Instructions / Assembly

Instructions / Assembly
Single Pole (One location) or 3-Way (Multi-location)
Scene Capable Incandescent/Magnetic Low Voltage or Fluorescent Dimmer
Cat. No. DZMX1, 1000VA, 1000W, 450W LED/CFL (Lighted)
120VAC, 60Hz
INSTALLATION INSTRUCTIONS
WARNINGS AND CAUTIONS:
• TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER at circuit breaker or fuse and test that power is off before wiring!
• TO AVOID FIRE, SHOCK, OR DEATH; DO NOT install to control a receptacle, a motor or a transfer operated appliance.
• To be installed and/or used in accordance with electrical codes and regulations.
• If you are unsure about any part of these instructions, consult an electrician.
• Use ONLY with the appropriate Advance Transformer 120V Mark 10™ Powerline or Lutron Tu-Wire® electronic ballasts for controlling the specific fluorescent lamps in Fluorescent Mode.
• Use with LED, CFL, incandescent, magnetic low voltage, fluorescent, or 120V halogen fixtures only. Use a Leviton electronic low voltage dimmer to control electronic (solid state) low voltage transformers.
• When retrofitting Mark 10™ Powerline dimming ballasts into fixtures that originally had Instant Start ballasts, the sockets MUST be replaced with Rapid Start sockets to allow proper dimmer operation
and prevent damage to the dimmer ballast. Refer to the instructions provided with the ballast.
• Decora® Z-Wave® control dimmers are not compatible with standard 3-way or 4-way switches. They must be used with compatible Vizia +® matching or coordinating remotes for multi-location dimming.
• Maximum wire length from dimmer to all installed remotes cannot exceed 300 ft.
• Dimmer may feel warm to the touch during normal operation.
Leviton’s Decora® Z-Wave® control components are designed to
communicate with each other via Radio Frequency (RF) to provide
remote control of your lighting. In a Z-Wave® network, each device
is designed to act as a router. These routers will re-transmit the RF
signal from one device to another until the intended device is reached.
This ensures that the signal is received by its intended device by
routing the signal around obstacles and radio dead spots. This dimmer
is compatible with any Z-Wave® enabled network, regardless of the
manufacturer and can also be used with other devices displaying the
Z-Wave® logo.
WARNING: TO AVOID FIRE, PERSONAL INJURY OR DEATH DO
NOT USE the remote for the control of high power heating appliances
such as portable heaters. Remember to exercise good common
sense when using the Timer features of your remote, especially when
scheduling unattended devices. There can be some unexpected
consequences if not used with care. For example, an empty coffee
pot can be remotely turned on. If that should happen, your coffee pot
could be damaged from overheating. If an electric heater is turned on
by remote control while clothing is draped over it, a fire could result. DO
NOT USE the remote for the control of high power heating appliances
such as portable heaters. This device will not control lighting that is
used with electronic low-voltage and high frequency power supply
transformers, nor high pressure discharge lamps (HID lighting). This
includes mercury-vapor, sodium vapor and metal halide lamps.
MULTI-DEVICE APPLICATION
Lutron Tu-Wire®:
In multi-dimmer installations, the reduction of the dimmer’s capacity is
required. Refer to the chart for maximum load per dimmer.
To determine total ballast load, add the line current found on the ballast label
for all ballasts in the circuit. This will indicate the total load for the control.
Remove all
inner side
sections
NOTE: Use check boxes
•
•
•
•
•
•
•
Soft fade ON/OFF
Scene capable
ON/OFF LED and Brightness level LED
Two way communication
RF reliability
Ease of installation – No new wiring
Compatible with other Z-Wave® enabled devices
MAXIMUM LOAD PER DIMMER FOR MULTI-DEVICE
Load
Single
Two Devices
More than 2 Devices
Incand
1000W
800W
650W
Mag LV
1000VA
800VA
/&&
/.
/&&
/.
/&&
/.
/&&
/.
/&&
/.
/&&
/.
/&&
/.
/&&
/.
/&&
/.
/&&
/.
/&&
/.
Pliers
Ruler
Your device may include color options. To change color of the face
proceed as follows:
Line up tabs
and press in sides
one at a time to attach
INSTALLING DIMMER BY ITSELF
OR WITH OTHER DEVICES
If installing Dimmer in a single device application, proceed with the
INSTALLING YOUR DIMMER section. If installing Dimmer in a
multi-device application, proceed as follows:
Black
White
2
Rating
Single
Two Gang
More than 2 Gang
1000VA
800W
640W
520W
Advance
Mark 10TM
Powerline
Part No.
Lamp
White
REZ-2Q18-M2-LD
REZ-1T32
REZ-2Q26
REZ-1T32
REZ-1T42
REZ-1Q18-M2-BS
REZ-1Q18-M2-LD
REZ-2Q18-M2-BS
REZ-1T32
REZ-1T42-M2-BS
REZ-1T42-M2-LD
REZ-2Q26
REZ-2Q26-M2-BS
REZ-2Q26-M2-LD
REZ-1Q18-M2-BS
REZ-1Q18-M2-LD
REZ-2Q18-M2-BS
REZ-2Q18-M2-LD
REZ-1T42-M2-BS
REZ-1T42-M2-LD
REZ-2Q26-M2-BS
REZ-2Q26-M2-LD
REZ-1T42-M2-BS
REZ-1T42-M2-LD
REZ-2T42-M3-BS
CFM18W/GX24Q
CFM26W/GX24Q
CFM26W/GX24Q
CFM32W/GX24Q
CFM42W/GX24Q
CFQ18W/G24Q
CFQ18W/G24Q
CFQ18W/G24Q
CFQ26W/G24Q
CFQ26W/G24Q
CFQ26W/G24Q
CFQ26W/G24Q
CFQ26W/G24Q
CFQ26W/G24Q
CFTR18W/GX24Q
CFTR18W/GX24Q
CFTR18W/GX24Q
CFTR18W/GX24Q
CFTR26W/GX24Q
CFTR26W/GX24Q
CFTR26W/GX24Q
CFTR26W/GX24Q
CFTR32W/GX24Q
CFTR32W/GX24Q
CFTR32W/GX24Q
Single
Gang
Two
Ganged
More than
2 Gang
23
32
17
26
20
46
46
23
32
32
32
17
17
17
46
46
23
23
32
32
17
17
26
26
13
18
25
13
20
16
37
37
18
25
25
25
13
13
13
37
37
18
18
25
25
13
13
20
20
10
15
20
11
16
13
30
30
15
20
20
20
11
11
11
30
30
15
15
20
20
11
11
16
16
8
1
Coordinating Remote (no LEDs)
Black
(PRIMARY SIDE
OF MAGNETIC
LOW-VOLTAGE
TRANSFORMER)
3
Yellow/Red
Red
Black
Black
White
3-Way
1. Line or Load
(see important
instruction)
2. Neutral
3. Ground
4. First Traveler – note color
5. Second Traveler – note color
IMPORTANT: For 3-Way applications, note that one of the screw terminals
from the old switch being removed will usually be a different color (Black)
or labeled Common. Tag that wire with electrical tape and identify as the
common (Line or Load) in both the dimmer wall box and remote wall box.
Step 3 Preparing and connecting wires:
Pull off pre-cut insulation from dimmer leads. Make sure that
the ends of the wires from the wall box are straight (cut if
necessary). Remove insulation from each wire in the wall box
as shown:
5/8"
(1.6 cm)
Strip Gage
(measure bare
wire here)
• Pull off pre-cut insulation from dimmer leads.
• Make sure that the ends of the wires from the wall box are straight
(cut if necessary).
• Remove insulation from each wire in the wall box as shown.
• For Single-Pole Application, go to Step 4a.
• For 3-Way Coordinating Remote (no LEDs) Application, go to
Step 4b.
Insulating
Label
Green
Ground
BK
(unused)
Red
Dimmer
RD
YL/RD
Black
Hot (Black)
White
Green
Ground
(unused)
Yellow/
Red
Line
120VAC, 60Hz
Green
Ground
Neutral (White)
Hot (Black)
White
Yellow/Red
Single Pole
1. Line (Hot)
2. Neutral
3. Ground
4. Load
WH
Green
2
3
4
5
Cut
(if necessary)
5
2
(PRIMARY SIDE
OF BALLAST)
Max. # Ballasts/Dimmer for
Multi-gang
3
Yellow/
Red
1
Dimmer
3
4
4
Green
5
Terminal
Screw marked
Yellow/Red
(YL/RD)
Insulating label:
This wire is used in 3-way installations only.
For single pole installations, do not remove this insulating label.
2
RD
YL/RD
Black
NOTE: If the wiring in your wall box does not resemble any
of these configurations, consult an electrician.
1
Red
4
Step 4a Single Pole Wiring Application:
Step 2 Identifying your wiring application (most common):
Low-voltage dimmers are rated in Volt-Amps (VA). The maximum bulb wattage
is determined by the efficiency of the transformer in the low-voltage lighting
system. Transformer efficiencies will vary from different manufacturers;
consider 80% efficient as average. Use the chart to determine maximum bulb
wattage for typical transformer efficiency ratings.
2
1
4
MAXIMUM BULB WATTAGE
1
BK
3
650VA
Mark 10™ Powerline dimmers are rated in Volt-Amps (VA). The maximum
bulb wattage is determined by the efficiency of the Mark 10™ Powerline
ballast. The following table shows the maximum number of ballasts that can
be connected to a single dimmer for different Mark 10™ Powerline ballasts.
Also note that the table shows maximum ballasts for multi-gang installations.
Changing the color of your Dimmer:
Push in side at
tab to release
/.
MAXIMUM BULB WATTAGE
TOOLS NEEDED TO INSTALL YOUR DIMMER
Electrical Tape
Cutters
/&&
Terminal Screw
marked White (WH)
Red
Cat. No. DZMX1, 120V, For use with Advance Transformer
120V Mark 10TM Powerline Electronic Ballasts
Slotted/Phillips Screwdriver
Pencil
OFF POWER at circuit breaker or fuse and test that power
is off before wiring!
Dimmer
Coordinating Remote
1 - #12 w/ 1 to 3 #14, #16 or #18
2 - #12 w/ 1 or 2 #16 or #18
1 - #14 w/ 1 to 4 #16 or #18
2 - #14 w/ 1 to 3 #16 or #18
when Steps are completed.
3-Way Wiring with VP00R-10Z Coordinating
Remote (no LEDs) Application:
Step 4b
WIRE CONNECTOR / # OF COND.
COMBINATION CHART
WARNING: TO AVOID FIRE SHOCK OR DEATH; TURN
Step 1
Do not
remove
outer side
sections
Bend back and
forth to remove
side section
For non-standard wiring applications, refer
to Wire Nut and Connector Size Chart
INSTALLING YOUR DIMMER
MAXIMUM BULB WATTAGE AT 75% EFFICIENCY
FEATURES
DI-000-DZMX1-02A
Line
120 VAC,
60Hz
White
Neutral (White)
WIRING DIMMER:
Connect wires per WIRING DIAGRAM as follows:
WARNING: CONNECT A MAGNETIC LOW-VOLTAGE DIMMER ONLY
TO THE PRIMARY (HIGH-VOLTAGE) SIDE OF A MAGNETIC
LOW-VOLTAGE TRANSFORMER.
• Green or bare copper wire in wall box to Green dimmer lead.
• Line Hot wall box wire to Black dimmer lead.
• Load wall box wire to Red dimmer lead.
• Line Neutral wall box wire to White dimmer lead.
• Yellow/Red dimmer lead should have Red insulation label affixed.
NOTE: If insulating label is not affixed to Yellow/Red dimmer lead,
use electrical tape to cover.
• Proceed to Step 5.
WIRING DIMMER:
Connect wires per WIRING DIAGRAM as follows:
WARNING: FOR MAGNETIC LOW-VOLTAGE APPLICATIONS,
CONNECT DIMMER ONLY TO THE PRIMARY (HIGH-VOLTAGE)
SIDE OF A MAGNETIC LOW-VOLTAGE TRANSFORMER.
NOTE: When using the coordinating remote without LEDs, the dimmer
can be installed on either the Line or Load side of the 3-way circuit.
NOTE: Maximum wire length from dimmer to all installed remotes cannot
exceed 300 ft (90 m).
• Green or bare copper wire in wall box to Green dimmer lead.
• Line Hot (common) wall box wire identified (tagged) when removing
old switch to Black dimmer lead.
• First Traveler wall box wire to Red dimmer lead (note wire color).
• Remove Red insulating label from Yellow/Red dimmer lead.
• Second Traveler wall box wire to Yellow/Red dimmer lead
(note wire color). This traveler from the dimmer must go to the
terminal screw on the remote marked "YL/RD".
• Line Neutral wall box wire to White dimmer lead.
WIRING COORDINATING REMOTE:
Connect wires per WIRING DIAGRAM as follows:
WEB VERSION
INTRODUCTION
WARNINGS AND CAUTIONS:
• When magnetic low voltage circuits are operated at a dim level, with all lamps inoperative, excess current may flow through the transformer. To avoid possible transformer
failure due to overcurrent, use a transformer that incorporates thermal protection or a fuse at the primary windings.
• Recommended minimum wall box depth is 2-1/2".
• Use this device WITH COPPER OR COPPER CLAD WIRE ONLY.
• Use with compatible dimmable LED, CFL bulbs, incandescent or 120V halogen fixtures only. For a list of compatible LED and CFL bulbs refer to www.leviton.com.
• When multiple bulbs are used with one dimmer DO NOT mix bulb types. All bulbs shall be either LED; CFL or incandescent. Using the same make/model of each bulb will
enhance dimmer performance.
• Not for use with Vizia RF® lighting systems.
NOTE: "BK" and "RD" terminals on coordinating remote are unused.
Tighten both screws.
NOTE: Maximum wire length from dimmer to last remote is 300 ft (90 m).
• Green or bare copper wire in wall box to Green terminal screw.
• Load wall box wire identified (tagged) when removing old switch to First
Traveler (note color as above).
• Second Traveler wall box wire (note color as above) to terminal screw
marked "YL/RD". This traveler from the remote must go to the
Yellow/Red dimmer lead.
• Remove White insulating label from terminal screw marked "WH".
• Line Neutral wall box wire to terminal screw marked "WH".
• Proceed to Step 5.
Dimmer
Matching Remote
Additional
Neutral Wire
Black
2
4
Red
3
RD
1
Green
5
Yellow/
Red
Matching Remote (with LEDs)
Hot (Black)
Installation may now be completed by tightening
mounting screws into wall box. Attach wallplate.
White
1
YL/RD
4
2
BK
WH
3
Step 7 Restore Power:
5
Restore power at circuit breaker or fuse.
Installation is complete.
Dimmer
NOTE: To include your dimmer into a network, contact
Leviton’s Techline at 1-800-824-3005 or visit Leviton’s
website at www.leviton.com.
Black
BK
Green
Ground
Line
120VAC, 60Hz
YL/RD
Green
Ground
Yellow/
Red
Red
Ballast
Black
Primary
Side
White
White
Neutral (White)
NOTE: The dimmer must be installed in a wall box that has a Load
connection. The matching remote must be installed in a wall box with
a Line Hot connection and a Neutral connection. A Neutral wire to the
matching remote needs to be added as shown.
If you are unsure about any part of these instructions, consult an
electrician.
NOTE: Maximum wire length from dimmer to all installed remotes
cannot exceed 300 ft (90 m).
WIRING MATCHING REMOTE (wall box with line hot
connection):
Connect wires per WIRING DIAGRAM as follows:
• Green or bare copper wire in wall box to Green terminal screw.
• Line Hot (common) wall box wire identified (tagged) when removing
old switch and First Traveler to Remote terminal marked BK.
• Second Traveler wall box wire from dimmer to remote terminal screw
marked "YL/RD" (note wire color). This traveler from the remote
must go to Yellow/Red dimmer lead.
• Line Neutral wall box to remote terminal screw marked "WH".
WIRING DIMMER (wall box with load connection):
Connect wires per WIRING DIAGRAM as follows:
• Green or bare copper wire in wall box to Green dimmer lead.
• Load wall box wire identified (tagged) when removing old switch to
Red dimmer lead.
• First Traveler Line Hot to Black dimmer lead.
• Remove Red insulating label from Yellow/Red dimmer lead.
• Second Traveler wall box wire (note color as above) to
Yellow/Red dimmer lead. This traveler from the dimmer must go to
the terminal screw on the remote marked "YL/RD".
• Line neutral wall box wire to White dimmer lead.
• Proceed to Step 5.
Step 5 Testing your Dimmer prior to mounting in
wall box:
NOTE: If using in a dimmable fluorescent application see
Advanced Programming Feature B-4 prior to testing the device.
• Position all wires to provide room in outlet wall
box for device.
• Ensure that the word “TOP” is facing up on
device strap.
• Partially screw in mounting screws in wall box
mounting holes.
NOTE: Dress wires with a bend as shown in
diagram in order to relieve stress when mounting
device.
• Restore power at circuit breaker or fuse.
• Press pad until locator light is OFF. Lights
should turn ON. If lights do not turn ON, press
the right half of the DIM/BRIGHT Bar until the
lights brighten.
If lights still do not turn ON, refer to
the TROUBLESHOOTING section.
Chart B
ADVANCED PROGRAMMING FEATURES
TURN OFF POWER AT CIRCUIT
BREAKER OR FUSE.
FACTORY DEFAULT
If your dimmer is not responding, or you are unable to control it after
you have tried to Include/Exclude it multiple times, it may be necessary
to reset the dimmer to its original factory settings. To accomplish this,
proceed as follows:
• On the dimmer, engage the air-gap switch (refer to Operation
section) and wait 5 seconds. Press the push pad back into the frame
and hold push pad until the locator LED turns Amber and then turns
Red. The dimmer is now reset. Once the dimmer is reset, it will be
necessary to Re-Include it to a network before it can be used.
CAUTION: SETTING A DEVICE TO A FACTORY DEFAULT DOES
NOT EXCLUDE THAT DEVICE FROM A NETWORK. THE EXCLUSION
PROCEDURE MUST STILL BE FOLLOWED TO REMOVE THE DEVICE
FROM THE PRIMARY CONTROLLER’S INFORMATION TABLE.
FAILURE TO DO SO MAY RESULT IN SYSTEM THAT IS SLOW TO
RESPOND, OR MAY FAIL TO RESPOND TO SOME DEVICES.
Definition of A Modes
A-1) Energy Save: Sets the maximum brightness level for energy savings.
A-2) Minimum Brightness Level: Sets the minimum dimming level.
A-3) Preset ON Level: Sets the turn on brightness level regardless of the
previous set light level (formerly Dim Lock).
Definition of B Modes
B-1) ON Fade Rate: Sets the amount of time in seconds it takes the
lights to turn ON to maximum brightness.
B-2) OFF Fade Rate: Sets the amount of time in seconds it takes the
lights to turn OFF from maximum brightness.
B-3) LED Options: Sets the time period in seconds the Locator LED and
Brightness display will stay on before extinguishing.
B-4) Fluorescent Mode: Allows dimmer to control Mark 10 Powerline
dimming ballasts.
Definition of LEDs
Leftmost LED = LED 1
Rightmost LED = LED 7
NOTES:
• The device will exit programming mode
after 3 minutes of inactivity.
• Pressing the push pad at any time
during programming will advance the
device to the next programming mode.
push pad
Air-Gap Switch: On the dimmer only, engage the
air-gap switch by gently pressing the top of the push
pad until the bottom lifts completely out of the frame
and a click is heard (refer to Figure). LED's will turn
OFF. This will stop power to the fixture to replace the
bulb. After servicing is complete, press the push pad
back into place for normal operation.
Cleaning: Clean with a damp cloth. DO NOT use chemical cleaners.
FADE ON
TROUBLESHOOTING
FADE OFF
LED 1
0 seconds (instant)
0 seconds (instant)
LED 2 (Default)
0.5 seconds
0.5 seconds
LED 3
1.5 seconds
1.5 seconds
LED 4
3.0 seconds
3.0 seconds
LED 5
6.0 seconds
6.0 seconds
LED 6
10 seconds
10 seconds
LED 7
25 seconds
25 seconds
B-3) The Locator LED will blink 3 times per second to indicate Program
Mode B-3, LED Options. To change the LED Options settings, use
the DIM/BRIGHT Bar to move the LED to the desired preset setting
according to the Chart B-3. By tapping the Push Pad this setting
will automatically be saved and the device will advance to the next
Programming Mode B-4.
Chart B-3
1 2 3 4 5 6 7
LED Brightness
Display
Program Mode A
To enter Program Mode A:
Press and hold the Push Pad and then the right half of the
DIM/BRIGHT Bar (^) for 5 seconds until the Locator LED and leftmost
LED (LED 1) begin to blink.
A-1) Upon releasing the Push Pad and the right half of the DIM/BRIGHT
Bar (^), the Locator LED will continue to blink once per second and
the rightmost LED will illuminate to display the device is in Program
Mode A-1, Energy Save. The default energy save mode is 100% i.e.
full bright. To change the Energy Save level, use the
LED Brightness
DIM/BRIGHT Bar to move the corresponding LED to the desired
OPERATION
Display
discrete preset level according to Chart A. By tapping the Push Pad
NOTE: The locator light will illuminate when the load
this setting will automatically be saved and the device will advance
DIM/BRIGHT
is in the OFF position to facilitate access in the dark.
to the next programming mode, A-2.
Bar
NOTE: If using the dimmer in a 3-wayapplication, the
Chart A
lights will turn ON at brightness set on dimmer’s
Energy consumption
When indicator
DIM/BRIGHT bar. The lighting can be controlled
Light output is at
savings amounts to
light is at LED #
from either the dimmer or the remote location.
Push Pad (Default settings)
0%
7
100%
5%
6
97%
Turn ON from OFF position:
8%
5
95%
Tap – Lights turn ON to preset level.
Press and Hold – Lights turn ON to full bright.
4
90%
16%
3
85%
24%
Turn OFF from ON position:
2
80%
Tap – Lights turn OFF.
29%
75%
1
34%
DIM/BRIGHT Bar
Push
Locator
BRIGHTEN:
Pad
Light
Press the right half of the DIM/BRIGHT Bar – Lights
brighten to desired level.
DIM:
Press the left half of the DIM/BRIGHT Bar – Lights dim to desired level.
If you continue to hold, the lights will DIM to
minimum level and then turn OFF.
NOTE: When lights are OFF you can change the light level that the
lights will turn ON to using the DIM/BRIGHT Bar.
If there is a power outage, when the power is restored, the lights will
return to the last setting
Gently press top of
before the power interruption.
LED
LED
LOCATOR LED TIMEOUT LED BRIGHTNESS DISPLAY OPTIONS
LED 1 Active
Active
LED 2 Active
Turns off 5 sec. after use
• Lights Flickering
- Lamp has a bad connection.
- Wires not secured firmly with wire connectors of dimmer or
terminal screws of remote.
- If using in a dimmable fluorescent application see Advanced
Programming Feature B-4.
• Light does not turn ON and Locator LED does not turn ON
- Circuit breaker or fuse has tripped.
- Lamp is burned out.
- Neutral not wired to Dimmer (White wire).
- Confirm that the device is being supplied from a 120V, 60 Hz AC
source ONLY.
- Confirm that unit is programmed properly. Repeat "TO INSTALL"
section to verify that it has been included in the Z-Wave® network.
• Intermittent dimmer operation
- Confirm that the Load being controlled does not exceed the
1000VA dimmer limit.
• Remote does not operate lights
- Ensure that total wire length does not exceed 300 ft.
- Ensure wiring is correct.
• LED bulb is illuminated even when off
- Replace the bulb with a different brand or a higher wattage rating.
LED 3 Turns off 5 sec. after use Active
LED 4 Turns off 5 sec. after use Turns off 5 sec. after use
LED 5 Active
LED Bar active
LED 6 Active
LED Bar turns off 5 sec. after use
For additional information, contact Leviton’s Techline at
1-800-824-3005 or visit Leviton’s
website at www.leviton.com
LED 7 Turns off 5 sec. after use LED Bar turns off 5 sec. after use
B-4) The Locator LED will blink 4 times per second to indicate Program
Mode B-4, Fluorescent Mode. Default operation mode is
incandescent/magnetic low voltage mode. To change from normal
to fluorescent mode, use the DIM/BRIGHT Bar. Press and hold
the right half of the DIM/BRIGHT Bar (^) until LED is lit (default
setting is LED OFF). By tapping the Push Pad this setting will
automatically be saved and device will exit Programming Mode B.
A-2) The Locator LED will blink 2 times per second to indicate the device
is in Program Mode A-2, Minimum Brightness Level. The default
Minimum Brightness Level is LED 1. To change the Minimum
Brightness Level from 1-50%, use the DIM/BRIGHT Bar. The light
output will reflect the minimum brightness level selected. By tapping
the Push Pad this setting will automatically be saved and the device
will advance to the next programming mode, A-3.
A-3) The Locator LED will blink 3 times per second to indicate Program
Mode A-3, Preset ON Level. To change the current Preset ON Level
from 1-100%, use the DIM/BRIGHT Bar. If this feature is not desired,
press and hold the left half of the DIM/BRIGHT Bar (v) until no
LED is lit (default setting). By tapping the Push Pad this setting will
automatically be saved and the device will exit Programming Mode A.
Program Mode B
To enter Program Mode B:
Press and hold the Push Pad and then the left half of the DIM/BRIGHT Bar
(v) for 5 seconds until the Locator LED and rightmost LED (LED 7) begin
to blink.
B-1) Upon releasing the Push Pad and the left half of the DIM/BRIGHT
Bar (v), the Locator LED will continue to blink once per second
indicating the dimmer is in Program Mode B-1, ON Fade Rate. To
change the ON Fade Rate, use the DIM/BRIGHT Bar to move the
LED to the desired preset level according to Chart B. By tapping the
Push Pad this setting will automatically be saved and the device will
advance to the next programming mode, B-2.
B-2) The Locator LED will blink 2 times per second to indicate Program
Mode B-2, OFF Fade Rate. To change the OFF Fade Rate, use
the DIM/BRIGHT Bar to move the LED to the desired preset level
according to Chart B. By tapping the Push Pad this setting will
automatically be saved and the device will advance to the next
programming mode, B-3.
Covered by U.S. Pat. Nos.: 7,756,556; 7,985,937; 8,003,904;
D609,650 and corresponding foreign equivalents.
Licensed under U.S. Pat. Nos. 5,905,442, and 5,982,103
FCC COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation of the device.
This equipment has been tested and found to comply with the limits for a
Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment OFF
and ON, the user is encouraged to try to correct the interference by one or
more of the following measures:
•
Reorient or relocate the receiving Antenna.
•
Increase the separation between the equipment and the receiver.
•
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
•
Consult the dealer or an experienced radio/tv technician for help.
FCC CAUTION
Any changes or modifications not expressly approved by Leviton
Manufacturing Co., Inc., could void the user's authority to operate the
equipment.
Copyright and Trademark Information
This document and all its contents herein are subject to and protected by
international copyright and other intellectual property rights and are the
property of Leviton Manufacturing Co., Inc, its subsidiaries, affiliates and/or
licensors.
Use herein of third party trademarks, service marks, trade names, brand
names and/or product names are for informational purposes only, are/may
be the trademarks of their respective owners; such use is not meant to imply
affiliation, sponsorship, or endorsement.
No part of this document may be reproduced, transmitted or transcribed
without the express written permission of Leviton Manufacturing Co., Inc.
FOR CANADA ONLY
For warranty information and/or product returns, residents
of Canada should contact Leviton in writing at Leviton
Manufacturing of Canada Ltd to the attention of the Quality
Assurance Department, 165 Hymus Blvd, Pointe-Claire
(Quebec), Canada H9R 1E9 or by telephone at 1-800-405-5320.
Z-Wave is a registered trademark of Sigma Designs Inc. and/or its subsidiaries
© 2014 Leviton Mfg. Co., Inc.
LIMITED 5 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for five years from the purchase date. Leviton’s only obligation is
leviton.com or call 1-800-824-3005. This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused, opened, abused, or
accordance with any labels or instructions. There are no other or implied warranties of any kind, including merchantability and fitness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty,
Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this warranty obligation. The remedies provided herein are the
WEB VERSION
Step 6 Dimmer Mounting:
Step 4c 3-Way Wiring with VP00R-1LZ Matching
Remote (with LEDs) Application:
DI-000-DZMX1-02A
to correct such defects by repair or replacement, at its option. For details visit www.
altered in any manner, or is not used under normal operating conditions or not in
including merchantability and fitness for a particular purpose, is limited to five years.
exclusive remedies under this warranty, whether based on contract, tort or otherwise.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement