Moxa EDS-316 Manual - Allied Automation, Inc.

Moxa EDS-316 Manual - Allied Automation, Inc.
EDS-316
Hardware Installation Guide
Moxa EtherDevice Switch
Fourth Edition, April 2014
 2014 Moxa Inc. All rights reserved.
P/N: 1802003160011
Overview
The Moxa EtherDevice™ EDS-316 Series of 16-port smart Ethernet
switches provides an economical solution for your Ethernet connections.
As an added bonus, the built-in smart alarm function helps system
maintainers monitor the health of your Ethernet network.
EDS-316 has a wide operating temperature range of -40 to 75°C, and is
designed to withstand a high degree of vibration and shock. The rugged
hardware design makes EDS-316 Series perfect for ensuring that your
Ethernet equipment can withstand critical industrial applications, such as
in hazardous locations (Class 1 Division 2/ Zone 2), and complies with
FCC, TÜV, UL, and CE Standards.
NOTE
Throughout this Hardware Installation Guide, we use EDS as an
abbreviation for Moxa EtherDevice Switch:
EDS = Moxa EtherDevice Switch
Package Checklist
Moxa EDS-316 is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service
representative for assistance.
•
•
•
•
Moxa EtherDevice™ Switch
Protective caps for unused ports
Hardware Installation Guide
Moxa Product Warranty Card
Features
High Performance Network Switching Technology
•
•
•
•
10/100BaseT(X) (RJ45), 100BaseFX (SC/ST type, Multi/Single mode)
IEEE 802.3/802.3u/802.3x
Store and Forward switching process type, with 4K address entries
10/100M, Full/Half-Duplex, MDI/MDIX auto-sensing
Industrial Grade Reliablity
•
•
•
Power failure, port break alarm by relay output
Redundant dual DC power inputs
Broadcast storm protection to prevent network devices from crashing
Rugged Design
•
•
•
Operating temperature range of 0 to 60°C, or extended operating
temperature of -40 to 75°C for (-T) models
IP30, rugged high-strength case
DIN-Rail or wall mounting ability
-2-
Panel Layout of EDS-316 (standard-type)
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
-3-
Grounding screw
Terminal block for power input
(PWR1, PWR2) and relay output
Heat dissipation orifices
DIP switches
(EDS-316 has 18 DIP switches in
total; 2 DIP switches are
reserved)
Power input PWR1 LED
Power input PWR2 LED
Fault LED
10/100BaseT(X) Port
TP port’s 100 Mbps LED
TP port’s 10 Mbps LED
Model Name
Screw hole for wall mounting kit
DIN-Rail Kit
Panel Layout of EDS-316 (SC-type)
Product models not shown here:
EDS-316-S-SC is identical to
EDS-316-M-SC.
EDS-316-SS-SC and EDS-316-MS-SC
are identical to EDS-316-MM-SC.
1. Grounding screw
2. Terminal block for power input
(PWR1, PWR2) and relay output
3. Heat dissipation orifices
4. DIP switches (EDS-316 series has
18 DIP switches in total; 2 DIP
switches are reserved)
5. Power input PWR1 LED
6. Power input PWR2 LED
7. Fault LED
8. 10/100BaseT(X) Port
9. TP port’s 100 Mbps LED
10. TP port’s 10 Mbps LED
11. Model Name
12. 100BaseFX Port
SSC for EDS-316-MS-SC
SSC-80 for EDS-316-SS-SC-40/80
13. 100BaseFX Port
MSC for EDS-316-MS-SC
SSC-40 for EDS-316-SS-SC-40/80
14. FX port’s 100 Mbps LED
15. Screw hole for wall mounting kit
16. DIN-Rail Kit
NOTE
MSC = Multi-Mode SC Connector
SSC = Single-Mode SC Connector
SSC-80 = Single-Mode SC Connector (80 km)
-4-
Panel Layout of EDS-316 (ST-type)
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Grounding screw
Terminal block for power input
(PWR1, PWR2) and relay output
Heat dissipation orifices
DIP switches
(EDS-316 has 18 DIP switches in
total; 2 DIP switches are reserved)
Power input PWR1 LED
Power input PWR2 LED
Fault LED
10/100BaseT(X) Port
TP port’s 100 Mbps LED
TP port’s 10 Mbps LED
Model Name
100BaseFX Port
FX port’s 100 Mbps LED
Screw hole for wall mounting kit
DIN-Rail Kit
-5-
Mounting Dimensions
Unit = mm (inch)
DIN-Rail Mounting
The aluminum DIN-Rail attachment plate should already be fixed to the
back panel of EDS-316 when you take it out of the box. If you need to
reattach the DIN-Rail attachment plate, make sure the stiff metal spring
is situated towards the top, as shown in the figures below.
STEP 1:
Insert the top of the DIN-Rail into
the slot just below the stiff metal
spring.
STEP 2:
The DIN-Rail attachment unit will
snap into place as shown below.
To remove Moxa EtherDevice Switch from the DIN-Rail, simply reverse
Steps 1 and 2 above.
-6-
Wall Mounting (optional)
For some applications, you will find it convenient to mount EDS-316 on
the wall, as illustrated in the figure.
STEP 1: Remove the
aluminum DIN-Rail
attachment plate from
EDS-316’s rear panel, and
then attach the wall mount
plates, as shown in the figure.
STEP 2: Mounting EDS-316 on the wall requires 4
screws. Use the switch, with wall mount plates
attached, as a guide to mark the correct locations of the
4 screws. The heads of the screws should be less than
6.0 mm in diameter, and the shafts should be less than
3.5 mm in diameter, as shown in the figure at the right.
NOTE
Before tightening screws into the wall, make sure the screw head
and shank size are suitable by inserting the screw into one of the
keyhole-shaped apertures of the Wall Mounting Plates.
Do not screw the screws in all the way—leave about 2 mm to allow room
for sliding the wall mount panel between the wall and the screws.
STEP 3: Once the screws are fixed
in the wall, insert the four screw
heads through the large parts of
the keyhole-shaped apertures,
and then slide EDS-316
downwards, as indicated. Tighten
the four screws for added stability.
ATEX Information
1.
2.
3.
4.
5.
Certificate number DEMKO 08 ATEX 0812123x
Ambient range (-40°C ≤ Tamb ≤ 75°C)
Certification string (Ex nA nC IIC T4 Gc)
Standards covered ( EN 60079-0:2012, EN 60079-15:2010)
The conditions of safe usage:
• These products must be mounted in an IP54 enclosure.
• Install in an area of pollution degree 2 or less.
• Use a conductor wire of size 0.2 mm² or greater.
• Conductors suitable for use in an ambient temperature of 93°C
must be used for the Power Supply Terminal.
• PROVISIONS SHALL BE MADE, EITHER IN EXTERNAL TO THE
APPARATUS, TO PREVENT THE RATED VOLTAGE BEING
EXCEEDED BY THE TRANSIENTS DISTURBANCES OF MORE
THAN 40 %
-7-
Wiring Requirements
WARNING
Do not disconnect modules or wires unless the power supply has
been switched off or the area is known to be non-hazardous. The
devices may only be connected to the supply voltage shown on
the type plate.
The devices are designed for operation with a Safety Extra-Low
Voltage. Thus, they may only be connected to the supply voltage
connections and to the signal contact with the Safety Extra-Low
Voltages (SELV) in compliance with IEC950/ EN60950/ VDE0805.
WARNING
Substitution of components may impair suitability for Class I,
Division 2, and Zone 2. These devices must be supplied by an
SELV source as defined in Low Voltage Directive 73/23/EEC and
93/68/EEC.
WARNING
This unit is a built-in type. When the unit is installed in another
piece of equipment, the equipment enclosing the unit must
comply with fire enclosure regulation IEC 60950/EN60950 (or
similar regulation).
WARNING
Safety First!
Be sure to disconnect the power cord before installing and/or
wiring your Moxa EtherDevice Switch.
Calculate the maximum possible current in each power wire and
common wire. Observe all electrical codes dictating the
maximum current allowable for each wire size.
If the current goes above the maximum ratings, the wiring could
overheat, causing serious damage to your equipment.
You should also pay attention to the following items:
•
•
Use separate paths to route wiring for power and devices. If power
wiring and device wiring paths must cross, make sure the wires are
perpendicular at the intersection point.
NOTE: Do not run signal or communications wiring and power wiring
in the same wire conduit. To avoid interference, wires with different
signal characteristics should be routed separately.
You can use the type of signal transmitted through a wire to
determine which wires should be kept separate. The rule of thumb is
that wiring that shares similar electrical characteristics can be
bundled together.
-8-
•
•
Keep input wiring and output wiring separated.
It is strongly advised that you label wiring to all devices in the system
when necessary.
Grounding Moxa EtherDevice Switch
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from the
ground screw to the grounding surface prior to connecting devices.
ATTENTION
This product is intended to be mounted to a well-grounded
mounting surface, such as a metal panel.
Wiring the Alarm Contact
The Alarm Contact consists of the two middle contacts of the terminal
block on EDS’s top panel. You may refer to the next section for detailed
instructions on how to connect the wires to the terminal block connector,
and how to attach the terminal block connector to the terminal block
receptor.
In this section, we explain the meaning of the two contacts used to
connect the Alarm Contact.
FAULT: The two middle contacts of the 6-contact
terminal block connector are used to detect both
power faults and port faults. The two wires attached
to the Fault contacts form an open circuit when:
1. EDS has lost power from one of the DC power
inputs.
OR
2. The PORT ALARM DIP Switch for one of the ports
is set to ON, but the port is not connected
properly.
If neither of these two conditions is satisfied, the
Fault circuit will be closed.
Wiring the Redundant Power Inputs
The top two contacts and the bottom two contacts of the 6-contact
terminal block connector on EDS’s top panel are used for EDS’s two DC
inputs. Top and front views of one of the terminal block connectors are
shown here.
STEP 1: Insert the negative/positive DC wires into
the V-/V+ terminals.
STEP 2: To keep the DC wires from pulling loose, use
a small flat-blade screwdriver to tighten the
wire-clamp screws on the front of the terminal block
connector.
STEP 3: Insert the plastic terminal block connector
prongs into the terminal block receptor, which is
located on EDS’s top panel.
-9-
ATTENTION
Before connecting EDS to the DC power inputs, make sure the DC
power source voltage is stable.
Communication Connections
EDS-316 models have 14, 15, or 16 10/100BaseT(X) Ethernet ports, and
2, 1, or 0 (zero) 100BaseFX (SC/ST-type connector) fiber ports.
10/100BaseT(X) Ethernet Port Connection
The 10/100BaseT(X) ports located on EDS’s front panel are used to
connect to Ethernet-enabled devices.
Below we show pinouts for both MDI (NIC-type) ports and MDI-X
(HUB/Switch-type) ports, and also show cable wiring diagrams for
straight-through and cross-over Ethernet cables.
10/100Base T(x) RJ45 Pinouts
MDI Port Pinouts
Pin
Signal
1
Tx+
2
Tx3
Rx+
6
Rx-
MDI-X Port Pinouts
Pin
Signal
1
Rx+
2
Rx3
Tx+
6
Tx-
8-pin RJ45
RJ45 (8-pin) to RJ45 (8-pin) Straight-Through Cable Wiring
RJ45 (8-pin) to RJ45 (8-pin) Cross-Over Cable Wiring
100BaseFX Ethernet Port Connection
The concept behind the SC/ST port and cable is very straightforward.
Suppose you are connecting devices I and II. Contrary to electrical signals,
optical signals do not require a circuit in order to transmit data.
Consequently, one of the optical lines is used to transmit data from device
I to device II, and the other optical line is used transmit data from device
II to device I, for full-duplex transmission.
- 10 -
All you need to remember is to connect the Tx (transmit) port of device I
to the Rx (receive) port of device II, and the Rx (receive) port of device I
to the Tx (transmit) port of device II. If you make your own cable, we
suggest labeling the two sides of the same line with the same letter
(A-to-A and B-to-B, as shown below, or A1-to-A2 and B1-to-B2).
SC-Port Pinouts
SC-Port to SC-Port Cable Wiring
ST-Port Pinouts
ST-Port to ST-Port Cable Wiring
ATTENTION
This is a Class 1 Laser/LED product. To avoid causing serious
damage to your eyes, do not stare directly into the Laser Beam.
Redundant Power Inputs
Both power inputs can be connected simultaneously to live DC power
sources. If one power source fails, the other live source acts as a backup,
and automatically supplies all of EDS-316’s power needs.
Alarm Contact
Moxa EtherDevice Switch has one Alarm Contact located on the top panel.
For detailed instructions on how to connect the Alarm Contact power
wires to the two middle contacts of the 6-contact terminal block
connector, see the Wiring the Alarm Contact section on page 7. A typical
scenario would be to connect the Fault circuit to a warning light located in
the control room. The light can be set up to switch on when a fault is
detected.
The Alarm Contact has two terminals that form a Fault circuit for
connecting to an alarm system. The two wires attached to the Fault
contacts form an open circuit when (1) EDS has lost power from one of
the DC power inputs, or (2) The PORT ALARM DIP Switch for one of the
ports is set to ON, but the port is not connected properly.
If neither of these two conditions occurs, the Fault circuit will be closed.
- 11 -
DIP Switch Settings
EDS-316 Series DIP Switches
DIP Switch
Setting
Port Alarm
Function
(P1 to P16)
Broadcast
Storm
Protection
(BSP)
NOTE
ON
OFF
ON
OFF
Description
Enables the corresponding PORT Alarm. If the
port’s link fails, the relay will form an open circuit
and the fault LED will light up.
Disables the corresponding PORT Alarm. The
relay will form a closed circuit and the Fault LED
will never light up.
Enables the broadcast storm protection in the
EDS switch for all ports.
Disables the broadcast storm protection.
The EDS-316 has a total of 18 DIP switches; 1 DIP switch is
reserved.
LED Indicators
The front panel of Moxa EtherDevice Switch contains several LED
indicators. The function of each LED is described in the table below.
LED
Color
PWR1
AMBER
PWR2
AMBER
FAULT
RED
10M
GREEN
100M
(TP)
GREEN
100M
(FX)
GREEN
State
On
Description
Power is being supplied to power input PWR1
Power is not being supplied to power input
Off
PWR1
On
Power is being supplied to power input PWR2
Power is not being supplied to power input
Off
PWR2
When the corresponding PORT alarm is
On
enabled, and the port’s link is inactive.
When the corresponding PORT alarm is
Off
enabled and the port’s link is active, or when
the corresponding PORT alarm is disabled.
On
TP port’s 10 Mbps link is active
Blinking Data is being transmitted at 10 Mbps
Off
TP Port’s 10 Mbps link is inactive
On
TP port’s 100 Mbps link is active
Blinking Data is being transmitted at 100 Mbps
Off
100BaseTX Port’s link is inactive
On
FX port’s 100 Mbps is active
Blinking Data is being transmitted at 100 Mbps
Off
100BaseFX port is inactive
- 12 -
Auto MDI/MDI-X Connection
The Auto MDI/MDI-X function allows users to connect EDS-316’s
10/100BaseTX ports to any kind of Ethernet device, without needing to
pay attention to the type of Ethernet cable being used for the connection.
This means that you can use either a straight-through cable or cross-over
cable to connect EDS-316 to Ethernet devices.
Fiber Ports
Moxa EDS-316’s fiber switched ports operate at a fixed 100 Mbps speed
and full-duplex mode to provide the best performance. The fiber ports are
factory-built as either a multi-mode or single-mode SC/ST connector.
Consequently, you should use fiber cables that have SC/ST connectors at
both ends. When plugging the connector into the port, make sure the
slider guide is positioned to the right side so that it fits snuggly into the
port.
The 100 Mbps fiber ports are switched ports, and perform as a domain,
providing a high bandwidth backbone connection that supports long fiber
cable distances (up to 5 km for multi-mode, and 40 km, and 80 km for
single-mode) for installation versatility.
Dual Speed Functionality and Switching
Moxa EDS-316’s 10/100 Mbps switched RJ45 port auto negotiates with
the connected device for the fastest data transmission rate supported by
both devices. All models of Moxa EtherDevice Switch are plug-and-play
devices, so that software configuration is not required at installation, or
during maintenance. The half/full duplex mode for the switched RJ45
ports is user dependent and changes (by auto-negotiation) to full or half
duplex, depending on which transmission speed is supported by the
attached device.
Switching, Filtering, and Forwarding
Each time a packet arrives at one of the switched ports, a decision is
made to either filter or forward the packet. Packets with source and
destination addresses belonging to the same port segment will be filtered,
constraining those packets to one port, and relieving the rest of the
network from the need to process them. A packet with destination
address on another port segment will be forwarded to the appropriate
port, and will not be sent to the other ports where it is not needed.
- 13 -
Packets that are used in maintaining the operation of the network (such
as the occasional multi-cast packet) are forwarded to all ports.
EDS-316 operates in the store-and-forward switching mode, which
eliminates bad packets and enables peak performance to be achieved
when there is heavy traffic on the network.
Switching and Address Learning
Moxa EDS-316 has an address table that can hold up to 4K node
addresses, which makes it suitable for use with large networks. The
address tables are self-learning, so that as nodes are added or removed,
or moved from one segment to another, EDS-316 automatically keeps up
with new node locations. An address-aging algorithm causes the
least-used addresses to be deleted in favor of newer, more frequently
used addresses. To reset the address buffer, power down the unit and
then power it back up.
Auto-Negotiation and Speed Sensing
All of EDS-316’s RJ45 Ethernet ports independently support
auto-negotiation for speeds in the 10BaseT and 100BaseTX modes, with
operation according to the IEEE 802.3u standard. This means that some
nodes could be operating at 10 Mbps, while at the same time, other nodes
are operating at 100 Mbps.
Auto-negotiation takes place when an RJ45 cable connection is made, and
then each time a LINK is enabled. EDS-316 advertises its capability for
using either 10 Mbps or 100 Mbps transmission speeds, with the device at
the other end of the cable expected to similarly advertise. Depending on
what type of device is connected, this will result in agreement to operate
at a speed of either 10 Mbps or 100 Mbps.
If an EDS-316 RJ45 Ethernet port is connected to a non-negotiating
device, it will default to 10 Mbps speed and half-duplex mode, as required
by the IEEE 802.3u standard.
Specifications
Technology
Standards
Forward and Filtering
Rate
Packet Buffer Memory
Processing Type
Address Table Size
Interface
RJ45 Ports
Fiber Ports
LED Indicators
DIP Switch
Alarm Contact
IEEE802.3, 802.3u, 802.3x
148810 pps (100M), 14881 pps (10M)
1.25 MB
Store and Forward, with IEEE802.3x full duplex,
back pressure flow control
4K uni-cast addresses
10/100BaseT(X) auto negotiation speed, F/H
duplex mode, and auto MDI/MDI-X connection
100BaseFX ports (SC/ST connector)
Power, Fault, 10/100M
Port break alarm mask
One relay output with current carrying capacity of
1A @ 24 VDC
- 14 -
Optical Fiber
100 BaseFX
Multi-mode
Single-mode Single-mode, 80 km
Wavelength
1300 nm
1310 nm
1550 nm
Max. TX
-10 dBm
0 dBm
0 dBm
Min. TX
-20 dBm
-5 dBm
-5 dBm
RX Sensitivity
-32 dBm
-34 dBm
-34 dBm
Link Budget
12 dB
29 dB
29 dBm
Typical Distance
5 kma
c
40 km
80 kmd
4 kmb
Saturation
-6 dBm
-3 dBm
-3 dBm
a. 50/125 µm, 800 MHz*km fiber optic cable
b. 62.5/125 µm, 500 MHz*km fiber optic cable
c. 9/125 µm, single-mode fiber optic cable
d. 9/125 µm, single-mode fiber optic cable (80 km)
Power
Input Voltage
12/24/48 (9 to 60) VDC, redundant inputs
Input Current @
0.34 A: EDS-316
24VDC
0.35 A: EDS-316-S-SC, EDS-316-S-SC-80
0.35 A: EDS-316-M-SC, EDS-316-M-ST
0.43 A: EDS-316-SS-SC, EDS-316-SS-SC-80,
EDS-316-SS-SC-40/80
0.43 A: EDS-316-MM-SC, EDS-316-MM-ST,
EDS-316-MS-SC, EDS-316-MS-SC-80
Connection
Removable “6-pin” Terminal Block
Overload Current
1.6 A
Protection
Reverse Polarity
None
Protection
Mechanical
Casing
IP30 protection, metal case
Dimensions
80.5 x 135 x 105 mm (W x H x D)
Weight
0.84 kg
Installation
DIN-Rail, Wall Mounting
Environmental
Operating
0 to 60°C (32 to 140°F)
Temperature
-40 to 75°C (-40 to 167°F) for -T models
Storage Temperature -40 to 85°C (-40 to 185°F)
Ambient Relative
5 to 95% (non-condensing)
Humidity
Regulatory Approvals
Safety
UL 508
Hazardous Location
UL/cUL Class I, Division 2, Groups A, B, C and D
ATEX Zone 2, Ex nA nC IIC T4 Gc
EMI
FCC Part 15, CISPR (EN 55022) class A
EMS
EN 61000-4-2 (ESD), Level 3
EN 61000-4-3 (RS), Level 3
EN 61000-4-4 (EFT), Level 3
EN 61000-4-5 (Surge), Level 3
EN 61000-4-6 (CS), Level 3
Shock
IEC 60068-2-27
Free Fall
IEC 60068-2-32
Vibration
IEC 60068-2-6
WARRANTY
5 years
- 15 -
Ordering Information
Ordering Code Definition
EDS-316-AA-BB[-CC][-T]
Fiber Port
M:
S:
MM:
SS:
MS:
FO Connector
Transmission
distance
1 Multi Mode SC: SC Connector 80: 80 km
1 Single Mode ST: ST Connector (1 or 2 ports)
2 Multi Mode
40/80: 40/80
2 Single Mode
km (for each
of 2 ports)
1 Multi,
1 Single Mode
Operating
Temperature
-T: Wide
operating Temp.
of -40 to 75°C
(Standard
Models: 0 to
60°C)
Available Models
Standard:
Long-Haul:
Wide Temperature:
EDS-316
EDS-316-MS-SC-80
EDS-316-T
EDS-316-M-SC
EDS-316-S-SC-80
EDS-316-M-SC-T
EDS-316-M-ST
EDS-316-SS-SC-80
EDS-316-M-ST-T
EDS-316-MM-SC
EDS-316-SS-SC-40/80
EDS-316-MM-SC-T
EDS-316-MM-ST
EDS-316-MM-ST-T
EDS-316-MS-SC
EDS-316-MS-SC-T
EDS-316-S-SC
EDS-316-S-SC-T
EDS-316-SS-SC
EDS-316-SS-SC-T
Please check the specifications section for detailed product information.
Optional Accessories
DR-4524:
45W/2A DIN-Rail 24 VDC Power Supply, 85 to 264
VAC input
DR-75-24:
75W/3.2A DIN-Rail 24 VDC Power Supply, 85 to 264
VAC input
DR-120-24:
120W/5A DIN-Rail 24 VDC Power Supply, 88 to 132
VAC/ 176 to 264 VAC input by switch
WK-46:
Wall Mounting Kit
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll-free: 1-888-669-2872
Tel:
1-714-528-6777
Fax: 1-714-528-6778
Moxa China (Shanghai office):
Toll-free: 800-820-5036
Tel:
+86-21-5258-9955
Fax: +86-21-5258-5505
Moxa Europe:
Tel:
+49-89-3 70 03 99-0
Fax: +49-89-3 70 03 99-99
Moxa Asia-Pacific:
Tel:
+886-2-8919-1230
Fax: +886-2-8919-1231
- 16 -
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement