Headphone Divine Manual
HeadPhone Divine
Owners Manual
IMPORTANT SAFETY INSTRUCTIONS
1. Heed all warnings
2. Keep and follow all instructions.
3. The operating temperature range: from 0 degree Celsius to 45 degree
Celsius.
4. DO NOT use this apparatus near water
5. Clean only with dry cloth
6. DO NOT disassemble or replace the battery. If you suspect there is
something wrong with the battery, please carry the unit to the service
center for help.
7. CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN
INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE
INSTRUCTIONS
8. The battery should not be disposed together with other waste. The
battery has to be disposed at an authorized place for recycling of
electrical and electronic appliances. By collecting and recycling waste,
you help save natural resources, and make sure the product is disposed
in an environmentally friendly and healthy way.
9. Unplug this apparatus during lightning storms or when unused for
long periods of time
10.DO NOT install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat
11.Only use accessories specified by the manufacturer
12.Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as liquid has
been spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or
has been dropped.
13.If at any time in the future you should need to dispose of this product
please note that: Waste electrical products should not be disposed of
with household waste. Please recycle where facilities exist. Check with
your Local Authority or retailer for recycling advice. (Waste Electrical
and Electronic Equipment Directive)
2
CONTENTS
Introduction.........................................................4
About HeadPhone Divine.......................................4
About XTZ............................................................4
Technical presentation..........................................5
Controls and inputs...............................................5
Using HeadPhone Divine.......................................6
Technical specifications...................................... 11
Service & support................................................12
3
INTRODUCTION
The HeadPhone Divine offers great possibilities, so in order to utilize
your new headphones in the best way; you should carefully read
through this manual before using the headphone for the first time.
If you have no previous experience of this kind of headphone, or if you
have any questions, feel free to contact our free of charge support and
we will help you. (See further under the heading of Support on the last
page of this manual).
ABOUT HEADPHONE DIVINE
The HeadPhone Divine is a bluetooth headphone with a built in
microphone and player controls, as well as NFC for easier pairing and a
passive connection for traditional headphone use. Headphone Divine.
To improve the sound of the headphones we supply the XTZ Player app
which uses DSP technology from DIRAC.
ABOUT XTZ
PHILOSOPHY
XTZ GOALS
Our reference and starting point is to recreate a natural sound, but also
in respect to the fact that acoustics and sound always is a matter of
taste.
To provide the optimal relation between price, performance and
quality on the market.
Our concept:
- To produce the perfect compromise.
- Cost-effective manufacturing at a large scale.
- The quality of our products is more important than the marketing.
- Reduce the number of middlemen.
CONTACT US
Website: www.xtz.se
E-mail: [email protected]
4
TECHNICAL PRESENTATION
HEADPHONE DESIGN
This headphone is a supra-aural, or on-ear wireless headphone that is
made for portable use. The main parts are made in durable plastic, both
for its light weight and its acoustical properties. The hinges are made in
steel to increase durability, and soft and supple leatherette is used on
the cushions and headband for comfort and style.
DRIVER
HeadPhone Divine uses a 40 mm lightweight driver powered by a
neodymium magnet for the entire frequency spectrum.
BLUETOOTH 4.0
With the latest Bluetooth 4.0 and aptX technology transfer of high
definition audio over a distance of up to 10 m is made possible. This
technology is compatible with Windows devices, Apple OSX and iOS
devices, and with Android devices, provided that they support Bluetooth
4.0.
CONTROLS AND INPUTS
1. 2. [ + ] 3. [ - ]
4. [ » ]
5. [ » ]
Multifunctional button
Volume up button
Volume down button
Fast-Forward button
Fast-Backward button
6. [
7.
8.
9.
10.
5
] Play, Pause, Answer button
Indicator Light
NFC
Micro-USB Port
3.5 mm AUX port
USING HEADPHONE DIVINE
Before using the headset, you must fully charge the battery and connect
the headset to your respective Bluetooth device.
CHARGING THE BATTERY
The headset contains a battery capable of up to 14 hours of usage. To
charge the battery, the headset has to be connected with the included
USB cable. The cable has two different sized ends.
First, take the Micro-USB end and plug into the USB entry port in the
right side of the headset. The other end of the cable is fitted with a
standard USB plug. Plug the end in the USB port of the computer, wall
charger, or other compatible devices with an USB port.
The indication light is on the right side of the headset. When the battery
is charging, a constant green light will be on. Once the battery is fully
charged, the green indicating light will be turned off.
TURNING ON YOUR
HEADPHONE
To turn the headset on, locate the multifunctional button on the right
side of the headset. The button is located next to the Micro-USB port on
the headset. Press the button and hold for 3 seconds and the indicating
light will show a blue flash followed by two red flashes. The headset is
now turned on (but not yet paired).
PAIRING THE HEADPHONE
WITH YOUR DEVICE
To pair the headset with your music player, ensure that the respective
device is turned on and the Bluetooth function is active. When setting
the headset for pairing mode, make sure the headset is off, and then
press the multifunctional button and hold for 5 seconds. The indicating
light will show the below process.
1. First the light will show a blue flash once.
2. Then for a few seconds it will flash red.
3. After red it will blink blue flashes and the headset is now in pairing
mode.
On your respective device you should search for the signal and use the
device’s functions to connect. On the list of found devices you select
”HeadPhone Divine” to establish the connection.
Some devices require a passcode to connect with a newly established
Bluetooth apparatus. Enter passcode: 0000 if necessary.
When the connection is established, the headset’s light indicator will
flash a blue light two times every 5 second to verify the connection.
PAIRING WITH NFC
BLUETOOTH
The headset has the NFC (Near Field Communication) Bluetooth
technology incorporated and can be used if your respective music
device is compatible. To pair with NFC, please follow the steps:
1. Enable the NFC function on your music device.
2. Gently let the headset and your music device meet, by holding
them close together. The NFC is located on the center of the left
earcup.
3. Your music device should now recognize the signal from the
headset.
a. If the music device and the headset are pairing for the first time,
you will need to accept the pairing on the music device
4. When the signal has been accepted on your music device, the
headset will be paired and ready for use.
6
Your connection should now be established and the headset can be
used to listen to music, accept phone calls and much more.
LISTENING TO MUSIC
-VOLUME CONTROL
To adjust the volume of the headset use the volume button located on
the right earcup. The button has a plus [+] and minus [-] symbol. The [+]
volume button is related to the plus symbol and will turn up the volume
if pressed. The [-] volume button is related to the minus symbol and will
turn down the volume of the headset.
LISTENING TO MUSIC
-PLAY AND PAUSE MUSIC
When the headset is connected to your music player, you can easily and
quickly start listening to music by pushing the [
] play & phone
button one time, located on the right earcup.
When you want to resume the paused song, you push the [
] play
& phone button once again and the song will begin.
NEXT AND PREVIOUS
TRACK
The “»” and “«” key that is also located on the right earcup can also
easily be used to navigate between the various songs on your music
player.
• If you wish to skip to the next track, push the “»” key once.
• If you wish to go back to the previous song, push the “«” key two
times, press the “«” key once to go back to the beginning of the
current song.
RECEIVE CALLS
If the headset is connected to your mobile phone you can use it to
answer phone calls. You can use the [
] key to navigate your
incoming calls.
• Making a call - in order to make a call when your headset is
connected to your mobile phone, you will have to dial your mobile
phone in the normal way or by using voice dialing (if enabled by
your respective phone).
• Answering a call - to answer an incoming call press the [
] key
one time.
• To end a call - when finishing the call press the [
] key once
more.
• Rejecting a call - if you wish to reject an incoming call you have to
press the “ ” key and hold for 2 seconds.
DISCONNECT THE
HEADSET
If you wish to disconnect the established connection between the
headset and your respective device, simply enter the Bluetooth function
on your music player and shut down the connection or switch off the
headset.
SWITCH OFF THE
HEADSET
If you wish to turn off the headset, Press the multifunctional button and
hold for 3 seconds until the indicator will show a constant red light. Let
go of the button and the device is now turned off.
CLEAR SETTINGS OR
RESET THE HEADSET
To clear the pairing settings from the headset, you should firstly turn
off the headset. Then press and hold the multifunctional button
simultaneously with the [-] volume button. The two buttons has to be
pressed and hold for 8 seconds. The indicating light will switch between
a red and blue flash 3 times and the headset has now been clear the
pairing settings.
To hardware reset the headset, plug and unplug the 3.5 mm AUX cable.
LISTENING TO MUSIC USE OF AUX CABLE
The headset has an AUX entry build-in on the left side of the headset.
The headset does not need to be turned on for the AUX port to work.
Simply plug the cable in the headset and into your device.
Note: When the AUX cable is inserted, the Bluetooth function and the
build-in microphone will be disabled.
7
TECHNICAL SPECIFICATIONS
CONSTRUCTION TYPE
DIMENSIONS
WEIGHT
BLUETOOTH INTERFACES
OUTPUT LEVEL
FREQUENCY RESPONSE
DRIVERS
BATTERY LIFE
BLUETOOTH CONNECTION
RANGE
Battery powered Bluetooth headphone with built in microphone, NFC
pairing, play controls, USB charging and a 3.5 mm port for conventional
headphone use.
172 x 150 mm (W x H), Cup diameter 65 mm
170 g
HSP, HFP, A2DP, AVRCP
97 dB at 1 kHz, max 104 dB
15 - 32 000 Hz
40 mm broadband driver with Neodymium magnet
Up to 14 h of continuous play
Up to 10 m
8
(without cushions)
SERVICE & SUPPORT
”DO IT YOURSELF” - SERVICE We apply “do-it-yourself” service on all XTZ products. If you by yourself
are able to find out what part of the headphone is defective, you are
fully allowed to unmount that part and send it back to us for exchange.
IMPORTANT!
Always contact your dealer or us before taking the headphone apart. It
can also help you finding the fault.
You can of course always choose to return the whole headphone;
therefore you should save the original package.
IF SOMETHING IS BROKEN
WHERE TO SEND THE
PRODUCT FOR A WARRANTY
REPAIR
If you cause additional defects by yourself when unmount the defective
part, the warranty still applies if it is obvious that the part had a
manufacturing defect. In other cases however, the warranty does not
apply if you cause other defects on the headphone
For service we refer to your retailer.
For questions regarding service, contact us by email: [email protected]
Website: www.xtz.se
SUPPORT
To aid service, XTZ products
are constructed and produced using common technology, so that basically most
people are able to “unscrew”
the headphone using common tools..
Please contact our free of charge support if you need installation advice,
or if any problem occurs during the installation.
Contact us by e-mail [email protected] and include your phone number if
you wish verbal help, and we will call you back.
9
ALWAYS pack the product /
part very carefully. Unfortunately damages during transportation are very common.
If the package is weak, the
transporting company does
not compensate damages.
Always enclose a copy of the
receipt and a description of
the defect.
EMC/RF REQUIREMENTS
Europe—EU Declaration of Conformity:
The equipment complies according to the Radio Equipment and
Telecommunications Terminal Equipment Directive 1999/5/EC. This
equipment meets the following conformance standards:
• Safety : EN 60065:2002/A12:2011
• Health: EN 62479: 2010
• EMC : EN 301 489-1 V1.9.2
• EN 301 489-17 V2.2.1
• EN 55013: 2013
• EN 55020:2007/A11:2011
• Radio: EN 300 328 V1.8.1
FCC REQUIREMENTS
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: To comply with the limits of the Class B digital device,
pursuant to Part 15 of the FCC Rules, this device is comply with Class
B limits. All peripherals must be shielded and grounded. Operation
with non-certified peripherals or non-shielded cables may results in
interference to radio or reception.
MODIFICATION: Any changes or modifications not expressly approved
by the grantee of this device could void the user’s authority to operate
the device.
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
MANUFACTURER’S NAME AND ADDRESS
XTZ Sound in Balance AB
Gamla Nissastigen 19, 31441 Torup, Halland, Sweden
10
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement