equipment
such as PLC output unit
7-6
7. WIRING
7.2 Wiring inside and outside the panel
L:Load
Place the surge killer near the load.
OPTION
OVERVIEW
1
8.1 SD Card
2
SYSTEM
CONFIGURATION
The SD card is used to transmit the OS or project data and to save the data of the alarm history function.
For details, refer to the following.
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
Applicable SD card
3
The following SD cards are applicable for GOT.
Description
L1MEM-2GBSD
SD memory card 2GB
L1MEM-4GBSD
SDHC memory card 4GB
-
Commercially-available SD card*1
8.1.2
Some models with the operations checked by our company are usable.
For the operation-checked models, refer to "Operation Check Results of Third Party SD Cards on GT14 Model" (Hime-T-P-0089)
separately available, or contact your local distributor.
Installing and removing procedures of the SD card
5
Install/remove the SD card with the power supply of GOT is OFF or SD card access switch is "OFF".
 Installing
Set the SD card access switch of the GOT to "OFF", and
make sure
that the SD card access LED turns off.
When the SD card access LED turns off, the SD card
can be installed even during the GOT power on.
6
INSTALLATION
1.
4
PARTS NAME
*1
SPECIFICATIONS
Model name
UL, cUL
STANDARDS AND
EMC DIRECTIVE
8.1.1
3.
Insert the SD card into the SD card interface with its front
side (nameplate side) outside.
Turn the SD card access switch on.
After the SD card access switch is turned on, the SD
card can be used.
7
8
OPTION
2.
SD card
front face
WIRING
8.
8. OPTION
8.1 SD Card
8-1
 Removing
1.
2.
Set the SD card access switch of the GOT to "OFF."
Make sure that the SD card access LED turns off.
When the SD card access LED turns off, the SD card can
be installed or removed even during the GOT power on.
Push-in the SD card once and leave your finger, then
remove the SD card.
POINT
Precautions for removing the SD card
(1) While the SD card access LED is on, do not install/remove the SD card or power off the GOT.
To do so may cause data corruption or malfunction.
(2) When ejecting the SD card, support it by hand since it may pop out.
Failure to do so may cause a fall of the SD card leading to failure or damage of the card.
8-2
8. OPTION
8.1 SD Card
1
8.2 USB Memory
OVERVIEW
The USB memory is used to transmit the OS or project data and to save the data of the alarm history function.
For details, refer to the following.
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
2
SYSTEM
CONFIGURATION
Applicable USB memory
The following USB memory is applicable for GOT.
Model name
Commercially-available USB memory*1
*1
8.2.2
Description
Some models with the operations checked by our company are usable.
For the operation-checked models, refer to "List of valid devices applicable for GOT1000 series" (T10-0039) separately available,
or contact your local distributor.
Installing and removing procedures of the USB memory
When USB memory is accurately inserted to the USB interface, the GOT automatically recognizes it.
For removing methods of the USB memory, refer to the following.
3
SPECIFICATIONS
8.2.1
4
PARTS NAME
13.2.9 USB device status display
UL, cUL
STANDARDS AND
EMC DIRECTIVE
5
INSTALLATION
6
WIRING
7
OPTION
8
8. OPTION
8.2 USB Memory
8-3
8.3 Battery
The battery backs up clock data and data stored in the built-in RAM (D drive) including alarm history, recipe data, time
action setting value, advanced alarm, advanced recipe, logging, hard copy, and SRAM user area. A battery is installed to
GT14 when GT14 is shipped from the factory.
8.3.1
Applicable battery
The following battery is applicable for GT14.
8.3.2
Model name
Description
GT11-50BAT
Battery for clock data, alarm history, recipe data, time action setting value, advanced alarm,
advanced recipe, logging, hard copy, and SRAM user area backups
Battery specifications
The following describes the battery specifications.
Item
Specifications
Model name
GT11-50BAT
Type
Manganese dioxide lithium primary battery
Initial voltage
3.0V
Life
Approx. 5 years (Operating ambient temperature of 25
Application
)
For clock data, alarm history, recipe data, time action setting value, advanced alarm,
advanced recipe, logging, hard copy, and SRAM user area backups
POINT
For the battery directive in EU member states, refer to the following.
17.4 ■Handling of Batteries and Devices with Built-in Batteries in EU Member States
POINT
Battery life and replacement time
(1) Battery life reference: Approx. 5 years (Operating ambient temperature of 25
Battery replacement time reference: 4 to 5 years
The battery is susceptible to natural discharge. Order one when necessary.
(2) Check if the battery condition is normal within the utility.
For details of battery status display, refer to the following.
11.1 Display Setting
8-4
8. OPTION
8.3 Battery
)
8.3.3
1
Battery replacement procedure
Open the battery cover of the GOT.
Remove the old battery from the GOT.
2
Turn the GOT power off.
Connector
5.
Disconnect the old battery connector and insert
the new battery connector within 30s.
Install a new battery to the GOT and close the
battery cover.
3
SPECIFICATIONS
4.
Battery cover
SYSTEM
CONFIGURATION
1.
2.
3.
Connector
4
Check if the battery condition is normal with the
utility.
For details of battery status display, refer to the
following.
12. CLOCK SETTINGS AND BATTERY
STATUS DISPLAY (TIME SETTING AND
DISPLAY)
PARTS NAME
Turn the GOT power on.
5
INSTALLATION
6
WIRING
7
8
OPTION
6.
7.
UL, cUL
STANDARDS AND
EMC DIRECTIVE
Battery cover
OVERVIEW
Replace battery periodically at intervals of 4 to 5 years as reference.
8. OPTION
8.3 Battery
8-5
8.4 Protective Sheet
The protective sheet is used to protect the operation surface from damage or dirt when the touch key of GOT display
section is operated.
For the GOT, the protective sheet is attached for transportation. (It is different from the one described in this chapter.)
8.4.1
Applicable protective sheet
Product name
Protective sheet
Model name
Description
GT14-50PSCB
Clear 5 sheets
GT14-50PSCB
Antiglare 5 sheets
GT14-50PSCW
5.7" protective sheet
GT14-50PSGW
8.4.2
Clear (Frame: white) 5 sheets
Antiglare (Frame: white) 5 sheets
Installing procedure
1.
2.
3.
4.
If the protective sheet has been already attached to the
GOT, remove the old one from the GOT display section
holding the lower right corner.
If the protective sheet for transportation is attached to the
GOT, remove it too.
Remove the release paper from the back of a new
protective sheet. Do not remove the protective film.
Make sure to fit the sheet on the GOT without wrinkles or
air between the sheet and the GOT.
Remove the protective film from the protective sheet.
When the user continues using the GOT with the protective
film, the film may not be removed.
POINT
Replacement time of protective sheet
Check the status of the protective sheet visually by the daily inspection.
The visibility becomes worse when there is too much dirt and cracks, causing malfunction. Proceed replacement
promptly.
8-6
8. OPTION
8.4 Protective Sheet
Use of the protective cover for oil improves waterproof property, oil resistance, and chemical resistance of the GOT.
8.5.1
Applicable protective cover for oil
2
The following protective cover for oil is applicable for GT14.
Model name
Protective cover for oil
GT05-50PCO
8.5.2
Description
SYSTEM
CONFIGURATION
Product name
OVERVIEW
1
8.5 Protective Cover for Oil
5.7" protective cover for oil
Installing procedure
A protective film is attached on the display area when the GOT is shipped. Make sure to remove the protective film
before attaching the protective cover for oil.
For attaching the protective cover for oil to the GOT already mounted on the control panel, follow the procedures as
below.
• Remove the GOT from the control panel.
Make sure to externally shut off all phases of the power supply and remove all cables from the GOT in advance.
• Clean dirt off surfaces of the GOT and control panel.
GOT
1.
Position the POWER LED frame of the cover to the
POWER LED on the GOT front face, and the direction
of the cover is decided.
Protective Cover For oil
2.
One corner of the cover is pulled outside, and it hangs
it on the corner of the front panel of GOT.
5
6
INSTALLATION
Please do not pull the oil cover
more than the necessity,
and do not bend it extremely.
The seat part and the rubber part
in the display part might flake off.
4
PARTS NAME
Before attaching protective cover for oil
UL, cUL
STANDARDS AND
EMC DIRECTIVE
POINT
SPECIFICATIONS
3
Protective Cover For oil
7
The corner is hung.
WIRING
GOT
OPTION
8
8. OPTION
8.5 Protective Cover for Oil
8-7
The corner on the left is hung and the oil cover is hung
from A side to D side on the starting point sequentially.
3.
A
B
The oil cover was hung and the edge of the oil cover is
sequentially obtained and obtain the oil cover to cover
rubber packing parts in the back of GOT of the front
panel.
(From A side to D side, in the direction of the arrow)
D
C
4.
Make sure that corners of protective
cover for oil match those of GOT front.
5.
Protectivecover
for oil
Panel cut
dimensions
Please confirm all surroundings. Check whether the
rubber packing is fitted correctly into the groove on the
under side of the GOT front panel, and then whether
the protective cover for oil securely covers the rubber
packing part to prevent invasion of liquids into the
board.
Mount the GOT onto the control panel. When the
control panel is dirty, clean the control panel. The
panel cutting dimensions and mounting screw
tightening torque with the protective cover for oil are
the same as those without the cover.
Mounting metal fixture
Control panel
POINT
(1) Precautions on installation
Tighten the mounting screws within the specified torque range.
• Specified torque range (0.3 to 0.5N·m)
Undertightening can cause a drop. Also, undertightening can disable waterproof or oil proof effect.
Overtightening can cause a drop, short circuit or malfunction due to the damage of the GOT or the mounting
fixtures. Also, "distortion" of the GOT or the panel may disable waterproof or oil proof effect.
(2) Precautions for protective cover for oil
• The protective cover for oil is a consumable product.
Check the cover for scratch, damage or dirt at regular intervals, and replace with new one if necessary.
• Do not push the protective cover for oil with pointed tools, including mechanical pencils and screwdrivers.
Doing so causes scratches and damages of the cover.
• Do not clean the protective cover for oil with bleaches, thinners, organic solvents, corrosive chemicals, and
others. Doing so causes changes in shape and color of the cover.
• When the protective cover for oil is attached to the GOT, do not stretch and bend the cover too much. Doing
so may cause a separation between the sheet and rubber.
• Do not place or use the protective cover for oil in direct sunshine.
• When the protective cover for oil gets dusts, wipe the dusts off with a damp cloth.
• Do not do a frequent detaching the protective cover for oil.
It causes deterioration in the oil performance and the medicine performance.
• It is not the one to guarantee all customer's environments.
Moreover, it is not likely to be able to use it in the environment to which oil splashes for a long time and the
environment with which Oilmist is filled.
8-8
8. OPTION
8.5 Protective Cover for Oil
The USB environmental protection cover protects the USB connector on the front face of GOT from dust, water, and oil.
The GOT is installed with the USB environmental protection cover at factory shipment.
Replace when damage and deterioration are caused.
Applicable USB environmental protection cover
The following USB environmental protection cover is applicable for GT14.
Model name
USB environmental
protection cover
GT14-50UCOV
Environmental protection cover for USB interface on the main unit front panel (conforming to IP67f)
3
Installing procedure
USB environmental
protection cover
Open
Mounting screw
1.
2.
3.
4.
5.
SPECIFICATIONS
8.6.2
Description
Turn the GOT power off.
Disconnect the USB cable from the GOT if one is
connected.
4
Open the USB environmental protection cover
equipped with the GOT and remove the mounting
screws.
Remove the old USB environmental protection cover
from the GOT to replace it with the new USB
environmental protection cover.
Fix the projection of the new USB environmental
protection cover to be fitted into the hole of the GOT,
tighten the mounting screw in the specified torque
range, then install it to the GOT.
Tighten the mounting screws in the specified torque
range.
Not doing so may cause a damage or a drop.
Specified torque range: 0.36 to 0.48N·m
PARTS NAME
Product name
SYSTEM
CONFIGURATION
2
5
UL, cUL
STANDARDS AND
EMC DIRECTIVE
8.6.1
OVERVIEW
1
8.6 USB Environmental Protection Cover
6
INSTALLATION
Mounting screw
M3 x 6 pan head screw
WIRING
7
M3 x 6 pan head screw
POINT
8
Precautions when the USB environmental protection cover is opened
OPTION
Environmental protective structure of USB interface is "IP2X" when the USB environmental protection cover is
opened.
8. OPTION
8.6 USB Environmental Protection Cover
8-9
8.7 Stand
Stand is used to fix the GOT to standing status in order to debug the monitor screen data easily.
8.7.1
Applicable stand
The following stand is applicable for GT14.
Product name
Model name
Stand
8.7.2
GT05-50STAND
Description
Stand for 5.7" (for GOT1000 series)
Installing procedure
Adjust to
45 , 55 , 65 or 75 .
1.
Adjust the mounting angle of GOT with the angle
adjusting fitting of the stand.
Angle adjusting fitting
2.
GOT
mounting face
Put the GOT into the stand from the stand front side
and fix it using the mounting fixtures.
For how to mount the GOT, refer to the following.
6.5 Installation Procedure
For a detail of the stand, refer to the following.
GOT1000 STAND User's Manual
8 - 10
8. OPTION
8.7 Stand
GT10-9PT5S type connector conversion adapter enables an easy crossover wiring for the multi-drop-connected GOTs.
For the wiring between the connector conversion adapter and the controller, refer to the following manual.
GOT1000 Series Connection Manual (Mitsubishi Products) for GT Works3
OVERVIEW
1
8.8 Connector Conversion Adapter
2
Applicable connector conversion adapter
SYSTEM
CONFIGURATION
8.8.1
The following connector conversion adapter is applicable.
Model name
Description
GT10-9PT5S
For GOT multi-drop connection
3
1.
Turn the GOT power off.
Connect the connection conversion adapter to the RS422/485 interface on the GOT.
4
PARTS NAME
2.
SPECIFICATIONS
Installing procedure of connector conversion adapter
5
UL, cUL
STANDARDS AND
EMC DIRECTIVE
Fix the connection conversion adapter to the GOT
using the provided M3 tapping screws.
Tightening torque: 0.3 to 0.6 N•m
INSTALLATION
6
7
WIRING
3.
8
OPTION
8.8.2
8. OPTION
8.8 Connector Conversion Adapter
8 - 11
8.9 Serial Multi-Drop Connection Unit
8.9.1
Serial multi-drop connection unit
GOT serial multi-drop connection is a communication method for 1:N communication by connecting multiple GOTs to
one PLC, using the GT01-RS4-M serial multi-drop connection unit.
For details of GOT multidrop connection, refer to the following.
GOT1000 Series Connection Manual (Mitsubishi Products) for GT Works3
Serial multi-drop connection unit
Connect to the PLC
RS-485 cable
8.9.2
Applicable serial multi-drop connection unit
The following serial multi-drop connection unit is applicable.
8.9.3
Model name
Description
GT01-RS4-M
For GOT multi-drop connection
Installation
 Installed with DIN rail
Install the serial multi-drop connection unit with its hook (1 place) using the DIN rail.
• Applicable DIN rail DIN46277 (width: 35mm)
(Install the DIN rail with screws at intervals of 150mm.)
 Directly installed to panel
Install the serial multi-drop connection unit to the panel using 4.5mm holes (2 places).
8 - 12
8. OPTION
8.9 Serial Multi-Drop Connection Unit
1
Parts name
1)
Protective cover is installed
Protective cover is removed
5)
2)
8)
4)
90 (3.55")
72 (2.84")
OVERVIEW
8.9.4
2
SYSTEM
CONFIGURATION
3)
7)
5)
2- 4.5
3
12)
SPECIFICATIONS
9)
11)
4
80
57 (2.25")
65 (2.56")
10)
POWER
Lit in green when the power is properly supplied.
SD
Lit in green when the data is being sent to PLC.
RD
Lit in green when the data is being received from PLC.
ERROR
Lit or blinking depending on the status.
5
3)
Terminating resistor selector switch
Can be selected among 110 , OPEN, and 330
4)
Connector for the PLC communication
D-Sub 9pin (Male), for RS-232 connection
5)
Connector selection switch for the PLC
communication
Switch for selecting RS-422 or RS-232 (set to "RS-422" by default)
6)
USB port
For connecting a PC (for changing the communication driver)
7)
Connector for the PLC communication
D-Sub 9pin (Female), for RS-422 connection
8)
Protective cover
Protects unused D-sub connector, USB port, and switches.
9)
Terminal block for the serial multi-drop
communication
Terminal block 5-pin (with a protective cover) M3 Tightening torque 0.5 to 0.6N•m
10)
Power supply connector
24VDC power supply connector insertion point (A dedicated cable is included.)
11)
Slider for installing the DIN rail
12)
Mode selection switch
(Slide switch)
8.9.5
UL, cUL
STANDARDS AND
EMC DIRECTIVE
LED
Installation hole (2-Φ4.5)
(set to "OPEN" by default).
6
INSTALLATION
2)
Installation hole for the main unit
Description
7
Do not operate.
(Set to right by default. When set to left, the module does not operate normally.)
WIRING
1)
Name
Caution for compliance with EMC Directive
8
Please use the serial multi-drop connection unit while installed in conductive shielded control panels.
Programmable logic controllers are open-type devices that must be installed and used within conductive control panels.
Please secure the control panel lid to the control panel (for conduction).
Installation within a control panel greatly affects the safety of the system and aids in shielding noise from the serial multidrop connection unit.
8. OPTION
8.9 Serial Multi-Drop Connection Unit
8 - 13
OPTION
No.
PARTS NAME
Unit: mm (inch)
8.10 Panel-Mounted USB Port Extension
GT14-C10EXUSB-4S panel-mounted USB port extension is a waterproof extension cable of the USB.
It is used to pull out the USB interface (host) on the back of GT14 to the surface of the control panel.
8.10.1
Applicable panel-mounted USB port extension
The following panel-mounted USB port extension is applicable for GT14.
8.10.2
Model name
Description
GT14-C10EXUSB-4S
Panel-mounted USB port extension
Parts name
The following shows the parts name of panel-mounted USB port extension.
Cap installation chart
Waterproof cap
Cable
Ferrite core
USB plug
8.10.3
Model name label
Seal
Nut
Installing procedure
 Installed to panel
Install the panel-mounted USB port extension as follows with attention to a curve or a distortion of waterproof cap,
seal, and nut.
20.8±0.1
(0.82"±0.01)
Panel thickness: 2 to 4mm
(0.08 to 0.16inch)
Nut
Seal
Waterproof
cap
19.4±0.1
(0.77"±0.01)
Unit: mm (inch)
Panel Cutting Dimensions
•
•
•
•
8 - 14
The panel thickness is 2.0 to 4.0mm.
For panel-mounted USB port extension, the panel surface with waterproof cap is compatible with IP67f.
Tightening torque of nut is 0.294 to 0.343N•m. Overtightening or undertightening may disable the waterproof effect.
Tighten the waterproof cap properly when the cable is not used.
8. OPTION
8.10 Panel-Mounted USB Port Extension
(1) Run power lines, servo amplifier drive wires, and panel-mounted USB port extensions so that they do not cross
each other.
(2) Install the panel-mounted USB port extension away from noise sources such as equipment.
(3) Do not twist, bend at a sharp angle or a right angle, and stretch the panel-mounted USB port extension since the
cable may be broken.
2
SYSTEM
CONFIGURATION
(4) Install it while considering the following control panel inside dimensions.
• Dimension between the back of the GOT and structures
OVERVIEW
1
 Precautions on installing the panel-mounted USB port extension
3
SPECIFICATIONS
80 (3.15")
or more
PARTS NAME
4
• Dimension of the protruding cable
80 (3.15") or more
UL, cUL
STANDARDS AND
EMC DIRECTIVE
5
6
INSTALLATION
(5) Insert the USB plug part of the tip of the panel-mounted USB port extension securely to the USB port of the
GOT.
Since the USB plug part may be inserted loosely or unplugged by power of vibrations, impacts, or pulling, fix the
cable to the structures inside the panel or the preventive hole from removing for the USB cable of the GOT main
unit by using the banding band or others.
WIRING
7
8
OPTION
(6) Use the product after checking that the functions and performances operate correctly.
8. OPTION
8.10 Panel-Mounted USB Port Extension
8 - 15
8.11 RS-232/485 Signal Conversion Adapter
GT14-RS2T4-9P type RS-232/485 signal conversion adaptor enables conversion of RS-232 communication interface to
RS-485 communication interface.
For the wiring between the RS-232/485 signal conversion adapter and the controller, refer to the following manual.
GOT1000 Series Connection Manual (Mitsubishi Products) for GT Works3
8.11.1
Applicable RS-232/485 signal conversion adapter
The following RS-232/485 signal conversion adaptor is applicable.
8.11.2
Model name
Contents
GT14-RS2T4-9P
For GOT multi-drop connection, multi-channel function connection,
temperature controller connection, and MODBUS(R)/RTU connection
Installing procedure of RS-232/485 signal conversion adapter
1.
2.
3.
Turn the GOT power off.
Connect the RS-232/485 signal conversion adapter to
the RS-232 interface on the GOT.
Fix the RS-232/485 signal conversion adaptor to the
GOT using the provided M3 tapping screws.
Tightening torque: 0.3 to 0.6 N•m
POINT
5V power supply
(1) To use the RS-232/485 signal conversion adaptor, select [Communication Setting]
[Communication
Setting]
[5V power supply]
[Yes] on the utility screen of GT14.
5V power supply is a function that supplies electrical power to the RS-232/485 signal conversion adaptor.
It cannot be used in other controllers. For details on the 5V power supply, refer to the following.
10.1.3 Communication setting contents
(2) [5V power supply] can be set with the GT 14 hardware version B or later.
In the hardware version A, since 5V power is always supplied, this setting operation is invalid.
(3) To use the RS-232/485 signal conversion adaptor, select CoreOS of version V05.28.00AP or later and the
standard OS of version V05.28.00 or later for GT14. For details on the version confirmation, refer to the
following.
13.1.2 OS version confirmation
8 - 16
8. OPTION
8.11 RS-232/485 Signal Conversion Adapter
UTILITY FUNCTION
9
UTILITY FUNCTION
9.
Utility is a function, which carries out connection of GOT and PLC, screen display and operation method settings,
program/data control and self-check etc.
For the utility function list, refer to the following.
10
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
9.2 Utility Function List
9.1 Utility Execution
For utility execution, utility has to be displayed by installing BootOS and Standard monitor OS in the C drive (Flash
memory).
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
11
There are following three types for the installing Standard monitor OS methods.
GOT
USB interface or
Ethernet interface or
RS-232 interface *1
GT Designer3
Installed directly from GT Designer3
12
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
1) GT Designer3
BootOS or Standard monitor OS installation
SD card
2) GT Designer3
or
USB memory
GOT
BootOS or Standard
monitor OS installation
OS file
write
When GOT is remote, installed easily
using the SD card or USB memory
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
GT Designer3
13
Install the SD
card or USB
memory in GOT
SD card or
USB memory *1
SD card
or
GOT
USB memory
OS file
upload
BootOS or Standard
monitor OS installation
SD card or
USB memory *1
*1
Install OS from GOT to GOT using
SD card or USB memory
14
Install the SD
card or USB
memory in GOT
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
3) GOT
When installing the BootOS and standard monitor OS, standard monitor OS has to be installed in GOT in advance.
For the installation which uses GT Designer3, refer to the following.
GT Designer3 Version1 Screen Design Manual (Fundamentals)
15
CLEANING DISPLAY
SECTION (CLEAN)
For the installation which uses GOT, refer to the following.
16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
9. UTILITY FUNCTION
9.1 Utility Execution
9-1
9.2 Utility Function List
The items in the following list can be set/operated on the utility screens.
Item
Functions overview
Reference
Assigning channel numbers and communication drivers to communication
interfaces
Communication setting
Communication setting
Setting communication parameters
Setting or deleting sequence program protection key words, canceling sequence
program protection status (When connecting to FX series CPU)
10.
10.
Setting whether to supply 5V power or not*1*2
Ethernet setting
Displaying the contents of Ethernet setting, changing the host
10.
Switching message languages
Setting the startup screen display time and screen saving time
Display
Setting the backlight to ON or OFF during screen saving
Setting the battery alarm display to ON or OFF
11.1
Adjusting brightness and contrast
Inverting colors
Setting the buzzer volume and window move buzzer
Setting the key sensitivity and key reaction speed
Changing security levels
Operation
GOT setup
11.2.4
Setting the utility call keys
11.2.5
Adjusting the touch panel
11.2.6
Setting the USB mouse and keyboard
11.2.7
®
11.2.8
VNC server function setting
Transparent mode
Backup/restoration
11.2
Setting the channel No. to be used for the communication for the FA transparent
function
Setting the storage locations for backup data and backup settings, and setting the
maximum number of backup data
Trigger backup settings
11.3
11.4
Setting the CPU No. setting at backup to "YES" or "NO"
Behavior of duplicate IPs
Setting the GOT operation when a device with the same IP address as that of the
GOT is added to the network afterwards
11.5
License management
Displaying the screen for license registration and deregistration
11.6
Selecting a base clock
Displaying the clock current time
Time setting & display
12.
Setting the clock current time
Displaying the battery status
OS information
Alarm information
Installing or uploading OS, displaying OS property, checking OS data
Deleting and copying alarm log files
Converting alarm log files in G1A format
CSV or TXT format
Downloading, uploading, deleting or copying project files, displaying project file
property, checking project file data
13.2.3
Hard copy information
Deleting or copying hard copy files, changing hard copy file names
13.2.4
Advanced Recipe information
Logging information
9-2
13.2.2
Project information
Converting advanced recipe files in G1P format
Program/data control
13.2.1
CSV or TXT format
Converting CSV or TXT format
Advanced recipe files in G1P format
Deleting, copying or moving advanced recipe files, creating a new advanced
recipe file
Deleting or moving advanced recipe folders, changing advanced recipe folder
names, creating a new advanced recipe folder
Writing, reading or matching record data and deleting device values with the
advanced recipe record list
Converting logging files in G1L format
CSV or TXT format
Deleting, copying or moving logging files, changing logging file names
Deleting logging folders or creating a new logging folder
13.2.5
13.2.6
Memory card format
Formatting a SD card or USB memory, internal SRAM
13.2.7
Memory information
Displaying the available memory of the GOT
13.2.8
USB device status display
Displaying the status of USB device
13.2.9
9. UTILITY FUNCTION
9.2 Utility Function List
13.2.10
GOT data package acquisition
Copying the OS, special data, and project data to a SD card or USB memory
13.2.11
Device monitor of PLC, test function, present value change of the buffer memory
monitor and the buffer memory of intelligent module
14.1.1
Debug A list editor
Debug & self check
Self
check
Sequence program and parameter change of ACPU
14.1.2
FX list editor
Sequence program and parameter change of FX PLC
14.1.3
Backup/restoration
Executing backups, executing restorations, and deleting backup data
14.1.4
Memory check
Memory check of A drive, C drive, D drive, and E drive
14.2.1
Drawing check
14.2.2
Display check
Font check
14.2.3
Touch panel check
Touch panel operation check
14.2.4
I/O check
Connected target confirmation, self-loopback check
14.2.5
Ethernet status check Sends a ping to check the Ethernet connection status
14.2.6
System alarm display
Displaying GOT errors and CPU errors, resetting GOT errors
14.3
GOT start time
Displaying GOT start date and time, current time, accumulated operating hours
14.4
Clean
Displaying the screen for cleaning the display
15.
*1
Do not use this function for other than 5V power supply to the RS-232/485 signal conversion adaptor.
*2
7.11 RS-232/485 signal conversion adapter
[5V power supply] can be set with the GT 14 hardware version B or later. In the hardware version A, since 5V power is always
supplied, this setting operation is invalid.
9
UTILITY FUNCTION
SRAM control
Confirming the SRAM user area usage, backing up or restoring the data in the
SRAM user area, and initializing the SRAM user area
System monitor
Clean
Reference
10
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
Program/data control
Functions overview
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
Item
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
13
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
9. UTILITY FUNCTION
9.2 Utility Function List
9-3
9.3 Utility Display
To display setting screens for each utility, the main menu must be displayed first.
(1)
(1)
(2)
(2)
(1) Main menu
The menu items that can be selected from the GOT utility are displayed.
Touching a menu item in the main menu displays the setting screen or following selection screen for the item.
(2) System message switch button
This button switches the language used for the utility screen and system alarms.
Touching the [Language] button displays the Select Language screen.
1.
2.
9-4
Touch the button of a desired language and then [OK] button, and the language is selected.
Touching the [
] button restarts the GOT and the language of the utility is switched to the selected one.
9. UTILITY FUNCTION
9.3 Utility Display
POINT
When starting the GOT without selecting any language or the selected language and the installed fonts are not
matched.
10
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
The following screen is displayed.
Touching the button of a desired language restarts the GOT and the language is switched to the selected one.
UTILITY FUNCTION
9
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
11
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
(1) Selectable languages
The system message switch button is displayed only for the selectable languages.
The selectable languages differ depending on the fonts installed in the GOT.
For the relation between the selectable languages and the fonts, refer to the following.
GT Designer3 Version1 Screen Design Manual (Fundamental) 2.5 Specifications of Applicable
Characters
(2) System language switching using the device
The system language can be switched using the system language switching device set with GT Designer3.
For the setting method of the system language switching device, refer to the following.
GT Designer3 Version1 Screen Design Manual (Fundamental)
4.3 Language Switching Device Setting (GOT Environmental Setting: Language Switching)
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
HINT
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
9. UTILITY FUNCTION
9.3 Utility Display
9-5
9.3.1
Display operation of main menu
The following four types of operation can display the main menu.
(Display the main menu after installing the Standard monitor OS from GT Designer3 to the built-in flash memory of the
GOT.)
(1) When project data is undownloaded
After the GOT is turned on, a dialog box for notifying of absence of project data is displayed. After the dialog box
is displayed, touch the OK button to display the main menu.
GOT power on
Touch the OK button.
(2) When touching menu call key
Touching the menu call key while user-created screen is displayed displays the main menu.
The menu call key is set in the position on the GOT screen upper left corner at factory shipment.
Horizontal display
*
Length display *
The utility screen is a factory installed horizontal format screen that cannot be edited.
The menu call key can be set by the GOT utility or GT Designer3.
For menu call key setting, refer to the following.
• 11.2.5 Utility Call Key Setting
• GT Designer3 Version1 Screen Design Manual (Fundamental)
4.9 GOT Display and Operation Setting (GOT Environmental Setting: GOT Setup)
POINT
(1) Prohibited simultaneous 2-point presses
Do not touch 2 points or more on the GOT screen simultaneously. Touching 2 points or more simultaneously
may activate a part other than the touched point.
(2) Pressing time of the utility call key
When having set [Pressing time] of the menu call key setting screen to other than "0 (s)", keep pressing the
touch panel for the period set to [Pressing time] or more before leaving the finger from the touch panel.
For menu call key setting, refer to the following.
11.2.5 Utility Call Key Setting
(3) When the utility call key is set to the zero point
Even when the utility call key is set to the zero point, you can display the main menu using either of the
following two operations:
• Pressing the special function switch set on the user-created screen
• Keeping pressing the upper left corner while the [Booting.] message is displayed after powering up.
9-6
9. UTILITY FUNCTION
9.3 Utility Display
Touching the special function switch (utility) while user-created screen is displayed displays the main menu.
The special function switch (utility) can be set as a touch switch that is displayed on a user-created screen by
GT Designer3.
UTILITY FUNCTION
9
(3) When touching special function switch (utility)
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
Special function switch
(Utility)
For the details of the special function switch, refer to the following.
(4) When powering ON the system
12
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
The [Booting.] message is displayed after powering up. After that, keep pressing the upper left corner to display
the main menu.
If the upper left corner is pressed before the display of the [Booting...] message, the OS installation function
starts. Therefore, press the upper left corner after the [Booting...] message is displayed.
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
11
GT Designer3 Version1 Screen Design Manual (Functions)
Booting.
When limiting the display and operation of the utility
When limiting the display and operating users, set a password to the GOT using the GT Designer3. If a user tries to
display the main menu of the utility, the password input screen is displayed.
For details on setting passwords, refer to the following.
GT Designer3 Version1 Screen Design Manual (Fundamentals)
14
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
POINT
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
13
Press the screen upper left corner
during [Booting...] message display.
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
9. UTILITY FUNCTION
9.3 Utility Display
9-7
9.3.2
Utility basic configuration
The basic configuration of the screen is as follows.
Title display
Close/Return button
Scroll key
Screen
(1) Title display
The screen title name is displayed in title display part.
Title display
Title display
(2) Close/Return button
When a middle screen of the layers is displayed, if the [ ] (Close/return) button in the right corner of screen is
touched, returns to the previous screen.
If this button is touched when directly displayed from monitor screen, the screen is closed and returns to monitor
screen.
(3) Scroll button
For screens in which the content does not fit on one screen page, there is a right or down scroll button on the
screen.
Scroll one line/column
Scroll window
9-8
9. UTILITY FUNCTION
9.3 Utility Display
9
Basic operation of settings change
UTILITY FUNCTION
9.3.3
 Change of setting value
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
Select button
Setting item
Select button
(1) Setting item, select button
Touch the select button to change the settings.
The setting methods differ depending on the setting items.
The following types of setting method are available.
12
(a) Switch the setting value.
Touch the button to switch the setting value as shown in ON
OFF .
(b) Enter the setting value with a keyboard.
It is a key for inputting the numerical value. Touching this button displays a keyboard on the GOT screen.
For the operation of keyboard, refer to the next page.
13
Move to another setting screen.
Touching this button moves to another setting screen.
For the setting method of each setting item, refer to the setting operation of each setting screen.
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
(c)
(2) [OK] button, [Cancel] button, [ ] (Close/Return) button
Reflect or cancel the changed settings.
(a) [OK] button
Touching this button reflects the changed settings.
14
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
(b) [Cancel] button
Touching this button cancels the changed settings and return to the previous screen.
[ ] (Close/Return) button
Touching this button closes the screen. Depending on the setting item, the GOT restarts.
If [ ] button is touched without touching [OK] button, the following dialog box will be displayed.
(If the settings are not changed, the dialog box is not displayed.)
Operate following the message of the dialog box.
CLEANING DISPLAY
SECTION (CLEAN)
15
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
(c)
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
Setting item
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
11
9. UTILITY FUNCTION
9.3 Utility Display
9-9
 Keyboard operation
1.
2.
Touch the numerical value to be changed.
Keyboard for numerical input is displayed and cursor is displayed simultaneously.
The key board display position changes by the position of numerical value touched.
(At the time of numerical input, displayed in the position which will not interrupt the inputting.)
Cursor
Keyboard
3.
Input numeric with keyboard.
• [0] to [9] Key: Input the numeric.
• [Enter] Key: Completes numeric input and closes the keyboard.
• [Cancel] Key: Cancels numeric input and closes the keyboard.
•
Key: Moves the cursor to the right or left side. (Available only if any selectable item is at the right/left side
of the cursor.)
• [Del] Key: [Del] key is used when canceling the input by 1 character.
• [*] key and the key which is not mentioned do not function.
4.
9 - 10
Touching [Enter] key completes numeric input and closes keyboard.
9. UTILITY FUNCTION
9.3 Utility Display
10. COMMUNICATION INTERFACE
SETTING (COMMUNICATION
SETTING)
UTILITY FUNCTION
9
Description
Reference
The setting contents of the communication interface can be checked or changed.
Ethernet setting
10-1
Whether to supply 5V power or not can be set.
10-1
The contents of the Ethernet setting can be checked and the host can be changed.
10-15
10.1 Communication setting
10.1.1
Communication setting functions
Function
12
Description
Channel-Driver assign
Change the assignment of channel No. and communication driver name.
Assign Ethernet I/F
Change the assignment of channel No. and communication driver name of the device connected using the
Ethernet interface.
Channel No. (Ch No.) setting
Set the channel numbers of the communication interface (Standard interface).
Communication parameters setting
Set communication parameters of communication devices.
5V power supply
Set whether to supply 5V power or not when the RS-232/485 signal conversion adaptor is used.
13
Communication setting
Main menu
9.3 Utility Display)
Touch
[Comm.setting]
14
Touch
[Communication setting]
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
(
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
Display operation of Communication Setting
15
CLEANING DISPLAY
SECTION (CLEAN)
Communication setting
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
10.1.2
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
Communication Setting
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
Function
10
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
In [Communication Setting], the communication interface names and the related communication channel,
communication driver names display and channel numbers are set.
Moreover, in [Communication Detail setting], the communication interface details are set. (Communication parameters
setting)
10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)
10.1 Communication setting
10 - 1
10.1.3
Communication setting contents
This section describes setting items and display contents for Communication Setting.
(2)
(4)
(2)
(3)
(3)
(6)
(4)
(2)
(4)
(2)
(4)
(3)
(5)
(1)
(1) Channel-Driver assign
Channel No. can be assigned to the communication driver installed in the GOT.
(a) Not writing [Communication Setting] in drawing software
Without writing [Communication Setting] in drawing software, communication with a controller is available
after assigning the channel No. with this function.
10.1.4 ■ Channel-Driver assign operation
(b) When changing the assignment of the communication driver to the channel in the Utility
Without using drawing software, the assignment of communication drivers to channels can be changed.
(When changing a communication driver, the alternative communication driver has to be installed in GOT in
advance.)
(2) Standard interface display BOX
Display the communication interface included as standard in GT14. There are the following 4 types.
[GOT front face]
USB interface (Standard interface)
[GOT rear face]
RS-422 interface (Standard interface)
RS-232 interface (Standard interface)
Ethernet interface (Standard interface)
RS-232.................
RS-422/485..........
USB......................
Ethernet................
10 - 2
For communicating with PC (drawing software), bar code reader, RFID, controller or controller
For communicating with controller
For communicating with PC (drawing software)
For communicating with PC (drawing software) or controller
10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)
10.1 Communication setting
9
(3) Channel number specification menu BOX
Set when connecting with PC (drawing software).
*:
Set when using the function that uses the gateway function (when connection types except the
Ethernet connection is used for connecting to controllers), Ethernet download function.
10
• Fixed to 9 for the USB interface.
*1
Cannot be assigned with Ethernet I/F Assignment.
(4) Driver display BOX
The name of communication driver assigned to the channels or the driver set with the Communication Setting of
drawing software is displayed.
For details of drivers to be displayed, refer to the following manual.
GT Designer3 Version1 Screen Design Manual (Fundamentals)
Displays [None] in the driver display BOX in case of the following.
• The communication driver is not installed. (
13.2.1 OS information)
• In channel number specification menu BOX, [0] is set.
When the channel number is set to [9] to RS-232 interface, the communication driver [Host (PC)] or [Host
(model)] can be selected.
When the channel number is set to [9] to USB interface, the communication driver [Host (PC)] is automatically
assigned.
(5) Assign Ethernet I/F
The communication settings for the Ethernet connection can be made.
Only Ethernet interface built-in model can display this button.
Ethernet I/F Assignment can assign up to two channels per interface.
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
9*1:
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
Set when the communication interface is not used.
Set when connecting to a controller.
Set when connecting with a bar code reader or RFID.
12
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
0:
1, 2:
8:
UTILITY FUNCTION
Set channel No. to use with standard interface.
Refer to this section (4) for driver that can be assigned to each channel.
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
10.1.4 ■ Assign Ethernet I/F operation
(6) 5V power supply
Set the 5V power supply when using the RS-232/485 signal conversion adaptor.
10.1.4 ■ 5V power supply operation
POINT
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
Precautions for communications between GOT and controller
(1) Installing communication driver and downloading Communication Setting
The following below is required for the communication interface to communicate with the controller.
1)
Installing communication drivers (Up to 4 communication drivers)
2)
Assigning the channel number and communication driver for the communication interface
3) Downloading the contents (project data) assigned in 2).
Perform1), 2), 3) by drawing software.
CLEANING DISPLAY
SECTION (CLEAN)
15
GT Designer3 Version1 Screen Design Manual (Fundamentals)
(2) When Communication Setting has not been downloaded.
When [Communication Setting] has not been downloaded using drawing software, make the communication
settings in the drawing software or on the utility screen of the GOT.
10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)
10.1 Communication setting
10 - 3
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
For details, refer to the following.
10.1.4
Communication setting operation
 Channel-Driver assign operation
The following describes how to operate the Channel-Driver assign.
The example of changing to the direct CPU connection (Communication driver: [A/QnA/L/QCPU, LJ71C24,
QJ71C24]) for the GOT of the computer link connection (Communication driver: [AJ71QC24, MELDAS C6*]) is used.
POINT
Before starting operation
After Communication Setting is executed, the GOT automatically restarts.
If the project data is downloaded, GOT starts monitoring the communication device after restarting.
Execute this setting after carefully confirming the safety.
1.
2.
3.
Install communication driver [A/QnA/L/QCPU, L/
QJ71C24] to GOT.
(Download of [Communication Setting] from drawing
software is not required.)
After installing communication driver, touch the
[Channel Driver assign] button in [Communication
Setting].
Touch the [Change assignment] button on the
displayed screen as shown left.
As the communication driver ([A/QnA/L/QCPU, L/
QJ71C24]) installed in the GOT is displayed, touch it.
(Continued to next page)
10 - 4
10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)
10.1 Communication setting
5.
The screen returns to the [Channel-Driver assign]
screen and touch the [OK] button.
Touch [ ] button to return to the [Communication
Setting] screen.
9
UTILITY FUNCTION
4.
7.
8.
Confirm that the selected communication driver ([A/
QnA/L/QCPU, L/QJ71C24]) is assigned.
11
After confirming, touch the [OK] button.
Touching the [ ] button restarts the GOT and the
GOT operates with the changed settings.
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
6.
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
1.
2.
Touch channel number specification menu BOX
to be set.
The cursor for the channel number specification
menu BOX is displayed.
Simultaneously the keyboard for a numerical
input is displayed.
Keyboard
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
 Channel number setting operation
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
 Communication detail setting switching operation
If the driver display BOX is touched on the communication setting screen or Ethernet I/F assign screen, the screen
switches to the detailed setting screen of the related controller device.
(
10.2 Communication Detail Setting)
10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)
10.1 Communication setting
15
CLEANING DISPLAY
SECTION (CLEAN)
Input the channel number from the keyboard and
touch [Enter] key, and the value is defined.
Simultaneously, the name of the communication
driver corresponding to the channel number
assigned by drawing software is displayed in the
driver display BOX.
10 - 5
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
3.
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
 Assign Ethernet I/F operation
The following describes how to operate the Ethernet I/F assign.
The setting operation is same as that of the communication setting screen.
1.
2.
3.
4.
5.
6.
10 - 6
Touch the [Assign Ethernet I/F] button in
[Communication Setting].
After the screen shown left is displayed, touch the
channel number specification menu BOX when
changing the channel number.
(
10.1.4 ■ Channel number setting operation)
For changing the parameter settings, touch the driver
display BOX.
(
10.2Communication Detail Setting)
Touching the [OK] button reflects the changed
settings. Touching [ ] button returns the screen to
the [Communication Setting] screen.
Touch the [OK] button in the [Communication Setting]
screen.
Touching the [ ] button restarts the GOT and the
GOT operates with the changed settings.
10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)
10.1 Communication setting
9
UTILITY FUNCTION
 5V power supply operation
The following describes how to operate the 5V power supply.
1.
Touch the [5V power supply] button in
[Communication Setting].
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
2.
Touch the setting item of [5V power supply] when
using the RS-232/485 conversion adaptor. The
setting content is changed by touching.
(YES
NO)
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
11
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
Select [Yes] to change the setting of the 5V power
supply.
Touching the [OK] button reflects the changed
settings. Touching [ ] button returns the screen to
the [Communication Setting] screen.
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
3.
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
5.
Touch the [OK] button in the [Communication Setting]
screen.
Touching the [ ] button restarts the GOT and the
GOT operates with the changed settings.
10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)
10.1 Communication setting
10 - 7
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
4.
CLEANING DISPLAY
SECTION (CLEAN)
15
"*" indicating the setting to supply the 5V power
supply is displayed.
10.2 Communication Detail Setting
10.2.1
Communication detail setting functions
Function
Description
Communication parameters
setting
Set various communication parameters of communication devices. The settable parameters differ according to the
communication device.
Keyword Register
For the FX series PLCs, key word for protecting program in the PLC can be set.
Keyword Delete
For the FX series PLCs, key word for protecting program in the PLC can be deleted.
Keyword Clear
For the FX series PLCs, the program protection status in the PLC can be cancelled.
Keyword Protect
For the FX series PLCs with the 2nd keyword in use, the cancelled program protection in the PLC can be reactivated.
10.2.2
Display operation of Communication Detail setting
 Communication settings
1.
2.
Communication
parameter
Touch the driver display BOX of the communication
parameter to be set in the [Communication setting]
screen.
The screen switches to the [Communication Detail
setting] screen.
Set communication parameters from this screen.
For the setting change operation, refer to the
following.
9.3.3 Basic operation of settings change
POINT
Communication parameter setting by drawing software
Select [Common Settings]
[Communication Settings] from GT Designer3 to enter the communication
parameters for each communication driver.
When changing the communication parameters after downloading project data, change the setting at
communication detail setting of GOT.
GT Designer3 Version1 Screen Design Manual (Fundamentals)
10 - 8
10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)
10.2 Communication Detail Setting
Several drivers are assigned to the same Ethernet interface. However, only one GOT IP address is assigned per
interface.
By changing the settings of one interface, the GOT IP address, GOT port No. download, default gateway and subnet
mask settings of other drivers, which are assigned to the same interface, are also changed.
Touch the [Assign Ethernet I/F] button in
Communication Setting.
10
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
1.
UTILITY FUNCTION
9
 Assign Ethernet I/F
2.
Touch the driver display BOX of the communication
parameter to be set in Ethernet I/F assignment.
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
11
The screen switches to the [Communication Detail
setting] screen.
Set communication parameters from this screen.
For the setting change operation, refer to the
following.
9.3.3 Basic operation of settings change
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
3.
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
POINT
15
Communication parameter setting by drawing software
CLEANING DISPLAY
SECTION (CLEAN)
Select [Common Settings]
[Communication Settings] from GT Designer3 to enter the communication
parameters for each communication driver.
When changing the communication parameters after downloading project data, change the setting at
communication detail setting of GOT.
GT Designer3 Version1 Screen Design Manual (Fundamentals)
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)
10.2 Communication Detail Setting
10 - 9
10.2.3
Display contents of Communication Detail setting
The contents of communication detail setting varies according to driver type.
This section explains setting items different from the communication detail setting of the drawing software.
For setting items other than described in this section, refer to the following manual.
GT Designer3 Version1 Screen Design Manual (Fundamentals)
 Communication detail setting of host (modem)
On the communication detail setting screen of host (modem), the communication setting between the GOT and the
modem and the modem operation can be executed.
Item
Description
Setting range
PC connection type
Select the connection method to the PC.
Host (PC) / Host (Modem)
<Default: Host (PC)>
Transmission Speed
Set the transmission speed when communicating.
9600/19200/38400/57600/115200
<Default: 115200>
Data Bit
Set the data bit when communicating.
7bit/8bit <Default: 8bit>
Stop Bit
Set the stop bit length when communicating.
1bit/2bit <Default: 1bit>
Parity
Set whether to execute or not the parity check during
communication. When executing, set the type of the parity check.
Odd/Even/None <Default: Odd>
Init. AT command
Set the AT command for initialize the modem.
<Default: AT & FE0%C0 & K0 & D0W2S0=1>
Modem operation
Touch the [Init.] button to initialize the modem.
Touch the [Cut] button to disconnect the line.
-
10 - 10
10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)
10.2 Communication Detail Setting
On the communication detail setting screen of MELSEC-FX, registration, deletion, cancellation, or protection of the
keyword for FX series PLC can be executed.
UTILITY FUNCTION
9
 Keyword settings of MELSEC-FX
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
Keyword is registered.
Touching the [Regist] key displays the Registration Selection screen.
For a FX PLC*1 that is not compatible with the customer keyword, the keyboard for the keyword input of
is
displayed.
Select [Keyword] or [Keyword and Customer keyword].
When the [Enter] key is touched, the selection is completed and the keyboard for the keyword input is displayed.
12
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
13
Selection
Description
When [Keyword] is selected
Only keyword can be registered.
When [Keyword and Customer keyword] is selected
The Customer Keyword can be registered after registration of the keyword.
For details on FX PLC compatible with customer keyword, refer to the manual of the PLC used.
POINT
15
The customer keyword allows the user to clear the protection set by a keyword. However, the protection cannot be
deleted.
CLEANING DISPLAY
SECTION (CLEAN)
*1:
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
1.
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
(1) Regist
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
11
10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)
10.2 Communication Detail Setting
10 - 11
2.
When the registration is selected or the Regist key is touched on a PLC not compatible with the customer keyword,
the keyboard for the keyword input is displayed in a pop-up window.
When the keyword is input and the [Enter] key is touched, registration is completed.
When [Keyword and Customer Keyword] is selected on the selection screen for the registration, the Customer
Keyword entry screen of
is displayed.
For the keyword, 8 digits from 0 to 9 or A to F must be set.
Setting
Target PLC
FX PLC compatible with 2nd keyword*1
FX PLC not compatible with 2nd keyword*1
*1
*2
3.
10 - 12
When keyword and 2nd keyword are
registered
[Registration conclition]*2 can be selected.
-
When only keyword is registered
[Registration conclition]*2 cannot be selected.
For details on FX PLC compatible with 2nd keyword, refer to the manual of the PLC used.
[Registration conclition]
Options can be selected among [Read/Write Protect], [Write Protect], or [All Protect].
For access restrictions of each setting, refer to the manual of the PLC used.
When [Keyword and Customer Keyword] is selected on the selection screen for registration and the keyword input
is completed, the Customer Keyword registration screen is the displayed.
When the customer keyword is input and the [Enter] key is touched, registration is completed.
To set the customer keyword, 8 digits from 0 to 9 or A to F must be used.
10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)
10.2 Communication Detail Setting
POINT
(1) Selection of keyword protection level
For the devices which can perform the online operation of FX PLC, 3 levels of protection can be set.
When the monitoring or setting change by online devices is needed, set the keyword taking the following into
consideration.
Set the keyword starting with one of A, D to F, or 0 to 9.
Set the keyword starting with B.
Set the keyword starting with C.
(b) When keyword and 2nd keyword are registered
Protection level is selected by [Registration conclition].
(2) Applicability of monitoring for each keyword protection level
The applicability of monitoring for each protection level is as follows.
Item
All operation
prohibition
Read/
Incorrect
write
protection
Erroneous
write
prohibition
When keyword and 2nd keyword are
registered
All Protect
Read/Write
prohibition
Write
Protect
Keyword
unregistered/
protection
cancelled
Device monitoring
Device
change
*1
T, C setting values
and file register
(from D1000)
*1
*1
12
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
When only keyword is registered
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
11
*1
Other than the
above
13
When the T, C setting values are specified indirectly, changing devices is available.
(3) Difference between [All Protect] and [All operation prohibition]
When [All Protect] is selected, both device display and input by the programming tool or GOT are prohibited.
When [All operation prohibition] is selected, device display and input are possible although operations by the
programming tool are all prohibited.
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
All operation prohibition:
Read/incorrect write protection:
Erroneous write prohibition:
10
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
(a) When only keyword is registered
Protection level is selected by the head character of keyword.
UTILITY FUNCTION
9
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)
10.2 Communication Detail Setting
10 - 13
(2) Delete
Registered keyword is deleted.
1.Touching the [Delete] key pops up a keyboard for keyword input.
2.When the correct keyword is input and the [Enter] key is touched, the keyword is deleted.
Target PLC
Setting
FX PLC compatible with 2nd keyword
Input a keyword to be deleted.
FX PLC not compatible with 2nd
keyword
Input a keyword to be deleted only into "keyword".
"2nd keyword" is ignored.
(3) Clear
To access an FX PLC where a keyword has been registered, keyword protection is cancelled.
1.
2.
Touching the [Clear] key pops up a keyboard for keyword input.
When the correct keyword is input and the [Enter] key is touched, the protection is cancelled.
Target PLC
Setting
FX PLC compatible with 2nd keyword
Input a keyword or Customer Keyword to cancel the protection.
FX PLC not compatible with 2nd
keyword
Input a keyword only into "keyword" to cancel the protection.
"2nd keyword" is ignored.
(4) Protect
A keyword with cancelled protection is reactivated for protection.
1.Touching the[Protect] key activates keyword protection.
10 - 14
10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)
10.2 Communication Detail Setting
9
10.3.1
UTILITY FUNCTION
10.3 Ethernet Setting
Ethernet setting functions
The contents of the Ethernet setting in drawing software can be checked.
The setting of the host station can be changed.
For Ethernet setting, refer to the following.
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
GOT1000 Series Connection Manual for GT Works3
Display operation of Ethernet setting
Main menu
9.3 Utility Display)
11
Communication setting
Touch
[Ethernet.setting]
12
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
Touch
[Comm.setting]
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
(
Ethernet setting
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
13
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
10.3.2
10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)
10.3 Ethernet Setting
10 - 15
10.3.3
Display contents of Ethernet setting
The following describes the setting items and the display contents of the Ethernet setting.
(1) Channel selection tab
Channels can be switched.
Switching to the channel which does not have the Ethernet setting is not available.
[*] is displayed on the tab of the channel whose setting is changed.
(2) Ethernet setting item
The contents of the Ethernet setting configured in drawing software are displayed.
The setting of the host station can be changed.
■ Change of host
(3) Restore default settings
Touching this button cancels the change of the setting and returns the setting to the status when the project data
was written.
POINT
(1) How to cancel the change of the setting in the [Ethernet setting] screen
Cancel the settings changed in the [Ethernet setting] screen with the [Restore default settings] button.
The changed settings remain until they are canceled with the [Restore default settings] button.
The changed settings are not canceled even if writing the project data or OS to the GOT.
When the project data is written to the GOT without canceling the changed settings, those changed settings
are reflected to the Ethernet setting of the written project data.
(If the written project data does not have a channel with same Ethernet settings as that of the channel
changed in [Ethernet setting] screen, the changed settings are not reflected.)
(2) Range where the settings changed in the [Ethernet setting] screen are reflected
The settings changed in the [Ethernet setting] screen are valid in the GOT. On the other hand, they are not
overwritten to the project data written to the GOT.
The changed settings are not reflected to the project data which is read from the GOT after changing the
settings.
If the GOT data is copied with the GOT data package acquisition, the change in the [Ethernet setting] screen
is reflected to the copied data.
10 - 16
10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)
10.3 Ethernet Setting
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
CLEANING DISPLAY
SECTION (CLEAN)
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
1.
2.
3.
10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)
10.3 Ethernet Setting
UTILITY FUNCTION
Touch the device to be set as the host.
Touch the [OK] button.
Touching the [ ] button restarts the GOT and the
GOT operates with the changed settings.
10 - 17
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
 Change of host
9
10
11
12
13
14
15
16
10 - 18
10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)
10.3 Ethernet Setting
11. DISPLAY AND OPERATION
SETTINGS (GOT SET UP)
UTILITY FUNCTION
9
Display
11-1
Adjusting brightness and contrast
11-5
Buzzer volume, window move buzzer volume, key sensitivity, key reaction speed, touch detection mode
11-6
Security setting
11-9
Utility call key
11-11
Touch panel calibration
11-13
USB mouse/keyboard setting
11-15
VNC®
11-17
server function setting
10
11
Ch No.
11-18
Setting the storage locations for backup data and backup settings, and setting the maximum number of backup
data
11-19
Setting the CPU No. setting at backup to "YES" or "NO"
11-20
Trigger backup settings
11-21
Behavior of duplicate IPs
Setting the GOT operation when a device with the same IP address as that of the GOT is added to the network
afterwards.
11-22
12
License management
license registration/deregistration
11-25
11.1 Display Setting
11.1.1
Function of Display
13
Setting regarding display is possible.
The items which can be set are shown below. When each item part is touched, the respective setting becomes possible.
Item
Description
Setting range
(Japanese)
(English)
Confirmation of the current language and switching language
can be performed regarding with the language displayed by
utility and dialog box.
Language*1
(Chinese (Simplified))
(Chinese (Traditional))
(Korean)
(German)
(At factory shipment: User's selection)
The title display period at the main unit boot can be set.
0 to 60 seconds*2
(At factory shipment: 5 seconds)
Screen save time
The period from the user stops the touch panel operation till
the screen save function starts can be set.
0 to 60 minutes
(At factory shipment: 5 seconds)
Screen save backlight
Whether turning ON or OFF the backlight simultaneously at
the start of the screen save function can be specified.
ON/OFF
(At factory shipment: OFF)
Battery alarm display
Whether to display system alarm when the voltage of the GOT
internal battery has dropped can be specified.
ON/OFF
(At factory shipment: OFF)
15
The brightness can be adjusted.
Invert colors
(only GT1450-Q)
■ Brightness, contrast
For the user-created screen and the utility screen, whether to
invert the displayed colors can be specified.
*1
ON/OFF
(At factory shipment: OFF)
16
Only selectable languages are displayed.
The selectable languages differ depending on the fonts installed in the GOT.
For details of the fonts, refer to the following manual.
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
Brightness, contrast
GT Designer3 Version1 Screen Design Manual (Fundamentals)
*2
Setting 0 does not hide the title screen.
The title screen is always displayed for 4 seconds or longer (which changes depending on the project data contents).
11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)
11.1 Display Setting
14
CLEANING DISPLAY
SECTION (CLEAN)
Opening screen time
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
Backup/restoration
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
Transparent mode
Reference
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
Operation
Description
Language, opening screen time, screen save time, screen save backlight, battery alarm display and invert colors
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
Item
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
Setting screen for display and setting screen for operation can be displayed from the utility screen.
In the setting screen for display and the setting screen for operation, the following settings can be set.
11 - 1
POINT
(1) Display setting by GT Designer3
Select [Common Settings]
[GOT Environment Settings]
[GOT Setup] from GT Designer3 to make the
settings of opening screen time, screen save time and screen save backlight.
To change a part of the setting after downloading the project data, change the setting at the display setting of
GOT.
GT Designer3 Version1 Screen Design Manual (Fundamentals)
(2) Screen save time
Using the system information function can compulsorily switch the controller to the screen saving status
(Forced Screen Saver Disable Signal) or disable the screen save time (Automatic Screen Saver Disable
Signal) set with Utility.
GT Designer3 Version1 Screen Design Manual (Fundamentals)
(3) Screen save backlight
When [Screen save backlight] is set to [ON], using the system information function (Backlight OFF output
signal) can switch the backlight OFF from the controller.
When [Screen save backlight] is set to [OFF], the above signal has no effect on the screen save backlight.
GT Designer3 Version1 Screen Design Manual (Fundamentals)
11.1.2
Display operation of Display
Main menu
(
GOT setup
9.3 Utility Display)
Touch
[Display]
Touch
[GOT setup]
Display
Touch an item to
change settings
11 - 2
11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)
11.1 Display Setting
9
Display operations
 Language
1.
UTILITY FUNCTION
11.1.3
Touching the setting items displays the Select
Language screen.
Touching [OK] button defines the setting contents.
11
12
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
3.
Touching the button of a desired language selects
the language and returns the screen to the Display
screen.
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
2.
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
4.
Closing the display setting and GOT setup screens
after completing the setting of all items to change
with [ ] button restarts the GOT and reflects the
setting contents.
HINT
14
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
Touching [ ] button without touching [OK] button
displays the dialogue box shown on the left.
[OK] button: The changed value is canceled, and
the screen is closed.
[Cancel] button:The display setting screen is
displayed.
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
13
The system message switch button is displayed only for the selectable languages.
The selectable languages differ depending on the fonts installed in the GOT.
For the relation between the selectable languages and the fonts, refer to the following.
GT Designer3 Version1 Screen Design Manual (Fundamental) 2.5 Specifications of Applicable
Characters
The system language can be switched using the system language switching device set with GT Designer3.
For the setting method of the system language switching device, refer to the following.
GT Designer3 Version1 Screen Design Manual (Fundamentals)
4.3 Language Switching Device Setting (GOT Environmental Setting: Language Switching)
11 - 3
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
(2) System language switching using the device
11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)
11.1 Display Setting
CLEANING DISPLAY
SECTION (CLEAN)
15
(1) Selectable languages
 Opening screen, screen save time
1.
2.
Touching the setting time (numerical) displays the
keyboard.
Input numeric with the keyboard.
Touching [OK] button defines the setting contents.
Touching [ ] button without touching [OK] button
displays the dialogue box shown on the left.
[OK] button: The changed value is canceled, and
the screen is closed.
[Cancel] button:The display setting screen is
displayed.
3.
Closing the display setting and GOT setup screens
after completing the setting of all items to change
with [ ] button restarts the GOT and reflects the
setting contents.
 Screen save backlight, battery alarm display, invert colors
1. Touching the setting item changes the setting items.
(ON
2.
OFF)
Touching [OK] button defines the setting contents.
Touching [ ] button without touching [OK] button
displays the dialogue box shown on the left.
[OK] button: The changed value is canceled, and
the screen is closed.
[Cancel] button:The display setting screen is
displayed.
3.
11 - 4
Closing the display setting and GOT setup screens
after completing the setting of all items to change
with [ ] button restarts the GOT and reflects the
setting contents.
11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)
11.1 Display Setting
9
1.
Touching the setting items displays the brightness
contrast adjustment screen.
UTILITY FUNCTION
 Brightness, contrast
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
2.
3.
4.
Brightness can be adjusted by touching [+], [-] key
of brightness adjustment.
Contrast can be adjusted by touching [+], [-] key of
contrast adjustment.
Touching [OK] button defines the setting contents.
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
(For monochrome screen)
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
Touching [ ] button without touching [OK] button
displays the dialogue box shown on the left.
[OK] button: The changed value is canceled, and
the screen is closed.
[Cancel] button: The brightness/contrast
adjustment screen is displayed.
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)
11.1 Display Setting
11 - 5
11.2 Operation Setting (Settings Regarding Operation)
11.2.1
Operation setting functions
Setting regarding GOT operation can be set.
The items which can be set are described below. Touching the each item part makes the respective setting become
possible.
Function
Description
Setting range
Buzzer volume setting
Buzzer volume setting can be changed.
OFF/SHORT/LONG
(At factory shipment: SHORT)
Window move buzzer volume setting
Whether turn ON/OFF buzzer when move window can be selected.
ON/OFF
(At factory shipment: ON)
Security level change screen can be displayed.
Security setting screen change
-
11.2.4 Security level change
Utility call key setting screen can be displayed.
Utility call key screen change
-
11.2.5 Utility Call Key Setting
The sensitivity of touch panel when GOT screen is touched can be set.
E.g. a setting can be changed when double-touch is made when touching
the GOT screen only once. (For preventing chattering)
Key sensitivity setting
1 to 8*1
Touch panel reading error can be corrected.
Touch panel calibration
11.2.6 Adjusting the touch panel position (Touch panel calibration)
-
Set the setting items related with USB mouse/keyboard.
USB mouse/keyboard setting
VNC® server function setting
*1
-
11.2.7 USB mouse/keyboard setting
The authorization guarantee time for the VNC® server function can be set.
0 to 3600 seconds
<At factory shipment: 0 seconds>
Relation between the [Key sensitivity] setting and [Key reaction speed]
The larger the set value in [Key sensitivity] is, the shorter the time taken from touching the touch panel until the GOT responds
becomes.
E.g. decrease the value set for [Key sensitivity] when double-touch is made when touching the GOT screen only once. (Decrease
the reaction speed.)
The relation between the [Key sensitivity] setting and [Key reaction speed] is as follows.
[Key sensitivity] setting
[Key reaction speed]
Quick response
Slow response
8
7
-20ms
-10ms
6
0ms
(Standard)
5
4
3
2
1
+10ms
+20ms
+40ms
+80ms
+120ms
POINT
Operation setting by GT Designer3
Select [Common Settings]
[GOT Environment Settings] [GOT Setup] from GT Designer3 to make the settings
of buzzer sound and buzzer sound at window move.
To change a part of the setting after downloading the project data, change the setting at the display setting of GOT.
GT Designer3 Version1 Screen Design Manual (Fundamentals)
11 - 6
11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)
11.2 Operation Setting (Settings Regarding Operation)
CLEANING DISPLAY
SECTION (CLEAN)
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
Touch
[GOT setup]
Touch
[Operation]
Operation
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
Main menu
Touch an item to
change settings
11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)
11.2 Operation Setting (Settings Regarding Operation)
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
(
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
GOT setup
9.3 Utility Display)
UTILITY FUNCTION
11.2.2
Display operation of Operation
9
10
11
12
13
14
15
16
11 - 7
11.2.3
Setting operation of operation
 Buzzer volume, window move buzzer volume
1.
2.
Touching the setting item changes the setting items.
Touching [OK] button defines the setting contents.
Touching [ ] button restarts the GOT and reflects
the setting contents.
 Security setting
For the security setting operation, refer to the following.
11.2.4 Security level change
 Utility call key
For the utility call key operation, refer to the following.
11.2.5 Utility Call Key Setting
 Key sensitivity setting
1.
2.
3.
*1
Touching the setting items displays the keyboard.
Enter the numerical value from the keyboard.
The key response speed*1 corresponding to the
[Key sensitivity] setting is displayed.
Touching [OK] button defines the setting contents.
Touching [ ] button restarts the GOT and reflects
the setting contents.
Relation between the [Key sensitivity] setting and [Key reaction speed]
The larger the set value in [Key sensitivity] is, the shorter the time taken from touching the touch panel until the GOT responds
becomes. E.g. decrease the value set for [Key sensitivity] when double-touch is made when touching the GOT screen only once.
(Decrease the reaction speed.)
The relation between the [Key sensitivity] setting and [Key reaction speed] is as follows.
[Key sensitivity] setting
[Key reaction speed]
Quick response
8
7
-20ms
-10ms
Slow response
6
0ms
(Standard)
5
4
3
2
1
+10ms
+20ms
+40ms
+80ms
+120ms
 Touch panel calibration
For touch panel calibration operation, refer to the following.
11.2.6 Adjusting the touch panel position (Touch panel calibration)
 USB mouse/keyboard setting
For the USB mouse/keyboard setting, refer to the following.
11.2.7 USB mouse/keyboard setting
 VNC® server function setting
Refer to the following for the VNC® server function setting operation
11.2.8 VNC(R) server function setting
11 - 8
11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)
11.2 Operation Setting (Settings Regarding Operation)
9
Security level change
 Security level change functions
Changes the security level to the same security level set by each object or screen switch.
To change the security level, input the password of the security level which is set in GT Designer3.
GT Designer3 Version1 Screen Design Manual (Fundamentals)
Security level setting, Password setting................
10
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
POINT
Restrictions on screen display
The security level change screen cannot be displayed when project data do not exist in GOT.
Change the security level after downloading the project data to GOT.
11
Main menu
GOT setup
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
 Display operation of Security level change
Operation
9.3 Utility Display)
12
Security setting
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
Touch
[Security setting]
13
Security level change
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
Touch
[GOT setup]
Touch
[Operation]
Touch
[Security level change]
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
Input the password of
the security level which
is set in Drawing software
CLEANING DISPLAY
SECTION (CLEAN)
15
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
(
UTILITY FUNCTION
11.2.4
11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)
11.2 Operation Setting (Settings Regarding Operation)
11 - 9
 Security level change operation
(1) Password input operation
1.
2.
3.
4.
5.
By touching [0] to [9] , [A] to [F] key, the password of
the changed security level is input.
When correcting the input character, touch [Del] key
to delete the correcting character and input the
password again.
After inputting password, touch the [Enter] key.
When the password matches, a message notifying
successful change of the security level is displayed.
When the password does not match, an error
message is displayed.
Touching [OK] button returns the screen to the
password input screen again.
Touching [ ] button returns the screen to the
security setting screen.
POINT
About forgetting to return to the original level after changing security level temporarily
When use GOT after temporarily changing the security level, do not forget to return the security level to the original
level.
11 - 10
11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)
11.2 Operation Setting (Settings Regarding Operation)
9
UTILITY FUNCTION
Utility Call Key Setting
 Utility call key setting function
The key position for calling the main menu of the utility can be specified.
For the key position, 0 or 1 point can be specified from 4 corners on the screen.
By keeping pressing the screen, a setting to switch the screen to the utility is available.
This prevents a switching to the utility by an unintentional operation.
10
POINT
Operation setting by GT Designer3
Select [Common Settings]
[GOT Environment Settings]
[GOT Setup] from GT Designer3 to make the settings
of the utility call key.
To change a part of the setting after downloading the project data, change the setting at the display setting of GOT.
 Display operation of Utility call key
GOT setup
Operation
Touch
[GOT setup]
Touch
[Operation]
12
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
9.3 Utility Display)
Touch
[Utility call key]
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
13
Menu call key
14
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
Main menu
Touch buttons to set
for the utility call key
CLEANING DISPLAY
SECTION (CLEAN)
15
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
(
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
GT Designer3 Version1 Screen Design Manual (Fundamentals)
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
11.2.5
11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)
11.2 Operation Setting (Settings Regarding Operation)
11 - 11
 Setting operation of utility call key
1.
Touch ● or
displayed at the 4 corners of
the setting screen. The button repeats ●
with every touch. Set the corner to be set to a key
position to ● .
For the key position, 0 or 1 point only can be set.
2.
3.
4.
When setting 1 point, specify the time to switch to
the utility in case of keeping pressing the key
position.
Touch the time input area.
Touching the input area displays a keyboard.
Input numerical value from the keyboard.
Touching [OK] button defines the setting contents.
Touching [ ] button returns the screen to the
[Operation] screen.
POINT
(1) When the utility call key is set to the zero point
Even when the utility call key is set to the zero point, you can display the main menu using either of the
following two operations:
• Pressing the special function switch set on the user-created screen
• Keeping pressing the upper left corner while the [Booting.] message is displayed after powering up.
9.3.1 Display operation of main menu
(2) Precautions on using the advanced alarm popup display
When [Display Position Switching] is set to [Switch] in the advanced alarm popup display setting, set either of
the following for the utility call key.
• Setting the position of the utility call key to the upper-right or lower-left corner
• Setting [Pressing Time] of the utility call key to 1 or more seconds
When [Pressing Time] is set to 0 and the key position is set to the lower-left corner, the operation is as
described below. If the positions of the key and the advanced alarm popup display overlap, the utility screen
appears by switching the display position of the advanced alarm popup display.
For the advanced alarm popup display, refer to the following.
GT Designer3 Version1 Screen Design Manual (Functions)
(3) When limiting the display and operation of the utility
When limiting the display and operating users, set a password to the GOT using the GT Designer3. If a user
tries to display the main menu of the utility, the password input screen is displayed.
For details on setting passwords, refer to the following.
GT Designer3 Version1 Screen Design Manual (Fundamentals)
11 - 12
11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)
11.2 Operation Setting (Settings Regarding Operation)
9
Adjusting the touch panel position (Touch panel calibration)
 Touch panel calibration setting function
Before adjustment
Run
After adjustment
Stop
Run
10
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
Touch panel reading error can be corrected.
Normally the adjustment is not required, however, the difference between a touched position and the object position
may occur as the period of use elapses.
When any difference between a touched position and the object position occurs, correct the position with this
function.
UTILITY FUNCTION
11.2.6
Stop
The [Run] will operate though you
intended to touch the [Stop] button.
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
11
The [Stop] button can be touched
without fail.
 Display operation of Touch panel calibration
GOT setup
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
Main menu
Operation
9.3 Utility Display)
13
Touch
[Touch panel
calibration]
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
Touch
[Operation]
Touch panel calibration
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
15
CLEANING DISPLAY
SECTION (CLEAN)
Touch
[GOT setup]
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
(
12
11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)
11.2 Operation Setting (Settings Regarding Operation)
11 - 13
 Touch panel calibration operation
Touch the
point displayed on the screen with the finger one by one to make the setting.
1.
displayed on the upper
2.
Touch the
point displayed on the upper right.
3.
Touch the
point displayed on the lower left.
4.
Touch the
point displayed on the lower right.
5.
11 - 14
Touch the center of the
left precisely.
Touching the
button displayed on the upper
right returns the screen to the previous screen.
When the precise touch could not be made, touch
the [Readjustment] button to make the setting from
again.
11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)
11.2 Operation Setting (Settings Regarding Operation)
9
USB mouse/keyboard setting
UTILITY FUNCTION
11.2.7
 Function of USB mouse/keyboard
To install and use the USB mouse/keyboard on the GOT, set the USB mouse/keyboard.
 Display operation of USB mouse/keyboard
(
GOT setup
10
Operation
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
Main menu
9.3 Utility Display)
Touch
[Operation]
Touch
[GOT setup]
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
Touch
[USB mouse/keyboard]
USB mouse/keyboard
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
1.
To use the USB mouse, touch the setting item of
[Use USB mouse].
The setting content is changed by touching.
(YES
NO)
14
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
 USB mouse/keyboard setting operation
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
13
CLEANING DISPLAY
SECTION (CLEAN)
15
(Continued to next page)
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)
11.2 Operation Setting (Settings Regarding Operation)
11 - 15
2.
3.
4.
5.
11 - 16
To move the mouse cursor to the touched position,
touch the setting item of [Interlock with mouse
cursor touch operation].
The setting content is changed by touching.
(YES
NO)
To use the USB keyboard, touch the setting item of
[Use USB keyboard].
The setting content is changed by touching.
(YES
NO)
To use the USB keyboard, touch the setting item of
[USB keyboard type].
The setting content is changed by touching.
(Japanese 106 keyboard
English 101
keyboard)
Touching [OK] button defines the setting contents.
Touching [ ] button returns the screen to the
[Operation] screen.
11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)
11.2 Operation Setting (Settings Regarding Operation)
 VNC® server function setting
In the VNC® server function setting, the authorization guarantee time for the VNC® server function can be set.
For the details of the VNC® server function, refer to the following.
GT Designer3 Version1 Screen Design Manual (Functions)
Operating priority
guaranteed time
10
Description
Setting range
The time that the authorized equipment holds the authorization after you operate the authorized
equipment can be set.
(The unauthorized equipment cannot obtain the authorization until the set time elapses.)
0 to 3600 seconds
(At factory shipment: 0 seconds)
POINT
Authorization guarantee time cancel signal (GS1792.b8)
When the Authorization guarantee time cancel signal (GS1792.b8) turns on, the authorization guarantee time
setting is disabled.
 Displaying the VNC® server function setting
Main menu
GOT setup
Operation
Operation
9.3 Utility Display)
Touch
[GOT setup]
11
12
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
(
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
Function
UTILITY FUNCTION
9
VNC(R) server function setting
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
11.2.8
Touch
[Operation]
scroll lower.
Touch
[VNC server func. setting]
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
VNC server function setting
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
1.
2.
Touch the input field for [Operating priority
guaranteed time] to display a keyboard.
Input the authorization guarantee time with the
keyboard.
Touching [OK] button defines the setting contents.
Touching [ ] button returns the screen to the
operation setting screen.
11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)
11.2 Operation Setting (Settings Regarding Operation)
11 - 17
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
(1) Operating priority guaranteed time
CLEANING DISPLAY
SECTION (CLEAN)
15
 VNC® server function setting operation
11.3 Transparent Mode Setting
 Function of the transparent mode
When using the multi-channel function, the channel No. of a controller to which the FA transparent function is
executed can be specified. For the multi-channel function and FA transparent function, refer to the following manual.
GOT1000 Series Connection Manual (Mitsubishi Products) for GT Works3
Function
Description
Ch No.
Setting range
The channel No. of a controller to which the FA transparent function is executed can be set.
1/2
(Default: 1)
 Display operation of Transparent mode
Main menu
(
GOT setup
9.3 Utility Display)
Touch
[GOT setup]
Touch
[Transparent mode]
Transparent mode
 Setting operation of transparent mode
1.
2.
11 - 18
Touching the transparent Ch No. (numerical part)
on the left displays the screen to select the
communication driver.
Select the channel to execute the FA transparent
function.
Touching [OK] button defines the setting contents.
Touching [ ] button returns the screen to the [GOT
Setup] screen.
11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)
11.3 Transparent Mode Setting
9
UTILITY FUNCTION
11.4 Backup/Restoration Setting
The storage location for backup data can be set.
For how to use the backup/restoration, refer to the following manual.
GOT1000 Series Extended/Option Functions Manual for GT Works3
10
Description
Setting range
The drive for storing backup settings, including parameters and passwords
for controllers, can be selected.
Drive for backup data
The drive for storing backup data can be selected.
A: Built-in SD Card
E: USB memory
(Default: A: Built-in SD Card)
Trigger backup setting
The GOT automatically backs up data when triggers (Rise, Time) specified
for each backup setting are met.
None/Rise/Time
(Default: None)
Max. of backup data
Set the maximum number of backup data to be stored.
(When 0 is specified, the GOT does not check the number of backup data to
be stored.)
Setting range: 0 to 50
(Default: 10)
Enable CPU No. setting
Set the CPU No. setting at backup to "YES" or "NO".
YES/NO
(Default: NO)
11
12
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
Drive for backup setting
A: Built-in SD Card
E: USB memory
(Default: A: Built-in SD Card)
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
Item
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
Set the following items with touching the items on the GOT.
 Display operation of Backup/restoration setting
Main menu
GOT setup
13
Touch
[Backup/restoration setting]
14
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
Backup/restoration setting
15
CLEANING DISPLAY
SECTION (CLEAN)
Touch
[GOT setup]
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
9.3 Utility Display)
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
(
11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)
11.4 Backup/Restoration Setting
11 - 19
 Setting operation of backup/restoration setting
(1) Drive for backup setting, drive for backup data
1.
2.
Touching the setting item changes the setting items.
Touching [OK] button defines the setting contents.
Touching [ ] button returns the screen to the [GOT
Setup] screen.
(2) Trigger backup settings
For operations of the trigger backup setting, refer to the following.
■ Trigger backup settings
(3) Max. of backup data
1.
Touching the setting items displays the keyboard.
Input numerical value from the keyboard.
Setting range: 0 to 50, Default: 10
(When 0 is specified, the GOT does not check the
number of backup data to be stored.)
2.
Touching [OK] button defines the setting contents.
Touching [ ] button returns the screen to the [GOT
Setup] screen.
(4) Enable CPU No. setting
1.
2.
11 - 20
Touching the setting item changes the setting items.
Touching [OK] button defines the setting contents.
Touching [ ] button returns the screen to the [GOT
Setup] screen.
11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)
11.4 Backup/Restoration Setting
When the conditions of the trigger specified for each backup setting (Rise, Time) are met, the GOT automatically backs
up data.
How to use the trigger backup, refer to the following manual.
GOT1000 Series Extended/Option Functions Manual for GT Works3
 Display operation of Trigger backup setting
3.
:
The GOT does not execute the trigger backup.
Rise
:
The GOT backs up data when the trigger
device turns on.
Time
:
The GOT backs up data at the specified time.
Touching a setting item for [Check changes (file
register)] changes the setting.
:
The GOT backs up data regardless that the
backup data are changed or not.
:
When the backup is executed, the GOT checks
if the backup data or file registers are changed
after the previous backup. When the data or file
registers are changed, the GOT backs up the
changed data or file registers.
:
When the backup is executed, the GOT checks
if the backup data are changed after the
previous backup. When the data are changed,
the GOT backs up the changed data.
The GOT does not check if the file registers are
changed or not.
When the trigger type is changed, the setting is
defined by touching the [OK] button.
Touching [ ] button returns the screen to the backup/
restoration setting screen.
When the trigger type is set to [Time], touching a
setting item for [Detail] switches the screen to the
trigger time setting screen.
In the screen, specify the days and time that the
GOT executes the backup.
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
None
12
13
14
Day
:
Select days that the GOT executes the backup
by touching displayed items.
Multiple days can be selected.
Time
:
Set the time that the GOT executes the backup
by touching the displayed item.
15
CLEANING DISPLAY
SECTION (CLEAN)
4.
Time)
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
2.
Rise
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
(None
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
Touching a setting item for the trigger type changes
the setting.
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
1.
UTILITY FUNCTION
9
 Trigger backup settings
POINT
Precautions for setting
16
11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)
11.4 Backup/Restoration Setting
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
When the trigger type is set to [Rise], set the trigger device with GT Designer3 in advance.
Failure to do so disables the backup setting with [Rise] set.
11 - 21
11.5 Behavior of Duplicate IPs
 Setting function for Behavior of duplicate IPs
The GOT operation can be set when a device with the same IP address as that of the GOT is added to the network
afterwards.
Function
Description
Setting range
Behavior of duplicate IPs
The GOT operation can be set when a device with the same IP address as that of
the GOT is added to the network afterwards.
Maintain a network connection(rec)
/Do not maintain a network connection
(Default: Maintain a network
connection (rec))
POINT
(1) When the IP address duplication is not checked
When the IP address of the GOT is set to 192.168.0.18, the IP address duplication check is not performed.
Depending on the device to connect with the GOT, the IP address duplication check may not be performed.
(2) When the GOT is added to the network in which a device with the same IP address as that of the GOT exists
The GOT goes into offline status and displays the following dialog box.
• When changing the IP address of another device which has the same IP address as that of the GOT
After changing the IP address of another device which has the same address as that of the GOT, touch the
[Reboot GOT] button to restart the GOT.
• When changing the IP address of the GOT
Touch the [Clear IP Address] button to clear the IP address of the GOT.
After touching the [Reboot GOT] button to restart the GOT, change the IP address of the GOT using the
Utility.
11 - 22
11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)
11.5 Behavior of Duplicate IPs
 Display operation of Behavior of duplicate IPs
UTILITY FUNCTION
Main Menu
GOT setup
9.3 Utility Display)
Touch
[GOT setup]
10
Touch
[Behavior of
duplicate IPs]
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
(
9
Behavior of duplicate IPs
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
11
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
2.
Touching the setting item changes the setting items.
• Maintain a network connection (rec):
The GOT stays connected to the network when a
device with the same IP address as that of the
GOT is added to the network afterwards.
A system alarm occurs.
• Do not maintain a network connection:
The GOT is disconnected from the network when
a device with the same IP address as that of the
GOT is added to the network afterwards.
Touching [OK] button defines the setting contents.
Touching [ ] button restarts the GOT and reflects
the setting contents.
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
1.
14
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
 Setting operation of Behavior of duplicate IPs
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)
11.5 Behavior of Duplicate IPs
11 - 23
POINT
(1) Precautions for selecting [Do not maintain a network connection]
When selecting [Do not maintain a network connection], the GOT is disconnected from the network at the
addition of a device with the same IP address as the GOT.
Therefore, there is a possibility that the running GOT cannot be communicated by IP address setting mistakes
or intended actions by malicious users, and the system control may be influenced by those errors.
Please change the setting of [Behavior of duplicate IPs] after carefully examining the necessity.
(2) Precautions for using a switching hub compatible with the spanning tree protocol
For the switching hub port connected with the GOT, configure the setting (PortFast or others) that makes the
GOT be ready for communications (forwarding state). The setting is required to make sure that the delay right
after the connection by the spanning tree protocol does not occur.
Without the setting, the Ethernet IP address duplication is not correctly detected.
Additionally, the GOT may not be connected to Ethernet correctly.
For the setting that makes the GOT be ready for communications (forwarding state), refer to the user’s
manual for the switching hub used.
11 - 24
11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)
11.5 Behavior of Duplicate IPs
9
UTILITY FUNCTION
11.6 License Management
For using functions which require a license, register the license for the GOT.
For releasing a registered license for the GOT, also execute on the license management screen.
Item
VNC®
server function
Description
Setting range
®
-
Registers/deletes the license of the VNC server function.
10
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
 License management function
Registers/deletes the license of the VNC® server function.
For the details of the VNC® server function, refer to the following.
GT Designer3 Version1 Screen Design Manual (Functions)
 Displaying the License management
GOT setup
9.3 Utility Display)
Touch
[GOT setup]
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
Touch
[License management]
License management
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
13
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
(
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
Main Menu
11
11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)
11.6 License Management
11 - 25
 Setting operation of License management
(1) When registering a license number for the GOT
1.
2.
3.
Touch the license number input area on the license
management screen, and then the keyboard
appears on the bottom of the screen.
Touch the [Regist] button to register the input
license number. If the [ ] button is touched without
touching the [Regist] button, the license number is
not registered.
After a license number is registered, touch the [ ]
button to close the license management screen.
(2) When releasing a license number for the GOT
1.
2.
Touch the [Cancel reg.] button to release the
registered license number.
Touch the [ ] button to close the license
management screen.
POINT
How to acquire a license number
For how to acquire a license number, please consult your local Mitsubishi (Electric System) Service center or
representative.
11 - 26
11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)
11.6 License Management
12. CLOCK SETTINGS AND BATTERY
STATUS DISPLAY
(TIME SETTING AND DISPLAY)
UTILITY FUNCTION
9
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
Setting items for clock display can be displayed from the GOT utility screen.
12.1 Time Setting and Display
11
Time setting and display functions
Setup the method to adjust the time between GOT clock data and clock data of PLC CPU connected with GOT.
12-2
Clock display
Carry out the display and setup of GOT clock data.
12-3
GOT internal battery
voltage status
Displays GOT internal battery voltage status.
12-3
12
Function
Description
Reference
POINT
Changing times
When the time is changed on the Time setting & display screen, the changed time is written in a programmable
controller even though [Adjust] or [Broadcast] is set for [Time setting].
As a result, the time of the programmable controller can be changed on the GOT even though [Adjust] is set for
[Time setting].
(The clock data of the controller set as [Adjust CH No.] of [Time setting] in [GOT Setup] ([Clock Setting]) from [GOT
Environment Settings]of GT Designer3 is changed.)
For details of [Adjust] and [Broadcast], refer to the following manual.
GT Designer3 Version1 Screen Design Manual (Fundamentals)
14
Time setting & display
9.3 Utility Display)
CLEANING DISPLAY
SECTION (CLEAN)
15
Touch
[Time setting & display]
Set the Time setting
and Clock setting
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
(
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
 Display operation of time setting
Main menu
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
Time settings and displaying of the status of GOT built-in battery are possible.
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
Clock setting
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
12.1.1
12. CLOCK SETTINGS AND BATTERY STATUS DISPLAY (TIME SETTING AND DISPLAY)
12.1 Time Setting and Display
12 - 1
 Operation of time setting
(1) Clock setting
Setup the method to adjust the time between GOT clock data and the clock data of controller connected to the
GOT.
It is same as set in the GOT setup in Environmental Setting of GT Designer3.
GT Designer3 Version1 Screen Design Manual (Fundamentals)
Setting
Description
Adjust the time of GOT clock data to the clock data of controller.
Adjust
Adjust the time of controller clock data to the GOT clock data.
Broadcast
Adjust the GOT and controllers to the controller whose clock data is used as a base.
Adjust/Broadcast
None
No adjustment of clock data.
1.
Touching the setup item changes the setup
contents.
Adjust
2.
Broadcast
Adjust/Broadcast
None
Touching [OK] button reflects the setup contents.
Touching the [ ] button restarts the GOT.
After restarting, the GOT operates with the changed
setting.
POINT
(1) When connecting with an external device which does not have clock function.
If set to [Adjust] or [Broadcast] for [Clock setting] while the GOT is connected with external devices (PLC or
microcomputers) which do not have clock function, the clock data will not be adjusted.
For the list of PLC installed with clock function, refer to the following.
GOT1000 Series Connection Manual for GT Works3
(2) Setting of clock setting and battery
When selecting [Broadcast] or [None] in clock setting, set the clock of the GOT once with connecting a battery
to the GOT.
(3) Operation setting by GT Designer3
Carry out the setting of clock setting in [GOT set up] in [Environmental Setting] of GT Designer3.
To change a part of the setting after downloading the project data, change the setting at the display setting of
GOT.
GT Designer3 Version1 Screen Design Manual (Fundamentals)
12 - 2
12. CLOCK SETTINGS AND BATTERY STATUS DISPLAY (TIME SETTING AND DISPLAY)
12.1 Time Setting and Display
to
Description
9
/
Del
Enter
Input numeric value in cursor position.
Move the cursor.
Move the cursor to the left by one character when [Del] Key is touched while inputting year, month, day, time, minutes, seconds.
Carry out nothing when touched other than when inputting the above.
Close the keyboard after the input time is displayed in clock display.
The update of the clock display does not restart even if the keyboard is closed.
The update of the clock display restarts with the operation of
Cancel
.
Cancel the input time and returns the time of clock display to the time at which the keyboard was displayed and close the
keyboard.
The update of the clock display does not restart even if the keyboard is closed.
The update of the clock display restarts with the operation of
3.
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
0
10
.
Touching the [OK] button reflects the settings and
restarts updating the clock display.
Then, the settings are reflected to both clock data
on the GOT and controller.
Touching [ ] button restarts the GOT if the clock
settings is changed, or closes the screen if clock
settings is not changed.
(3) GOT internal battery voltage status
Displays battery voltage status.
Status
Normal
Normal
Low/None
Low voltage
13
14
15
CLEANING DISPLAY
SECTION (CLEAN)
Display
12
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
Key
Input time with the keyboard by referring to the
table below.
Input the scheduled time when the operation of
is to be carried out since the input time is reflected
at the time of the operation of
.
The day of the week is displayed automatically
according to the input date.
The effective range of clock setting is as follows.
Jan. 1, 2000 to Dec. 31, 2037
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
2.
Touching the clock display section displays the
keyboard for input and stops the clock update.
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
1.
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
Carry out the display and setting of GOT clock data.
The setup methods of clock data are shown below.
UTILITY FUNCTION
9
(2) Clock display
When the battery voltage is low, replace the battery immediately.
For battery replacement procedure, refer to the following.
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
8.3.3 Battery replacement procedure
12. CLOCK SETTINGS AND BATTERY STATUS DISPLAY (TIME SETTING AND DISPLAY)
12.1 Time Setting and Display
12 - 3
12 - 4
12. CLOCK SETTINGS AND BATTERY STATUS DISPLAY (TIME SETTING AND DISPLAY)
12.1 Time Setting and Display
13. FILE DISPLAY AND COPY
(PROGRAM/DATA CONTROL)
UTILITY FUNCTION
9
13.1 Data Storage Location
Data type and storage location
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
 System
The data storage location and transferring (write/read) route for each data type are shown below.
Also, the data storage locations are shown below.
OS BootOS
Project data Write
12
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
C drive
(Built-in flash memory)
Read
PC
GT Designer3
Project data
Install/
Download
Upload
OS BootOS
Project data
Copy files on
Windows
Project data
A drive
(Built-in SD card)
E drive
(USB drive)
Write
BootOS
13
Project data
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
Project data
OS BootOS
Inserting/
Removing
USB memory
(when installed in GOT)
USB memory
SD card
(when installed in PC) (when installed in PC)
14
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
SD card
(when installed in GOT)
Install, Write :
Upload, Read :
The data of the Flash Memory (Project data, etc.) can be saved even if the battery voltage becomes low.
Item
Data type
BootOS
BootOS
Storage location
Built-in flash memory (C drive)
15
OS
Built-in SD card (A drive)
Built-in flash memory (C drive)
Communication driver
*1
CLEANING DISPLAY
SECTION (CLEAN)
Standard monitor OS
Extended function OS
*2
Option OS
*1
Project data
(Including recipe setting, alarm conditions, time action, and GOT setup.)
Project data
Built-in SD card (A drive)
Built-in flash memory (C drive)
*2
16
*1
The USB memory can be used from Utility.
*2
When using the project data stored in the built-in SD card (A drive) with the GOT, hold the SD card installed to the GOT. The USB
memory cannot be activated directly from the E drive. It can be used only for data storage.
16.3.2 Installing using the program/data control function (Utility)
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.1 Data Storage Location
13 - 1
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
13.1.1
10
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
The display of OS, project data or alarm data which is written in the GOT or SD card and the data transmission between
GOT and SD card/USB memory are possible.
The format of the SD card/USB memory is also possible.
 At maintenance
C drive
(Built-in flash memory)
Read
D drive
(Built-in SRAM)
Copy
Alarm
Hard copy
Copy
Alarm
Hard copy
A drive
(Standard CF card)
Alarm
Recipe
PC
GT Designer3
Logging
Hard copy
Copy files on
Windows
E drive
(USB drive)
Alarm
Hard copy
Recipe
Logging
SD card
(when installed in GOT)
USB memory
(when installed
in GOT)
Inserting/
Removing
USB memory
(when installed
SD card
in PC)
(when installed in PC)
Install, Write :
Upload, Read :
Item
Data type
Storage location
Alarm
Alarm data (Extended alarm log file and alarm log file)
Recipe
Recipe data (Advanced recipe file, Recipe file)
Built-in SD card (A drive)
Internal SRAM (D drive)
Logging
Logging (Logging file)
USB drive (E drive)*1
Hard copy
Image file (Hard copy function)
*1
The USB memory can be used from Utility.
POINT
Checking the available memory of storage location
When saving resource data, check available memory of storage location before use.
Memory capacity of internal SRAM (D drive) is 512kbytes. Use the built-in SD card (A drive) if the available
memory is not enough.
13 - 2
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.1 Data Storage Location
(2) When install Standard monitor OS, communication driver, Option OS
When Standard monitor OS, communication driver, or Option OS has already been installed, the version
information of the OS which has been installed and the dialog for selecting continue/not continue will be
displayed.
Moreover, when the different versions will coexist among all OSs (Standard monitor OS, communication driver,
and Option OS) by installing OS, the installation disapproving dialog will be displayed and the installation
process is canceled.
(3) When download project data
GOT automatically compares the version between the project data to be downloaded and the installed OS.
When the versions are different, the dialog confirming whether to install the OS together is displayed.
When downloading the project data from the SD card or USB memory, storing the project data and OS
beforehand is recommended.
The version of each OS installed in the GOT can be confirmed by [Property] of [OS information] screen.
10
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
When the BootOS to be installed has the older major version, GOT displays the installation disapproving
message to cancel the installation so that the older version may not be written.
(Even when the version of the BootOS to be installed has the same or later version, the version information and
the dialog for selecting continue/not continue will be displayed.)
Depending on the Installation method, the dialog box to be displayed varies.
• When installing from the built-in SD card, the dialog box is displayed by the main unit.
• When installing from GT Designer3 via USB or Ethernet, the dialog box is displayed by the GT Designer3
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
(1) When install BootOS
12
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
Confirm the OS version carefully when install BootOS and Standard monitor OS.
When OS is installed, GOT checks and compares the OS version automatically.
UTILITY FUNCTION
9
OS version confirmation
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
Explanation of OS version
01.00.00.A
BootOS version
(Appears only when the property
of the BootOS is displayed.)
Minor version
Major version
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
For details of the screen display operation, refer to the following.
13.2.1 OS information
Version confirmation of BootOS by rating plate
Check the version of BootOS installed in GOT at product shipment on the rating plate on GOT rear face.
When the Boot OS version is 2 digits,
only the lower digit is printed.
Example H/W version: H
Boot OS version: AD
AA
HD
BootOS
Version
BootOS
Version
Rating plate: HD
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.1 Data Storage Location
13 - 3
CLEANING DISPLAY
SECTION (CLEAN)
15
POINT
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
13.1.2
13.1.3
Capacity confirmation of the project data downloading location
When download the project data, confirm the capacity of the user area in the drive to which transferred, the transferred
project data size, the transfer size and buffering area size of the optional function OS in advance to judge whether to
carry out the download.
The capacities can be confirmed by GT Designer3. For details, refer to the following.
GT Designer3 Version1 Screen Design Manual (Fundamentals)
13.1.4
Display file
The display screen and storage destination for each type of data are shown below.
The file name and contents of each data can be displayed with property display of the utility
Item
Display screen
Storage destination (Drive name/folder name)
A drive/C drive/E drive
BootOS
: \G1BOOT\*2
Standard monitor OS system screen data
Standard monitor OS system screen
management information file
Standard monitor OS (monitor function)
6
Standard monitor OS
8-dot font (ASCII characters)
24-dot numerical HQ font
OS information screen
32-dot numerical HQ font
A drive/C drive/E drive*3
: \G1SYS\*2
TrueType numerical font
12-dot standard font
16-dot standard font
Extended function OS
Option OS
Communication driver
Project data*1
User-created screen data
Comment data
12-dot HQ fonts (Mincho/Gothic)
Project information
screen
A drive/C drive/E drive*3
:\PROJECT1\*2*4
16-dot HQ fonts (Mincho/Gothic)
TrueType (Mincho/Gothic)
Advanced alarm log file CSV file*5
Advanced alarm log file TXT file*5
Advanced alarm log file binary file*5
Alarm information screen
Alarm log file CSV file*5
Hard copy file BMP file*5
Resource data
Hard copy file JPG file*5
Hard copy information
screen
A drive/D drive/E drive *6
:\
With GT Designer3, any folder name or file name can
Advanced recipe
information screen
be specified.*2
Advanced recipe file CSV file*5
Advanced recipe file TXT file*5
Advanced recipe file binary file*5
Logging file CSV file*5
Logging file TXT file*5
Logging information
screen
Logging file binary file*5
*1
*2
*3
The user-created screen data, comment data, and font data are displayed as project data.
Each folder is created automatically when a file is installed, downloaded, or uploaded.
The USB memory cannot be activated directly from the E drive. It can be used only for data storage.
*4
The folder names and file names can be set at [System Settings] in [System Environment] of GT Designer3.
*5
*6
A serial number is automatically added to file names.
Each function does not provide direct storage to the E drive.
13.2.1 OS information
GT Designer3 Version1 Screen Design Manual (Fundamentals)
13 - 4
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.1 Data Storage Location
9
Each file name/folder name of BootOS and OS (Standard monitor OS, PC communication driver and Option OS) by
which each drive (A: Built-in SD card, C: Built-in flash memory, E: USB memory) holds can be displayed in lists.
Installation and uploading of the files are also possible.
Function
Description
Reference
Displaying file, folder data
The file/folder type, name, data size and creating date & time are displayed.
13-6, 13-7
Install
All OS files written in the A drive (Built-in SD card)/E drive (USB drive) can be installed in the C
drive (Built-in flash memory).
13-8
Upload
All OS files in the C drive (Built-in flash memory) can be uploaded to the A drive (Built-in SD card)/
E drive (USB drive).
13-9
Property display
Displays the property (file name, data size, type, version and creation date) of the file.
13-10
Data check
Data check of files is possible.
13-10
POINT
(1) Notes on installing OS
If the Boot OS or the Standard monitor OS is installed, such data on the GOT as the project data will be
deleted.
After installing the Boot OS or the Standard monitor OS, reinstall/download necessary data.
(2) Notes on handling OS files
When the OS boot drive is set to [A: Built-in SD card], installing and uploading OS files are not available.
12
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
Program/Data control
Main menu
11
13
 Display operation of OS information
9.3 Utility Display)
Touch
[OS information]
14
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
Touch
[Program/data control]
OS information
CLEANING DISPLAY
SECTION (CLEAN)
15
Select a drive and
operate BootOS
and OS files
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
(
10
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
 Function of OS information
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
OS information
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
13.2.1
UTILITY FUNCTION
13.2 Various Data Control
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 5
 Display example of OS information
OS information
OS information Storage file/folder display screen
(3)
(2)
(4)
(5)
(6)
(8)
(7)
(1)
Number
Item
Description
(1)
Select drive
The target drive which displays file or folder can be selected.
When the SD card is not installed, [A:Built-in SD card] is not displayed.
If the USB memory is not installed, [E: USB drive] is not displayed.
(2)
Kind
Indicates the type of the displayed name (file or folder).
In case of file, displays the extension; in case of folder, displays "DIR".
(3)
Name
The file name or folder name which is stored in the selected drive or folder is displayed.
When the file name or folder name exceeds 20 characters, the exceeding characters (the 21st
character or after) are not displayed.
(4)
Path name
Displays the path name of drive/folder which is currently displayed.
(5)
Size
Displays the size of the file displayed in [Name].
(6)
Date and time
The date and time when each file was created are displayed.
(7)
The size of drive
Displays the size in use and the entire size of the drive which is selected by drive selection.
(Only the size in use is displayed when selecting the C drive.)
(8)
Operation switch
Execution switch of each function.
(9)
Number of files
Displays the total number of the displayed files.
POINT
Folders and files displayed
For the folders and files displayed, refer to the following.
13.1.4 Display file
13 - 6
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
(9)
3.
4.
5.
6.
7.
Touching a folder name displays the information of
the touched folder.
Touching a folder name of [ . . ] displays the
information of the folder in one upper hierarchy.
Touching
button of the scrollbar scrolls up/
down the screen by one line.
Touching
button scrolls up/down the screen by
one screen.
Touching a file name selects and inverts the file.
For operation of installation, upload, property, data
check, refer to the following.
Install.................
This section (2)
Upload...............
This section (3)
Property.............
This section (4)
Data check.........
This section (5)
[Touching [
] button closes the screen.
10
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
2.
Touching a drive in [Select drive] displays the
information of the first folder of the touched drive.
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
1.
12
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
(1) Display operation of OS information
UTILITY FUNCTION
9
 OS information operation
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
13
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 7
(2) Installation operation
BootOS and OS which are written in the A drive (built-in SD card) or E drive (USB drive) can be installed in GOT.
(This item explains using the A drive.)
1.
Install the SD card to which the BootOS or OS to
install is written to the GOT.
For inserting/removing method of SD card/USB
memory, refer to the following.
8.1.2 Installing and removing procedures of
the SD card
8.2.2 Installing and removing procedures of
the USB memory
2.
Touch [A: Built-in SD card] of [Select drive].
3.
Touching [Install] button starts the install.
4.
13 - 8
When the installation is completed, the dialog shown
left is displayed.
Touching [OK] button restarts GOT.
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
(This item explains using the A drive.)
1.
Install the SD card used as the uploading destination
to GOT.
For inserting/removing method of SD card/USB
memory, refer to the following.
8.1.2 Installing and removing procedures of
the SD card
8.2.2 Installing and removing procedures of
the USB memory
2.
Touch [A: Built-in SD card] of [Select drive].
10
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
BootOS and OS in the C drive (Flash Memory) can be uploaded to the A drive (Built-in SD card) and E drive
(USB drive).
The SD card after uploading can be used for installing the OS on another GOT.
UTILITY FUNCTION
9
(3) Upload operation
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
13
Touching [Upload] starts the uploading.
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
3.
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
When the upload is completed, the dialog shown left
is displayed.
Touching [OK] button closes the dialog.
15
CLEANING DISPLAY
SECTION (CLEAN)
4.
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 9
(4) Property display operation
Displays the property of the file stored in the selected folder.
1.
Touching [Property] button after selecting the
property displaying target folder displays the
[Property] screen shown left.
In the [Property] screen, the following information is
displayed for each file selected by .
Item
2.
Name
Displays the file name.
Size
Displays the file size.
Kind
Displays the following items according to the
kind of the files.
Boot: BootOS
Basic: Standard monitor OS
Extend: Extend function OS
Option:Optional function OS
Comm.:Communication driver
Version
Displays the version of BootOS and OS.
Date, Time
Displays the date and time of the file creation.
Touching
button of the scrollbar scrolls up/
down the screen by one line.
Touching
by one screen.
3.
Description
button scrolls up/down the screen
Touching [ ] button returns the screen to the
previous screen display.
(5) Data check operation
Carries out data check of the selected system file.
When data is normal.
1.
2.
Touch [Data check] button after selecting a data
check target file. The dialog mentioned left will be
displayed after executing data check.
Touching [OK] button closes the dialog.
When data is erroneous.
13 - 10
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
The extended alarm log file or alarm log file held by each drive (A: Built-in SD card, C: Flash Memory, D: Internal
SRAM, E: USB drive) is displayed.
The functions below can be carried out for files.
The USB drive only stores log files, and cannot be displayed.
For details of Advanced Alarm, refer to the following manual.
GT Designer3 Version1 Screen Design Manual (Functions)
Function
Description
Reference
Displaying file, folder data
The file/folder name, data size and creating date & time are displayed.
13-12, 13-13
G1A
CSV conversion
Converts the G1A file of advanced alarm log file to CSV file.
13-14
G1A
TXT conversion
Converts the G1A file of advanced alarm log file to TXT file.
13-14
Delete
File is deleted.
13-15
Copy
File is copied.
13-16
 Display operation of Alarm information
Main menu
Program/data control
12
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
9.3 Utility Display)
Touch
[Alarm information]
Touch
[Program/data control]
11
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
13
Alarm information
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
Select a drive and operate
alarm log files
CLEANING DISPLAY
SECTION (CLEAN)
15
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
(
10
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
 Function of alarm information
UTILITY FUNCTION
9
Alarm information
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
13.2.2
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 11
 Display example of Alarm information
Alarm information screen
Alarm information: Storage file/folder display screen
(2)
(3)
(4)
(7)
(5)
(6)
(8)
(9)
(1)
Number
Item
Description
(1)
Select drive
The target drive which displays file or folder can be selected.
When SD card or USB memory is not installed, the following drives are not displayed.
• SD card: [A: Built-in SD card]
• USB memory: [E: USB drive]
(2)
Kind
Indicates the type of the displayed name (file or folder).
The file is indicated with an extension, while the folder is indicated with "DIR."
(3)
Name
Displays the file name or folder name.
For the long file/folder name, entire part may not be displayed.
Confirm the nondisplayed part with the [Copy] button, etc.
(
13.2.2 ■ Alarm information operation(4)Copy operation)
After confirmation, touch the [Cancel] button to cancel the operation.
(4)
Path name
Displays the path name of drive/folder which is currently displayed.
(5)
Size
Displays the size of the file displayed in [Name].
(6)
Date and time
The date and time when each file was created are displayed.
(7)
The size of drive
Displays the size in use and the entire size of the drive which is selected by drive selection.
(Only the size in use is displayed when selecting the C drive.)
(8)
Operation switch
Execution switch of each function.
(9)
Number of files
Displays the total number of the displayed files.
POINT
(1) Display of creation date and time
The creation date and time display is not updated even if a file is created or updated while displaying the
alarm information display screen.
If close the screen currently displayed (moving the screen to the folder of the upper hierarchy, etc.) and
display the screen again, the updated contents are displayed.
(2) Folders and files displayed
For the folders and files displayed, refer to the following.
13.1.4 Display file
13 - 12
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
3.
4.
Touching a folder name displays the information of
the touched folder.
Touching a folder of [ . . ] displays the information of
the folder of the one upper hierarchy.
Touching
button of the scrollbar scrolls up/
down the screen by one line.
Touching
one screen.
5.
6.
Alarm information: Storage file/folder display screen
7.
button scrolls up/down the screen by
Touching a file name selects the file.
For G1A
CSV, G1A
TXT, delete, copy, graph
operations, refer to the following.
G1A
CSV, G1A
TXT........
This section (2)
Delete.......................................
This section (3)
Copy.........................................
This section (4)
Touching [
] button closes the screen.
10
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
2.
Touching a drive of [Select drive] displays the
information of the touched drive.
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
1.
Alarm information screen
12
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
(1) Display operation of Alarm information
UTILITY FUNCTION
9
 Alarm information operation
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
13
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 13
(2) G1A
CSV conversion operation, G1A
TXT conversion operation
The selected G1A file is converted to CSV file or TXT file.
1.
(Example: When [G1A
CSV] button is touched)
2.
3.
4.
13 - 14
Touch and select the G1A file to convert into a CSV
file or a TXT file.
The following dialog box is displayed when touching
the following button according to the file type to
convert to.
• CVS file: [G1A
CSV] Button
• TXT file: [G1A
TXT] Button
Touch [OK] button.
When the file, whose name is the same, exists in the
destination folder, the dialog box shown at left
appears without starting the conversion.
Touching [OK] button overwrites the file.
Touching [Cancel] button cancels the conversion.
The message of completion is displayed in dialog
box when conversion is completed.
Touching [OK] button closes the dialog.
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
Deletes selected files.
Touch and select the file to delete.
Touching [Delete] button displays the dialog
mentioned left.
Touching [OK] button deletes the file.
Touching [Cancel] button cancels the deletion.
10
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
1.
2.
UTILITY FUNCTION
9
(3) Deletion operation
When the deletion is completed, the completion
dialog is displayed.
Touching [OK] button closes the dialog.
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
3.
11
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
13
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 15
(4) Copy operation
Copies the selected file.
Dialog for selecting a copy destination drive
1.
2.
3.
4.
5.
6.
13 - 16
Touch and select the file to copy.
Touching [Copy] button displays the message
[Please select a destination.] in the left bottom of the
screen.
If the copy destination folder is touched, the screen
display is changed to the folder of copy destination.
At this time, it cannot be copied into the same folder
where the file exists.
Select other folders.
Touching [Exec.] button displays the dialog box
shown left.
Touch [OK] button.
If there is a file of the same name in the copy
destination folder, the following dialog is displayed
without starting the copy.
When the copy is completed, the dialog of
completion is displayed.
Touching [OK] button closes the dialog.
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
9
Project Information
 Function of project information
The project data files stored in each drive (A: Built-in SD card, C: Flash Memory, E: USB memory) can be displayed
by lists.
In addition, the files can be downloaded, uploaded, deleted or copied, etc.
Description
Reference
The file/folder type, name, data size and creating date & time are displayed.
Delete
Deletes project data.
13-19
Copy
Copies project data. (can copy the A drive and E drive)
13-20
Property display
Displays the project data creation date, author name and the version of GT Designer3.
13-21
Data check
Data check of files is possible.
13-22
Download
Downloads the project data written in the A drive (Built-in SD card)/E drive (USB drive) to C drive
(Flash Memory).
13-22
11
Setup
The project data to be displayed can be selected.
13-24
Upload
Uploads the project data written in the C drive (Flash Memory) to the A drive (Built-in SD card)/E
drive (USB drive).
13-25
Setup cancel
Cancels the item which is selected for the project data to be displayed.
13-26
Notes on operating project data
When the OS boot drive is set to [A: Built-in SD card], deleting, copying, downloading, setting up, and uploading
project data are not available.
 Display operation of Project information
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
Main Menu
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
POINT
Program/Data control
9.3 Utility Display)
14
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
Touch
[Project information]
Touch
[Program/data control]
Project information
CLEANING DISPLAY
SECTION (CLEAN)
15
Select a drive and
operate project data
files
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
(
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
13-18, 13-19
10
Displaying file, folder data
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
Function
UTILITY FUNCTION
13.2.3
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 17
 Display example of Project information
Project information
Storage file/folder display screen
Project information
(2)
(3)
(4)
(7)
(5)
(6)
(8)
(9)
(1)
Number
Item
Description
(1)
Select drive
The drive by which a file or folder is displayed can be selected.
When the SD card is not installed, [A:Built-in SD card] is not displayed.
If the USB memory is not installed, [E: USB drive] is not displayed.
(2)
Kind
Indicates the type of the displayed name (file or folder).
The file is indicated with an extension, while the folder is indicated with "DIR."
(3)
Name
Displays the project data (Project Folder) in the selected drive.
When the name exceeds 18 characters, the 19th and later characters are not displayed.
The project data being monitored on the GOT is preceded by "%".
(4)
Path name
Displays the path name of drive/folder which is currently displayed.
(5)
Size
Displays the size of the file displayed in [Name].
(6)
Date and time
Displays the date and time when each file is installed.
(7)
The size of drive
Displays the size in use and the entire size of the drive which is selected by drive selection.
(Only the size in use is displayed when selecting the C drive.)
(8)
Operation switch
Displays the execution switch of functions (download, upload, etc.) which can be carried out in [Project
information].
(9)
Number of files
Displays the total number of the displayed files.
POINT
Folders and files displayed
For the folders and files displayed, refer to the following.
13.1.4 Display file
13 - 18
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
(1) Display operation of Project information
4.
Touching project data selects and inverts it.
10
For operation of delete, copy, property, data check,
download, upload, refer to the following.
Delete.......................................
This section (2)
Copy.........................................
This section (3)
Property....................................
This section (4)
Data check...............................
Download, setup
..................................................
Upload, setup cancel
..................................................
This section (5)
This section (6)
This section (7)
Touching [ ] button closes the screen.
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
2.
3.
Touching a drive in Select drive displays the project
data in the drive.
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
1.
UTILITY FUNCTION
9
 Operation of project information
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
Deletes selected files.
1.
2.
Touch and select the file to delete.
Touching [Del] button displays the screen mentioned
left.
Confirm the deletion targeted file is specified
correctly.
Touching [OK] button deletes the file.
Touching [Cancel] button cancels the deletion.
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
(2) Deletion operation
3.
When the deletion completes, the dialog box shown
left is displayed.
Touching [OK] button closes the dialog.
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 19
(3) Copy operation
Uploads the project data written in the C drive (Flash Memory) to the A drive (Built-in SD card)/E drive (USB
drive).
• Copying to another directory in the same drive
• Copying between A drive and E drive
Copy to/from C drive or copy to C drive/D drive is disabled.
(This item explains using the A drive.)
1.
Install SD card in the PC, in which create a folder for
the copy destination.
Set the same character with [System Setting] of
[System Environment] of GT Designer3 for the folder
name.
GT Designer3 Version1 Screen Design Manual
(Fundamentals)
2.
Install the SD card mentioned above to GOT.
For inserting/removing method of SD card/USB
memory, refer to the following.
8.1.2 Installing and removing procedures of
the SD card
8.2.2 Installing and removing procedures of
the USB memory
3.
Dialog for selecting a copy destination folder
4.
5.
6.
13 - 20
Open [Project Information] screen to select the file to
copy.
Touching [Copy] button displays the message
[Please select a destination.] in the left bottom of the
screen.
If the copy destination folder is touched, the screen
display is changed to the folder of copy destination.
At this time, it cannot be copied into the same folder
where the file exists.
Select other folders.
Touching [Exec.] button displays the dialog box
shown left.
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
When the copy is completed, the dialog of
completion is displayed.
Touching [OK] button closes the dialog.
UTILITY FUNCTION
9
10
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
8.
Touch [OK] button.
If there is no file of the same name in the copy
destination folder, starts to copy.
When there is a file of the same name in the copy
destination folder, the dialog mentioned left is
displayed without starting the copy.
If copy, in this case, the copied file is overwritten to
the project data in the copy destination folder.
Touching [OK] button starts copy.
Touching [Cancel] button cancels the copy.
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
7.
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
Displays the property of the project data in the selected folder.
Touching [Property] button after selecting the project
data to display the property displays the property as
shown left.
In property display, the following information is
displayed.
2.
3.
4.
Description
14
Date
Displays the creation date of the file.
Author
Displays the author of the project data.
Drawing S/W
version
Displays name and version of the drawing
software by which the project data is created.
Touching
by one line.
button scrolls up/down the screen
Touching
by one screen.
button scrolls up/down the screen
Touching [ ] button closes the property display and
returns to the previous screen.
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
Item
13
15
CLEANING DISPLAY
SECTION (CLEAN)
1.
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
(4) Property display operation
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 21
(5) Data check operation
Carries out data check of the selected project file.
When data is normal.
1.
2.
Touch [Data check] button after selecting a data
check target file.
The dialog mentioned left will be displayed after
executing data check.
Touching [OK] button closes the dialog.
When data is erroneous.
(6) Download operation/setup operation
(a) Download operation
Transfers the project data stored in the A drive (Built-in SD Card) or E drive (USB drive) to the C drive
(Flash Memory). (The GOT monitors using the data in the C drive.)
(This item explains using the A drive.)
POINT
Before download operation
(1) Setup cancel
When the project data in the A drive is set up, the project data cannot be downloaded to the C drive.
Execute setup cancel (
(7) (b) Setup cancel operation) before downloading the project data.
(2) Project data to be stored in a SD card
When storing the project data from GT Designer3 to SD card, select [C: Built-in flash memory] for [Project
Data] in the [Boot Drive].
13 - 22
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
8.1.2 Installing and removing procedures of
the SD card
8.2.2 Installing and removing procedures of
the USB memory
3.
4.
Touch [A: Built-in SD card] of [Select drive].
Touching [Download] button displays the screen
shown on the left. Touching [OK] button executes the
download.
10
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
For the SD card installation/removal method, refer to
the following.
UTILITY FUNCTION
9
Mount the SD card/USB memory to GOT.
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
1.
2.
6.
When the download is completed, the dialogue box
shown on the left is displayed.
Touching [OK] button restarts the GOT.
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
If there is a project data of the same name in the C
drive, the screen shown on the left is displayed
without starting the download.
Touching [OK] button executes an overwrite
download to the project data of the same name.
Touching [Cancel] button cancels the download.
14
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
5.
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 23
(b) Setup operation
Sets the project data stored in the A drive (Built-in SD card) to be used in the GOT.
The GOT monitors using the monitor data in the A drive.
POINT
Before setup operation
When storing project data from GT Designer3 to SD card, select [A: Standard SD Card] for [Project Data] in [Boot
Drive].
1.
Mount the SD card to GOT. For the SD card
installation/removal method, refer to the following.
8.1.2 Installing and removing procedures of
the SD card
2.
3.
4.
13 - 24
Touch [A: Built-in SD card] of [Select drive].
Touching [Download] button displays the screen
shown on the left.
Touching [OK] button executes the setup.
When the setup is completed, the dialog box
mentioned left is displayed.
Touching [OK] button restarts the GOT.
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
(a) Upload operation
By upload operation, the project data is transferred from the C drive (Flash Memory) to the A drive (Build-in
SD card) or E drive (USB drive).
The SD card or USB memory after uploading can be used for downloading project data to another GOT.
(This item explains using the A drive.)
UTILITY FUNCTION
9
(7) Upload/setup cancel operation
10
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
POINT
Before upload operation
The project data cannot be uploaded to the A drive when the project data of the A drive is set up.
(7)(b) Setup cancel operation) before uploading the project data.
Execute setup cancel (
3.
11
Touch [A: Built-in SD card] of [Select drive].
Touching [Upload] button displays the screen shown
on the left.
Touching [OK] button executes the upload.
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
1.
2.
If there is a project data of the same name in the A
drive, the screen shown on the left is displayed
without starting the upload.
Touching [OK] button executes an overwrite upload
to the project data of the same name.
Touching [Cancel] button cancels the upload.
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
4.
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
5.
When the uploading is completed, the dialog box
mentioned left is displayed.
Touching [OK] button restarts the GOT.
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 25
(b) Setup cancel operation
By setup cancel, setup is canceled.
1.
2.
3.
4.
13 - 26
Touch [A: Built-in SD card] of [Select drive].
Touching [Upload] button displays the screen shown
on the left.
Touching [OK] button executes the setup cancel.
When the setup cancel is completed, the dialog box
mentioned left is displayed.
Touching [OK] button restarts the GOT.
After restart, the GOT monitors with the project data
in the C drive.
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
9
UTILITY FUNCTION
Hard copy information
 Function of hardcopy information
Carries out delete, copy and move to the file created by the hardcopy function.
For details of hard copy function, refer to the following manual.
GT Designer3 Version1 Screen Design Manual (Functions)
Function
10
Description
Reference
Displaying file, folder data
The file/folder type, name, data size and creating date & time are displayed.
13-28, 13-29
Delete
File is deleted.
13-30
Copy
File is copied.
13-31
Rename
Renames file.
13-32
11
Main menu
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
 Display operation of Hardcopy information
Program/data control
9.3 Utility Display)
12
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
Touch
[Hard copy information]
Touch
[Program/data control]
Hard copy information
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
13
Select a drive and
operate hard copy
data files
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
(
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
13.2.4
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 27
 Display example of Hardcopy information
Hard copy information
Storage file/folder display screen
Hard copy information
(2)
(3)
(4)
(5)
(7)
(6)
(8)
(9)
(1)
Number
Item
Description
(1)
Select drive
The target drive which displays file or folder can be selected.
When SD card or USB memory is not installed, the following drives are not displayed.
• SD card: [A: Built-in SD card]
• USB memory: [E: USB drive]
(2)
Kind
Indicates the type of the displayed name (file or folder).
In case of file, displays the extension; in case of folder, displays "DIR".
(3)
Name
Displays the file name or folder name.
For the long file/folder name, entire part may not be displayed.
Confirm the nondisplayed part with the [Copy] button, etc.
(
13.2.4 ■Hardcopy information operation (3) Copy operation)
After confirmation, touch the [Cancel] button to cancel the operation.
(4)
Path name
(5)
Size
Displays the path name of drive/folder which is currently displayed.
Displays the size of the file displayed in [Name].
(6)
Date and time
The date and time when each file was created are displayed.
(7)
The size of drive
Displays the size in use and the entire size of the drive which is selected by drive selection.
(Only the size in use is displayed when selecting the C drive.)
(8)
Operation switch
Execution switch of each function.
(9)
Number of files
Displays the total number of the displayed files.
POINT
(1) Display of creation date and time
The creation date and time display is not updated even if a file is created or updated while displaying the
hardcopy information. To display the updated creation date and time, close the screen currently displayed (by
moving to the upper hierarchy folder, etc.) and display the screen again.
(2) Folders and files displayed
For the folders and files displayed, refer to the following.
13.1.4 Display file
13 - 28
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
9
UTILITY FUNCTION
 Hardcopy information operation
3.
4.
5.
6.
Touching a folder name displays the information of
the touched folder.
Touching a folder of [ . . ] displays the information of
the folder of the one upper hierarchy.
Touching
button of the scrollbar scrolls up/
down the screen by one line.
Touching
button scrolls up/down the screen by
one screen.
Touching a file name selects the file.
For the operations of the delete, copy, and rename,
refer to the following.
Delete......................................
Copy........................................
Rename...................................
7.
Touching [
This section (2)
This section (3)
This section (4)
] button closes the screen.
10
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
2.
Touching a drive of [Select drive] displays the
information of the touched drive.
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
1.
12
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
(1) Display operation of Hardcopy information
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
13
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 29
(2) Deletion operation
Deletes selected files.
1.
2.
3.
4.
13 - 30
Touch and select the file to delete.
Touching [Del] button displays the screen mentioned
left.
Touching [OK] button deletes the file.
Touching [Cancel] button cancels the deletion.
When the deletion is completed, the completion
dialog is displayed.
Touching [OK] button closes the dialog.
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
3.
4.
Touch and select the file to copy.
Touching [Copy] button displays the message
[Please select a destination.] in the left bottom of the
screen.
If the copy destination folder is touched, the screen
display is changed to the folder of copy destination.
At this time, it cannot be copied into the same folder
where the file exists.
Select other folders.
Touching [Exec.] button displays the dialog box
shown left.
10
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
1.
2.
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
Copies the selected file.
UTILITY FUNCTION
9
(3) Copy operation
6.
Touch [OK] button.
If there is a file of the same name in the copy
destination folder, the following dialog is displayed
without starting the copy.
Touching [OK] button overwrites the file.
Touching [Cancel] button cancels the copy.
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
5.
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
7.
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
When the copy is completed, the dialog of
completion is displayed.
Touching [OK] button closes the dialog.
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 31
(4) Rename operation
Renames the selected file.
1.
2.
Touch and select the file to change the name.
Touching [Rename] button displays the screen shown
left. Input the file name to be changed.
By touching the following button, input text type is
changed.
[A-Z]: English capital
[0-9]: Numeric/Symbol
3.
4.
5.
13 - 32
Touching [Enter] button displays the dialog box
shown left.
Touching [OK] button starts renaming file.
When renaming is completed, completion dialog box
is displayed.
Touching [OK] button closes the dialog.
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
9
UTILITY FUNCTION
Advanced recipe information
 Function of advanced recipe information
For the advanced recipe file used in advanced recipe function, copy/delete/file output are available.
In addition, it is possible to writing/reading into/from a controller by using this function, without creating the screen to
operate the advanced recipe. (Advanced recipe setting of GT Designer3 is required.)
Function
Description
Displaying file, folder data
The file/folder name, data size and creating date & time are displayed.
G1P
CSV conversion
G1P file of advanced recipe file is converted to CSV file.
13-38
G1P
TXT conversion
G1P file of advanced recipe file is converted to Unicode text file.
13-38
CSV file or Unicode text file is converted to G1P file of advanced recipe file.
13-39
Del
File or folder is deleted.
13-40
Copy
File is copied.
13-41
Move
File is moved.
13-42
Rename
File name is changed.
13-43
Create Folder
New folder is created.
13-44
Create G1P
New G1P file of advanced recipe file is created.
13-45
Load record GOT
PLC
Selected record value is loaded in the device of controller.
13-47
Save record PLC
GOT
The device of controller is saved in selected record.
13-48
Match records GOT
PLC
Selected record is verified to the device value of controller.
13-49
Delete Device Value
The device value contained in selected record is deleted.
13-50
12
13
14
15
CLEANING DISPLAY
SECTION (CLEAN)
Advanced recipe
record list screen
G1P
13-35, 13-37
11
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
CSV/TXT
conversion
Advanced recipe
information screen
Reference
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
GT Designer3 Version1 Screen Design Manual (Functions)
10
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
For writing/reading into/from a controller with this function or editing of advanced recipe file on the personal
computer, refer to the following manual.
Specifications and operating procedure are described.
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
Before using advanced recipe information
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
POINT
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
13.2.5
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 33
 Display operation of Advanced Recipe information
Main menu
(
Program/data control
9.3 Utility Display)
Touch
[Program/data control]
Touch
[Advanced Recipe information]
Advanced Recipe information
13 - 34
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
9
UTILITY FUNCTION
 Display example of Advanced Recipe information
(1) Advanced recipe information screen
Advanced Recipe Information
Storage file/folder display screen
Advanced Recipe Information screen
(2)
(3)
(4)
(6)
(5)
(7)
(8)
(1)
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
Description
Select drive
The target drive can be selected. (Even if SD card is not installed, this message appears.)
(2)
Kind
Indicates the type of the displayed name (file or folder).
In case of file, displays the extension; in case of folder, displays "DIR".
Name
(
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
(3)
12
Displays the file name or folder name.
For the long file/folder name, entire part may not be displayed.
Confirm the nondisplayed part with the [Rename] button, etc.
13.2.5 ■Advanced recipe information operation(7) Rename operation)
After confirmation, touch the [Cancel] button to cancel the operation.
(4)
Path name
Displays the path name of drive/folder which is currently displayed.
(5)
Size
Displays the size of the file displayed in [Name].
(6)
The size of drive
Displays the size in use and the entire size of the drive which is selected by drive selection.
(7)
Operation switch
Execution switch of each function.
(8)
Number of files
Displays the total number of the displayed files.
POINT
(1) About the displayed file
The files other than that for advanced recipe are not displayed on the advanced recipe information screen.
(2) Folders and files displayed
For the folders and files displayed, refer to the following.
13.1.4 Display file
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
Item
(1)
14
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
Number
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
11
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 35
(2) Advanced recipe record list screen
Touching the [Execute] button on the advanced recipe information screen after selecting the advanced recipe
file, this screen appears.
Records selected in each advanced recipe file can be displayed or saved/loaded.
Number
(1)
Item
No.
Description
Record No. of advanced recipe file is displayed.
Attribution of record is displayed.
Attribution of record can be changed with GT Designer3.
(2)
(3)
(4)
(5)
13 - 36
Attr
V: Record can be loaded/saved(Record whose value is selected.)
VP: Record only for loading(Record whose value is selected and cannot be changed.)
Blank: Record only for saving(Record whose value is deleted or not selected.)
P: Record unusable (reserved area)(Record whose value is not selected and cannot be changed.)
Record Comment
Record Comment is displayed.
File Name
Path and name of recipe file are displayed.
Setting No.
Recipe No. is displayed.
Name
Recipe name is displayed.
Operation switch
Execution switch of each function.
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
3.
4.
5.
6.
Touching a folder name of [ . . ] displays the
information of the folder in one upper hierarchy.
Touching
button of the scrollbar scrolls up/
down the screen by one line.
Touching
button scrolls up/down the
screen by one screen.
Touching a file name selects the file.
For operation of operating switches, refer to the
following.
G1P
CSV, G1P
TXT...
This section (2)
CSV/TXT
G1P...............
This section (3)
Delete...................................
This section (4)
Copy.....................................
This section (5)
Move.....................................
This section (6)
Rename................................
This section (7)
Create Folder........................
This section (8)
Create G1P...........................
This section (9)
Execute...................
This section (10) to (13)
10
11
12
13
Touching [ ] button closes the screen.
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
7.
Touching a folder name displays the information of
the touched folder.
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
2.
Touching a drive of [Select drive] displays the
information of the touched drive.
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
1.
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
(1) Display operation of Advanced Recipe information
UTILITY FUNCTION
9
 Advanced recipe information operation
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 37
(2) G1P
CSV conversion operation, G1P
TXT conversion operation
Advanced recipe file (G1P file) is converted to CSV file or Unicode text file that can be displayed/edited on
personal computer.
1.
2.
3.
4.
(Example: Dialog box if the [G1P
CSV] button is touched.)
5.
6.
13 - 38
Touch and select the G1P file to convert into a
CSV file or a Unicode text file.
Touch the following button in accordance with
destination file type.
• CSV file: [G1P
CSV] button
• Unicode text file: [G1P
TXT] button
Select the target folder.
(Selecting a folder is not needed for outputting
directly below the drive.)
Touching [Exec.] button displays the dialog box
shown left.
Touch [OK] button.
(While executing, "Processing..."message
appears on the screen.)
When the file, whose name is the same, exists in
the destination folder, the dialog box shown at left
appears without starting the conversion.
Touching [OK] button overwrites the file.
Touching [Cancel] button cancels the conversion.
The message of completion is displayed in dialog
box when conversion is completed.
Touching [OK] button closes the dialog.
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
CSV file or Unicode text file is converted to an advanced recipe file (G1P file).
1.
To select the file, touch the check box of CSV file
or Unicode text file to be converted to a G1P file.
UTILITY FUNCTION
9
G1P conversion operation
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
Select the target folder.
(Selecting a folder is not needed for outputting
directly below the drive.)
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
2.
Touching [Exec.] button displays the dialog box
shown left.
Touch [OK] button.
(While executing, "Processing..."message
appears on the screen.)
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
3.
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
4.
When the file, whose name is the same, exists in
the destination folder, the dialog box shown at left
appears without starting the conversion.
Touching [OK] button overwrites the file.
Touching [Cancel] button cancels the conversion.
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
5.
The message of completion is displayed in dialog
box when conversion is completed.
Touching [OK] button closes the dialog.
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 39
CLEANING DISPLAY
SECTION (CLEAN)
15
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
(3) CSV/TXT
(4) Deletion operation
Folder and file to be used on advanced recipe are deleted.
1.
2.
Touch and select the file/folder to delete.
Touching [Del] button displays the dialog
mentioned left.
Touching [OK] button deletes the file/folder.
(While executing, "Processing..."message
appears on the screen.)
Touching [Cancel] button cancels the deletion.
When it cannot be deleted, the dialog box shown
at left appears. (Only when deleting folder is
executed.)
Verify that there is no file in the folder and execute
the delete operation again.
(
13.2.6 ■ Precautions)
3.
13 - 40
When the deletion is completed, the completion
dialog is displayed.
Touching [OK] button closes the dialog.
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
9
Folder to be used in advanced recipe is copied.
1.
2.
UTILITY FUNCTION
(5) Copy operation
Touch and select the file to copy.
Touch the [Copy] button.
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
Select the target folder.
(Selecting a folder is not needed for outputting
directly below the drive.)
At this time, it cannot be copied into the same
folder where the file exists.
Select other folders.
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
3.
5.
If there is a file of the same name in the copy
destination folder, the following dialog is displayed
without starting the copy.
Touching [OK] button overwrites the file.
Touching [Cancel] button cancels the copy.
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
Touching [Execute] button displays the dialog box
shown left.
Touch [OK] button.
(While executing, "Processing..."message
appears on the screen.)
14
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
4.
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
6.
CLEANING DISPLAY
SECTION (CLEAN)
15
When the copy is completed, the dialog of
completion is displayed.
Touching [OK] button closes the dialog.
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 41
(6) Move operation
Files to be used in advanced recipe are moved.
1.
2.
3.
4.
5.
6.
13 - 42
Touch and select the file to move.
Touch the [Move] button.
Select the target folder.
(Selecting a folder is not needed for moving
directly below the drive.)
Touching [Execute] button displays the dialog box
shown left.
Touch [OK] button.
(While executing, "Processing..."message
appears on the screen.)
When any file with the same name exists in the
destination folder, the dialog box shown left
appears without starting the movement.
Touching the [OK] button overwrites the file.
Touching [Cancel] button cancels moving.
When moving is completed, completion dialog box
is displayed.
Touching [OK] button closes the dialog.
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
9
(7) Rename operation
1.
UTILITY FUNCTION
File name to be used in advanced recipe is changed.
Touch and select the file to change the name.
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
Touching [Rename] button displays the screen
shown left. Input the file name to be changed.
By touching the following button, input text type is
changed.
[A-Z]: English capital
[0-9]: Numeric/Symbol
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
2.
4.
Touching [Enter] button displays the dialog box
shown left.
13
Touching [OK] button starts renaming file.
(While executing, "Processing..."message
appears on the screen.)
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
3.
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
5.
When renaming is completed, completion dialog
box is displayed.
Touching [OK] button closes the dialog.
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 43
(8) Folder create operation
Folder to be used in advanced recipe is created.
1.
2.
3.
4.
5.
13 - 44
Touch the [Create Folder] button.
The input key window shown left appears, then
input the file name to be created.
By touching the following button, input text type is
changed.
[A-Z]: English capital
[0-9]: Numeric/Symbol
Touching [Enter] button displays the dialog box
shown left.
Touching [OK] button starts creating folder.
When creating folder is completed, completion
dialog box is displayed.
Touching [OK] button closes the dialog.
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
Advanced recipe file (G1P file) is created.
When advanced recipe is only executed on Utility, advanced recipe file should be created with this function in
advance.
1.
Touch the [Create G1P] button.
UTILITY FUNCTION
9
(9) G1P file create operation
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
As the input key window is displayed, input the file
name for new file.
By touching the following button, input text type is
changed.
[A-Z]: English capital
[0-9]: Numeric/Symbol
12
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
3.
The screen to select the advanced recipe setting is
displayed.
Select the advanced recipe setting to be used for
new file.
After selecting, touch the [Next] button.
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
2.
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
11
4.
Touching [Enter] button displays the dialog box
shown left.
Touch [OK] button.
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
(Continued to next page)
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 45
5.
6.
13 - 46
When the file, whose name is the same, exists in
the destination folder, the dialog box shown left
appears without starting the creation.
Touching the [OK] button overwrites the file.
Touching [Cancel] button cancels creating.
When creating is completed, completion dialog
box is displayed.
Touching [OK] button closes the dialog.
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
9
(10) Record load operation
1.
UTILITY FUNCTION
Selected record value is loaded in the device of controller.
Select the recipe file and touch the [Execute]
button.
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
As the Advanced Recipe Record List screen is
displayed, select the record comment to which you
want to load the device value.
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
2.
4.
Touching the [Load record GOT
PLC] button
displays the dialog box shown left.
Touching the [OK] button starts loading record.
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
3.
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
5.
When loading is completed, completion dialog box
is displayed.
Touching [OK] button closes the dialog.
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 47
(11) Record save operation
Device value of a controller is saved in the selected record.
1.
2.
3.
4.
5.
6.
13 - 48
Select the recipe file and touch the [Execute] button.
As the Advanced Recipe Record List screen is
displayed, select the record comment for saving the
device value.
Touching the [Save record PLC
GOT] button
displays the screen shown left.
For changing the record comment of saving
destination, input the record comment.
By touching the following button, input text type is
changed.
[A-Z]: English capital
[a-z]: English minuscule
[0-9]: Numeric/Symbol
Other than alphanumeric and symbol can not be
inputted.
If record comment is not changed, it is not need to input.
Touching [Enter] button displays the dialog box
shown left.
Touching the [OK] button starts saving record.
When saving is completed, completion dialog box is
displayed.
Touching [OK] button closes the dialog.
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
9
(12) Record match operation
1.
UTILITY FUNCTION
Verifies weather selected record matches to the device value of the controller.
After executing loading/saving with advanced recipe, verifies weather its contents are reflected.
Select the recipe file and touch the [Execute]
button.
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
As the Advanced Recipe Record List screen is
displayed, select the record comment for matching
the device value.
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
2.
3.
PLC] button
Touching the[OK] button starts matching record.
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
4.
Touching the [Match records GOT
displays the dialog box shown left.
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
When matching is completed, completion dialog
box is displayed.
Touching [OK] button closes the dialog.
14
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
5.
6.
If selected record does not match to the device
value of controller, the dialog box shown left is
displayed.
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 49
(13) Device value delete operation
The device value of selected record is deleted (without value) and changed to record only for reading.
(The record name is not deleted.)
1.
2.
3.
4.
5.
13 - 50
Select the recipe file and touch the [Execute]
button.
As the Advanced Recipe Record List screen is
displayed, select the record comment to be
deleted.
(If the data of which attribution contains "P" can not
be deleted.)
Touching the [Delete Device Value] button displays
the dialog box shown left.
Touching the [OK] button starts deleting device
value.
(The "Processing..." message is displayed on the
screen.)
When deleting is completed, completion dialog
box is displayed.
Touching [OK] button closes the dialog.
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
9
UTILITY FUNCTION
 Precautions
(1) When creating folder/file
(a) Number of characters set for folder or file name when creating folder/file.
GOT recognizes file location according to path explained below.
Specify folder or file name, and total characters of path cannot exceed 78 characters.
Users only can rename folder or file name.
(Other than folder/file name is automatically printed.)
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
Example: CSV file Path in SD card or USB memory
File name
(1 character)
Drive name
(1 character)
.CSV
Extension
(4 characters)
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
(2 characters)
\
Max. 78 characters
POINT
12
If folder is assigned the hierarchy.
The \ mark is displayed between folder name and folder name, folder name and file name. The \ mark is also
counted as one character.
• COM1 to COM9
• LPT1 to LPT9
• AUX
• NUL
• PRN
• CLOCK$
• CON
In addition, the folder/file name shown below cannot be used.
• The folder name which begins with G1.
• Folder name and file name which begin with . (period).
• Folder name and file name which finish with . (period).
• Folder name and file name which have only . (one period) or ..(two periods).
14
15
CLEANING DISPLAY
SECTION (CLEAN)
For deleting the folder
The folder in which the file exists cannot be deleted.
Delete the folder after having deleted the files.
In addition, on the advanced recipe information screen, the file other than that for advanced recipe is not
displayed on GOT.
When the folder, in which there is no file displayed on the screen, cannot be deleted, confirm whether there
is other file in SD card or USB memory by using personal computer, etc.
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
(c)
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
(b) Character strings that cannot be set to folder/file
The following character strings cannot be used as a folder name or a file name. Even small characters of
those cannot be used.
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
Folder name
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
A :\
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 51
(2) Precautions for operation
(a) Precautions during folder/file operation (Create/Delete/Copy/File output, etc)
Even if SD card access switch has been turned OFF while GOT is processing folders and files, the
processing continues to be executed. (Example: Even if SD card access switch has been turned OFF while
GOT is creating a folder, the folder is created.)
Therefore, do not pull out the SD card while the "Processing..." message is on the screen after SD card
access switch has been turned OFF.
(b) While GOT is accessing to other file (Alarm data, etc)
When folder/file processing for the recipe is executed while the GOT is in access to other file (SD card
access LED ON), the GOT executes folder/file processing for the Advanced Recipe after the processing for
other file has completed.
Therefore, it may take some time to finish the process of advanced recipe folder/file. (The "Processing..."
message is displayed on the screen.)
POINT
Estimation of processing time
The process may take time depending on the setting of advanced recipe file to be operated. (The more number of
blocks increases, the longer it takes to process advanced recipe folder/file.)
Also, the process to create the first file may take time depending on the setting of advanced recipe file.
(Reference value)
Direct connection to QCPU and CPU(device point:32767 points setting, transmission speed: 115200bps)
• When the block setting number to 1: about 17 seconds
• When the block setting number to 2048: about 4 minutes
(c)
13 - 52
For executing the saving/loading of device value with advanced recipe file which has been moved or whose
name has been changed.
Adjust [Recipe File] setting of advanced recipe setting with GT Designer3 to file which has been moved or
whose name has been changed.
After the setting has been changed, download the advanced recipe setting to GOT.
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
9
UTILITY FUNCTION
Logging information
 Function of logging information
Logging files created with the logging function can be copied, deleted or renamed, etc.
Without using a PC, you can manage logging files on the GOT.
For details of the logging function, refer to the following manual.
10
GT Designer3 Version1 Screen Design Manual (Functions)
Function
Description
Reference
Displaying file, folder data
The file/folder name, data size and creating date & time are displayed.
13-54, 13-55
G1L
CSV conversion
G1L file of loggingfile is converted to CSV file.
13-56
G1L
TXT conversion
G1L file of loggingfile is converted to Unicode text file.
13-56
Del
File or folder is deleted.
13-57
Copy
File is copied.
13-58
Move
File is moved.
13-59
Rename
File name is changed.
13-60
Create Folder
New folder is created.
13-61
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
11
 Display operation of Logging information
Program/data control
9.3 Utility Display)
Touch
[Program/data control]
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
Touch
[Logging information]
Logging information
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
Select a drive and
operate logging data
files
CLEANING DISPLAY
SECTION (CLEAN)
15
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
(
12
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
Main menu
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
13.2.6
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 53
 Display example of Logging information
Logging Information
Storage file/folder display screen
Logging Information
(2)
(3)
(6)
(4)
(7)
(5)
(8)
(1)
Number
Item
Description
(1)
Select drive
The target drive can be selected. (Even if SD card is not installed, this message appears.)
(2)
Kind
Indicates the type of the displayed name (file or folder).
In case of file, displays the extension; in case of folder, displays "DIR".
(3)
Displays the file name or folder name.
For the long file/folder name, entire part may not be displayed.
Confirm the nondisplayed part with the [Rename] button, etc.
Name
(
13.2.6 ■Logging information operation (6)Rename operation)
After confirmation, touch the [Cancel] button to cancel the operation.
(4)
Path name
Displays the path name of drive/folder which is currently displayed.
(5)
Size
Displays the size of the file displayed in [Name].
(6)
The size of drive
Displays the size in use and the entire size of the drive which is selected by drive selection.
(7)
Operation switch
Execution switch of each function.
(8)
Number of files
Displays the total number of the displayed files.
POINT
(1) About the displayed file
The files other than that for logging are not displayed on the logging information screen.
(2) Folders and files displayed
For the folders and files displayed, refer to the following.
13.1.4 Display file
13 - 54
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
3.
4.
5.
6.
7.
Touching a folder name displays the information of
the touched folder.
Touching a folder name of [ . . ] displays the
information of the folder in one upper hierarchy.
Touching
button of the scrollbar scrolls up/
down the screen by one line.
Touching
button scrolls up/down the
screen by one screen.
Touching a file name selects the file.
For operation of operating switches, refer to the
following.
G1L
CSV, G1L
TXT...
This section (2)
Delete...................................
This section (3)
Copy.....................................
This section (4)
Move.....................................
This section (5)
Rename................................
This section (6)
Create Folder........................
This section (7)
Touching [ ] button closes the screen.
10
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
2.
Touching a drive of [Select Drive] displays the
information of the touched drive.
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
1.
12
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
(1) Display operation of logging information
UTILITY FUNCTION
9
 Logging information operation
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
13
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 55
(2) Operation of G1L
CSV conversion G1L
TXT conversion
Logging file (G1L file) is converted to CSV file or Unicode text file that can be displayed/edited on PC.
1. Touch and select the G1L file to convert into a
CSV file or a Unicode text file.
2.
Touch the following button in accordance with
destination file type.
• CSV file: G1L
CSV button
• Unicode text file: G1L
3.
4.
(Example: Dialog box if the [G1L
CSV] button is touched.)
5.
6.
13 - 56
TXT button
Select the target folder.
(Selecting a folder is not needed for outputting
directly below the drive.)
Touching [Execute] button displays the dialog box
shown left.
Touch [OK] button.
(While executing, "Processing..."message
appears on the screen.)
When the file, whose name is the same, exists in
the destination folder, the dialog box shown at left
appears without starting the conversion.
Touching [OK] button overwrites the file.
Touching [Cancel] button cancels the conversion.
The message of completion is displayed in dialog
box when conversion is completed.
Touching [OK] button closes the dialog.
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
9
(3) Deletion operation
1.
UTILITY FUNCTION
Folder and file to be used on logging are deleted.
Touch and select the file/folder to delete.
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
Touching [Del] button displays the dialog
mentioned left.
Touching [OK] button deletes the file/folder.
(While executing, "Processing..."message
appears on the screen.)
Touching [Cancel] button cancels the deletion.
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
2.
When the deletion is completed, the completion
dialog is displayed.
Touching [OK] button closes the dialog.
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
3.
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
When it cannot be deleted, the dialog box shown
at left appears. (Only when deleting folder is
executed.)
Verify that there is no file in the folder and execute
the delete operation again.
(
13.2.6 ■ Precautions)
15
CLEANING DISPLAY
SECTION (CLEAN)
4.
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 57
(4) Copy operation
Folder to be used in logging is copied.
1.
2.
3.
4.
5.
6.
13 - 58
Touch and select the file to copy.
Touch the [Copy] button.
Select the target folder.
(Selecting a folder is not needed for outputting
directly below the drive.)
At this time, it cannot be copied into the same
folder where the file exists.
Select other folders.
Touching [Execute] button displays the dialog box
shown left.
Touch [OK] button.
(While executing, "Processing..."message
appears on the screen.)
If there is a file of the same name in the copy
destination folder, the following dialog is displayed
without starting the copy.
Touching [OK] button overwrites the file.
Touching [Cancel] button cancels the copy.
When the copy is completed, the dialog of
completion is displayed.
Touching [OK] button closes the dialog.
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
9
An operation log file is moved.
1.
2.
UTILITY FUNCTION
(5) Move operation
Touch and select the file to move.
Touch the [Move] button.
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
11
Select the target folder.
(Selecting a folder is not needed for moving
directly below the drive.)
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
3.
5.
When any file with the same name exists in the
destination folder, the dialog box shown left
appears without starting the movement.
Touching the [OK] button overwrites the file.
Touching [Cancel] button cancels moving.
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
Touching [Execute] button displays the dialog box
shown left.
Touch [OK] button.
(While executing, "Processing..."message
appears on the screen.)
14
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
4.
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
6.
When moving is completed, completion dialog box
is displayed.
Touching [OK] button closes the dialog.
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 59
(6) Rename operation
An operation log file is changed.
1.
2.
Touch and select the file to change the name.
Touching [Rename] button displays the screen
shown left. Input the file name to be changed.
By touching the following button, input text type is
changed.
[A-Z]: English capital
[0-9]: Numeric/Symbol
3.
4.
5.
13 - 60
Touching [Enter] button displays the dialog box
shown left.
Touching [OK] button starts renaming file.
(While executing, "Processing..."message
appears on the screen.)
When renaming is completed, completion dialog
box is displayed.
Touching [OK] button closes the dialog.
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
9
(7) Folder create operation
1.
UTILITY FUNCTION
An operation log folder is created.
Touch the [Create Folder] button.
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
[A-Z]: English capital
[0-9]: Numeric/Symbol
4.
12
Touching [Enter] button displays the dialog box
shown left.
Touching [OK] button starts creating folder.
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
3.
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
The input key window shown left appears, then
input the file name to be created.
By touching the following button, input text type is
changed.
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
2.
5.
When creating folder is completed, completion
dialog box is displayed.
Touching [OK] button closes the dialog.
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 61
 Precautions
(1) When creating folder/file
(a) Number of characters set for folder or file name when creating folder/file.
GOT recognizes file location according to path explained below.
Specify folder or file name, and total characters of path cannot exceed 78 characters.
Users only can rename folder or file name.
(Other than folder/file name is automatically printed.)
Example: CSV file Path in SD card or USB memory
A :\
Folder name
(2 characters)
\
File name
(1 character)
Drive name
(1 character)
.CSV
Extension
(4 characters)
Max. 78 characters
POINT
If folder is assigned the hierarchy.
The \ mark is displayed between folder name and folder name, folder name and file name. The \ mark is also
counted as one character.
(b) Character strings that cannot be set to folder/file
The following character strings cannot be used as a folder name or a file name. Even small characters of
those cannot be used.
• COM1 to COM9
• LPT1 to LPT9
• AUX
• NUL
• PRN
• CLOCK$
• CON
In addition, the folder/file name shown below cannot be used.
• The folder name which begins with G1.
• Folder name and file name which begin with . (period).
• Folder name and file name which finish with . (period).
• Folder name and file name which have only . (one period) or ..(two periods).
(c)
For deleting the folder
The folder in which the file exists cannot be deleted.
Delete the folder after having deleted the files.
In addition, on the logging information screen, the files other than logging files are not displayed on GOT.
When the folder, in which there is no file displayed on the screen, cannot be deleted, confirm whether there
is other file in SD card or USB memory by using personal computer, etc.
(2) Precautions for operation
(a) Precautions during folder/file operation (Create/Delete/Copy/File output, etc)
Even if SD card access switch has been turned OFF while GOT is processing folders and files, the
processing continues to be executed.
(Example: Even if SD card access switch has been turned OFF while GOT is creating a folder, the folder is
created.)
Therefore, do not pull out the SD card while the "Processing..." message is on the screen after SD card
access switch has been turned OFF.
(b) While GOT is accessing to other file (Alarm data, etc)
When folder/file processing for the logging is executed while the GOT is in access to other files (SD card
access LED ON), the GOT executes folder/file processing for the logging after the processing for other files
is completed.
Therefore, it may take some time to finish the process of the logging folder/file.
(The "Processing..." message is displayed on the screen.)
13 - 62
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
9
Memory card format
UTILITY FUNCTION
13.2.7
 Function of the memory card format
Format the SD card/USB memory/Internal SRAM.
 Display operation of Memory card Format
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
Main menu
Program/Data control
9.3 Utility Display)
Touch
[Memory card Format]
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
Touch
[Program/data control]
Move to Memory card format
Memory card Format
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
13
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
(
10
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 63
 Memory card format operation
1.
Mount the SD card/USB memory to GOT.
For inserting/removing method of SD card/USB
memory, refer to the following.
8.1.2 Installing and removing procedures of
the SD card
8.2.2 Installing and removing procedures of
the USB memory
2.
3.
4.
5.
6.
7.
8.
Touch and select the drive to format by drive
selection.
Touching [Format] button displays the password
input screen.
Typing 1 1 1 1 and touching the [Enter] key
display the dialog box shown on the left. (The
password is fixed to 1111.)
Confirm the contents of the dialog box, and touch
[OK] button when execute the format of SD card or
USB memory.
To cancel the memory card format, touch [Cancel]
button.
When touching the [OK] button in
shown left appears for recheck.
, the dialog box
Reconfirm whether to format the SD card or USB
memory.
Touching the [OK] button starts the format.
Touching the [Cancel] button cancels the format of
SD card or USB memory.
When the formatting is completed, the completion
dialog mentioned left is displayed.
Touching the [OK] button closes the dialog box.
POINT
Restrictions on formatting
• When use an unformatted SD card or USB memory in GOT, format the SD card or USB memory by PC. GOT
cannot format the unformatted SD card or USB memory.
• The formatting of GOT does not change the file system (Example: FAT16) of the SD card or USB memory and
inherits the file system before formatting.
13 - 64
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
9
Memory information
 Memory information functions
Displays the flash memory empty area size available for the user of each drive and Boot drive empty area size.
Confirming memory empty space is enabled without connecting a PC.
 Display operation of Memory information
Main menu
10
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
Program/Data control
9.3 Utility Display)
Touch
[Memory informaton]
Touch
[Program/data control]
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
(
UTILITY FUNCTION
13.2.8
Memory information
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
13
 Display example of Memory information
15
Item
CLEANING DISPLAY
SECTION (CLEAN)
(2)
Description
(1)
Flash memory empty area size
Indicates the memory space of each drive available for the user to store files or folders.
The [A: Built-in SD card] is not displayed when SD card is not installed.
If the USB memory is not installed, [E: USB drive] is not displayed.
(2)
Boot drive empty area size
Indicates the empty area size of boot drive specified by the user.
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
Number
(1)
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
13 - 65
13.2.9
USB device status display
 Function of USB device status display
This function displays a list of the USB device connection status in the GOT.
Also, this screen is used to remove the USB device from GOT.
 Display operation of USB device status display
Main menu
(
Program/Data control
9.3 Utility Display)
Touch
[Program/data control]
Touch
[USB device status display]
USB device status display
13 - 66
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
4.
5.
Touching the [Stop] button displays the dialog box
shown left.
Touching the [OK] button execute the preparation of
the USB devices removal.
Touching the [Cancel] button cancels the preparation
of USB devices removal.
10
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
3.
USB mass storage is displayed in Device, and [Stop]
button is displayed in Attach.
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
2.
When the USB device is installed to GOT, the screen
shown left is displayed.
12
When the preparation of removal is ready, the dialog
box shown left is displayed.
Touching the [OK] button closes the dialog box.
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
1.
UTILITY FUNCTION
9
 USB device status display operation
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
13
POINT
When using the USB mouse/keyboard, install [USB mouse/keyboard] of the extended function OS to the GOT.
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
USB mouse/keyboard recognition
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 67
13.2.10 SRAM control
 Function of SRAM control
The SRAM user area usage can be confirmed, data in the SRAM user area can be backed up or restored, and the
SRAM user area is initialized.
For the available functions in the SRAM user area, refer to the following.
GT Designer3 Version1 Screen Design Manual (Functions)
 Display operation of SRAM control
Main menu
(
Program/Data control
9.3 Utility Display)
Touch
[Program/data control]
Touch
[SRAM control]
SRAM control
13 - 68
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
9
UTILITY FUNCTION
 Display example of SRAM control
(2)
(1)
10
(2)
(3)
(4)
(8)
(10)
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
(5)
(6) (7)
(12)
(9)
Item
(1)
Check box
(2)
Function name
(3)
Setting ID
(14)
Description
Touch the check box to select or clear the item.
Displays the used functions in the order of the advanced system alarm, advanced user alarm, and logging
function.
Displays the setting IDs. The setting IDs of the advanced system alarm are not displayed.
(4)
Size
(5)
Setting name
Displays the setting name. For the setting name, only characters within the display range are displayed.
Displays the data size.
(6)
Date and time
Displays the creation date and time of each data.
(7)
Number of selected files
Displays the information of the items currently selected.
SRAM area
Displays the current free space size or total size of the SRAM user area.
(9)
Drive space
Displays the current free space size or total size of the drive selected for [Select drive].
(10)
Initialize all
Initializes all areas of the SRAM user area.
(11)
Initialize selected area
(12)
Select drive
Switches drives to be used for the data backup or restoration in the SRAM user area.
(13)
Restoration
Saves the data in the selected drive to SRAM user area.
The following drives can be switched only when a SD card or USB memory is installed.
• SD card: [A: Built-in SD card]
• USB memory: [E: USB drive]
(14)
Backup all area
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
(8)
12
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
Number
(13)
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
11
(11)
Select each area of the SRAM user area to initialize multiple areas of the SRAM user area.
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
Saves data in the SRAM user area to the selected drive.
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 69
 SRAM control operation
(1) Operation to initialize all or selected areas of the SRAM user area
1.
Perform any of the following operations.
• To initialize all areas of the SRAM user area,
touch the [Initialize all] button.
• To initialize selected areas of the SRAM user area,
select the check box of the area to be initialized,
and then touch the [Initialize selected area] button.
(Example: Dialog box when touching the [Initialize all] button)
2.
3.
The dialog box shown left appears.
Check the description of the dialog box. To initialize
the SRAM user area, touch the [OK] button.
To cancel the initialization, touch the [Cancel] button.
When touching the [OK] button in
shown left appears for recheck.
, the dialog box
Touching the [OK] button starts the initialization.
Touching the [Cancel] button cancels the
initialization.
4.
13 - 70
The completion dialog box appears when the
initialization is completed.
Touching the [OK] button closes the dialog box.
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
1.
To restore data in the drive to the SRAM user area
Select the drive where the data is stored, and then
touch the [Restoration] button.
UTILITY FUNCTION
9
(2) Operation to restore data
The dialog box shown left appears.
Check the description of the dialog box. To restore all
data in the SRAM user area, touch the [OK] button.
To cancel the restoration, touch the [Cancel] button.
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
2.
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
, the dialog box
Touching the [OK] button starts the restoration.
Touching the [Cancel] button cancels the restoration.
4.
The completion dialog box appears when the
restoration is completed.
Touching the [OK] button closes the dialog box.
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
When touching the [OK] button in
shown left appears for recheck.
14
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
3.
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 71
(3) Operation to back up all data in the SRAM user area
1.
2.
3.
To back up data in the SRAM user area to a drive
Select the drive where the data is to be stored, and
then touch the [Backup all area] button.
The dialog box shown left appears.
Check the description of the dialog box. To back up
all data in the SRAM user area, touch the [OK]
button.
To cancel the backup, touch the [Cancel] button.
When touching the [OK] button in
shown left appears for recheck.
, the dialog box
Touching the [OK] button start the backup.
Touching the [Cancel] button cancels the backup.
4.
5.
13 - 72
When the file, whose name is the same, exists in the
destination folder, the dialog box shown left appears
without starting the backup.
Touching [OK] button overwrites the file.
Touching the [Cancel] button cancels the backup.
The completion dialog box appears when the
restoration is completed.
Touching the [OK] button closes the dialog box.
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
 GOT data package acquisition function
The copied data can be utilized for backup or creating the same GOT system by installing the data.
For installation function of the GOT, refer to the following.
16.3 BootOS and Standard Monitor OS Installation Using SD card or USB Memory
 Display operation of GOT data package acquisition
Program/Data control
9.3 Utility Display)
12
Touch
[GOT data package acquisition]
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
Touch
[Program/data control]
GOT data package acquisition
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
13
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
(
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
Main menu
10
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
The GOT data package acquisition copies the installed OS or data in the GOT main unit to the SD card or USB
memory.
• OS (Boot OS, standard monitor OS, communication driver, extended function OS, option OS)
• Special data
• Project data
UTILITY FUNCTION
9
13.2.11 GOT data package acquisition
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 73
13.2.12 Operator information management
 Operator management
(1) Operator management function
The function enables displaying a list of the operator information and adding, changing, or deleting the operator
information to be used.
A password for operator authentication can be changed when the password is out of date.
Functions for the operator authentication (automatic logout time, authentication method, password expiration
date, etc.) can be set.
For details of operator authentication functions, refer to the following manual.
GT Designer3 Version1 Screen Design Manual (Fundamentals)
Function
Description
Reference
Operator management
Enables adding, editing, deleting, importing, and exporting the operator information.
Add operation
Adds operator information to the GOT.
13-74, 13-77
13-78
Edit operation
Edits the operator information stored in the GOT.
13-80
Delete operation
Deletes the operator information stored in the GOT.
13-81
Undo
Restores the current operator information to the previous saved one.
13-82
Import operation
Imports the operator information that is already exported to a SD card to the GOT.
13-83
Export operation
Exports the operator information stored in the GOT to a SD card.
13-84
Password change
Enables changing passwords to be used for login and logout in/out of the GOT.
13-85
Function setting
Enables setting the automatic logout time and password expiration date.
13-87
(2) Display operation of operator management
Main menu
(
Debug & self check
Operator setting menu
9.3 Utility Display)
Touch
[Operator management]
Touch
Touch
[Debug & self
check]
[Operator information
management]
Operator information
management
13 - 74
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
9
UTILITY FUNCTION
(3) Display example of operator management
(a) Operator information management screen
(b)
(c)
(d)
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
(a)
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
11
(e)
(f)
Item
Description
(a)
Operator Name
Displays operator names.
(b)
ID
Displays operator IDs.
(c)
Level
Displays security levels for operators.
(d)
Update
Displays the last updated dates of the operator information.
(e)
Operation keys
Execution keys for each function
(f)
Drive in use
Displays and sets the storage location for imported and exported operator information.
Touch the item, and then the display switches. (A: Built-in SD card)
The display switches only when USB drive is installed on the GOT.
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
No.
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 75
(b) Operator information edit screen
Touch the [Add] button or touch the [Edit] button with the operator information selected on the Operator
information management screen, and then the Operator information edit screen is displayed.
The operator information can be edited.
(a)
(b)
(c)
(d)
(e)
(f)
(g)
No.
Item
Description
(a)
Operator Name
The operator name to be edited is displayed or input an operator name to be added. (Up to 16
alphanumeric characters)
(b)
Operator ID
The operator ID to be edited is displayed or input an operator name to be added.
(Setting range: 1 to 32766, Maximum number of registrations: 255)
(c)
Level
The operator security level to be edited is displayed or input an operator security level to be added. (0 to
15)
(d)
Password
Input a password. (Up to 16 alphanumeric characters.)
(e)
Make a permanent password
(f)
Use ext. auth. ID
(g)
Ext.auth. ID
Switches the setting of the item disabled and enabled.
(
: Disabled
: Enabled)
Switches whether to use the external authentication ID.
13 - 76
(
: Not Used
: Used)
The external authentication ID is displayed or input an external authentication ID.
(External authentication ID setting range: alphanumerics*4 to 32 digits)
■ Function setting
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
1.
Touch [Operator management] in the operator setting
menu.
UTILITY FUNCTION
9
(4) Operator management operation
A-Z : Alphabet capital
a-z : Alphabet small letter
4.
When the administrator password is correctly input,
the Operator information management screen in
displayed.
For operating operation switches, refer to the
following.
Add.......................................
This section(4) (a)
Edit.......................................
This section(4) (b)
Delete...................................
This section(4) (c)
Undo.....................................
This section(4) (d)
Import...................................
This section(4) (e)
Export...................................
This section(4) (f)
After all settings are completed, touch the [Save]
button, and then the settings are saved.
Touch the
button without touching the [Save]
button, and then the dialog box shown left is
displayed.
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
When the input is completed, touch the [Enter] key.
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
0-9 : Numeric
3.
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
The Admin password authentication screen is
displayed, and then input the administrator
password.
Character types to be input can be changed with
touching the following buttons.
14
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
2.
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 77
(a) Add operation
Add operator information to the GOT.
1.
2.
(a)
Touch the [Add] button.
The Operator information edit screen is displayed,
and then touch an item to be edited.
(a) OperatorName
(b) OperatorID
(c) Level
(d) Password
(e) Make a permanent password
(f) Use ext. auth. ID
(g) Ext.auth. ID
Touch the OperatorName, and then the Operator
name input dialog box is displayed. Input an
operator name.
Character types to be input can be changed with
touching the following buttons.
A-Z : Alphabet capital
a-z : Alphabet small letter
0-9 : Numeric
When the input is completed, touch the [Enter] key.
(b)
Touch the OperatorID, and then the Operator ID
input dialog box is displayed.
Input an operator ID.
When the input is completed, touch the [Enter] key.
(c)
Touch the level, and then the Operator level input
dialog box is displayed. Input an operator level.
When the input is completed, touch the key.
When the level of the operator being login is
changed during editing the operator information, a
new level is not reflected until you log out of the
GOT once and log in the GOT again.
13 - 78
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
: Disabled
: Enabled
(f)
For using the external authentication ID, touch the
check box "Use ext. auth. ID" and switch the
setting.
: The external authentication ID is not used.
: The external authentication ID is used.
(g)
Touch Ext.auth ID to display the external
authentication ID input dialog box, and enter the
external recognition ID. When the input is
completed, touch the [Enter] key.
When the authentication method is set to
"Fingerprint auth" or "External auth (general)", the
external authentication ID can be input with the
external authentication device.
3.
Touch the [OK] button after all items are input, and
then the dialog box shown left is displayed and the
input operator information is added.
UTILITY FUNCTION
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
For enabling the setting of [Make a permanent
password], touch the check box for [Make a
permanent password], and then the setting is
switched.
9
12
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
(e)
For changing passwords during editing, touch the
password.
The New password input dialog box is displayed,
and then input a password.
When the input is completed, touch the [Enter] key.
When the password input is completed, the New
password input confirmation dialog box is
displayed.
Input the same password.
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
(d)
15
CLEANING DISPLAY
SECTION (CLEAN)
Touch the [Cancel] button or the
button, and then
the dialog box shown left is displayed.
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 79
(b) Edit operation
Edit the operator information stored in the GOT.
1.
2.
3.
4.
Select the operator information to be edited with
touching the operator information.
Touch the [Edit] button.
The Operator information edit screen is displayed,
and then touch an item to be edited.
(a) Level
(b) Password
(c) Make a permanent password
(d) Use ext. auth. ID
(e) Ext.auth. ID
For how to edit operator information, refer to the
following.
This section(4)
Touch the [OK] button after all items are input, and
then the dialog box shown left is displayed and the
input operator information is added.
Touch the [Cancel] button or the
button, and then
the dialog box shown left is displayed.
13 - 80
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
1.
Select the operator information to be deleted with
touching the operator information.
UTILITY FUNCTION
9
Delete operation
Delete the operator information stored in the GOT.
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
3.
Touch the [Delete] button, and then the dialog box
shown left is displayed.
Touch the [OK] button, and then the selected
operator information is deleted.
Touch the [Cancel] button, and then the delete
operation is canceled.
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
2.
4.
Touch the [OK] button, and then the dialog box is
closed.
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
5.
When the delete operation is completed, a
completion dialog box is displayed.
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
(c)
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 81
(d) Undo operation
Restore the current operator information to the previous saved one.
1.
2.
3.
Touch the [Undo] button.
The dialog box shown left is displayed, and then
touch the [OK] button.
The Admin password authentication screen is
displayed, and then input the administrator
password.
Character types to be input can be changed with
touching the following buttons.
A-Z : Alphabet capital
a-z : Alphabet small letter
0-9 : Numeric
When the input is completed, touch the [Enter] key.
4.
13 - 82
When the administrator password is correctly input,
the current operator information is restored to the
previous saved one.
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
9
1.
UTILITY FUNCTION
(e) Import operation
Import the operator information that is already exported to a SD card to the GOT.
Touch the [Import] button.
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
0-9 : Numeric
When the input is completed, touch the [Enter] key.
When the administrator password is correctly input,
the dialog box shown left is displayed and the
operator information stored in a SD card is imported
to the GOT.
12
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
3.
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
The dialog box shown left is displayed.
Touch button, and then the Admin password
authentication screen is displayed.
Input the administrator password.
Character types to be input can be changed with
touching the following buttons.
A-Z : Alphabet capital
a-z : Alphabet small letter
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
2.
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 83
(f)
Export operation
Export the operator information stored in the GOT to a SD card.
1.
2.
3.
Touch the [Export] button.
The dialog box on the left is displayed.
Touch the following buttons according to the output
format for the file.
Binary file: Binary button
CSV file: CSV button
4.
The dialog box shown left is displayed.
Touch [OK] button, and then the Admin password
authentication screen is displayed.
Input the administrator password.
Character types to be input can be changed with
touching the following buttons.
A-Z : Alphabet capital
a-z : Alphabet small letter
0-9 : Numeric
When the input is completed, touch the [Enter] key.
5.
13 - 84
When the administrator password is correctly input,
the dialog box shown left is displayed and the
operator information stored in the GOT is exported to
a SD card.
(file name: AUTHINF.G1U)
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
(1) Password change function
The passwords to be used for the operator authentication can be changed.
For the password change, log into the GOT in advance with the operator name corresponding to the password
to be changed.
(2) Display operation of password change
Debug & self check
Operator setting menu
9.3 Utility Display)
11
Touch
Touch
[Debug & self
check]
[Operator information
management]
[Password change]
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
Touch
12
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
Password change
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
13
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
(
10
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
Main menu
UTILITY FUNCTION
9
 Password change
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 85
(3) Password change operation
1.
2.
3.
Log into the GOT with the operator name
corresponding to the password to be changed on the
Main Menu screen for the utility.
Touch [Password change] in the operator setting
menu, and then the Password change dialog box is
displayed.
Input the current password on the Password change
dialog box.
Character types to be input can be changed with
touching the following buttons.
A-Z : Alphabet capital
a-z : Alphabet small letter
0-9 : Numeric
When the input is completed, touch the [Enter] key.
4.
5.
6.
13 - 86
Input a new password.
After inputting a new password, input the new
password again.
When the new password is correctly input, the dialog
box shown left is displayed and the password is
changed.
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
The functions for the operator information can be set.
The following items can be set.
Description
Reference
Automatic logout time
The time from when the last time the GOT is operated until when you automatically log out of the GOT can be
set.
(1 to 60 minutes, 0 is invalid.)
13-88
Auth method
The authentication method can be switched. ([Operator name + password], [External auth (general)])
When [External auth (general)] is selected, the check box for [Operator name + password] is displayed.
13-88
Password expiration date
Set the item for regularly changing the password to be used for the operator authentication. (1 to 1000 days, 0
is invalid.)
When the password is out of date after setting the password, the GOT requests the password change.
13-89
Initial position input
Set the initial position input (byte count) of external authentication ID from among the data read from the
external authentication device. (0 to 1998 bytes)
Valid byte count input
Set the valid byte count for external authentication ID. (2 to 16 bytes)
11
-
(2) Display operation of function setting
Main menu
Debug & self check
Operator setting menu
12
Touch
[Debug & self
check]
[Operator information
management]
Touch
13
[Function setting]
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
Touch
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
9.3 Utility Display)
Function setting
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
(
10
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
Items
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
(1) Function setting function
UTILITY FUNCTION
9
 Function setting
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 87
(3) Function setting operation
1.
2.
Touch [Function setting] in the operator setting
menu, and then the Admin password
authentication dialog box is displayed.
Input the administrator password.
Character types to be input can be changed with
touching the following buttons.
A-Z : Alphabet capital
a-z : Alphabet small letter
0-9 : Numeric
When the input is completed, touch the [Enter]
key.
3.
When the administrator password is correctly
input, the Function setting screen in displayed.
Touch an item to be set.
(a) Automatic logout time
(b) Auth method
(c) Password expiration date
(d) Initial position input
(e) Valid byte count input
(a) Touch [Automatic logout time], and then the
Automatic logout time edit dialog box is
displayed. Input the time.
When the input is completed, touch the [Enter]
key.
(b) Authentication method
Switch the authentication method.
Touch the item to switch the display between
[Operator name + password]
[External auth
(general)]
[Fingerprint auth]
[Operator
name + password].
13 - 88
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
(e) Valid byte count input
Set the valid byte count for external
authentication ID.
(Only available when the external authentication
(general) is set as the authentication method.)
4.
Touch the [OK] button after all items are input,
and then the dialog box shown left is displayed
and the input setting is saved.
UTILITY FUNCTION
10
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
(d) Initial position input
Set the initial position input (byte count) of
external authentication ID from among the data
read from the external authentication device.
9
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
(c) Touch [Password expiration date], and then the
Password expiration date edit dialog box is
displayed.
Input the expiration date.
When the input is completed, touch the [Enter]
key.
Touch the [Cancel] button or the
button, and
then the dialog box shown left is displayed.
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
13
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 89
 Display example of GOT data package acquisition
Number
Item
Description
(1)
Select drive
Displays the drive where OS and data can be copied.
The [A: Built-in SD card] is not displayed when SD card is not installed.
If the USB memory is not installed, [E: USB drive] is not displayed.
(2)
Copy
Touching the button starts copying.
 GOT data package acquisition operation
(4) Display operation of GOT data package acquisition
The GOT data package acquisition copies the installed OS or data in the GOT main unit to the SD card or USB
memory.
(This item explains using the A drive.)
1.
2.
3.
13 - 90
Touching the drive name below [Select Drive] inverts
the touched drive name.
Touching the [Copy] button starts copying.
The display depends on the status of copy
destination and setup.
Operate with following the displayed dialog box.
After copying OS and data, the dialog box for
notifying the completion appears.
Touching the [OK] button closes the dialog box.
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
9
UTILITY FUNCTION
POINT
Estimation of processing time
The time required for the processing depends on conditions such as OS, data capacity, and file structure.
(Reference value)
• When the capacity is 4 Mbytes: Around 6 seconds
• When the capacity is 12 Mbytes: Around 18 seconds
(a) Copying project data
If the Boot source drive and copy destination drive for project data is the same, the project data cannot be
copied.
If the drives are the same, cancel the setup.
(b) When project data are copied to the GOT
If OS or project data is copied to the GOT using the SD card or USB memory created with GOT data
package acquisition, the utility setting is also copied.
Check each utility setting after copying to the GOT and change the setting according to need.
12
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
SD card or USB memory to be used
When performing GOT data package acquisition, do not store other data to the SD card or USB memory.
If doing so, the previous data will be unavailable.
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
13
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
(c)
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
(5) Precautions for operation
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
13 - 91
13 - 92
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
13.2 Various Data Control
14. GOT SELF CHECK (DEBUG AND
SELF CHECK)
UTILITY FUNCTION
9
Reference
System monitor, A list editor, FX list editor, Backup/restoration
14-1
Self check
Memory check, Display check, Touch panel check, I/O check, Ethernet status check
14-3
System alarm display
GOT error, CPU error
14-19
GOT start time
GOT start time
14-21
14.1 Debug
In this manual, the overview of the debugging function is described.
For display contents and operation procedure of debugging, refer to the following manual.
12
GOT1000 Series Extended/Option Functions Manual for GT Works3
The following describes the functions available as the debugging function.
Item
Description
System monitor
The device of PLC CPU and buffer memory of intelligent function module can be monitored or tested.
Reference
14-1
A list editor
The sequence program of ACPU can be list edited.
14-1
FX list editor
The sequence program of FXCPU can be list edited.
14-1
Backup/restoration
Data can be backed up/restored from the controller to GOT, or backup data can be deleted.
14-2
14.1.1
System monitor
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
GOT1000 Series Extended/Option Functions Manual for GT Works3
A list editor
CLEANING DISPLAY
SECTION (CLEAN)
15
MELSEC-A list editor allows changing the sequence programs in ACPU/QCPU (A mode).
For display contents and operation procedure, refer to the following manual.
GOT1000 Series Extended/Option Functions Manual for GT Works3
16
FX list editor
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
14.1.3
13
14
System monitor allows monitoring and changing the devices in controllers.
For display contents and operation procedure, refer to the following manual.
14.1.2
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
Debug
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
Description
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
Item
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
The GOT can display the screen for debugging and self-checking.
The following describes the functions available as the debugging and self checking functions.
FX list editor allows changing the sequence programs in an FX PLC.
For display contents and operation procedure, refer to the following manual.
GOT1000 Series Extended/Option Functions Manual for GT Works3
14. GOT SELF CHECK (DEBUG AND SELF CHECK)
14.1 Debug
14 - 1
14.1.4
Backup/restoration
 Display operation of Backup/restoration
Main Menu
(
Debug & self check
9.3 Utility Display)
Debug
Touch
[Debug]
Touch
[Backup/restoration]
Touch
[Debug & self check]
Backup/restoration function
 Operation of Backup/restoration
Backup/restore data from the controller to GOT, or delete backup data with the backup/restoration.
GOT data package acquisition is also possible.
For details of backup/restoration, refer to the following manuals.
GOT1000 Series Extended/Option Functions Manual for GT Works3
14 - 2
14. GOT SELF CHECK (DEBUG AND SELF CHECK)
14.1 Debug
Item
Description
Reference
Carries out write/read check of the SD card, USB memory, built-in flash memory, or internal SRAM.
Memory check
[Password]
14-3
5 9 2 0
Drawing check
Carries out missing bit check, color check and drawing check.
14-6
Font check
Displays the character data on the screen to check visually.
14-10
Touch panel check
Checks whether there are no dead zone area in the Touch key minimum unit (2 dots
2 dots).
14-12
I/O check
Carries out RS-232, RS-422/485 connecting target confirmation and self-loopback check.
14-14
Ethernet status check
Sends a ping to check the Ethernet connection status.
14-17
10
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
The following describes the functions available as the self check function.
UTILITY FUNCTION
9
14.2 Self Check
14.2.1
Memory check
 Memory check function
Memory check function carries out the write/read check of A drive (Built-in SD Card), C drive (Flash Memory), D drive
(Internal SRAM) and E drive (USB memory).
12
Description
Checks whether the memory (Built-in SD card) of the A drive can be read/written normally.
C drive memory check
Checks whether the memory (Flash Memory) of the C drive can be read/written normally.
D drive memory check
Checks whether the memory (Internal SRAM) of the D drive can be read/written normally.
E drive memory check
Checks whether the memory (USB memory) of the E drive can be read/written normally.
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
Function
A drive memory check
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
11
 Display operation of Memory check
Main Menu
Debug & self check
Self check
9.3 Utility Display)
Touch
[self check]
Touch
[Memory check]
14
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
Touch
[Debug & self check]
Memory check
CLEANING DISPLAY
SECTION (CLEAN)
15
16
Select the memory to check
and touch [Check].
14. GOT SELF CHECK (DEBUG AND SELF CHECK)
14.2 Self Check
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
(
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
13
14 - 3
 Memory check operation
Carries out write/read check of memory.
POINT
When drive is not displayed
When the drive (memory) to check is not displayed, confirm the mounting procedure or memory type with reference
to the following.
8.1 SD Card
8.2 USB Memory
When no faults are found in mounting, etc, a memory failure may be arisen.
Replace the SD card or USB memory or built-in flash memory (C drive).
For details of built-in flash memory, contact your local Mitsubishi (Electric System) Service.
The following example explains about Memory Check using built-in flash memory (C drive).
For the Built-in SD card (A drive) memory check, install the SD card before carrying out the same key operations as
built-in flash memory. For the USB drive (E drive) memory check, install the USB memory before carrying out the
check operations.
1.
2.
3.
14 - 4
Select a drive to check in the Select Drive screen in
Memory check and touch [Check] button.
Touching [Check] button displays the dialog box on
the left.
Selecting [OK] button displays the numeric keyboard
window.
Selecting [Cancel] button returns to the initial menu.
Touch to input password ( 5 9 2 0 ) and touch
[Enter] key.
Touching [Enter] key executes read/write check for
the built-in flash memory, which is completed in
around 10 seconds.
14. GOT SELF CHECK (DEBUG AND SELF CHECK)
14.2 Self Check
9
UTILITY FUNCTION
POINT
(1) Password change
The password cannot be changed.
When input password error, the cancel dialog box is
displayed.
Touching [OK] returns to the Memory check screen.
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
11
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
(2) When error is found in memory
When error is found by memory check, the dialog box
indicating the area in which the error occurred is
displayed.
In case of error, contact your local Mitsubishi (Electric
System) Service.
Touching [OK] returns to the Memory check screen.
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
14. GOT SELF CHECK (DEBUG AND SELF CHECK)
14.2 Self Check
14 - 5
14.2.2
Drawing check
 Drawing check function
The drawing check function carries out display checks as missing bit check, color check, basic figure display check,
move check among screens.
 Display operation of drawing check
Main Menu
(
Debug & self check
Self check
9.3 Utility Display)
Touch
[Self check]
Touch
[Display check]
Touch
[Debug & Self check]
Display check
Drawing check
Touch
[Drawing check]
POINT
Notes on drawing check
Missing bits is occurred in the following cases.
• There are parts drawn in different color with the filled color.
• There are parts of basic figure and drawing patterns which are not drawn according to the layout and
procedures described in "
14.2.2 ■ Display operation of drawing check".
When missing bits occurs, contact your local Mitsubishi (Electric System) Service.
14 - 6
14. GOT SELF CHECK (DEBUG AND SELF CHECK)
14.2 Self Check
9
UTILITY FUNCTION
 Drawing check operation
The screen for drawing check can be displayed by touching [Drawing check] on the Display check menu.
(1) Before execute drawing check
Upper-left touch
position
Upper-right touch
position
Red
Purple
Green
Light blue
Yellow
12
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
Black
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
11
(a) Missing bit, Color Check
By touching the upper-right part of the screen, the entire screen color changes in the following order: blue
black
red
purple
green
light blue
yellow
white.
Check missing bit and color visually.
White
13
To (b) Basic
figurecheck screen
Touching the upper right part of the screen at the final color (white screen) displays the following (b) Basic
figure check screen.
(b) Basic figure check
Check whether there is no shape transformation of basic figure or display losses.
The basic figure drawn has 4 types: 1. Filled circle, 2. Line, 3. Rectangle, 4. Ellipse.
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
To Pattern 1 of (c) Move check
among screen
CLEANING DISPLAY
SECTION (CLEAN)
15
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
Blue
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
Touching the upper right part of the screen proceeds to the
next check in each step during drawing check.
Touching the upper left part of the screen returns to the
[Display check] screen.
For GT1455-Q (65536 colors), the screen is displayed in
color (blue, black, red, purple, green, light blue, yellow and
white).
Also, for GT1450-Q (monochrome 16 scales), the screen
color is reduced to monochrome 16 scales and displayed.
This section explains in the case of GT1455-Q (65536
colors).
14. GOT SELF CHECK (DEBUG AND SELF CHECK)
14.2 Self Check
14 - 7
(c)
Move check among screens
• Pattern 1: Shape transformation, color check
The drawn figures are displayed in order and at regular intervals.
If the shape and color are displayed visually in order, it is normal
To Pattern 2
Pattern 1
• Pattern 2: Shape transformation, color check
The drawn figures are displayed in order and at regular intervals.
If the shape and color are displayed visually in order, it is normal.
To Pattern 3
Pattern 2
14 - 8
14. GOT SELF CHECK (DEBUG AND SELF CHECK)
14.2 Self Check
9
UTILITY FUNCTION
• Pattern 3: Shape transformation, color check
The overlapped shapes of pattern 1 and pattern 2 are displayed.
If the shape and color are displayed visually in order, it is normal.
To Pattern 4
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
11
• Pattern 4: Shape check
The drawn figures are displayed in order and at regular intervals.
If the shape and interval are displayed visually in order, it is normal.
Touching the upper right part of the screen returns to the [Display check] screen.
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
To [Display check]
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
13
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
The main screen image after the screen information read and write is executed
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
14. GOT SELF CHECK (DEBUG AND SELF CHECK)
14.2 Self Check
14 - 9
14.2.3
Font check
 Font check function
The font check is a function which confirms fonts installed in GOT. The character data of the font is displayed on the
upper left part of the screen one by one.
 Display operation of Font check
Main Menu
(
Debug & self check
9.3 Utility Display)
Self check
Touch
[Self check]
Touch
[Display check]
Touch
[Debug & Self check]
Display check
Font check
Touch
[Font check]
POINT
Notes on Font Check
Judged as normal if the following characters are correctly displayed. (UNICODE)
• Alphabetic characters etc.
• Hangul characters
• Kanji
: 0x0000 to 0x04F9 (From basic Latin to Kirill)
: 0xAC00 to 0xD7A3 (Hangul / Hangul auxiliary)
: 0x4E00 to 0x9FA5 (CJK integrated Kanjis)
If the characters above are not displayed correctly, the fonts may not be installed. Install the standard monitor OS
again.
14 - 10
14. GOT SELF CHECK (DEBUG AND SELF CHECK)
14.2 Self Check
Font check starts by touching [Font Check] in the [Display check] screen.
The character data of the built-in font (in the built-in flash memory) can be checked visually to confirm the font
drawings by displaying the character data serially on the screen.
(1) Before execute font check
Touching the upper right part of the screen proceeds to the
next check in each step during Font check.
Touching the upper left part of the screen returns to the
[Display check] screen.
UTILITY FUNCTION
9
 Font check operation
Upper-left touch
position
Upper-right touch
position
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
11
12
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
The installed font data is displayed by touching the
upper right part of the screen.
Font data
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
13
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
POINT
Option fonts
15
CLEANING DISPLAY
SECTION (CLEAN)
To display optional fonts, the option font installation is required.
The option fonts are displayed at the end.
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
14. GOT SELF CHECK (DEBUG AND SELF CHECK)
14.2 Self Check
14 - 11
14.2.4

Touch panel check
Touch panel check function
Touch panel check function checks whether there are no dead zone area in 2 dots
2 dots.
 Display operation of Touch panel check
Main menu
(
Debug & self check
Self check
9.3 Utility Display)
Touch
[Self check]
Touch
[Debug & self check]
Touch
[Touch panel check]
Touch panel check
Touch
[OK]
POINT
Notes on Touch panel check
If the touched part is not filled with yellow color, there are the following two possible causes.
1. Display part failure
2. Touch panel failure
In that case, contact your local Mitsubishi (Electric System) Service.
14 - 12
14. GOT SELF CHECK (DEBUG AND SELF CHECK)
14.2 Self Check
Touching [Touch panel check] of self-check displays a black-filled screen over the entire screen area.
1.
Touch a part of the screen.
The touched part becomes a yellow-filled display.
UTILITY FUNCTION
9
 Touch panel check operations
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
Yellow
color
Touching the upper left part returns to the self-check.
12
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
2.
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
11
Black-filled screen
Upper-left touch position
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
13
POINT
Checking the upper left part of the screen
14
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
Only the upper left part of the screen cannot be filled with yellow.
If returns to the self-check by touching the upper left part, judge that the upper left area operates normally.
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
14. GOT SELF CHECK (DEBUG AND SELF CHECK)
14.2 Self Check
14 - 13
14.2.5
I/O check
 I/O check function
The I/O check is a function which checks whether GOT and PLC can communicate with each other.
If I/O check ends normally, the communication interface and the connection cable hardware are normal.
To execute I/O check, the communication driver has to be installed in GOT in advance from GT Designer3.
Note that the GOT restarts when this function is performed.
For the details related to the installation of the communication driver, refer to the following.
GT Designer3 Version1 Screen Design Manual (Fundamentals)
(1) Communication drivers inapplicable to I/O check
When the following communication drivers are used, the I/O check cannot be executed.
Connection type
Connection to MITSUBISHI PLC
Communication driver
Ethernet connection
Ethernet(MELSEC), Q17nNC, CRnD-700
Connection to YASKAWA PLC
YASKAWA GL/CP9200(SH/H)/CP9300MS, Ethernet (YASKAWA)
Connection to YOKOGAWA PLC
YOKOGAWA FA500/FA-M3/STARDOM, Ethernet (YOKOGAWA)
Connection to ALLEN-BRADLEY PLC
EtherNet/IP(AB)
Connection to SIEMENS PLC
SIEMENS S7, SIEMENS S7-200, SIEMENS S7-300/400
Microcomputer connection
Computer
Inverter connection
FREQROL 500/700
MODBUS(R)/TCP connection
MODBUS/TCP
Connection to Azbil control equipment
Azbil SDC/DMC
Connection to RKC temperature controller
RKC SR Mini HG (MODBUS)
 Display operation of I/O Check
Main menu
(
Debug & self check
Touch
[Self check]
Touch
[Debug & self check]
I/O check
14 - 14
Self check
9.3 Utility Display)
14. GOT SELF CHECK (DEBUG AND SELF CHECK)
14.2 Self Check
Touch
[I/O check]
When the connecting target confirmation
communication ends, its result is notified by dialog box.
If the connecting target confirmation communication
ends normally, the dialog box notifying of the normal
termination mentioned left is displayed. Touching [OK]
button after confirming the result returns to [I/O check].
If the dialog box mentioned left is displayed after
selecting connecting target confirmation or during CPU
communication check, confirm the following.
• No misconnection with CPU
(
GOT1000 Series Connection Manual for GT
Works3)
• No missettings of parameter
(
10.2 Communication Detail Setting)
• No hardware error.
(
18. TROUBLESHOOTING)
Touching [OK] button after confirming the result returns
to [I/O check].
10
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
2.
After the CPU communication starts normally, the dialog
box mentioned left notifying that it is on checking, until
the connecting target confirmation communication ends
normally.
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
1.
12
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
Touching [CPU] button carries out the connecting target confirmation communication check.
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
(1) Connecting target confirmation
UTILITY FUNCTION
9
 I/O check operation
Touching [Self] carries out the hardware check of RS-232 interface.
1.
GT14 (Rear face)
Self-loopback
check connector
For preparation for the self-loopback communication
check, insert the connector for self-loopback check
(Customer purchased) shown in the diagram left in
the RS-232 interface.
For this connector, short 2 and 3 pins, 7 and 8 pins
and 4 and 6 pins, respectively.
In the communication setting of the GOT utility, set
the channel number for the RS-232 interface to 0
([None]).
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
432
15
CLEANING DISPLAY
SECTION (CLEAN)
(2) Self-loopback
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
876
14. GOT SELF CHECK (DEBUG AND SELF CHECK)
14.2 Self Check
14 - 15
2.
After selecting [Self], the transferred data and
received data are verified through the self-loopback
connector. When the GOT cannot receive the data
during the data transmission, the dialog box shown
left appears and the GOT restarts in five seconds.
When the dialog box shown left appears, check the
following.
• Check if the pins of the connector for self-loopback
check are incorrectly shorted.
• Check if the channel number for the RS-232
interface is set to 0 ([None]) in the communication
setting of the GOT utility.
(
10.1.3 Communication setting contents)
• Check if the hardware has no problems.
(
18. TROUBLESHOOTING)
3.
4.
5.
14 - 16
During check, the dialog box shown left is displayed.
When the all checks ended normally, the dialog box
shown left is displayed. And the GOT restarts in five
seconds.
When an error occurs, the dialog box that shows the
GOT abnormal termination and the byte with the
error appears, and then the GOT restarts in five
seconds.
When the dialog box shown left appears, check the
following.
• Check if the hardware has no problems.
(
18. TROUBLESHOOTING)
14. GOT SELF CHECK (DEBUG AND SELF CHECK)
14.2 Self Check
Ethernet status check
9
 Ethernet status check function
Ethernet status check is a function that sends a ping to check the connection status with the equipment on the
Ethernet.
 Display operation of Ethernet status check
9.3 Utility Display)
10
Debug & self check
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
Main menu
Self check
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
Touch
[Self check]
Touch
[Ethernet status check]
Touch
[Debug & self check]
Ethernet status check
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
13
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
(
UTILITY FUNCTION
14.2.6
14. GOT SELF CHECK (DEBUG AND SELF CHECK)
14.2 Self Check
14 - 17
 Operation of Ethernet status check
1.
2.
Touch
14 - 18
If touch the select button of [IP address of the other
terminal], a keyboard is displayed. Enter the IP
address of the other terminal with the keyboard.
<Default: 192.168.3.39>
If touch the [Ping transmission] button, a ping is sent
to the IP address entered in [IP address of the other
station].
The timeout time is about 5sec.
• When GOT and PLC are in communication
The dialog box showing [Response received.] is
displayed.
• When a communication error occurs
The dialog box showing [Timeout occurred.] is
displayed.
14. GOT SELF CHECK (DEBUG AND SELF CHECK)
14.2 Self Check
 System alarm function
System alarm is the function to display error code and error message when an error occurs in GOT, controller or
network.
System alarms can be reset on the System alarm display screen.
For details of system alarm, refer to the following manual.
 Display operation of System alarm display
Main menu
Debug & self check
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
9.3 Utility Display)
Touch
[System alarm display]
12
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
Touch
[Debug & self check]
System alarm display
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
13
Touching [Reset] resets the
system alarm display in the
GOT error.
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
(
10
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
GT Designer3 Version1 Screen Design Manual (Fundamentals)
UTILITY FUNCTION
9
14.3 System Alarm Display
14. GOT SELF CHECK (DEBUG AND SELF CHECK)
14.3 System Alarm Display
14 - 19
 Operation of system alarm display
(1) System alarm display resetting
1.
2.
Touch
Eliminate each cause of the system alarm being
occurred.
Error causes can be identified by the error code,
error message and channel No. displayed on the
System alarm screen.
(
18. TROUBLESHOOTING)
A method for resetting system alarm depends on an
error.
• GOT error
Touch [Reset] button to reset system alarms.
• CPU error and Network error
The system alarm is automatically reset after its
cause is eliminated.
POINT
(1) Before resetting the system alarm display in the GOT error
Eliminate the system alarm cause before resetting the system alarm display in the GOT error.
If not eliminated, the system alarm display in the GOT error will not be reset even after the reset operation.
(2) Processings with reset operation
The following data in the system information are also reset.
• GOT error code (Write device)
• GOT error detection signal (System Signal 2-1.b13)
14 - 20
14. GOT SELF CHECK (DEBUG AND SELF CHECK)
14.3 System Alarm Display
9
UTILITY FUNCTION
14.4 GOT start time
 GOT start time function
GOT start time is the function to display the following date and time.
• Start time of GOT
• Current time of GOT
• Operating hours of GOT
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
 Display operation of GOT start time
Main Menu
Debug & self check
9.3 Utility Display)
Touch
[Debug & self check]
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
11
Touch
[GOT start time]
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
Start time
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
13
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
(
14. GOT SELF CHECK (DEBUG AND SELF CHECK)
14.4 GOT start time
14 - 21
 Display of GOT start time
Item
Description
Start Time
Displays the time when the GOT was powered on or reset-restarted (OS installation, communication setting change).
Current Time
Displays the current time.
Operating hours
Displays operating hours of the GOT.
The displayed operating hours is the accumulated time while GOT is powered on or reset-restarted (OS installation,
communication setting change).
When powering off or reset-restarting the GOT, the operating hours is cleared.
POINT
(1) To display correct time
Set the clock of GOT. (
12.1.1 Time setting and display functions)
When the clock has not been set, the correct time is not displayed at [Start Time] and [Current Time].
(2) Time displayed at [Operating hours]
[Operating hours] is displayed irrespective of [Start Time] and [Current Time].
When changing the clock of the GOT, [Operating hours] does not match with the difference between [Current
Time] and [Start Time].
([Operating hours] is not the time calculated from [Current Time] and [Start Time].)
The time displayed at [Operating hours] is a reference for the accumulated time while GOT is powered on or
reset-restarted (OS installation, communication setting change).
14 - 22
14. GOT SELF CHECK (DEBUG AND SELF CHECK)
14.4 GOT start time
15. CLEANING DISPLAY SECTION
(CLEAN)
UTILITY FUNCTION
9
In utility, the screen can be set as not to be effected by touching the screen when clean with clothes.
To clean the GOT, wipe the dirty part with a soft cloth using neutral detergent.
Precautions for cleaning
Do not use chemicals such as thinner, organic solvents and strong acids, since they may cause the protective
sheet to be deformed or the dissolvable paint on the surface to peel off.
In addition, do not use spray solvents since they may cause the electrical failure of the GOT and peripheral
devices.
 Display operation of Clean
Main Menu
Clean
12
9.3 Utility Display)
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
(
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
POINT
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
Touch [Clean]
Even if touch points other than the upper left corner and upper right corner of the screen, the GOT does not operates.
 Operation of Clean
After cleaning the screen, touch the screen following the instruction displayed.
After touching the screen, the screen returns to the Main Menu.
The following screen is displayed.
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
15. CLEANING DISPLAY SECTION (CLEAN)
15 - 1
15 - 2
15. CLEANING DISPLAY SECTION (CLEAN)
9
UTILITY FUNCTION
16. INSTALLATION OF COREOS,
BOOTOS AND STANDARD MONITOR
OS
For executing the GOT utility, install the BootOS and standard monitor OS on the C drive (built-in flash memory) of the
GOT, or set the OS boot drive to [A: Standard SD card] and insert the SD card with OS files into the GOT.
(BootOS is installed in the GOT at factory shipment. It is not necessary to install BootOS when upgrading of it is
unnecessary.)
This chapter explains the installation using GOT.
SD card/
11
GOT
USB memory
BootOS or
standard monitor OS
installation
Write
OS file
When GOT is remote, installed
easily using the CF card/
USB memory
Install the SD
card in GOT
SD card/USB memory *1
GT Designer3
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
GT Designer3
12
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
The GOT can starts without an
OS installed.
Write
OS file
Install the SD
card in GOT
SD card
Set the OS boot
drive to [A: Standard
SD Card].
GOT
SD card/
GOT
13
BootOS or
standard monitor OS
installation
*1
SD card/USB memory
*1
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
USB memory
OS file
upload
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
Install OS from GOT to GOT
using CF card/USB memory.
Install the SD
card/USB
memory in GOT
When execute installation with USB memory, standard monitor OS has to be installed in GOT in advance.
14
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
For the writing of OS in GT Designer3, refer to the following.
GT Designer3 Version1 Screen Design Manual (Fundamentals)
POINT
15
CoreOS
CLEANING DISPLAY
SECTION (CLEAN)
In 16.1 to 16.4 of this chapter, only BootOS and standard monitor OS are described.
For CoreOS, refer to the following.
16.5 CoreOS
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS
16 - 1
16.1 BootOS and Standard Monitor OS Required for
Installation
Under-mentioned BootOS and Standard monitor OS are necessary to execute utility.
OS name
BootOS
Function overview
Required for the control of GOT and the communication between PC and GOT.
Installed at factory shipment.
(BootOS can be installed from GT Designer3 or the SD card. When installed from GT Designer3 or the
SD card, GOT is initialized to be the factory shipment status.)
Required for the GOT operation as the monitoring
function of GOT, installation and deletion of the OS file
or project data, touch key control or display function of
the screen and guidance.
Standard
monitor
OS
System screen data
System screen management information file
TrueType numerical font
12-dot standard font (Gothic)
Required for display and operation of the usercreated screen and utility screen.
Not installed in GOT at factory shipment.
Install it from GT Designer3, or the SD card or
USB memory.
At installation, select [Mincho] or [Gothic] for
the 16-dot standard font.
16-dot standard font (Mincho)
16-dot standard font (Gothic)
16 - 2
16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS
16.1 BootOS and Standard Monitor OS Required for Installation
Storage location
Built-in flash memory
C: \G1BOOT\
SD card that stores data with
OS boot drive set to the A drive
A: \G1BOOT\
Built-in flash memory
C: \G1SYS\
SD card that stores data with
OS boot drive set to the A drive
A: \G1SYS\
For the installation using GOT, the SD card or USB memory storing BootOS or standard monitor OS is required.
For the method of writing BootOS and standard monitor OS in the SD card or USB memory, the following three methods
are available.
10
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
(1) [To Memory Card] from GT Designer3
UTILITY FUNCTION
9
16.2 Prior Preparations for Installing BootOS and
Standard Monitor OS
GT Designer3 Version1 Screen Design Manual (Fundamentals)
(2) Uploading from other GOT (BootOS or standard monitor OS has been installed)
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
(3) Using SD card that stores data with OS boot drive set to A drive
Precautions on writing BootOS, standard monitor OS in SD card or USB memory
When writing BootOS, standard monitor OS, etc. in the SD card or USB memory, be sure to execute by the utility of
other GOT, GT Designer3.
The installation is not executed properly with the SD card or USB memory to which uploaded from the utility of GOT
or copied by software other than GT Designer3.
Note the available capacity of the SD card or USB memory.
The available capacity of BootOS and standard monitor OS can be confirmed by [To Memory Card] of GT
Designer3.
12
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
POINT
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
11
GT Designer3 Version1 Screen Design Manual (Fundamentals)
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
13
14
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
Capacity of standard monitor OS
Available space of the SD card
or USB memory
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS
16.2 Prior Preparations for Installing BootOS and Standard Monitor OS
16 - 3
16.3 BootOS and Standard Monitor OS Installation Using
SD card or USB Memory
There are the following two types for the BootOS, standard monitor OS installation using the SD card or USB memory.
(1) Installing when starting the GOT
(
16.3.1 Installing when starting the GOT)
All the OS and project data stored in the SD card or USB memory are transferred to the GOT when powering on
the GOT. This installing method is effective in the following cases.
• The GOT utility cannot be displayed.
• The standard monitor OS is not installed.
(2) Installing using the data control function (Utility)
(
16.3.2 Installing using the program/data control function (Utility))
By operating the utility, select OS or project data stored in the SD card or USB memory and transfer them to the
GOT.
POINT
Precautions on installing BootOS, standard monitor OS
(1) Installing both BootOS and standard monitor OS
After completing BootOS installation, install standard monitor OS. When installing BootOS, the built-in flash
memory in the GOT is initialized and goes to the status at factory shipment. (All OS and project data are
erased.)
BootOS is installed in the GOT at factory shipment.
It is not necessary to install BootOS when not upgrading it.
(2) Copying project data using SD card or USB memory
After installing BootOS, standard monitor OS, and other OS, download the project data.
At this time, match the version of the standard monitor OS in the GOT with the version of the standard monitor
OS with which the project data was created.
(3) When OS and project data are in the SD card or USB memory (when using GT Designer3)
When installing by pressing the upper left corner of the GOT screen, project data is downloaded after
completion of OS installation.
When installing with the utility, install the OS and download the project data from their respective operation
screens.
(4) Installation cannot be interrupted.
Do not perform any of the following during a BootOS or standard monitor OS installation.
Failure to do so may result in installation failure, causing the GOT malfunction.
• Powering off the GOT
• Pressing the reset button of the GOT
• Turning off the SD card access switch of the GOT
• Removing the SD card or USB memory
If the installation failure and the GOT malfunction occur, take the following action.
• If BootOS installation failed: Install CoreOS.
(
16.5.1 Installing the CoreOS)
• If standard monitor OS installation failed: Install BootOS.
(
16 - 4
16.3.1 Installing when starting the GOT)
16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS
16.3 BootOS and Standard Monitor OS Installation Using SD card or USB Memory
1.
2.
3.
4.
Now installing BootOS.
Reboot.
5.
6.
Power OFF the GOT, switch the SD card access
switch to OFF, and install the SD card where the
BootOS, standard monitor OS or project data is
stored in the SD card interface of the GOT.
Switch ON the SD card access switch of GOT.
Power on the GOT while pressing upper left corner
of the GOT screen. (1-point press installation
function)
The BootOS or standard monitor OS is installed in
the built-in flash memory.
The SD card access LED is lit during the install
execution.
Do not pull out the SD card or power off the GOT
while the SD card access LED is lit.
The GOT restarts automatically after the installation
is completed.
(When the standard monitor OS is already installed,
the GOT restarts by touching the [OK] button.)
After confirming normal restart, switch off the SD
card access switch of the GOT. Confirm that the
card access LED is not lit, and remove the SD card
from the SD card interface of the GOT.
10
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
(1) When installing with SD card
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
 Operation procedure
12
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
The displayed message is different depending on the installation condition of standard monitor OS. When the screen
requesting operation is displayed, operate the GOT according to the instructions on the screen.
UTILITY FUNCTION
9
Installing when starting the GOT
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
16.3.1
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS
16.3 BootOS and Standard Monitor OS Installation Using SD card or USB Memory
16 - 5
(2) When installing with USB memory
1.
2.
3.
Now installing BootOS.
4.
Reboot.
5.
Power off the GOT, and install the USB memory
where the BootOS, standard monitor OS or project
data is stored in the USB interface of the GOT.
The BootOS cannot be stored in the USB memory
where the standard monitor OS or project data is
stored.
Power on the GOT while pressing upper left corner
of the GOT screen. (1-point press installation
function)
The BootOS or standard monitor OS is installed in
the built-in flash memory.
Do not pull out the USB memory or power off the
GOT while install execution.
The GOT restarts automatically after the installation
is completed.
(When the standard monitor OS is already installed,
the GOT restarts by touching the [OK] button.)
After confirming normal restart, remove USB
memory from the USB interface of the GOT.
For removing methods of the USB memory, refer to
the following.
13.2.9 USB device status display
POINT
(1) Drives to be used
When installing OS at power-on, use the A or E drive.
(2) Installation by pressing upper left corner of the GOT screen
When the OS boot drive is set to the A or E drive, installation by pressing upper left corner of the GOT screen
is not available.
16 - 6
16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS
16.3 BootOS and Standard Monitor OS Installation Using SD card or USB Memory
9
UTILITY FUNCTION
Installing using the program/data control function (Utility)
For details on program/data control function, refer to the following.
13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)
POINT
Precaution on executing program/data control function
When execute program/data control function, standard monitor OS has to be installed in GOT in advance. Thus,
this function cannot be used for the initial installation of standard monitor OS after purchasing GOT.
Install standard monitor OS by the following two methods.
(1) GT Designer3
(2) Installing when starting the GOT
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
(1) When installing with SD card
1.
2.
3.
Power OFF the GOT. After SD card access LED is
off, install the SD card in which BootOS, standard
monitor OS or project data is stored in the SD card
interface of GOT.
Switch ON the SD card access switch of GOT.
Display the program/data control function
screen (Utility) on the GOT, and install BootOS,
standard monitor OS from the SD card to GOT.
12
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
 Operation procedure
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
11
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
13
4.
Now installing BootOS.
5.
Reboot.
6.
The SD card access LED is lit during the install
execution.
Do not pull out the SD card or power off the GOT
while the SD card access LED is lit.
The GOT restarts automatically after the installation
is completed.
After confirming normal restart, switch off the SD
card access switch of the GOT. Confirm that the
card access LED is not lit, and remove the SD card
from the SD card interface of the GOT.
14
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
Touch [Install]
15
CLEANING DISPLAY
SECTION (CLEAN)
16.3.2
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS
16.3 BootOS and Standard Monitor OS Installation Using SD card or USB Memory
16 - 7
(2) When installing with USB memory
1.
2.
Install the USB memory in which BootOS, standard
monitor OS or project data is stored in the USB
interface of GOT.
Display the data control function screen (Utility) on
the GOT, and install BootOS, standard monitor OS.
Touch [Install]
3.
Now installing BootOS.
4.
Reboot.
5.
Do not pull out the USB memory or power off the
GOT while install execution.
The GOT restarts automatically after the installation
is completed.
After confirming normal restart, display the USB
device status screen and remove the USB memory
from the USB interface of GOT.
13.2.9 USB device status display
16 - 8
16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS
16.3 BootOS and Standard Monitor OS Installation Using SD card or USB Memory
When installing BootOS, GOT compares the version of the BootOS to be installed with the version of BootOS which
is already installed.
If the major version of BootOS to be installed is old, execute the following operations to prevent it from being
rewritten.
(When installing from GT Designer3, a message is displayed on the PC screen. Follow the instructions in that
message.)
(1) When only BootOS is stored in the SD card or USB memory
2.
The message indicating disabled installation is
displayed.
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
1.
10
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
 BootOS installation
UTILITY FUNCTION
9
16.4 When Installing the Different Version of BootOS,
Standard Monitor OS
Touch the [OK] button to cancel installation.
After canceling installation, restart the GOT.
1.
2.
Skip the BootOS installation and install standard
monitor OS and other OS.
If the standard monitor OS is already stored on the
GOT, the following message is displayed.
Touching the [OK] button executes installation.
Touching the [Cancel] button cancels installation.
After executing or canceling installation, restart the
GOT.
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
(2) When BootOS, standard monitor OS, and other OS are stored in the SD card or USB memory
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
12
1.
2.
The version information and a dialog for selecting
whether or not to continue installation are
displayed.
Touching the [OK] button executes installation.
Touching the [Cancel] button cancels installation.
After executing or canceling installation, restart the
GOT.
15
CLEANING DISPLAY
SECTION (CLEAN)
(3) When the version is the same or newer regardless of the data stored in the SD card or USB memory
(conditions (1) and (2) above)
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
(GOT screen when BootOS is installed from SD card or USB memory)
16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS
16.4 When Installing the Different Version of BootOS, Standard Monitor OS
16 - 9
 Standard monitor OS installation
Match the version of each OS file when installing standard monitor OS.
Standard monitor OS cannot be installed if the version of each OS file does not match.
(When the installation process is discontinued.)
Standard monitor OS : 1. .
(When the installation process is normally executed.)
Standard monitor OS : 2. .
Communication driver : 2.
.
Communication driver : 2.
.
Optional function OS
.
Optional function OS
.
: 2.
: 2.
Please match the number.
POINT
Checking method of BootOS, standard monitor OS version
• Check the version of BootOS or standard monitor OS installed in GOT at [OS information] of the utility.
For details, refer to the following.
13.2.1 OS information
• Check the version of BootOS installed in GOT at product shipment on the rating plate on GOT rear face.
When the Boot OS version is 2 digits,
only the lower digit is printed.
Example H/W version: H
Boot OS version: AD
AA
HD
BootOS
version
16 - 10
BootOS
Version
16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS
16.4 When Installing the Different Version of BootOS, Standard Monitor OS
Rating plate: HD
9
UTILITY FUNCTION
16.5 CoreOS
Install CoreOS only when the GOT will not be the status of factory shipment even when BootOS is installed.
Normally, the CoreOS has not to be installed.
POINT
11
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
When executing the CoreOS installation once, it cannot be canceled on the way.
Do not attempt the following to cancel the installation on the way. The GOT may not operate.
• Powering off the GOT
• Pressing the reset button of the GOT
If the GOT does not operate, please consult your local Mitsubishi (Electric System) Service center or
representative.
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
10
Precautions for installing CoreOS
If the GOT does not recover even when installing the CoreOS, the error may be caused by a hardware failure.
Please consult your local Mitsubishi (Electric System) Service center or representative.
12
Installing the CoreOS
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
16.5.1
 Before installing the CoreOS
(1) Installing procedure
The CoreOS can be installed only when using a SD card.
Installation via USB memory/USB/Ethernet is not available.
13
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
(2) Boot OS
When installing the CoreOS, the latest BootOS is also installed automatically.
(Operation by the user is not required.)
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
16
16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS
16.5 CoreOS
16 - 11
 Installing the CoreOS
1.
Write the CoreOS from GT Designer3 to the SD
card.
For details of GT Designer3 operation, refer to the
following manual.
GT Designer3 Version1 Screen Design
Manual (Fundamentals)
2.
3.
4.
5.
6.
7.
8.
16 - 12
After confirming that the GOT is powered off, install
the SD card in the GOT. After installing, switch the
SD card access switch on.
Powering the GOT on displays the screen on the
left.
To cancel the installation, power the GOT off and
remove the SD card.
Turning the SD card access switch off executes
CoreOS installation.
When the installation is completed, the dialog as
shown on the left is displayed.
(The POWER LED of the GOT blinks (green/
orange) at the installation completion.)
Confirm that the message is displayed and power
the GOT off.
Remove the SD card after powering the GOT off.
Powering the GOT on again displays the screen as
shown on the left.
(The GOT goes to the status of factory shipment.)
Install OS (Standard monitor OS, communication
driver, etc.) or download project data as required.
16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS
16.5 CoreOS
The CoreOS installation is not executed even when installing the SD
card in the GOT.
GOT error.
Contact your local sales office.
The GOT main unit is broken.
Please consult your local Mitsubishi (Electric System) Service center or
representative.
SD card error.
Check whether the SD card can be used.
Installation will be cancelled.
The SD card is defective.
(1) Format the SD card and re-execute.
(2) Replace the SD card.
GOT type and OS version do not match.
Installation will be cancelled.
The GOT type selected at [Core OS write] of the GT Designer3 is not correct.
Confirm the GOT type and perform [Core OS write] again.
The version of OS is not acceptable to this GOT.
Installation will be cancelled.
Confirm the version of OS.
Install CoreOS from the latest GT Designer3.
Memory card access switch is off.
Installation will be cancelled.
Turn on the switch and restart the GOT.
The SD card access switch is off. Turn the switch on and restart the GOT.
10
11
12
FILE DISPLAY AND
COPY (PROGRAM/DATA
CONTROL)
13
GOT SELF CHECK
(DEBUG AND SELF
CHECK)
14
CLEANING DISPLAY
SECTION (CLEAN)
15
16
INSTALLATION OF
COREOS, BOOTOS AND
STANDARD MONITOR OS
The message
is displayed
on the GOT
Action
(1) Check whether the SD card access switch of the GOT is on.
If the switch is off, switch it on.
(2) The writing from the GT Designer3 to the SD card may not have been
completed normally.
Execute the writing from the GT Designer3 to the SD card again.
COMMUNICATION
INTERFACE SETTING
(COMMUNICATION SETTING)
Error
DISPLAY AND
OPERATION SETTINGS
(GOT SET UP)
When the CoreOS cannot be installed, confirm the following item.
If the CoreOS cannot be installed even after checking the following item, the error may be caused by a hardware failure.
Please consult your local Mitsubishi (Electric System) Service center or representative.
UTILITY FUNCTION
9
When the CoreOS cannot be installed
CLOCK SETTINGS AND
BATTERY STATUS DISPLAY
(TIME SETTING AND DISPLAY)
16.5.2
16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS
16.5 CoreOS
16 - 13
16 - 14
16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS
16.5 CoreOS
17. MAINTENANCE AND INSPECTION
MAINTENANCE AND
INSPECTION
WARNING
• When power is on, do not touch the terminals.
Doing so can cause an electric shock or malfunction.
• Connect the battery correctly.
Do not discharge, disassemble, heat, short, solder or throw the battery into the fire.
Incorrect handling may cause the battery to generate heat, burst or take fire, resulting in injuries or fires.
• Before starting cleaning or terminal screw retightening, always switch off the power externally in all phases.
Not doing so can cause the unit to fail or malfunction.
Undertightening can cause a short circuit or malfunction.
Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit.
[STARTUP AND MAINTENANCE
PRECAUTIONS]
TROUBLESHOOTING
18
CAUTION
• Do not disassemble or modify the unit.
Doing so can cause a failure, malfunction, injury or fire.
• Do not touch the conductive and electronic parts of the unit directly.
Doing so can cause a unit malfunction or failure.
• The cables connected to the unit must be run in ducts or clamped.
Not doing so can cause the unit or cable to be damaged due to the dangling, motion or accidental pulling of the
cables or can cause a malfunction due to a cable connection fault.
• When unplugging the cable connected to the unit, do not hold and pull the cable portion.
Doing so can cause the unit or cable to be damaged or can cause a malfunction due to a cable connection fault.
• Before touching the unit, always touch grounded metal, etc. to discharge static electricity from human body, etc.
Not doing so can cause the unit to fail or malfunction.
[DISPOSAL PRECAUTIONS]
CAUTION
• When disposing of the product, handle it as industrial waste.
The GOT does not include consumable components that will cause the shorten life.
However, the battery, liquid crystal display screen and backlight have each life length.
It is recommended to replace the battery periodically.
(For the replacement of the liquid crystal screen and backlight, please consult your nearest sales office or FA center.)
For the life of the liquid crystal display screen or backlight, refer to the following.
3.2 Performance Specifications
17. MAINTENANCE AND INSPECTION
17 - 1
APPENDICES
[STARTUP AND MAINTENANCE
PRECAUTIONS]
17
17.1 Daily Inspection
 Daily inspection items
No.
1
Inspection Item
Inspection Method
Connection
status
Usage
status
3
Action
Check for loose
mounting screws.
Securely mounted
Retighten screws within the specified torque
range.
Loose terminal screws
Retighten screws with
screwdriver.
Not loose
Retighten terminal screws.
Proximate solderless
terminals
Visual check
Proper intervals
Correct.
Loose connectors
Visual check
Not loose
Retighten connector fixing screws.
Dirt on protection sheet
Visual check
Not outstanding
Replace with new one.
Foreign material
attachment
Visual check
No foreign matter sticking
Remove, clean.
Installation status of GOT
2
Criterion
For the model names of the protection sheet or the replacement procedure, refer to the following.
8.4 Protective Sheet
17.2 Periodic Inspection
 Yearly or half-yearly inspection items
The following inspection should also be performed when equipment has been moved or modified or the wiring
changed.
No.
Inspection Item
Ambient
temperature
1
Surrounding
environment
Ambient
humidity
Inspection Method
Make measurement with thermometer or
hygrometer.
Measure corrosive gas.
Atmosphere
2
3
4
5
Connection
status
Battery
0 to 50
Other portions
0 to 55
10 to 90%RH
For use in control panel, temperature
inside control panel is ambient
temperature.
No corrosive gas
20.4 to 26.4VDC
Change supply power.
Looseness
Move module.
Should be mounted firmly.
Retighten screws.
Foreign
material
attachment
Visual check
No foreign matter sticking
Remove, clean.
Loose
terminal
screws
Retighten screws with screwdriver.
Not loose
Retighten terminal screws.
Proximate
solderless
terminals
Visual check
Proper intervals
Correct.
Loose
connectors
Visual check
Not loose
Retighten connector fixing screws.
No alarm displayed
Replace with new battery when the
current battery has reached the
specified life span, even if battery
voltage is not displayed.
Check GOT internal battery voltage
status in [Time Setting & Display] of the
Utility.
(
12.1.1 Time setting and display
functions)
17 - 2
Display section
Action
24VDC Measure voltage across
terminals.
Power supply voltage check
Mounting
status
Criterion
17. MAINTENANCE AND INSPECTION
17.1 Daily Inspection
17
MAINTENANCE AND
INSPECTION
17.3 Cleaning Method
Use the GOT always in a clean condition.
To clean the GOT, wipe the dirty part with a soft cloth using neutral detergent.
For the display operation of the [Clean] screen, refer to the following.
15. CLEANING DISPLAY SECTION (CLEAN)
18
APPENDICES
TROUBLESHOOTING
Clean
POINT
Precautions for cleaning
Do not use chemicals such as thinner, organic solvents and strong acids, since they may cause the protective
sheet to be deformed or the dissolvable paint on the surface to peel off.
In addition, do not use spray solvents since they may cause the electrical failure of the GOT and peripheral
devices.
17. MAINTENANCE AND INSPECTION
17.3 Cleaning Method
17 - 3
17.4 Battery Voltage Low Detection and Battery
Replacement
 Low battery voltage detection and replacement
Battery contains the data for notifying the maintenance timing and current time.
It is recommended that you replace battery periodically.
For the replacement procedure, refer to the following.
8.3 Battery
The battery voltage low detection can be confirmed by the utility screen and system alarm.
For details of the battery status display by the utility screen, refer to the following.
11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)
By using system alarm, the message that notifies the battery voltage has decreased can be displayed at the battery
voltage low on the screen of the GOT.
To display the message in the system alarm, set [Battery alarm display] to on.
11.1.1 Function of Display
System alarm
500 Warning! Built-in battery voltage is low.
For details of the system alarm display, refer to the following.
GT Designer3 Version1 Screen Design Manual (Fundamentals)
POINT
Battery replacement timing
When detecting voltage low, replace the battery immediately.
Data can be saved for about one month after the battery voltage low detection and cannot be saved after that.
If it exceeds a month from the voltage low detection to battery replacement, the clock data or D-drive (Internal
SRAM) data may become indefinite.
Adjust the clock and format the D drive (Internal SRAM).
17 - 4
17. MAINTENANCE AND INSPECTION
17.4 Battery Voltage Low Detection and Battery Replacement
Example of alarm output to external device (lamp, buzzer, etc.)
The following describes an example of outputting the battery voltage low signal from a FX series PLC to an
external device with system information.
Condition: The Write Device is "D20" and all data is used (the button is clicked on the setting screen of drawing
software) for the system information assignment.
D36 b12:
Battery voltage low (System Signal 2-2)
Turned on upon a battery voltage drop.
Used as shown below in the sequence program.
RUN monitor
M8000
MOV D36 K4M20
Y***
Output to external device of PLC
Activated the output upon battery
voltage low detection.
APPENDICES
Battery voltage low
M32
"*" indicates the output number at which the external device is connected.
For details of system information, refer to the following.
GT Designer3 Version1 Screen Design Manual (Fundamentals)
17. MAINTENANCE AND INSPECTION
17.4 Battery Voltage Low Detection and Battery Replacement
18
TROUBLESHOOTING
HINT
MAINTENANCE AND
INSPECTION
17
17 - 5
 Handling of Batteries and Devices with Built-in Batteries in EU Member States
This section describes the precautions for disposing of waste batteries in EU member states and exporting batteries
and/or devices with built-in batteries to EU member states.
(1) Disposal precautions
In EU member states, there is a separate collection system for waste batteries. Dispose of batteries properly at
the local community waste collection/recycling center.
The following symbol is printed on the batteries and packaging of batteries and devices with built-in batteries
used for Mitsubishi Graphic Operation Terminal (GOT).
Symbol
POINT
This symbol is for EU member states only.
The symbol is specified in the new EU Battery Directive (2006/66/EC) Article 20 "Information for end-users" and
Annex II.
The symbol indicates that batteries need to be disposed of separately from other wastes.
(2) Exportation precautions
The new EU Battery Directive (2006/66/EC) requires the following when marketing or exporting batteries and/or
devices with built-in batteries to EU member states.
• To print the symbol on batteries, devices, or their packaging
• To explain the symbol in the manuals of the products
(a) Labeling
To market or export batteries and/or devices with built-in batteries, which have no symbol, to EU member
states on September 26, 2008 or later, print the symbol shown in (1) on the GOT or their packaging.
(b) Explaining the symbol in the manuals
To export devices incorporating Mitsubishi Graphic Operation Terminal to EU member states on September
26, 2008 or later, provide the latest manuals that include the explanation of the symbol.
If no Mitsubishi manuals or any old manuals without the explanation of the symbol are provided, separately
attach an explanatory note regarding the symbol to each manual of the devices.
POINT
The requirements apply to batteries and/or devices with built-in batteries manufactured before the enforcement
date of the new EU Battery Directive (2006/66/EC).
17 - 6
17. MAINTENANCE AND INSPECTION
17.4 Battery Voltage Low Detection and Battery Replacement
The usable duration of backlight can be extended by setting to "Screen saving backlight off" in the utility of GOT
(GOT set up). For details, refer to the following.
11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)
17.5.1
Backlight shutoff detection and external alarm
When the GOT detects a backlight shutoff, the system information set with drawing software is turned on.
You can issue a backlight shutoff of the GOT from the PLC to external devices (such as the lamp or buzzer), using
system information.
To avoid any screen touch operation by the user who misunderstands it is in screen saving mode, install an external
alarm and interlock the loads that would cause danger.
For details of the system information, refer to the following.
GT Designer3 Version1 Screen Design Manual (Fundamentals)
HINT
Example of alarm output to external device (lamp, buzzer, etc.)
The following provides an example of outputting the backlight shutoff detection signal from a FX Series PLC to an
external device, using system information.
Condition: The Write Device is "D20" and all data is used (the button is clicked on the setting screen of drawing
software) for the system information assignment.
D36 b14:
Backlight shutoff detection (System Signal 2-2)
Turned on upon a backlight shutoff.
Used as shown below in the sequence program.
RUN monitor
M8000
MOV D36 K4M20
Backlight shutoff detection
M34
Y***
Output to external device of PLC
Activated the output upon backlight
shutoff detection.
"*" indicates the output number at which the external device is connected.
POINT
Precautions for the backlight shutoff status
In the backlight shutoff status, the touch key operates.
Early replacement of backlight is recommended.
17. MAINTENANCE AND INSPECTION
17.5 Backlight Shutoff Detection
17 - 7
18
TROUBLESHOOTING
(1) Life of backlight
APPENDICES
The backlight is built into GOT for the liquid crystal display.
When GOT detects backlight shutoff, the POWER LED blinks green/orange alternately.
The brightness of the backlight decreases with the lapse of usage period. When backlight shutoff is detected or the
display becomes unclear, replace the backlight. (GT14 requires LED replacement.)
For replacement of the backlight, contact your nearest sales office or FA Center.
MAINTENANCE AND
INSPECTION
17
17.5 Backlight Shutoff Detection
17 - 8
17. MAINTENANCE AND INSPECTION
17.5 Backlight Shutoff Detection
18. TROUBLESHOOTING
MAINTENANCE AND
INSPECTION
17
This chapter explains the GOT restoration sheet and the error message/system alarm list.
18.1 GOT Restoration Sheet
This section provides restoration methods for the case the GOT does not operate normally, which are listed in check
sheets.
The following explains how to use each sheet.
(1) When the GOT does not operate or malfunctions (GOT status check sheet)
TROUBLESHOOTING
18
(2) When the wiring status needs to be improved (GOT installation status check sheet)
When the noise caused by the GOT wiring status is considered to have caused the malfunction, etc. based on
the check result of (1) above, take corrective action for wiring using GOT installation status check sheet.
When the GOT is restored, see the status for a while.
(3) When corrective action other than (1) and (2) above is required (System configuration check sheet)
If malfunction etc. occurs even after checking with (1) and (2) above, please contact your local Mitsubishi
(Electric System) Service after filling out System configuration check sheet with details about your system.
When sending a troubled product, attach the GOT restoration sheets (GOT status check sheet, GOT installation
status check sheet, System configuration check sheet) checked in this section.
Please keep copies of the restoration sheets.
18. TROUBLESHOOTING
18.1 GOT Restoration Sheet
18 - 1
APPENDICES
When the GOT does not operate or malfunctions, identify the cause of the malfunction etc. with GOT status
check sheet and take corrective action.
When the GOT is restored, see the status for a while.
 GOT status check sheet
Check the GOT starting from (1) GOT status.
Proceed as instructed by "Action".
(1) GOT status
Phenomenon
Cause/status
Action
(a) Frequency when the GOT does not operate, an error occurs on the screen, etc.
Occurs always.
Occurs sometimes.
Occurrence frequency:
(
Example: Once a month
)
Proceed to (1)-(b).
(b) Checking of the displayed error code (system alarm)
Can be checked.
Error code (system alarm):
(
)
Example: 460 Communication unit error
Take the action for the error code (system
alarm) or error message checked.
If the status does not change after the action
is taken, proceed to (1)-(c).
Proceed to (1)-(c).
Cannot be checked.
(c) POWER LED
Lit in green
The power is supplied normally.
Proceed to (1)-(d).
Lit in orange
Screen saving is being performed.
The read device of the system information may
have been turned ON when the device was set,
and the screen was switched to the forced screen
saving status.
Check the setting of the read device.
When no problem is found in the setting,
proceed to (1)-(d).
Blinks in green/orange
The backlight has run out.
Replace the backlight.
If the GOT is not restored, proceed to (1)(d).
The power is not supplied.
Not lit
When the power is supplied, the GOT hardware
may be faulty.
Check if the power is supplied. If the GOT is
not restored, proceed to (5) Troubled
product investigation.
(d) Screen display
The screen is completely
black.
The liquid crystal display or BootOS may be faulty.
Perform the following in order.
1) Reinstalling BootOS
2) Reinstalling standard monitor OS
If the GOT is not restored by 1) and 2),
perform the following.
3) Reinstalling CoreOS and then standard
monitor OS
If the GOT is not restored by the above
operations, proceed to (5) Troubled product
investigation.
The screen is completely
white.
The GOT hardware may be faulty.
Proceed to (5) Troubled product
investigation.
A line is displayed on the
screen.
The GOT hardware may be faulty.
Example: A vertical line is displayed.
Proceed to (5) Troubled product
investigation.
Other faulty displays
The screen freezes.
18 - 2
The screen display is not updated and any
operation is not allowed.
18. TROUBLESHOOTING
18.1 GOT Restoration Sheet
Proceed to (1)-(e).
17
Action
(e) Buzzer sound
Does not sound.
Continues to beep randomly.
Continues to beep in a
particular pattern.
Beeps continuously.
Buzzer sound:
(
)
Example: The rhythm as three beeps, one beep,
and then two beeps is repeated.
Proceed to (2) Status of the GOT when it
freezes.
The read device of the system information may
have turned ON when the device was set, turning
ON the Buzzer output signal.
Check the setting of the read device.
When the Buzzer output signal has no error,
proceed to (2) Status of the GOT when it
freezes.
(2) Status of the GOT when it freezes (screen operation stopped)
Phenomenon
Cause/status
MAINTENANCE AND
INSPECTION
Cause/status
18
TROUBLESHOOTING
Phenomenon
Action
Enabled
Error code (system alarm):
(
)
Example: 460 Communication unit error
When the system alarm display function can
be used, take the action for the error code
(system alarm) displayed.
If the action cannot be taken, proceed to (2)(b).
Disabled
The system alarm display function cannot be
used.
Proceed to (2)-(c).
(b) Executing of I/O check from the GOT utility
Communication error
Display details:
(
)
Example: A message indicating the cause may be
a connection error was displayed.
Proceed to (2)-(c).
No error
The hardware such as a communication interface
has no error.
Proceed to (3) Status of the PLC CPU.
(c) Objects not displayed on the monitor screen
Found
Not found
Details:
(
)
Example: The numerical display object is not
displayed.
Proceed to (3) Status of the PLC CPU.
(3) Status of the PLC CPU
Phenomenon
Cause/status
Action
(a) PLC failure
Occurs always.
An error such as CONTROL-BUS. ERROR or SP.
UNIT LAY. ERROR may have occurred.
Error code (system alarm):
(
)
Example: 1204 CPU H/W fault
Proceed to the following.
18.1
The PLC CPU may be influenced by noise or the
hardware may be faulty.
Occurs sometimes.
Operates normally.
Occurrence frequency:
(
Example: Once a month
)
Error code (system alarm):
(
Example: 1204 CPU H/W fault
)
Proceed to (4) GOT restoration procedure.
-
18. TROUBLESHOOTING
18.1 GOT Restoration Sheet
18 - 3
APPENDICES
(a) Switching to the utility
(4) GOT restoration procedure
Follow the procedures below starting from (a) and in order to check if the GOT is restored.
If the GOT is not restored, proceed to the next item.
Check item
Cause
Action
(a) Press the GOT reset switch.
Restored
Not restored (Proceed to (b).)
(b) Power the GOT ON/OFF.*1
Restored
Not restored (Proceed to (c).)
(c) Reset or power ON/OFF the PLC
CPU.
The GOT may have malfunctioned
temporarily due to noise.
Take the action of (4)-(h).
The cable connection may be faulty.
Securely connect the cable.
If an error occurs again, proceed to (5)
Troubled product investigation.
Data may have been destroyed by an
action such as powering the GOT OFF
during the installation of project data or
OS.
Do not power the GOT OFF while
transferring data.
If an error occurs again, proceed to (5)
Troubled product investigation.
The GOT may have malfunctioned
temporarily due to noise.
Take the action with referring to GOT
installation status check sheet.
Restored
Not restored (Proceed to (d).)
(d) Power the GOT and PLC CPU ON/
OFF simultaneously.
Restored
Not restored (Proceed to (e).)
(e) Connect the cable again.
Restored
Not restored (Proceed to (f).)
(f) Reinstall the project data.
Restored
Not restored (Proceed to (g).)
(g) Reinstall the OS.
Restored
Not restored (Proceed to (h).)
(h) Take the action described in the
"Action" column.
Restored
Not restored (Proceed to (i).)
(i) The GOT is not restored even by
performing (a) to (h).
*1
When powering the GOT ON again (OFF
-
Proceed to (5) Troubled product
investigation.
ON), power OFF the PLC before that.
(5) Troubled product investigation
When malfunction of the GOT is not improved, please contact your local Mitsubishi (Electric System) Service.
Depending on the problem details, we may ask you to return the troubled product to us.
In that case, please attach the GOT status check sheet, GOT installation status check sheet, and the system
configuration check sheet filled out with details of your system.
18 - 4
18. TROUBLESHOOTING
18.1 GOT Restoration Sheet
Check the current installation status of the GOT you are using against the GOT installation status described in the
upper column of items (1) to (7).
When the measure described in the lower column is needed, take the measure for the current status.
When the measure is taken, check the result, "Effective" or "Ineffective".
(1) Panel inside wiring
TROUBLESHOOTING
18
NFB
The power line connected to the power or
servo amplifier and the communication
cable are mixed in the duct.
Current status
MC
RA
RA
Mixed
Not mixed
APPENDICES
MC
NFB
Wiring the power line and communication
cable in the panel without mixing them in
the duct can reduce the influence of noise.
Measure for the
cables mixed
MC
MC
RA
RA
Effective
Ineffective
(2) Panel outside wiring
Power line
The power line and communication cable
are installed together.
Current status
Installed together
Not installed
together
Communication cable
Fig. A
Power line
Measure for
the cables
installed
together
Communication cable
Power
line
Fig. B
MAINTENANCE AND
INSPECTION
17
 GOT installation status check sheet
Wiring
duct
Separator
100mm or more
Signal
line
Power
line
Communication
cable
Leading the power line and
communication cable outside the panel
at separate places can make the
communication cable less influenced by
noise from the power line. Installing the
communication cable apart from the
power line or using a separator (made of
metal) in the duct as shown in Fig. B can
make the communication cable less
influenced by noise.
18. TROUBLESHOOTING
18.1 GOT Restoration Sheet
Effective
Ineffective
18 - 5
(3) Wiring of GOT's FG cable and power line
GOT
The FG cable and power line of the GOT
are installed together.
Current status
FG
Installed together
Not installed
together
Power for the power equipment
GOT
Measure for the
cables installed
together
Separating the FG cable and power line of
the GOT in wiring reduces the influence of
noise.
FG
Effective
Ineffective
Power for the power equipment
(4) Surge measures
A surge suppressor is used for the wiring of
the load such as MCCB, electromagnetic
contactor, relay, solenoid valve, or
induction motor.
PLC
C
Current status
Output
R
L
AC
Used
(When a surge suppressor is used, fill out
the entry area below with the surge
suppressor model name and the name of
the equipment for which the surge
suppressor is used.)
Not used
PLC
Measure for the
equipment without
a surge suppressor
used
C
Output
R
L
Attaching the surge suppressor on the
cable close to the load can reduce the
influence of surge on the GOT.
AC
The surge suppressor must be
attached close to the load
Entry area
Model name of the surge suppressor
18 - 6
18. TROUBLESHOOTING
18.1 GOT Restoration Sheet
Equipment name
Effective
Ineffective
CN1A CN1B
CN2 CN3
Current status
PLC
Connection cable
FG
The FG cables of the control
equipment (such as PLC) and the
power equipment (such as servo
amplifier) are connected as shown
by "a".
LG
FG
GOT
a
FG
Panel grounding
Connected
Not
connected
Panel grounding
Servo
CN1A CN1B
18
TROUBLESHOOTING
Servo
MAINTENANCE AND
INSPECTION
17
(5) Grounding status
PLC
Connection cable
FG
APPENDICES
CN2 CN3
LG
FG
GOT
Fig. A
FG
Terminal block
Panel
grounding
Panel grounding
Grounding for
power system
Measure for
the FG cables
connected
Servo
Terminal block
Grounding for
power system
PLC
Perform independent grounding at
two places as shown in Fig. A.
Independent grounding can reduce
the influence of noise.
If independent grounding is not
allowed, be sure to perform shared
grounding as shown in Fig. B.
Effective
Ineffective
Connection cable
CN1A CN1B
FG
CN2 CN3
Fig. B
FG
LG
GOT
Panel grounding
FG
Panel grounding
18. TROUBLESHOOTING
18.1 GOT Restoration Sheet
18 - 7
(6) Grounding status of the panel on which the GOT is installed
Connection
cable
GOT
Ground cable led from the
panel having the control
equipment
Current status
FG
A single ground cable is led from the
panel having the control equipment
such as PLC to the panel having the
GOT.
Led
Not led
Connection
cable
GOT
Fig. A
FG
Ground cable
Use a short and
thick wire as
possible.
Ground to
the panel.
Connection
cable
Connecting the ground cable to the
panel having the GOT as shown in
Fig. A to reduce the potential
difference may prevent the
malfunction.
When wiring as shown in Fig. A is
difficult, perform wiring as shown in
Fig.B.
Effective
Ineffective
GOT
Fig. B
Ground cable
FG
Ground to
the panel.
Measure for the
ground cable
led
Connection
cable
GOT
Fig. C
FG
Ferrite core
Ground cable
Use a short and
thick wire as
possible.
Ground to
the panel.
Connection
cable
GOT
Fig. D
Ground cable
FG
Ferrite core
Ground to
the panel.
18 - 8
18. TROUBLESHOOTING
18.1 GOT Restoration Sheet
Attaching the ferrite core to the ground
cable connected to the panel having
the GOT as shown in Fig. C reduces
the influence of noise.
When wiring as shown in Fig. C is
difficult, perform wiring as shown in
Fig. D.
Effective
Ineffective
Current status
PLC
GOT
I/O power
I/O equipment
Main circuit power
The power from the same system is used
for the GOT, I/O equipment (such as
relay), and power equipment (such as
servo amplifier).
Used
Not Not used
18
Power
equipment
Connecting an isolation transformer as
well as separating the wiring of the GOT
power from that of the power of the I/O
equipment and power equipment reduces
the influence of noise.
Effective
Ineffective
APPENDICES
Measure for the
equipment for which
the power from the
same system is used
Isolation transformer
Main power
PLC power
AC200V
PLC
GOT
I/O power
I/O
Main circuit power equipment
Power
equipment
TROUBLESHOOTING
Main power
PLC power
AC200V
MAINTENANCE AND
INSPECTION
17
(7) Power supply system
18. TROUBLESHOOTING
18.1 GOT Restoration Sheet
18 - 9
 System configuration check sheet
Fill in the brackets with the unit/module name.
(1) System configuration of the GOT
(a) GOT main unit
[
]
(b) Communication interface
[
]
(c) Cable between the PLC and GOT
[
]
(d) Cable length
[
m]
(a) Power supply module
[
]
(b) CPU module
[
]
[
]
[
]
[
]
[
]
[
stages]
(2) System configuration of the PLC
(c) Serial communication unit/computer
link module
Used
(d) Network module
Used
Not used
Not used
(e) Interrupt module
Used
Not used
(f) Positioning module
Used
Not used
(g) Number of extension stages
(h) If any other module etc. is used, please describe it.
Entry area for recurrence (when the malfunction occurred after the action is taken)
(3) Describe the operation situation when freezing of the screen or faulty display of the GOT has reoccurred.
18 - 10
18. TROUBLESHOOTING
18.1 GOT Restoration Sheet
This chapter describes the error message and system alarm displayed in the GOT.
As the error code and error message displaying functions when an error occurs at the GOT, controller or network, there
are two kinds: system alarm and advanced system alarm.
For details of the system alarm and advanced system alarm, refer to the following.
MAINTENANCE AND
INSPECTION
17
18.2 Error Message and System Alarm
POINT
Error code and channel No.
• Error codes can also be confirmed in the error code storage area of the system information function.
• The channel No. where an error is occurring can be confirmed with the GOT special register (GS262 to 264).
For details of the system information and GOT special register, refer to the following manual.
TROUBLESHOOTING
18
GT Designer3 Version1 Screen Design Manual (Functions)
18.2.1
APPENDICES
GT Designer3 Version1 Screen Design Manual (Fundamentals)
Error contents display
This section describes the example for displaying error code and error message on GOT.
 Popup-displaying the error code and error message (Advanced alarm popup display
(System alarm))
If an error occurs, the error code and error message can be popup-displayed on the front of the monitor screen.
As alarms are popup-displayed regardless of the screen type, the error occurred will not be overlooked.
A 1254 A 1254
B 348 B 348
04/6/1 13:20 Power module
Pop up generated alarms
regardless of the screen.
 Displaying error code and error message in a list (Advanced system alarm display)
If error has occurred, error code and error message can be displayed on the list set with the screen.
Multiple errors can be displayed, or the history of display can be recorded.
Occurred
04/6/1 10:25
04/6/1 8:05
Message
Temp. error
Fuse error
Restore
11:25
Check
10:45
Create a screen to display alarms, and confirm
the details of the alarms and take measures.
18. TROUBLESHOOTING
18.2 Error Message and System Alarm
18 - 11
 Checking error messages with the utility (Utility)
The error code and error message can be checked with the system alarm display of the utility when the object is not
set.
14.3 System Alarm Display
Error code and reference manual
Error
source
Error code
Channel No.
storage
Description
Reference
destination*1
0 to 99
(Value of D9008)
Error code of CPU (for ACPU)
User's manual of the ACPU connected with GOT
Error code of the following
controllers
Controller
100 to 299
FXCPU*2
Third party PLC
Temperature controller
(OMRON temperature controller
only)
GS263
User's manual of the controller connected with the GOT
Deal with errors according to the error messages.
300 to 399
Error code of the GOT main unit
function
400 to 499
Error code of the GOT
communication function
500 to 699
Error code of the GOT main unit
function
Network
800 to 999
Error code of network
CPU
1000 to 10000
(Value of SD0)
Error code of CPU
(for QCPU, QnACPU)
User's manual of the QCPU and QnACPU connected with
GOT
Motion
controller
10001 to 10999
Error code of Motion controller
(Q173DCPU/Q172DCPU)
User's manual of the Motion controller connected with GOT
CNC C70
11000 to 11999
Error code of CNC (Q173NCCPU)
12000 to 12999
Error code of Robot controller
(Q172DRCPU)
User's manual of the Robot controller connected with GOT
20016 to 20237
Error code of servo amplifier
User's manual of the servo amplifier connected with GOT
GOT*5
Robot
controller
Servo
amplifier*3
GS262*4
18.2 Error Message and System Alarm
GS264
GS263
User's manual of the CNC C70 connected with GOT
*1
For details of GOT special registers (GS262 to 264), refer to the following manual.
*2
The assigned error code for FXCPU is 100 to 109, which displays the status of M8060 to M8069.
(Example) When the error code (100) error occurs, correct the error according to the M8060 description.
The error code displayed on GOT is calculated by changing the error code (Hexadecimal) displayed on the servo amplifier to the
decimal number and adding 20000 to it.
When referring to the manual of servo amplifier by the error code displayed as a GOT system alarm, subtract 20000 from the
GOT error code and change its lower three digits to the hexadecimal number.
(Example: When GOT system alarm is 20144, the error code of servo amplifier becomes 90H.)
Channel No. will not be stored depending on the error code.
For channel No. storage availability for each error code, refer to the following.
GT Designer3 Version1 Screen Design Manual (Fundamentals)
*3
*4
18.2.2 List of error message/system alarm
*5
18 - 12
An alarmed drive cannot be confirmed in the system alarm regarding file access; however, it can be specified by confirming the
file access error signal (b7 to 10) of system signal 2-2.
18. TROUBLESHOOTING
18.2 Error Message and System Alarm
17
List of error message/system alarm
The system alarm detected with GOT is shown below.
Set monitor points too large.
Decrease setting points.
Action
Channel No.
storage
Decrease the number of objects from the displayed screen.
For the number of maximum objects for 1 screen, refer to the following.
18
GT Designer3 Version1 Screen Design Manual (Fundamentals)
304
Set trigger points too large.
Decrease setting points.
The number of objects using Sampling/Cycle during ON/Cycle during
OFF exceeds 100.
Decrease the number of objects.
306
No project data.
Download screen data.
The project data is not downloaded or the screen data is not sufficient.
Download the project data or screen data.
307
Monitor device not set
The monitor device of the object is not set.
Set the monitor device of the object.
308
No comment data.
Download comment.
The comment file does not exist.
Create the comment file and download to GOT.
309
Device reading error.
Correct device.
The error occurred when reading a continuous device.
Correct the device.
310
Project data does not exist or out
of range.
311
No. of alarm has exceeded
upper limit.
Delete restored alarm.
The number of alarm histories that can be observed by the alarm history
display function has exceeded the maximum points.
Delete the restored history to decrease the number of alarm histories.
312
No. of sampling has exceeded
upper limit.
Delete collected data.
The collection frequency exceeded the upper limit when "Store Memory"
and "Accumulate/Average" were set in the scatter graph.
• Approve "Clear trigger" setup in the scatter graph.
• Set the "Operation at frequency over time" to "Initialize and Continue"
in scatter graph.
315
Device writing error.
Correct device.
Error occurred while writing in the device.
Correct the device.
316
Cannot display or input operation
value.
Review expression.
In indirect specification of comment/parts number, the data operation
result exceeded the range in which device type can be expressed.
Review the data operational expression, in order not exceeding the range
in which the device type can be expressed.
317
Too high frequency of data
collection.
Review conditions.
Data of an object, to which [Collect data only when trigger conditions are
satisfied] is set, are collected too frequently, or the number of objects has
exceeded the number of objects collectable simultaneously.
Set a longer cycle for trigger occurrence to each object.
Make the settings so that 257 or more display triggers of objects, to which
[Collect data only when trigger conditions are satisfied] is set, do not
occur simultaneously.
320
Specified object does not exist or
out of range.
The part file does not exist.
Create the part file and download to GOT.
322
Dedicated device is out of range.
Confirm device range.
The monitored device No. is out of the permissible area of the targeted
PLC CPU.
Set the device within the range that can be monitored by the monitored
PLC CPU and parameter settings.
TROUBLESHOOTING
303
Error message
APPENDICES
Error
code
• Specified base screen / window screen does not exist in the project
data.
• Specified base screen / window screen is out of the permissible area.
Specify the existing base screen / window screen.
18. TROUBLESHOOTING
18.2 Error Message and System Alarm
MAINTENANCE AND
INSPECTION
18.2.2
18 - 13
Error
code
Error message
330
Insufficient memory media
capacity.
Confirm M-card capacity.
Available memory of the SD card is insufficient.
Confirm the available memory of the SD card.
The available memory can be confirmed by system information screen,
which is described in GT Designer3 Version1 Screen Design Manual
(Fundamentals).
331
Memory card not installed or
MCARD switched OFF
The SD card is not installed or in the drive access switch is OFF in drive.
• Install the SD card in the specified drive.
• Turn ON the access switch.
332 Memory media is not formatted.
SD card is not formatted or formatted incorrectly.
Format the SD card.
333
Unable to overwrite. Memory
card is write-protected.
SD card is write-protected.
Cancel the write-protection of SD card.
334
Memory media error.
Replace memory media.
SD card is faulty.
Replace the SD card.
File output failed.
Confirm output file path.
Either of the following folder or file with the name same as the file to be
created exists in the storage destination SD card or USB memory.
• Folder storing data
• Write-protect file
Delete the above folder or file, or change the name of the file to be
created.
337
18 - 14
Action
340 Printer error or power failure.
Printer is faulty or the printer power supply has not been turned on.
• 1. Confirm the printer.
• 2. Turn on the power supply of the printer.
341 Printer error
Printer is faulty or the printer power supply has not been turned on.
• 1. Confirm the printer.
• 2. Turn on the power supply of the printer.
345
BCD/BIN conversion error
Correct data
Any value that cannot be converted to a BCD/BIN value is being
displayed/input.
• Change the device data to be displayed to the BCD value.
• Correct the input value to the 4 digits integer.
351
Recipe file error.
Confirm content of recipe file.
The contents of the recipe file are not normal.
• Confirm the contents of the recipe files in the SD card or USB memory.
• Reboot the GOT after deleting the recipe file in the SD card or USB
memory (format).
352
Recipe file make error.
Reboot GOT after inserting
memory card.
Failed to generate recipe file.
Reboot the GOT after installing the SD card or USB memory.
353
Unable to write Recipe file.
Confirm memory card is
inserted.
Failed to write in the recipe file.
• Confirm the write-protection of the SD card or USB memory.
• Confirm the contents of the SD card or USB memory.
• Do not pull out the SD card or USB memory while recipe is operating.
354 Recipe file write error
Error occurred while writing in the recipe file.
Do not pull out the SD card or USB memory while recipe is operating.
355 Recipe file read error
Error occurred while reading in the recipe file.
• Do not pull out the SD card or USB memory while recipe is operating.
• Confirm the contents (device value) of the recipe file in the SD card or
USB memory.
18. TROUBLESHOOTING
18.2 Error Message and System Alarm
Channel No.
storage
File system error occurred in
PLC.
Confirm file register.
Error occurred in the specified file register when executing the recipe
function by specifying the file register name.
• Execute the recipe function again after confirming the file register
name.
• Execute the recipe function again after formatting the PC memory in
the specified PLC CPU drive with GX Developer.
Error in specified PLC drive
Confirm PLC drive.
When executing the recipe function specifying the file register name,
error occurred in PLC CPU drive.
• Execute the recipe function again after confirming the specified PLC
CPU drive.
• Execute the recipe function again after formatting the PC memory in
the specified PLC CPU drive with GX Developer.
358
PLC file access failure.
Confirm PLC drive.
When the recipe function is executed specifying the file register name,
PLC CPU file register could not be accessed.
• Execute the recipe function again after confirming the specified PLC
CPU drive / file register name. (When you specify drive 0, execute the
recipe function again after changing to other drives.)
• Confirm whether the SD card or USB memory are write-protected, and
execute the recipe function again.
359
Processing from another
peripheral device.
Execute it after.
When the recipe function is executed specifying the file register name,
other peripherals carry out the process to the file register.
Wait until the processing of other peripherals end, and execute the recipe
function again.
360
0 divisor division error.
Confirm operation expression.
Zero division occurred by the data operational expression.
Review the data operational expression so that the divisor should not
become 0.
361
Specified device No. is out of
range.
The entered file number is out of range.
Check the entered file number, and enter a valid value (1 to 9999).
362
Invalid device value in time
action setting
When controllers are controlled with the GOT's time action function, the
set No. is our of range, or the set device values regarding the operation
settings are out of range or invalid.
Set valid values.
370
Upper and lower limit value error.
Confirm value setting.
The setting of lower/upper limit value is [Upper limit < Lower limit].
Correct the setting so as to be "Upper limit &inequalityLEM Lower limit".
380
Insufficient USB drive capacity.
Confirm the drive capacity.
Available memory of the USB memory is insufficient.
Confirm the available memory of the USB memory, and increase the
memory if it is low.
381
USB drive is not installed or in a
removable state.
If the USB memory is not installed, install it.
If the USB memory is ready to be removed, install it again.
382
USB drive is not formatted.
Memory card is not formatted or in a format not conformed by a GOT.
Reformat the USB memory.
383
Unable to overwrite. USB drive is
write-protected.
USB memory is write-protected.
Cancel the write-protection of USB memory.
384
USB drive error. Replace USB
drive.
USB memory is faulty.
Replace the USB memory.
356
357
18. TROUBLESHOOTING
18.2 Error Message and System Alarm
Channel No.
storage
17
MAINTENANCE AND
INSPECTION
Action
18
TROUBLESHOOTING
Error message
APPENDICES
Error
code
18 - 15
Error
code
Error message
Action
Communication timeout.
Confirm communication pathway
or modules.
The time-out error occurred during communicating.
• Confirm the cable omission and status of the PLC.
Channel No. is not displayed in error code or error message in the
case an error occurs when using the multi-channel function.
Refer to the following manual to identify the channel No. in error.
• This error may occur when the load of the PLC CPU becomes heavier
when accessing other stations. In such a case, transfer the data of the
other stations to the host station PLC CPU and monitor them at the
host.
• Put COM instruction when the PLC scanning is long.
403
SIO status error.
Confirm communication pathway
or modules.
Either of the overrun error, parity bit error or flaming error was generated
when the RS-422 / RS-232 communication was received.
Confirm the cable omission, status of the PLC.and the transmission
speed of the computer link.
Channel No. is not displayed in error code or error message in the case
an error occurs when using the multi-channel function.
406
Specified station access is out of
range.
Confirm station no.
• Station numbers other than master/local station are specified at the
CC-Link connection (via G4).
• A PLC CPU other than QCPU is accessed.
• Confirm the station number of the project data.
407
Accessed other network.
Change network setting.
• When monitoring other networks
Reconfigure the [Routing Information Setting] of GT Designer3 or the
[Routing parameters] of GX Developer.
410
Cannot perform operation
because of PLC run mode.
stop the PLC.
The operation, which could not be performed during RUN of PLC CPU,
was performed.
Stop the PLC CPU.
411
Memory cassette is
writeprotected.
Check the memory cassette.
The memory cassette installed in the PLC CPU is EPROM or E2PROM,
and it is in a protected status.
Confirm the memory cassette installed in PLC CPU.
402
Cannot read/write device
412 protected by keyword.
Remove keyword.
The key word is set in PLC CPU.
Cancel the key word.
420 E71 specification is ASCII.
[ASCII code] is selected in [Ethernet operations] of the PLC side setting.
Select [Binary code].
421
E71 is set as read-only.
Clear setting.
Not communicating between
422 CPU and E71. Confirm CPU
error.
18 - 16
The Ethernet module on the PLC side is set in read-only.
Set the Ethernet module on the PLC side to write-enabled.
PLC CPU error. Communication between PLC CPU and the PLC side
Ethernet module impossible.
Confirm whether there is error in PLC CPU by GX Developer etc.
(Confirm buffer memory)
18. TROUBLESHOOTING
18.2 Error Message and System Alarm
Channel No.
storage
Insufficient network table
information. Add station no.
The station number set in the project data and the station number set in
the switching station No. device do not exist in the Ethernet setting of GT
Designer3.
• Add the station number set in the project data to the Ethernet setting of
GT Designer3.
• When using the station No. switching function, check the data of the
switching station No. device.
When the station number specified in the switching station No. device
is not set in the Ethernet setting, add the station number to the
Ethernet setting.
When the station number does not exist in the system, change the data
of the switching station No. device.
(Set the station number so that it becomes the same as the station
number of the PLC side Ethernet module set in the parameter setting
of GX Developer.)
424
Same sta. on GOT & project
data. Review communication
parameter.
The station number set in the GOT's utility is the same as the station
number set in the Ethernet setting of GT Designer3 or GT Designer2 (the
station number of the PLC side Ethernet module) or in the project data.
Check the following contents so that the multiple station numbers should
not be the same.
• Check the GOT's station number in the GOT's utility.
• Check the station number set in the project data.
• Check the station number set in the Ethernet setting.
(Set the station number so that it becomes the same as the station
number of the PLC side Ethernet module set in the parameter setting
of GX Developer.)
• When using the station No. switching function, check the data of the
switching station No. device.
425
A duplicate IP address has been
detected. Confirm the setting.
The IP address of the GOT is the same as that of the controller.
Change the IP address of the GOT or the controller.
448
PLC cannot handle as
requested. Correct devices.
A device outside the range of PLC file registers and the buffer memory
was specified.
Correct the monitor device by setting file register of the PLC CPU.
449
Dedicated device is out of range.
Confirm device range.
Set the address for the special function module in the GOT monitor
available range. Set the device in the GOT monitor available range.
450
Path has changed or timeout
occurred in redundant system.
The path has been switched or timeout occurred in the redundant system.
• Check the PLC CPU to know if the path has been switched.
• Check the cable connection status and the PLC CPU status.
• This error may occur when the load of the PLC CPU becomes heavier
when accessing other stations. In such a case, transfer the data of the
other stations to the host station PLC CPU and monitor them at the
host.
• Perform one of the following operations if the PLC scanning time is
long: COM instruction/Extension of END processing/Setting of the
number of processing times for general data/Data update batch
processing.
451
Q redundant system settings and
current config. do not match.
Change the Q redundant setting in accordance with the actual Q
redundant CPU system.
460
Communication unit error
423
Channel No.
storage
18
• Reset the power of the GOT.
• Replace the unit.
18. TROUBLESHOOTING
18.2 Error Message and System Alarm
17
MAINTENANCE AND
INSPECTION
Action
TROUBLESHOOTING
Error message
APPENDICES
Error
code
18 - 17
Error
code
Action
480
Communication channel not set.
Set channel number on Utility.
Channel (CH.No.1 to 2) to communicate with a controller is not set.
• After setting the Communication Settings on the GT Designer3,
download it to the GOT.
• Change the channel assignment in the Communication Setting on the
utility.
*1
486
Communication unit not
corresponded to set
communication driver.
The communication driver set in the Communication Setting and the
communication built into the GOT do not match.
• Check whether the communication driver set in the Communication
Setting is correct.
*1
487
Please turn on the PLC and the
GOT again.
Turn the power of the PLC and GOT on again.
489
Inactive channel has been
selected at Communication
Settings.
Inactive channel No. has been set in the project data.
• Check whether any unnecessary channel No. has been set in the
project data.
• Check whether channel Nos. set in the project data are set in the
Communication Settings.
500
Warning! Built-in battery voltage
is low.
The voltage of the GOT built-in battery is decreased.
Replace the GOT built-in battery.
510 Clock data input out of range
The value that is input as clock data is out of the input enabled range.
In this case, the input value is not accepted.
Confirm the input range of the value to be input as clock data, and input
the proper value again.
520 Insufficient Flash ROM capacity
The capacity for the buffering area is insufficient in the build in flash
memory
• Confirm whether there are no mistakes in specified buffering area size.
521
Insufficient user memory (RAM)
capacity
The capacity for the buffering area is insufficient in the user memory
(RAM)
• Confirm whether there are no mistakes in specified buffering area size.
522
Unnecessary file deleted to
create new file.
The old file of different contents has been deleted and a new file has been
created.
Note that the old file is deleted and the new file is created if the file of the
same name with different contents exists when creating files.
524
Device writing error.
Correct device.
Error occurred while writing in the device.
Correct the device.
525
Unable to read/write alarm log
files under different projects.
Unable to read the alarm log file saved by the different project.
Confirm where to store the alarm log file and alarm log file.
526 File conversion failed.
The file specified for the file conversion does not exist.
Check the settings for specifying a file to be converted.
528
Error in SRAM. Failed to write
data.
The error may be caused by a failure in the GOT main unit. Please
consult your local Mitsubishi (Electric System) Service center or
representative.
529
Data error in SRAM.
Check the battery life.
Error in SRAM data due to battery voltage low, etc.
Confirm the battery status.
530
Improper monitor device.
Confirm monitor channel.
The channel of the specified monitor target does not exist or the channel
is not the monitor target.
Confirm the monitor target channel of the screen data.
535 Cannot open image file.
536
18 - 18
Channel No.
storage
Error message
Image file error or invalid file
format.
Confirm whether any file exists in the SD card or USB memory.
• Confirm whether image files in the SD card or USB memory are
normal.
• Confirm whether any image file of invalid format is stored.
18. TROUBLESHOOTING
18.2 Error Message and System Alarm
*1
Error occurred while executing the auto repeat function of the touch
switch object.
Confirm the following.
• Confirm that the other system error has not occurred during auto
repeat.
• Confirm that any error information is not stored in the system
information/GS during auto repeat.
570
Recipe device points too large.
The number of the set points of the recipe device exceeds the specified
range.
Put the number of the set points of the recipe device within the specified
range.
571
Capacity shortage of user
memory (RAM)
There is no empty area/space in D drive.
Format the D drive in the memory to secure free area.
581 Abnormal Advanced recipe file
582
Cannot generate Advanced
recipe file.
583
Unable to save device value to
Advanced recipe file.
Unable to save device value to advanced recipe file.
• Confirm the write-protection of the SD card or USB memory.
• Confirm whether the attribute of saving file is for reading only.
584 Advance recipe file save error
An error has occurred during the advanced recipe file writing.
Do not pull out the SD card or USB memory while the Advanced Recipe
is operating.
585 Advanced recipe file upload error
An error has occurred during the advanced recipe file reading.
Do not pull out the SD card or USB memory while the Advanced Recipe
is operating.
586
Specified Advanced recipe
number does not exist.
The advanced recipe of non-existing number is about to be executed.
Execute advanced recipe of existing number.
587
Specified record number does
not exist.
The advanced record of non-existing number is about to be executed.
Execute record of existing number.
588
Cannot save recipe data to read
only record.
Saving recipe is about to be executed to the record of which recipe device
value cannot be edited.
Make the recipe device value of the record editable with Advanced
Recipe Setting of GT Designer3 or specify the record of which recipe
device value can be edited.
589
Recipe device save error. Recipe
file does not exist.
Saving recipe is about to be executed to the advanced recipe setting that
is set for not using file.
Specify the advanced recipe setting that uses file.
590
Recipe device upload error.
Recipe device value does not
exist.
Loading recipe is about to be executed to the record of which recipe
device value is not set.
Specify the record of which recipe device value is set.
591
Advanced Recipe error. Check
recipe data.
The advanced recipe setting is not correct.
Confirm the advanced recipe setting of the project data and download it
to the GOT again.
Logging file error.
When collecting data again, delete logging files and management files.
18. TROUBLESHOOTING
18.2 Error Message and System Alarm
17
18
Advanced Recipe cannot be executed for advanced recipe file with
incorrect contents. Delete the advanced recipe file from the SD card or
USB memory.
Cannot generate advanced recipe file. Confirm the following and execute
recipe processing again.
• Confirm whether the SD card or USB memory is installed.
• Confirm whether the SD card access switch of the GOT is ON.
• Confirm the available memory of the SD card or USB memory.
595 Logging file error.
Channel No.
storage
MAINTENANCE AND
INSPECTION
Auto repeat error. Confirm
system information.
Action
TROUBLESHOOTING
540
Error message
APPENDICES
Error
code
18 - 19
Error
code
596
Error message
Action
Logging setting does not exist or
setting value error.
The logging setting specified in the historical trend graph setting does not
exist.
Review the historical trend graph setting and specify a logging setting that
exists.
605 USB device I/F error
611
Improper job files.
Confirm job setting.
612
Cannot access Logging Files
Check the memory card
The contents for job files are unmatched with the settings for job files.
Check if there are mistakes in the settings on the setting screen.
• Insert a SD card or USB memory.
• Turn on the SD card access switch.
• If the SD card or USB memory have unnecessary files, delete the files.
613 Error in writing logfile
• Insert a SD card or USB memory.
• Turn on the SD card access switch.
• Check if the SD card or USB memory is writable.
614 Error in reading logfile
• Insert a SD card or USB memory.
• Turn on the SD card access switch.
• Check if the SD card or USB memory is readable.
615
Cannot connect to MES Server.
Check the Server.
The server does not work normally or the connection path to the server is
made up incorrectly.
• Check the operating conditions of the server.
• Check the network to the server.
616
Cannot connect to SNTP Server.
Check the Server.
The settings for the SNTP server are wrong or the network to the SNTP
server is made up incorrectly.
• Check the operating conditions of the STNP server.
• Check the network to the SNTP server.
640
An error occurred in a FTP client
process.
Reconfigure the GOT (FTP client) setting.
Check the operating status and network line of the FTP server.
For the error details, check the GOT special register GS989 (FTP
communication error notification).
800 Abnormal module status
Refer to explanations of SB0020 on the applicable network manual.
801 Abnormal baton passing status
Refer to explanations of SB0047 on the applicable network manual.
802
Abnormal cyclic transmission
status
803 Transient error
850 CC-Link switch setting error
851
Abnormal cyclic transmission
status
Refer to explanations of SB0049 on the applicable network manual.
Refer to explanations of SB00EE on the applicable network manual.
• Check if the switch settings have no error.
• Check error codes stored in SW006A.
• Refer to explanations of SB006A on the applicable network manual
•
•
•
•
•
Check if terminating resistors are connected.
Check error codes for the PLC CPU.
Check the parameter for the PLC CPU on the master station.
Check the error status of the master station.
Refer to explanations of SB006E on the applicable network manual.
852 Abnormal host line status
• Check if the cable is unplugged or not.
• Refer to explanations of SB0090 on the applicable network manual.
853 Transient error
• Check the transient error occurrence status for each station stored in
SW0094 to SW0097.
• Refer to explanations of SB0094.
*1
18 - 20
The error may be caused by a failure in the GOT. Please consult your
local Mitsubishi (Electric System) Service center or representative.
When an error occurs, "FFH" is stored to the channel No.
18. TROUBLESHOOTING
18.2 Error Message and System Alarm
Channel No.
storage
APPENDICES
MAINTENANCE AND
INSPECTION
17
Appendix.1 External Dimensions
18
TROUBLESHOOTING
 External dimensions of GT14
164(6.46")
120(4.73")
10
(0.4")
22
(0.87")
23(0.91")
47(1.86")
56(2.17")
Panel thickness:
2mm 4mm(0.08" 0.16") or less
152(5.99")
Unit: mm (inch)
 External dimensions of stand
153(6.03")
220(8.67")
254(10.0")
121
(4.77")
For angle of 75
260(10.24")
Unit: mm (inch)
APPENDICES
Appendix.1 External Dimensions
App - 1
APPENDICES
M2.6
(Metric screw type)
10
(0.4")
120(4.73")
6(0.24")
22
(0.87")
120(4.73")
135(5.32")
#4-40UNC
(Inch screw type)
 External dimensions of serial multi-drop connection unit
Protective cover is removed
90(3.55")
72(2.84")
Protective cover is installed
2- 4.5
80(3.15")
57(2.25")
65(2.56")
Unit : mm (inch)
48(1.89")
 External dimensions of connector conversion adapter
36(1.42")
22
(0.87")
Unit : mm (inch)
App - 2
APPENDICES
Appendix.1 External Dimensions
17
48(1.89")
MAINTENANCE AND
INSPECTION
 External dimensions of RS-232/485 signal conversion adapter
17
(0.67")
Unit : mm (inch)
APPENDICES
36(1.42")
TROUBLESHOOTING
18
APPENDICES
Appendix.1 External Dimensions
App - 3
 External dimensions of communication cable
Unit: mm (inch)
GT01-C30R4-25P
50(1.97")
16
(0.63")
30000(1181.1")
53(2.09")
16
(0.63")
55(2.17")
35(1.38")
7
(0.28")
M2.6
M2.6
GT01-C
R4-25P
50(1.97")
16
(0.63")
L
53(2.09")
16
(0.63")
55(2.17")
35(1.38")
7
(0.28")
M2.6
M2.6
Length L mm (inch)
Value of
GT01-C
16
(0.63")
100
10000
200
20000
300
30000
R4-8P
50(1.97")
L
35(1.38")
6
25×33
(0.99") (1.3")
M2.6
Value of
App - 4
40(1.58")
Length L mm (inch)
10
1000
30
3000
100
10000
200
20000
300
30000
APPENDICES
Appendix.1 External Dimensions
13
(0.52")
MAINTENANCE AND
INSPECTION
17
GT01-C30R2-25P
50(1.97")
30000(1181.1")
53(2.09")
16
(0.63")
18
55(2.17")
35(1.38")
6
#4-40UNC
TROUBLESHOOTING
16
(0.63")
M2.6
GT01-C30R2-9S
50(1.97")
30000(1181.1")
50(1.97")
16
(0.63")
#4-40UNC
35(1.38")
35(1.38")
φ6
#4-40UNC
APPENDICES
16
(0.63")
GT01-C30R2-6P
35(1.38")
16
(0.63")
50(1.97")
30000(1181.1")
7
(0.28")
40(1.58")
20×28
(0.79") (1.11")
13
(0.52")
#4-40UNC
APPENDICES
Appendix.1 External Dimensions
App - 5
App - 6
APPENDICES
Appendix.1 External Dimensions
Appendix.2 Usage Condition of Utility Function
The function which can be used differs according to the GOT type.
Moreover, there are the function which can be set with drawing software and the function which cannot be set.
: Applicable
Item
: Not applicable -: Not required
Functions overview
GT14
GT11
Drawing
Setting
Communication
setting
Communication setting
Setting communication parameters
Setting or deleting sequence program protection key words, canceling
sequence program protection status (When connecting to FX series CPU)
Ethernet setting
18
TROUBLESHOOTING
Assigning channel numbers and communication drivers to communication
interfaces
MAINTENANCE AND
INSPECTION
17
Displaying the contents of Ethernet setting, changing the host
Switching message languages
Setting the startup screen display time and screen saving time
Setting the backlight to ON or OFF during screen saving
Setting the battery alarm display to ON or OFF
APPENDICES
Display
Adjusting brightness and contrast
Inverting colors
Setting the buzzer volume and window move buzzer
Setting the key sensitivity and key reaction speed
GOT setup
Operation
Changing security levels
Setting the utility call keys
Adjusting the touch panel
Setting the USB mouse and keyboard
Transparent mode
Setting the channel No. to be used for the communication for the FA
transparent function
Setting the storage locations for backup data and backup settings, and
setting the maximum number of backup data
Backup/restoration
Trigger backup settings
Setting the CPU No. setting at backup to "YES" or "NO"
Behavior of duplicate IPs
Setting the GOT operation when a device with the same IP address as that
of the GOT is added to the network afterwards
OS information
Installing or uploading OS, displaying OS property, checking OS data
Alarm information
Deleting or copying alarm log files
Converting alarm log files in G1A format
CSV or TXT format
Project information
Downloading, uploading, deleting or copying project files, displaying project
file property, checking project file data
Hard copy information
Deleting or copying hard copy files, changing hard copy file names
Converting advanced recipe files in G1P format
Advanced Recipe information
Program/
data control
Converting logging files in G1L format
Logging information
CSV or TXT format
Converting advanced recipe files in CSV or TXT format
G1P format
Deleting, copying or moving advanced recipe files, creating a new advanced
recipe file
Deleting or moving advanced recipe folders, changing advanced recipe
folder names, creating a new advanced recipe folder
Writing, reading or matching record data and deleting device values with the
advanced recipe record list
CSV or TXT format
Deleting, copying or moving logging files, changing logging file names
Deleting logging folders or creating a new logging folder
Memory card format
Formatting a SD card or USB memory, internal SRAM
Memory information
Displaying the available memory of the GOT
USB device status display
Displaying the status of USB device
SRAM control
Back up, restoring and initializing of the SRAM user area
GOT data package acquisition
Copying the OS, special data, and project data to a CF card or USB memory
APPENDICES
Appendix.2 Usage Condition of Utility Function
App - 7
: Applicable
Item
: Not applicable -: Not required
Functions overview
Selecting a base clock
Time setting & display
Displaying and setting the clock current time
Displaying the battery status
System monitor
Debug
FX list editor
A list editor
Backup/restoration
Memory check
Drawing check
Debug & self check
Self check
Font check
Touch panel check
I/O check
Ethernet status check
Clean
App - 8
System alarm display
Displaying error code and error message
GOT start time
Displaying GOT start date and time, current time, accumulated operating
hours
Displaying the screen for cleaning the display
APPENDICES
Appendix.2 Usage Condition of Utility Function
GT14
GT11
Drawing
Setting
Appendix.3 Transportation Precautions
MAINTENANCE AND
INSPECTION
17
When transporting lithium batteries, make sure to treat them based on the transport regulations.
Appendix.3.1 Relevant models
Product name
Model name
Description
Handled as
Battery for GOT1000 series
GT11-50BAT
Lithium battery
Non-dangerous goods
Appendix.3.2 Transportation guidelines
TROUBLESHOOTING
18
The battery for the GOT1000 series is classified as shown in the table below.
APPENDICES
Products are packed properly in compliance with the transportation regulations prior to shipment. When repacking any of
the unpacked products to transport it to another location, make sure to observe the IATA Dangerous Goods Regulations,
IMDG Code and other local transportation regulations.
For details, please consult your transportation company.
APPENDICES
Appendix.3 Transportation Precautions
App - 9
App - 10
APPENDICES
Appendix.3 Transportation Precautions
INDEX
A list editor........................................................... 14-1
ABBREVIATIONS AND GENERIC TERMS ........ A-15
Adjusting the touch panel position..................... 11-13
Advanced recipe information ............................. 13-33
Alarm information .............................................. 13-11
[B]
Backlight Shutoff Detection ................................. 17-7
Backup/restoration............................................... 14-2
Backup/Restoration Setting ............................... 11-19
Battery ........................................................... 8-4,17-4
Battery alarm display ................................... 11-1,11-4
Behavior of Duplicate IPs .................................. 11-22
BootOS ................................................................ 16-1
Brightness, contrast..................................... 11-1,11-5
Buzzer volume setting ................................. 11-6,11-8
[C]
Clean ........................................................... 15-1,17-3
Cleaning of display section.................................. 15-1
Communication Detail Setting ............................. 10-8
Communication setting ........................................ 10-1
Connector Conversion Adapter ........................... 8-11
CoreOS.............................................................. 16-11
[D]
Daily Inspection ................................................... 17-2
Data type and storage location............................ 13-1
Debug .................................................................. 14-1
Display Setting..................................................... 11-1
Drawing check ..................................................... 14-6
[E]
Error Message ......................................... 18-11,18-13
Ethernet Setting................................................. 10-15
Ethernet status check ........................................ 14-17
External Dimensions.......................................... App-1
[F]
FILE DISPLAY AND COPY ................................. 13-1
Font check ......................................................... 14-10
FX list editor......................................................... 14-1
[G]
GOT data package acquisition .......................... 13-73
GOT internal battery voltage status..................... 12-3
GOT Restoration Sheet ....................................... 18-1
GOT start time ................................................... 14-21
[H]
Hard copy information ....................................... 13-27
[I]
I/O check............................................................ 14-14
INSTALLATION ..................................................... 6-1
[K]
Key sensitivity setting .................................. 11-6,11-8
[L]
Language..................................................... 11-1,11-3
Logging information ........................................... 13-53
[M]
MAINTENANCE AND INSPECTION ................... 17-1
Memory card format........................................... 13-63
Memory check ..................................................... 14-3
Memory information ........................................... 13-65
[O]
Opening screen time.................................... 11-1,11-4
OS information..................................................... 13-5
OS version confirmation ...................................... 13-3
[P]
Panel Cutting Dimension ....................................... 6-2
Panel-Mounted USB Port Extension.................... 8-14
PARTS NAME ....................................................... 4-1
Back Panel ......................................................... 4-2
Front Panel......................................................... 4-1
Rear Face .......................................................... 4-3
Periodic Inspection .............................................. 17-2
Project Information............................................. 13-17
Protective Cover for Oil.......................................... 8-7
Protective Sheet .................................................... 8-6
[R]
RS-232/485 signal conversion adapter................ 8-16
[S]
Screen save backlight.................................. 11-1,11-4
Screen save time ......................................... 11-1,11-4
SD Card ................................................................. 8-1
Security level change........................................... 11-9
Self Check ........................................................... 14-3
Serial Multi-Drop Connection Unit ....................... 8-12
SPECIFICATIONS................................................. 3-1
General Specifications ....................................... 3-1
Performance Specifications ............................... 3-2
Power Supply Specifications.............................. 3-3
SRAM control..................................................... 13-68
Stand ................................................................... 8-10
Standard monitor OS ........................................... 16-1
System Alarm .......................................... 18-11,18-13
System Alarm Display........................................ 14-19
Index-1
INDEX
[A]
SYSTEM CONFIGURATION................................. 2-1
Overall Configuration ......................................... 2-1
System Equipment ............................................. 2-1
System monitor.................................................... 14-1
[T]
Time Setting and Display..................................... 12-1
Clock display .................................................... 12-3
Clock setting..................................................... 12-2
Touch panel check ............................................ 14-12
Transparent Mode Setting ................................. 11-18
Transportation Precautions ............................... App-9
TROUBLESHOOTING ........................................ 18-1
[U]
UL, cUL STANDARDS AND EMC DIRECTIVE..... 5-1
USB device status display ................................. 13-66
USB Environmental Protection Cover.................... 8-9
USB memory ......................................................... 8-3
USB mouse/keyboard setting ............................ 11-15
Utility Call Key Setting ....................................... 11-11
UTILITY FUNCTION....................................9-1,App-7
Display ............................................................... 9-4
Function List....................................................... 9-2
[W]
Window move buzzer volume setting .......... 11-6,11-8
WIRING ................................................................. 7-1
Power Supply Wiring.......................................... 7-2
Wiring inside....................................................... 7-5
Wiring outside .................................................... 7-5
Index-2
REVISIONS
* The manual number is given on the bottom left of the back cover.
* Manual Number
Sub
Number
Oct., 2011
JY997D44801
A
First edition
Jan., 2012
JY997D44801
B
Compatible with GT Works3 Version1.40S
• GT14-RS2T4-9P type RS-232/485 signal conversion adaptor compatible
Jan., 2012
JY997D44801
C
Compatible with GT Works3 Version1.40S
• UL, cUL Standards supported
Apr., 2012
JY997D44801
D
Compatible with GT Works3 Version1.45X
• The backup/restoration setting function is added.
Jun., 2012
JY997D44801
E
Compatible with GT Works3 Version1.54G
• Partial changes of general specifications(frequency)
• Connection of printer compatible
• Ethernet status check compatible
• Company name changes (from YAMATAKE to AZBIL, from PANASONIC EW to PANASONIC)
Sep., 2012
JY997D44801
F
Compatible with GT Works3 Version1.58L
• Operator information management is added.
Feb., 2013
JY997D44801
G
Compatible with GT Works3 Version1.67V
• SAFETY PRECAUTIONS is changed.
Print Date
Revision
• VNC® server function is added.
Jun., 2013
JY997D44801
H
• SAFETY PRECAUTIONS is changed.
• The restrictions of UL, cUL Standards is added.
This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent licenses. Mitsubishi Electric
Corporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the
contents noted in this manual.
© 2011 MITSUBISHI ELECTRIC CORPORATION
REVISIONS - 1
REVISIONS - 2
WARRANTY
Please confirm the following product warranty details before using this product.
1. Gratis Warranty Term and Gratis Warranty Range
If any faults or defects (hereinafter "Failure") found to be the responsibility of Mitsubishi occurs during use of the product within the
gratis warranty term, the product shall be repaired at no cost via the sales representative or Mitsubishi Service Company.
However, if repairs are required onsite at domestic or overseas location, expenses to send an engineer will be solely at the
customer's discretion. Mitsubishi shall not be held responsible for any re-commissioning, maintenance, or testing on-site that
involves replacement of the failed module.
[Gratis Warranty Term]
The gratis warranty term of the product shall be for thirty-six (36) months after the date of purchase or delivery to a designated
place.
Note that after manufacture and shipment from Mitsubishi, the maximum distribution period shall be six (6) months, and the
longest gratis warranty term after manufacturing shall be forty-two (42) months. The gratis warranty term of repair parts shall not
exceed the gratis warranty term before repairs.
[Gratis Warranty Range]
(1) The customer shall be responsible for the primary failure diagnosis unless otherwise specified.
If requested by the customer, Mitsubishi Electric Corporation or its representative firm may carry out the primary failure
diagnosis at the customer’s expense.
The primary failure diagnosis will, however, be free of charge should the cause of failure be attributable to Mitsubishi Electric
Corporation.
(2) The range shall be limited to normal use within the usage state, usage methods and usage environment, etc., which follow
the conditions and precautions, etc., given in the instruction manual, user's manual and caution labels on the product.
(3) Even within the gratis warranty term, repairs shall be charged for in the following cases.
1. Failure occurring from inappropriate storage or handling, carelessness or negligence by the user. Failure caused by the
user's hardware or software design.
2. Failure caused by unapproved modifications, etc., to the product by the user.
3. When the Mitsubishi product is assembled into a user's device, Failure that could have been avoided if functions or
structures, judged as necessary in the legal safety measures the user's device is subject to or as necessary by industry
standards, had been provided.
4. Failure that could have been avoided if consumable parts designated in the instruction manual had been correctly
serviced or replaced.
5. Replacing consumable parts such as the battery, backlight and fuses.
6. Failure caused by external irresistible forces such as fires or abnormal voltages, and Failure caused by force majeure
such as earthquakes, lightning, wind and water damage.
7. Failure caused by reasons unpredictable by scientific technology standards at time of shipment from Mitsubishi.
8. Any other failure found not to be the responsibility of Mitsubishi or that admitted not to be so by the user.
2. Onerous repair term after discontinuation of production
(1) Mitsubishi shall accept onerous product repairs for seven (7) years after production of the product is discontinued.
Discontinuation of production shall be notified with Mitsubishi Technical Bulletins, etc.
(2) Product supply (including repair parts) is not available after production is discontinued.
3. Overseas service
Overseas, repairs shall be accepted by Mitsubishi's local overseas FA Center. Note that the repair conditions at each FA Center
may differ.
4. Exclusion of loss in opportunity and secondary loss from warranty liability
Regardless of the gratis warranty term, Mitsubishi shall not be liable for compensation to damages caused by any cause found not
to be the responsibility of Mitsubishi, loss in opportunity, lost profits incurred to the user by Failures of Mitsubishi products, special
damages and secondary damages whether foreseeable or not, compensation for accidents, and compensation for damages to
products other than Mitsubishi products, replacement by the user, maintenance of on-site equipment, start-up test run and other
tasks.
5. Changes in product specifications
The specifications given in the catalogs, manuals or technical documents are subject to change without prior notice.
6. Product application
(1) In using the Mitsubishi graphic operation terminal, the usage conditions shall be that the application will not lead to a major
accident even if any problem or fault should occur in the graphic operation terminal device, and that backup and fail-safe
functions are systematically provided outside of the device for any problem or fault.
(2) The Mitsubishi graphic operation terminal has been designed and manufactured for applications in general industries, etc.
Thus, applications in which the public could be affected such as in nuclear power plants and other power plants operated by
respective power companies, and applications in which a special quality assurance system is required, such as for Railway
companies or Public service purposes shall be excluded from the graphic operation terminal applications.
In addition, applications in which human life or property that could be greatly affected, such as in aircraft, medical applications,
incineration and fuel devices, manned transportation equipment for recreation and amusement, and safety devices, shall also
be excluded from the graphic operation terminal range of applications.
However, in certain cases, some applications may be possible, providing the user consults the local Mitsubishi representative
outlining the special requirements of the project, and providing that all parties concerned agree to the special circumstances,
solely at our discretion.
In some of three cases, however, Mitsubishi Electric Corporation may consider the possibility of an application, provided that
the customer notifies Mitsubishi Electric Corporation of the intention, the application is clearly defined and any special quality is
not required.
GOT is a registered trademark of Mitsubishi Electric Corporation.
Microsoft, Windows, Windows NT, Windows Server, Windows Vista, and Windows 7 are registered trademarks or trademarks
of Microsoft Corporation in the United States and other countries.
Adobe and Adobe Reader are registered trademarks of Adobe Systems Incorporated.
Pentium and Celeron are a registered trademarks of Intel Corporation in the United States and other countries.
Ethernet is a trademark of Xerox Corporation in the United States.
MODBUS is a trademark of Schneider Electric SA.
VNC is a registered trademark of RealVNC Ltd. in the United States and other countries.
Other company and product names herein are either trademarks or registered trademarks of their respective owners.
">