Users Manual - Electric Heating
Users Manual
Aluminium Radiator
HYBC-4G, HYBC-7G, HYBC-11G
Please read this manual carefully before use
IMPORTANT SAFEGUARDS
When using an electrical appliance, basic safety precautions should
always be observed, including the following:
READ ALL INSTRUCTIONS BEFORE USING
WARNING: To reduce the risk of fire, electrical shock, or injury
to person:
1. The product is for household use only.
2. Connect the appliance to single-phase AC supply of the voltage
specified on the rating plate.
3. In order to avoid overheating do not cover the heater.
4. Never leave the heater unattended while it is in use. Always turn the
product to the OFF position and unplug it from the electrical outlet when
not in use.
5. Extreme caution is necessary when any heater is used by or near
children, invalids or elderly person and whenever the heater is left
operating and unattended.
6. The heater must not be located immediately below an electrical
Socket-outlet.
7. Do not run cord under carpeting and do not cover cord with throw rugs,
runners or the like. Arrange cord away from traffic area and where it will
not be tripped over.
8. Do not operate the heater with a damaged cord or plug, or after the
heater malfunctions, has been dropped, or damaged in any manner.
9. If the supply cord is damaged, it must be replaced by the manufacturer,
its service agent or a similarly qualified person in order to avoid a hazard.
10. Avoid the use of an extension cord as this may overheat and cause a
risk of fire.
11. Use the heater in a well-ventilated area. Do not insert or allow objects
to enter any ventilation or exhaust opening. To prevent a possible fire, do
not block air intakes or exhaust openings in any manner. Do not use on
soft surfaces, like a bed, where openings may become blocked. Use the
heater on flat, dry surfaces only.
12. Do not place this heater near flammable materials, surfaces or
substances, as there may be a risk of fire. Keep the above flammable
materials, surfaces or substances at least 1m from the front of the product
and keep them away from the sides and rear.
13. Do not use the heater in any areas where petrol, paint or other
flammable liquids are stored e.g. Garages or workshops as a hot, arcing or
sparking parts inside the heater.
14. Don’t use this heater in the immediate surroundings of a bath, a
shower or a swimming pool with floor standing mode. Never locate the
heater where it may fall into bathtub or other water container.
15. Never touch the heater with wet hand. The heater should be installed
so that can not be touched by a person using a bath or shower.
16. This heater is hot when in use. To avoid burns and personal injury, do
not let bare skin touch hot surfaces.
17. Before moving the heater, please must unplugged it and let it cool
down for 15 minutes. If provided, use handles when moving the product.
18. Be sure that no other appliances are in use on the same electrical
circuit as your product as an overload can occur.
19.This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for
their safety.
20.Children should be supervised to ensure that they do not play with the
appliance.
21. This heater is filled with a precise quantity of special oil.
22. Repair requiring opening of the oil container are only to be made by
the manufacturer or his service agent who should be contacted if there is
an oil leakage.
23. Regulations concerning the disposal of oil when scrapping the
appliance have to be followed.
FOR HOUSEHOLD USE ONLY
SAVE THESE INSTRUCTIONS
SPECIFICATIONS
MODEL NO
FINS
NET SIZE
RATED VOLTAGE
RATED POWER
HYBC-4G
HYBC-7G
HYBC-11G
4
7
11
490X590X80mm
730X590X80mm
1050X590X80mm
~240V/50Hz
~240V/50Hz
600W
1200W
~240V/50Hz
1800W
STRUCTURE AND PARTS
CHARACTERISTIC
1.
1 heat setting
2.
Over heating protection
3.
With digital LCD
4.
Room temperature setting
5.
Room temperature sensor
6.
Digital clock, digital week calendar
7.
Multi-running mode:
daily program mode, weekly program mode, free use mode, pilot
system function
8.
Anti-frost function
9.
Wall-mount use
INSTALLATION
Used as wall-mounted:
(1) Drill holes on the wall according to the picture.
Warning: Be sure to keep the distance between the heater
and floor, wall and so on accordingly.
(2) Fit the fasten tube in the holes.
(3) Fit the up-hook on the wall with screws.
(4) Hang the unit on the up-hook.
(5) Fit the bottom hook between 2 fins at the bottom of unit.
(6) Fasten he bottom hook with screw.
The distance of hanging hole is as follows:
Fins
4
7
11
L(mm)
160
400
720
Warning:
: Before using the heater make sure that it is mounted
tightly on the wall. Damage may occur if it is placed on an incline
or decline.
INSTRUCTIONS FOR USE
Warning:
: Before using the heater make sure that it is mounted
tightly on the wall. Damage may occur if it is placed on an incline
or decline.
The control system is with following functions:
1. With digital LCD to let you know the working situation of the unit.
2. Room temperature setting to enable you to set the desired room
temperature.
3. Room temperature sensor to control the heating of the unit according
to your desired room temperature.
4. Digital clock, digital week calendar.
5. Multi-running mode:
daily program mode, weekly program mode, free use mode
6. Anti-frost function
Control panel and LCD screen
Control panel:
There are total 5 buttons on the control panel as follows:
------Power stand by switch
------Date and time settings; Timer settings; Shift the working mode
------Select running mode;
Set program;
------Increasing;
------Decreasing;
Screen:
Clock,
Date,
Program name,
Target temperature,
Anti-frost,
Comfort,
Stand by,
program setting,
solid time mark
timer,
Economic,
buttons lock,
heating,
program contents,
Rationale:
There are 3 running modes: free
weekly
, daily
~
and
.
Free use mode(
Daily mode(
): It will include normal mode and timer mode
~
program is combined with
economic(
;
): There are total 9 daily programs. Every
3 working modes: comfort(
and )and anti-frost(
and ),
and empty).
every day(24hours) is divided into 24 segments evenly. Every segments
will be filled in with one working mode to combine a daily program. All the
setting for daily program will be kept in memory by the unit. If a daily
program is selected, the unit will repeat this program every day.
Weekly mode:
Selecting one daily program ( from daily programs P1-P9) for every day in
a week to combine a weekly program.
How to use:
1. Plug and switch on the unit. For the first time use, the screen will
showed as follows:
Press
,then
disappeared and unit get into free normal
mode(note: units always get into free normal mode from stand by
mode).
2-1.Free program:
For the first time use, the screen will showed as follows:
2-1-1.Time setting:
Press
,the hour start to twinkle, use
or
to select hour (0 ~ 23).
again, the minutes start to twinkle, use
Press
minute( 0 to 59); Pressed
or
to select
again, date start to twinkle, use
(1-Monday, 2-Tuesday, 3-Wednesday,
4-Thursday, 5-Friday, 6-Saturday, 7-Sunday); Finally press
or
to select date
to confirm and finish the setting.
(Note: If press
or
without releasing, you can achieve rapid
increasing or decreasing;
If there is no pressing, the twinkle would stop after 5 seconds and setting
will be finished automatically.)
2-1-2. Temperature setting:
Press
or
to set the target temperature directly and at this
moment the temperature starts to twinkle. Press
or
to set the
target temperature. Temperature adjustable range is from 10 ℃ ~ 35 ℃.
(Note: If press
or
without releasing, you can achieve rapid
increasing or decreasing;
If there is no pressing, the twinkle would stop after 5 seconds and setting
will be finished automatically.)
2-1-3.Timer setting(timer mode):
Long-press
(3 seconds) till the
showed. Same time the clock will
turn to 00:00 and start to twinkle. This means the timer setting starts (as
following):
Press
or
to set the timer length by every press with half an hour
(30 minutes). The maximum timer length is 24 hours.
When the timer is over, the unit would enter into standby mode
(Note: If press
or
.
without releasing, you can achieve rapid
increasing or decreasing;
If there is no pressing, the twinkle would stop after 5 seconds and setting
will be finished automatically.)
You can also set time and temperature same as 2-1-1 and 2-1-2.
Quit from timer mode: long press button
(3 seconds) until the
disappeared. The unit automatically return back to free normal mode.
(Note: Once the machine exit free program (enter the day, week program,
or standby), and then return to the free program, the unit always enters
into the free normal mode first. The original timing model was
automatically canceled).
2-2.running mode selecting:
Press
to get into program selecting (Program No. start to twinkle).
Pressed
then press
or
to select running mode (
-
~
-
)and
to confirm it . The unit would run following the new
selection program.
Note: During this period, if there is no pressing, the selection is
automatically completed 5 seconds later.
2-3. Day program
Day program has three kinds of working modes:
Comfort mode :(
and program content displayed
), adjustable
range from 10 ℃ ~ 35 ℃;
Economic mode: (
and program content displayed
), adjustable
range of 10 ℃ ~ 35 ℃; the temperature should no higher than
comfortable temperature;
Anti-frost mode: (
and program content displayed empty ), 7 ℃,
it’s inherent and non-adjustable.
If a daily program was chosen for the work program, the unit will
repeat the program every day.
Different program used for the first time as follows:
P1:
P2:
P3:
P4:
P5:
P6:
P7:
P8:
P9:
2-3-1. Time setting:
Same as 2-1-1, then the unit will automatically adjust to the current
time and running accordingly.
2-3-2. Temperature setting:
Long-press
(3 seconds) until
twinkle, at the same time the
original comfort temperature start to twinkle. Press
target comfort temperature. Press
,
to set the
to confirm, and
start to
twinkle, the original economic temperature also starts to twinkle.
Press
,
to set the target economic temperature. Use
to
confirm it temperature setting is completed, the unit come back to run
under comfort mode.
The temperature will be kept into the memory.
(Note: During this period, if there is no pressing, the settng is
automatically completed 5 seconds later.)
2-3-3. Setting Daily program:
Press
to choose the program (from
set. Then long-press
this time
~
) which you want to
(3 seconds) to enter the program settings, at
displayed on the screen (
will showed until the
setting is completed, the heating will stop during the setting). The date
does not show , time is 00:00. The mark
starts to twinkle rapidly at the
first segment of selected program, such as following (when the selected
daily program is P1):
Press
to select the working mode (
, for comfort;
, for the
economic;
, empty for the anti-frost), then Press
(forward),
(back) to copy the mode into every segment(press without releasing can
achieve fast-forward or fast-back). Finally press
program content and exit program setting.
to confirm the
Disappear; the unit
comes back to normal work.
Note: daily program setting, the hour will go ahead or return back
according to the mark.
Settings can be terminated at any time during setting. The new content
will be retained.
the new program will be kept into the memory and replace the original
program.
2-4. Week program:
You may select week program according 2-2. the first use as following:
2-4-1.
.Time setting
Same as 2-1-1, then the unit will automatically adjust to the current
time and running accordingly.
2-4-2.
.Temperature setting:
:
Same as 2-3-2
2-4-3. Setting weekly program:
Long-press
(3 seconds) to enter weekly program setting, the time
and working mode are no longer displayed,
showed (
displayed
until the setting finished, the unit stopped heating during the setting),
Monday marking begin to twinkle, program name of Monday also twinkl
(corresponding program content also shows). The screen is as follows:
Press
Press
,
to select the daily program from P1~P9 for Monday (1).
to confirm and automatically enter the Tuesday (2).With same
method you can select a daily program for everyday in a week . Finally
press
to complete week program settings. Then
Disappear
and the unit will run according to new weekly program.
Note: Settings can be terminated at any time during setting. The new
content will be retained.
3, Factory pre-setting:
The unit is with a factory pre-setting as follows:
Date: 1 (Monday) clock: 00:00
Anti-frost: 7 ℃
Free mode temperature: 10 ℃
Daily program Temperature: Comfort: 22 ℃ economy: 17 ℃
Weekly program : 1 ~ 5 (Mon-Fri): P1
6 (Saturday): P2
7 (Sunday): P3
Note: Press
to power on, the unit would come back to factory
pre-setting.
4. Other notes:
:
(1) The screen is with back light. It will extinguish after 1 minute if you
didn’t press any button. It will light up if you press any button.
(2) Unit is with button lock function. The buttons will be locked (
after 1 minute if you didn’t press any button.
Open lock: press
and
at same time.
)
(3) Time will be clean to 00:00 if you unplugged unit or cut off the
power.
(4) This heater includes an overheat protection system that shuts off
the heater when parts of the heater are getting excessively hot.
will showed only the unit is heating.
(5)
(6) The units will always get into free normal mode from standby
mode;
The unit will return to latest running mode due to suddenly
power off after power come back.
MAINTENANCE
1. Always remove the plug from the socket-outlet and allow the heater to
cool down before clean it.
2. Wipe the exterior surface of the heater occasionally with a soft damp
cloth (not dripping wet) and dry the exterior surface before operating the
heater.
WARNING:
Do not immerse the heater in water.
Do not use any cleaning chemicals such as detergents and
abrasives.
Do not allow the interior to get wet as this could
create a hazard.
3. Light accumulated may be removed from the heater with a soft dry
cloth.
4. To store away the heater, put the heater back into its original package
and store it in a clean dry place.
5. In case of malfunction or doubt, do not try to repair the heater yourself,
it may result in a fire hazard or electric shock.
CONFORMITY WITH DIRECTIVES
This product is CE marked to denote conformity with Directives 73/23/EEC
(Low Voltage) and 89/336/EEC (Electromagnetic Compatibility), as
amended.
Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist. Check
with your Local Authority or retailer for recycling advice.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement