Archer C20_V1_QIG - TP-Link

Archer C20_V1_QIG - TP-Link
INTERNET
Quick
Installation Guide
Modem
7106505035 REV1.0.0
AC750 Wireless Dual Band Router
20
Typical Connection
1. Connect the Hardware
1
2
Power off the modem,
and remove the backup
battery if any.
3
Connect the modem to the
Internet port on your router with
an Ethernet cable.
4
Power on the modem,
wait for 2 minutes and
then power on the router.
Check the following LEDs to
ensure the hardware connection
is correct.
LAN
Power Off
Power On
INTERNET
INTERNET
INTERNET
Power
2.4G
5G
Internet
On
On
On
On
Power On
Note: If your Internet comes via an Ethernet cable from the wall instead of any DSL/Cable/Satellite modems, please connect the Ethernet cable directly to the router’s Internet port.
2. Configure the Router
Method 1 Via Web Browser
1
Connect your computer to the router (Wired or Wireless).
Wired
Wireless
Or
Ethernet cable
2
a
Connect wirelessly by using
the default network name
(SSID) and password printed
on the product label at the
bottom of the router.
AC750 Wireless Dual Band Router
Model: C20
Power: 12V
1A
Default Access:http://tplinkwifi.net
Serial
Number
C20
1.0
MAC
Address
FCC ID:TE7C20
5734
IC:8853A-C20
Wireless
Password
/PIN
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
SSID
SSID:TP-LINK_XXXX
SSID:TP-LINK_XXXX_5G
Open a web browser on the computer and configure the router according to the following main clues.
Type in admin for both the user name and password
and click Login.
Enter http://tplinkwifi.net in the address bar.
Alternatively, enter http://192.168.0.1 or
http://192.168.1.1.
b
Note: If the login window does not appear, please refer to FAQ->Q1.
Select your WAN Connection Type, or click Auto-Detect if you
are unsure what your connection type is. Click Next and follow
the instructions to continue.
Note: If an Internet connection is already established, the Quick Setup
wizard will bypass Step b and go to Step c .
Quick Setup-WAN Connection Type
admin
Auto-Detect
admin
Static IP
Dynamic IP (Most Common Cases)
PPPoE/Russian PPPoE
http://tplinkwifi.net
Login
L2TP/Russian L2TP
PPTP/Russian PPTP
Copyright © 2014 TP-LINK Technologies Co., Ltd. All rights reserved.
c
Choose the frequency you prefer and then click Next.
Quick Setup-Wireless Dual Band Selection
d
Verify or change the wireless network settings, and click Next.
e
2.4GHz & 5GHz Wireless Network Name and Password
Click Finish to complete the setup.
Quick Setup-Finish
Enjoy!
TP-LINK_XXXX / TP-LINK_XXXX_5G
Region:
Congratulations!
Security:
Password:
Back
Next
Next
Note: You may customize your 2.4GHz/5GHz wireless network name
and password. Once done, the wireless connection will disconnect
automatically, and you must then use the new wireless network
name/password to regain access to the Internet.
Wireless Network Name:
2.4GHz
5GHz
Back
Back
Now your wired and
wireless devices can
connect to the Internet !
XXXXXXXX
Next
Back
Finish
Method 2 Via CD Setup Wizard
Note: If you are using a computer that cannot run the mini CD, please refer to Method 1 for configuration.
1
2
Insert the TP-LINK Resource CD
into the CD-ROM drive.
Select Archer C20 and then click
Easy Setup Assistant.
3
Note: If the main page does not display on your
computer, browse the files on the CD and double
click Autorun.exe.
Choose your language, click NEXT
and the Easy Setup Assistant will
guide you through the setup process.
4
Click FINISH to complete the
setup.
Welcome
Install Router
Archer C20
Easy Setup Assistant
Install Router
Choose your language:
User Guide
Configure Router
English
Application Guide
Confirm Settings
USB Printer Setup
Browse CD
Congratulations!
Configure Router
Welcome
FINISH
Enjoy!
NEXT
EXIT
Confirm Settings
Now your wired and wireless devices can
connect to the Internet !
EXIT
Tether App
TP-LINK's Tether App lets you manage the router on smart devices. You can:
View the information about wireless clients.
Then, how to start?
1 Scan the QR code and download the TP-LINK Tether App from App
Store or Google Play.
Parent-control your kid’s access to the Internet.
Block or Unblock wireless access to the Internet via the router.
2
Ensure your smart device is wirelessly connected to the router.
Configure some basic settings for the router.
3
Launch the Tether App, and enjoy the easy management of the router.
USB Features
The USB port can be used for media sharing, storage
sharing and print sharing across your local network.
You can also set up an FTP server to access your
files remotely through the Internet.
USB sharing port
Note: To learn more about the USB features, please visit
http://tp-link.com/app/usb, retrieve the Resource CD attached in the
package, or simply scan the QR code with your smart devices.
Remote
Access via
FTP Server
Media
Sharing
Local
Storage
Sharing
Printer
Sharing
Frequently Asked Questions (FAQ)
Q1. What can I do if the login window does not appear?
Q3. How do I restore the router to its factory default settings?
A1. If the computer is set to a static or fixed IP address, change it to obtain an IP address automatically.
A2. Verify that http://tplinkwifi.net is correctly entered in the web browser. Alternatively, enter
http://192.168.0.1 or http://192.168.1.1 in the web browser and press Enter.
A3. Use another web browser and try again.
A4. Reboot your router and try again.
A5. Disable the network adapter used currently and then enable it again.
A1. While the Archer C20 is powered on, press
and hold the WPS/Reset button on the rear
panel of the router until all LEDs turn on
momently.
A2. Log in to the Web Management page of the
router, and go to System tools->Factory
Defaults, click Restore, then wait until the
progress bar loading finishes.
Q2. What can I do if I cannot access the Internet?
A1. Check if the Internet is working properly by connecting a computer directly to the modem via Ethernet
cable. If not, contact your Internet Service Provider.
A2. Open a web browser, enter http://tplinkwifi.net and try to set up again.
A3. Reboot your router and try again.
Q4. What can I do if I forget my password?
Note: For cable modem users, reboot the modem first. If the problem still exists, go to Network>MAC
Clone, then click Clone MAC Address and Save.
MAC Clone
WAN MAC Address:
Your PC’s MAC Address:
XX-XX-XX-XX-XX-XX
Restore Factory MAC
XX-XX-XX-XX-XX-XX
Clone MAC Address
WPS/Reset Button
Press & Hold 8 seconds
Web Management page password:
A. Restore the router to its factory default settings and then use the default User Name ‘admin’ and
Password ‘admin’ to log in.
Wireless Network password:
A1. The factory default password can be found on the product label printed on the bottom of the router.
A2. If you have changed your password, log in to the router’s Web Management page, go to
Wireless>Wireless Security to obtain or reset your password.
Note: If your questions are not answered here, please refer to http://www.tp-link.com/en/support/faq
and click Contact Technical Support for further assistance.
Save
LED Indicators
Name
Status
Indication
(Power)
Off
Flashing
On
Power is off.
The router is starting or upgrading firmware.
Power is on.
(Wireless 2.4G)
Off
On
The wireless function is disabled.
The wireless function is enabled.The router is working on 2.4GHz radio band.
(Wireless 5G)
Off
On
The wireless function is disabled.
The wireless function is enabled.The router is working on 5GHz radio band.
(Ethernet)
Off
On
No device is connected to the Ethernet ports.
At least one device has connected to the Ethernet ports.
(Internet)
Blue
Orange
Off
The Internet port is connected, and the Internet is accessible.
The Internet port is connected, but the Internet is inaccessible.
The Internet port is not connected, and the Internet is inaccessible.
(USB)
Off
Flashing
On
No USB device is plugged into the USB port.
A plugged-in USB device is being recognized.
The USB device has been successfully recognized.
(WPS)
Slow Flash
On
Quick Flash
A wireless device is connecting to the network by WPS function. This process will last in the first 2 minutes.
A wireless device has been successfully added to the network by WPS function.
A wireless device failed to be added to the network by WPS function.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement