Operating Instructions

Operating Instructions
TAIWAN
NO.TGM-M1G-AEG-WNB-NCM
TYPE I AEG
LENGTH I 1103 mm
WEIGHT I 3650 g
MAGAZINE I 20 Rounds
RECEIVER I Metal
BEARING I 8 mm
INNER BARREL I 510 mm
BLOW BACK I NO
VELOCITY I According to Local Regulation
ChangHua Tel : +886-4-798-9000 Fax : +886-4-798-9900
(Head Quarter) No.999, Zhonghua Rd. Shengang Township,
Changhua County 50952, Taiwan (R.O.C.)
Taipei Tel : +886-2-2692-2000 Fax : +886-2-2692-4000
11F-3., No.27, Lane 169, Kangning St. Shijr City,
Taipei County 22180, Taiwan (R.O.C.)
Sales Dept. [email protected], [email protected]
Technology Dept. [email protected]
PR Dept. [email protected]
U.S.A.
Los Angeles Tel : +1-626-581-0101
Fax : +1-626-581-1011
1122 Coiner Court City of Industry,
CA 91748 (U.S.A.)
[email protected]
G2-201403-02-英
• Stop shooting when the battery power is low.
• Do not adjust the motor without authorization or by certified technician.
For maintenance, use the silicon oil on the air nozzle,
• do
not use other types of corrosive oil.
Operating Instructions
All G&G products are complied with CE and ROHS 2.0.
G&G Armament is also certified manufacturer of ISO 9001.
Operating Instructions
supervision required. Always wear safety goggles when using this product.
• Adult
or careless handling of this product may cause injury.May be hazardous up
• Misuse
to 50 meters.
product is intended for users 18 years or older.Read all instructions before using this product.
• This
buyer and the user of this product shall adhere to all local laws regulating the usage and the
• The
ownership of airsoft guns.
You may be liable for
damaging public or personal
property or for injuring a
person or an animal. Always
observe goodmanners and
enjoy fun sport shooting.
When you carry the air gun,
attach the safety cap,set the
selector lever to the safety
position and always put the
air gun in a case or bag.
Safety procedures :
1. Attach the safety cap to the
muzzle.
2. Set the selector lever to the
safety position.
3. Remove the magazine.
4. Remove the battery.
Select a safe place for
operating the air gun, and
avoid places where people
and cars are around.
Looking into the muzzle is
extremely dangerous!
Regardless if BB's have been
loaded or not. If you get hit in
the eye by a BB, you may in
worst case, lose your eye sight.
Always attach the safety
cap to the muzzle, remove
the battery, and store the
air gun in a case or bag
and at a place that is out of
reach of children.
There may be cases where
some BB’s remain in the gun
after the magazine has been
removed. After removal of the
magazine, direct the muzzle
towards a safe direction and pull
the trigger to confirm there are
no BB's that remain in the gun.
Set the selector lever to safety,
then attach the safety cap.
When shooting the air target
practice or in a game situation,
you and all participants must
wear safety goggles or other
eye protective gear.
Also, pay attention to ricochets.
It is very important to pay
attention to third parties other
than the participants.
01
Warning
Never direct the muzzle
towards a person or animal.
This may cause harm or
serious injury if an accident
was to occur.
Operating Instructions
Make sure to always put the
safety cap on the muzzle when
you are not shooting. Do this to
prevent accident,discharge of
BB’s and also for dust
protection purposes.Never pull
the trigger while the safety cap
is attached to the muzzle.
Activating the trigger carelessly
is extremely dangerous.Never
put your finger on the trigger
unless the safety cap is removed
and you are ready to shoot a
target.
Disassembling or modifying the
gun may adversely affect the
performance of the gun and be
dangerous. It also may Void the
warranty and in some areas it
might be against the Law.
Warning
02
Operating Instructions
[ Safety mode setting ]
Rear Sight
Front Sight
Outer Barrel
Rear handguard
Magazine Catch
Elevation Adjustment Knob
[ Contents ]
Flash Suppressor
make sure that
•theAlways
muzzle points into a safe
Front handguard
03 CONTENTS
Windage Adjustment Knob
03 COMPONENTS
04 BATTERY SETTING
Upper Receiver
Trigger
Butt Swivel
Bolt
04 SAFETY MODE SETTING
[ FIRE ]
Magazine
01 WARNING
[ Battery setting ]
Step 1
Bolt Handle
Butt Plate
[ SAFE ]
direction.
• Use only the G&G battery purchased from your local dealer.
Step 3
Switch on safety.
Connect the battery and
insert into the stock.
Step 2
Step 4
Open the battery cover.
Close the battery cover.
05 LOADING THE MAGAZINE
06 REAR SIGHT ADJUSTMENT
06 BOLT HANDLE /
HOP-UP ADJUSTMENT
07 FIRING / MAINTENANCE
08 TROUBLE SHOOTING
09 PARTS LIST
03
Swivel Stacking
Safety
Trigger Guard
Cleaning Rod
Contents / Components
Swivel Stock Ferrule
Bayonet Lug
Protective Cap
Operating Instructions
Safety mode setting / Battery setting
04
Operating Instructions
[ Loading the magazine ]
It is strongly recommended to only use G&G BB pellets. Using low quality BB pellets will damage your
Only use flawless BBs.
Do not use the following BBs.
airsoft gun and void product warranty.
•
1 Diameter larger than 6mm.
ø 6mm
3 Both halves not aligned.
Step 1
[ Rear sight adjustment ]
•
2 With ridges or cracks.
[ ELEVATION ADJUSTMENT KNOB ]
4 Used, soiled.
5
Step 2
Lock
Unlock
2
4
Down
1
Up
[ WINDAGE ADJUSTMENT KNOB ]
1. Pull and turn the knob to
adjust the sight.
2. Turning clockwise :
To correct high shots.
Turning counter-clockwise:
To correct low shots.
2
Right
Left
1
1. Pull and turn the
knob to adjust the sight.
2. Turning clockwise :
To correct the shots
leaning to the left.
Turning counterclockwise:
To correct the shots
leaning to the right.
1
Open
2
[ Bolt Handle & Hop-up Adjustment ]
Press the magazine release to remove the magazine.
Hop
Step 3
Insert the magazine into the rifle.
05
•
Never hold the gun sideways as the BB pellets will
curve right or left. This is due to the HOP-UP system.
Loading the magazine
1. Open the trap door on
the top of the BB loader.
2. Load G&G 5.95mm BB
pellets into the Magazine
style BB Loader.
3.Connect magazine style
loader with the 20R Magazine.
4. Slide the retainer to release the injection lever.
5. Press the injection lever to load BBs into the
magazine. Continue loading until the magazine is full.
Normal
3
Too much HOP-UP.(Return the lever toward NORMAL)
Best direction.
Pull the bolt handle backwards.
Turn hop-up dial to adjust to the BB pellets' ideal flight pattern.
The hop-up dial can only be turned a certain amount.
Turning too much will damage the unit.
Magazine Style 420R BB Loader [ Optional Parts ]
Operating Instructions
Not enough HOP-UP.(Move the lever toward HOP.)
Or too much HOP-UP.(Return the lever toward NORMAL.)
• Be careful not to catch your fingers in the dummy bolt.
Rear sight adjustment
06
After Operation
Operating Instructions
[ Firing ]
the magazine, direct the muzzle into a safe direction then fire the gun
• inRemove
semi-auto mode for a few shots. Switch on safety.
Always disconnect the battery and attach the protective cap
• whenever
you do not operate the air gun.
SYMPTOM
2
1
Step 1
Step 2
Step 3
No operation at all
3
Make sure insert the magazine upwards and into the rifle
until it clicks.
Remove the protective cap only when you are ready for
firing the gun.
Switch off safety and you are now ready to fire.
Make sure no dirt gets into the
chamber to avoid clogging of BB
pellets. The hop up may take 200
to 300 rounds to remove the
excessive silicone oil, this is the
normal operation fo the gun.
•
If BB pellets are clogged, remove them and apply a few drops of G&G silicone oil into the chamber
When BB pellets
are clogged
from the magazine entrance. Apply G&G silicone oil for 0.5 to 1 sec, to obtain smooth continuous firing.
[ Maintenance ]
1
2
07
1. Before you clean the inner barrel, make
sure the hop up is turn to normal position.
2. Take a piece of cotton cloth about 1 inch
by 0.5 inch and insert one end of the cloth
into the hole of the tip of cleaning rod and
wrap it around the tip.
3. Apply a drop of silicone oil or Teflon oil on
the cloth and insert the cleaning rod into
inner barrel.
4. Check the cloth and repeat above steps
until no dirt on the cloth.
Firing / Maintenance
[ Trouble shooting ]
Although motor is revolving,
no pellet can be fired
POTENTIAL
Selector lever is set to safety.
Set the selector lever to Semi.
Battery is not charged.
Charge the battery.
Battery connector is disconnected.
Connect the connector.
The
Connect the connector correctly(check the fuse)
and
of battery connector is reverse.
Expired motor life (50,000 to 60,000 rounds) or poor
electrical connection.
Replace the dead motor (can be purchased from local dealer or
directly G&G). Check and repair the contacts.
Pellets are clogged inside the magazine.
Insert the charging rod into the magazine and move up and down a
few times to remove clogged pellets.
Pellets are clogged in the chamber.
Remove clogged pellets using the cleaning rod.
Faulty gear.
Pruchase the replacement gear from your dealer or G&G and repair.
Damaged or worn chamber set.
Never use CRC-556, WD40
or other corrosive lubricant.
Damaged or worn piston set (O-ring,piston spring).
Shooting distance becomes
shorter
CORRECTIVE
Replace the replacement parts(Purchasing from your dealer or G&G).
Something is jammed in the inner barrel.
Use the cleaning rod and clean the inner barrel.
Faulty BB pellets (too small or heavy).
Use the genuine G&G Pellets.
Shrotage of silicone oil.
Drops few drops of silicone oil from upper the chamber.
Gear problem caused by too many blank firing.
Too loud operating noise
1.Return the hop up dial to the Normal position and insert the
cleaning rod from the lead edge of the barrel.
2.To remove clogged BB’s, carefully insert the cleaning rod
inside the barrel with the flat tip facing down as shown below.
Pellets being fallen out from
barrel end
If gun gets wet
Operating Instructions
Worn or damaged gear.
Gear problem caused by too many blank firing.
Consult your dealer or G&G for overhaul maintenance, part
replacement (gear,etc.) or repair.
Damaged or worn chamber set.
No hop setting.
Turn the hop adjustment lever toward Hop.
Faulty BB Pellets (too small or heavy).
Use the G&G Pellets.
Stop operation immediately, disconnect the battery, wipe off water from inside the main body and the battery. After
completely dry, carry out trial firing. If the unit is not operational, please contact your local dealer for repair.
Trouble shooting
08
Operating Instructions
M1
Rear handguard retainer
M1G - 02
Front barrel set
M1G - 03
Bolt handle set
M1G - 04
Trigger set
M1G - 05
Front handguard set
M1G - 06
Rear handguard set
M1G - 07
Stock set
M1G - 08
Gear box set
M1G - 09
Motor set
M1G - 10
Dummy Bolt Plate
M1G - 11
Upper receiver set
M1G - 12
Inner barrel
M1G - 13
Outer barrel set
M1G - 14
Rear sight set
M1G - 15
Hop-up set
M1G - 16
Bolt handle spring set
M1G - 17
Stock Plate Set
M1G - 18
Magazine
09
Parts list
2
6
7
[ Parts list ]
M1G - 01
11
G-
5
4
M
3
1G
2
14
5
5
M
1G
2
M1
G
M1
8
5
2
G
M1
6
2
G
2
1
3
4
5
6
4
7
6
3
M1
2
3
07
G1
18
M
G1
M
4
M1
E-Mail:
[email protected]
M
1G
02
4
5
6
5
1
7
M1
17
G-
G
1
2
3
2
1
-16
-05
1
-13
-01
The grouped parts may all be purchased
from the G&G Support Department.
3
2
1
2
G
M1
2
G
M1
3
2
-06
1
7
3
1
15
G-
11
9
12
3
2
7
12
4
8
4
3
6
1
1
04
G-
10
2
9
8
1
1
7
6
1
M1
3
1
4
M
1G
-10
•
•
-09
4
5
6
1
11
10
8
6
G
M1
-08
9
7
1
2
3
7
3
G
M1
5
Operating Instructions
Parts list
10
-03
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement