CP 5612 - Siemens Industry Online Support
 CP 5612
___________________
Preface
1
___________________
Description of the device
SIMATIC NET
PG/PC - PROFIBUS
CP 5612
2
___________________
Software installation
3
___________________
Hardware installation
4
___________________
Configuration
5
___________________
Technical specifications
Operating Instructions
12/2012
C79000-G8976-C278-02
A
___________________
Approvals
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Industry Sector
Postfach 48 48
90026 NÜRNBERG
GERMANY
Order number: C79000-G8976-C278
Ⓟ 12/2012 Technical data subject to change
Copyright © Siemens AG 2012.
All rights reserved
Preface
What the consignment contains
The following components are supplied with the CP 5612:
● CP 5612 communications processor
Please check that the consignment you have received is complete. If it is not complete,
please contact your supplier or your local Siemens office.
Validity of this documentation
These operating instructions are valid for the following product:
● CP 5612
order number: 6GK1 561-2AA00
Content of this documentation
These operating instructions contain information about the installation and configuration of
the CP 5612 communications processor.
Updated operating instructions on the Internet
You will find the current version of these operating instructions on the Product Support pages
under the following entry ID:
58826992 (http://support.automation.siemens.com/WW/view/en/58826992)
Further documentation
The documents listed below contain more detailed information on commissioning and using
the communications processor. You will find this documentation on the Product Support
pages on the Internet under the following entry link:
Support (http://support.automation.siemens.com/WW/view/en)
Enter the entry ID shown below of the relevant manual as the search item.
CP 5612
Operating Instructions, 12/2012, C79000-G8976-C278-02
3
Preface
● Configuration manual Commissioning PC Stations
This provides you with detailed information on commissioning and configuring SIMATIC
NET PC communications modules.
Entry ID:
13542666 (http://support.automation.siemens.com/WW/view/en/13542666)
● System manual SIMATIC NET Industrial Communication with PG/PC
– Volume 1– Basics
Entry ID:
42783968 (http://support.automation.siemens.com/WW/view/en/42783968)
– Volume 2– Interfaces
Entry ID:
42783660 (http://support.automation.siemens.com/WW/view/en/42783660)
The system manuals introduce the topic of industrial communication and explain the
communications protocols used. There is also a description of the OPC interface as
user programming interface.
● Installation manual SIMATIC NET PC Software
This document contains detailed information on installing the SIMATIC NET
PC software.
Entry ID:
61630923 (http://support.automation.siemens.com/WW/view/en/61630923)
● System manual PROFIBUS Network Manual
In this document you will find detailed information about setting up a PROFIBUS network.
Entry ID:
35222591 (http://support.automation.siemens.com/WW/view/en/35222591)
SIMATIC NET documentation
You will find the entire SIMATIC NET documentation on the pages of Product Support:
10805878 (http://support.automation.siemens.com/WW/view/en/10805878)
Go to the required product group and make the following settings:
→ Entry list → Entry type "Manuals / Operating Instructions"
Online support
In addition to our product documentation, the comprehensive online information platform
supports you in all aspects of our Service & Support at any time and from any location in the
world. You will find this on the Internet at the following address:
(http://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo2&aktprim=99&lang=
en)
Here, you will find the following information:
CP 5612
4
Operating Instructions, 12/2012, C79000-G8976-C278-02
Preface
● Support news, newsletter
● Product information, Product Support, Applications & Tools
● Technical Forum
● Access to other features of our Service & Support offer:
– Technical Consulting
– Engineering Support
– Field Service
Phone: +49 (0)911 895 7444
– Spare parts and repairs
Phone: +49 (0)911 895 7448
– Optimization and modernization
– Technical Support
Expert advice on technical questions with a wide range of demand-optimized services
for all our products and systems.
Phone: +49 (0)911 895 7222
(https://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo&lang=en&ob
jid=38718979&caller=view)
You will find contact data on the Internet at the following address:
(http://www.automation.siemens.com/partner/guiwelcome.asp?lang=en)
SITRAIN - Siemens training for automation and industrial solutions
With over 300 different courses, SITRAIN covers the entire Siemens product and system
spectrum in the field of automation and drive technology. Advanced training tailored to your
needs is also available. In addition to our classic range of courses, we also offer a
combination of various training media and sequences. You can, for example, use self-study
programs on CD-ROM or on the Internet as preparation or to consolidate training.
You will find detailed information on our training curriculum and how to contact our customer
consultants at the following Internet address:
(www.siemens.com/sitrain)
SIMATIC NET glossary
Explanations of the specialist terms used in this documentation can be found in the SIMATIC
NET glossary.
You will find the SIMATIC NET glossary here:
● SIMATIC NET Manual Collection
The DVD ships with certain SIMATIC NET products.
● On the Internet under the following entry ID:
50305045 (http://support.automation.siemens.com/WW/view/en/50305045)
CP 5612
Operating Instructions, 12/2012, C79000-G8976-C278-02
5
Preface
CP 5612
6
Operating Instructions, 12/2012, C79000-G8976-C278-02
Table of contents
Preface ...................................................................................................................................................... 3
1
2
3
Description of the device ........................................................................................................................... 9
1.1
Product characteristics...................................................................................................................9
1.2
PROFIBUS interface....................................................................................................................10
1.3
Meaning of the LED display .........................................................................................................11
Software installation................................................................................................................................. 13
2.1
Installing the SIMATIC NET PC software ....................................................................................13
2.2
Uninstalling the SIMATIC NET PC software................................................................................13
2.3
Alternative software packets ........................................................................................................14
Hardware installation ............................................................................................................................... 15
3.1
Safety notices...............................................................................................................................15
3.2
Installing hardware.......................................................................................................................16
3.3
Hardware compatibility.................................................................................................................17
4
Configuration ........................................................................................................................................... 19
5
Technical specifications........................................................................................................................... 21
A
Approvals................................................................................................................................................. 23
Index........................................................................................................................................................ 25
CP 5612
Operating Instructions, 12/2012, C79000-G8976-C278-02
7
Table of contents
CP 5612
8
Operating Instructions, 12/2012, C79000-G8976-C278-02
Description of the device
1.1
1
Product characteristics
Properties
The CP 5612 is a communications processor for connecting PCs (personal computers) or
PGs (programming devices) to PROFIBUS and MPI networks. The essential properties are
as follows:
● Transmission speeds up to 12 Mbps.
● Floating RS-485 connector.
● Linking of up to 32 devices (PC, PG, SIMATIC S7 or ET 200) to form a network segment.
– By linking several segments with repeaters, up to 64 nodes can be connected.
● The additional interface signals for a direct link to a PLC (Programmable Logic Controller)
are supported up to 187.5 Kbps.
● Installation in PGs and PCs with a PCI slot. The following is supported:
– PCI, 33 MHz / 66 MHz, 32 bits / 64 bits
– Plug and play
CP 5612
Operating Instructions, 12/2012, C79000-G8976-C278-02
9
Description of the device
1.2 PROFIBUS interface
Appearance
The following graphic shows the CP 5612 communications processor:
3%
&3
1.2
1
LEDs
2
PROFIBUS interface PB1 (master or slave)
PROFIBUS interface
PROFIBUS network
The physical link between the PROFIBUS interface and the PROFIBUS network is via a
floating RS-485 interface that is part of the module. Depending on the network configuration,
data rates of 9.6 Kbps up to a maximum of 12 Mbps are possible in the PROFIBUS network.
Note
You will find information about the structure of a PROFIBUS network in the system manual
"PROFIBUS Network Manual". The document is part of the Manual Collection. You will also
find this on the Product Support pages under the following entry ID:
35222591 (http://support.automation.siemens.com/WW/view/en/35222591)
CP 5612
10
Operating Instructions, 12/2012, C79000-G8976-C278-02
Description of the device
1.3 Meaning of the LED display
PIN assignment
The D-sub female connector has the following pin assignment:
4
5
9
PIN
Short name
1
2
8
1
2
3
7
6
Meaning
Input/output
NC
Socket pin 1 is not connected.
-
NC (M24)
Socket pin 2 is not connected. With other MPI/DP components,
the return line of the floating 24 V power supply may be via this
pin.
-
3
LTG_B
Signal line B of the PROFIBUS connector.
Input/output
4
RTSAS
RTSAS, input signal for direct MPI link. The control signal is "1"
active when the automation system connected over a special
MPI cable is sending.
Input
5
M5EXT
M5EXT return line (GND) of the 5 V power supply. The current
load of an external consumer connected between P5EXT and
M5EXT must not exceed a maximum of 90 mA.
Output
6
P5EXT
P5EXT supply (+5 V) of the 5 V power supply. The current load
of an external consumer connected between P5EXT and
M5EXT must not exceed a maximum of 90 mA (short-circuit
proof).
Output
7
NC (P24V)
Socket pin 7 is not connected. With other MPI/DP components,
the P24V supply of the floating 24 V power supply may be via
this pin.
-
8
LTG_A
Signal line A of the PROFIBUS connector.
Input/output
9
RTS
RTS output signal of the CP module. The control signal is "1"
active when the device (PG or PC) is sending.
Output
Shield
1.3
The shield is connected to components of the connector
housing.
Meaning of the LED display
LED display
The meaning of the LED display is as follows:
Green and yellow LED
Meaning
Green on:
Shows the token rotation, in other words, normal operation.
Green off:
Incorrect bus parameters, defective bus or CP not in
operation.
CP 5612
Operating Instructions, 12/2012, C79000-G8976-C278-02
11
Description of the device
1.3 Meaning of the LED display
Green and yellow LED
Meaning
Green flashes fast, yellow is off:
Module not started; normal status following reset.
Green and yellow flashing alternately:
When using more than one module in a PG/PC:
Identification of the module using a diagnostics tool.
Green and yellow flashing
synchronized:
Exception status; error in firmware.
Yellow on:
DP slave mode.
Yellow off:
Not DP slave mode.
Yellow flashes at one second intervals:
Error in DP slave mode.
CP 5612
12
Operating Instructions, 12/2012, C79000-G8976-C278-02
Software installation
2.1
2
Installing the SIMATIC NET PC software
SIMATIC NET PC software
The SIMATIC NET PC software is one of several software packages with which you can
operate the CP in your PG/PC. You will find information on alternatives in the section
"Alternative software packets (Page 14)".
To configure the CP, you require additional configuration software. You will find information
on the configuration software in the section "Configuration (Page 19)".
Condition
The plug and play function is activated in the BIOS of your PG/PC.
Prior to hardware installation
Install the software as described in the installation manual "SIMATIC NET PC Software".
You will find this installation manual on the Product Support pages under the entry ID:
Auto-Hotspot (http://support.automation.siemens.com/WW/view/en/61630923)
You should also note the current information on the SIMATIC NET PC software on the
Product Support pages:
Support (http://support.automation.siemens.com/WW/view/en/10805995/133400)
After the hardware installation
After installing the CP, your PG/PC automatically searches for a suitable driver.
1. Follow the instructions of the Hardware Wizard of Windows.
2. Do not activate the search for drivers on the Internet.
2.2
Uninstalling the SIMATIC NET PC software
Condition
The SIMATIC NET PC software is installed on the PG/PC.
CP 5612
Operating Instructions, 12/2012, C79000-G8976-C278-02
13
Software installation
2.3 Alternative software packets
Procedure
Note
The procedure recommended here deletes the entire SIMATIC NET PC software on the
PG/PC not only the driver for the communications processor.
Uninstall the entire software package as described and recommended in the installation
manual "SIMATIC NET PC Software".
You will find the installation manual on the SIMATIC NET DVD or on the Product Support
pages under the following entry ID:
61630923 (http://support.automation.siemens.com/WW/view/en/61630923)
2.3
Alternative software packets
Alternatives to SIMATIC NET PC software
To operate the CP, alternative software packages such as STEP 7 V5.5 or STEP 7
Professional V11 are also available. You will find current information on this on the Product
Support pages under the following entry ID:
47071380 (http://support.automation.siemens.com/WW/view/en/47071380)
CP 5612
14
Operating Instructions, 12/2012, C79000-G8976-C278-02
Hardware installation
3.1
3
Safety notices
WARNING
Electric shock possible - work only when the power supply is off
Opening the PG/PC and plugging or pulling the communications processor is permitted
only when the power is off.
Turn off your PG/PC and pull the power cable connector before you start the hardware
installation.
NOTICE
Note the EC directives
Components can be damaged or destroyed by electrostatic discharge. When installing,
keep to the rules for electrostatically sensitive devices (ESD).
• Pick up components and modules only by their edges. Do not touch the pins or
conductors.
• Before opening the PG/PC, make sure that you discharge any electrostatic charge from
your body. You can do this by touching metal parts on the back panel of the PG/PC
pulling the power plug.
• Make sure that you also discharge any electrostatic charge from tools you intend to use
for the work on the PG/PC.
• Do not operate the PG/PC with the housing open.
NOTICE
Firm mounting
The CP must sit firmly and uniformly in the slot. Check that the module sits firmly in the slot
as described in the manual accompanying your PG/PC.
Note
Oblique installation position is permitted
Some PG/PC designs require oblique installation of the CP. This is permitted.
CP 5612
Operating Instructions, 12/2012, C79000-G8976-C278-02
15
Hardware installation
3.2 Installing hardware
3.2
Installing hardware
Permitted number of communications processors in the PG/PC
The driver software supports a maximum of 2 CPs per PG/PC, of which a maximum of 1 CP
may be in configured mode.
Automatic adaptation of the bus clock speed
The CP is designed for a bus clock speed of 66 MHz. If the CP is inserted in a PCI slot with
a higher bus clock speed, the bus clock speed is adapted to the highest possible bus rate of
the CP. Examples:
● The PCI slot is automatically reduced to a bus clock speed of 66 MHz.
● The bus clock speed of the CP is automatically reduced to 33 MHz if a module with a 33
MHz bus clock speed is connected.
Procedure
Note
• First install the software
First install the software before you insert the CP in the slot.
• Activated plug and play function
The plug and play function must be activated in the BIOS of your PG/PC.
Follow the steps outlined below when inserting the CP:
1. Turn off your PG/PC and pull the power cable connector.
2. Open the computer housing as described in the manual accompanying your PG/PC.
3. Remove the cover of a free PCI slot.
4. Remove the CP from its packaging.
5. Insert the CP in the PCI slot and secure it.
Make sure that the CP is correctly inserted and secured.
6. Close the computer housing as described in the manual accompanying your PG/PC.
7. Insert the power plug into the socket again and turn your PG/PC on.
The plug and play function of Windows automatically searches for a driver.
8. Follow the instructions of the Hardware Wizard of Windows.
Do not activate the search for drivers on the Internet.
CP 5612
16
Operating Instructions, 12/2012, C79000-G8976-C278-02
Hardware installation
3.3 Hardware compatibility
3.3
Hardware compatibility
Compatibility with other CPs
The CP 5612 can replace the following CPs:
● CP 5621
● CP 5611 A2
● CP 5611
Note
PCI module
Please note: The CP 5612 is a PCI card. The CP 5621, on the other hand, is a PCI Express
card. This means that you can only replace a CP 5621 with a CP 5612 if there is a PCI slot
available on the PG/PC.
Note
If the previous CP has been removed from the PG/PC, no configuration changes need to be
made
You can adopt the configuration of the previous CP. To do this, you simply need to reload
the configuration.
Note the following: When loading the previous configuration, the previous CP has priority
over the new CP. As long as the previous CP is connected, its configuration cannot be
adopted by the new CP. You should therefore remove the previous CP from your PC/PG.
Procedure for replacement
When replacing a module, follow the steps described in the section "Hardware installation
(Page 15)".
CP 5612
Operating Instructions, 12/2012, C79000-G8976-C278-02
17
Hardware installation
3.3 Hardware compatibility
CP 5612
18
Operating Instructions, 12/2012, C79000-G8976-C278-02
Configuration
4
Configuring with STEP 7 or NCM PC
Create a suitable configuration for the CP in STEP 7 or NCM PC.
the procedure is described in detail in the configuration manual "Commissioning PC
Stations“. You will find this document on the Product Support pages under the following entry
ID:
13542666 (http://support.automation.siemens.com/WW/view/en/13542666)
Compatibility during configuration
If there is not yet a CP 5612 in the hardware catalog of your STEP 7 version or NCM PC
version, you can select a CP 5611 A2 or CP 5611 for configuration. The CP 5612 is
downwards compatible with the configurations of the previous versions.
CP 5612
Operating Instructions, 12/2012, C79000-G8976-C278-02
19
Configuration
CP 5612
20
Operating Instructions, 12/2012, C79000-G8976-C278-02
5
Technical specifications
Technical specifications of the CP 5612
Connection to PROFIBUS
Amount
1
Transmission speeds
9.6 kbps, 19.2 kbps, 45.45 kbps,
93.75 kbps, 187.5 kbps, 500 kbps,
1.5 Mbps, 3 Mbps, 6 Mbps, 12 Mbps
Design
9-pin D-sub female connector with screw
locking mechanism
RS-485 (ungrounded within the SELV
limits)
Properties
Grounded cable shield
Floating interface signals
Connection to PG/PC
PCI, 33 MHz / 66 MHz, 32 bit
signal voltage: 5 VDC or 3.3 VDC
V 2.2 plug and play
Electrical specifications of the PCI plug-in connector
Operating voltage
Rated voltage
Permitted range
3.3 VDC and 12 VDC
3.0... 3.6 VDC for 3.3 VDC
11.0...13.0 VDC for 12 VDC
Current consumption
Effective power loss
Properties
Safety extra low voltage (SELV) to EN
60950
Typical for 3.3 V
150 mA
Typical for 12 V
250 mA
Typical
3.5 W
Temperature
(EN 60068-2-1+2)
+5...+50°C
Temperature change max.
≤10 K/h
Rel. humidity
(EN 60068-2-78)
≤ 85% at 30°C no condensation
Rapid temperature change
(EN 60068-2-14)
+5...+50°C, 5 cycles
Permitted ambient conditions
Operating conditions
Storage and transportation conditions Temperature
(EN 60068-2-1+2)
-20...+60°C
Temperature change max.
≤20 K/h
Rel. humidity
(EN 60068-2-78)
≤ 95% at +25...+55°C no condensation
CP 5612
Operating Instructions, 12/2012, C79000-G8976-C278-02
21
Technical specifications
Technical specifications of the CP 5612
Fast temperature change
•
to EN 60068-2-14
-20...+60°C, 2 cycles
•
to EN 60068-2-30
+25...+55°C at 95% humidity
Vibration, operating
(EN 60068-2-6)
Frequency 10...58 Hz
Frequency 58...500 Hz
number of cycles
0.075 mm amplitude
10 m/s2 Acceleration
10/axis
Shock, operating
(EN 60068-2-27)
Half sine
Time
Number of shocks
50 m/s2 (5 g)
30 ms
100/axis
Design, dimensions and weight
Module format
Flat module
Short PCI card
Weight
98 g
Dimensions (W x H x D)
18 x 107 x 125 mm
Electromagnetic compatibility
Emission
Immunity
•
to EN 55022
Class B
•
to FCC
Class B
On signal cables
•
Surge to EN 610004-5
±2 kV
•
Burst to EN 61000-4-3
±2 kV
to discharge of static electricity
•
Contact discharge to IEC 610004-2
±6 kV
to radiated radio frequencies
•
to EN 61000-4-3
•
to EN 61000-4-6
10 V/m at 80 MHz to 2 GHz
10 V/m, 50% ON duration at 900 MHz and
1.89 GHz
10 V/m, 80% amplitude modulation at 1
kHz, 10 kHz to 80 MHz
CP 5612
22
Operating Instructions, 12/2012, C79000-G8976-C278-02
A
Approvals
Note
The specified approvals apply only when the corresponding mark is printed on the
communications processor.
Electromagnetic compatibility - EMC directive
The communications processor meets the requirements of the EC Directive:2004/108/EEC
(EMC directive).
The communications processor is designed for use in the following areas:
Area of application
Requirements
Emission
Immunity
Residential areas, business and commercial
operations, and small businesses
EN 61000-6-3
EN 61000-6-1
Industrial environment
EN 61000-6-4
EN 61000-6-2
EC declaration of conformity
You will find the EC declaration of conformity for this communications processor on the
Product Support pages under the following entry ID:
63367995 (http://support.automation.siemens.com/WW/view/en/63367995)
Machinery directive
This communications processor is not a machine in the sense of the EC directive
2006/42/EEC (Machinery Directive). There is therefore no declaration of conformity relating
to this EC Directive for the communications processor.
If the communications processor is part of the equipment of a machine, it must be included in
the procedure for obtaining the declaration of conformity by the manufacturer of the machine.
C-TICK approval
The communications processor meets the requirements of the Australian AS/NZS 3548
standard.
CP 5612
Operating Instructions, 12/2012, C79000-G8976-C278-02
23
Approvals
CSA approval
The communications processor has an approval in accordance with the Canadian CAN/CSA
C22.2 No. 60950-1 standard.
ICES conformity
The communications processor meets the requirements of the Canadian standard ICES-003.
It is rated as a digital device of Class B ("Class B digital apparatus").
FCC approval
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
● Consult the dealer or an experienced radio/TV technician for help.
Siemens AG is not responsible for any radio television interference caused by unauthorized
modifications of this equipment or the substitution or attachment of connecting cables and
equipment other than those specified by Siemens AG. The correction of interference caused
by such unauthorized modification, substitution or attachment will be the responsibility of the
user. The use of shielded I/O cables is required when connecting this equipment to any and
all optional peripheral or host devices. Failure to do so may violate FCC and ICES rules.
UL approval
The communications processor has an approval in accordance with the US standard
UL 60950-1.
CP 5612
24
Operating Instructions, 12/2012, C79000-G8976-C278-02
Index
O
B
Oblique installation position, 15
Bus clock speed, 16
P
C
Compatibility, 17, 19
Components of the product, 3
Configuration compatibility, 19
Converting, 17
CP 5611, 17
CP 5611 A2, 17
CP 5621, 17
D
Documentation on the Internet, 3
D-sub female connector, 11
PIN assignment, 11
PROFIBUS network, 10
R
Replacing, 17
S
SIMATIC NET documentation, 4
SIMATIC NET glossary, 5
STEP 7, 14, 19
E
Electric shock, 15
Electrostatic charge, 15
ESD directives, 15
G
Glossary, 5
L
LEDs, 11
M
Mounting, 15
N
NCM PC, 19
Number of CPs, permitted, 16
CP 5612
Operating Instructions, 12/2012, C79000-G8976-C278-02
25
Index
CP 5612
26
Operating Instructions, 12/2012, C79000-G8976-C278-02
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement